8654/GWL/E8 SPECIAL REPAIR TO BLDG NO P-47 AND PROVN OF CERTAIN MINOR WORKS AT MORAR CANTT GWALIOR

Amount

Taking down chowkhat or frame (without taking off shutter from the frame) not exceeding 1.5 Square Metre each , removing from the site Cutting holes exc 150 Sq.cm but n.exc 400 Sq.cm in super facia area into or through brick walls built in mud mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required complete all as specified and as directed.

Taking down chowkhat or frame (without taking off shutter from the frame) exceeding 1.5 sqm and not exc 4.00 sqm each , removing from the site Cutting holes exc 150 Sq.cm but n.exc 400 Sq.cm in super facia area into or through brick walls built in mud mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required complete all as specified and as directed.

S&F solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and as directed.

S&F aluminum handles cast type, anodized of 100 mm size complete all as specified and directed.

S&F stainless steel hinges 100mm long medium weight, cold rolled mild steel complete all as specified and directed.

S&F 100 mm long aluminium anodised , barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F MS Pressed steel frames for doors with one or more redates including necessary fixing lugs hinges lock strike plate etc complete as specified abd size of frame 105x60mm complete.note : cost of filling of PCC (1:3:6) type C-0 in hollow portion of frame id deemed included in these items .

M & L for factory made 35 mm 2nd class Hard Wood, plain framed factory made panelled shutters ( two panel) with lock rail and panel of 9mm B.W.R grade ply or 12mm MDF board exterier grade medium density, wood particle board with commercial veneering on both face IS 1003 ( Part-I) kiln seasoned and chemically pressured treated including preparation of the surfaces and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors , windows , ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium door shutters of aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing, powder coated aluminium handles 150mm size 2 Nos, 3 Nos powder coated aluminium hinges heavy duty and 02 Nos 150mm long powder coated aluminium tower bolts in each door shutter with powder coated aluminum snap beading, screws etc. complete all as specified and directed Note : Panel filling ie. glass, fibre sheet, board etc. shall be measure and paid for separately.

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium window and ventilator shutters side hung type without sash, aluminium section weighing 0.55 kg/m including joining cleats, glazing clips, rubber neoprene packing, necessary powder coated hardware ie. handles, barrel tower bolts, hinges etc, powder coated aluminum snap beading, screws etc. complete all as specified and directed Note : Panel filling ie. glass, fibre sheet, board, wire mesh etc. shall be measured and paid for separately.

S & F for door closer hydraulically regulated, designation No. 3, universal type, aluminium die-cast body (ISI Marked), suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed in repair complete all as specified and directed

S & F of double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in repair complete all as specified and directed

S&F MS Sliding door bolts Rod pattern stove enamelled black with bolts not less than 12mm dia with and including a minimum of 6 bolt and nuts four on bolt plate and two on staple plate of 250mm size complete.

S&F 150 mm long aluminium anodised , barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F butt hinges 100mm long medium weight, cold rolled mild steel.

S&F aluminum handles cast type, anodized of 150 mm size complete all as specified and directed.

Taking down existing tarfelt from roof and removing from site all as directed.

M&L for 10 mm thick rendering in CM (1:4) over roof ,surface finished even and Smooth mixed with water proofing compond complete all as speceified and as directed by engineer- in charge . Note : Water proofing compound shall be measured and paid separately under appropriate item of BOQ as "supply only "

M &L For applying water proofing treatment with the following coats :- (a) First coat of bitumen primer conforming to IS -3384 @ 0.3 Kg/sqm (b) Second Layer of APP based polymectric membrane minimum weighing 3kg /sqm and minimum 3 mm thick reinforced with polyster non woven fabric land on primed surface by torch application (c) third two coat of aluminium bituminous paint ( 200ml/sqm i.e. 100ml/sqm in each layer ) over polymetric membrane complete all as specified and as directed.

Supply only Liquid water proofing compound complete.

Demolition of cement concrete of any description and in any position (unreinforced not otherwise specially provided for complete all as specified and directed.

M & L PCC (1:2:4) Type Bo using 12.5 mm graded stone aggregate as levelling course/mass concrete complete all as spd and directed.

