MP-33 RRNMU/SG/02- Sagar-Furniture

Amount

Providing and Installation complete of Furniture including related allied works and maintenance of same in RRNMU Buildings

Providing And Placing of BED SIDE TABLE : Body and drawer panels of Bed side table are made of 18 mm thick Prelaminated Particle Board. All the exposed edges are edge banded with 0.8 mm thick PVC edge banding, Side panels are made of 18 mm thick Prelaminated Particle board with imported H.D.F. foil wrapped decorative trim FIxed on to it. The high quality hardware used like Roller slides, Hinges , minifix, dowels is of make Hettich or equipment . Finish 18 mm thick Prelaminated Particle Board is in Walnut shade. Knock Down construction. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of Mobile Pedestal : Under Main Table - Supplying free standing pedestal for office table with dimensions 390 (w) X 440 (d) X 646 (h).Free Standing Full Height Mobile Box Box File. Construction is of Welded Assembled 0.8 thk CRCA for Body Shell, Drawer Front & tray, Front Side Stiffener, Rear Side Stiffener. 1.2 thk CRCA Top Stiffener & Bottom stiffener. drawer fronts are Metal Front Straight Edge. All Drawers with Double extension precision ball slide 390 wide Pedestals File drawer suitable for storing Fullscape Ezee & Visa files in Depth wise manner. A4 files in width wise manner For Drawer pulling, side wise tapered recess provided in shell behind Drawer Fronts. Locking is of 10 lever Cam Lock & Central RH locking with actuator & lock channel mechanism for ‘BoxBoxFile’Pedestal. Top panel Metal Straight Edge Top. the castors are of Swiveling nonlockable Castors mounted below the body shell for Free Standing Full Height Mobile Pedestal. Fifth roller arrangement mounted below File drawer to avoid toppling of unit when file drawer is pulled out. Finish is of Epoxy Polyester Powder coated to the thickness of 50 microns (+/10). As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of DRESSING TABLE WITH STOOL : Dressing Table should be made of size - 450W x 440 D x 1710 H mm & Dressing Stool should be made of size - 335 W x 360 D x 450H mm. Panels of Dressing table & Stool should be made of 18 mm thick Prelaminated Particle Board .All the exposed edges are edge banded with 0.8 mm thick PVC edge banding. Side panels should be made of 18 mm thick Prelaminated Particle board with imported H.D.F. foil wrapped decorative trims to be fixed on to it. Mirror panel should made of 18 mm thick particle board with 4 mm thick mirror fixed on to it. Supporting pipe used for fixing the mirror frame is to be made of M.S. 25 mm square pipe of thickness 1.2 mm.Stool seat should be made of foam with fabric wrapped on to it. The high quality hardware shall be used like Roller slides, Hinges , minifix, dowels is of make Hettich or equipment. 18 mm thick Prelaminated Particle Board shall be in Walnut shade finish & knock down condition. Metal pipe should be powder coated in shade Metallic Silver Grey to thickness of 50 microns(+-10). As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of Single Bed : The Bed shall be of Size – 2060 L x 1131W x 945 H mm. Bed is constructed around metal frame Metal frame made of M.S. Channels in 1.0mm thickness. Horizontal plinths and bottom plinth are made of 25mm Thick Prelaminated Particle Board. Head Board is made of 18 mm thick Prelaminated Particle board with imported H.D.F. foil wrapped decorative trims fixed to it. Side tail board is made of 18 mm thick Prelaminated Particle Board with importred H.D.F. foil wrapped decorative trims fixed on to it. Mattress panels of bed are made of 18 mm thick Prelaminated Particle Board with all exposed edges banded with 0.8 mm Thick PVC edge banding. Construction – Knock Down. Finish 18 mm thick Prelaminated Particle Board is in Walnut shade. Metal frames are power coated in shade Mat Black to the thickness of 50 microns. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing DISPLAY RACK : The display rack should be knockdown in construction. Nylon rollers with ball bearing are to be provided for easy tray movement. The inclined retractable tray for display and horizontal metal shelf for storing should be provided. Widthwise stackability should be possible to create bank of racks. The shelf and the retractable tray should be made of 0.8 mm thick CRCA sheet. The sides Steel inserts should be provided in wooden panel for gripping of screws. Total five compartments should be provided. All the metal components should be epoxy powder coated to the thickness of 40-60 microns. Overall width 900 mm W x 1900 mm H x 400 mm D. As per drawing & specification and directed by Engineer-in-Charge. Make - Knoll/Godrej/ Haworth/ Steelcase/ Herman Millar//WiproMethodex/durian or Equivalent.

Providing And Placing EXECUTIVE BACK UNIT : The back unit of Size - 1800 x 500 x 750 mm. Top panel should be made up of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Slide door unit should be made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves.. Shutters shall be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Shutters should have a soft closing & anti slam mechanism. Handles are provided for ease of opening.Storage is provided with lock for security. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing EXECUTIVE BACK UNIT : The back unit of Size - 1650 x 500 x 1800 mm. Top panel should be made up of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Slide door unit should be made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves.. Shutters shall be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Shutters should have a soft closing & anti slam mechanism. Handles are provided for ease of opening.Storage is provided with lock for security. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of EXECUTIVE MAIN TABLE + SIDE TABLE WITH PEDESTAL : The Main Table should be of Size - 2350 x 1150 x 750 with ERU With Pedestal of Size - 1200 x 500 x 750. The primary work surface should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Softclosing access flap with in-build power box are provided on work surface for wire management Secondary work surface ( ERU ) of size - 1200 x 500 x 750 should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Modesty Panel should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening Pedestals are provided with lock for security .As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of CENTER TABLE for EXECUTIVE Rooms : The table should be of size 1000 W x 600 D x 428 H with Glass top of 08 mm thk tempered and Solid rubber wood legs and frame with MS sheet as bottom shelf. POWDER COATING COLOR & DFT IN MICRONS -40-80 Microns . As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of Executive High Back Chair : The High back chair should be made up of 1.2 ±O.1cm. thick hot-pressed plywood and upholstered with-fabric upholstery covers and moulded Polyurethane foam. The back is designed with contoured lumber support for extra comfort. The seat has extra thick foam on front edge to give confort to popliteal area. the high back size is 47 cm W x 69.5cm H and the seat size is 47 cm W x 48 cm D. The HR PU foam is moulded with density 45+-2 kg/m cube and hardness load 16 +- 2 kgf as per IS:7888 fof 25% compression. The one piece armrest are injection moulded from black Co Polymer PP. Centre tilt syncro mechanism has 360 degree revolving type, upright position locking, tilt tension adjustment, seat/back ratio of 1:3. The pneumetic height adjustment has an adjustment stroke of 12+- 0.3 cm. Telescopic bellow assy: it is 3 pc telescopic type and injection moulded in black PP. The pedestal is injection moulded in black 33% glass filled Nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal is 66.3 +- 0.5 cm. pitch dia (76.3 +- 1 cm with castors). The twin wheel castors are injection moulded in black nylon. As per drawing & specification and directed by Engineer-in-Charge. Make - Godrej/ Haworth/ Herman Millar//WiproMethodex/durian or Equivalent.

