GRAND LIBRARY AND SCIENCE CENTRE

Amount

Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Earth work OPEN EXCAVATION in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Providing and laying the Granular Sub-base with close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory soil compactor to achieve the desired density, complete as per clause 401 (for grading-III Material) (GSB)

Supplying and filling in foundation, basement with CONVEYED GRAVEL not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation and basement with Filling Crushed Stone Sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation and basement with Filling Crushed Stone Sand and Gravel mix (1:1) in layers of not more than 15 cm thick well watered, rammed and consolidated etc., complete complying with standard specification and as directed by the departmental officers.

CEMENT CONCRETE 1:5:10 [One Cement, Five Crushed Stone Sand and Ten hard broken stone jelly] using 40 mm gauge hard broken granite stone jelly for FOUNDATION including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification.

CEMENT CONCRETE 1:4:8 [One Cement, Four Crushed Stone Sand and Eight hard broken stone jelly] using 40 mm gauge hard broken granite stone jelly for FOUNDATION including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification.

BRICK WORK in Cement Mortar 1:5 [One Cement and Five crushed stone Sand] using best quality chamber burnt Fly Ash Bricks of size 23 x 11 x 7cm for the following including curing etc., complete complying with standard specifications. [Masonry projections wherever necessary for obtaining required elevation shall be done without extra cost].

For Foundation & Basement

For Superstructure in Ground Floor

BRICK WORK in Cement Mortar 1:6 [One Cement and Six crushed stone Sand] using best quality Fly Ash Bricks of size 23 x 11 x 7cm for the following including curing etc., complete complying with standard specifications. [Masonry projections wherever necessary for obtaining required elevation shall be done without extra cost].

For Foundation & Basement

For Superstructure in Ground Floor

For Superstructure in First Floor

For Superstructure in Second Floor

For Superstructure in Third Floor

For Superstructure in Fourth Floor

For Superstructure in Fifth Floor

For Superstructure in Sixth Floor

For Superstructure in Seventh Floor

For Superstructure in Eigth Floor

DAMP PROOF COURSE with Cement Mortar 1:4 [One Cement and CS Sand] 12mm thick with Bonding agent Cebexl 12, Zydex -Zycrete 2X or other equalent compound conforming to BIS at 200ml of one cement bag (50kg) for increased workability and air entrainment used finishing mixed with best approved quality water proofing compound conforming to Indian standard specification as specified by the departmental officers at 2% by weight of cement used and finishing, curing etc., complete complying with standard specification.

Supplying and erecting shuttering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as COLUMN FOOTINGS, COLUMN PEDESTALS, PLINTH BEAMS, GRADE BEAMS, STAIRCASE STEPS, etc., which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. [Payment for centering shall be given after the concrete is laid].

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height For plane surfaces as detailed below , in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid).

RCC FLOOR SLAB, ROOF SLAB, RECTANGULAR BEAMS, ELL BEAMS, LINTELS, LANDING WAIST SLAB, CONAPY SLABS BED BLOCKS etc.,

FOR RECTANGULAR OR SQUARE RCC COLUMNS TOP AND BOTTOM SLABS OF RCC BOXING TO WINDOWS RCC SUNSHADES etc.,

FOR PLANE SURFACES SUCH AS VERTICAL SLAB, SIDE SLABS OF BOXING, VERTICAL DROPS, FACIA, VERTICAL WALL, ETC.

FOR CIRCULAR COLUMNS ETC.,

Providing Additional Strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part there of but not less than 30 cm, over the initial 3.00 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers.

Providing and laying in position, standardised concrete Mix M-20 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/ms and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retad setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu'm') 7670 kg. of cs sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).

For Foundation & Basement

For Superstructure in Ground Floor

Providing and laying in position, Standardised Concrete Mix M-35 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 425 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

For Foundation & Basement

For Superstructure in Ground Floor

For Superstructure in First Floor

For Superstructure in Second Floor

For Superstructure in Third Floor

For Superstructure in Fourth Floor

For Superstructure in Fifth Floor

For Superstructure in Sixth Floor

For Superstructure in Seventh Floor

For Superstructure in Eigth Floor

Supplying, fabricating and placing in position MILD STEEL / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. [Contractor has to make his own arrangements for the supply of steel and binding wire]

Design and execution of post tensioning works, including decoiling the strands, cutting to the required lengths supplying laying of HT strands sheathing (GI corrigated ducts 0.mm thick) jointing with couplers, and inserting the strands, profiling, fixing live end anchorage, including the supply of stressing anchorages, suitable for 5-5 and 5-4 tendon, grout vents, making dead and anchorages including flowering the strends, fixing tendon support bars, supervising the fixing of antibursting reforcement, streesing the cables, end trimming, grouting the cable with cement slurry mixed with admixures with required tools, plants and machineries, and concumables etc., ( shuttering concreting & reinforcement steel, shall be paid under respective items) at all heights including all leads, lifts coordination, with the post- tensioning agency, preparation of drawings obtaining apporoval for the Engineers etc., Rate include providing water, power, cement and admixture of grouting packing of sheathing and anchorages blockings filling of recess pockets after streessing using grouts (Cement slurry mixed with approved admixtures) including providing acces to post tensioning at all heights including all leads, lifts etc., all complete and as approved and as directed by the enginner but exculding the shuttering concreting the reinforcement steel which shall be payable under respective items separately.

Supplying and fixing of void filling geofoam of required size. The material have the nominal density of 30 kg/m3. The rate is inclusive of loading, unloading and conveyance charges, etc complete. The material should got approved by Executive Engineer during execution.

Supplying and fixing of Mild steel structure with toughened glass canopy using 8mm tk clear toughened glass which is supported by MS box section of size 145mmx82mmx6mm tk alround and also at 4’ internals for required length. The M.S box section is fastened to the existing masonry or concrete structure on one side using chemical fasteners and nuts & bolts, etc., The other end of M.S frame is Supported by using 60mm dia M.S pipe tie rod at 3.05m intervals using 60mm dia M.S pipe tie rod at 3.05m intervals which is fastened to MS baseplate of tk 15mm and size of 300mmx300mm. The baseplate is fastened to concrete/ masonry structure using chemical fasterners, nuts & bolts etc., The toughened glass is fixed to the M.S frame using 3M tape, 995 weather sealent and other materials, etc., The rate is inclusive of one coat of primer over red oxide, etc., complete as directed by the departmental officier.

CEMENT CONCRETE 1:5:10 [One cement, Five CS sand and Ten hard broken stone] using 40 mm gauge hard broken jelly for FLOORING including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification. [The rate is inclusive of necessary planking for panelling wherever necessary and complete complying with standard specification and as directed by the departmental officers.

BRICK PARTITION walls of 11.00 cm thickness using best quality Fly Ash Bricks of size 23 x 11 x 7cm in Cement Mortar 1:3 [One Cement and CS Sand] using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers.

For Superstructure in Ground Floor

For Superstructure in First Floor

For Superstructure in Second Floor

For Superstructure in Third Floor

For Superstructure in Fourth Floor

For Superstructure in Fifth Floor

For Superstructure in Sixth Floor

For Superstructure in Seventh Floor

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 16 mm - 18mm of approved quality set in Cement Mortar 1:3 (One Cement and Three CS Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Paving the Top of roof with Solar reflective ceramic tiles of size 305 x 305 x 7mm thick of approved quality and colour laid in Cement mortar 1:3 (One cement and three cs sand) 12mm thick and pointed with tile grout (Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works).

Manufacturing supplying and fixing of STEEL DOOR [SINGLE LEAF] with the specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x6mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts

2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter to conceal the gap between the two shutters at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and fixing in position of ornamental well seasoned teak wood door Double leaves shutter of over all size 1350x2025 mm to fit door frame of over all size 1500 x 2100 mm and the shutter specifications are as follows. Teak wood vertical scantling shall be of size 125x50 mm in Four numbers, horizontal scantling shall be of size 125x50 mm in three numbers ,2/3 bottom panel shall be ornamentally carved planks of size 1100x425 mm in two numbers 550x425 of 6mm thick glass in Two numbers with special type of furniture fittings as required for fixing the shutter in position etc., 2 no of Magnetic Door bush.The rate is inclusive of cost of all materials and labour charges for wrought and put up,fixing door in position,charges for Ornamental carving works, conveyance charges and all other incidental charges as directed by the departmental officers etc.,complete complying with standard specification.

Supplying and fixing Glass door as per requirements with glass door as per requirements with the following specification: The partition and door is made of saint gobain/ Asahi make glass 12 mm tk clear toughened glass with floor spring BT-SI (Dorma) make, single connector cum double connector patch lock fitting (Dorma) make and door is endorsed with handle of 45 mm dia and 20 mm dia thickness and the partition is attached to the existing masonry or concrete structures with 995 weather sealent and other accessories etc., and all are completed as per directed.

Supply and erection of Double Leaves Fire Rated Door with Frame having the dimension of 1800mm x 1400mm with following specification: a. Door Frame 1.6mm: Galvanized 120 GSM branded make JSW b. Door Leaf 1mm: Galvanized 120 GSM branded make JSW c. Shutter Thickness: 46mm d. Honeycomb: In-fill e. Glue Macroplast UR-7221 f. Door Hinges: 4" x 3" x 3mm, Double Ball: Make Assa Abloy Yale Ball bearing Butt Hinges Grade SS 304 - Finish SS g. Door Closer with Standard Arm Finish: Silver h. Lock Set: Dead Lock with both side key i. Door Orientation: To be confirmed by client j. Mounting of door: Brick wall mounted k. Powder Coating: Powder coated in standard RAL paint colour of PO Red (60 to 90) Microns l. Single Point Panic Bar (2 Horizontal): Make Assa Abloy Yale or Equivalent m. Dead Lock with both side key: Make Assa Abloy Yale or Equivalent n. Vision Panel 200 x 300mm 2 Hrs. Fire Glass Schott Pyran with Frame o. Rated Glass Schott Pyran with Frame p. Anchor Bolt with Endcaps The above assembly mounted on concrete or brick wall including the cost of cutting, chipping, concrete packing, pastering, scaffolding all other conveyence as per standard methods and as directed by the Departmental Officers.

Providing and fixing 35 mm thick flush door shutters & Sliding arrangements Double leaves of Solid Core Block Board bonded with phenol farmaldehyde synthetic resin thermopressed and finished with laminate on both side of approved colour and shade with 12 mm thick teak wood external lipping all round. The construction procedure of the shutter should be as per IS 2202. The shutter shall be shop prepared for taking cilindrical lock or latches suitable lock block of wood may be provided for fixing the hardware. The size of block, shall perfectly correspond to the maximum size of lock. The shutter shall be free from twist or warp in its plane and of required size etc. Complete as directed. The Shutters shoul be fixed to the Sliding Arrangements with Top rail in Aluminium with PVC Rollers with locking arrangements suitable for sliding type the rate

Supply & fixing of WPC (Wood Polymer Composite) Frame extruded with size 75mm x 50mm. The single core door made of rigid WPC compound with minimum Bulk Density of 900 KG/ Cub.Mt. & shore hardness of 55. Supply & fixing of WPC door shutter, extruded as a single core board with rigid WPC compound with the thickness of 25mm (+/- 1mm) & minimum Bulk Density of 550 KG/ Cub.Mt. & shore hardness of 55. For the aesthetic appearance, the door shall be a printed digitally on one side of the shutter and the design is as decided by the Engineer in-Charge of the department. The WPC door shall be fixed onto the WPC frame with 3 Nos of 5” SS Hinges and the door shall have 2 towerbolt on one side and 1 towerbolt or aldrop on other side for locking system and 2 numbers of handle on the either side of the door shutter, all made of aluminium.

Supply & fixing of WPC door shutter, extruded as a single core board with rigid WPC compound with the thickness of 25mm (+/- 1mm) & minimum Bulk Density of 550 KG/ Cub.Mt. & shore hardness of 55. The door shall be a plain matt board as decided by the Engineer in-Charge of the department. The WPC door shall be fixed onto the Aluminium “G” type channel with Wheel and the door shall have 2 Hooks in SS, 2 Handles 4” in SS.(Sliding door)

Supply and Installation of Fire Duct Door with Frame having the dimension of 600mm x 1800mm with following specification: a. Door Frame 1.6mm: Galvanized 120 GSM branded make JSW b. Door Leaf 1mm: Galvanized 120 GSM branded make JSW c. Shutter Thickness: 46mm d. Door Hinges: 4" x 3" x 3mm, Double Ball. Ball bearing Butt Hinges Grade SS 304 - Finish SS Make: (EURO) CE MARK e. SS Flush handles for Shaft / Duct Door. Finish: Silver Make: Dorma f. Lock Set: Dead Lock with Single side key g. Door Orientation: To be confirmed by client h. Mounting of door: Brick wall mounted i. Powder Coating: Powder coated in standard RAL paint colour of PO Red (60 to 90) Microns j. Vision Panel of size 200 x 300mm, 6mm thk Toughened Glass k. Anchor Bolt with End caps of Size 8mm * 80 mm. Make: Hilti / Fischer The above assembly mounted on concrete or brick wall including the cost of cutting, chipping, concrete packing, plastering, scaffolding all other conveyance as per standard methods and as directed by the Departmental Officers.

Newly Constructed Roof/Podium with 2K PU Waterproof coating above 2000 Sq.m Providing and Applying two component Polyurethane based cold applied seamless waterproofing coating to the RCC surface like Roof & Podium area applied @ 2.1kg/m2 in single coat using 3mm notched trowel to achieve 1.5mm DFT, including a prime coat of solvent free, medium viscous, epoxy primer @0.2L/m2 and protection with 120gsm Geo-textile over the 7 days cured waterproofing membrane. The Waterproofing material shall have Solids > 98%, Tensile strength >6 Mpa, Elongation at break >600% as per ASTM D 412, crack bridging ability (no cracks up to 3.2mm) confirms to ASTM C 1305, Puncture resistance >300N as per ASTM E154, Shore A Hardness >70 as per ASTM D 2240, Adhesion to peel after water immersion as per ASTM C 794 at 5.2N. Resistance to root penetration. The finished cost to include surface preparation, making coving of 50 mm X 50mm at all right angles of wall Junction with Polymer Repair Mortar and lay 60gsm Geo-textile over the angle fillet when the first coat in still wet, treatment of cracks and laying 120GSM Geo-textile as seperation/protective layer over the fully cured PU coating completely as per specification.

Newly Constructed Roof/Bathrooom. Toilet/balcony/ utility with Cementatius Waterproof coating below 300 Sq.m. Providing and Applying CFTRI approved two component flexible polymer modified acrylic cementitious waterproofing coating with a mix ratio of (5 Liquid: 7 Powder), to the RCC surface like Roof, bathroom, toilet, balcony & utility area applied @ 2.2kg/m2 in 2 coats to achieve .1.2mm DFT, having Elongation at break >120% as per ASTM D 412, Tensile strength >1N/mm2 as per ASTM D 412, Adhesion strength: 0.80 N/mm2 as per ASTM D 4541, crack bridging upto 2mm as per ASTM C 836, Water penetration (5 bar pressure) as per BS EN 12390. The finished cost to inclued surface preparation, making coving of 50mm x 50mm at all right angles of wall Junction with Polymer Repair Mortar and lay 45 gsm glass fibre mesh over the angle fillet when the first coat in still wet, treatment of cracks completely as per specification.

UPVC Window: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work.

Supplying and erecting pull and push type rolling shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc., complete complying with standard specifications and as directed by the departmental officers.(Manual Operated)

Supplying and fixing M.S. Grill for openings corridor side ladder, Entrance Gate and Name Board angles etc., using M.S. flats for inner and outer members which should be fixed as directed by the departmental officers including cost of providing one coat of red oxide primer. The design of MS Grill should be got approved from the departmental officers before use on work.

Providing & fixing MODULAR STAINLESS STEEL RAILING of AISI 304 grade consisting top handrail of 60x2mm thk connected wuth a SS plate as vertical balustrade anchor with SS Rossette plate spaced equally as per detailed drawing with all bends, stud joints & installation at site and fixing 12 mm thick toughened glass panel as per approved drawing etc., complete complying with standard specification and as directed by the departmental officers.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing.The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete complying with standard specification and as directed by the departmental officers.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for Staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100x100x6mm MS base plate encased in the base concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and Fixing in Position urinal Partition with White Marble slab( Adanga) 18mm to20mm thick of 4'0''x2'00'' size and above of best quality including dismantling Masonry,if necessary and redoing the same to original condition etc., complete complying with standard specificationd (The Marable slab should be got approved by the Executive Engineer before use on works).

Providing double nosing for Granite slab etc., complete as per standard specification and as directed by the departmental officers.

Supply and fixing of PVC Wall Corner beading etc., complete complying with standard specification and as directed by the departmental officers.

PLASTERING with Cement Mortar 1:5 (One cement and Five p.sand), 12mm thick mixed with Bonding agent Cebex112, Zydex -Zycrete 2X or other Equalent compound conforming to BIS at 200ml of One cement bag (50kg) for increased workability and air entrainment used finishing in all floors including curing etc., complete complying with standard specification and as directed by the departmental officers.

SPECIAL CEILING PLASTERING and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three P.Sand) 10mm thick mixed with Bonding agent Cebex112, Zydex -Zycrete 2X or other Equalent compound conforming to BIS at 200ml of One cement bag (50kg) for increased workability and air entrainment used finishing including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers.

PLASTERING the surface of walls with Cement Mortar 1:3 (One cement and Three P- sand), 12mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement and with Bonding agent Cebex112, Zydex -Zycrete 2X or other Equalent compound conforming to BIS at 200ml of One cement bag (50kg) for increased workability and air entrainment used finishing in all floors including curing etc., complete complying with standard specification and as directed by the departmental officers.

PLASTERING the surface of walls with Cement Mortar 1:3 (One cement and Three P- sand), 20mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement and with Bonding agent Cebex112, Zydex -Zycrete 2X or other Equalent compound conforming to BIS at 200ml of One cement bag (50kg) for increased workability and air entrainment used finishing in all floors including curing etc., complete complying with standard specification and as directed by the departmental officers.

Brick jelly lime concrete using broken brick jelly of size 40mm uniform gauge in pure slaked lime 1:2:5 (one cement two sand and five brick jelly) by volume and laid over the toilet depression portions in a single layer of required slope etc., complete as per standard specification and as directed by the deparmental officers.

