PROVISION OF SECURITY GATE AND ADDN/ ALTN AND IMPROVEMENT OF MAIN GATE HARD STANDING FOR GUARD UNDER GE GOLCONDA

M&L PCC 1:4:8 Type D2 (40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed

M&L brick work with sub class `B' bricks straight or curved on plan exc. 6 m mean radius built in CM 1:6 complete all as specified and directed

M&L RCC M-25 design mix (20 mm graded stone aggregate) as in foundations and including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, and mass concrete complete all as specified and directed.

(a) Aluminium busbar 200 amps - 04 Nos, supported on suitable size of heavy duty porcelein stand lock with suitable size of brass nut, bolts and washer with heat shrinkable PVC sleeving. The bar shall be colour coded (red, yellow and blue) for three phases and black for neutral. (b) MCCB 63 amps, 415 volt, 16 KA breaking capacity 4 pole electromagnetic release duly connected to busbar as incoming - 01 No.

All as per Sl. Item No. 5 above but in columns.

All as per Sl. Item No. 5 above but in beams, cantilevers, bressummers, lintels over 1.5 m span.

M&L mild steel bars (TMT bars) 10 mm dia and over cut to length, bent to shape required and including cranking, bending, spirally for hoping for columns, hooking ends and binding with and including mild steel wire not less than 0.9 mm dia complete all as specified and directed.

All as per Sl. Item No. 11 above but 6 mm to 8 mm dia as in stirrups.

M&L form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for fair finished surfaces complete all as specified and directed.

M&L form work to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surfaces complete all as specified and directed

M&L form work to sides and soffits of floor or roof beams, beam haunchings, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc, for fair finished surfaces .complete all as specified and directed.

M&L form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (horizontal or sloping) for fair finished surfaces complete all as specified and directed.

M&L Dholpur stone with hammer dressed facework (with maximum depression from a straight edge held against the dressed surface not exc. 20 mm), about 40 mm high, 75 mm deep in straight courses, laid and jointed in cement and stone dust mortar 1:3, recess pointed (10 mm x 20 mm) with an admixture of white cement and Dholpur stone dust 1:1 as in vertical surfaces etc. upto a height of 10 m to match over & including 10 mm thick rendering in CM 1:4 and taking down complete all as specified and directed.

S&F monier elabana concrete tile and including ridge tiles orange or any colour size, 430 mm x 330 mm, each tiles with 10 years warranty for colour installtion services fixing monier roof tiles on to provided plastered slabs with necessary cement purlins, placed at 13 inch c/c in which first purlin will be placed at a distance of 11 inch with double purlin height. Followed by monier roof laying from the bottom of the roof with a maximum overlap of 75 mm -100 mm followed by fixing of ridge tile, hip starter and 4 way supported by elevated shs / rhs section with an underlay of topflex strip & finally the ridges to be fixed with tile clip as per manufacturers instructions complete all as specified and directed.

S&F powder coated (minimum thickness of powder coating 50 micron) aluminium anodised frame for doors, windows, ventilators with one or more rebates and including joining cleat for fixing, etc, complete all as specified and directed.

M&L 12 mm thick pre-laminated, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed to aluminium frame complete all as specified and directed.

S&F double rebate windows made of pre-painted steel (base steel as per IS 513 of 0.58 mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM) and including primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72 x 55 mm, centre mullion should be of 72 x 50 mm, section for fixed glass beading should be of 12 x12 mm and section for shutter should be of 52 x 25 mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20 x 40 mm.

The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2 nos. of heavy duty stain less steel pivot hinges shall be provided per shutter. The windows should be paneled with 5 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws. Including 10 mm square guard bars with 6” (152.4 mm) pitch, complete for finished item of work including taking down existing steel windows and making good disturbed surfaces all as specified and directed.

M&L 15 mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed

M&L applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm / litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces over 1.5 mm thick wall care putty complete all as specified and directed.

Demolition of brickwork or stone / boulder masonry / Block masonry, built in cement mortar including facing, dressed stone work and precast concrete all quoins, arches, pillars, coping etc but excluding ashlars articles complete all as specified and directed

M&L framed work as in doors and gates of angle or other section with gusset plates, rails, braces, etc, complete, drilled for fixing of steel sheeting or other covering, doors etc, to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to Fe-410 or Fe-310 and including dismantling complete all as specified and directed.