Providing And Placing of Mid back chairs : The chair having seat/back assembly made up of 1.2 ±O.1cm. thick hot-pressed plywood measured as per QA method and upholstered with-fabric upholstery covers and moulded Polyurethane foam. The back foam to be designed with contoured lumbar support for extra comfort. The seat should have extra thick foam on front edge to give comfort to popliteal area. Back Size should be 47.5 cm. (W) x 58.0 cm. (H) - SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D). The Chair should have HIGH RESILIENCE (HR) POLYURETHANE FOAM.moulded with density =45±2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression and ARMRESTS which are one-piece injection moulded from black Co. polymer Polypropylene. The chair should have CENTERTILT.SYNCHRO MECHANISM with the following features:• 3600 revolving type.• Upright-position locking • Tilt tension adjustment • Seat/back tilting ratio of 1:3. The Chair shall have PNEUMATIC HEIGHT ADJUSTMENT at stroke of 12.0 ±0.3cm. with TELESCOPIC BELLOW ASSEMBLY with 3 piece telescopic type and injection moulded in black Polypropylene.PEDESTAL ASSEMBLY with injection moulded in black 33% glass-filled.Nylon-66 and fitled with 5.nos. twin wheel castors. The pedestal shall be 66.3 ±O.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The twin wheel castors shall be injection moulded in Black Nylon. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of Visitor Chair Fixed : The chair having SEAT/BACK ASSEMBLY made up of 1.2 ±O.1cm. thick hot-pressed plywood and upholstered with-fabric upholstery covers and moulded Polyurethane foam. The back foam shall be designed with contoured lumbar support for extra comfort. The seat to be extra thick foam on front edge to give comfort to popliteal area. BACK SIZE shall be 47.5 cm. (W) x 58.0 cm. (H)and SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D) with HIGH RESILIENCE (HR) POLYURETHANE FOAM to be.moulded with density =45±2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The ARMRESTS :The one-piece armrests are injection moulded from black Co. polymer Polypropylene. The reading chairs shall have TUBULAR FRAME which is powder coated (OFT 40-60 microns) tubular frame is cantilever type & made of 02.54 ±0.03cm. x 0.2 ±0.016cm.thick. M.S. ER.W. Tube. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of Visitor Chair Fixed with Armrest : BACK SIZE - WIDTH (W) : 42.0 CM;DEPTH ; HEIGHT (H) : 26.5 CM . SEAT SIZE (W) : 42.0 CM X 42 CM (D).The HR polyurethane foam should moulded with density = 45+/-2 kg/m³ and hardness 16 ± 2 kgf as per IS:7888 for 25% compression.The understructure assembly should be cantilever type mainframe of 2.54+/-0.03cm x 0.2+/- 0.016cm thk M.S.E.R.W tube and black powder coated(DFT 40-60 microns). The armrest assembly should be made in twin tube form using 1.58 cm(5/8') x 0.16+/-0.0128 cm thick MSERW tube and black powder coated (DFT 40-60 microns). Chair Dimension shall be 54.0 CM.(W) x 59.5 CM.(D) x 82.5 CM. (H) . As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of EXECUTIVE BACK UNIT : The back unit of Size - 2350 x 500 x 750 mm. Top Panel should be Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Slid e door unit should be made up of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves. Shutters are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Shutters shall have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security. As per drawing & specification and directed by Engineer-in-Charge. Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of PREMIUM EXECUTIVE SUITE consist of MAIN TABLE + SIDE TABLE WITH PEDESTAL : The Main Table should be of Size - 2100 x 1050 x 750 with ERU with Pedestal of Size - 1200 x 500 x 750.The primary work space should be made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Secondary Work Unit should be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Softclosing access flap with in-build power box are provided on work surface for wire management modesty panel should be made of 25mm thick MDF one side laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Under structure should be made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated pedestal shall be Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestal is provided with lock for security. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of CPU TROLLEY WITH CASTORS : Metal Tray should be made of 1.0 mm thick MS CRCA Sheet and Side support is made Lockable/Non-lockable twin wheel castors are injection molded in Black of 0.8 mm thick MS CRCA Sheet . As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of Dining Table : 8 Seater Dining table with overall dimensions of 970mm W x 2100mm L x 750mmH. The Table shall have Glass top and wooden understurture having 12mm tempered Glass with decorative etching work. The Glass top shall be connected with tapered legs with UV disc. These tapered legs are connected with two rectangular metal (SS) bars which hold the lower wooden (MDF) shelf of white cedar colour suspended underneath for storage. The tapered legs provide a sense of lasting stability and draw attention because of the luminous PU finish and the smooth surface. This eight seater dining table shall be preferably in a dark chocolate finish wooden base with a beveled glass tabletop. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of Dining Chair :The dining chair should be dark chocolate finished upholstered dinning chair is to be simple yet contemporary for the modern dining room. The chair shall feature a green coloured chenille fabric seat supported by slightlybent back legs and straight front legs . The seat back features a cut out taporized shaped on a slightly curved back pannel. it should not only enhances the aesthetic of thechair but also has a functional aspect aas it helps in lifting or holding the chair Size – 560 x 460 x 905 x 470mm . Net Weight (Kg) 7.95 ( Appro.). As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of Table for Lab : The table should be of size width 1500mm X depth 750mm X height 728mm worksurface made of 18mm thk. Pre Laminated Particle Board (PLB) All work surface edges are duly sealed with 2mm thick PVC Edgebanding. Modesty panel made of 18mm thk. Pre Laminated Particle Board (PLB) All work surface edges are duly sealed with 2mm thick PVC Edgebanding. Rectangular frame of Fabricated component in 1.2mm thick CRCA (IS:513), Finish: Powder coat (Epoxy polyester). Legs made of Fabricated component in (Epoxy polyester) & other parts of 0.6mm thick CRCA (IS:513), Finish: PowderPowder coat (Epoxy polyester).Pedestal frame assembly made of 1.2mm thick CRCA (IS:513), Finish: Powder coat38mmx25mmx1.2mm thick MS ERW Tube (IS:7138), Finish: Powder Coated coat (Epoxy polyester) with 10 Lever Cam Lock & Injection Moulded Polypropylene Handle with Nylon6 & MS Bolt levellers. Wire carrier made of 0.7mm thick CRCA (IS:513), Finish: Powder coat (Epoxy polyester). As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of FULL Height Storage Unit with Single openable Doors : This Modular Storage Main / Add-on Unit should be knockdown in construction. All side panels, top / bottom panels, shelf panels are to be made from CRCA MS sheet, thickness ranging from 0.5 to 0.8 mm. Legs are to be fitted with screw type levelers of height 40 mm. Height wise adjustable shelf mounting, 4 shelves, load capacity of 40 Kgs UDL. The add-on units should be available for widthwise stack ability to create bank of racks, having common side panel. All steel components to be epoxy powder coated to 50 microns (+/- 10). Label holder made from clear acrylic sheet of size 155 (W) x 102(H) to be provided. Steel hinged door with self closing hinges to be provided, made from CRCA sheet of range 0.5 to 0.8 mm thickness, with three way locking arrangement. Main Unit Overall size : 500mm W x 2025mm H x 500mm D. Along with Add on Units of 1 no. 500 mm W body & 1 no. 1000 W body. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of FULL Height Storage Unit with Single openable Doors : This Modular Storage Main / Add-on Unit should be knockdown in construction. All side panels, top / bottom panels, shelf panels are to be made from CRCA MS sheet, thickness ranging from 0.5 to 0.8 mm. Legs are to be fitted with screw type levelers of height 40 mm. Height wise adjustable shelf mounting, 4 shelves, load capacity of 40 Kgs UDL. The add-on units should be available for widthwise stack ability to create bank of racks, having common side panel. All steel components to be epoxy powder coated to 50 microns (+/- 10). Label holder made from clear acrylic sheet of size 155 (W) x 102(H) to be provided. Steel hinged door with self closing hinges to be provided, made from CRCA sheet of range 0.5 to 0.8 mm thickness, with three way locking arrangement. Main Unit Overall size : 500mm W x 2025mm H x 500mm D. Along with Add on Units of 1 NO. 500 W body & 2 no. 1000 W body. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of FULL Height Storage Unit with Single openable Doors : This Modular Storage Main / Add-on Unit should be knockdown in construction. All side panels, top / bottom panels, shelf panels are to be made from CRCA MS sheet, thickness ranging from 0.5 to 0.8 mm. Legs are to be fitted with screw type levelers of height 40 mm. Height wise adjustable shelf mounting, 4 shelves, load capacity of 40 Kgs UDL. The add-on units should be available for widthwise stack ability to create bank of racks, having common side panel. All steel components to be epoxy powder coated to 50 microns (+/- 10). Label holder made from clear acrylic sheet of size 155 (W) x 102(H) to be provided. Steel hinged door with self closing hinges to be provided, made from CRCA sheet of range 0.5 to 0.8 mm thickness, with three way locking arrangement. Main Unit Overall size : 450mm W x 2025mm H x 500mm D. Along with Add on Units of 2 no. 900 W body. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of FULL Height Storage Unit with Single openable Doors : This Modular Storage Main / Add-on Unit should be knockdown in construction. All side panels, top / bottom panels, shelf panels are to be made from CRCA MS sheet, thickness ranging from 0.5 to 0.8 mm. Legs are to be fitted with screw type levelers of height 40 mm. Height wise adjustable shelf mounting, 4 shelves, load capacity of 40 Kgs UDL. The add-on units should be available for widthwise stack ability to create bank of racks, having common side panel. All steel components to be epoxy powder coated to 50 microns (+/- 10). Label holder made from clear acrylic sheet of size 155 (W) x 102(H) to be provided. Steel hinged door with self closing hinges to be provided, made from CRCA sheet of range 0.5 to 0.8 mm thickness, with three way locking arrangement. Main Unit Overall size : 500mm W x 2025mm H x 500mm D. Along with Add on Units of 1 no. 1000 W body. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of FULL Height Storage Unit with Single openable Doors : This Modular Storage Main / Add-on Unit should be knockdown in construction. All side panels, top / bottom panels, shelf panels are to be made from CRCA MS sheet, thickness ranging from 0.5 to 0.8 mm. Legs are to be fitted with screw type levelers of height 40 mm. Height wise adjustable shelf mounting, 4 shelves, load capacity of 40 Kgs UDL. The add-on units should be available for widthwise stack ability to create bank of racks, having common side panel. All steel components to be epoxy powder coated to 50 microns (+/- 10). Label holder made from clear acrylic sheet of size 155 (W) x 102(H) to be provided. Steel hinged door with self closing hinges to be provided, made from CRCA sheet of range 0.5 to 0.8 mm thickness, with three way locking arrangement. Main Unit Overall size : 450mm W x 2025mm H x 500mm D. Along with Add on Units of 1 no. 900 W body. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

roviding And Placing of Modular steel Almirah : The modular steel body almirah with Wooden doors should have base unit of size - 500 W x 2025 H x 500 D mm & Addon body of size - 500 W x 2025 H x 500 D mm.The body shall be aesthetically appealing plain, made from combination of dent resistance 0.5mm & CRCA 0.8 mm. The appealing doors should be compositely made from MDF Honeycomb and decorative laminate withwooden design finish on both sides and all edges shall be edge banded with 2mm thick PVC lipping Hanging rod shall be 1.0mm thick MS ERW oblong tube and legs should be fitted with screw type leveler. All MS sheet metal and metal frame components shall be powder coated with epoxy polyster powder to the thickness of 50-60microns. Both Base & Addon unit should consist of a lockable Drawer unit. High quality hardware should be used like screw, washer, shelf supporters, lock, Door hinges, Bumper etc. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of LIBRARY TABLE - 1200 x 900 x 750mm Providing And Placing DESK based modular workstation having Worksurface made of 25 mm thk prelam particle board with flat pvc lipping edge banding. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs, legs made up of metal powder coated finish and the entire assemply is fixed to the worktop with the help of ABS plastic spacers 20 mm high which gives the floating look to the w/s module. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of MAIN DESK 1350 x 600 x 750 mm : The Desk based modular workstation with System ht - 1200 mm UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs, legs made up of metal powder coated finish and the entire assemply is fixed to the worktop with the help of ABS plastic spacers 20 mm high which gives the floating look to the w/s module. Wire Management : Metal powder coated Cable pole of size 170mm w x 85 mm d x 705 mm ht is given to pull wires from the floor junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for accessing switches. To carry wires forward through w/s mesh type wire carrier assembly is provided below worktops. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1350 mm w x 600 mm d . As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of MAIN TABLE 1500 x 600 x 750 WITH RETURN DESK 900 X 450 X 750 mm : The Desk based modular workstation with System ht - 1200 mm UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs, legs made up of metal powder coated finish and the entire assemply is fixed to the worktop with the help of ABS plastic spacers 20 mm high which gives the floating look to the w/s module. Wire Management : Metal powder coated Cable pole of size 170mm w x 85 mm d x 705 mm ht is given to pull wires from the floor junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for accessing switches. To carry wires forward through w/s mesh type wire carrier assembly is provided below worktops. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w x 600 mm d & 900 mm w x 450 mm d. Each workstation to have one no keyboard pullout tray, CPU Trolley & Pedestal . Pedeatal shall be flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of MAIN TABLE 1500 x 750 x 750 WITH RETURN DESK 1350 X 450 X 750 mm : The Desk based modular workstation with System ht - 1200 mm UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs, legs made up of metal powder coated finish and the entire assemply is fixed to the worktop with the help of ABS plastic spacers 20 mm high which gives the floating look to the w/s module. Wire Management : Metal powder coated Cable pole of size 170mm w x 85 mm d x 705 mm ht is given to pull wires from the floor junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for accessing switches. To carry wires forward through w/s mesh type wire carrier assembly is provided below worktops. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w x 750 mm d & 1350 mm w x 450 mm d. Each workstation to have one CPU Trolley & Pedestal . Pedeatal shall be flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of MAIN TABLE 1500 x 750 x 750 WITH RETURN DESK 900 X 450 X 750 mm : The Desk based modular workstation with System ht - 1200 mm UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs, legs made up of metal powder coated finish and the entire assemply is fixed to the worktop with the help of ABS plastic spacers 20 mm high which gives the floating look to the w/s module. Wire Management : Metal powder coated Cable pole of size 170mm w x 85 mm d x 705 mm ht is given to pull wires from the floor junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for accessing switches. To carry wires forward through w/s mesh type wire carrier assembly is provided below worktops. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w x 750 mm d & 900 mm w x 450 mm d. Each workstation to have 1 no. CPU Trolley & Pedestal . Pedeatal shall be flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of MAIN TABLE 1800 x 750 x 750 WITH RETURN DESK 1350 X 450 X 750 mm : The Desk based modular workstation with System ht - 1200 mm UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs, legs made up of metal powder coated finish and the entire assemply is fixed to the worktop with the help of ABS plastic spacers 20 mm high which gives the floating look to the w/s module. Wire Management : Metal powder coated Cable pole of size 170mm w x 85 mm d x 705 mm ht is given to pull wires from the floor junction box upto the power box fixed under neath the worktop. Aluminium access flaps on worktop above power box cut out for accessing switches. To carry wires forward through w/s mesh type wire carrier assembly is provided below worktops. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w x 750 mm d & 900 mm w x 450 mm d. Each workstation to have 1 no. CPU Trolley & Pedestal . Pedeatal shall be flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of EXECUTIVE HIGH BACK CHAIR LEATHERITE. : The cushioned seat is to be made of injection molded plastic outer & inner. Plastic inner shall be upholstered with leatherette and moulded high resilience ( H R) Polyurethane foam of density 45+/-2kg/m compression. Seat Size should be 47.0 cm(W) x 48.0cm (D).The cushioned back is to be made of PU Foam with insitu molded MS E.R.WRound Tube of size 1.9+/-0.03cm x 0.16+/-0.0128cm. duely upholstered with leatherette. The High Back should be of size 47.7 cm(W) x 76.4 cm.(D). The armrest top should be moulded from polyurethane (PU) and mounted on to a drop lift adjusted type tubular armrest support made of 3.81+/-0.03cm x 0.2+/-0.01cm thk M.S E.R.W tube having chrome plated finish. The armrest height shall be adjustable up to 6.5+/0.5cm in 5 steps. Mechanism should be Active Bio - Synchro Mechanism. The adjustable tilting mechanism is to be designed with the following features:it should be 360D revolving type.Front pivot for tilt with feet resting on ground and continuous lumbar support ensuring morecomfort. Tilt Tension adjustment can be oprated in seating position. 5-position tilit limiter give option of variable tilt angle to the chair.Seat/back tilting ratio is of 1 : 2. The mechanism housing is to eb made of HPDC Aluminium black powder coated.. Seat adjustment is integrated in the seat through a sliding mechanism , Seat depth adjustment range is of 6.0+/- 0.5cm..Adjustable Back support back frame is to be connected Up/Dn mechanism housed in plastic T spine . It can be adjusted in the range of 7.42+/-0.5 cm for the comfortable back support to suit individual need. Pneumatic Ht adjustment has an adjustment stroke of 10.0+/-0.3 cm. The Pedestal ahall be of high pressure die cast polished Aluminium and fited with 5 nos. twin wheel castors. The pedestal is of 65.0 +/- 0.5cm pitch center dia (75.0+/-1.0cm with castors. The 5 bos. wheel castors shall be injestion mouldedin plastic having 6.0+0.1cm wheel diameter and assembled to pedestal. As per drawing & specification and directed by Engineer-in-Charge.Make - Godrej/ Haworth/ Herman MillarMethodex/durian or Equivalent.

Providing And Placing of MID BACK CHAIR CONFERENCE ROOM CHAIR : The cushioned seat is to be made of injection molded plastic outer & inner. Plastic inner shall be upholstered with leatherette and moulded high resilience ( H R) Polyurethane foam of density 45+/-2kg/m compression. Seat Size should be 47.0 cm(W) x 48.0cm (D).The cushioned back is to be made of PU Foam with insitu molded MS E.R.WRound Tube of size 1.9+/-0.03cm x 0.16+/-0.0128cm. duely upholstered with leatherette. The Mid Back should be of size 47.7 cm(W) x 60.1 cm.(D). The armrest top should be moulded from polyurethane (PU) and mounted on to a drop lift adjusted type tubular armrest support made of 3.81+/-0.03cm x 0.2+/-0.01cm thk M.S E.R.W tube having chrome plated finish. The armrest height shall be adjustable up to 6.5+/0.5cm in 5 steps. Mechanism should be Active Bio - Synchro Mechanism. The adjustable tilting mechanism is to be designed with the following features:it should be 360D revolving type.Front pivot for tilt with feet resting on ground and continuous lumbar support ensuring morecomfort. Tilt Tension adjustment can be oprated in seating position. 5-position tilit limiter give option of variable tilt angle to the chair.Seat/back tilting ratio is of 1 : 2. The mechanism housing is to eb made of HPDC Aluminium black powder coated.. Seat adjustment is integrated in the seat through a sliding mechanism , Seat depth adjustment range is of 6.0+/- 0.5cm..Adjustable Back support back frame is to be connected Up/Dn mechanism housed in plastic T spine . It can be adjusted in the range of 7.42+/-0.5 cm for the comfortable back support to suit individual need. Pneumatic Ht adjustment has an adjustment stroke of 10.0+/-0.3 cm. The Pedestal ahall be of high pressure die cast polished Aluminium and fited with 5 nos. twin wheel castors. The pedestal is of 65.0 +/- 0.5cm pitch center dia (75.0+/-1.0cm with castors. The 5 bos. wheel castors shall be injestion mouldedin plastic having 6.0+0.1cm wheel diameter and assembled to pedestal.As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of EXECUTIVE VISITOR FIXED CHAIR : The chair should be of size 60.9 (W) x 64.2 (D) 98.2cm cushioned seat is to be made of injection molded plastic outer & inner. Plastic inner shall be upholstered with leatherette and moulded high resilience ( H R) Polyurethane foam of density 45+/-2kg/m compression. Seat Size should be 47.0 cm(W) x 48.0cm (D).The cushioned back is to be made of PU Foam with insitu molded MS E.R.WRound Tube of size 1.9+/-0.03cm x 0.16+/-0.0128cm. duely upholstered with leatherette. Mechanism - the tubular frame shall be cantilever type & made up of 02.54+/-0.03cm x 0.2+/-0.016cm thk S.S 202 tube. The back connect to frame through chrome platedhigh pressure die cast connector piece. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of 2 Seater Peon Bench : The bench Having Seat Shell to be a welded assembly of seat, back and side frame. The Seat & Back frame is to be made up of 1.2mm thk CR steel with Oblong perforations. This is to be welded with side frame of size 32mm width x 5mm thk HR steel. The welded assembly is to be powder coated . The seat shall have have front waterfall edge to provide popliteal clearance for comfortable seating. It shall also have buttock suppport curve for comfartable sitting. SEAT Size- 47.8cm W x 44.6cm D. Back Size- 41.6cm W x 23cm H. Understucture:- Shall consist of connecting beam and leg assembly made up of MS ERW oblong tube of size 75mm x50mm x 2mm thk it shall be welded stucture assembly in powder coating which is to be fitted with shoes and levelers in nylon. Connecting beam shall be fitted with snap locking end cap. Armrest: Armrest assembly shall consist of armrest frame and armrest pad. The Armrest frame size shall be 31.7mm x 4.7mm thk HR steel and it should be powder coated. Armrest pad shall be injected moulded in Nylon and is to be fitted on armrest frame. Overall Dimensions 114.5cm W x 63.8cm D x 44.1cm SH x 78.5cm H. