"Provision of Distributed Electronic Interlocking at Hisar station over Bikaner Division"

Item Breakup - 1-SOR SCHEDULE

Per For Station with routes more than 200 routes Functional Vital Bit

1.00 751843.88 architecture as supplied upto 6 (six) line station. It includes transportation of material from consignee's depot to the site, erection and grouting of EI Relay Racks, fixing and wiring of all the interfacing relays (Vital & Non-Vital), installation and wiring of Microprocessor equipments, interface equipments, power supply equipments and all other associated accessories to make complete EI system to be functional. Note: (i) Technical Requirements are attached with tender document (ii) Contractor has to arrange simulator/simulation testing panel for testing and commissioning by Selection Table and Square Sheet for each Signalling function.(iii) Installation, wiring, testing and commissioning of EI system will be done by OEM after following all the guidelines/directives issued by RDSO from time to time. Inspection: Consignee Inspection charges: None Payment terms: 100% after commissioning NWR-PROJ-JP-S AND T/NORTH WESTERN RLY Design, manufacture and supply of Hot Standby Architecture Electronic Interlocking (EI) system complete as per RDSO specification No. RDSO/SPN/192/2019 Ver. 2 or latest, as per technical requirement & tentative approved Signalling Plans & Diagrams. Electronic Interlocking (EI) system m a i n l y c o n s i s t i n g of Central Processing Equipment, Interface Equipment/Relays etc as per requirements, Dual operator Industrial Grade VDU panel (42" LED) with Redundancy (Hot stand-by dual VDU Normally one system online and other system in standby mode), All Interfacing Relays suitable for EI, interconnecting cables and Jumper wires, Industrial grade maintenance Terminals (32'' LED with UPS minimum 1 hr back up), required power supply converters for EI equipments, Housing for EI equipments and Relay Racks, fuses, screw less disconnecting type terminals, fixture mounting arrangements and accessories necessary to make the EI system functional as per approved signalling plan. The tenderer should furnish complete details of cards/ modules/ sub-modules connectors etc. for each station. Supply of 10% Essential spares of the EI equipments subject to minimum one of each type mainly consisting of processor, cards/ module, interface relay etc. Item wise detailed break up with unit and quantity to be provided in separate annexure. (THIS ITEM SHALL BE USED ONLY FOR ALTERTION WORK IN EXISTING EI) Inspection: RDSO Inspection charges: Borne by Railways Payment terms:100% after Supply

Per For Station with routes less than 100 Functional Vital Bit

3.00 653241.66 supplied as per supply item in item no. 01010400 above of Chapter 1 of this SOR including transportation from Consignee's depot to site. The works and materials for installation, wiring, testing and commissioning, grouting, cutting of floors, walls, refilling of the same, re-plastering, required CC/ masonry works, fixing/ placing/ laying of insulated ladders/ casing-capping/ cable trays/ RCC/GI pipes / Cables, termination of cables with lugs/ connectors, painting/ lettering are to be provided/ done by the contractor for the equipments supplied vide item no. 01010400 of Chapter 1 of SOR. This also covers the networking of built in EI Data loggers of all the stations to monitor the system to any other places where desired by Engineer-in-charge. (THIS ITEM SHALL BE USED ONLY FOR ALTERTION WORK IN EXISTING EI) Note: Installation shall be complied to RDSO Technical Advisory Note No STE/E/TAN/3012 dtd. 28.08.2014. Installation, wiring, programming, testing and commissioning of Operator VDU in Hot stand-by with Redundancy. Any Equipments/cards/Modules required for Hot stand-by with Redundancy shall be supplied and Installed by the Contractor. Note: This also includes supply of Two nos. of composite computer and printer table (Godrej work station table) and one no Godrej make operator chair model PCH7001. Termination of indoor/ PIJF cables in relay room on relays, tag blocks, CT racks as per approved wiring diagram including alterations/ modifications as required at site. Soldering to be done at all required termination. Dressing/ lacing of wiring shall be done neatly with help of dressing thread / plastic self lock strip of suitable size. The tools/ equipments/ materials/ simulation boards required for testing shall be supplied / fabricated by contactor. This includes replacement of modules/ cards/ LEDs/ equipments going defective during testing. Necessary power supply boards with required capacity plugs, sockets, surge and lightning protection boxes shall be supplied and installed by the contractor. 230V supply shall be arranged by Railways. In case supplies are required to be extended, from Power room / relay room then same shall be extended by the contractor with his own materials such as 1X16 sq mm wires, cables, lugs, RCC/GI pipes, insulated ladders etc. After ST/LT testing, Factory Acceptance Tests (FAT) and Square Sheet testing system should be fault free while submitting to Railways, otherwise suitable necessary action can be taken by Engineer-in-charge. Inspection: Consignee, Inspection charges: None, Payment terms: 100% after commissioning.

1.00 104575.40 also includes supply of Laser Printer (Only branded). The workstation should be capable of reconfiguring the system in case of any alteration in yard interlocking in future. Technical Specifications should be attached with the tender document by Tendering authority. Inspection: Consignee Inspection charges: None Payment terms: 100% after supply

1.00 151338.52 of hardware and software for EI system should be supplied for stations. (This includes tools required for EI maintenance sorts of crimping, insertion, removal, general purpose tools like screw drivers, spanners, PCB extractor, temp. controlled soldering iron, wire cutter, nose pliers etc. & measuring instruments with carrying case/ holders/ cabinet for technicians/ J.E. for testing, Maintenance and repair at site). Each set comprises of the following :- * Crimping tool for all types of special cable assembly used in EI system. * Insertion tool for all types of special cable assembly used in EI system. *Removal tool for all types of special cable assembly used in EI system. * Digital multi-meter (Fluke 111 or better) * Steel cabinet/ Almira, Size: 1980mm height, 915 mm width and 485 mm depth (Godrej Make/Jalaram) of good quality to store tool, spare cards and documents. * Steel Book rack Size: 1850mm height, 900 mm width and 316 mm depth for keeping documents. (Godrej Make/Jalaram) * Clamp Earth Tester. (as per specs mentioned in tender document.) * Clamp Current Meter (fluke 362 or superior) * Ferrule tagging printer for cable/wires (Supported label tape sizes: 6 / 9 / 12 / 18 / 24 mm). Inspection: Consignee Inspection charges: None Payment terms: 100% after supply

30.00 Repairs & Troubleshooting of EI system. (Hard copies of training material/ course modules to be given to each participant). Inspection: Consignee Inspection charges: None Payment terms: 100% after execution

10.00 Troubleshooting of EI system. (Hard copies of training material/ course modules to be given to each participant). Inspection: Consignee Inspection charges: None Payment terms: 100% after execution NWR-PROJ-JP-S AND T/NORTH WESTERN RLY

1.00 interlocked gate with all corrections as per approved SWRD & approved SIP. For these all-technical corrections, editing, grammatical correction etc. are to be carried out and one rough print to be given to railways for approval before printing, as required for final processing of CRS sanction. This also includes preparation of maintenance cards in format provided by Rly. Inspection: Consignee Inspection charges: None Payment terms:100% after execution.

1.00 DIGLOT form (or similar software) as per extant Rly practice. The required SWR in English will be provided by the contractor and has been covered separately in item no. 01011800 of Chapter 1 of SOR. Inspection: Consignee Inspection charges: None Payment terms:100% after execution.

6.00 form as per Railway practice. Inspection: Consignee Inspection charges: None Payment terms:100% after execution.

2.00 consist of (i) executive revolving bearing series low back-floating chair with normal arms cushioned chair-01 Nos. (ii) Executive table size 1650x900x728 mm with 3 drawers one side locker- 01 no. (iii) visitor chair seat & back cushion with high density foam with plastic PVC handle capsule type painted back-03 nos. Inspection: Consignee Inspection charges: None Payment terms:100% after execution.

1.00 copies of prints with soft copy will be submitted to Railway for checking. If alterations are suggested/proposed by Railways then again two copies of prints will be submitted for advance approval after carrying out all the alterations as suggested/proposed by the Railways. Tracings will be submitted for all the diagrams mentioned above for the purpose of approval by Railway prior to commissioning of station. Inspection: Consignee Inspection charges: None Payment terms:100% after execution.

50.00 insulated indoor Railway signalling cable @40<45@Core/40-Core) of (1/0.6) sqmm as per RDSO Spee. No. IRS/S-76/89 (Amnd.2 or latest) for wiring between relay room and SM's/Panel room & Relay room to DP in SM office for block working. This also includes supply of PVC insulated jumper wires of multi strand 16/.2 mm, tinned in all colours as per RDSO Specn.No.IRS-S- 76/89(Amnd.2 or latest). This item will include bringing all the power supplies from power room to respective bus bars on relay racks by using 10/6 sqmm copper flexible wire as per instructions of engineer incharge. This will include wiring between control panel and relay room if required. All wiring will be done as per standard practice of North Western Railway with neat dressing & threading. The item includes supply & wiring of tag block, fuse with bases (G- Type and ND Type) and all other related material required for complete indoor wiring in relay room. Inspection: Consignee Inspection charges: None Payment terms:100% after execution. Supply & Installation of Modular power supply arrangement for VDU and industrial PC (Embedded PC) with input and output redundancy arrangement and Hot pluggable Modules as per RDSO specification. Make Gallant or similar. One set consists of 1. Input O- ring diode module with potential free -1 No contacts (PFC) for two 110 V DC sources from IPS and single 110 VDC bus Qty 1 No. 2. Isolated Inverters (Master / slave) - Input-110 V DC Output: 120 V AC/220V A500VA - 02 Nos. 3. Isolated DC-DC convertors- Input: 110 v DC Output: 24 V DC/ 10A, Qty -10Nos. 4. 3 U SS rack with back panel mother board /front panel power connectors inverter auto change over switch and all required over switch and all required protection circuits (3U height for main rack 132.5mm +/-10% & 1U height for mounting 44.5mm +/- 10%) Qty - 1 No. Make Gallant or similar. (This item is for Operating VDUs of EI system) Inspecting Agency : (i)for inverters and converters : RDSO (ii) for other items : Consignee Inspection Charges: (i) Borne by Railways (ii) None