M & L PCC (1:2:4) Type Bo using 12.5 mm graded stone aggregate pan, cills, steps; seismic and other similar bands,plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height,copings, kneelers, apex stones, bed plates, kerbs not provided for in water troughs and the like including weathering, slightly rounded or chamfered angle complete all as spd and directed.

M & L for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete.

Demolition of wall and ceiling boards fibre pulp insulation etc or insulation boards/slabs/blankets any thickness including cover fillets, complete all as specified and directed.

S&F E- grid False ceiling 4 mm thick HPSC pre-prime non asbestos fibre cement building board (E-classic size 600mm x 600 mm/ 595 mm x595 mm ) decorative finish fixed with clips and screw including powder coated galvanised MS grid frame work false ceiling of ( Main Tee size 38mmx24mmx0.65mm cross tee 24mmx24mmx0.45mm ) and with slot for fixing including suspended with 2mm dia. GI wire hangers fixed with steel dash through fasteners from purline of the roof complete all as specified and as directed.

Dismantling of wrought iron or mild steel work of any description not other wise provided for complete all as specified and as directed.

S&F rolled section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates confirming to Fe-290 ( Gde E-165) complete all as specified and directed

Dismantiling of stone slabs and tiles (Kota stone etc.) of any discription or any thickness in floors, aprons, skirting, dado, pcc tiles at roof etc. laid bedded and pointed in any mortar complete all as specified and directed.

M&L for Moorum red bajri filling in floor or paving laid in layers n. exc. 15cm thick spread levelled and rammed including watering complete all as specified and directed.

M&L PCC Type D2 (1:4:8) using 40mm graded stone agg as in foundation filling mass concrete complete.

M&L for machine cut Kota stone slab 20mm to 25 mm thick , as in flooring , laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing , over and including screed bed or bedding layer of mortar 20 mm thick in cement mortar (1:3) complete all as specified and directed.

M&L for machine cut kota stone slab 20mm -25 mm thick as in riser / steps, skirting, dado,cills and pillars laid and jointed with grey cement slurry mixed with pigment to match with the shade of the slab including rubbing and polishing over and including 10 mm thick backing coat in CM (1:3) complete all as specified and directed.

M&L for vitrified ,coloured and printed tiles of 9 to 10 mm thick (Square / Rectangular ) polished area of each tiles not exceeding 0.36 Sqm as in flooring over and including 15 mm thick cement screed in (1:4) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.

M&L for vitrified ,coloured and printed tiles of width as directed and 9 to 10 mm thick as in skirting fixed over and including 10 mm thick cement screed in (1:3) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.

M&L for non skid ceramic Coloured joint free tiles, 300mmx300mmx 7 mm to 8 mm thick, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match with the colour of tiles, over and including 15 mm thick screed bed or bedding layer of cement mortar( 1:4) complete all as specified and directed.

M&L for digital glazed ceramic tiles joint free, coloured tiles 300mm x 450mm x 7 to 8 mm thick on vertical faces ie. as in skirting/dado etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles fix over and including 10 mm thick backing coat in cement mortar (1:3) complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls etc. including racking out joints hacking for key scrubbing down with water etc.complete.

M&L for rendering 10 mm thick in CM (1:4) on brick work or conrete surfaces/stone masonary and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar on fair faces of brick work or concrete surfaces , applied in two layers ie. Ist layer of 10 mm thick rendering in cement mortar (1:6 ) and 2nd ( top ) layer of 5 mm thick rendering in cement mortar (1:4 ) and top layer mixed with water proofing compound as per manufacturer's instruction & finished even and smooth without using extra cement complete all as specified and directed. (Note:- Water proofing compound shall be measured and paid seperately under appropriate item of Sch 'A' as "supply only")

Supply only water proofing compound (ISI Mark)

M&L, applying two coat of cement base paint including preparation of newly plastered surface of wall complete all as specified and as directed.

M & L two coat of oil bound distemper over a coat of Birla wall care putty on plastered surfaces on wall incl. preparation of surfaces etc.