M&L bituminous premixed semi-dense asphaltic concrete 30 mm consolidated thickness with 5.5% binder content using paving bitumen of grade VG-30 penetration by weight of total mix laid using mechanical paver, rolled and compacted to required gradient and camber using power roller of capacity exc. 8 tonne but not exc. 12 tonne and including preparing existing black top surfaces by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surface with gunny bag to remove loose dirts and applying evenly a priming / tack coat with bitumen primer at 5 Kg per 10 Sqm using paving bitumen over existing black top surfaces complete all as specified and directed.

Note: For design purpose min. binder content is specified as 5.5% for VG-30 grade bitumen and it shall not reduce under any circumstances. During design stage, if binder content exceeds 5.5% no extra payment shall be made to contractor for excess use of binder.

M&L premix bituminous macadam with bitumen content 4% total weight of mix laid rolled and compacted to required gradient and camber using paving bitumen consolidated thickness less than 75 mm complete all as specified and directed

M&L point wiring for one light / fan point controlled by one switch complete all as specified with 1100 Volts grade 1.5 Sqmm PVC insulated FR-LSH unsheathed cable with multistranded copper conductor conforming to IS:694:1990 with ISI marking in and including PVC rigid conduit medium grade of size minimum 20 mm with all accessories concealed in wall / ceilling, continous earth wire 1.5 Sqmm PVC insulated FR-LSH unsheathed 1100 Volts multistanderd copper conductor connected to common earth and dolly, necessary modular metal flush boxes concealed in walls and modular white plate covers with frame for mounting for modular switches / sockets / fan regulators etc, for one light point controlled by one switch one way complete all as specified and directed.

Note: Cost of cutting chases in walls and making good for concealed wiring and cost of modular boxes with cover plates is deemed to be included in the quoted rate.

S&F ceiling rose three terminal surface bakelite type AC 50 Hz 230 Volts of size 65 x 50 mm complete all as specified and directed.

S&F modular switch 1 way 6A, 1 module complete all as specified and directed.

S&F modular socket, shuttered type, 6A - 3 pin 2 module complete all as specified and directed.

S&F modular switch 1 way 16A with indicator, 1 module complete all as specified and directed.

S&F modular socket, shuttered type, 6/16A, combined 2 module complete all as specified and directed.

hing to body of equipment /DBs, GI wire protected by 15 mm dia light grade GI pipe upto connecting point and watering arrangements with 20 mm dia GI pipe medium grade and GI funnel all as specified and shown in electrical plate No. 3. of MES Schedule (SSR) Part I complete all as specified and directed.

Excavating in trenches, n. exc. 1.5 m wide and n. exc. 1.5 m in depth for foundation, laying of cables etc, n. exc. 10 sq m on plan and n. ex.c 1.5 m in depth and getting out in soft / loose soil complete all as specified and directed.

hing to body of equipment /DBs, GI wire protected by 15 mm dia light grade GI pipe upto connecting point and watering arrangements with 20 mm dia GI pipe medium grade and GI funnel all as specified and shown in electrical plate No. 3. of MES Schedule (SSR) Part I complete all as specified and directed.

Supply, install, test and commission CPRI aproved factory fabricated, outdoor type, LTfeeder pillar box made out of 3.15 mm thick CRCA sheet of size 1 M x 0.75 M x 0.35 M with projected globe roof for rainwater protection dust and vermin proof, double door with both side opening and including neoprene rubber gasket, suitable for 440 Volt 3 Phase 4 Wire System, including danger plate, earthing strip point and ventilation louvers at rear side, bottom detachable gland plate with suitable size zinc cromium plated nuts, bolts and washers etc. and embeded with 50x50x6mm MS angle iron frame, 600 mm above the normal ground level with internal connection with suitable size of cable, cable lugs and cable glands, necessary PCC foundation in cement concrete 1:3:6 (20 mm graded stone aggregate) complete all as specified and directed comprising of the following :-