Painting NEW IRON works such as steel doors, windows, ventilators, window bars, balustrades etc., with TWO COATS of best approved first quality and colour of synthetic enamel paint over one coat of red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. [The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.]

Painting two coats of newly plastered wall surface with ready mixed Plastic Emulsion Paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting two coats of newly plastered wall surface with Weatherproof Exterior Emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Supplying and painting the walls with two coats of wall putty as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications (The wall putty shall be got approved by the Executive Engineer before use of work).

Providing ANTI-TERMITE treatment to soil adjacent under building foundation, plinth periphery of the building by applcation of chemicals of ISI 6313-1981 part I to IV in stages to suit the progress of work as per the detailed specification (Measurements taken for the plinthe area for the purpose of payment) including breaking of termite mounds, making holes with clow bar, closing the holes after the treatment and incliding cost of chemicals, labour charges, transport and storing etc., complete complying with the standard specification and as directed by the departmental officers.

Stage.I. spraying anti- termite treatement chemicals solution for foundation concrete surface laying the foundation concrete bottom and sides of the foundation. Stage.II. Spraying anti-termite chemical solution to the grade beam level, spraying for the grade beams, brick, masonry in superstructure in contact with the back fill earth. Stage.III. Spraying anti-termite treatment, chemicals solution on sand for the flooring before laying the flooring zone, Treatment has tobe carried out by making crow bar holes at an interval of 12" to a depth of 8" on the sand filling in basement and after levelling operation is over. Stage.IV. Spraying anti-termite treatment chemicals solution around the building (out side) by making crow bar holes at an interval of 12" to a depth of 8" in the periphery of building and chemical poured inside the holes and closed after the treatement.

Carting out and disposing of the excess contaminated earth from the proposed site to the assigned destination of dumping yard with an average lead of 15km incloding loading,unloading & levelling etc,complete complying with the standard specification and as directed by the departmental officers.

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Jet Black and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three cs sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Supplying & laying Leather Finish Granite slab of size not less than 5' x 2'6" of 18-20mm thick with tolorance of + or - 2mm in flooring, treads of steps and landing laid on bed of 20mm thick cement mortar 1:3 (one Cement and three M-sand) laid and finished with flush pointing in white or colour cement including rubbing and polishing and use chemical for fixing the granite slab with epoxy spacer filling in joint ( like Pedilite,Leticat or equalant) with lather finish or river wash as per architect suggestion. The rate is inclusive of all cutting, laying, conveyane, all other Tools and Plants involved in the work charges and all other incidental charges etc.,complete complying with standard specfication and as directed by the departmental officer. (The granite slab quality, colour, shade and size should be approved by the Executive Engineer before use on works)

Supplying and laying machine cut and mirror polished approved coloured ITALIAN MARBLE SLAB of 18-20mm thick with tolorance of + or - 2mm of approved quality. The Italian marble inlays for flooring is in required pattern laid on a bed of 20 mm thick base of cement morter 1:3 ( one cement and three M-sand) including neat cement float, filling joints with neat coloured cement slurry, curing, polishing and cleaning, high gloss tin oxide polish with Italian Polish Machine as per architect suggestion, The rate is inclusive of all cutting, laying, conveyane, all other Tools and Plants involved in the work charges and all other incidental charges etc.,complete complying with standard specfication and as directed by the departmental officer. (The italian marble slab quality, colour, shade and size should be approved by the Executive Engineer before use on works)

Supplying & laying in flooring & flooring bands Vitrified tiles 1200mmx600mmx10mm of approved shade over a bed of 20mm thick cement mortar 1:3 ( one cement and three M-sand) laid to patterns with Laterite or equivalent make Epoxy stain free ( SP-100) or Ardex Endura grout that is necessary cutting, mitring, curing, cleaning as per architect suggestion and as per detailed drawings, pattern and specification. The tiles to be laid with 3mm PVC spacer and joints to be filled with Laterite non-stain epoxy grout to approved shade as per detail, laying, conveyane, all other Tools and Plants involved in the work charges and all other incidental charges etc.,complete complying with standard specfication and as directed by the departmental officer. ( The Vitrified tiles quality,brand, colour, shade should be approved by the Executive Engineer before use on works).

Supplying & laying in flooring & flooring bands Vitrified tiles 600mmx600mmx8mm of approved shade over a bed of 20mm thick cement mortar 1:3 ( one cement and three M-sand) laid to patterns with Laterite or equivalent make Epoxy stain free ( SP-100) or Ardex Endura grout that is necessary cutting, mitring, curing, cleaning as per architect suggestion and as per detailed drawings, pattern and specification. The tiles to be laid with 3mm PVC spacer and joints to be filled with Laterite non-stain epoxy grout to approved shade as per detail. The rate is inclusive of laying, conveyane, all other Tools and Plants involved in the work charges and all other incidental charges etc.,complete complying with standard specfication and as directed by the departmental officer. ( The Vitrified tiles quality,brand, colour, shade should be approved by the Executive Engineer before use on works).

Dadooing walls with granite tiles of synthetic grey, paradise, and similar varieties of suitable sizes set in Cement Mortar 1:2 (One Cement and Two crushed stone sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Flooring with Self Designed Colour ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing walls with printed design colour glazed tiles of size 300mm x 600mm x 10 mm best approved quality, white / colour glazed tiles set in Cement Mortar 1:2 (One Cement and Two crushed stone sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Tactile Flooring: Supplying and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:3 (one cement and three M-sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete complying with standard specification and as directed by the departmental officers. The rate is inclusive of laying, conveyane, all other Tools and Plants involved in the work charges and all other incidental charges etc.,complete complying with standard specfication and as directed by the departmental officer. (The tactile tiles quality,brand, colour, shade should be got approved by the Executive Engineer before use on work).

Supplying and laying wooden flooring at site 8mm thick of approved make using click laminated floor with in built 3mm sound block class of use 31 water resistant AC 3 grade impact resistant IC3 (as per EN 130 900 / 1400) having 0.60mm MLC (Multi-Layer Guard + SRSG 2) (Scratch Resistant Surface Second Generation) on top of moisture high density fibre board substrate specially developed copy of plank size 1288 x 196 x 8mm having joints tongue and groove secure long lasting joint. The tongue and groove having the edges duly pre impregnated with par affineincluding laying 0.20mm thick alkali resistant polyethylene sheet of density 850kg /m3 beneath the laminated wooden panel to absorb the sound caused including labour charges, loading, unloading, transportation, etc complete complying with standard specfication and as directed by the departmental officer. (The tactile tiles quality,brand, colour, shade should be got approved by the Executive Engineer before use on work).

Wooden Skirting: Providing & fixing 12mm thick x 150 mm high first quality Solid Teakwood Skirting wherever necessary including Melamine polish shade to be match with the same matching shade of wooden flooring & with veneer shade to all wood surfaces with 6mm groove between skirting & gyp/veneer to T.W. framework or T.W. panelling as per architect's detail drawing & design etc complete.

FALSE FLOORING : Providing and fixing of Prelaminated Calcium Sulphate with 60 minute fire rating false floor panels in size 600 x 600mm - 34 thick at an elevation of 600mm FFH,using understructure comprising of required mm cross beams and GI Pedestals securely fixed to the ground using dash fastners. The pedestals should have 2 check nuts to ensure the height adjustments upto 25mm. The panels should be finished with a High pressure anti static laminate having a 6mm be ading on all 4 sides for edge protection. Weight bearing capacity shouls be 3.6 KN CPL and UDL of 15KN Ht.-600mm Installation should comply to earthquake protection Thickness of tile will be based on strucatural caculations supplied by manufacturer and vetted by consultants to suit weight bearing capacity indicated above. Item includes Providing and fixing of Understructure in size 600 x 600mm at an elevation of 600mm FFH, using understructure comprising of 600mm cross beams and GI Pedestals securely fixed to the ground using dash fastners. The pedestals should have 2 check nuts to ensure the height adjustments upto +- 25mm. Weight bearing capacity should be 3.6 KN CPL and UDL of 15KN Ht. 600mm.

Carpet Tile Flooring: Providing and fixing carpet of Approved sample as per given in drawingson existing base with the help of adhesive including one time cleaning and shampoo washing at final stage or as per client requirment. The rate is inclusive of laying, conveyane, all other Tools and Plants involved in the work charges and all other incidental charges etc.,complete complying with standard specfication and as directed by the departmental officer. ( The materials quality,brand, colour, shade should be approved by the Executive Engineer before use on works).-

Providing GRANOLITHIC FLOOR finish of 25mm thickness with Plain Cement Concrete 1:2:4 [One Cement, Two Crushed Stone Sand and Four Aggregate] using 10 to 12 mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc., complete complying with standard specification and as directed by the departmental officers. [The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers].

Providing and fixing in true horizontal level MINERAL FIBRE BOARD FALSE CEILING of silhouette grid system of 600 x 600 mm panel size with 15mm white flanges incorporating a 6mm central reveal in approved colour of approved equivalent make using hot dipped galvanized steel section, exposed surface chemically cleaned capping pre-finished in baked polyester paint wall angle of size 3000mmx19mmx19mm used in the periphery of the ceiling fixed to the wall partition / RC Column / band walls with the help of screws at 600mm C/C. Main runner spaced at a 1200mm C/C suspended by using 2mm dia G.I. wire hanger securely fixed to the structural soffit of RC slab by using 6mm anchor fastener at every 1200mm(max) and 1200mm long cross tee to be interlocked between in Main runner at 600mm.

GYPSUM FALSE CEILING: Providing and fixing in position Gypsum board false celing with 12.5 mm thick Gypsum boards, screwed/fixed to the under structure of suspended G.I. Grid constructed and suspended from the main ceiling consisting of ceiling sections of size 25 x 50 mm maximum center to center distance of 600 milimetre perimeter channel and intermediate channels at maxmum center to centter distance 1200 milimetre galvanized grid should be fixed to reinforced cement concrete slab. The gypsum board should be fixed to galvanized iron grid with necessary screws. The boards should be taped and filled from underside to give smooth, seamless ceiling. The rate should include necessary additional ceiling sections and intermediate channels. Additional intermediate channels should be fixed to strap hangers for additional support to prevent strapping at every 1200 milimeter item to be completed in all respect including necesary sleeves for ducts finishing of joints cut outs and including labour, mateial, lifts, etc. complete complying with standard specification and as directed by the departmental officers.

Providing and fixing Aluminium Luxalon 100mm X 100mm Aluminium Open ceiling of approved colour consisting of Main Runner, Cross Runners of sleek U-Shaped Profiles 15mm wide x 38mm deep x 0.5mm thick with Continuous Paint Line, Double baked and Roll formed from enamelled Corrosion Resistance Aluminium Alloy (Al.Mg) for higher strength and good Roll Forming characteristics. The Cells are connected to form 100mmX 100mm Open cell at a module of 600mm laid on the T-15 grids. The Main tees and cross tees are fixed at a module to form 600X 600 mm and shall be suspended by means of G.I. Suspension Rod 4mm diameter and a Galvanized Suspension Spring Clip at a distance of 1.2mtr c/c. The Linear Aluminium ceiling system should meet the required standards for Green Pro certification and should qualify as green product as per CII green products and services council. The manufacturer should be ISO 9001:2015 Quality Management System Certification compliant with in house testing facility and should have their own manufacturing plant in India.

Suspension System: The Carrier shall be suspended by means of G.I. suspension rod 4mm diameter, and a Galvanised suspension spring clip at a distance of 1.2mtrs centre to centre. Paint Finish: Aluminium cell ceiling Main Runners Cross Runners Upper Section, Lower Section of U-Shaped Profiles shall be chromatised for maximum bond between metal and paint, enamelled twice under high temperature one side with full primer and Finish Coat, the other side (inner side) with a Primer Coating and Skin Coat on a Continuous Paint Line. Mode of Measurements: Measurements shall be wall to wall, measuring the Surface / plan area without any deductions for lights, diffusers, columns or any other openings etc.

Providing and fixing of Green Pro Certified Ceiling in 84R Plain Panel of approved colour consisting of panel 84 mm wide x 16mm deep x 0.5 mm thick with round edges panel length up to 6mtrs coil coated on a continuous paint line double baked and roll formed from enameled corrosion Resistance Aluminum Alloy AA3105 (Al.Mn) for higher strength and good Roll forming characteristics. Panels shall be clipped at a baked enamelled Aluminium carrier of 33mm wide and 65mm deep x 0.95 mm thick in a standard length of 5mtrs made of double baked enameled Aluminium Alloy AA3105 (Al.Mg.) to hold the panel. The carrier shall be fixed to a recommended diameter threaded rod for rigid fixing details. All properties and specifications shall comply with ECCA directives and more specifically EN 1396:1996, The coated coil is passed thru ARKU SIX Hi configuration roller levelling process to ensure the flatness of the coil.The 84R will be Manufactured in CAD/CAM equipment having several stages of Roll forming process. The Panel shall be interior Polyester coated on a continuous coil coating line. The system manufacturer should meet the required standards for Green Pro certification and should qualify as green product as per CII green products and services council.

Paint finish: Aluminium panels shall be chromatised for maximum bond between metal and paint, enamelled twice under high temperature, one side with full primer and finish coat, the other side (Inner side) with a primer coating and skin coat on a Continuous Paint Line. Suspension System: The Carrier shall be suspended by means of G.I. suspension rod 6mm diameter, and a Galvanised suspension spring clip at a distance of 1.2mtrs centre to centre. Mode of Measurements: Measurements shall be wall to wall, measuring the Surface / plan area without any deductions for lights, diffusers, columns or any other openings etc.

BAFFFLE CEILING: Providing and fixing 50x100 baffle ceiling ( 50mm Width & 100mm Height) system comprising of U shape panels. Baffle panels shall be made out of 0.7-0.9 mm thick electro galvanized steel material in lengths of up to 4000mm. The Coil should be stove enamelled on a continuous application for pre-treatment. The coils to go through 4 stages of pre-treatment, three times oven baked through conversion coating, priming and finish coat ensuring superior adhesion, high corrosion resistance and good colour stability. The coils to be painted on both sides after degreasing. Inside surface to have a primer of 5 microns and a coat of natural colour of 5 microns, exposed surface to have a primer of 5 microns, binder of 5 microns and topcoat of approved colour of 15 microns. Baffle Ceiling panels shall be mounted on slotted galvanized grid profile of minimum 2mm thickness in a module of 150mm. Baffle grid shall be suspended and supported by means of 6mm dia threaded suspenders at a distance of 150mm from the edge and 1200mm c/c. Baffle fixing brackets shall be used to keep the ceiling in correct place for the leveling purpose. Baffle panels shall be coil coated in a desired specification. Baffle ceiling system shall be installed in compliances with manufacturer’s technical installation brochure and manual.

Supplying and fixing Linear roll formed 180mm Beveled Slat Ceiling, manufactured out of 0.6mm thick coil coated on a corrosion resistece 3000 Aluminium Alloy series of approved colour. Panel size 180mm wide X 15 mm deep plain diagonal patten, Coil Coated on a Continuous Paint Line, and shall be stove enamelled in a continuous coil coating process with the approved colour on the exposed side and the reverse side with polyester primer. The coated coil is passed thru a multistage high precision customised roll forming line to achieve the desired profile.. Panel shall be clipped to a baked enamelled customised Aluminium panel carrier manufactured in PLC controlled roll forming machine. The Carrier is of 60mm width x 30mm height and 0.90mm thick in standard length of 5 mtr in Aluminium alloy 3000 series (Al. Mg) black with cut outs to hold the panels in a module of 50/100/150/200 mm. 20mm gap between the panels is left open for better acoustics . The Carrier shall be suspended by means of G.I. suspension rod 6mm diameter, and a Galvanised suspension spring clip at a distance of 1.2mtrs centre to centre.

Supply & Fixing of Green Pro certified, 600X600mm GI Tile with easy demountable Clip-In U profile channel system manufactured out of 0.5mm thick Coil Coated on a continuous coil coating process. The Tile to be manufactured on advanced CAD/CAM equipment that includes several levelling stages in the manufacturing process achieved through ARKU SIX Hi configuration roller levelling process to ensure the flatness. Tile ends will be raised with pips and stops to ensure positive engagement into the spring to enable de-mounting of individual panels. The Tile sides will be sufficiently high to ensure a minimum deflection across the length of Tile. All Tiles will be bevel edged. The Tile shall be clipped into clip in profile of 0.5mm thick G.I. The clip in profile shall be supported from slab by means of rigid suspension of 4mm G.I. Rod, Hold on Clamp with Luxalon Clip. The Linear Aluminium ceiling system should meet the required standards for Green Pro certification and should qualify as green product as per CII green products and services council. The manufacturer should be ISO 9001:2015 Quality Management System Certification compliant with in house testing facility and should have their own manufacturing plant. Necessary cutouts for light fixtures fittings has to be provided at ceilings. Suspension System: The Clip-In U Rail system shall be suspended by means of G.I. suspension rod 6 mm diameter, and a Galvanised suspension spring clip at a distance of 1.2mtrs centre to centre. Mode of Measurements: Measurements shall be wall to wall, measuring the Surface / plan area without any deductions for lights, diffusers, columns or any other openings etc.

Saint Gobain Ecophon Solo Ceiling: Providing & Fixing Ecopon Solo Circle with 800mm dia, easily demountable manufactured from High density glass wool utilizing the 3RD Technology with Akutex FT surface on both the sides 85% Light reflectance (of which more than 99% is diffuse reflection). The panel should have 2.53 sabine value at 1000mm o.d.s. Ambient RH and temperature does not exceed 75% and 30 degree C. Thermal resistance (Lamda value-0,035-0,04W/mk). Certified by the Indoor climate Labelling,emission class M1 for building materials and recommended by the swedish Asthma and Allergy Association. Fully recyclable. The glass wool core of the element is to be tested and classified as non combustible according to pr EN ISO 1182 with reaction to fire classification class A2 s1 d0 according to EN 13501-1- European Standard.