2.00 after Commissioning Total 88916156.40 Item- 2 Data Logger, RTU, FEP, CMU, FAS and Networking Accessories S No. Item No Description of Item Unit Qty Rate Amount

4.00 2003980.10 analog inputs as per RDSO Spec. No. IRS (S) 99/2006 or latest with laser printer 22 ppm (Only branded HP/Brother/Canon). It includes supply of all the items required for complete indoor relay room wiring from data logger to relay rack tag blocks, drawing/extension of power supply upto Data Logger. It includes relay room door lock checking arrangement, commercial power supply monitoring arrangement & monitoring of DG sets, ELD, IPS, UFSBI, BI, interlinking and networking of Data logger. It also includes supply of leased line MODEM, suitable online UPS (minimum 6 hours backup) and other interfacing cards, if required for networking of Data Logger. This also includes supply of one no. composite computer and printer table (Godrej work station table or similar) for keeping processor module and one number Godrej operator chair Model PCH7001 or similar. Note: Total numbers of relays and other signalling functions/gears required to be wired as per list circulated vide RDSO Letter No. STS/E/Data logger dtd.12.09.2011 or latest guidelines. Inspection: RDSO Inspection charges: Borne by Railways Payment terms:100% after supply NWR-PROJ-JP-S AND T/NORTH WESTERN RLY

4.00 146220.70 Logger System with 1024/1280/ 4096 digital and 32 analog inputs as per RDSO Spec. No. IRS (S) 99/2006 or latest. It cover complete indoor relay room wiring from data logger to relay rack tag blocks, drawing/extension of power supply upto Data Logger. It includes relay room door lock checking arrangement, commercial power supply monitoring arrangement & DG sets, ELD, IPS, UFSBI, BI interlinking and networking of Data logger. All material required for wiring, networking, power supply monitoring, door-locking arrangement etc will be supplied by contractor. Note: Total numbers of relays and other signalling functions/gears required to be wired as per list circulated vide RDSO Letter No. STS/E/Data logger dtd.12.09.2011 or latest guidelines. Networking of data logger includes extraction of data report from test room. For networking, required communication channel (Quad/ OFC cable) will be arranged/provided by Rly in SM/ASM's room or in OFC Porta Cabin and it will be extended by contractor upto location of data logger by using CAT-5/6 telecom cable with proper casing and capping. The contractor will supply all the material like CAT-5/6 telecom cable, casing & capping, nuts, bolts etc. The final commissioning will be done after filling up of Pre- Commissioning checklist (circulated by RDSO) with the OEM representative. Inspection: Consignee, Inspection charges: None Payment terms:100% after commissioning

1.00 4096 digital inputs at a station. Inspection: Consignee, Inspection charges: None Payment terms:100% after supply.

1.00 for data logger upto 4096 digital inputs. Inspection: Consignee, Inspection charges: None Payment terms:100% after commissioning

1.00 197325.10 specification of FAS should be got approved from the Engineer in charge before supply. Note: The Specification of FAS shall be as per technical specification given in contract Agreement or higher version as approved by Engineer In-Charge. (Technical specification shall be provided in tender documents.) Inspection: Consignee Inspection charges: Borne by Railways Payment terms:100% after supply

1.00 per Technical Specifications. The specification of FAS should be got approved from the Engineer in charge before supply. Note: The Specification of FAS shall be as per technical specification given in contract Agreement or higher version as approved by Engineer In-Charge. (Technical specification shall be provided in tender documents.) Inspection: Consignee, Inspection charges: None Payment terms:100% after commissioning

1.00 Data Logger equipments. This includes supply of all equipment / accessories required for the purpose e.g. modems and network accessories. Inspection: Consignee, Inspection charges: None Payment terms:100% after supply

1.00 Logger equipments. This includes supply of all equipment / accessories required for the purpose. Inspection: Consignee, Inspection charges: None Payment terms:100% after commissioning Total 8942989.52 Item- 3 Indoor Relays, Timers, Flasher, KLCR S No. Item No Description of Item Unit Qty Rate Amount

120.00 board (base plate), connectors and retaining clips etc and conforming to BRS- 930 and RDSO Specn.No.IRS:S-34 & S-23 or latest. The interlocking code for this unit shall be "ABCDE". Inspection: - RDSO Inspection charges: - Borne by Railways Payment Terms: - 100% after supply.

120.00 board (base plate), connectors and retaining clips etc and conforming to BRS- 930 and RDSO Specn.No.IRS:S-34 & S-23 or latest. The interlocking code for this unit shall be "ABCDF". Inspection: - RDSO Inspection charges: - Borne by Railways Payment Terms: - 100% after supply.

70.00 plug board (base plate), connectors and retaining clips etc and conforming to BRS-960 and RDSO Specn.No.IRS:S-34 & S-23 or latest. The interlocking code for this unit shall be "ACDEK". Inspection: - RDSO Inspection charges: - Borne by Railways Payment Terms: - 100% after supply.

70.00 plug board (base plate), connectors and retaining clips etc and conforming to BRS-960 and RDSO Specn.No.IRS:S-34 & S-23 or latest. The interlocking code for this unit shall be "ACEHJ". Inspection: - RDSO Inspection charges: - Borne by Railways Payment Terms: - 100% after supply.

70.00 complete with plug board (base plate), connectors and retaining clips and conforming to BRS-935A and RDSO Specn.No.IRS:S-34 & S-23 or latest. The interlocking code for this unit shall be "ABDEG". Inspection: - RDSO Inspection charges: - Borne by Railways Payment Terms: - 100% after supply.

25.00 with plugboard (base plate), connectors and retaining clips etc and conforming to BRS:930 & RDSO letter no STs/E/Relays/UEA/PI dated 30.05.97 Annexure I and RDSO Specn.No.IRS:S-34 & S-23 or latest. The interlocking code for this unit shall be "BDEKX". Inspection: - RDSO Inspection charges: - Borne by Railways Payment Terms: - 100% after supply.

245.00 board (base plate), connectors, retaining clips etc and conforming to BRS:941A STS/E/RELAYS/AC LIT LED SIGNAL/09-2002, Amdt.-1 and RDSO Specn.No.IRS:S-34 & S-23 or latest. The interlocking code for this unit shall be "ABDHK". Inspection: - RDSO Inspection charges: - Borne by Railways Payment Terms: - 100% after supply.

15.00 RDSO Inspection charges: - Borne by Railways Payment Terms: - 100% after supply. NWR-PROJ-JP-S AND T/NORTH WESTERN RLY

85.00 complete with plug board, retaining clip and connectors. Conforming to BRS:931A & RDSO letter no STs/E/Relays/UEA/PI dated 30.05.97Annexure II and IRS:S34 & IRS:S23 or latest. The interlocking code for this unit shall be "CDEKY". Inspection: - RDSO Inspection charges: - Borne by Railways Payment Terms: - 100% after supply.

20.00 plug board, retaining clip & connectors as per RDSO/SPN/84 Ver 2.0 or latest. The interlocking code for this unit shall be "ABEJX". Inspection: - RDSO Inspection charges: - Borne by Railways Payment Terms: - 100% after supply.

400.00 plug board (base plate), connectors, retaining clips etc and conforming to BRS-931A and RDSO Specn.No.IRS:S@45"44@ S-23 and S-60 or latest. The interlocking code for this unit shall be "ABDGH". Inspection: - RDSO Inspection charges: - Borne by Railways Payment Terms: - 100% after supply.

100.00 plug board (base plate), connectors, retaining clips etc and conforming to BRS-931A and RDSO Specn.No.IRS:S@45"44@ S-23 and S-60 or latest. The interlocking code for this unit shall be "ABDFH". Inspection: - RDSO Inspection charges: - Borne by Railways Payment Terms: - 100% after supply.

100.00 plug board (base plate), connectors, retaining clips etc and conforming to BRS:939A & 966(Appendix F2) or latest. The interlocking code for this unit shall be "FGHKX". Inspection: - RDSO Inspection charges: - Borne by Railways Payment Terms: - 100% after supply.

100.00 board (base plate), connectors, retaining clips etc and conforming to BRS- 933A and RDSO Specn.No.IRS:S@45"44@ S-23 & S 60 or latest. The interlocking code for this unit shall be "ABDEJ". Inspection: - RDSO Inspection charges: - Borne by Railways Payment Terms: - 100% after supply.

40.00 (base plate), connectors, retaining clips etc and conforming to BRS- 943 and RDSO Specn.No.IRS:S-34 & S-23 or latest. The interlocking code for this unit shall be "BCEJK". Inspection: - RDSO Inspection charges: - Borne by Railways Payment Terms: - 100% after supply.