Complete removal of existing treatment on wall (any number of layers ) by scarping with steel scapers or any other mean including filling depessions of scapped surface with putty and pereparation of surface for further treatment and M&L for two coats of distemper oil emlusion white or tinted on walls complete all as specified and dircted by Engr-in -Charge

Preparation of old decorated surface of ceiling and including cornices plastered or unplastered surfaces by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down , smoke soot moulds , moss and efflorescent salts treating oil and greasy spots and applying two coat of white wash complete all as specified and directed.by Engr-in-Charge

M&L for applying two coat of cement based paint on walls including preparation of old plastered or un plastered surface comlete all as speified and directed.

M&L complete removal of existiong treatment (internal and external) on walls by scrapping with steel wire brushing, scraping down smoke soot/ plants roof from wall/chhajjas comlete all as specified and directed.

M&L , preparation of wall surface and aplying two caot of wall care putty on wall surface finished even and smooth including rubbing complete all as spefied and directed

Excavation in trenches not exc 1.5 mtr depth for foundation etc n.exe 10sqm on plan in and getting out in hard dense soil. complete all as spefied and directed

Returning filling in including spreading, levelling, watering and well ramming in layer nexc 25 cm in soil complete all as spefied and directed

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m complete all as spefied and directed

Demolition of brickwork or stone/ boulders masonry built in cement mortar or cement lime mortar incl all quoins, arches, pillars etc. but not excluding ashlar facing dressed stone work and precast concrete articles.

M&L for rubble random rubble uncoursed, well bounded, bedded and solidly hearted built in cement mortar 1:6 complete all as specified and directed.

M&L Brick work with sub class B bricks straight or curved on plan exc. 6m mean radius built in cement mortar (1:6).

M&L for brick work with sub class "B" bricks straight or curved on plan to any radius in half brick thick wall built in cement morart 1:4 complete all as specified and as directed.

Taking up or down steel tubing and connetion including cleaning for refixing or removing to store of 20mm bore of pipe.

Taking up or down steel tubing and connetion including cleaning for refixing or removing to store of 25mm bore of pipe.

supply and laying 20 mm dia .of bore CPVC pipe SDR11 and Plain CPVC SDR11 fittings (ISI ) marked ,concealed or fixed to wall ,ceiling or laid in floors complete all as specified and as directed by engineer in charge .

supply and laying 25 mm dia .of bore CPVC pipe SDR11 and Plain CPVC SDR11 fittings (ISI ) marked ,concealed or fixed to wall ,ceiling or laid in floors complete all as specified and as directed by engineer in charge .

S&F in repairs 110mm dia PVC(SWR) type B pipes single socketed, in any length with rubber ring joints,fixed to walls/ floor complete all as specified and directed

S&F 75 in repairs mm dia PVC(SWR) type B pipes single socketed, in any length with rubber ring joints,fixed in Wall/laid in floor complete all as specified and directed

S&F 110mm dia PVC(SWR)pipes bends any radious with acces door complete.

S&F 75 mm dia PVC(SWR)pipes bends any radious.with acces door complete.

S&F 110mm dia PVC(SWR)pipes junction,single (single T/Y ) equal or unequal any radious.with acces door complete.

S&F 110mm dia PVC(SWR) vent cowl

M & L 75 mm dia of out let PVC (SWR) floor trap plain with cp grating incl. jointing with solvent cement as in repair

M & L PVC (SWR) gully trap 125 /100 plain with grating incl. jointing with solvent cement as in repair

S&F 15mm angle cock chromium plated,cast copper alloy, with capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe fixed in repair.

S&F 15mm ,bib tap Fancy type long body chromium plated,cast copper alloy, with capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe fixed in repair…

Supply only 15mm,pillar taps fancy type long body chromium plated,cast copper alloy, with capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe.make : Neptune series of prayag or equivalent.

S&F of vitreous china wash basin, white, flat back, size 550 x 400mm Including waste coupling ,waste pipe and labour for fixing pillar tap ,pvc connection but including cutting for and pinning in ends of and including brackets complete all as specified and directed. Note : Pillar tap and PVC connection will be measured paid as supply only.