Multi panel Combination Rythem ceiling Multi Slat Ceiling - Aluminium Linear Panel Ceiling with 20mm open groove: Providing and fixing Linear Multi combination Slat Ceiling 30mm/80mm/130mm/180mm, manufactured out of 0.5mm/0.5mm/0.5mm/0.6mm thick coil coated on a corossion resistence 3000 Aluminium Alloy series of approved colour. Panel size 30mm/80mm/130mm/180mm wide X 15 mm deep with Perforation of 2 mm diameter diagonal patten, 5 mm centre to centre apertures, 16 % openness, panel length up to 6 mtr, Coil Coated on a Continuous Paint Line, and shall be stove enamelled in a continuous coil coating process with the approved colour on the exposed side and the reverse side with polyester primer. The coated coil is passed thru a multistage high precision customised roll forming line to achieve the desired profile. Double baked and roll formed from enamelled corrosion resistance Aluminium alloy 3000 series (Al. Mg) for higher strength and good roll forming characteristics.

Supplying and fixing ACOUSTICAL WALL PANELLING with square edges made of fibre glass substrate 25mm thick and wrapped on the front side with an acoustically transparent and fire-resistant fabric with an option of colours as per the choice of the Architect/ Person incharge of size 2100x600 or 1200x600 or 600x600 mm providing a minimum sound absorption level of 0.90 NRC to be affixed to wall and construction adhesives as per the instructions shall be fixed to the wall surface using self tapping screws. Silica based construction adhesive shall be dabbed on to the projecting elements (spikes) of the impalers. The rate is inclusive of laying, conveyane, all other Tools and Plants involved in the work charges and all other incidental charges etc.,complete complying with standard specfication and as directed by the departmental officer. ( The materials quality,brand, colour, shade should be approved by the Executive Engineer before use on works).

Providing Wall Panelling using one side teak wood sheet with melamine polishing with following specification. The frame using aluminium tubular section of size 50mm x 25mm x 2mm thick fixing horizontally and vertically in position with wall at interval of 0.60m in both directions, fixing water proof plywood of 12mm thick over the aluminium frame work with necessary screws. One side teak wood sheet of 3.5mm thick will be fixed over the plywood using fevicol and finishing with melamine polishing and the rate inclusive of conveyance to site and labour charges and as directed by the Departmental Officers. The design pattern, water proof plywood, OST sheet and other materials to be used shall be got approved by the Executive Engineer concerned before use on work etc., complete.

Supplying and fixing Lacquered glass Panelling like saint gobain Lacquered glass as per approved shade. Glass to be non toughened 6mm thk. glass mounted on backing ply of appropriate thickness.Glass to be fixed with neutral silicon adhesive of adequate bond strength, to laminated strips affixed to the backing ply. Glass to be finished with edge treatments as per full height glazed partition. The rate is inclusive of laying, conveyane, all other Tools and Plants involved in the work charges and all other incidental charges etc.,complete complying with standard specfication and as directed by the departmental officer. (The materials quality,brand, colour, shade should be approved by the Executive Engineer before use on works).

CURTAIN BLINDS: Supplying & Installing Sunscreen perforated Roller blind optima series - Basket 125 Tex with fabric specification of - ( Fabric compositition polyster 22 % and PVC 78 % , Openenss Factor - 5%, Thickness - 0.68MM +/- 5%, weight per m2 -480.00gsm, yarns count in wrap/weft/cm 19/18 +/-5%, Fire Resistance-FR(USA)KFI(Korea), Tear Resistance-wrap11.9 daN+/-5%,WEFT 150 daN+/-5%,colour fastness-6-7/8 ( white colour base),artificial light xenon lamp , UV resistance Min 3(White colour base),width 2.5M & 3 M The Roller mechanism shall be a moulded unit made from engineering grade plastic polymer with PVC spring support. The Fabric shall be attached to the roller tube with high quality self adhesive tape with manual operation . The fabric shall be attached to the tube with adhesive strip. It should have minimmum one ton fabric which must be placed on the roller before the working section of fabric start.Operational action shall be smooth including necessary hardware for fixing at all places & as directed by Engineer-in-charge etc complete- The rate is inclusive of laying, conveyane, all other Tools and Plants involved in the work charges and all other incidental charges etc.,complete complying with standard specfication and as directed by the departmental officer.( The materials quality,brand, colour, shade should be approved by the Executive Engineer before use on works).

Supplying and Fixing of WPC BOARD PARTITIONS CNC cut WPC panels with wooden frames finished in Mettalic Duco paint to be fixed to the floor and ceiling . ,complete as per the detailed drawing. The rate is inclusive of laying, conveyane, all other Tools and Plants involved in the work charges and all other incidental charges etc.,complete complying with standard specfication and as directed by the departmental officer.( The materials quality,brand, colour, shade should be approved by the Executive Engineer before use on works).

Supplying & fabricating MDF JALI WORK PANELLING like DUCO FINISHED Jali work Partition made of 25 mm MDF finished in Mettalic like Duco paint to be fixed to the floor and ceiling . ,complete as per the detailed drawing . Cost also to include Design and Lazer Cutting on the MDF , and MS supports above False ceiling up to true ceiling. The rate is inclusive of laying, conveyane, all other Tools and Plants involved in the work charges and all other incidental charges etc.,complete complying with standard specfication and as directed by the departmental officer.( The materials quality,brand, colour, shade should be approved by the Executive Engineer before use on works).

Supplying & fixing WALLPAPER of Approved Shade / Finish/ textured Wall Paper on wall / partition As per detailed Drawing/ Elevation. Rate includes sanding, scrubbing, making the receiving surface smooth of imperfections so as to receive the wall paper.etc complete.The rate is inclusive of laying, conveyane, all other Tools and Plants involved in the work charges and all other incidental charges etc.,complete complying with standard specfication and as directed by the departmental officer.( The materials quality,brand, colour, shade should be approved by the Executive Engineer before use on works).

Supplying and fixing in position of Name Board of following sizes with Tamil letters sticker on vinyl board including cost of PVC sheet and fixing Tamil letters sticker on th PVC sheet ad directed by the departmental officers with necessary screws, transportation etc., complete complying with standard specfication and as directed by the departmental officer.

Name board size 12" x 4"

Name board size 18" x 4"

Name board size 24" x 4"

Supplying fabrication & erection of Name board made of ACP board with Steel frame suitably supported by MS angles providing emblem and Acrylic Letters including cost of Letters, all materials, erection charges and finishing etc excluding cost of GST and as directed by departmental officers.

Supplying and fixing Direction Board for Section in ACP board with golden finishing of letters as directed by the Departmental officers. The rate includes cost of all materials, making charges, loading, unloading and conveyance charges, cost of stickers and all other incidental charges etc but excluding GST complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing Name board of size 1.20m x 0.60m in ACP board with golden finishing of letters as directed by the Departmental officers. The rate includes cost of all materials, making charges, loading, unloading and conveyance charges, cost of stickers and all other incidental charges etc but excluding GST complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing Brass Letters with finishing of letters as directed by the Departmental officers. The rate includes cost of all materials, making charges, loading, unloading and conveyance charges, cost of stickers and all other incidental charges etc but excluding GST complete complying with standard specification and as directed by the departmental officers.

English Letters 15''

Tamil Letters 25cm

Providing two legged scaffolding using 15cm diameter blue-gum posts or casuarina posts or best quality bamboo posts of 3.5m over all length (3m+0.25m projection+0..25m into the ground) the distance between the two rows being 1.25m and the spacing of posts being 2m in both the rows with two horizontal posts with 0.5m overlap on either side and braces at2m c/c including longitudinal and transverse middle braces to step up and providing a platform with country wood planks of 40mm thick and 1m width etc.,in a complete form using coir and nails 1m run.

for 26.50m height

for 46.50m height

Providing, assembling and Supplying of Double Glazed Performance glass, heat Strengthened clear Glass (IGUs) of size and shape as required and specified of approved, comprising of an outer heat strengthened clear glass of following thick of approved colour and shade with reflective soft coating on surface #2 and an inner heat strengthened clear glass of following thick , spacer tube 12mm wide , dessicants, including primary seal and secondary seal ( structural silicon sealant ) etc. all complete for the required performance , as directed by the engineer -in - charge. The heat strengthened clear glass having properties as visible Light transmittance (VLT) of 25 to 35 %, Solar heat gain coefficient less than or equal to 0.27 and U value of 3.0 to 3.3 W/m2 or lower degree K etc. The IGUs shall be assembled in the factory/ workshop of the glass processor. For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (8mm + 12mm + 8mm)

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of Structural Glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers

(c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass....... (d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. (e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified.

The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in- charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge. Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this sub- head. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. up to two decimal places.

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings, the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-inCharge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Aluminium Fin (Bull Nose Cap of size 150 mm) : Designing, providing & fixing the Aluminium SDF finish of approved colour & finish (as per the drawing) metal Fin as per size & type given below with approved profile thickness not less than 2mm thick. Thickness of coating shall be not less than 40 microns. Aluminium fin to be fixed in to the glazing mullion by using aluminium extruded SDF finished bracket (Thickness of bracket not less than 6.0mm) with SS fasteners, bolts & nuts & sealant and as per drawing. Rate shall include the cost of all materials, accessories etc complete. Rate shall exclude the cost of glazing system which will be measured under the respective item. System to be designed to with stand design wind pressure of 230 Kg/Sqm confirming to IS 875 part 3 and other load parameters

Painting two coats of plastered wall surface with TEXTURE PAINTING of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specifications and as directed by the departmental officers. (The paint shall be got approved by the Executive Engineer before use of work).

Fabricating, supplying and fixing in position GLASS FINS SUPPORTED GLAZING to external faces of the building fixed in straight/slope/curvilinear profile consisting of (Clear toughened float glass 10mm+1.5 mm PVB layer+10mm clear toughened float glass)with CNC pre-drilled holes glazed panels of approved make and size securely bonded with Stainless Steel 304 plates alloy electropolished, of approved make, fixed with articulated flat headed bolts for holding the adjoining glass panels in combination with toughened laminated fins (Clear toughened float glass 10mm+1.5 mm PVB layer+10mm clear toughened float glass) as per design requirement for support. The glass fins shall be properly edge polished with CNC pre-drilled holes and fixed perpendicular to the Facade plane at the junction of joints in glazing rigidly fixed at floor and ceiling using chemical grouting material, with necessary Stainless steel end connector to the shape with all adequate sealant to ensure absolute water tightness, necessary peripheral frame members fixed with suitable angles, brackets, fasteners, etc. as per the manufacturer's detail and approved by the Architects. The dawn glass of AIS may be used for the same.

Supplying and fixing of LOUVERS made of aluminium using 63 mm x 37 mm Aluminium plain section powder coated, 100 mm Louver section, Glazing plate, Aluminum L angle, and other necessary accessories to complete etc., complying with standard specification and as directed by the departmental officers.

Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer.

Supplying and fixing GLASS PARTITION with glass door as per requirements with glass door as per requirements with the following specification: The partition and door is made of saint gobain/ Asahi make glass 12 mm tk clear toughened glass with floor spring BT-SI (Dorma) make, single connector cum double connector patch lock fitting (Dorma) make and door is endorsed with handle of 45 mm dia and 20 mm dia thickness and the partition is attached to the existing masonry or concrete structures with 995 weather sealent and other accessories etc., and all are completed as per directed.

Providing expansion joint 12.5mm width in RCC roof slabs between RCC twin beams using PVC water bar of 150mm wide centre bulb of 4mm to 6mm thickness of approved quality and brand and including filling the inner space with suitable non-absorbent flexible and well compressible filler materials of approved quality and covering the top surface with GI sheet 30cm wide and 1.6mm thick using phill plugs, GI screws, limpet cup washers, bitumen washers, etc., complete complying with standard specifications and as directed

Providing expansion joint of 12.5mm wide in between RCC twin columns from top of pedastal to full height including filling the inner space with suitable non-absorbent, flexible and well compressible filler materials of approved quality and brand; finishing the sides of RCC columns with polysulphide sealents for a depth of 7.5mm on either side covering the inner space filled with filler materials as above etc., complete complying with standard specifications and as directed.

Supplying and fixing of ACP Sheet etc and the rate is inclusive of loading, unloading and conveyance charges, etc, complete complying with standard specification.

Supplying and fixing of safety net arrangements in the construction site for labour safety and the rate is inclusive of loading, unloading and conveyance charges, etc, complete complying with standard specification.

Supplying and laying of TAMIN Paver Block of 80mm thick. Over a base layer of crushed stone sandfilling incl. Cost of materials laying and Labour charges etc., complete complying with standard specifications and as directed.

Providing and laying Wet Mix Macadam for 250mm compacted thickness in two layers each layer 125mm compacted thickness using vibratory compacting rollers with physical requirements of aggregate conforming to table 400-11 and grading requirements of aggregate conforming to table 400-10 of MORTH specification fourth revision and entire work to the carried as per MORTH specification.

Supplying, laying and jointing G.I. Pipes of approved quality and best variety of "B" class pipe of the following dia including labour fixing G.I. Specials, (excluding charges for cutting and threading of pipes, cost of such specials) to wall with necessary teak wood plugs, clamps, screws, thread balls, shellac, etc., making holes on the walls (or) drilling holes in roof and making good the dismantled portions to original condition with necessray brick work / concrete and plastering wherever necessry with necessary scaffolding charges. The pipes are to be painted with the 2 coats of good variety and approved best quality of synthetic enamel paint over a priming coat of red oxide etc., complete in all floors complying with standard specification. G.I. pipes shall be got approved by the Executive Engineer before use on works. EXTERNAL WATER SUPPLY -BELOW GROUND LEVEL.

50 mm dia GI Pipe

40 mm dia GI Pipe

32 mm dia GI Pipe

Supplying, laying and jointing G.I. Pipes of approved quality and best variety of "B" class pipe of the following dia including labour fixing G.I. Specials, (excluding charges for cutting and threading of pipes, cost of such specials) to wall with necessary teak wood plugs, clamps, screws, thread balls, shellac, etc., making holes on the walls (or) drilling holes in roof and making good the dismantled portions to original condition with necessray brick work / concrete and plastering wherever necessry with necessary scaffolding charges. The pipes are to be painted with the 2 coats of good variety and approved best quality of synthetic enamel paint over a priming coat of red oxide etc., complete in all floors complying with standard specification. G.I. pipes shall be got approved by the Executive Engineer before use on works. EXTERNAL WATER SUPPLY - ABOVE GROUND LEVEL.

50 mm dia GI Pipe

40 mm dia GI Pipe

32 mm dia GI Pipe

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, UPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works. Below Ground Level

100 mm Dia

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, UPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works. Above Ground Level

100 mm Dia

Supplying, laying and jointing CPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using CPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works. Below Ground Level

50 mm Dia

40 mm dia

Supplying, laying and jointing CPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using CPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works. Above Ground Level

50 mm dia

25 mm dia

20 mm dia

Supplying and fixing in position the following CPVC Specials of heavy type and approved quality and good variety excluding fixing charges but including necessary cutting and threading of CPVC pipes, jointing the CPVC specials and jointing the specials with pipe line using CPVC adhesives etc., complete complying with standard specification. (The CPVC specials should be got approved by the Executive Engineer concerned before use on works.)

50 mm dia ELBOW

40 mm dia ELBOW

25 mm dia ELBOW

20 mm dia ELBOW

50 mm dia TEE

40 mm dia TEE

25 mm dia TEE

20 mm dia TEE

50 mm dia COUPLER

40 mm dia COUPLER

25 mm dia COUPLER

20 mm dia COUPLER

50 mm dia UNION

40 mm dia UNION

25 mm dia UNION

20 mm dia UNION

Supplying and fixing in position the following GI Specials of heavy type and approved quality and good variety excluding fixing charges but including necessary cutting and threading of GI pipes, jointing the GI specials and jointing the specials with pipe line using GI adhesives etc., complete complying with standard specification. (The GI specials should be got approved by the Executive Engineer concerned before use on works.)

50 mm dia UNION

40 mm dia UNION

32 mm dia UNION

50 mm dia ELBOW

40 mm dia ELBOW

32 mm dia ELBOW

50 mm dia COUPLING

40 mm dia COUPLING

32 mm dia COUPLING

50x40mm dia Reducer

40x32mm dia Reducer

50x40mm dia Reducer Elbow

40x32mm dia Reducer Elbow

Supplying and fixing in position first quality and approved variety of Gun metal GATE VALVE with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications [for both internal and external water supply arrangements]. The valves to be used on work shall be got approved by the Executive Engineer before use on work.

50 mm dia

40 mm dia

32 mm dia

Supplying and fixing in position first quality and approved variety of BRASS BALL VALVE with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications [for both internal and external water supply arrangements]. The valves to be used on work shall be got approved by the Executive Engineer before use on work.

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

Supplying, fixing and testing of approved make CI Wafer type Butterfly valve rated for PN-16 pressure rating including rubber gasket, flanges, nuts, bolts, washers and painting complete as required. The valves to be used on work shall be got approved by the Executive Engineer before use on work.

62 mm dia Butterfly valve

80 mm dia Butterfly valve

100 mm dia Butterfly valve

Supplying fixing,testing and commissioning of approved make of PN 16 range Brass Diaphragm Pressure reducing valve,with pressure gauge and syphonic cock etc.,complete.

32 mm dia pressure reducing valve

40 mm dia pressure reducing valve

62 mm dia pressure reducing valve

80 mm dia pressure reducing valve

Supplying and fixing of approved make 25mm dia Brass Air release valve etc. complete The valves to be used on work shall be got approved by the Executive Engineer before use on work.

Supplying,fixing and testing of PVC floor trap with CP grating, 150mm nominal size square, 100mm diameter of the inner hinged round grating various inlet from 40 dia to 110 dia and various outlet from 75 dia to 110 dia with the extension pipe / boss tee connections, fixed in cement concrete sunken floors / core cutting etc., complete.

Supplying,fixing and testing of PVC floor clean out used in cement concrete sunken floors/ core cutting,75 or110mm dia extension pipe / boss tee arrangements with female thread, fix with upvc / pvc male thread plug with frame gascet, ss screws

Fabricating, Supplying, fixing in position of Hot dipped Galvanized MS brackets made out of Angles, Channels, Flats and hot galvanized insert plates, according to the drawings at specified location at suitable intervals. The bracket shall be fixed both horizontally and vertically depending on the pipe locations such as shaft, ceiling, column faces and beam soffit etc. The rate shall include fixing the brackets/plates by using necessary size and dia of anchor fastners or any type fastening methodology approved by architect. The rate also include making cutouts/pockets in masonry wall to the suitable size in order to fix the bracket in wall and restore the finish after grouting the pocket with cement concrete etc. complete

supplying and fixing of PVC gully trap, etc., complete complying with standard specification.