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of METAL KEY BOARD TRAY WITH MOUSE TRAY : Tray should be made made of 0.9 mm CRCA sheet Grade as per IS - 513. shall bof Make-Godrej or equipment of size - 350 long x 11.8mm thk Sigle extensiion 230mm ball slide should be made of combination of 1.2/1.5mmthk roll formed CRCA grade. Mouse tray of size 210 x 210 mm should be provided left or right side of tray made from 0.9 mm thk CRCA sheet As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of Pillow : Pillow should made of siliconized fibre of and cover should be of Cotton/ Poleyster fabric duely switched Size 17" X 27" As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of Single Bed QUILTED BONDED FOAM MATTRESS : The mattress should be Of size - 1981 x 914 x 100 mm.The mattress should be made of Bonded foam thickness 10 mm 18 density & the bonded is of 90 density (kg/m3). Quilting should be done on both side of mattress ,top foam quilting should be 20 mm thick of 18 density foam. Bottom foam quilting should be 20 mm thick and of 18 density foam. total thickness of mattress 160mm +/- 5mm. side boarder quilting shall be of 5mm foam of 18 desnisity,edges should to round Fabric beige of 240 (Non Wooven)Atul Textile or equipment. Guarantee should be 05 years. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of Single Seater Executive Sofa : Overall size of 860 W x 905 D x 820 H mm.With Seating Area of Width 450mm. The seat should be made up of 28 Density PU Foam +/- 2 Kg/cu.mtr with an additional top layer of super soft PU foam of 32 Desity +/- 2kg/cu.mtr and uphoslted with fabric. The back should be made up of 28 Density PU Foam +/- 2 Kg/cu.mtr with an additional top layer of super soft PU foam of 32 Desity +/- 2kg/cu.mtr and uphoslted with fabric. The under structure should be made of 120mm thick hot pressed plywood (moisture resistance & termite proof as per IS : 303) & pinewood of cross section devoide of major knots & surface defects 6 Nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. legs should be made of stainless steel (grade SS 202) tube & plate with plastic end cap. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of Three Seater Executive Sofa : Overall size of 2060 W x 905 D x 820 H mm.With Seating Area of Width 450mm. The seat should be made up of 28 Density PU Foam +/- 2 Kg/cu.mtr with an additional top layer of super soft PU foam of 32 Desity +/- 2kg/cu.mtr and uphoslted with fabric/Leatherite. The back should be made up of 28 Density PU Foam +/- 2 Kg/cu.mtr with an additional top layer of super soft PU foam of 32 Desity +/- 2kg/cu.mtr and uphoslted with fabric. The under structure should be made of 120mm thick hot pressed plywood (moisture resistance & termite proof as per IS : 303) & pinewood of cross section devoide of major knots & surface defects 6 Nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. legs should be made of stainless steel (grade SS 202) tube & plate with plastic end cap. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of Center Table : Glass Top Rectangular Center Table should be of size - 1120 W x 600 D x 351 H mm. Glass shall be 12+/- 0.3mm thick black tinted toughened glass Uvglued with bushes made in SS 202 grade for fixing with understructure.Understructure should be welded assembly made in SS202grade having Dia 12+/-0.04 asper IS : 1762. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of Corner Table : Glass Top Corner Table should be of size - 600 W x 600 D x 351 H mm. Glass shall be 12+/- 0.3mm thick black tinted toughened glass Uvglued with bushes made in SS 202 grade for fixing with understructure.Understructure should be welded assembly made in SS202grade having Dia 12+/-0.04 asper IS : 1762. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of Sofa Three Seater : The Sofa should be made of Pine Wood and 12 mm Plywood (IS-303, Commercial Plywood) frame, upholstered with PVC upholstery (1 mm thickness, Weight – GSM - 575) in black color. The Slabstock foam used has to be soft for comfort seating. Seat Foam should be32kg/m3 mm with density of 28 Kg/M3. Back Foam thickness to be 45 mm with density of 28 Kg/M3. Webbing material shall be nylone thread of 2mm Rubberwood legs to be fitted of height 50mm & 95mm dia. The three Seater Overall size: 197.0 cm (W) x 93.5 cm (D) x 92.5 cm (H) As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of 2 ARC Reception Table : Top should be in Decorative Laminate Clean matt PU finish 18mm thickInside radius 700.0mm Outside radius – 1350.0 mm Depth – 650 mm. Cork shall be Rubberized cork – 18mm thick. Glass shall be Frosted Glass 10mm thick Diamond cut finishing on edges Inside Radius – 1202.5mm Outside radius – 1402.5mm Depth – 200mm *Note: Angle sustained within arc surface should be 60 deg.Modesty Panel MS Perforated sheet Below Worksurface : 0.8 mm (thick) x 665.0 mm (height) x 1345.0 mm (flat length) Above Worksurface : 0.8mm (Thick) x 260 mm (height) x 1345.0 mm (flat length).Legs should be made of MS tube 1.6 mm thick Diameter 50.8 mm Height 604 mm. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing OF STORAGE UNIT : The HDU storage unit shall be of size 922 (W) x 750 (H) x 460 (D). Construction shall be in knockdown construction of 25mm thk and 18mm thk Pre -Laminated boards with metal cladding of 0.8mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50±10 microns thickness. TOP OPTIONS In case of 2.5feet Height Storage units, wooden top is provided which is made of 25mm thick Pre -laminated board whereas 4.0feet and 4.5feet height Storage units are provided with llmm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50±10 microns thickness.DOOR & DOOR OPENING - Single door opening for 450 & 600w units whereas two door opening for all other width options(i.e; 650 /750/800/ 900/ 950/ 1000/ 1050/ 1200W).The doors are made of 18mm thk Pre -laminated boards with decorative laminate on one side and backing laminate on the other side. SHELVING - 1) Height wise adjustible shelf mounting holes provided on side panels for easy interchange of shelf height as required. 2) Fixed shelves along with adjustible shelves provided only in case of 4.0feet & 4.5feet height units. 3) No fixed shelves for 2.5feet height storage units. 4) 1NO. adjustible shelf for 2.5feet/ 4.0feet/ 4.5feet height and 1NO. Fixed shelf for 4.0feet/ 4.5feet height without vertical partition for 450 / 600 / 650 / 750 /800 /900W whereas 2No. adjustible shelves for 2.5feet/4.0feet/ 4.5feet height and 2No. fixed shelves for 4.0feet/ 4.5feet height with vertical partition in between for 950W & above. 5) A4 SIZE BOX FILES(85Wx345Hx285D) can be stored vertically as shown in pages 4 & 5 respectively.6) Uniformly distributed load capacity for each shelf is 40Kg maximum. SKIRTING OPTION -The skirting units are provided with 150mm high skirting made of 0.8mm thick C.R.C.A (as per IS: 513) and is coated with Epoxy Polyester powder of 50±10 microns thickness. LEVELER - Screw type adjustible leveler with plastic base provides vertical adjustment for floor unevenness and leveling of units. BACK PANELS - Back panels are made of 18mm thick Pre -Laminated boards with options of Decorative laminate as well as Fabric finishes. 