Supply only 15mm dia PVC connection with PTMT nuts of length 450 mm.

S&F for in repairs vitreous china urinals, Half stall type ,white with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete all as specified and directed.

S&F for as in repair viterous china wash down water closet pan (pedestal pattern) white excluding fixing bolts,flushing cistern and flush pipe including connection to drain and to flushing pipe syphonage pipe etc and mild steel chromium plated or aluminised hinges device & on CP Jet complete all as specified and directed. .

S & F PVC Low level flushing cistren 10 Ltr capacety including all itting such as flush pipe brackets complete all as specified and directed.

S&F Soap dish of CP fixed with pvc rawal plugs and screw complete.

S &F Tublar towel rail 20mm dia D type 60 cm long between flange Brass CP complete.Prayag Cat-BA-40 or equivalent.

S & F in repair Curtain rail stainless steel decorative type 25 mm dia including fixing bracket and end knobs complete specified and diected by engineer in charge.

Dismantling water tanks of any description and in any position , of capacity exceeding 250 litres but not exceeding 500 litres complete all as specified and directed.

S&F Rotational moulded poly-ethylene Three layered antibactrial film tanks (cylinderical vertical ) 500 litres capacity, white colour hoisted and fixed in position complete all as specified and directed.

S & F 20mm ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20 m m - 210 gms / 25mm-455gms/ 40mm - 690 gms)

S & F in repair gun metal globe / gate value with iron wheel head screwed both ends for iron pipe of 20mm bore all as specified.

Surface excavation n.exc. 30 cm deep and av. 15 cm deep and getting out in any type of soil complete

M&L for Chequered cement concrete tiles 30 cmx30cmx25 mm thick, set jointed and pointed in neat cement slurry with grey cement and pigment, in floors, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and directed.

Dismantling of AC (corrugated / semi-corrugated) sheets in roof covering including any type of ridges complete all as specified and as directed.

S&F Pre painted galvalum sheet 0.50 mm thick having aluminum zinc coating 150 gsm/ sqm steel sheet any colour having tensile strength of 550 Mpa as in Roof covering /cladding to wall fixed with self tapping screws complete all as directed by Engineer -in -charge.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces over 10 cm width or girth including preparation of new surfaces.

M&L for 75mm thick PCC (1:2:4) Type C2 using 40mm graded stone agg as in plinth protection surface even and fair without using extra cement including forming & filling expension joints 65 mm deep x 10 mm wide filled with sealing compound grade A complete all as specified and as diected

Excavation in trenches n'exc 1.5 mtr depth and n'exc 1.5 mtr wide in soft/loose soil and getting out complete all as specified and directed.

M&L for brickwork with sub class 'B' bricks straight or curved on plan exc 6m mean radius build in cement mortar 1:3 complete all as specified and directed

M & L Hardcore of gauge n exc 63 mm, deposited, spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface with broken stone or boulders complete all as specified and directed.

M&L for PCC (1:2:4) type B2, (using 20 mm graded stone aggregate), as in foundations / mass concrete complete all as specified. .

S & F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc. complete , drilled for fixing of steel sheeting or other covering Doors, etc. to be prepared for hanging or sliding with and including either gooks ang hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F Framed work such as grills,gratings, etc.. with ends of bars shouldered nd/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for mild steel TMT bars ,10mm dia and over, cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

S & F flue pipes 200 mm dia of mild steel sheet, black, in suitable lengths as approved by the E.I.C fixed to walls complete all as specified and directed.

S & F 250 mm dia MS cowls (with 3 stays), riveted to and including 15 cm length of flue pipes complete all as specified and directed.

M&L for preparation of the newly plastered surfaces of wall & applying 3 coats of white wash on wall surfaces complete all as specified and directed.

Removing excavated soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

M & L for providing PCC (1:2:4) Type B1 using 20 mm graded stone aggregate in foundation, filling and mass concrete, leveling course complete all as spd and directed.

Forming 12mm thick expansion joints filled with pre-formed bituminous filler and to 30mm primed and sealed with sealing compound, grade 'A'

Rolling and consolidation to required level, gradient or camber of formation surfaces in cutting with 8 to 12 tonnes ower roller including watering as necessary complete all as specified and directed.