Supplying and fixing of cockroach trap , made up of SS Chrome finished which contains floor drain strainer to protect the intrusion of cockroaches and insects through the drain etc., complete complying with standard specification.

Construction of INSPECTION CHAMBER following clear sizes 0.60m X 0.60m including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five m sand] using best quality of Fly Ash Bricks of size 23x11x7cm with Plastering with Cement Mortar 1:3 [One Cement and Three P. Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three cs Sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.

Supplying and fixing in position best quality PVC SOIL / WASTE PIPES of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry. RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. [The PVC pipes should be got approved by the Executive Engineer before use on works]. The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level.

160 mm dia

110 mm dia

90 mm dia

75 mm dia

63 mm dia

50 mm dia

40 mm dia

Supplying and fixing in position best approved of BIS quality of 110mm dia PVC RAIN WATER DOWN FALL PIPES having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

160 mm dia (One Floor)

160 mm dia (Seventh Floor)

110 mm dia (Second Floor)

Supplying and fixing in position PVC SPECIALS of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. [The PVC specials should be got approved by the Executive Engineer before use on works].

75 mm dia ELBOW

110 mm dia ELBOW

75 mm dia ELBOW WITH DOOR

110 mm dia ELBOW WITH DOOR

75 mm dia TEE WITH DOUBLE DOOR

110 mm dia TEE WITH DOUBLE DOOR

75 mm dia Bend

110mm dia Bend

75 mm dia Y WITH DOUBLE DOOR

110 mm dia Y WITH DOUBLE DOOR

75mm x 63mm Reducer

110 mm x 75 mm dia reducer

75 mm dia Vent Cowl

110 m dia Vent Cowl

Providing , fixing, testing and commissioning of white vitreous china glazed wall mounted type water closet (European type) of approved make conforming to IS 2556-Part III with seat cover and lid, CP brass hinges and rubber buffers, complete with integral low level PVC flushing cistern complete with supply of necessary fittings, supporting bolts /CI / MS brackets flushing pipe with fittings and clamps, overflow arrangementand angle cock of approved make and finish,together with cp conncetion pipe to the cistern etc cutting and making good the walls and floors wherever required all complete as per specification and direction of the Engineer-in-Charge.The cistern shall be complied water saving dual flush (3 to 6 litre per flush).

Sanitary wares like Physically challenged toilet Set of approved make supply &installation by the contractor, storing, leading, installing, testing and commissioning closet set-2 for Disabled toilet, including Floor mounted European Water closet with cistern complete with fittings and seat cover one hinged SS rail, of SS grab bar-600mm, necessary accessories like pan connector, brass screws and one set of wash basin without faucet, 32mm dia waste coupling, 32mm dia bottle trap etc; .complete. The side gap between EWC mouth and pan connector to be filled with silicon sealant.

Providing & fixing WHITE VITREOUS CHINA FLAT BACK HALF STALL URINAL of 580x 380x 350mm with white PVC automatic flushing cistern Parryware/ Hindware/Seabird/ Orient (Coral) with Sensors and fittings, standard size CP brass flush pipe, spreaders with unions and clamps (all in CP brass) with waste fittings as per IS:2556, C.I trap with outlet grating & other couplings in C.P brass including painting of fittings and cutting and making good the walls and floors wherever required, of type:

Sanitary wares like Rectangular washbasin of approved make and CP fittings of approved make supply &installation by the contractor, storing, leading, installing, testing and commissioning of White color/colors Rectangular Wash basin and the following accessories. Works including fixing following accessories: 32mm dia cp brass waste coupling, 32mm dia cp brass bottle trap with extension pipe including necessary supporting brackets, connection tube etc; complete. The supporting brackets, bolt and nuts supplied by the contractor. Works including cutting and making good the walls /floor wherever required, including conveyance of all materials to the site, all labour charges, all taxes etc; complete.

Supplying ,installing,testing and commissioning of Pillar tap for wash basin including necessary accessories etc, complete

Supplying and fixing SS Double Coat hook fixing with necessary screws etc., complete

Supplying , fixing in position and testing SS health faucet with wall hook one metre long flexible tube, angle cock with wall flange all complete including cutting and making good the walls wherever required.

Supplying and installing SS toilet paper holder fixed with SS screws complete.

Providing and fixing P.T.M.T. BOTTLE TRAP for Wash Basin and Sink (Prayag make or Equivalant)Bottle Trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling,77mm breadth with 25mm minimum water seal, weighing not less than 260gms. etc., complete complying with standard specifications.

Providing fixing soap dish holder of approved make etc., complete complying with standard specifications.

Supply and fixing of liquid hand wash dispenser which is automatic sensor operated, wall mounted, rust proof, SS with GPSP powder coated , enhanced motor power offer more stable quantity of produced liquid etc., complete complying with standard specifications.

Providng and fixing 600mm long SS towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arangement of approved quality colour and make etc., complete complying with standard specifications.

Providng and fixing SS Towel ring complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arangement of approved quality colour and make etc., complete complying with standard specifications.

Supplying,installing,testing and commissioning of Long body bib cock for Janitor including necessary accessories etc.complete. The pillar tap shall be complied flow rate at 2.75 / lpm at design pressure of 80 psi of approved make conforming to IS 2556-Part III with seat cover and lid, CP brass hinges and rubber buffers, complete with integral low level PVC flushing cistern complete with supply of necessary fittings, supporting bolts /CI / MS brackets flushing pipe with fittings and clamps, overflow arrangementand angle cock of approved make and finish,together with cp conncetion pipe to the cistern etc cutting and making good the walls and floors wherever required all complete as per specification and direction of the Engineer-in-Charge.The cistern shall be complied water saving dual flush

Supplying and fixing in position INDIAN MAKE BEVELLED EDGE MIRROR of approved quality and brand ornamental wooden framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Supplying and fixing of SS Sink of size 1200x550x180mm etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.

Supplying, fixing and testing of approved make Centrifugal monoblock transfer pump comprise the following specification for domestic water supply from UG sump to OHT with required flow rates and Head along with Control panel supplied by manufacturers and all the accessories including connection with water suppy network as indicated on the drawing.

5 LPS @ 80M Head (1D + 1S) - Domestic water transfer pump 5.0 HP Monoblock Pump

7 LPS @ 90M Head (1D + 1S) - soft water water transfer pump for HVAC soft water UG sump to Softwater OHT at terrace leve

Supplying, fixing, testing and commisioning of approved make of HYDROPNEUMATIC SYSTEM pump With VFD for domestic water supply(one working-one stand by) with fiber glass pressure tank with required litre capacity and replacable bladder, including necessary valves, air release valve, water inlet valve for priming, pressure guage, base frame, pressure switch, powerindication lamps and DOL starter and electrical cable for hydropneumatic system.etc complete., It has located at terrace.(Vendor to submit performance curves and technical catalog of the proposed model for review & information).Equipments tags to be provided. cost Including all the necessary control valves,Ball type foot valves & NRVs ,pump contraol panels & cables Valve tags

Supplying and erecting 2.00 HP ISI make bore well SUBMERSIBLE MOTOR with requried accessories for the 5 HP ISI make Three PHASE electric motor 2900 RPM, 400 / 440V 50Cys. Submersible Pumpset having brozen impellers, S.S.Shaft cable of discharging 100 to 200 LPM aginst a total Head of 135M to 100M with ISI Mark and with an outlet of 50mm and suitable for 150mm dia borewell , including Conveyance and Errection charges including required G.I. specials, M.R. Tape, Electrical connection charges, delivery pipe connection and other plumbing works including hire charges for Chain pully, Tripod and other Tools and trial run for three days etc., complete complying as directed by the departmental officers.

Supplying and fixing heavy duty FRP manhole frame and cover with the load carring capacity of 25 TONNES of clear opening size 600 x 600 mm including necessar fitting as per manufacturer requirement etc.

Supplying and fixing SFRC Manhole cover with size 600 x 600 mm including necessary fitting as per manufacturer requirement etc.

Supply fabrication and fixing of MS puddle flange on the concrete wall

Manufacturing, supplying and fixing in position plain cement concrete precast kerb slab of size 600 mm x 600mm x 100mm in Cement Concrete 1:1.5:3 (One cement, one and half m.sand and Three jelly) using 20mm HBG stone jelly including cost of moulding charges, casting of slab, finishing, curing, fixing and pointing the slab with CM 1:3 (One Cement and Three Sand) to full depth of slab etc., complete complying with standard specification and as directed.

DRILLING 150mm dia [6"] Vertical bore using power drill in hard rock to any required depth as directed by the departmental officers including labour charges for inserting casing pipes to the require depth assembly in drilled hole including welding the joint if necessary, grouting the casing pipe etc., and including transportation charges for the rig and support vehicle. Borewell 1 & 2

Borewell upto 150m below GL

From 151m upto 180m

From 181m upto 210m

From 211m upto 240m

From 241m upto 280m

From 281m upto 310m

From 311m upto 340m

Supplying and fixing of PVC CASING PIPE 160mm dia suitable for 6" Borewell conforming to I.S. 12818 - 1992 with screwed and socked and centering guides for every 15m interval etc., as directed by the departmental officers. [with / without slot]

Supply suitable PVC End Cap (6kg/sqcm) of best for casing pipe of 6" dia borewell quality with ISI mark, The PVC should got approved by the departmental officers.

Supplying and fixing 5HP /40 stage delivery submersible motor including panel board ISI make for 6" dia bore well with pump, necessary accessories such as bolt gun metal jet assembly with 1 number pressure gauge metal complete comprising with the following additional accessories and submersible cable. - The motor shall be of ISI approved variety and shall be got approved by Executive Engineer before erection- Accessories:-. a. 3 Phase star delta starter of 32 AMP of approved quality and make with ISI marks - 1 No. b. 3 Phase 32 AMP main switch of approved quality and make with ISI marks - 1 No. c. Single phase preventer of approved quality and make with ISI marks - 1 No. d. Switch Board to accommodate the starter and main switch power capacitor of suitable capacity as per standard norms of TNEB.

Supplying and fixing M.S. fabricated wall mounting PANEL BOARD with internal wiring as per I.E. rules and necessary locking arrangements with suitable DOL type push button, STAR delta starter, suitable in amps DPC switch,0 to 500 V voltmeter, 0-20Amps Ammeter, single phase preventor, Pilot lamp with 3 bulbs to indicate power supply,3no. and including all specials. a) Suitable DOL push button automatic starter-1 no. b) Suitable15amps DPC switch - 1No. c) 0 to 500V Voltmeter - 1No. d) 0-20 Ammeter - 1No. e) Single phase preventor - 1No. f) Pilot lamp with three bulbs to indicate power supply - 1No. etc., complete.

Supplying and Fixing of 1 1/4" dia H.I tensile U.P.V.C pipe of best quality for delivery cum support pipe for submercible motor inside borewell etc., complete complying with standard specifications. 40mm dia UPVC pipe

Supplying and fixing of Nylon rope for submersible motor of approved quality in etc,complete complying with standard specifications.

Supply and run off WATER PROOF 3 CORE 4 sq.mm flat PVC insulated copper cable for submersible pumpset in the borewell including fixing and tying with copper wire and clamping water pipe etc., complete as directed by the departmental officers.

Tensile Structure Item No. 1. Steel Structire : The Structure shall be designed in accordance with I.S. 800 with the design wind speed asdefined by IS: 875 based on ocation and site conditions and load combinations as defined by IS 875. Item No. 2:- Tensile Membrane fabric The Membrane should be minium of Ferrari 900 gsm Tensile Membrane fabric.The abobe fabric will be patterned, welded with the high frequency weldingmachine, end pockets to accommodate kedar profile and will be fixed using special aluminium exrusions to suit the structure. The complete structure will be designed for the wind load, live loads etc.

Supplying and fixing Colour Galvanum sheet roof of 0.47mm thick and steel tubular box section of 100x50x3mm of 1meter interval including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers.

Supplying and laying Chain link fenching of 75 X 75 mm , 10 gauge with steel frame of L angle of 50 X 50 X 6 mm in vertical post @ 1.80 m intervel and horizontal stiffners of 25 X 6 mm plate@ 1.00 m intervel etc., complete.

Providing and fixing 150/200mm wide water stopper at the concrete junctions at all levels with minimum 750 mm overlapping at joints.

LANDSCAPING:

Supplying and planting of healthy well grown tree sapling, special effect/accent plant in 12' bag size, minimum 1.5- 2 mts in height, without damage of braches and roots, excavation of pit size 750mm x 750mm x 750mm and backing filling of topsoil, red earth or equilent fertile soil, compost,bio-pesticides with proper staking and wrapping. Rate includes plant cost, soil mixtures, transport, supervision,ect., complete complying with standard specification and as directed by the departmental officers.

Terminalia mantaly- 2200mm

Areca palm- 1700mm

Plumeria acutifolia-1500mm

Raphis excelsa- 450mm

Supplying and planting of healthy well grown shrubs in 6'' bag size, minimum 0.45mt in height, without damage of shoots and roots, excavation of pit size 450mm x 450mm x 450mm and backing filling of topsoil, red earth or equilent fertile soil, compost,bio-pesticides with proper staking. Rate includes plant cost, soil mixtures ,transport,supervision,maintenance of 12 months...all complete.

Pseuderanthemum reticulatum / Eranthemum 'yellow'

Clerodendron inerme / Forest jamine

Ceasalpinia pulcherrima-600mm

Supplying and planting of healthy well grown groundcovers in 6'' bag size, minimum 0.3 mt in height, without damage of shoots and roots, excavation of pit size 300mm x 300mm x 300mm and backing filling of topsoil, red earth or equilent fertile soil, compost,bio-pesticides with proper staking. Rate includes plant cost, soil mixtures , transport, supervision, maintenance of 12 months all complete.

Lantana swellonia 'purple', 'white'

Allamanda cathartica 'dwarf yellow'

Rhoe discolor

Golden daturanta

Ixora sunkirt 'pink'

Digging out the soil upto 150mm depth, all the debris, stones, weed roots or any other material shall be removed. ,Spreading and leveling of garden soil, red earth or equivalent soil, farm yard manure , and bio-fertilizers mixture to required depth,to formation of mound or undulated lawn and rolling , grading area as shown as drawings.

Supply of well healthy Bermuda G2 lawn must be pure,free from weeds and dibbling the grass, watering, gapfilling, weeding, mowing, maintenance of 12 months.

Supply and fixing of 2 inch dia P.P ball valves with all necessary fittings and with 10"plastic valve box etc. all complete etc.

Supply and fixing Sprinklers with riser and all fittings of Medium range rotary popup -sprinkler with adjustable irrigation radius range of 8-10 M.

Supply and fixing Sprinklers with riser and all fittings of Medium range rotary popup -sprinkler with adjustable irrigation radius range of 10-18 M.

Supply and laying Integral LLDPE Drip lateral tubes with inline emitter 4-6 lph, class 2 of 16 mm dia with necessary fittings and accessories complete etc.

Supply and fixing of Quick coupling kit with all fittings complete etc.

Supply & Fixing of 120mesh filter with 40 cu.m/hr capacity and Monobloc or openwell submersible pumpset of having 4lps to 7 lps discharge and 30 mtr head of design flow along with control panel, voltmeter , cable, non-return valve, air release valve with all accessories.

PLAIN CEMENT CONCRETE 1:2:4 [one cement, two crushed stone Sand and four hard broken stone jelly] using 10-12 mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (pvc) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals.Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside.Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug.

FIRE FIGHTING ARRANGEMENT

Supply and fixing of Fire fighting application oblique type Stainless Steel Hydrant Valve of size 63mm – dia with oblique type instantaneous coupling with rotating wheel to open and close the valve including MS flange of table “E”, bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges, necessary scaffolding and re- doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers. (Make; OMEX / KARTER /LIFE GUARD /SAFE GUARD/ EQUIVALENT.

Supply, Installation of Fire fighting application 180 degree swinging type, hose reel drum with 20 mm dia braided thermoplastic hose of 30 meters long so as to extent to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve & open & close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers.

Supply, and fixing in position of Fire fighting application Hose of 63mm dia of 15mts length binded by copper wire with 63mm dia Stainless Steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the department officers Near every hydrant points including conveyance, all incidental charges, necessary scaffolding and re- doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers.

Supply, and fixing in position of Fire fighting application 63mm dia Stainless Steel short length Branch Pipe with hexagonal type spray nozzle of 15mm (or) 20mm jet bore. Near every hydrant points including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers.(MAKE:OMEX/KARTAR/LIFEGUARD/SAFE GUARD/EQUIVALENT.

Supply and Fire fighting application M.S. Hose Box to keep two numbers of Hoses and one number of branch pipes with nozzle. having proper glass window type double door with universe open key, painted inside white and outside PO red. Near every hydrant point including conveyance, all incidental charges, necessary scaffolding and re- doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers. (Make: OMEX/KARTAR/LIFE GUARD/ SAFE GUARD/ EQUIVALENT.

Supply and fixing nominal bore quartized bulb type sprinkler bulb 68 Deg C fast response pendent type including GI collar for each sprinkler bulb, mounted in MS pipe line using suitable size MS threaded coupling, thread, Shellac etc.,as per standard methods and including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers. (Make: OMEX/KARTAR/SAFE GUARD/EQUIVALENT.

Supply, Installing, testing and commissioning of Stainless Steel Corrugated Flexible Braided Pipe (Hose) for dropping sprinklers below false ceiling. Pipe shall be 16 bar pressure rating and 1500mm long, 25mm dia with union / reducer, collar, clamps, etc. It shall have UL listed and FM approved.

Supplying and installing of approved type Rosette Plates (Recessed Type in Two Pieces) for sprinklers below false ceiling area. The Rosette shall be fabricated by MS plate of 2mm thick and the finish shall be powder coated and colour, as directed by the Departmental Officers.

Supply, erection, testing and commissioning of MS ‘C’ Class Heavy duty pipe as per IS 1239,to withstand a developing pressure of 10kg/sq.cm including necessary fittings like MS flange of table ‘E ‘ Elbows, reducers, gaskets, both, nuts with washers & Joints as per standard method of arc welding .Including one coat metal primer and two P.O RED painting including conveyance ,all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers.