2.5 height units consist of single back panel whereas 4.0' height and 4.5' height units consist of split back top panel and split back bottom panel separated by an Aluminium extrusion . LOCKING MECHANISM - 3 -way nickel plated wooden furniture lock is provided for effective and positive locking of doors. HANDLE - Aesthetically appealing recessed handles of Aluminium extrusion are provided for easy opening and closing. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing OF STORAGE UNIT : The HDU storage unit shall be of size 922 (W) x 1190 (H) x 460 (D). Construction shall be in knockdown construction of 25mm thk and 18mm thk Pre -Laminated boards with metal cladding of 0.8mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50±10 microns thickness. TOP OPTIONS In case of 2.5feet Height Storage units, wooden top is provided which is made of 25mm thick Pre -laminated board whereas 4.0feet and 4.5feet height Storage units are provided with llmm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50±10 microns thickness.DOOR & DOOR OPENING - Single door opening for 450 & 600w units whereas two door opening for all other width options(i.e; 650 /750/800/ 900/ 950/ 1000/ 1050/ 1200W).The doors are made of 18mm thk Pre -laminated boards with decorative laminate on one side and backing laminate on the other side. SHELVING - 1) Height wise adjustible shelf mounting holes provided on side panels for easy interchange of shelf height as required. 2) Fixed shelves along with adjustible shelves provided only in case of 4.0feet & 4.5feet height units. 3) No fixed shelves for 2.5feet height storage units. 4) 1NO. adjustible shelf for 2.5feet/ 4.0feet/ 4.5feet height and 1NO. Fixed shelf for 4.0feet/ 4.5feet height without vertical partition for 450 / 600 / 650 / 750 /800 /900W whereas 2No. adjustible shelves for 2.5feet/4.0feet/ 4.5feet height and 2No. fixed shelves for 4.0feet/ 4.5feet height with vertical partition in between for 950W & above. 5) A4 SIZE BOX FILES(85Wx345Hx285D) can be stored vertically as shown in pages 4 & 5 respectively.6) Uniformly distributed load capacity for each shelf is 40Kg maximum. SKIRTING OPTION -The skirting units are provided with 150mm high skirting made of 0.8mm thick C.R.C.A (as per IS: 513) and is coated with Epoxy Polyester powder of 50±10 microns thickness. LEVELER - Screw type adjustible leveler with plastic base provides vertical adjustment for floor unevenness and leveling of units. BACK PANELS - Back panels are made of 18mm thick Pre -Laminated boards with options of Decorative laminate as well as Fabric finishes. 2.5 height units consist of single back panel whereas 4.0' height and 4.5' height units consist of split back top panel and split back bottom panel separated by an Aluminium extrusion . LOCKING MECHANISM - 3 -way nickel plated wooden furniture lock is provided for effective and positive locking of doors. HANDLE - Aesthetically appealing recessed handles of Aluminium extrusion are provided for easy opening and closing. As per drawing & specification and directed by Engineer-in-Charge.Make - Knoll/Godrej/ Haworth/ Steelcase/ Herman Millar or Equivalent.

Providing And Placing of Slotted Angle Rack : The Slotted Angle racks should be of size - 1829H x 905W x 448D mm having 6 shelves with 6 bend Panel 1mm thick. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of 18 SEATER Conference Table : The modular Conference Table should have Top thickness 31.6 (18mm + 12mm + 0.6 mm DL(both sides) + 0.4mm Membrane) Edge profile Waterfall Edge 10mm radius on top edge and 5mm at bottom.Single seater 760 W x 600 D, Two seater 1360 W x 600 D Half Round (2 Seater) R 713, Quarter Round (1 Seater) R 713. Legs Made from 25mm PPB having a straight profile with half round edges and clad with 0.6mm thick Post Forming laminate. Overall thickness of leg is 26.2mm. Modesty Panel Made from PLT (Prelaminated Twin) boards of 18mm thick. Wire carrier Made from 0.6mm thick CRCA painted. Wire cover Made of 12mm thk. MDF Painted all over, Substrate MDF. Skin PVC Membrane foil (0.4mm thk) clad on the substrate MDF using PU glue for better adhesion. This foil is pre-coated with layer of polyurethane for better scratch resistance.Sizes to be as per the site measurements and layout. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing OF STORAGE UNIT : It should have multi bend construction with interlocking design and full length over lapping doors and sides. It should have three way bolting mechanism. All steel components should undergo eight tank anti rust treatment and oven baked epoxy polyester powder coated with 50-60 dry film thickness. The CRCA steel sheet used for the body is of 20 SWG / guage, as per IS-513 1994. It has 5 shelves made of 22 SWG / guage CRCA steel sheet. It has six lever Mazak Zinc Plated Godrej or equipment Lock. It has scratch hardness of 3 Kgs as BS-3900 part E2 1970, IS-101. It sustains salt spray test of 1000 hrs. as per IS 101. It should have 4 shelves made of 0.8 mm thick CRCA steel sheet. It should have six lever Mazak Zinc Plated Godrej or equipment Lock. It should sustain salt spray test of 1000 hrs. as per IS 101. Overall size: 198.0 cm (H) x 91.5 cm (W) x 48.5S cm (D). As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of Office Table : The table is of size 1365 mm (W) x 680 mm (D) x 735 mm (H). The top of table is to be made of 18 mm thick pre-laminated plain particle board. All the edges of the top are duly sealed using 2 mm thick Doelleken beading, fixed by using Jowart/ Klibert glue. Understructure is made in form of ‘C’ frame made of 0.9 mm thk. powder coated CRCA MS Sheet o. The tubular frame is to be made of MS ERW round tubes dia 25.4 mm x 1.2 mm thk. Drawer Unit (Three Drawer + Two Drawer unit) : The shell of the drawer unit is to be made of 0.8 mm thick CRCA MS sheet. The drawer tray is made of 0.6 mm thick CRCA sheet and the drawer front is made of 0.8 mm thick CRCA sheet. Drawer slides are based on friction slides of 1.2 mm thick CRCA sheet. It should have 6 lever brass lock. The handles of drawer are made of ABS plastic.As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of VISITOR CHAIR FIXED : The chair should be of size 60.9 (W) x 64.3 (D) 99.5cm cushioned seat is to be made of injection molded plastic outer & inner. Plastic inner shall be upholstered with leatherette and moulded high resilience ( H R) Polyurethane foam of density 45+/-2kg/m compression. Seat Size should be 47.0 cm(W) x 48.0cm (D).The cushioned back is to be made of PU Foam with insitu molded MS E.R.WRound Tube of size 1.9+/-0.03cm x 0.16+/-0.0128cm. duely upholstered with leatherette. Mechanism - the tubular frame shall be cantilever type & made up of 02.54+/-0.03cm x 0.2+/-0.016cm thk S.S 202 tube. The back connect to frame through powder coated (DFT 40 -60 microns) high pressure die cast connector piece. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of full Height Sliding Door Storage Unit : The Full Height Sliding Door Storage Unit should be of size 1830 x 900 x 450 mm It should have Rigid Knock-down construction with press fit riveted design, made from 0.8 mm Prime Quality CRCA steel. Two sliding doors should be provided. It should have snap on type aesthetically appealing die cast 5 lever cam lock and plastic flush recessed handles. Full height sliding doors with top hanging arrangement to prevent derailment and 2 plastic rollers having steel ball bearings. The shelves should be height wise adjustable, with UDL capacity of 80 Kgs. for full length and 40 Kgs. for half shelf. The top should be made of 25 mm thick PLB with 2 mm thick PVC edge banding. .All steel components should undergo eight tank anti rust treatment and oven baked epoxy polyester powder coated with 50 microns dry film thickness. The CRCA steel sheet used should be 0.6 mm thick as per IS-513 1994. It should have scratch hardness of 3 Kgs as BS-3900 part E2 1970, IS-101. It should sustain salt spray test of 1000 hrs. as IS 101. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of Media Unit : The media unit should be of size 1200 Wx 398 D x 500 H mm. All the body panels should be made of 18mm thick plelaminated particle board IS : 12823 Class E1,all exposed deges are to be edge banded with 2 mm thick PVC edge banding glue with hot melt EVA glue. Drawers are to be made of 18 mm thick prelaminated particle board IS 12823 high quality hardware to be used like KD fittings, wooden dowels is of Hettich make. 18 mm particle board shall be in CINCINNATI WALNUT Shade. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of RECTANGULAR WORKSTATION / Linear Workstation of Size: 900mm(W) x 600mm(D) with 3 Drawer Metal Pedestal , keyboard and cpu trolley : Supply of workstations in panel based modular partition system of 1200mm Height And overall thickness shall be 52.4mm. Bottom tiles should be metal/laminate, intermediate blocks laminated and two tiles should be fabric. panel should be comprise of 2 nos. of vertical extrusions made of aluminum. Horizontal extrusions shall be made of aluminum at every division of tile/block. The numbers of these horizontal extrusions should be four. A block panel's thickness shall comprise of 38mm thick paper honeycomb, plus 3mm MDF on each sides and 0.6mm decorative laminate or fabric on both sides. Numbers of these blocks shall vary as per panel height.1 number of fabricated bottom frame as a welded structure of steel components. 2 nos. of bottom tiles. 2 nos. of top tiles. 1 no. of top trim shall be made of aluminum extrusion. These panels shall be supported on legs with leveler at various locations depending on the layout requirements for better Air circulation in the area. Panel legs shall be fabricated by CO2 welded MS Tube of section 38 mm x25 mm (IS: 7138 ERW Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler is fitted. coated with average 50 to 60 micron thicknedd of epoxy powder coating. fabricated bottom frame for 52.4 mm panel comprises of L channels made of 2 mm thick CRCA steel , formed plates of 3 mm thick HR steel & ERW steel tube of size 35X15X1.6 mm thick in oval cross section welded together. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of RECTANGULAR WORKSTATION / Linear Workstation of Size: 750mm(W) x 600mm(D) with 3 Drawer Metal Pedestal , keyboard and cpu trolley : Supply of workstations in panel based modular partition system of 1200mm Height And overall thickness shall be 52.4mm. Bottom tiles should be metal/laminate, intermediate blocks laminated and two tiles should be fabric. panel should be comprise of 2 nos. of vertical extrusions made of aluminum. Horizontal extrusions shall be made of aluminum at every division of tile/block. The numbers of these horizontal extrusions should be four. A block panel's thickness shall comprise of 38mm thick paper honeycomb, plus 3mm MDF on each sides and 0.6mm decorative laminate or fabric on both sides. Numbers of these blocks shall vary as per panel height.1 number of fabricated bottom frame as a welded structure of steel components. 2 nos. of bottom tiles. 2 nos. of top tiles. 1 no. of top trim shall be made of aluminum extrusion. These panels shall be supported on legs with leveler at various locations depending on the layout requirements for better Air circulation in the area. Panel legs shall be fabricated by CO2 welded MS Tube of section 38 mm x25 mm (IS: 7138 ERW Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler is fitted. coated with average 50 to 60 micron thicknedd of epoxy powder coating. fabricated bottom frame for 52.4 mm panel comprises of L channels made of 2 mm thick CRCA steel , formed plates of 3 mm thick HR steel & ERW steel tube of size 35X15X1.6 mm thick in oval cross section welded together. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of PENTAGONAL Workstation of size- 1350mm(W1) x 600mm(D1) X 1200mm(W2) x 600mm(D2) X 750mm(H) with pedestal , keyboard and cpu trolley : Supply of Workstations in Panel based modular Partition system of 1200mm HEIGHT And overall thickness shall be 52.4mm. Bottom tiles should be metal, intermediate blocks laminated and two tiles should be fabric. panel should be comprise of 2 nos. of vertical extrusions made of aluminum. Horizontal extrusions shall be made of aluminum at every division of tile/block. The numbers of these horizontal extrusions should be four. A block panel's thickness shall comprise of 38mm thick paper honeycomb, plus 3mm MDF on each sides and 0.6mm decorative laminate or fabric on both sides. Numbers of these blocks shall vary as per panel height.1 number of fabricated bottom frame as a welded structure of steel components. 2 nos. of bottom tiles. 2 nos. of top tiles. 1 no. of top trim shall be made of aluminum extrusion. These panels shall be supported on legs with leveler at various locations depending on the layout requirements for better Air circulation in the area. Panel legs shall be fabricated by CO2 welded MS Tube of section 38 mm x25 mm (IS: 7138 ERW Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler is fitted. coated with average 50 to 60 micron thicknedd of epoxy powder coating. fabricated bottom frame for 52.4 mm panel comprises of L channels made of 2 mm thick CRCA steel , formed plates of 3 mm thick HR steel & ERW steel tube of size 35X15X1.6 mm thick in oval cross section welded together.Finish: coated with average 50 to 60 micron thicknedd of epoxy powder coating.Work surface shall be made up of 25 mm Pre Laminated finishes. It should be finished with PVC edge bending. The work surface shall be provided with circular cut out of Dia.65mm. Work surface mounted with help of bracket and holder bracket. work surface bracket mounted on to the horizontal extrusion. it is made from 2.0 mm thick CRCA grade D sheet. all the work surface mounted on the brackets through round phillip head diameter 4 mm X 19 length having finish zinc plate. holder bracket made from 2.0 mm thick CRCA grade D sheet. it is slid in between end trim & vertical extrusion & mounted on work surface bracket with the help of pop rivet.for passing of wires. These cut outs shall be provided with ABS covers. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of PENTAGONAL Workstation of size- 1350mm(W1) x 600mm(D1) X 1350mm(W2) x 600mm(D2) X 750mm(H) with pedestal , keyboard and cpu trolley : Supply of Workstations in Panel based modular Partition system of 1200mm HEIGHT And overall thickness shall be 52.4mm. Bottom tiles should be metal, intermediate blocks laminated and two tiles should be fabric. panel should be comprise of 2 nos. of vertical extrusions made of aluminum. Horizontal extrusions shall be made of aluminum at every division of tile/block. The numbers of these horizontal extrusions should be four. A block panel's thickness shall comprise of 38mm thick paper honeycomb, plus 3mm MDF on each sides and 0.6mm decorative laminate or fabric on both sides. Numbers of these blocks shall vary as per panel height.1 number of fabricated bottom frame as a welded structure of steel components. 2 nos. of bottom tiles. 2 nos. of top tiles. 