Excavation in post hole each nexc 0.5 cum getting out returning filling with earth around in layers nexc 25cm with soil complete.

M&L for brickwork with sub class 'B' bricks straight or curved on plan exc 6m mean radius build in cement mortar 1:4 complete all as specified and directed

M&L for providing two coats of water proof coating of Pidifine 2K of Dr. Fixid or euivelent in other make in sunken complete all as specified and directed.

Removing surplus soil obtained from excavation to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting paint complete all as specified and directed.

S & F 15mm dia stop valve CP fancy type screwed to unioun or GI pipe etc complete all as specified and as directed.

M&L non skid ceramic Coloured tiles, 300mmx300mmx7mm thick, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match with the colour of tiles, over and including 15mm thick screed bed or bedding layer of cement mortar 1:6 complete all as specified and directed.

M&L for 75mm thick cement concrete type C2 1:3:6 using 40mm graded stone aggregate as in plinth protection/Path/paving ect surface even and smooth complete all as specified and as directed.

M & L for Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators,sockets,light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M&L, surface point wiring with PVC insulated and unsheathed electric cable 1100 volts grade single core FRLSH confirming to IS 694:2010 having multi stranded copper conductor of 1.5 Sqmm nominal cross sectional area (ISI marked with valid CML No) drawn in and including surface non metallic rigid PVC conduit medium grade( ISI marked with valid CML No) not less than 20 mm dia confirming to IS 14930 (Part-I) 2001, with all fitting and fixing accessories and 1.5 Sqmm FRLSH PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor, connected to common earth dolly by providing suitable lugs with & including pressed steel sunken terminal boxes factory made for mounting switch, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white) ISI marked, fixed with brass screws and cup washers duly painted with two coats of anti corrosive paint/black bituminous paint outside and two coats of aluminium paint inside for mounting switches. sockets etc complete for the following:

For one light point controlled by one switch

For one fan point controlled by one switch

For one 5 pin socket out let 5 amps on same bd complete.

For one 5 pin socket out let 5 amps on indep bd complete.

For one Bell/buzzer point controlled by one way 5 Amps bell push

Description all as per item No 118 here in before but point wiring with 2.5 sqmm FRLSH confirming to IS 694:2010, multistrand copper conductor cable for one six pin socket outlet 15 Amps controlled by one switch on independent board and 2.5 sqmm FRLSH PVC insulated multi strand copper conductor cable as continous earth wire.

S&F ceiling rose surface bakelite 63.5 mm dia three terminal complete all as specified and directed.

S&F switch piano, flush button single pole one way 5 Amp complete all as specified and directed.

S&F socket out let, multipurpose, 2 in 1 5 pin, 5 Amp complete all as specified and directed.

S&F Switch socket combination out let, multipurpose, 2 in 1 5 pin, Amp complete all as specified and directed.

S&F Switch socket combination out let, multipurpose, 2 in 1, 6 Pin 5/15 amps complete all as specified and directed.

S&F bell push flush type, 5 Amps complete all as specified and directed.

S&F of buzzer Ding Dong, AC, 230 Volts, single pole complete all as specified and directed.

S&F electronic step rotary type fan regulator of two module capacity 80 to 100 Watt, 240 volts, AC 50Hz complete all as specified and directed.

S&F Lamp holder including LED Bulb 9/10 watt, with metal ring, PVC/Polycarbonate type with back plate suitable for batten fittings non ISI Marked complete including LED Bulb 9/10 watt.

S&F Decorative ultra slim LED Tubelight fitting of LED with extruded polycarbonate, enviormental friendly energy efficient ready to use, 20 watt, 6500K fitting, incluing reqd length of not less than 1.0 Sqmm PVC multistranded BIS marked 03/02 core copper conductor for electrical connection from ceiling rose to connector of LED fitting including testing on completion all as specified and directed.

S&F recessed/surface LED ceiling light with broad collar frame offering superb energy saving of 36 Watts suitable for 600 x 600 mm ceiling.