200 mm dia

150 mm dia

100 mm dia

80 mm dia

50 mm dia

25 mm dia

Wrapping and coating anti-corrosive treatment for underground MS pipe having one coat of anti-corrosive metal primer ,one layer of Asphalt Tar tape wound over the M.SPipe as per standard methods as per standard specification as directed by the departmental officers

150 mm dia

Supply, erection, testing and commissioning of following sizes heavy duty foot valve including all accessories such as MS flange of table ‘E’ gaskets, bolts &nuts, etc., installed at end of 150/200 mm dia suction pipeline at sump including conveyance ,all incidental charges ,necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers. Make :NORMEX/KARTAR

200mm dia

100mm dia

Supply ,erection, testing and commissioning of Cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water including necessary MS flange of table ‘E’ gaskets , bolts& nuts including conveyance all incidental charges,necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers.Make:NORMEX/KARTAR.

150mm dia

100mm dia

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Non-return valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead, tank at terrace leve l near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312. including conveyance, all incidental charges, necessary scaffolding and re-doing dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers.

150mm dia

100mm dia

Supply, erection, testing and commissioning of Gun metal Gate valve of size 50mm dia including necessary MS flange of table ‘E’ gaskets, blots & nuts, etc. installed at pump house delivery line for the purpose of priming water to suction line including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers. Make:LEADER/EQUIVALENT.

Supply, erection, testing and commissioning of Gun metal non-return valve of size 50mm dia including necessary MS flange of table ‘E’ gaskets, bolts & nuts, etc., installed at pump house delivery line for the purpose of priming to suction line so that to control one way including conveying, fixing and incidental charges etc complete as per standard specification and as directed by the departmental officers, Make: LEADER/ EQUIVALENT.

Supplying and fixing of PVC ready made WATER TANK of 1000 Litre capacity of best and approved quality with ISI specification and having inlet,outlet, overflow and clearing pipe arrangements and labour charges for fixing in position with all necessary accessories and transporting at site of work etc., complete complying as directed by the departmental officers.

priming tank mounted with the supporting arrangement fabricated using MS angle for the height of 3.00 mtrs from the floor level, inlet, outlet, and drain arrangements inside the fire fighting pump room as directed by the department officers

Supply and laying of following sizes of armoured Aluminium/Copper cables for electrical motor. control Panel, Pressure switch, jockey motor etc. all incidental charges necessary scaffolding and re- doing the dismantled portions to its original condition wherever found necessary etc. Make.POLYCAB/PARACON/FINLOEX/EQUIVALENT

3 cores 185sqmm armoured aluminium cable

3 core 10 sqmm armoured copper cable

10 core 2.5 sqmm armoured copper cable

2 core 2.5 sqmm armoured copper cable

Earthing arrangements with GI earth plate including charcoal and salt with necessary excavation in all soils and to full depth as may be required and masonry work. Refilling the sides of foundation with excavatedearth as per thestandard specification and as directed by the department officers.

Supply, erection, testing and commissioning of pressure Gauge with 0 to 141 kg range of reputed make with necessary value, milling thread Ms coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance. All incidental charges, necessary scaffolding and re- doing the dismantled portions to its original condition wherever found necessary etc. complete as per standard specification and as directed by the departmental officers. Make: H-GURU/ISIMARK/EQUIVALENT.

Supply, erection, testing and commissioning of suitable Pressure switch of reputed make line indfoss or Donfoss including necessary values, couplings etc. connected with electrical main control panel and setup at proper differential so as to auto start& auto stop the electrical motor. Jokey motor including conveyance. all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary metering protections & indications complete as per standard specification and as directed by the departmental officers. Make: DONFOSS/INFOSS/ISIMARK/EQUIVALENT.

Supply, Installation, Testing and commissioning of Diesel engine driven main Fire Pump suitable for automatic operation and consisting of following complete in all respects as required. (a)1 No. Horizontal split Casing centrifugal type fire pump capable of delivering 2280 LPM against a total head of 70 mtrs so as to ensure a minimum pressure of 3.5 Kg per sq cm at the farthest top most hydrant/ Outlet with pump casing of cast iron to grade FG 200, IS 210 -1978 and parts like Impeller, shaft sleeve, bearing ring etc of non corrosive metal either like Bronze, brass or Gun Metal and shaft stainless steel. b) 68 BHP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant BS & IS standard complete. c)Auto starting mechanism, 12 volts 24 volts electric starting equipment like self Motor, Dynamo, Solenoid switches etc. d)110 ltrs capacity Diesel tank mounted over stand fabricated using 25mmx25mmx6mm size MS angle, providing with level indicator, inlet port, outlet port, drain port and diesel return line port and fuel pre filter, after filter etc.

Supply erection testing and commissioning of fire fighting application horizontal centrifugal type pump rated for 2850 LPM at 70 mtrs head with electrical motor of 60 HP of 415V, 3 phase connection, complete with base plate and accessories. (Make : Kriloskar or Equivalent). The rate is inclusive of necessary vibration bed mounting, etc as per standard method as directed by departmental officers.

Supply, erection, testing and commissioning of 180 LPM 70 metres Head Pressurization pump with 10 HP electrical motor of kirloskar make with suitable base frame, Including necessary vibration bad mounting etc., including conveying, fixing and incidental charges etc complete as per standard specification and as directed by the departmental officers.Make: KIRLOSKAR / EQUIVALENT.

Supply, erection, testing and commissioning of fire fighting application monoblock motor pumpset of 900 LPM at 40 metres head to develop 3.5 kg/sq.cm at the heightest and farthest hydrant point to make 30 m water jet at the time of fire fighting emergency cicumstances, coupled with 11 KW / 15 HP rated three phase 414 volts, 50 Hz, 2880 rpm electrical motor the pump with cast ron body, bronze impeller, rope gland packaging, suction size of 80 mm dia. delivery size of 65 mm dia., including the cost of foundaton concrete anti vibration mounting, rain safety hood and etc. complete as directed by the Departmental Officers (Kirloskar make KDS 1555+ or Equivalent)

Supply, erection, testing and commissioning of Fire fighting 4 way fire brigade inlet with necessary Gun metal 63 mm dia non return spring shutter arrangements so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry, including conveyance, all incidental charges, necessary scaffolding and re- doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers.

Supply, erection , testing and commissioning of Air release valve of 20mm dia so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers. Make: KARTAR/ EQUIVALENT.

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS 15683 with pressure gauge, discharge hose & control nozzie, wall mounting bracket, safety clip etc., ncluding conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition whererver found necessary etc complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT/ SAFETY FIRST / EQUIVALENT.

Supply and fixing of Carbon-di-Oxide Gas Type 2 kg. capacity Fire Extinguisher as per New IS15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc., complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Supply and kept in position of 9 litres capacity Fire Buckets of 4 Nos. with Bucket Stand as per standard specifications and as directed by the Departmental Officers

100mm Dia

80mm Dia

50mm Dia

Supply and fixing of Addressable Fire Alarm Control Panel consists of display board which will have 160 Character Display with Touch key pad, Mother board 32 Bit Processor, In-built RS-485 Networking Circuit for peer to peer networking, In-built USB 2.0 Port, Loop Card having 254 devices of both detectors and modules in a single line circuit, SLC supports both Class A and Class B wiring Approval: UL Listed etc. complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of Addressable Active Repeater Panel consists of display board having 160 Character Display with Touch key pad, Mother board which will have 64 Bit Processor, Inbuilt S-485 Networking Circuit for peer to peer networking etc. complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of Addressable Detectors with base with Binary coded address setting. Dual LED’s for 360° visibility etc. complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of Addressable Detectors with base with Binary coded address setting. Dual LED’s for 360° visibility etc. complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of Multi Sensor - Heat Cum Smoke detector etc. complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of Addressable Manual Call Point - Resettable type - with back box with Binary coded address setting with Status LED for 360° visibility complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of Conventional Manual Pull Station - Single Action complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of Conventional type Horn / Strobe wall mounted type rated at 90 dBA @ 1m for Audible annunciation and 15cd minimum flashing at 1 Hz for visual indication complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of Conventional type Horn wall mounted type rated at 100dBA @ 1m for Audible annunciation complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of Fault Isolator Module capable of monitoring shorted loop circuit and automatically restore communications complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of Response Indicators for all detectors located above the false ceiling etc., complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of 24VDC Power Supply with 5 amp rating, having LED indications for Power supply ON,battery Fail,Battery Charging,battery back up etc. complete complying with standard specification and as directed by the departmental officers.

1. Supply and fixing of 10 KLD RBC Packaged STP System containing the following: MS Tank coated with FRP of size 5.35 mL x 1.5mW x 1.65mH 1 No. Sewage Holding Tank 1 set Lamella Plates for Primary Clarifier / Settler 1 No. Aerator for Bio – Zone 1 set Rotors housed in the Aerator 1 set Bearings for supporting the Rotors 1 set Bearing Housing with seals 1 set Lamella Plates for secondary clarifier / settler 1 No. Reduction gearbox 1 set Coupling for the above 1 set Sprocket and chain drive. 1 No. Bar Screen

2. Sewage transfer pumps – 1set 3. Drive Motor for RBC Rotor – 2 4. MGF Feed pumps – 1 set 5. Dosing system – 1No. 6. Multi Grade Filter – 1No. 7. Activated Carbon Filter-1 No. 8. Control Panel for all drives 9. Interconnecting pipe lines and electric cables 10. Collection tank 11. Treated water tank etc. complete complying with standard specification.

1.Supplying, Erection & Commissioning of Domestic water Softening Plant with the following equipment with mentioned specification: a) Filter feed pump : 1 No (1W+1S) b) Multigrade sand filter : 1 No c) Activated carbon filter : 1 No d) Water softner : 1 No e) Interconnecting pipeworks : 1 No f) Water Metre : 2 Nos g) MCC Panel : 1 No 1. For Filter Feed Pumps – Monobloc horizontal type pump (make kirloskar/texmo/KSB/CRI) made of cast iron with impeller of flow rate 20,000 litres/hr with inbuilt motor of capacity 5Hp 415v. The pump also enclosed with 2Nos of suction valve, discharge valve, Non-Return valve, pressure gauge and a rotometer. 2. Multigrade Sand Filter of dia 1200mm and height of 1800mm made of mild steel with epoxy coating internals having shell thickness 4mm and design operating flow rate of 20,000 lr/hr graded sand as filter media and pressure gauge of 1no and also with all necessary accessories,etc, complete complying with standard specification.

Supplying and Fixing of Cubical Partition wall Size of Cubicles : As per measurements Colour of HPL Boards Thickness of Compact Laminate :12mm Door size : 600mm*1785mm Width size:1700mm Overall height :1995 ( Including 150mm Ground Clearance) Accessories : Stainless steel (Grade - 316) & Aluminium a) SS Gravity hinges b) SS Adjustable leg c) SS Coat hook d) SS Door knob e) Aluminium U Channel f) SS Lockset with indicator g) Aluminium anodised toprail h)Aluminium Door stopper Channel i) Screws ( SS Grade - 304) & Wall Plugs j)Noise deafening tapes for grooves in doors & Pilasters.and also with all necessary accessories,etc, complete complying with standard specification.

Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Fabrication, supply and fixing in position of 'N' type ventilators using M.S. angle of size 25 x 25 x5 mm for frame and M.S. Flat of size 20 x 3 mm for fixing the weld mesh and using 25 x 22 x3 mm 'T' section for frame glass. Special type of Hold fast welded to the frame of 45 degree inclined towards centre for wall and fxing the weldmesh 25mm square including cost of 3mm thick pinheaded glass panes for all panels and fixing the glass panels with necessary clips & putties with required bolts, nuts and washers and one coat of red oxide primer etc. including necessary dismantling, making holes in RCC columns, beams, masonry wherever necessary with power drill to the extend required and made good to the original conditions after fising as directed by the departmental officers.

Electrical Item:

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) ( 4 points / Coil) Higher End

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End

Wiring with 3 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point Higher End

Supply and fixing of single box type 4'-20 W LED fitting (Philips / Havells / Eq) complete with conduit pipe suspension from the ceiling with 20 W LED tube with PVC unsheathed Copper leads from terminals to the fitting .

Supply and fixing of Dual colour 15W LED Recessed round type fitting with integral driver with necessary connection complete.

Supply and fixing of 24W LED slim fit down cool white output of 6500°K round recessed mounting type fixture with PVC Unsheathed Copper leads from terminal to the fitting with necessary connection (Higher End)

Supply and fixing of 12W Magneto Linear Collimator 5 Nos. (LD17L- Make:Wipro/equivalent) mounted on single phase track rail with 100W driver and accessaries with necessary connections complete.

Supply and fixing of 60W LED (Klite: Aarsh Series Id:2850//equivalent) with PVC unsheathead copper leads from terminals to the fitting and necessary connection complete.

Supply and fixing of 4 rows of circular suspended linear LED fitting of wattages 144W of dia 2400mm,108W of 1800mm,72W of 1200 mm,72W of 800mm with Aluminium Extrusion body & with PMMA milky diffuser for uniform & glare free lighting. Fixture should be suitable to form any shape as per authority approval. (Klite / equivalent).

Supply and fixing of 4x1 30W LED (Wipro-TZ LM66 Series/equivalent) suitable to make the false ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 33 W 2 x 2 LED Square type recessed fitting with (Wipro Verge - LM29 Series /equivalent) suitable to make the false ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 36 W 2 x 2 LED decorative Square type recessed fitting (Wipro / Elate CRCO10 Series/equivalent) with PVC unsheathed copper leads from terminals to the fitting

Supply and fixing of eGroup light sensor (Wipro /equivalent) for LED fittings with necessary connections and testing in good condition

Supply and fixing of 2 Nos. linear 4ft recess / Suspended 28W LED (Crompton Vogue / Eq) of dimensions (1148mmx67mmx73mm) capable of forming any decorative pattern chosen by the departmental officials concerned to make the false ceiling a piece of art and to be suspended from steel chain / necessary mounting clips with 3Core copper cable of length not less than 1.5 mtr from terminals to the fitting

Supply and fixing of 3 Nos. of linear Y Shaped recess / Suspended 36W LED with each arm of 2ft (Crompton Vogue / Havells Destello / Eq) capable of forming any decorative pattern chosen by the departmental officials concerned to make the false ceiling a piece of art and to be suspended from steel chain / necessary mounting clips with 3Core copper cable of length not less than 1.5 mtr from terminals to the fitting.

Supply and fixing of 40W LED triangular shaped Pendant type Luminarie (Crompton capella /Eq) of dimensions not less than 600 mm x 519 mm x75mm with suspension from the ceiling with necessary mounting kits and with PVC unsheathed Copper leads from terminals to the fitting.The outer powder coating should be customised as per the Colour shades chosen by the department officials concerned.

Supply and fixing of 40W LED circular shaped Pendant type Luminarie of (Crompton Lunar /Eq) with suspension from the ceiling with necessary mounting kits and with PVC unsheathed Copper leads from terminals to the fitting.The outer powder coating should be customised as per the Colour shades chosen by the department officials concerned.

Supply and fixing of 40W LED hexagon shaped Pendant type Luminarie (Crompton Epsilon /Eq)of dimensions not less than 515mm x 595 x 75mm with suspension from the ceiling with necessary mounting kits and with PVC unsheathed Copper leads from terminals to the fitting.The outer powder coating should be customised as per the Colour shades chosen by the department officials concerned.

Supply and fixing of 1 No. 48W high power LED green line smart luminaires having a life span of 40,000 burning hours with 32mm dia GI pipe (Class ‘B’) with 1No. 32mm GI Bend complete on the existing wall with 16A aerial fuse unit on MS plate with PVC unsheathed copper leads with MS clamps & aluminium painting (Higher End)

Supply and fixing of 12W tiltable Spot light (Klite Trisha Round Adjustable ) made of extruded Aluminium housing and high power COB LED as a light source with beam angle not greater than 40 degree and vertical tilt angle not less than 30 degree with PVC unsheathed leads from terminals to the fitting.

Supply and fixing of 12W High efficiency LED Bollard light fitting (K-Lite make Verbena /Eq) suitable with PVC unsheathed copper leads from the terminals to the fittings and painting of suitable color

Supply and fixing of 9w Neon flex profile light of 10 mtrs length with Front and End connector with Floor Mounting junction box (Make K - Lite Id 3230 Neon Flex/ equivalent) with IP 65 Protection with necessary connection complete.

Supply and fixing of 12w LED strip light of 10 mtrs length with Front and End connector with Floor Mounting junction box (Make K - Lite Id 7290 \/ equivalent) with IP 67 Protection with necessary connection complete.

Supply and fixing of 1200mm Sweep BLDC Ceiling fan complete (higher end) with 2 Module 100 W Fat Step Regulator (Higher End) with stepped with 1 metre down rod on the existing fan clamp.

Supply and fixing of 375mm (15") sweep (Heavy duty) AC exhaust fan complete without provision of holes in the wall

Supply and fixing of louvers shutters arrangements for 400 mm (16") sweep (Heavy duty) AC exhaust fan.

Supply and fixing of 150W LED flood light (Higher end) with 40mm dia. GI pipe (class B) with 1 no.40 mm GI bend complete on the existing post/ on wall with 1.5 sq.mm PVC unsheathed copper leads with MS clamps and with painting.

Supply and fixing of 2nos.6A two module 5 pin socket ,2 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. (Higher End)

Supply and fixing of 3nos.6A two module 5 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. (Higher End)

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. (Higher End)

Supply and fixing of 1no./6A two module 5 Pin socket, 1no. 6A one module switch on suitable module surface mounting box (Plastic) with module cover plate (plastic) on wall with connections.Higher End

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections.( Higher End)

Supply and fixing of 20Amps flush type wall socket DP MCB complete set for AC plug in flush with wall with earth connection (For AC Plug)

Supply and fixing of 5W, 230V AC Supply "EXIT" LED Light in rectangular aluminium body material with necessary connection complete.