1 no. of top trim shall be made of aluminum extrusion. These panels shall be supported on legs with leveler at various locations depending on the layout requirements for better Air circulation in the area. Panel legs shall be fabricated by CO2 welded MS Tube of section 38 mm x25 mm (IS: 7138 ERW Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler is fitted. coated with average 50 to 60 micron thicknedd of epoxy powder coating. fabricated bottom frame for 52.4 mm panel comprises of L channels made of 2 mm thick CRCA steel , formed plates of 3 mm thick HR steel & ERW steel tube of size 35X15X1.6 mm thick in oval cross section welded together.Finish: coated with average 50 to 60 micron thicknedd of epoxy powder coating.Work surface shall be made up of 25 mm Pre Laminated finishes. It should be finished with PVC edge bending. The work surface shall be provided with circular cut out of Dia.65mm. Work surface mounted with help of bracket and holder bracket. work surface bracket mounted on to the horizontal extrusion. it is made from 2.0 mm thick CRCA grade D sheet. all the work surface mounted on the brackets through round phillip head diameter 4 mm X 19 length having finish zinc plate. holder bracket made from 2.0 mm thick CRCA grade D sheet. it is slid in between end trim & vertical extrusion & mounted on work surface bracket with the help of pop rivet.for passing of wires. These cut outs shall be provided with ABS covers. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of Faculty Table : The premium wooden desk which comprises of Work Top , side panels and modesty panels and a free standing padestal. The dimension of the table should be 1500mm (L) X 750mm (W) X 740mm (D). The entire desk unit should be assembled with a suitable knock down fitings and hardware also each side panel shall be provided with cutout or laying cables for the moniter and other computer accessories. The worktop and side panel should be made rom 25 mm thick prelaminated partical board and the edges must be sealed with 2 mm thick PVC edge band all around. the side panel should have two glide screws each for labeling of the desk. Modesty panel must be made from 18 mm thick prelaminated partical board with edges sealed upto 0.8 mm thick PVC edge band all around. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of Optimizer : The Single Bay Optimiser should consist of Main Body: Rigid Knock Down construction made out of 0.8 thk. CRCA Steel conforming to IS: 513 Gr.D. Each body block (SS/SL/TM) building to consist of 1 Main unit & then Add-on units (0, 1,2,3,4 - depending on no. of bays 1, 2, 3, 4 & 5). Each unit to have 5 loading levels formed by 4 nos. adjustable shelves. Body units are bolted to undercarriage. Height from ground is 2080 mm (1980 body + 65 undercarriage + 35 channel Finish : The bodies including shelves should be given antirust surface treatment & to be powder coated with epoxy polyester powder, involving an 8 step treatment consisting of Hot water rinse, Knock of degreasing, degreasing, cold water rinse, phosphating, cold water rinse, and passivation & dry off oven treatment. Final finish consists of epoxy polyester powder coating of approved color & shade with a Dry Film Thickness of minimum 40 microns. The testing of paint to be done for various physical & chemical properties as per IS: 101. The material to be then oven baked with a controlled temperature of 180 deg.C to 200 deg.C. Shelf: To be made of 0.8 thk CRCA steel conforming to IS: 513 Gr.D or DD. Its max load bearing capacity to be 80 Kg uniformly distributed per shelf for P1 Type of Configuration. Shelves to be mounted on support brackets & shelf level should be adjustable at approx. 25.4 pitches. There should be 4 adjustable shelves per body giving 5 loading levels, if no Cradle pair is provided. Undercarriage: The Undercarriage to be a welded frame made of HR sheet 3.15 mm thk conforming to IS:10748 suitably fabricated to take the loads based on configuration. The undercarriage, after pre-treatment, to be coated with final finish consisting of epoxy polyester powder coat of approved color & shade with a Dry Film Thickness of minimum 40 microns. Centralized Locking : Centralized locking arrangement to be provided through Locking Stiffener mounted onto back of the Last unit so that it gets locked on channels when all the units are brought together. The Recess handle lock to be of Godrej or equipment make & placed at suitable height. The arrangement should not occupy space more than 90.0 mm. Each Drive type units have Locking Knob near the Drive wheel for manual locking of individual units when a person is using those units. Knob shall be rotated to unlock position when units are to be moved. After the unit is moved, before entering into aisle for accessing, this knob shall be rotated to lock position. End stoppers to be provided at the end of channels to prevent derailment. Door Locking / handle: Hinged doors to have Recessed Die cast Handle cum lock giving 3 way locking through a lever & shooting bolts. While Sliding doors should have a die cast lock & separate plastic snap-on handles. Guide Channels consisting of ‘J’ section 2 mm thk HR sheet & 25 mm Square bright bar – both connected by screws. Label Holder to be made from 2 mm thk clear transparent Acrylic sheet & having outer dimension of 155 mm X 106 mm All the nuts & bolts to be galvanized / blackodized / Zn Plated. The Push Pull Type Single Bay Optimiser set should contain 1 no. SL Body of Size - 915mmW x 457mmD x 2080H mm, 1 no. SS Body of Size - 915mmW x 457mmD x 2080H mm, 2 no. TD of Size - 915mmW x 762mmD x 2080H mm. with 15 Feet Length Channels. Design as per Layout. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Providing And Placing of Training room chair with desklet & Arms: SEAT / BACK: The seat sub-assembly is made up of 1.2±0.1cm thk Plywood measured as per QA method described in OCP-QLTA-P14-18 upholstered with moulded foam and polyester fabric and covered with an injection-moulded polypropylene outer cover. The seat can tip-up when not in use and this feature can be used while, cking the chairs horizontally. The back sub-assembly is made up of injection-moulded, inner upholstered with moulded foam and polyester fabric and covered with an injection-moulded polypropylene outer cover. The contoured back with width extension at the bottom area is designed to give comfort to lower back. The back flexing features allows the back to tilt by 9°±2° to aid the user in adopting a comfortable reclining posture. Both these sub-assemblies are fixed to the tubular structure. BACK SIZE: 45 .2cm (W) X 44.6cm (H) SEAT SIZE: ,47.0cm (W) X 50.0cm (D) TUBULAR FRAME STRUCTURE: The powder-coated 4 leg structure is made of 2.2 ±0.03cm dia x 0.25 ±0.02cm thk M.S. E.R,W. Tube front and rear leg welded along with connecting tube made of 1.9 ±0.02cm dia x 0.2 ±0.016cA1 thk` M.S. E.R.W. Tube to form the tubular frame assembly. The legs are provided with injection-moulded adopter bush in black Nylon and brake-loaded castors enabling easy maneuvering while not in use and stable sitting while in use. The chairs can be stacked horizontally when not in use. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 70 ±8 kg/m3 and Hardness load for Seat 16 ± 2 kgf and Hardness load for back 12 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The armrest structure is made up of 2.2 ±0.03cm dia x 0.25 ±0.02cm thk M.S. E.R.W. Tube welded to the Tubular Frame structure and having a scratch-resistant ABS Arm top. FULL DESKLET: The Full Desklet assembly is Flip-up type and is made up of extension tube of 1.9 ±0.02cm dia x 0.2 ±0.016cm thk M.S. E.R.W. Tube and a support tube on L.H. side of 1.6 ±0.02cm dia x 0.2 ±0.016cm thk M.S. E.R.W. Tube on which an scratch resistant ABS desklet top is fixed and covered on bottom side with a bottom cover. BRAKE-LOADED CASTORS: The brake-loaded castors are assembled to the chair legs, to give a free movement for maneuvering the chair when not in use and it will brake the movement when load is applied (while in use) to give a stable feel. The twin wheel castors are injection molded in black Polypropylene. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black Nylon +30% GF. As per drawing & specification and directed by Engineer-in-Charge.Make -Godrej/ Haworth/Herman Millar/Wipro/Methodex/durian or Equivalent.

Twenty First Century Techno Products Pvt. Ltd.

ADARSH INFRAINTERIO PVT LTD