40.00 different ward combinations and contact configuration 4F/4B with 2 extra ward plates and with case, RDSO spec no. RDSO/SPN/219/2016 ver 1.0 or latest, confirming to IRS S-23, S-34 & S@45<44@ IRS S:46. Inspection: - Consignee. Inspection charges: - None. Payment Terms: - 100% after supply. Total 8822383.95 Item- 4 Relay Racks, CT Racks, Tag Blocks, Terminal, Fuses, Indoor Cables and Jumper Wires S No. Item No Description of Item Unit Qty Rate Amount

10.00 16/0.2 mm (0.5sqmm) as per IS 694:2010 and RDSO Specn.No.IRS:S-76/89 (Amnd-3) or latest. Each coil should be of 100/200/500 meters length. Colour of the wire which is required will be specified by the Engineer incharge. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

200.00 per IS:694:2010 or latest, 84 conductor each dia 0.30 +/- 0.01 with insulation thickness of 0.8 mm and nominal conductor resistance of 3.3 ohms/km and test parameters as per RDSO Specn.No.IRS:S-76/89(Amnd.3) or latest. Colour of the wire which is required will be specified by the Engineer incharge. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways(ii) None Payment Terms: 100% on Supply

200.00 per IS:694:2010 or latest, 140 conductor each dia 0.30 +/- 0.01 with insulation thickness of 1.0 mm and nominal conductor resistance of 1.91 ohms/km and test parameters as per RDSO Specn.No.IRS:S-76/89(Amnd.3) or latest. Colour of the wire which is required will be specified by the Engineer incharge. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

200.00 per IS:694:2010 or latest, 127 conductor each dia 0.40 +/- 0.01 with insulation thickness of 1.0 mm and nominal conductor resistance of 1.21 ohms/km and test parameters as per RDSO Specn.No.IRS:S-76/89(Amnd.3) or latest. Colour of the wire which is required will be specified by the Engineer incharge. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs(ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board.Inspection Charges: (i)Borne by Railways(ii) NonePayment Terms: 100% on Supply

200.00 IS:694:2010 or latest, 197 conductor each dia 0.40 +/- 0.01 with insulation thickness of 1.2 mm and nominal conductor resistance of 0.78 ohms/km and test parameters as per RDSO Specn.No.IRS:S-76/89(Amnd.3) or latest. Colour of the wire which is required will be specified by the Engineer incharge. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply NWR-PROJ-JP-S AND T/NORTH WESTERN RLY

200.00 per IS:694:2010 or latest, 277 conductor each dia 0.40 +/- 0.01 with insulation thickness of 1.2 mm and nominal conductor resistance of 0.554 ohms/km and test parameters as per RDSO Specn.No.IRS:S-76/89(Amnd.3) or latest. Colour of the wire which is required will be specified by the Engineer incharge. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

4.00 digital & analog Inputs (1280 digital inputs and 32 analog inputs). It includes supply of PVC insulated indoor Railway Signalling cable (1/0.6 sqmm Dia), 60- Core/40-Core/Single Core as per RDSO Specn.No.IRS:S-76/89(Amnd.3) or latest, PVC insulated jumper wires multi strand, tinned in all colours as per RDSO Spec. No. IRS: S-76/89 (Amnd.3) or latest. The item also includes supply & wiring of Modular disconnect terminals /Tag Blocks as per RDSO Specn.No.IRS:S-77/2006 (Rev.1) or latest and RDSO Drg.No.SA-24751 or latest. The wiring for getting potential free contacts of relays for complete PI/RRI/EI installation including points, tracks, signals, panel, power supply, IPS, SSDAC, TLBI, LC Gates, crank handle control etc will be done by contractor. All material will be supplied by contractor except the relays. The Relays will be supplied by Railway. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs(ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i) Borne by Railways (ii) None Payment Terms: 100% on Installation & commissioning

1.00 Specn.No.IRS:S-76/89 (Amnd.3) or latest. Note: wires colours will be specified/decided by site Engineer incharge. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

1.00 Specn.No.IRS:S-76/89 (Amnd.3) or latest. Note: wires colours will be specified/decided by site Engineer incharge. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

8.00 scaffolding and suitable grouting arrangements. The relay racks shall be supplied & completed with scaffolding, bus bars, fuse strips, fuses (G/NDT), fuse bases, resistors, capacitors, insulators and 200-Way tag blocks with poly carbonate covers, grouting bolts, tripods etc. It includes supply of Tag Blocks as per RDSO Specn.No.IRS:S-77/2006 (Rev.1) or latest and RDSO Drg.No.SA- 24751. The top of relay racks will be supported through an angle iron with one side fixed on supporting wall. Inspection: (i) RITES if value of item in work more than 10 lakhs (ii) Consignee Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

8.00 with scaffolding and suitable grouting arrangements. The relay racks shall be completed with scaffolding, bus bars, fuse strips, fuses (G/NDT), fuse bases, resistors, capacitors, insulators and 200-Way tag blocks with poly carbonate covers, grouting bolts, tripods etc. It includes fixing of Tag Blocks as per RDSO Specn.No.IRS:S-77/2006 (Rev.1) or latest and RDSO Drg.No.SA-24751. The top of relay racks will be supported through an angle iron with one side fixed on supporting wall. After installation of relay racks, one coat of paint will be done by contractor before fixing the fuses. Scaffolding should include 1 relay rack position as spare at every Station/ Level Crossing Gate for future expansion. Inspection: Consignee Inspection Charges: None Payment Terms: 100% on execution

10.00 complete along with fitting arrangements and also with arrangement for fixing four 8-way terminal strips/ Screw less terminals/ ARA terminals on each row having 16 such rows. Supply of 8 way terminal strips/ Screw less terminals / ARA terminals not covered under this item. Cable termination rack shall be Powder Coated. Inspection: (i) RITES if value of item in work more than 10 lakhs (ii) Consignee if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

10.00 supports, scaffolding and suitable grouting arrangements with installation of 8 way/ARA terminals /Screw less connectors, Tag blocks & other necessary accessories etc. The work shall be done as per approved plan, extant practice o n NWR & the instruction of Rly engineer at site. Inspection: Consignee Inspection Charges: None Payment Terms: 100% on Commissioning.

5000.00 Specn.No.IRS:S-75/2006 (Rev.2) or latest and RDSO Drg. No. SA-23741A (Alt. 4) or latest. Inspection: RDSO. Inspection Charges: Borne by Railways. Payment Terms: 100% on supply.

800.00 23748 (Alt. 4) or latest and RDSO Specn.No.IRS:S-75/2006 (Rev.2) or latest. Inspection: RDSO. Inspection Charges: Borne by Railways. Payment Terms: 100% on supply. Supply of indicating type fuse inserts with holder (material will be supplied only from approved vendors of RDSO). Inspection: Consignee Inspection Charges: Borne by Railways. Payment Terms: 100% on supply.

Numbers Supply of indicating type fuse inserts without holder (material will be supplied only from approved vendors of RDSO). Inspection: Consignee Inspection Charges: Borne by Railways. Payment Terms: 100% on supply. NWR-PROJ-JP-S AND T/NORTH WESTERN RLY

80.00 as per RDSO Specn.No.IRS:S-78/92 or latest and Capacity - 2/4/6/10A/16A/20A A m p . (material will be supplied only from approved vendors of RDSO). Inspection: Consignee Inspection Charges: Borne by Railways. Payment Terms: 100% on supply.

10.00 (Rev.1) or latest & Drg.no.SA-24751 & 52. Requirement of each type shall be specified by Engineer-in-charge. NOTE: In case ABB type relays proposed to be used with 100-way block then Two 100-way Tag Block will be considered as one 200-way Tag Block. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

10.00 (IRS :S-77/2006 (Rev.1) or latest & Drg.no.SA-24753. Requirement of each type shall be specified by Engineer-in-charge. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

1.00 185872.85 (0.6mm Dia) conforming to IRS:76/89(Amd3) or latest. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs(ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

18000.00 location boxes, cable termination rack in relay room, station building, Conductor generator room etc. The item includes dressing of cables and wires with dressing threads as per standard practice. All material required for this item will be supplied by contractor. The outdoor cable shall be terminated in Relay Room, DG Room, ASM Room etc under supervision and instructions issued by Engr. incharge of the work. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after execution

0.50 119946.30 (0.6 mm Dia) conforming to IRS:76/89(Amd3) or latest. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

0.50 191525.62 mm Dia) conforming to IRS:76/89(Amd3) or latest. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply Supply of Disconnect Terminal Block, Screw less type, as per RDSO Spec. No. RDSO/SPN/189/2004(Modular Terminal Blocks, Fuse Terminal Blocks &Miniature fuse link of international standard for Railway signaling) With latest amendments. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

8000.00 in-put & Two out-put) The colour will be decided by Engineer - in - Charge. (Preferably In Blue, Red & Grey Colors in the ratio of 1:2:3)

1000.00 site requirement.

300.00 per site requirement.

200.00 1mm/0.039 in thickness un-slotted type as per site requirement.

16.00 as per RDSO/SPN/209/2012 rev.1 with latest amendments. One Automatic Module changeover Unit comprise 32 nos. of external Non-Deteriorating Type or 'G' type fuses from 0.6 Amp to 4 Amp capacities which are in signalling circuits. System shall have 8 cards with monitoring arrangement of 4 fuses in one card. Inspection:(i) RDSO/RITES: if value of item in work more than 10 lakhs (ii) Consignee: subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs or as per extant policy. Inspection charges:(i) Borne by Railways (ii) None Payment Terms: 100% after supply.

4.00 as per RDSO/SPN/209/2012 rev.1 with latest amendments. One Automatic Module changeover Unit comprise 24 nos. of external Non-Deteriorating Type or 'G' type fuses from 4 Amp to 10 Amp capacities which are in signalling circuits. System shall have 6 cards with monitoring arrangement of 4 fuses in one card. Inspection: (i) RDSO/RITES: if value of item in work more than 10 lakhs (ii) Consignee: subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs or as per extant policy. Inspection charges: (i)Borne by Railways (ii) None Payment Terms: 100% after supply.