Supply and fixing of sudo 6W Led Pathway finder (K - Lite Id 2746)with IP 65 Protection with necessary connection complete as per Site Condition. (12W LED Path step light )

Supply erection, testing, commissioning and handing over of Almonard make Single phase 180W AHV-4' silent model aircutrain dimension of 265 (W) x 255 (H) x 1220 (L) with 960rpm motor with very silent operation and 2 mtrs effective air throw with Noise level of 62 DB and necessary connection complete.

Supply, installation, Testing and Commissioning of 6000 mm pole with Single Arm Phoenix Florian pole made of circular mild steel pipe (grade YST 210) 88.9mm Dia x 2.9mm thick with 4623mm Height. The double arm bracket is a split constructed type, Bracket stem made of MS pipe 76.1mm Dia x 2.6mm thick, emerging from a forged ring upto a height 290mm covered at the top with MS sheet of 3mm thick. The angular projecting double arm made of MS Pipe 38.1mm x 2mm thick extending from stem on either that facilitate the fitment of luminaire at 600mm on either side from the vertical axis of the bracket stem. Pole section welded by certified welders using high end MIG welding processes. PDC aluminium service door 348mm height x 80mm width shall be provided with the company logo embossed on the bottom of the door and safety rope.

The control gear tray is prewired with 2.5 Sq.mm cable, 6A SP MCB and 32A Ramanuj stud type 4 way terminal block for loop-in / loop-out arrangement, 5A 2 Way terminal connector and provision for earthing. Any other internal cables and connections shall not be covered in the scope of supply. Mild steel mounting plate 250mm Square x 12mm thick Steel of grade E250 to IS 2062 : 2011 with 4 elongated holes 38 x 19 to suit M16 x 500mm bolts of grade 4.6 at CC 180. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation. All dimension are within +/- 5% tolerance. After fabrication, the pole should be processed using shot blasting equipment to achieve the best smooth finish on its surface. The manufacturer should have an in-house shot blast facility to prevent having to reprocess the blasting work due to delay that could affect the bond between the blasted surface of the pole and protective coating.

The pole is coated with zinc rich primer & pure polyester powder coating or epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint (coating thickness 60-80 microns). The Pole shall be provided with Graphite grey / Anthracite grey / Black.

Supply, Installation, Testing & Commisioning of 50W LED Street Light with 100 lumens per watt Side mounted pole top luminaire. Asymmetrical light distribution. Luminaire made of pressure die cast aluminium alloy of high corrosion resistance and non corrosive stainless steel fasteners. Clear toughened glass. Protection class IP66. Mechanical resistance IK08. Pure polyester powder coated graphite grey /anthracite grey / jet black. Available colour temperature 2700K / 3000K / 4000K / 5700K, Colour rendering index (CRI)>70. SDCM-3 MacAdam. LED module with expected service life of at least 60,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency >85%, Power factor >0.97, THD <10%, Surge protection 6KV.

Inhouse NABL accredited lab and Manufacturer should have Inhouse NABL accredited lab and manufacturing of light fixture.Suitable for mounting on to 60 mm dia pipe at lateral (side entry). Luminaire dimension : 526mm length x 174mm width x 90mm height. CE & BIS Certified.

Supply, installation, Testing and Commissioning of 6000mm Double Arm Phoenix Florian pole made of circular mild steel pipe of two section (grade YST 210) Bottom section 139.7mm Dia x 3.6mm thick with 3000mm Height & Top section 114.3mm Dia x 3.2mm thick with 4684mm Height. The double arm bracket is a split constructed type, Bracket stem made of MS pipe 76.1mm Dia x 2.6mm thick, emerging from a forged ring upto a height of 750mm sealed at top with a decorative gravity diecast aluminium flower bud design (111mm Dia x 202mm Height). The angularly projecting double arm made of MS pipe 60.3mm Dia x 2.6mm thick extending from stem on either sides, spruced up with MS sheet between the stem and arm and facilitates the fitment of street light luminaire at 1100mm on either sides from the vertical axis of the bracket stem. Pole section welded by certified welders using high end MIG welding processes.

PDC aluminium service door 348mm height x 80mm width shall be provided with the company logo embossed on the bottom of the door and safety rope. The control gear tray is prewired with 2.5 Sq.mm cable, 6A SP MCB and 32A Ramanuj stud type 4 way terminal block for loop-in / loop-out arrangement, 5A 2 Way terminal connector and provision for earthing. Any other internal cables and connections shall not be covered in the scope of supply. Mild steel mounting plate 250mm Square x 12mm thick Steel of grade E250 to IS 2062 : 2011 with 4 elongated holes 38 x 19 to suit M16 x 500mm. bolts of grade 4.6 at CC 180. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation. All dimension are within +/- 5% tolerance. After fabrication, the pole should be processed using shot blasting equipment to achieve the best smooth finish on its surface. The manufacturer should have an in-house shot blast facility to prevent having to reprocess the blasting work due to delay that could affect the bond between the blasted surface of the pole and protective coating.

Supply and fixing of 32 A FP MCB in 4 pole sheet steel enclosure in flush with wall and earth connection. (Higher end)

Supply and fixing of 32 A DP MCB in 2 pole sheet steel enclosure in flush with wall and earth connection. (Higher end).

Supply and fixing of 63A FP MCB in sheet enclosure in flush with wall with earth connection. [The MCB and metal enclosure should be with Legrand / Hager make]

Supply and fixing of 100A FP MCB in sheet enclosure in flush with wall with earth connection. [The MCB and metal enclosure should be with Legrand / Hager make]

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 7 segment 4 way TPN MCB sheet steel distribution board (Higher end) with metal /acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 2 pole ELCB / RCD (totally 8 ways in one segment) (3x 4 ways in each segment) and seperate provision for MCB / Isolators ( totally 12 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following on wall with earth connection only i. 32A 4P MCB - 1 no. ii. 32A 2P 30MA RCBO - 3 nos. iii. 6A to 32A SP MCB - 12 nos.

Supply and fixing of 7 segment 8 way 63A TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in each segment) and seperate provision for MCB / Isolators ( totally 18 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only. i. 63A 4P MCB - 1 no. ii. 63A 4P 30MA RCBO - 3 nos. iii. 6A to 32A SP MCB - 24 nos

Supply and run of 2 of 1.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour (For Strip light, Special Circular Pendent, 6A plug, 12W Track Light)

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion( For 2 Nos. 6A & 3 Nos.6A Plug)

Supply and Run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm. PVC insulated SC unsheathed FRLS copper wire and making good of the concealed portion. (For 16A, 20A AC plugs)

Supply and laying of 4 of 6 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre and laying the cable through 40mm dia HDPE Pipe and refilling the earth to make good(For bollard Light)

Supply and clamping of 4 of 6 sq.mm PVC armoured LTUG cable on wall / post through 40mm dia HDPE Pipe with MS clamps (For bollard Light)

Supply and Run of 4 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 6 sq.mm. PVC insulated SC unsheathed FRLS copper wire with painting of suitable colour.

Supply and Run of 4 of 16 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable 40 mm PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 16 sq.mm. PVC insulated SC unsheathed FRLS copper wire with painting of suitable colour.

Supply and Run of 4 of 25 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 25 sq.mm. PVC insulated SC unsheathed FRLS copper wire with painting of suitable colour.

Supply and Laying of 4 x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.(For Street light pole)

Supply and clamping of 4 x 16 sq.mm PVC LTUG armoured LTUG cable on post or on wall through 40mm dia HDPE Pipe with MS Clamps.

Supply and fixing of brass cable gland suitable for 4x16sq.mm PVC LTUG armored copper cable, with earth connection.

CABLE TRAY Supply & installation of galvanized iron pre fabricated perforated type G.I. cable tray (suspension covered separately) Rate shall be inclusive of all accessories like coupling plates, joints, right angle bends, etc., required as standard material. As required supports like Threaded Hot dip Galvanized M.S. rods complete with Anchor fastner, bolds, nuts, washers, MS supports, etc.

150mm x 50 x 1.6mm Cable Tray

300mm x 50 x 1.6mm Cable Tray

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection

Supply and fixing of 15 KVA Three Phase in -Three Phase Out True online SCR Type UPS system with Isolation transformer with 30 Nos of 12V/150 AH SMF batteries to be placed on 2 Nos of battery rack with suitable battery Interlink cables for 2 Hours Back up Time.The batteries should have warranty not less than 2 years (MR)

Supply and fixing of 60 KVA / 360V Three Phase in -Three Phase Out True online SCR Type UPS system with Isolation transformer with 60 Nos of 12V/150 AH SMF batteries to be placed on 2 Nos of battery rack with suitable battery Interlink cables for 2 Hours Back up Time.The batteries should have warranty not less than 2 years.

Supply and fixing of 400 mm (16 inch) wall mount, Oscillating type fan with necessary accessories with connections complete

Supply and fixing of Acrylic LED Name Board for the size of 30' x 3' for English Letters mounting on suitable MS angle iron framework to withstand windspeed of 160KM/hr.

Supply and fixing of Acrylic LED Name Board for the size of 30' x 3' for Tamil letters mounting on suitable MS angle iron framework to withstand windspeed of 160KM/hr.

Supply and fixing of Post top luminaire of K-Lite make KL-4990 Dixon of 20W LED on K-Lite make Chinar lighting pole KP-4222 which is fixed in the base of the Compound Wall.

Supply and fixing of Crompton make 40W MAPLE LED decorative post top (LPT0-40-CDL) made of Pressure die cast aluminium housing with IP65 rating on suitable length 32 mm dia GI pipe (Class 'B') with supply and fixing of MS box of size 30mm x 20mm x 10mm and door with lock & key arrangements in existing pillar gate with supply and fixing of 6A DP MCB inside the MS box with PVC unsheathed Copper leads and necessary connection complete.

Supply and fixing of Water tight Street Light pillar box which is enclosed by Automatic Timer i between the 2nos of 63A FA MCB.And this 2x2 Pillar box mounted on the sutiable concerte fundation.

Supply and Fixing of k-LITE Make 45 W LED MAGUDAM model top Light Luminar on K-lite make DECORATIVE BRACKET on compound wall with necessary bolts and nuts and Supply and fixing of 1No of 6A SP MCB (Legrand/ Hager make), 4way terminal block inside the built in Control box with PVC unsheathed copper leads from the terminals to the fitting.

Supply and Fixing of k-LITE Make Linear Wall Washer on wall

LIGHTING ARRESTOR Supply and Installation of 8mm dia Aluminium alloy Solid Round Conductor of material AlMgSi used in air termination and down conductor system . Cross sectional area of conductor should be 50 mm². Test Parameter: a.Lightning impulse current of 100kA for 10/350 µs b.Electrical resistivity - 0.034 µΩm, c.Tensile strength - 178 MPa or N/mm² d. Salt spray - No Sign of Corrosion. Tested as per IEC 62561-2. CAPE Type: SRC 8–AL/equivalent.

Supply and Installation and Installation of Nylon Conductor Holder for Parapet wall for holding 8 mm dia Aluminium alloy round Conductor. CAPE Type: PCH 8 / equivalent.

Supply & Installation of Nylon roof conductor holder for flat roof with concrete block for fixing 8 mm dia Aluminium alloy Solid Round Conductor in the terrace flat surface at every 1 mtr. CAPE Type: MBPCH8 / equivalent.

Supply and Installation of Stainless steel 304 Grade Cross Connector for 8 mm dia Aluminium alloy round conductor & 10 mm Copper bonded conductor at cross/Tee junction. Test Parameter a) Mechanical Load b) Electrical Test c) ENvironmental Test Tested for IEC 62561-1 CAPE Type: CCSS 8-10 / equivalent.

Supply and Installation of Aluminium Straight conductor connector for interconnecting 8mm Aluminium conductor to meets the requirement of IS/IEC 62305. Test Parametres: a) Mechanical Load b) Electrical Resistivity c) Environmental Test Tested as per IEC 62561-1 CAPE Type: CJ 8 / equivalent.

Supply and Installation of Expansion Joint with connector to compensate the expansion and contraction of Solid Round Al. Conductor during temperature variations. Expansion Joint should be consider at every 20 mtr length of straight horizontal air termination and connected at both the end with use of straight connector conductor. CAPE Type: EPC 8 / equivalent.

Supply and Installation of Vertical airterminal with corner protecting measure along with suitable mounting arrangements to protect the corners and edges of terrace area and to avoid side flashes. Test Parametres for 500 mm vertical air terminal a) Electrical Resistivity b) Tensile strength c) Condition of bend d)Condition of adhesion e) Copper coating thickness f) Condition of Salt mist Tested as per IEC 62561-2 CAPE Type: VAT CR 14.2 CB / equivalent.

Supply and Installation of air termination rod of 4 mtr length of material AlMgSi of diametre ø 16/10 mm crimped on both the ends(Tappered Type). The rod shall be mounted with stone and fixing accessories . Test Parameter for 4 mtr vertical air terminal a)ELectrical Resistivity b) Tensile Strength c) Condition of Salt Mist Tested as per IEC 62561-2. CAPE Type: VATF4 / equivalent.

Supply and Installation Folding Seam Conductor Holder CAPE Type: FSCH 14-8 / equivalent.

Supply & Installation of Lightning counter - LCD screen shows the number of lightning strikes, hour and date of lightning events Buttons enable TIME/DATE setting and log viewing. Replaceable battery, working life minimum five years, Complies with IEC/EN 62561-6. CAPE Type No: PRO LER / equivalent.

Supply and Installation of Stainless Steel 304 grade Test Joint with enclosure to interconnect between 8 mm Al. round conductor to 10 mm copper bonded round conductor. Test Parameter: Salt Spray Test for test joint plate -No sign of Corrosion Tested as per IEC 62561-1 CAPE Type: TJRRE - G1 / equivalent.

Supply and Installation of Rust resistant non corossive 10 mm dia Copper Bonded Steel round conductor used for Earth termination inside the concrete and soil. Test parameter: a) Short circuit current test for copper bonded conductor:Test 6 kA ratings, as per cross sectional area for 1 sec (IS3043/IEEE80); b)Electrical Resistivity before & after salt mist spray test: 0.25µΩm max. c)Tensile Test 290 to 510 N/mm². d)Adhesion no peel or crack & Bend test no seperation of Cu, e)Cu Coating thickness min. 70µm. Tested as per IEC 62561-2. CAPE Type: SRC 10 CU / equivalent.

Supply and Installation of Stainless steel SS 304 Grade Conductor Holder for fixing the 8 -10 mm dia round conductor on the wall . Test Parameter: a) Mechanical Load b) Environmental Test Tested as per IEC 62561-4 CAPE Type: CH 8-10 / equivalent.

Supply and Installation of CAPE make / equivalent. UL Listed Maintenance Free Copper bonded Earth rod of 3048mm length having the dia of 17.2 mm with copper coating thickness of 254 microns. The rod has been tested for Dimension, Marking, Tensile Strength, Salt mist, coating thickness, Electrical resistivity test before and after corrosion test as per IEC 62561-2 & UL 467/ equivalent.. CAPE Type No. CBR 1410 (Article No. 300 010)/ equivalent. Supply and Installation of CAPE make earth enchancing mineral compound tested for leaching and TCLP with NABL accredited Lab as per IEC 62561-7 -25 kg CAPE Type: PROSAN 12.5 (Article No. 300 830) / equivalent. Supply and Installation of CAPE make Earth rod clamp made for terminating cable / flat conductor. CAPE Type / equivalent : ERC 1417 SS (Article No. 300 463) + CAPE Type / equivalent : CPES 8 (Article No. 401 504) Supply and Installation of CAPE make / equivalent Earth Chamber Inspection Pit made up of Plastic withstand load of 60kN CAPE Type: EC 290 (Article No. 300852)

CAPE-RAYCAP / equivalent Surge Protection Devices Type : 1+2 Location : Main Panel Voltage Protection Level -(L - N) / (N - PE) Up-1400 V / 1500 V Impulse Discharge Current (10/350 μs)-(L - N) / (N - PE) Iimp -12.5 kA / 50 kA Nominal Discharge Current (8/20 μs) -(L - N) / (N - PE) In-12.5 kA / 50 kA Response Time -(L - N) / (N - PE) tA-< 25 ns / < 100 ns >>Fault Indication- Red Flag MODEL NO: PROTEC T1-300-3+1-L-E-R

CAPE - RAYCAP / equivalent Surge Protection Device Category : Type 2+3 Location: Sub panels >>Tested TOV 120 min as per IS/IEC 61643-11 >>Nominal AC Voltage - 230V >>Maximum Continous Operating Voltage - 440V >>Nominal Discharge Current (8/20 μs),, In- 10 KA >>Maximum Discharge Current (8/20 μs), Imax - 20kA >>Voltage Protection Level for Type 2+3, Up - 1700 V >>Response Time , tA- < 25 ns >>Fault Indication- Red Flag MODEL NO: PROTEC T2 CM -440-4+0-L-E

Design, Engineering, supply, fabrication, erection, testing, commissioning and handing over of 1No 13 persons capacity Gearless with machine room passenger lift (KONE / OTIS /JOHNSON) as per the following technical specifications with free Guarantee period of one year from the date of commissioning. Technical specifications: 1. Type of lift : passenger lift 2. Capacity of lift : 13 persons capacity passenger lift 884 Kg 3. Speed : 1.50 Meter/Sec 4. Type of Drive: specific variable voltage variable frequency V3F drive with enhanced ride comfort and leveling functions. 5. No. of floors: Ground + 7 floor 6. Leveling Accuracy: High level 7. Construction of Car: 18 SWG high quality stainless steel car, powder coated stretcher impact protection car size 2000 mm x 1100 mm. 8. Position of machine: Directly above the lift well 9. No. of landing entrance: 8Nos 10. No. of car entrance: one in front only 11. Car entrance door: power operated. 12. Car entrance door: power operated center opening sliding 18 SWG stainless steel vandal proof door with provision for emergency key opening at all landings. 13. Lift well : existing (as per IS) 2500mm wide x 1900mm Deep