S & F security light fittings better optics for uniform distribution IP 65 protection LED of 30 watt, Heat resistance glass, pressure die cast aluminium housing including 25mm dia galvanised iron pipe light grade bracket bent to shape over all length 0.60mtr fixed to wall with 02 Nos FI clamps made of 40 x 5 mm FI, 15 cm long, 8 mm dia bolts and nuts with washers grouted in wall complete including reqd length of 1.5 Sqmm PVC multistranded BIS marked, 03 core copper conductor for connection from ceiling rose to light fittings incl testing on completion all as specified and directed.

M & L for Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store including painting with two coat of synthetic enamel paint over one caot of primr and refixing the same all as specified and directed

Taking down submain wiring of any size any type and in any position metalic/non metallic PVC conduit of wooden batten complete all as specified and directed.

M&L, sub main wiring with two single core PVC insulated unsheathed FRLSH confirming to IS 694:2010, multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 6 sqmm size drawn in and including non metallic rigid PVC concealed conduit medium grade (ISI marked with valid CML No) not less than 25 mm dia confirming to IS 14930 (Part-I) 2001, with all fitting & fixing accessories including one run single core PVC insulated unsheathed 6 Sqmm FRLSH copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed. Make of wire : Finolex, Plaza, Polycab & Make of conduit : Anchor, Modi, Presfit. (NOTE: (i) Two run of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit and the quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface with putty to match with the existing surface.

S&F MCB DB, sheet metal enclosures double door TPN 4 way with bus bar 415 volts 2 in 1 shutter type (METAL DOOR) type with blanking plates where required and IP 43 degree protection complete all as specified and directed.

S&F MCB DB, sheet metal enclosures double door SPN 8 way with bus bar 240 volts 2 in 1 shutter type (METAL DOOR) type with blanking plates where required and IP 43 degree protection complete all as specified and directed.

S & F MCB TPN 40 to 63 Amp 415 Volts complete.,including connection with suitable size copper lugs complete all as specified and directed.

S&F, MCB SPN 40 Amps, 240 volts 'C' series 16 KA ,including connection with suitable size copper lugs complete all as specified and directed.

S&F, MCB SP 240 volts, 63 Amps, 'C' series 10 KA including connection with suitable size copper lugs. complete all as specified and directed.

S&F, MCB SP 240 volts, 6 to 32 Amps, 'C' series 10 KA including connection with suitable size copper lugs. complete all as specified and directed.

S&F sheet metal enclosure, single pole and neutral with a two pin and earth plug and socket with and including one single pole MCB 20. Amps, 240 volts,10 KA complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) vertically, with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Schedule Part-I connecting to earthing test. Testing on completion with and including necessary excavation and earth work in any type soil, earth lead connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded BT stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, internal surface of concrete shall be given 10mm thick plaster in CM 1:4, pre cast RCC (1:2:4) type B-1 (using 20mm graded BT stone aggregate) 40mm thick cover, reinforced with 8mm dia deformed or TMT bars 3 Nos both way with 12 mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh and 15mm dia GI medium grade earth lead protection pipe including provn of earth test point made of 50 x 5 mm MS Flat in 'D' shape 500 mm legth grouted in wall complete 01 x 6 mm multistrand PVC insulated copper conductor ( Green Colour) to be provided from test point to DB through 20 mm dia concealed non metallic conduit complete all as specified and directed.

Supplying, laying, testing and commissioning of XLPE insulated screened PVC bedded galvanised steel strip or wire armured electric power cable (Heavy duty ) with aluminium conductor 1100 volts grade, cross sectional area size 25 Sqmm 4 Core.

Sand filling in trenches with clean dry unwashed sand free from sharp particles, gently punning around the cables complete.

Bricks, old size sub class `B' laid in trenches with width wise along the alignment of the cable as protection complete.

S&F tube 'Light' grade galvanised with all fitting laid in trenches, fixed to wall and floor of 50 mm dia for cable protection complete all as specified and directed.

BHAGIRATH CONSTRUCTION COMPANY

M/s J.B. Construction

M/s Himgiri construction