20.00 (FACS). This includes provision of common Buzzer & indication at ASM Room & Module ESM Duty Room and painting of fuse details. This also includes fabrication of frame for installation of FACS at Station/ LC gate where installation of relay racks not feasible. Inspection: Consignee Inspection charges: None Payment Terms: 100% on commissioning Total 3974989.10 NWR-PROJ-JP-S AND T/NORTH WESTERN RLY Item- 5 Power Supply Equipments, Batteries, Surge protection, Program Switches, DG sets S No. Item No Description of Item Unit Qty Rate Amount Installation, Wiring and testing of Integrated Power Supply System. This includes power distribution connection to bus bars and relay racks in the room with contractor's own wiring materials and fabrication and fixing of AC/DC power distribution board made on 10mm thick Phenolic hylam sheets or any standard make with connections suitable for 32 A. Wiring to be done considering site requirement, depending upon the load with suitable wires, lugs & glands as per instructions of Engineer-in-charge. The work includes installation of Thermo flasher relay, ELD's, fixing & wiring of change over switch (program switch) for selection of DG set supply (DG1 & DG2) and wiring of change over switch (program switch) for selection of mains or DG supply. This item also includes supply & fixing of ladder along the wall for carrying power supply wires/cables from IPS room to Relay room/power room etc. Any masonry work required will be carried out by contactors own material. It includes transportation of IPS from consignee depot to work site/station/ LC gate. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after execution

2.00 147243.76 as per RDSO Specn.No.IRS:S-86/2000 (Amnd.4) or latest. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% on Supply

1.00 191848.03 Amps as per RDSO Specn.No.IRS:S-86/2000 (Amnd.4) or latest. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% on Supply Supply of uncharged Low Maintenance Lead Acid (LMLA) secondary cell, shelf mounting type conforming to RDSO Specn.No.IRS:S-88/2004 or latest with inter cell connectors, nuts and bolts etc. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after Supply.

Numbers Charging of Lead Acid Batteries with contractors own battery grade sulphuric acid and distilled water with minimum two charge - discharge cycles, installation of charged batteries in groups & their connection & wiring. The work shall be done as per extant practice of N.W.Rly & instruction of Engineer- in-charge. Detailed measurements of initial charging shall be recorded jointly by contractor & Rly's site-in-charge. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Execution.

2.00 Generator set of 12.5 KVA/ 15 KVA Note: (i) New DG set alongwith all accessories will be provided by Railways (if any required).(ii) All masonry work required for installation of DG set will be done by contractor under supervision/ instructions of site engineer incharge. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution.

1000.00 sandwiched between two antistatic layer thickness of 2mm ± 01mm self-fire Foot extinguishing as approved by engineer incharge. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after execution.

4.00 /drawings approved by the site engineer incharge. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after supply.

4.00 standard NFC-17-102. It shall work on early streamer emission principle & shall be made of stainless steel with a T of 60 microseconds. Non resettable type counter shall also be supplied to count the number of lightening occurrences. It also includes supply of electrolytic copper tape of 25mmX2mm or better for connecting class A device to the earth pit. This includes installation, testing and commissioning of Class A device on the top of the building. This device shall be installed at suitable height on the roof of the building using a GI mast as per instructions of Railway engineer at Site. The device shall be connected to earth pit using a copper tape of 25mm x 2mm or better. This copper tape shall be run firmly only the site of the mast with the help of spacers. It shall also be ensured that the down conductor shall not touch the building throughout. the down conductor shall be connected to the earth electrode using exothermic welding. A counter shall be installed at appropriate space to count the number of occurrences. All the accessories like spacers, welding material etc. required for installation shall be arranged by the contractor. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after commissioning. Total 2201787.30 Item- 6 Points Machine S No. Item No Description of Item Unit Qty Rate Amount

60.00 complete with lock detector and slides for lock detector non -trailable to operate on 110V DC rotary locking with crank handle universal type as per RDSO Spec. No. IRS:S-24/2002 (Amnd 1) RDSO Drg. No. S-10800 (Alt.5) with junction box telescopic. The motor will be as per RDSO Spec. No. IRS: S-37/82 (Amnd. 3) with RDSO Drg. No. S-10910. This includes supply of Set of tools as per para 20.1 & 20.2 of RDSO SPECN. NO. IRS:S-24/2002 (Amnd 1) 20.1 The following set of tools in a suitable tool box shall be supplied along with every set of eight point machines or less. i) Hand operated square drive socket wrenches of 12.5 mm driving square (short type) as per IS: 7381 for M8, M10, M12 & M18 threads. (One 250 mm long 12.5 mm square extension bar as per IS: 7991 alongwith compatible Tee handle Square drive as per IS: 7975 suitable for above socket wrenches shall also be provided.) ii) Open jaw wrenches (spanners) for M10, M12, M20, M24 & M33 threads as per IS: 2028. iii) Adjustable wrench. iv) Screw driver 300 mm long. 20.2 Junction box and two numbers of telescopic pipes of approved type shall be supplied as an integral part of the point machine. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after Supply. NWR-PROJ-JP-S AND T/NORTH WESTERN RLY

5.00 complete with lock detector and slides for lock detector non -trailable to operate on 110V DC rotary locking with crank handle universal type as per RDSO Spec. no. IRS:S-24/2002 (Amnd 1) RDSO Spec. no S-10800 (alt.5) with junction box telescopic. The motor will be as per RDSO Spec. no. IRS: S-37/82 (amnd. 3) with RDSO Spec. no. S-10910. This includes supply of Set of tools as per para 20.1 & 20.2 of RDSO Spec. no. IRS:S-24/2002 (Amnd 1). 20.1 The following set of tools in a suitable tool box shall be supplied along with every set of eight point machines or less. i) Hand operated square drive socket wrenches of 12.5 mm driving square(short type) as per IS: 7381 for M8, M10, M12 & M18 threads.(One 250 mm long 12.5 mm square extension bar as per IS: 7991 alongwith compatible Tee handle square drive as per IS: 7975 suitable forabove socket wrenches shall also be provided.) ii) Open jaw wrenches (spanners) for M10, M12, M20, M24 & M33 threads as per IS: 2028. iii) Adjustable wrench. iv) Screw driver 300 mm long. 20.2 Junction box and two numbers of telescopic pipes of approved type shall be suppliedas an integral part of the point machine. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after Supply.

40.00 bracket 'D' bracket insulation for IRS point machine - One set comprises of (a) Side plate LH to Drg. No. S-3266 - 1 No. (b) Side plate RH to Drg. No. S-3265 - 1 No. (c) Insulating bush to Drg. No. S-3199 - 4 Nos. (d) Insulating washer to Drg. No. S-8640 - 4 Nos., 2. Split-Stretcher bar 2.1 Insulation for Leading stretcher bars (BG) each set comprising of (a) Insulating plate for leading insulated stretcher bars BG as per RDSO Drg. No. T-10384 - 2 Nos. (b) Insulating bushing for leading insulated stretcher bars for BG as per RDSO Drg. No. T-10535- 4 Nos. (c) Insulating Washer for insulated stretcher bar BG as per RDSO Drg. No. T-10371 - 6 Nos. 2.2 Insulation for following stretcher bars BG. Each set comprising of: (a) Insulating side plate for insulated stretcher bars BG as per RDSO Drg. No. T-10367 - 3 No. (b) Insulating bushing for insulated stretcher bars BG as per RDSO Drg. No. T-10368 - 6 Nos. (c)Insulating washer for insulated stretcher bars BG as per RDSO Drg. No. T10371 - 12 Nos 3. Gauge tie plates (52 Kg/60Kg as per site requirement) Insulation for (BG) complete with insulating bush and washereach set comprising of: (a) Insulating plate for insulated tie plate BG as per RDSO Drg. No. T-10372-1 No. (b) Insulating bushing for insulated stretcher bar BG as per RDSO Drg. No. T10368 - 3 Nos. (c) Insulating Washer for insulated stretcher bar BG to IRS 40/84 as per RDSO Drg. No. T-10371 - 6 Nos. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

40.00 10372Alt2, T- 10368, T- 10371 Alt. 2, T-15083/88/Alt2 & T-11690/Alt2 and as per RDSO/SPN/168/2005 with latest amendments as applicable. Gauge tie plates (52 Kg/60Kg as per site requirement) Insulation for (BG) complete with insulating bush and washereach set comprising of: (a) Insulating plate for insulated tie plate BG as per RDSO Drg. No. T-10372-1 No. (b) Insulating bushing for insulated stretcher bar BG as per RDSO Drg. No. T10368 - 3 Nos. (c) Insulating Washer for insulated stretcher bar BG to IRS 40/84 as per RDSO drg. No. T-10371 - 6 Nos. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

20.00 Machine for ordinary turnout with tongue attachment insulation and other insulation as per RDSO Drg. S/3361@47>47@63 (for IRS type point machine) or RDSO Drg No.SA-9151/52 (for Siemens point machine) with latest amendments. However, the ground connection shall be procured only after confirmation from Railway engineer as per site condition /type of machine/turnout. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

5.00 Machine for derail switch with tongue attachment insulation as per RDSO Drg. S/3361@47>47?40@for IRS type point machine) or RDSO Drg No. SA 9151/52 (for Siemens point machine) with latest amendments. However the ground connection shall be procured only after Confirmation from Railway engineer as per latest site condition /type of machine/turnout. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

5.00 (Non interlocked working) after removing the existing fitting if any, adjustment, if necessary, cable termination, wiring, testing and commissioning of electrically operated point, fixing and connecting point indicator on derail switch if necessary. The work shall be done as per extant practice on NWR & the instruction of Railway Engineer at site. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution. NWR-PROJ-JP-S AND T/NORTH WESTERN RLY

of William RDSO/SPN/168/2005 with insulating bush and washer to suit point layout and conforming to RDSO Drg.No.T-10372 or latest, T-10368 or latest and T-10371 or latest. 1.1 Insulation for Leading stretcher bars(BG) each set comprising of: (a) Insulating plate for leading insulated stretcher bars BG as per RDSO Drg.No.T-10384 - 2 Nos. (b) Insulating bushing for leading insulated stretcher bars for BG as per RDSO Drg.No.T-10535- 4 Nos. (c) Insulating Washer for insulated stretcher bar BG as per RDSO drg.No.T-10371 - 6 Nos. 1.2 Insulation for following stretcher bars BG. Each set comprising of: (a) Insulating side plate for insulated stretcher bars BG as per RDSO Drg.No.T-10367 - 3 No. (b) Insulating bushing for insulated stretcher bars BG as per RDSO Drg.No..T- 10368 - 6 Nos. (c)Insulating washer for insulated stretcher bars BG as per RDSO Drg.No.T10371 - 12 Nos Inspection: (i) RITES if value of item in work more than 10 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

5.00 Electric Point Machine (IRS Type) and as per IRS:S 37/2022 Ver 2.0 or latest. Inspection: RDSO Inspection charges: Borne by Railways Payment terms: 100% after Supply.