28. Automatic Rescue device: To facilitate the landing of the lift to the nearest floor at the time of power failure. This shall consist of suitable type battery system with charger, invertor, under voltage protection system etc., complete with all accessories. 29. Provision of intercom with phone: To be provided by lift contractor with one handset in the lift car and another handset in the lift machine room with telecom exchange unite with one trunk and three extension linked proton 103 matrix telecom unit and required length of single twisted pair with thickness of 0.5 mm to 1 mm connecting the handsets and telecom exchange unit. 30. Lift License: Preparation of Drawing, payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate as per lift act should be done by lift contractor. 31. Floor announciator with music. 32. Special features: a. Infra red door sensor with full height screen. b. Full width half height rear panel mirror. c. Tubular stainless steel hand rail in cars. d. Voltage stabilizer for circuit control. e. Stainless. Steel signal fixtures. f. Vandal proof S.S. Button with S.S. cover g. SS door frames for landing doors. h. VF door operator. i. Call Register signa

j. Stainless steel facia plate for car operating panel and landing fixtures. k. On – Off switch for fan and light l. Over load warning indicator with audio announcement 33. Other standard features: Over speed governor, phase failure and phase reversal relay, T. Guide brackets for car and counter weight, rubber padding under winding unit, motor of adequate capacity, electro mechanical door locks emergency keyside supporting angles, motor over load protection devices final limit switch main suspension ropes counter weights lifting joist for mounting the machineries 34. Site testing in accordance with IS 14665 should be carried out at the time of handing over. 35. Supply of operation and maintenance manual with necessary tools for operation. 36. Guarantee: Free Guarantee for the materials and workmanship of equipments complete should be offered by lift firm for a period of one year from the date of commissioning.(SR)

Design, Engineering, supply, fabrication, erection, testing, commissioning and handing over of 1No 13 persons capacity Gearless with machine room passenger lift (KONE / OTIS /JOHNSON) as per the following technical specifications with free Guarantee period of one year from the date of commissioning. Technical specifications: 1. Type of lift : passenger lift 2. Capacity of lift : 13 persons capacity passenger lift 884 Kg 3. Speed : 1.50 Meter/Sec 4. Type of Drive: specific variable voltage variable frequency V3F drive with enhanced ride comfort and leveling functions. 5. No. of floors: Ground + 8 floor 6. Leveling Accuracy: High level 7. Construction of Car: 18 SWG high quality stainless steel car, powder coated stretcher impact protection car size 2000 mm x 1100 mm. 8. Position of machine: Directly above the lift well 9. No. of landing entrance: 9Nos 10. No. of car entrance: one in front only 11. Car entrance door: power operated. 12. Car entrance door: power operated center opening sliding 18 SWG stainless steel vandal proof door with provision for emergency key opening at all landings. 13. Lift well : existing (as per IS) 2500mm wide x 1900mm Deep

28. Automatic Rescue device: To facilitate the landing of the lift to the nearest floor at the time of power failure. This shall consist of suitable type battery system with charger, invertor, under voltage protection system etc., complete with all accessories. 29. Provision of intercom with phone: To be provided by lift contractor with one handset in the lift car and another handset in the lift machine room with telecom exchange unite with one trunk and three extension linked proton 103 matrix telecom unit and required length of single twisted pair with thickness of 0.5 mm to 1 mm connecting the handsets and telecom exchange unit. 30. Lift License: Preparation of Drawing, payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate as per lift act should be done by lift contractor. 31. Floor announciator with music. 32. Special features: a. Infra red door sensor with full height screen. b. Full width half height rear panel mirror. c. Tubular stainless steel hand rail in cars. d. Voltage stabilizer for circuit control. e. Stainless. Steel signal fixtures. f. Vandal proof S.S. Button with S.S. cover g. SS door frames for landing doors. h. VF door operator.

i. Call Register signal j. Stainless steel facia plate for car operating panel and landing fixtures. k. On – Off switch for fan and light l. Over load warning indicator with audio announcement 33. Other standard features: Over speed governor, phase failure and phase reversal relay, T. Guide brackets for car and counter weight, rubber padding under winding unit, motor of adequate capacity, electro mechanical door locks emergency keyside supporting angles, motor over load protection devices final limit switch main suspension ropes counter weights lifting joist for mounting the machineries 34. Site testing in accordance with IS 14665 should be carried out at the time of handing over. 35. Supply of operation and maintenance manual with necessary tools for operation. 36. Guarantee: Free Guarantee for the materials and workmanship of equipments complete should be offered by lift firm for a period of one year from the date of commissioning.

Supply and fixing of WT bulk head fitting with guard suitable with 7W/9W LED bulb.

Supply and run of 3 of 2.5 sqmm (36/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable heavy gauge MS conduit pipe on wall and ceiling with continuous earth wire connection of 2.5 sq.mm wire with painting of suitable colour. (For Lift Well Light Control)

Supply and Fixing of 16A Two-way switch in suitable MS box on wall with earth connection.(HIGHER END)

Supply and Fixing of Metal one way FP Enclosure with 63A FP RCBO 30 mA on wall with earth connection.(HIGHER END)

Supply and clamping of 4 x 16 sq.mm PVC CopperLTUG armoured LTUG cable on post or on wall with MS Clamps.

RISING MAIN - Power Sandwich Plug in busduct riser with Aluminum Busbars, Polyester insulation, Protective part, epoxy painted EG sheet housing, single bolt expandable joints between sections, System-415V, 3Phase, 4Wire with 100% Neutral and integral 50% Earth, Degree of Protection: IP55. Rating: 1600A 4P, 65KA. The rate shall be included End box, flange connection, Fire wall frame assembly, Flexible joint & Vertical spring etc.,

Straight Length (Note:Plug in Hole (Each floor 3 Plug in Box)

Vertical Fixing Clips

Cable Entry Box C/W Flanged End

End Feed Unit

Design, manufacture, installation, testing & commissioning of 1600A, 50KA, 4P EDO type ACB with End feed Unit (Neutral isolable) with RYB indication lamps and CBCT with ELR for incoming, with 1set of R/G/T Indication lamp & control MCB, 1-96sq.mm combined digital type meter (KW/KWHr/V/A with RS 485) with 3Nos 1600/5A, CL.0.5,15VA Current tranformer and with necessary supports for busbar. Suitable Busbar terminal arrangement shall be provided for : Out going cable entry for 5R X 3.5C x 400Sq.mm Al Arm Cable.

Tap of Units (TOU) Supply, Installation, Testing and Commissioning of 630A 4P MCCB with Front drive kit

Tap of Units (TOU) Supply, Installation, Testing and Commissioning of 400A 4P MCCB with Front drive kit

RISING MAIN - Lighting & Essential Sandwich Plug in busduct riser with Aluminum conductors, Polyester insulation, Protective part, epoxy painted EG sheet housing, single bolt expandable joints between sections, System-415V, 3Phase, 4Wire with 100% Neutral and integral 50% Earth, Degree of Protection: IP55. Rating: 630A 4P, 65KA. The rate shall be included End box, flange connection, Fire wall frame assembly, Flexible joint & Vertical spring etc.,

Straight Length (Note:Plug in Hole (Each floor 3 Plug in Box)

Vertical Fixing Clips

Cable Entry Box C/W Flanged End

End Cap

Design, manufacture, installation, testing & commissioning of 630A, 50KA, 4P EDO type ACB with End feed Unit (Neutral isolable) with RYB indication lamps and CBCT with ELR for incoming, with 1set of R/G/T Indication lamp & control MCB, 1-96sq.mm combined digital type meter (KW/KWHr/V/A with RS 485) with 3Nos 630/5A, CL.0.5,15VA Current tranformer and with necessary supports for busbar. Suitable Busbar terminal arrangement shall be provided for : Out going cable entry for 2R X 3.5C x 400Sq.mm Al Arm Cable.

Tap of Units (TOU) Supply, Installation, Testing and Commissioning of 250A 4P MCCB with Front drive kit

Supply, Installation, Testing, Commissioning and Handing over of 35kWp Grid connected roof top Solar PV System Scheme complete as detailed below. Design, Engineering, Manufacturing, Procurement, Supply of materials to project site, project management, installation of mechanical equipment, cabling & appurtenances, instrumentation and electrical system and other equipment, as detailed in this section.Scope of the proposal a)Solar Modules (Multicrystalline-as per IEC specifications) b)Mounting Structure (Design to Chennai Coastal ambient condition) c) Inverter, distribution boards, junction boxes, cables d) Earthing for Solar modules and inverter e)Lightning Protection f) Installation and commissioning g)Project management h)Liasioning for approval from MNRE

TECHNICAL SPECIFICATIONS 1. SOLAR PV MODULES AND ARRAY (i) Only indigenous modules shall be used in the Solar module shall be Crystalline (Mono/Poly) (or) Thin Film (or) Concentrator PV modules type. The peak power output of the PV Module shall be min 100Wp under STC. Module Voc shall be minimum 21V. The total array capacity shall not be less than required capacity and this shall be operating at the required DC voltage. The power output of the PV module must be reported under standard test conditions (STC). I_V curve of the sample module should be submitted. (ii) The mechanical structure shall withstand gusts of wind / cyclonic wind up to 150km/hr from back side of the panel. (iii) The offered modules must conform to the latest edition of any of the following IEC/ equivalent BIS Standards for PV module design qualification and type approval: Crystalline Silicon Terrestrial PV Modules : IEC 61215/IS14286 Thin Film Terrestrial PV Modules : IEC 61646/ Equivalent IS(Under Dev.) Concentrator PV Modules & Assemblies : IEC 62108 (iv) In addition, the modules must conform to IEC 61730 1- requirements for construction & Part 2 - requirements for testing, for safety qualification or Equivalent IS (Under Dev.) (v) PV modules must also qualify Salt Mist Corrosion Testing as per IEC 61701/IS61701.(vi) SPV modules shall be certified by NABL/IECQ accredited test centre. The bidder shall submit appropriate certificates. (vii) Protective devices against surges at the PV module shall be provided. Low voltage drop bypass diodes shall be provided. (viii) Module Junction box (weather proof), where the module terminals shall be interconnected and output taken, shall be designed for long life out door operation in harsh environment

as per the relevant BIS specifications and protected against surges. It should have a provision for "Opening" for replacing the cable, if required. (ix) PV modules used in solar power plants must be warranted for output wattage, which should not be less than 90% at the end of 10 years and80% at the end of 25 years. (x) Each PV module must use a RF identification tag (RFID), which must contain the following information: a.Name of the manufacturer of PV Module b.Name of the manufacturer of Solar cells c.Unique Serial Number & Model No. of the module d.Month and year of the manufacture (separately for Solar cells and module) e. Country of origin ( separately for solar cells and module) f.. I-V curve for the module g. Peak Wattage of the module ,Im, Vm and FF for the module h. Date and year of obtaining IEC PV module qualification certificate i. Name of the test lab issuing IEC certificate j. Other relevant information on traceability of solar cells and module as per ISO 9000 series RFID shall be mandatorily placed inside the module laminate. A distinctive serial number starting with NSM will be engraved on the frame of the module or screen printed on the tedlar sheet of the module.

1.1 ORIENTATION AND TILT OF PV MODULES Modules shall be North -South oriented at the Tilt Angle of 11° "13° 2. MOUNTING STRUCTURES The PV modules will be mounted on fixed metallic structures of adequate strength and appropriate design, which can withstand load of modules and high wind velocities up to 200 km per hour. The support structure used in the power plants will be hot dip Galvanized Iron (G.I).

The "Mounting Structure" should have the following features: • Solar Panel Main Structure to be suitable for fixation in the Car and Two wheeler parking area main frame. The modules support structure shall be Mild Steel /hot dipped Galvanized (atleast 120 micron) Iron for holding the PV modules. The size of angle iron should not be less than 50x50x5mm.Each panel frame structure shall be so fabricated as to be grouted on roof on its legs. Baseframestructure of solar pv module should be framed with the main structure in the parking area. modules at a given orientation, absorb and transfer the mechanical loads to the ground properly and shall withstand maximum wind speed of 200 km/hr All nuts and bolts should be made of good quality Stainless Steel.The structure should be designed to allow easy replacement of any module.The array structure shall be so designed that it will occupy minimum space without sacrificing the output from the SPV panels. The minimum clearance of the lowest part of the module structure and the developed ground level shall not be less than 500 mm. The minimum clearance required from the parapet wall of the roof & in between row of panels is min 2 feet for cleaning the panels & servicing.

The bidder shall specify installation details of the PV modules and the support structures with appropriate diagrams and drawings. The work shall be carried out as per the designs approved by the procuring entity. 3. JUNCTION BOXES The junction boxes shall be dust proof, vermin and waterproof and made of FRP / Thermo Plastic. The terminals shall be connected to copper bus bar arrangement of proper sizes. The junction boxes shall have suitable cable entry points fitted with cable glands of appropriate sizes for both incoming and outgoing cables. Suitable markings shall be provided on the bus bar for easy identification and cable ferrules shall be fitted at the cable termination points for identification. Each main junction box shall be fitted with appropriate rating blocking diode. The junction boxes shall be of reputed make.

4. POWER CONDITIONING UNIT (PCU) The PCU shall also house MPPT (Maximum Power Point Tracker), an interface between Solar PV array & the Inverter, to maximize Solar PV array energy input into the System. PCU including MPPT & protection conform to IEC 61683/IS 61683, IEC 60068-2(1,2,14,30)/Equivalent BIS Std., 1 DC Array Input Operating Voltage 20% to +15% of the DC Array input voltage in Sl.No. 1 above 2 Type of Solar Charge Controller MPPT Based Solar Charge Controller 3 Switching device MOSFET/IGBT based 4 Output Wave Form Pure Sine Wave Output 5 Total Harmonic Distortion < 3% with resistive load 6 Output Voltage 230+ 3 % in case of 1 phase PCU 400+ 3 % in case of 3 phase PCU 7 Output Frequency 50 Hz. ± 0.5 Hz 8 Power Factor > 0.9 9 PCU efficiency > 90% at nominal voltage & power 10 Idle Current < 4% of rated capacity

11 Regulation Line regulation & Load regulation - 2 % 12 Overload Features 150% for 1 minute 13 Cooling Forced Air cooling, with temperature controlled cooling fan 14 Operating temperature 0 - 50 °C 15 Relative Humidity 95% Maximum 16 LED /LCD Display Indications :Display shall indicate system functional parameters and protection functional indicator 17 Data monitor and display controls RS485, Ethernet OR RS232 connectivity 18 Protections 1) Input over voltage 2)Low/high frequency 3) Short circuit 4) Under/over output voltage 5) Over Temperature 6) Grid Input under voltage / over voltage with auto recovery 7) DC disconnect device 8)DC reverse polarity 9) Anti Islanding Protection as per the standard

19 Enclosure Protection IP 21 (for indoor) as per IEC 529 20 Safety 1. IEC 62103 2. IEC 62109 Part 1 & 2 3. Galvanic Isolation at input & output through transformer INVERTER: The power conditioning unit/inverter should be grid interactive and also DG set interactive if necessary. Inverter output should be compatible with the grid frequency. Nominal AC O/P voltage and frequency : 415V, 3-ph, 50Hz Accuracy of AC voltage control Output frequency : +1% Output frequency : 50 Hz Accuracy of frequency control : +0.1% Grid Frequency Synchronization range : +3Hz Maximum Input DC Voltage : inverter Dependant Ambient temperature considered : 40˚C Humidity : 95% Non condensing Protection of Enclosure:IP-20(Min) Indoor, IP-65(Min) Outdoor Grid Frequency Tolerance range : +3% Grid Voltage tolerance : -20% & +15% No-load losses : <1% of rated power Inverter efficiency(minimum) : >95% THD : <3%

INVERTER: The power conditioning unit/inverter should be grid interactive and also DG set interactive if necessary. Inverter output should be compatible with the grid frequency. Nominal AC O/P voltage and frequency : 415V, 3-ph, 50Hz Accuracy of AC voltage control Output frequency : +1% Output frequency : 50 Hz Accuracy of frequency control : +0.1% Grid Frequency Synchronization range : +3Hz Maximum Input DC Voltage : inverter Dependant Ambient temperature considered : 40˚C Humidity : 95% Non condensing Protection of Enclos ure:IP-20(Min) Indoor, IP-65(Min) Outdoor Grid Frequency Tolerance range : +3% Grid Voltage tolerance : -20% & +15% No-load losses : <1% of rated power Inverter efficiency(minimum) : >95% THD : <3% 5.DC & AC Switches a. DC SIDE (i) MCB of suitable rating shall be provided for connection and disconnection of array & PCU for maintenance purpose. (ii) Switches and Circuit Breakers on DC side shall be DC rated or they shall be sufficiently de-rated, if AC rated switches are used.

7. Earthing and Lightning Protection: Earthing: The array structure of the PV yard shall be grounded properly using adequate number of earthing kits. All metal casing or shielding of the power plants shall be thoroughly grounded to ensure safety of the solar power plants. Lightning: The SPV power plants shall be provided with lightning &over voltage protection. The main aim in this protection shall be to reduce the over voltage to a tolerable value before it reaches the PV or other sub system components. The source of over voltage can be lightning, atmosphere disturbances etc 8.INTEGRATION OF PV POWER WITH GRID: The output power from SPV would be fed to the inverters which converts DC produced by SPV array to the AC and feeds it into the main electricity grid after synchronization. In case of grid failure, or low or high voltage, solar PV system will be out of synchronization and will be disconnected from the grid. Once the DG set comes into service PV system will again be synchronized with DG supply and load requirement would be met to the extent of availability of power 4 pole isolation of inverter output with respect to the grid/DG power connection need to be provided.

9.GRID ISLANDING:PV system software and control system will be equipped with islanding protection. In addition to disconnection from the gird (islanding protection i.e. on no supply), under and over voltage conditions will adequate rating fuses, fuses on inverter input side (DC) as well as output side (AC) for overload and short circuit protection and disconnecting switches to isolate the DC and AC system for maintenances as needed.

Fuses of adequate rating will also be provided in each solar array module to protect them against short circuit. A manual disconnect 4 pole isolation switch beside automatic disconnection to grid would have to be provided at utility end to isolate the grid connection by the utility personnel to carry out any maintenance. 10.OPERATION AND MAINTENANCE MANUAL An Operation and Maintenance Manual, in English and Tamil, should be provided with the solar PV power plants. The following minimum details must be provided in the Manual: About Photo Voltaic & PV Module Clear instructions about mounting of PV module. DO's and DONT's, Clear instructions on regular maintenance and Trouble Shooting of the power plants. Name & address of the person or Centre to be contacted in case of failure or complaint. The equipment/materials and the whole system should be operated by trained personnel of the purchaser after giving training. The periodical maintenance, cleaning of the Solar Panels should be done by the firm/Supplier/Contractor for a period of five years.