5.00 Supply of motor is not included in this item. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after execution. Total 5407421.90 Item- 7 Track Circuit Equipments, HASSDAC, MSDAC, Block Instruments etc. S No. Item No Description of Item Unit Qty Rate Amount

100.00 Ver.1.0 or latest. Charging Capacity Rating 10 Amps for Charging 80 AH Battery. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after Supply

100.00 Drg. No.SA-20161-66/M or latest. Inspection: RDSO Inspection Charges: None Payment Terms: 100% after Supply.

100.00 resistance, track relay, battery, B type choke etc., in the Apparatus Case and Circuit battery box as per standard practice. Termination of tail cable on M 6 / Screw less terminals WAGO or FINOLEX or similar approved make terminals/ fuse blocks / HRC fuse. Item includes testing /commissioning of track circuit. Complete wiring material will be supplied by contractor. (Supply of Track feed battery charger, track feed battery, resistances & 'B' type choke & Track relays, ARA terminal/Modular terminals Wago/phoenix contact type will be supplied by Railways / covered in Schedule separately). Inspection: Consignee Inspection Charges: None Payment Terms: 100% after execution.

100.00 points zones also. The item includes provision of doubled continuity GI wire Circuit bonds on rail joints after drilling bond-hole of 7.0/7.2 mm Dia, skimming of fish plate, insertion of insulated block joint( if required), fixing of TLJB (separate for positive & negative rails) with angle iron for track feed/jumper/track relay ends of track circuits and also for fixing jumper cables as per approved Track Circuit Plan, making rail connections through suitable insulated sleeves from TLJB at TF, jumper & TR end with GI wire, rail clips for fixing bond wire on the TLJB as per standard practice, termination of tail cables on TLJB terminals etc. TF/TR wiring shall be fixed on the suitable arrangement on PRC sleepers with the help of Hooks. In case Engineer at site desires that jumpering from TLJBs is to be done using signalling cable 2 core X 2.5 sq. mm, contractor shall provide the jumpering cable using 2 X 2.5 sq. mm signalling cable. The signalling cable will be supplied by Railways. Hooks shall be provided on PRC sleepers with the help of suitable steel bracket. This item also includes fixing & supply of channel pins, Hooks etc. The item does not include includes supply of TLJB as per RDSO Drg. No. RST-11509 or latest as per technical specs Installation of Track Lead Junction Box (TLJB) as per Drg.No.RST-11509 or latest made from FRP material including brass bolts and hylam board sheet with terminals etc. (a) Installation and commissioning of TLJB complete with cover to be in black/red having approximate weight of 4.0 Kg with L-262mm W-212mm and H 90 mm and all the holes required for mounting on FRP stump (vertical two for each FRP angle) HDPE pipe, cable etc. (b) Installation and commissioning of Each TLJB having two Bakelite terminal block fitted horizontally: each Bakelite terminal block shall have two nickel chrome plate M10 brass terminal, 50mm long. Along with each TLJB, nickel chrome plated brass links (two nos.0f adequate strength for vertical linking of the terminals to be wired and fixed properly. (c) Installation of HDPE pipe of size 32/35mm, 380 mm long along with two nuts for fixing on the TLJB hole. (d) Installation of the FRP stump for mounting the TLJB to be made of one-meter long 30mm X30mmX 4mm angle (2 nos.) and 300mm long 30mm X30mmX 4mm angle (1 no.) fixed at 50 mm from the bottom using galvanised nuts and bolts. The TLJB and the angles for stump should be fixed in given holes on them for fixing using galvanised nuts and bolts. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after execution. NWR-PROJ-JP-S AND T/NORTH WESTERN RLY

300.00 made from FRP material including brass bolts and hylam board sheet with terminals etc. The technical specifications are as follows: (a) TLJB complete with cover to be in black/red having approximate weight of 4.0 Kg with L- 262mm W-212mm and H 90 mm and all the holes required for mounting on FRP stump (vertical two for each FRP angle) HDPE pipe, cable etc. (b) Each TLJB shall have two Bakelite terminal block fitted horizontally: each Bakelite terminal block shall have two nickel chrome plate M10 brass terminal, 50mm long. Along with each TLJB, nickel chrome plated brass links (two nos.0f adequate strength for vertical linking of the terminals to be supplied. (c) HDPE pipe of size 32/35mm, 380 mm long alongwith two nuts for fixing on the TLJB hole. (d) The FRP stump for mounting the TLJB to be made of one-meter long 30mm X30mmX 4mm angle (2 nos.) and 300mm long 30mm X30mmX 4mm angle (1 no.) fixed at 50 mm from the bottom using galvanised nuts and bolts. The TLJB and the angles for stump should come alongwith holes on them for fixing using galvanised nuts and bolts of adequate strength to be supplied alongwith TLJB drawing no. 11509. Inspection: (i) RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

300.00 supports (FRP stumps) with contractor's fixing material. This will include drilling of holes for track lead/side connections on rail. The work shall be done as per instructions of Rly engineer at site. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after execution.

200.00 latest. Inspection: RDSO Inspection Charges: Borne by Railways. Payment Terms: 100% after supply.

1000.00 4mm Dia bonding wire as per spec No IRS S 17 & RDSO Drg No. S-69/M. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply.

100.00 Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply.

500.00 jumper & fish plate joints bonds. This will include drilling of 7.0/7.1/7.2 mm Dia holes in rails (4 Nos.) and provision of two jumpers for each bond, clipping of bonds etc. with contractors own tools as per instruction of Rly. Engineer at site. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Execution.

25.00 Battery Graded acid with mounting stand in location Boxes. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply.

100.00 Testing and Commissioning of Multi Section Digital Axle Counter (MSDAC) Detection complete system as per RDSO Specification No. RDSO/SPN/176/2013 Point (DP) version.3 with latest amendments STR No. SIQ 0001 Ver.2.0 or latest. MSDAC Reset procedure shall be as per NWR MSDAC Reset policy. Tenderer shall design the scheme for provision of required number of evaluators, reset equipment's, trackside junction boxes, detection points and track clearance relays etc and shall be submitted along with the offer. Remote Diagnostic System shall be provided at station. Length of the cable required for each DP and Rail Type will be specified at the time of issuing call Letter. [This also includes supply of 10% all types of spare cards, LV Boxes, Wheel sensors and other essential modules as specified in RDSO Spec, it shall be rounded to nearest integer subjected minimum of one item. One set of Specialized Tool and Measuring equipment's as per RDSO specifications shall be supplied per location (Station/ALH/OC/IBH). (Per Detection Point = DP). Note: It also includes supply and Installation of any earthing arrangement, if required as per OEM specification. Inspection: (i) RDSO - for supply items. (ii) Consignee - for other execution. Inspection Charges: Borne by Railways. Payment Terms: 80% after Supply, 20% after execution & commissioning.

1.00 1486809.00 for Single line operation as per RDSO Spec. No. IRS:S 105-2025 ver.1.0 or latest (Per Unit=Set Per Block Section) Inspection: RDSO Inspection Charges: Borne by Railways. Payment Terms: 100% after Supply.

1.00 Single line/Double line operation as per RDSO Spec. N o . IRS:S 105-2025 ver.1.0 or latest. [All miscellaneous items required for commissioning shall be supplied by contractor] (Per Unit=Set Per Block Section) Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after commissioning.

6.00 1276272.00 (Digital) [SSBPAC(D)] complete for Single line operation as per RDSO Spec. No. RDSO/SPN/175/2005Ver.1 or latest including Station Master's Block Panel, Wired Relay Racks with Relays, necessary Lightening & Surge Protection Devices for Power Lines 24V DC & Data Lines and Block Telephone as per RDSO/SPN/191/2005 or latest (Per Unit = Set Per Block Section). Inspection: RDSO Inspection Charges: Borne by Railways. Payment Terms: 100% after Supply.

6.00 Station Master's Block panel and Automatic Media Changeover Card for Single line operation as per RDSO Spec. No. RDSO/SPN/175/2005 Ver.1 or latest. [All miscellaneous items required f o r commissioning s h a l l b e supplied by contractor] (Per Unit = Set Per Block Section) Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after commissioning.

3.00 114415.00 One Voice Modem Circuit and O n e E 1 Converter Circuit, for working on redundant channels for data transmission on OFC/ Quad. Necessary Lightning & Surge protection devices for data lines need to be provided. Inspection: RDSO Inspection Charges: Borne by Railways. Payment Terms: 100% after Supply. Total 53341156.75 NWR-PROJ-JP-S AND T/NORTH WESTERN RLY Item- 8 LED Main & Subsidiary signals, CLS units, Route Indicators & foundation etc. S No. Item No Description of Item Unit Qty Rate Amount

419.00 signals/main signals (i.e. route, shunt, calling on, Red, Yellow, Green) as per instructions given by engineer incharge. Complete wiring inside the signal unit with 2.5 sq. mm multi strand wire of different colour according to signal aspect with copper lug as per standard practice. The contractor will supply all materials required for installation. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution.