11.Grid – Tie Solar PV System i)Solar PV Modules ii)Structure for mounting modules iii)Inverters iv)Cabling to PV module to Inverter (a)Bench mark cost (MNRE) Rs. 100/per wattp (b)MNRE Subsidy: 30% (c)Cabling for grid interaction (d)Segregation of mains (e)Installation and Commissioning (f)Periodical inspection, cleaning of panels and maintenance of the system for five years 12.WARRANTY (i) Solar panel at 90% efficiency- 10 years (ii)Solar panel at 80% efficiency- 25 years (iii)All other equipments - 5 years

WARRANTIES & GUARANTIEES: The goods supplied under this contract are new, unused, of the most recent or latest technology and incorporate all recent improvements in design and materials. This warranty will also be covering the rectification of any and all defects in the design of equipment, materials and workmanship including spare parts for the guarantee period specified by MNRE/TEDA from the date of commissioning. All the Guarantees/Warrantees of the different components will be transferred to Owner of the project 13. Make of the Components (i)Indigenous MNRE approved Multi Crystalline modules – Tata Power/Emvee/Alpex/Su-Kam/Vikram/Equivalent. (ii)Off grid Inverter (PCU) – Refusol /SMA / Schneider/Su-Kam/VISPRA//Equivalent.

VRF UNIT Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/ Variable Refrigerant Volume air cooled Outdoor units suitable for cooling , having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R410A Refrigerant, vibration isolators, with suitable foundation etc. complete as required . The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V+/-10%, 3Phase ,50Hz AC power supply.The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 ( Scope of work includes Charging of Addittional Refrigerent to the entire circuits as required.) All units shall have provision for communicating with BMS

DUCTABLE UNIT Design ,supply , installation, testing and commissioning of 11.0TR nominal capacity factory assembled Air-cooled Condensing unit fixed with energy efficient scroll compressor along with grooved copper tube/aluminium fins air cooled condensor coil with anticorrosion coatings,liquid ,accumulator, low noise alumimium propeller condenser fan with Fan motor etc all suitably assembled neatly in heavy duty GSS sheet metal cabinet and duly powder coated as per specification .the unit to include built in safety controls like HP/LP switch power quality protector ,in built thermal / temperature protection. (carrier make"Design ,supply , installation, testing and commissioning of DX 11TR nominal capacity factory assembled Air-cooled Condensing unit fixed with energy efficient scroll compressor along with grooved copper tube/aluminium fins air cooled condensor coil with anticorrosion coatings,liquid ,accumulator, low noise alumimium propeller condenser fan with Fan motor etc all suitably assembled neatly in heavy duty GSS sheet metal cabinet and duly powder coated as per specification. the unit to include built in safety controls like HP/LP switch power quality protector ,in built thermal / temperature protection. ( VRF 11TR DUCTABLE UNIT) 12.8TR DUCTABLE UNIT- VRF INDOOR UNIT

Hiwall Unit HIWALL SPLIT /Supply erection, testing and commissioning of 2.0 TR (6000 K.cal/Hr) ABS Plastic Split type Air conditioner with copper coil conforming to IS 1391 (Part-2) 1992 with Amdt No. 1 to 2 fitted with Rotory compressor operating on Non CFC Refrigerant suitable for wall mounting for operation on 230V, 50HZ single phase AC supply Cooling Dehumidifying Air Circulating Filtering 2.02 TR HIWALL UNIT

GI Ducting Supply, installation, balancing and commissioning of factory fabricated GSS duly powder coated sheet in milk white colour metal eleptical ducting inclusive of collars as per OEM complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports, collars etc. as per approved drawings and specifications of following sheet thickness complete as required. ( Suitable supports, Fasteners and necessary scaffoldings etc. are included in the item) Make: Sail / Jindal / TATA / Lloyds

Thickness 1.00 mm sheet (20G)

Thickness 0.80 mm sheet (22G)

Thickness 0.60 mm sheet (24G)

Supply and Installation of Canvass connections for indoor units and ventilation fans with all necessary accessories etc.

INSULATION Supplying & Providing thermal insulation for duct of Air-Conditioned area using 19 mm thick non-fibrous, CFC free, closed cell, elastomeric nitrile rubber foamed insulation in pre-formed sheets only with the adhesives supplied by the insulation manufacturer.( The insualtion shall be provided inside Periphery of duct.)"Supply and fixing of acoustic insulation 15mm thick with Nitrile rubber Open Cell type inclusive of suitable adhesive for nitrile rubber" (Make: Armaflex / Kflex / Thermobreak / supreme) 19MM -ACOSTIC

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed 9MM cell Nitrile rubber (Class “O”) insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. 9mm -THERMAL

supply and Installation of Under deck insulation for exposed roofs 50mm thick thermocole with aluminium foil faced and all accessoriesIN all AHU ROOMS

GRILLS & DIFFUSERS Supplying & fixing of powder coated extruded aluminium Supply Air JET NOZZELLS (250 MM ~450MM)

GRILLS & DIFFUSERS Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but with volume control dampers complete as required.

GRILLS & DIFFUSERS Supplying & fixing of powder coated extruded aluminium LINEAR SLOT DIFFUSERS - (2SLOT ~ 1SLOT~3SLOT) with louvers

VRF-COPPER REFRIGERANT PIPING Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories,

6.35 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick (1/4")

19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick (3/4")

12.7 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick (1/2")

22.2 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19mm thick(7/8")

34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19mm thick(11.3/8")

41.27 mm dia (OD) (Hard drawn) with tube (11.5/8") thickness 1.62 mm

Insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as (Make: Armaflex / Kflex / Thermobreak / supreme) 19mm THICK NITRILE RUBBER INSULATION FOR ALL COPPER PIPES

GAS TESTING COMMISSIONING OF R410 A

TJOINTS & REMOTE CONTROLLERS & BMS Supplying, installation, testing & commissioning of VRV/VRF Refnut Joints / Branch kits/ T-joints / Refnut Headers of all sizes / shapes as per the actual piping layout for this VRV/VRF project.

VRF DRIVE KIT FOR AHU WITH REMOTE CONTROLLERS-

BMS CONTROLER FOR EACH FLOOR

DRAIN PIPING Supplying and fixing following sizes of regid / flexible UPVC drain pipe with suitable clamps etc., for drain water connections from AC indoor units of all types & models upto the location as desired by the Engineer-In-Charge complete with all accessories etc., , as required. 40mm dia regid/ flexible UPVC pipe with nitrile rubber insulation.

WIRING AND CABLING Control cable between indoor & outdoor communication purpose- Wiring should be insulation on PVC materials as required - 1.5SQMM 2 CORE SHIELDED copper flexible CABLE Make: Polycab / Gloster / Universal

WIRING AND CABLING POWER Cable between - ODU and Terminal DB 4core 10Sqmm with nessasry PVC materials as required-Make: Polycab / Gloster / Universal

WIRING AND CABLING GI TRAY FOR Both Copper piping and control cabling between IDU & ODU including with Hanging materials nessary rods and Bolts etc

Control Panel for ODU-Supply ,Installation ,Testing and commissioning of 63A ,4P,MCB for Iincomer and out going one no 63A,4P, 30mA ELCB with weather proof suitable outdoor type box at terrace floor level outdoor unit for power supply.

CIVIL WORKS AND OTHERS - Civil concrete Works for ODU

CIVIL WORKS AND OTHERS - SCUFF HOLDING WORKS

CIVIL WORKS AND OTHERS - LIFTING & SHIFTING FOR BOTH IDU & ODU

CIVIL WORKS AND OTHERS - INSTALLATION CHARGES FOR VRF UNITS

VENTILATION SYSTEM Supply, Installation, Testing and Commissioning of cabinet type Inline fan made out of galvanized sheet complete with Forward curved Centrifugal fans with Belt/direct driven TEFC motors with class F insulation, inlet and outlet flange and flexible canvass at inlet and outlet for duct connection (300 mm length) and access door, and all necessary accessaries with louvers and bird screen, Mounting Bracket, Stand or Hanging arrangement and electrical cable connection necessary for Fan Unit. (Make: Kruger / Nicotra / Greenheck / Flaktwood / Elta- Exhaust Air Fan (Toilet)

Fresh Air Fan With Prefilter (Toilet) 8500 cfm 75 mm SPWG (2W + 2S)

Exhaust Air Fan (Toilet)4500 cfm 75 mm SPWG (2W + 2S)

Supply and erection of 100 Amps Capacity dust and vermin proof floor mounting cubical panel board fabricated out of 16 SWG CRCA sheet for outer body,stiffness and doors and with supply and fixing of following interior switches with centre bus bar chamber and horizontal no of switches side to side on both sides of bus bar chamber with cable chamber of the extreme right end and top of Panel with two coats of quality paint over one coat of zinc oxide primer superscription of incoming and outgoing feeding cable details, capacity of switches etc., with white paint and 2nos metallic danger board affixed complete on suitable base channel supports on 6Nos of 0.45m channel legs to satisfy the latest CEIG rules with the following switches conforming to IS specifications.

Supply and erection of 100 Amps Capacity dust and vermin proof floor mounting cubical panel board fabricated out of 16 SWG CRCA sheet for outer body,stiffness and doors and with supply and fixing of following interior switches with centre bus bar chamber and horizontal no of switches side to side on both sides of bus bar chamber with cable chamber of the extreme right end and top of Panel with two coats of quality paint over one coat of zinc oxide primer superscription of incoming and outgoing feeding cable details, capacity of switches etc., with white paint and 2nos metallic danger board affixed complete on suitable base channel supports on 6Nos of 0.45m channel legs to satisfy the latest CEIG rules with the following switches conforming to IS specifications.

The incoming and outgoing switches should be connected to the bus with the following copper flats. 1) 100A FP switch with 1" x 1/8" tinned copper flat 2) 32A TPN switch with No.8 SWG copper The switches should be separated from the bus bars by 6 mm thick hylum sheet and all switches should be properly earthed by solid copper flat as per IE rules and CEIG specification. Providing Rubber Beading for All Doors

Supply and erection of 200 Amps Capacity dust and vermin proof floor mounting cubical panel board fabricated out of 16 SWG CRCA sheet for outer body,stiffness and doors and with supply and fixing of following interior switches with centre bus bar chamber and horizontal no of switches side to side on both sides of bus bar chamber with cable chamber of the extreme right end and top of Panel with two coats of quality paint over one coat of zinc oxide primer superscription of incoming and outgoing feeding cable details, capacity of switches etc., with white paint and 2nos metallic danger board affixed complete on suitable base channel supports on 6Nos of 0.45m channel legs to satisfy the latest CEIG rules with the following switches conforming to IS specifications.

The incoming and outgoing switches should be connected to the bus with the following copper flats. 1) 200A FP switch with 1" x 1/4" tinned copper flat 2) 32A TPN switch with No.8 SWG copper wire The switches should be separated from the bus bars by 6 mm thick hylum sheet and all switches should be properly earthed by solid copper flat as per IE rules and CEIG specification. Providing Rubber Beading for All Doors

Supply and erection of 315 Amps Capacity dust and vermin proof floor mounting cubical panel board fabricated out of 16 SWG CRCA sheet for outer body,stiffness and doors and with supply and fixing of following interior switches with centre bus bar chamber and horizontal no of switches side to side on both sides of bus bar chamber with cable chamber of the extreme right end and top of Panel with two coats of quality paint over one coat of zinc oxide primer superscription of incoming and outgoing feeding cable details, capacity of switches etc., with white paint and 2nos metallic danger board affixed complete on suitable base channel supports on 6Nos of 0.45m channel legs to satisfy the latest CEIG rules with the following switches conforming to IS specifications.

The incoming and outgoing switches should be connected to the bus with the following copper flats. 1) 315A FP switch with 1 1/4" x 1/4" tinned copper flat 2) 32A TPN switch with No.8 SWG rigid copper 3) 63A TPN switch with No.8 SWG rigid copper The switches should be separated from the bus bars by 6 mm thick hylum sheet and all switches should be properly earthed by solid copper flat as per IE rules and CEIG specification. Providing Rubber Beading for All Doors

Supply and erection of 315 Amps Capacity dust and vermin proof floor mounting cubical panel board fabricated out of 16 SWG CRCA sheet for outer body,stiffness and doors and with supply and fixing of following interior switches with centre bus bar chamber and horizontal no of switches side to side on both sides of bus bar chamber with cable chamber of the extreme right end and top of Panel with two coats of quality paint over one coat of zinc oxide primer superscription of incoming and outgoing feeding cable details, capacity of switches etc., with white paint and 2nos metallic danger board affixed complete on suitable base channel supports on 6Nos of 0.45m channel legs to satisfy the latest CEIG rules with the following switches conforming to IS specifications.

The incoming and outgoing switches should be connected to the bus with the following copper flats. 1) 315A FP switch with 1 1/4" x 1/4" tinned copper flat 2) 32A TPN switch with No.8 SWG rigid copper 3) 63A TPN switch with No.8 SWG rigid copper The switches should be separated from the bus bars by 6 mm thick hylum sheet and all switches should be properly earthed by solid copper flat as per IE rules and CEIG specification. Providing Rubber Beading for All Doors

Supply and erection of 630 Amps Capacity dust and vermin proof floor mounting cubical panel board fabricated out of 16 SWG CRCA sheet for outer body,stiffness and doors and with supply and fixing of following interior switches with centre bus bar chamber and horizontal no of switches side to side on both sides of bus bar chamber with cable chamber of the extreme right end and top of Panel with two coats of quality paint over one coat of zinc oxide primer superscription of incoming and outgoing feeding cable details, capacity of switches etc., with white paint and 2nos metallic danger board affixed complete on suitable base channel supports on 6Nos of 0.45m channel legs to satisfy the latest CEIG rules with the following switches conforming to IS specifications.

The incoming and outgoing switches should be connected to the bus with the following copper flats. 1) 630A FP switch with 1" x 3/4" tinned copper flat 2) 100A TPN switch with 30mm x 6mm tinned copper flat. The switches should be separated from the bus bars by 6 mm thick hylum sheet and all switches should be properly earthed by solid copper flat as per IE rules and CEIG specification. Providing Rubber Beading for All Doors

Supply, Clamping, testing & commissioning of the following sizes of 1.1KV grade Aluminium / Copper Conductor armoured power cables Insulation of XLPE above 25Sqmm and Class A PVC below 25Sqmm laid on trays, ceilings, walls trenches, ground etc., with necessary clamps, cable ties, fasteners, identification tags, cable marking as required. Cost of sand, bricks, excavation should not be included in the rate quoted & measured separately.

3 1/2C X 400 Sqmm Al.Ar.XLPE Cable

3 1/2C X 240 Sqmm Al.Ar.XLPE Cable

3 1/2C X 150 Sqmm Al.Ar.XLPE Cable

3 1/2 C X 70 Sqmm Al.Ar.XLPE Cable

3 1/2C X 35 Sqmm Al.Ar.XLPE Cable

3.5C X 25 Sqmm Al.Ar.XLPE Cable

Supply & fixing of Cable Gland of following AL/CU armoured power cables with necessary double compression brass glands, AL/CU. terminal sockets, insulation tapes, fasteners, earthing clips & connecting the clip to main earth bus with suitable bare copper wire complete accessories as required.

3 1/2C X 400 Sqmm Al.Ar.XLPE Cable

3 1/2C X 240 Sqmm Al.Ar.XLPE Cable

3 1/2C X 150 Sqmm Al.Ar.XLPE Cable

3 1/2 C X 70 Sqmm Al.Ar.XLPE Cable

3 1/2C X 35 Sqmm Al.Ar.XLPE Cable

3.5C X 25 Sqmm Al.Ar.XLPE Cable

Supply & end termination of following AL/CU armoured power cables with necessary double compression brass glands, AL/CU. terminal sockets, insulation tapes, fasteners, earthing clips & connecting the clip to main earth bus with suitable bare copper wire complete accessories as required.

3 1/2C X 400 Sqmm Al.Ar.XLPE Cable

3 1/2C X 240 Sqmm Al.Ar.XLPE Cable

3 1/2C X 150 Sqmm Al.Ar.XLPE Cable

3 1/2 C X 70 Sqmm Al.Ar.XLPE Cable

3 1/2C X 35 Sqmm Al.Ar.XLPE Cable

31/2 C X 25 Sqmm Al.Ar.XLPE Cable

Cable Trays & MS Supports Supply & installation of Hot -dip galvanized cable rack system made of 2mm thick sheet steel folded with two longitudinal side rails connected by rungs at regular intervals of following sizes with necessary Tee's, Vertical/ Horizontal Bends, expansion anchor fasteners, coupler plates, coupling fasteners, including supply & grouting of supports as required at site. The supports should be painted with black enamel paint over a coat of anti corrosive primer. (Tray shall be measured along the central axis of the cable tray, 1000mm above sizes are fabricated by MS items)

750mm width Ladder Tray 100mm Height

600mm width Ladder Tray 100mm Height

450mm width Ladder Tray 50mm Height

Supply, fabrication& installation of MS channels / angles, flat sections for cable trays, tray supports, Panel / DB mounting frames, insert plates, Busduct supports etc., as directed at site. All fabricated items shall be painted with 2coats of black enamel paint over a coat of approved paint.

Equipment Earthing Supply & erection of 100mm dia Cast Iron earth electrode of10' length buried in ground as per IS with necessary connecting clamps, watering arrangement &fasteners etc. The pit shall be filled with alternate layers of salt &charcoal. The rates shall include excavation of the pit, construction of masonry chamber, providing heavy duty concrete cast slab, painting & making etc.,& as per the technical specification.

Supply & laying of following size Copper & GI Flats and Wires with necessary supports and fasteners etc.

60x10mm Copper flat

50x10mm Copper flat

50x6mm Copper flat

25x6mm Copper flat

25x3mm Copper flat

50X6mm GI Flat

25X6mm GI Flat

25x3mm GI flat

Supply and run of No.8 SWG Copper wire for DB and HVAC outdoor earth connection.

Supply & fixing of Earth bus chamber comprising of 50 X 6mm tinned copper of minimum 500mm length with stand off insulators mounted inside a powder coated enclosure with cover.

CMK Projects Private Ltd., (BID ID -1161433)

ABIRAMI ENGINEERING CONSTRUCTION AND CO (BID ID -1163968)