60.00 mm Dia, as per IRS: S-6/81 or Latest & RDSO Drg. No. SA-24625 (Advance). (2) CI Base (As per IRS S-10 & RDSO Drg. No. 2011/M with latest assembly). (3) Number plate to Drawing No. S 23149 Alt.1 =1 No, Number plate clamps to Drawing No. S 23148 Alt.1 =2 no (4) Ladder Assembly, as per RDSO Drg. No. SA-23156, with Base, Ladder Guard rail (complete) to Drawing No. SA 23138 Alt.1(1No), Platform to Drawing No. SA 23134 Alt.1(1 No), Front Maintenance Platform, MS Supporting bracket to Support Ladder. Ladder stay (small) to Drawing No. S 23159 Alt. 1 (2 Nos.) , Ladder stay (large) to Drawing No. S 23160 Alt. 1 (2 Nos.) , Ladder section to Drawing No. SA 23157 Alt. 1(1 Nos.)Stay clamp to Drawing No. SA 2062/M (2 no), Rail Clamp to Drawing No. S 2066/M (1 No.) (5) Signal Front Staging Complete Assembly for CLS Unit. (6) Signal back staging as per extent NWR Practice. Note: Height of the Post shall be 5.5 Long. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee- if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

6.00 diameter 140 mm, thickness of pipe 4.5 mm. horizontal length of pipe 545 mm & vertical length of pipe 324 mm with fixing arrangement on Main Signal post as per Drawing No SW/554/G/R. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee- if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

30.00 diameter 89 mm, thickness of pipe 4.5 mm. horizontal length of pipe 324 mm & vertical length of pipe 324 mm with fixing arrangement on Shunt Signal post as per Drawing No SW/354/I. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee- if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply Erection of CLS Post with base and signal unit on top or on OFFset Bracket, fixing of front and back staging, ladder and guards, signal name plates / boards if any with contractor's own brackets and fixing materials. This also includes erection of auxiliary signals like calling on, shunt signal if any. The work shall be done as per instructions of Rly engineer at site. It also includes provision & fixing of maintenance platform as per design given by Engineer - In-Charge at site. The Item includes cutting of Signal post if required by Site In charge. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation.

15.00 indicator 1/2/3/4/5/6 or multi-lamp lamp route indicators/Stencil type rout indicator mounted on signal post.

25.00 railway signalling suitable for RE area TWO Aspects. Complete without lenses, lamps and signal transformer as per RDSO DRG. No. SA 23001/A/M Adv. Alt- S and as per SPEC. No. RDSO/SPN/194/2006 (Rev 2.0) or latest and FRP material as per RDSO SPEC. No. RDSO/SPN/151/1997 or latest. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee- if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

20.00 railway signalling suitable for RE area THREE Aspects. Complete without lenses, lamps and signal transformer as per RDSO DRG. No. SA 23001/A/M Adv. Alt- S and as per SPEC. No. RDSO/SPN/194/2006 (Rev 2.0) or latest and FRP material as per RDSO SPEC. No. RDSO/SPN/151/1997 or latest. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee- if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

2.00 railway signalling suitable for RE area FOUR Aspects. Complete without lenses, lamps and signal transformer as per RDSO DRG. No. SA 23001/A/M Adv. Alt- S and as per SPEC. No. RDSO/SPN/194/2006 (Rev 2.0) or latest and FRP material as per RDSO SPEC. No. RDSO/SPN/151/1997 or latest. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee- if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

20.00 of 80 mm Diameter Medium Class IS Spec. No. IS: 1239 Pt. 1/1990, Base, Hood, Cover etc as per Drg. No. SA-23840 suitable for LED Signal Lighting Unit. (Supply of LED Unit is not covered in this item) Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee- if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

20.00 Number Plates. The work shall be done as per instructions of Rly engineer at site. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation. NWR-PROJ-JP-S AND T/NORTH WESTERN RLY

30.00 Cover etc as per Drg. No. SA-23840 suitable for LED Signal Lighting Unit. (Supply of LED Unit is not covered in this item) Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee- if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

30.00 Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation.

15.00 per Drg. No. RDSO SA 23403 suitable for LED Signal Lighting Unit & as IRS:S- 66/84 amndt-1 or latest.(Supply of LED Unit is not covered in this item) Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee- if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i) Borne by Railways (ii) None Payment Terms: 100% on Supply

6.00 white LED along with housing as per specification. For 1 to 19 (double digit) MLRI, two digits LED route indicator capable of displaying 1 to 19 routes and route 'G'. Visibility of 300 metres in clear day light. Option for white, chromaticity as per BS:1376 standard. Built with robust AlinGap, InGan LEDs junction temperature more than 100% BOC. Lamp proving compatible with normal bulb type multi lamp route indicators. Retrofits the existing conventional multi lamp type route indicators housing. Input operating voltage 110V AC +25%. Uniform intensity over entire operating range. Operating temperature - 10%B0 C to + 60%B0 C. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee- if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i) Borne by Railways (ii) None Payment Terms: 100% on Supply

15.00 Way on the top of the signal post. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation.

6.00 Signal Unit shall conform to RDSO Drg no 24351(Adv) Alt1 suitable to LED Signal Lighting Unit. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee- if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i) Borne by Railways (ii) None Payment Terms: 100% on Supply

15.00 includes fixing of Co- On signal /'A' sign/ 'AG' sign unit on signal post with bracket, hood etc. Item includes supply of bracket & fixing materials etc. by the contactor. The item also includes termination of cables & wiring inside Co- On signal /'A' sign/ 'AG' sign unit as per standard practice. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation.

5.00 Board/Shunting Limit Board as per RDSO Drg. No. SA2375 (Adv.). This includes Painting and retro reflective arrangement should be as per SEM. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation.

12.00 Signalling system as per latest specification. This includes Painting and retro reflective arrangement should be as per IRSEM. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation.

10.00 warning board, Calling on Board with contractors own material. This excludes supply of Stop Board / Block section limit Board / Goods warning board/Calling on board. The work shall be done as per instruction of Rly Engineer at site. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation.

15.00 'P' Marker, Arrow Marker, 'G' Marker, 'C' Marker as per IRSEM drawings. All material required for this work shall be supplied by Contractor. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation.

10.00 1200 x 1500 mm on signals as per std. practice in RE Area. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation.

47.00 CSTE/NWR/SOR/21/A using standard size of foundation/galvanized holding down bolts required for erection of colour light signal post. Item includes excavation, ramming of CC using vibrator, curing and plastering with 1:4 cement-sand mixture (aggregate will not exceed 3.8 cm). Aggregate, cement, sand and holding down bolts will be supplied by contractor. Any machines & tools, if required for execution of this item, will be arranged/provided by contractor. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation.

20.00 Drg. No. CSTE/NWR/SOR/22 in ratio 1:3:6 by using standard size of galvanized holding down/foundation bolts. Item includes excavation, ramming of CC using vibrator, curing and plastering with 1:4 cement sand mixture. Aggregate cement, sand and holding down bolts, will be supplied by contractor. Any machines and tools, if required for execution of this item, will be arranged/provided by contractor. Note: As per available site conditions, if sizes of foundations are required to be decreased/ increased and same has been approved/agreed by engineer incharge then variation in CC work will be calculated on volumetric basis as per rates of these items. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation. Total 4969907.20 Item- 9 Level Crossing Gates, Interlocking of LC gates, ELBs, Accessories etc. S No. Item No Description of Item Unit Qty Rate Amount NWR-PROJ-JP-S AND T/NORTH WESTERN RLY

3.00 521717.26 110VDC/24V DC (option to be specified in tender specifically of either 110 V DC or 24V DC) supply without hand generator back up & motorized boom locking arrangements as per RDSO Spec. SPN/208/2012, Ver 2.0 with latest amendment. One set consisting 02 Nos of Barriers of length 09.76 Mtrs. along with Spares & tool kit mentioned in RDSO Spec. SPN/208/2012 clause 10.1 & 10.2 as below 10.1 Following spares shall be supplied alongwith each set (02 nos.) of Electric lifting barrier as per requirement of the purchaser i) GI boom - 1 no. complete. ii) Belt - 1 no. iii) Crank handle - 1 no. iv) Motor Contactor - 1 no. v) Motor protection MCB- 1 no. vi) Push button complete- 2 nos. vii) Limit switch - 3 nos. (1 lever type and 2 top roller type) viii) Fuses used - 2 sets 10.2 Tool kit consisting of standard sizes of wrench/ spanner and Allen keys should also be supplied with each set (02 nos.) of Electric Lifting barrier. Inspection: RDSO Inspection Charges: Borne by Railways. Payment Terms: 100% after Supply.

3.00 complete with Casting of cement concrete foundation for pedestal and boom rest post, cabling, power supply connection & wiring with complete outdoor work as per approved drawing, wiring etc. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Commissioning

50.00 sheets of size 305 x 290 mm one set consist 18 pieces. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% on Supply

8.00 working on 24 V DC/ 110 V AC for warning road users at LC gates. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply

2.00 includes wiring of KLCR, running of cables, necessary painting & transportation of materials from store to site. All material required to commissioning of slide booms on gate will be supplied by the contactor. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Commissioning

1.00 Minimum 10 Nos of foundation per set shall be cast using standard size holding down bolts & nuts for erection. Item include excavation, ramming, curing and plastering 1:4 cement and sand mixture. Aggregate, cement, sand and holding down bolts & nuts to be supplied by the contactor. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after installation

1.00 as per technical specification and site requirement. The indoor wiring inside panel shall be terminated on tag block as per instructions of Engineer-in- charge. The wiring on panel tag blocks shall be repeated on tag blocks located in relay room. This includes laying & termination of cable, if any from Panel Room to Relay Room in HDPE pipe. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation

3.00 illuminated diagram board, block counter, termination box, telephones, emergency key box, dismantling of ground lever frame along with all connected lever locks, 'E' type locks, HP locks, breaking and removal of concrete foundation, lock rods with rod roller trestles, complete assembly, cranks, compensators, 'A' type concrete foundation on the rod run, transmission wires single wire/double wire accounting and stocking them neatly at a place as instructed by Railway representative at site. After releasing any holes on the walls/ floor are to be filled with cement mortar and plastered. Total 1999264.95 Item- 10 Panel room Equipments, VDUs (Video Display Units), Fire alarm Equipments, Furniture S No. Item No Description of Item Unit Qty Rate Amount

10.00 Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply.

2.00 of reputed brand. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply.

2.00 and one locker on the righthand side. Olive brown with duplicate keys. Make: Godrej Model T-9 (136.5 cmX68cmX 75cm)or Superior of reputed brand. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply.

2.00 915 mm width and 485 mm depth. Make: Godrej Storewel Plain Large or Similar of reputed brand. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply.

60.00 sensor as per RDSO/SPN/217/2025 ver-3.1 or latest. along with its base, back- box and all accessories incompliance with IS:2175 and IS:11360 standard sand Under writers Laboratory (UL) listed. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after execution.

4.00 RDSO/SPN/217/2025 ver-3.1 or latest with backbox and all other accessories Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after execution.

300.00 RDSO/SPN/217/2025 ver-3.1 or latest Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after Supply.

400.00 RDSO/SPN/217/2025 ver-3.1 or latest Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after Supply. NWR-PROJ-JP-S AND T/NORTH WESTERN RLY

4.00 210156.00 addressable Fire alarm Control panel expandable up to 4 loops with GSM interface as per RDSO/SPN/217/2025 ver-3.1 or latest. This work involves supply, fixing, installation and testing of control panel. The control panel shall be networkable to Zonal /Divisional headquarters preferably over TCP/lP and shall hav e clock synchronization facility. This includes Networking module (TCP/IP) for control panel along with power supply unit and battery set of required capacity for 24 hours backup as per RDSO specification. The panel should support degrade mode operation in compliance with IS: 2189, EN54 standards a n d Underwriters Laboratory (UL) listed. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after execution.

4.00 (resettable) with backbox and all other accessories as per RDSO/SPN/217/2025ver-3.1 or latest Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after execution.

20.00 fire extinguisher 6.5kg capacity conforming to IS15683 with ISI mark provided with all fittings and accessories. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after execution

4.00 630843.00 system for monitoring of rooms a n d equipment f o r earliest possible fire detection F o r Re l a y r o o m s a s p e r R D S O spec. No. RDSO/SPN/217/2025 ver3.1or latest. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after Supply

4.00 257648.00 accessories for the Aspiration System. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after execution

Testing Aspiration Smoke detection Supplied. Supply of FIRE SUPRESSION SYSTEM (FSS) as per RDSO/SPN/218/2016 Version 1.0- d2. Design, Supply and Installation of Fire Suppression system having non-toxic, environment friendly, noncorrosive, clean gaseous agent at the atmospheric pressure, safe for Electronic/ Electrical/ Telecommunication Equipments/ Computers, Human Friendly, non-residual, non-inflammable, type agent (C3F7H) (HFC 227ea) FM 200 GAS. This system must include Hydraulic Flow Calculations for the Suppression areas, and vetting of the Software Results from the OEM Factory Engineer. This shall be a Total Flooding system for Relay Room and Equipment Room with Automatic sensing and Activation along with the microprocessor based Advance Multifunction Programmable Control Panel as detailed in the annexure. The system includes following subsystems:

6.00 107567.00 Version 1.0-d2, fitted with valve assembly and along with mounting straps suitable to operate at 25 bar Pressure complete with safety burst disc, safety cap and with UL/FM/LPCB listed CCOE approval. In case of other capacity cylinder, cylinder bank design should maintain 25 Bar pressure and require clean agent quantity as per design. Cylinder "litres' capacity should be same for across all locations in all the banks. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after Supply.

792.00 agent at the atmospheric pressure, safe for Electronic/ Electrical/ Telecommunication Equipments/ Computers. Human Friendly. non-residual. non- inflammable type agent Heptafluoropropane (C3F7H) (HFC 227ea) FM 200 GAS LPCB/FM/UL approved. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after Supply.

4.00 complying to RDSO/SPN/218/2016 Version 1.0- d2. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after Supply.

4.00 Actuator complying to RDSO/SPN/ 218/ 2016 Version 1.0- d2. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after execution

3.00 Actuation Hose Assembly complying to RDSO/SPN/218/2016 Version 1.0- d2. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after execution

2.00 Actuation Assembly complying to RDSO/SPN/218/2016 Version 1.0- d2. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after execution

1.00 Assembly complying to RDSO/SPN/218/2016 Version 1.0- d2. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after execution

6.00 pressure Discharge hose complete with Listed Adapters & Accessories as required. As per RDSO Specification No. RDSO/SPN/217/2016 Ver. 1.0. d1. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after execution

3.00 RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after execution

18.00 360 Deg / 180 Deg Throw, selection as per approved hydraulic flow calculations complying to RDSO/SPN/218/2016 Version 1.0- d2. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after Supply

4.00 Release Unit Stations with DPDT Relay, it shall be fitted with transparent hinged covers to avoid the possibility of accidental operation. The Release switch will be monitored simultaneously by Fire Alarm and Remote Monitoring Software complying to RDSO/SPN/218/2016 Version 1.0- d2. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after execution NWR-PROJ-JP-S AND T/NORTH WESTERN RLY

4.00 Gas Abort Unit Stations with DPDT Relay, shall be fitted with transparent hinged covers to avoid the possibility of accidental operation. The Abort will be monitored simultaneously by Fire Alarm and Remote Monitoring software complying to DSO/SPN/218/2016 Version 1.0- d2. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after execution

4.00 Proximity Sensor. It shall have Warning Sign Board with Parking "GAS DISCHARGE. DO NOT ENTER". Shall Operate on 24 V OC, Driven Through Gas Release Panel. (for use outside room) Complying to RDSO/SPN/218/2016 Version 1.0- d2. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after execution

6.00 coats of primer and 2 coats of Red Enamel Paint as per the design requirements. It shall be as per flow calculations for the specific hazard volume and stand to hold, position & Support the Manifold and Piping properly. Pressure testing for piping shall be with nitrogen as per NFPA 2001. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after Supply.

4.00 Pressure Switch. Complying to RDSO/SPN/218/2016 Version 1.0- d2. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after execution

6.00 switch to monitor the health of cylinder. Complying to RDSO/SPN/218/2016 Version 1.0- d2. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after execution Total 10220248.96 Item- 11 Apparatus case, outdoor installation, Fuses, ARA Terminal, Hylam Sheet, Phenolic Laminated sheets S No. Item No Description of Item Unit Qty Rate Amount

100.00 CSTE/6088 fitted with two nos of E Type lock (ward No will be specified by Engineer-in Charge) as per RDSO Drg. No. SA 3376 and Key to Drg. No. 3377 as per RDSO drawing No. RDSO/S-11500. Note: This item includes the supply of 2 Nos E Type Lock fitted on both doors, along with two Keys. Inspection: (i) RITES if value of item in work more than 10 lakhs or as per extant instructions by Railway Board. (ii) Consignee if value of whole item in work less than 10 lakhs or as per extant instructions by Railway Board. Inspection Charges:(i) Borne by Railways (ii) None Payment Terms: 100% after Supply.

100.00 foundation. This includes filling of location foundations with river bed sand and plastering on top of the sand. Supply of 'E' Type lock has been covered in supply of Apparatus case separately. It covers fixing of lamp holder, switch and lamp etc. in Apparatus Case. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after installation.

50.00 CSTE/6088 fitted with two nos of E Type lock (ward No will be specified by Engineer-in Charge) as per RDSO Drg. No. SA 3376 and Key to Drg. No. 3377 as per RDSO drawing No. RDSO/S-11507. Note: This item includes the supply of 2 Nos E Type Lock fitted on both doors, along with two Keys. Inspection: (i) RITES if value of item in work more than 10 lakhs or as per extant instructions by Railway Board. (ii) Consignee if value of whole item in work less than 10 lakhs or as per extant instructions by Railway Board. Inspection Charges:(i) Borne by Railways (ii) None Payment Terms: 100% after Supply.

50.00 foundation. This includes filling of location foundations with river bed sand and plastering on top of the sand. Supply of 'E' Type lock has been covered in supply of Apparatus case separately. It covers fixing of Location lamp holder, switch and lamp etc. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after installation. Excavation and Casting of Apparatus Case foundation in ratio 1:3:6 with contractor's own materials including cement and galvanized anchor bolts of standard size. The required scaffolding Ferma etc for Casting of foundation will have to be brought by the contractor at his own cost. The item also includes additional masonry work as well as earthwork if required on bank where there will be possibilities of foundation sinked, fallen or tilted. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after installation.

100.00 Signalling Installations for protection from outside interference. The work involves erecting posts using GI pipes 25mm Dia -3m long near the locationaround boxes at an interval of 2m and providing fencing using barbed steel wires the location boxes. The GI pipes shall be buried to a depth of 1m. The barbed wire shall be providing using 14 SWG GI wire (2 wires) barbed at 6" interval. The wires shall be provided from ground level to the top of post at an interval of 6", The work also includes erection of two rail posts, fabrication of a gate using MS angles 50x50x5mm and MS flats 50mmx3mm and fixing it on the rails and provision of locking facility as per the instructions of Railway representative at site. (Rails of different lengths will be supplied by Railways. The Contractor has to cut the rails to the required lengths as per the requirement). GI pipes 25mm thick, barbed steel wire, MS angles 50mmx50mmx5mm and MS flats 50mmx5mm for work fabrication of gate, and all other miscellaneous materials required for the shall be supplied by the Contractor. The gate width shall be 1.25 to 1.5m as per site conditions and instructions from consignee. Reference drawing for execution of this item is attached in Tender document. (Unit = Sqm =Sqm on Ground area) Inspection: Consignee Inspection Charges: None Payment: 100% after execution NWR-PROJ-JP-S AND T/NORTH WESTERN RLY

70.00 x 20 mm as per spec. No IS 2036 of 1995 or latest. Test report of manufacture to be supplied. Inspection: (i) RITES if value of item in work more than 10 lakhs or as per extant instructions by Railway Board. (ii) Consignee Inspection Charges:(i) Borne by Railways(ii) None Payment Terms: 100% after Supply.

50.00 x 12 mm as per spec. No IS 2036 of 1995 or latest. Test report of manufacture to be supplied. Inspection: (i) RITES if value of item in work more than 10 lakhs or as per extant instructions by Railway Board. (ii) Consignee Inspection Charges:(i) Borne by Railways (ii) None Payment Terms: 100% after Supply. Fabrication and fixing of phenolic laminated sheet of size 10/12/20 mm thick in location box by providing all fixtures as per Railway Drawing including fixing of PVC coated string rods at the back side for cable support with contractor's own materials. The work shall be done as per instructions of Rly engineer at site. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after installation.

15000.00 terminal blocks and fuse blocks on phenolic laminated sheets and fixing by stainless steel/brass nuts & bolts. This includes provision of two additional holes on the board on either side for cable conductor entry. (Supply of all above terminals have been covered separately in Chapter 4 of SOR) Inspection: Consignee Inspection Charges: None Payment Terms: 100% after installation.

150.00 reputed make) Inspection: Consignee Inspection Charges: None Payment Terms: 100% after supply

30.00 3473, 3373 & spec. IRS(S) 30/64. Ward to be specified by Engineer - in - charge. Inspection: Consignee. Inspection Charges: None. Payment Terms: 100% after supply.

20.00 provided or at any other location as decided by engineer in charge. Item includes supply and fixing of MS sheet and wiring of KLCR relays, push buttons and LEDs for KLCR circuit. The KLCR relays, push buttons, LEDs will be fixed on a MS sheet of min. 3mm in the half location box. The MS sheet will cover full length and breadth of the half location box and divided in two pieces of approx. 48cm x 46cm and 80cm x 46cm. The first piece to be fitted on top and will contain the KLCR relays, LEDs and push buttons. The second piece to be fitted below the first piece. (Supply of KLCR relays covered in separate item of SOR). Inspection: Consignee Inspection Charges: None Payment Terms: 100% after installation. Total 5596644.00 Item- 12 Cable laying material, Cable protection, Cable execution, Jointing Kits items etc. S No. Item No Description of Item Unit Qty Rate Amount

250.00 1239 (Part 1): 2004 with coupling on culverts bridges as per Drg. No. CSTE/NWR/SOR/06 to 12 or at any other locations as decided by Site Engineer. It includes supply of all material required for fixing arrangement. Contractor will also supply flexible/corrugated HDPE pipe at the end of GI pipe to protect the cables from sharp edges and sudden bends. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

250.00 (Part 1): 2004 with coupling on culverts bridges as per Drg. No. CSTE/NWR/SOR/06 to 12 or at any other locations as decided by Site Engineer. It includes installation of all material required for fixing arrangement. Contractor will install flexible/corrugated HDPE pipe at the end of GI pipe along with any masonry work (if required) to protect the cables from sharp edges and sudden bends. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation.

180.00 1239 (Part 1): 2004 for use in ASM room and at any other location as decided by Site Engineer. It includes supply of all material required for fixing arrangement. At the ends of GI pipe, flexible/corrugated HDPE pipe will be provided by contractor to protect cables from sharp edges and sudden bends. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply

180.00 (Part 1): 2004 for use in ASM room and at any other location as decided by Site Engineer. It includes installation of all material required for fixing arrangement. At the ends of GI pipe, flexible/corrugated HDPE pipe along with any masonry work (if required) will be provided by contractor to protect cables from sharp edges and sudden bends. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Installation. Supplying and placing of one layer of standard size of 'B' grade quality bricks of the local make spreading on cables laid. (minimum size of brick 200mm X 100mm X 70mm) Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Installation.

Running Length wise (up to 2 cables). Metre

Running Width wise (more than 2 cables) Metre NWR-PROJ-JP-S AND T/NORTH WESTERN RLY

300.00 collars etc. as per RDSO Specification No. RDSO/SPN/204/2011 or latest anti- rodent & anti-oxidant and non-flame propagating type in 6 meters straight length and of size 120 mm outer Dia & 103.5 mm inner dia. (The manufacturers, suppliers must produce valid IS license and should be certified under ISO 9000 and shall submit copy of certificate). One of the following coupling arrangements should also be supplied with each pipe as per the site requirement.1) Suitable snap fit coupler with rubber O-Ring 2) Spacers3) Tees4) Bend,5) End-cap(The total quantity of above items is equal to no. of pipes supplied.)DWC pipe shall be marked at every 1 mtr length in such a way that manufacturer's name, vendor name and year of manufacture can be easily identified. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs or as per extant policy (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs or as per extant policy Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% after Supply

200.00 collars etc. as per RDSO Specification No. RDSO/SPN/204/2011 or latest anti- rodent & anti-oxidant and non-flame propagating type in 6 meters straight length and of size 50 mm outer Dia, & 38 mm inner dia. (The manufacturers, suppliers must produce valid IS license and should be certified under ISO 9000 and shall submit copy of certificate). One of the following coupling arrangements should also be supplied with each pipe as per the site requirement.1) Suitable snap fit coupler with rubber 'O-Ring 2) Spacers3) Tees4) Bend,5) End-cap(The total quantity of above items is equal to no. of pipes supplied.)DWC pipe shall be marked at every 1 mtr length in such a way that manufacturer's name, vender name and year of manufacture can be easily identified. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs or as per extant policy (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs or as per extant policy Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% after Supply

1000.00 outer Dia, & 175 mm inner dia. It includes supply of Double Wall Corrugated - HDPE pipe/duct as per RDSO Spec. No. RDSO/SPN/ 204/2011 (version 1.1) or latest and conforming to ISI Spec. No.IS:14930, Part-II. (The manufacturers, suppliers must produce valid IS license and should be certified under ISO 9000 and shall submit copy of certificate). One of the following coupling arrangements should also be supplied with each pipe as per the site requirement.1) Suitable snap fit coupler with rubber O-Ring 2) Spacers3) Tees4) Bend,5) End-capDWC pipe shall be marked at every 1 mtr length in such a way that manufacturer's name, vendor name and year of manufacture can be easily identified. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs or as per extant policy (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 10 lakhs or as per extant policy Inspection Charges: (i)Borne by Railways(ii) None Payment Terms: 100% after Supply

500.00 as per IS No. 458/2003 of NP type. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply

4000.00 near track and road, crossings, platform cuttings etc. Inspection: Consignee Metre Inspection Charges: None. Payment Terms: 100% after Execution

9000.00 240mm/340mm, height 155mm/230mm, internal/external length 1 Mtr produced of polyolefin with fire protection class K-1 in accordance with DIN- 53438 part II for laying of Signalling/Telecom cables, channel attachable to each other with male female swallow tail connectors and having suitable detachable cover, as per technical specification RDSO letter-Ref No. STS/Cable-Laying practices Vol-IV dated 09/05/2018. Inspection: RITES/RDSO Inspection Charges: Will be borne by Railways. Payment Terms: 100% after execution

20.00 joints) as per RDSO spec IRS/TC-77/2012 revision 3 With latest Amd. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after Supply

10.00 Jointing Kit. All the material required for the work are to be arranged by contractor himself at his own cost except Thermo shrinkable Joint Kit/Rapid Joint kit. After jointing the cable through test such as insulation test, continuity cable losses etc. to be carried out jointly with Railway Engineer. If any defect or any damage is observed during jointing, the contactor has to redo the joint free of cost. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution

1200.00 using Auger Machine (HDD machine) or by Closed trench Method. The bore shall be upto 200 mm Dia & shall be done at the depth of minimum 1200 mm from the ground level. The ground level shall be considered ignoring the bank height of the bank of the road. The length of the bore shall be minimum 4 Mtrs long. This includes insertion of different Dia DWC-HDPE pipe/ GI pipes coupling etc. as per direction of Engineer In charge. Note: - Pipe Supply is not covered under this item. Contactor shall provide all material required for boring and adequate nos. of labours for proper laying of cables into the bore. Cable shall be laid cautiously so that it should not get damage due to rough handling & pressure on cable. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution

40.00 the route at every 50 meter and route diversion as per Drg. No 4014/00/CC4 or latest/ Stone marker. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply

40.00 and painted on both side along the route at every 50 meter and route diversion as per Drg. No 4014/00/CC4 or latest/ Stone marker. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution NWR-PROJ-JP-S AND T/NORTH WESTERN RLY

25.00 Location box. The work includes breaking/ Dismantling of Existing foundation of locations, excavating and removing / segregating coils of 2C/6C/12C/19C/24C/30C/Quad cables which may be about 10 mtrs. in length. These cables are to be disconnected and removed from the existing location one by one as per the instruction and under the supervision of Railway staff present at site. The cable is then to be inserted and terminated in new location box. The item includes neatly dressing of cable, making wiring tree etc. The material required to dressing /lacing will be arranged by contactor. The work is required to be done systematically and with due precaution during the block or disconnection within the time that may be allowed. The excavation work to be done carefully without damaging the cable to avoid undue failure. (Termination charges will be given separately). Note: Proportionate payment will be made if cable of other length. One No unit = One cable of 10 m length) Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Execution

2.00 existing trench & laying the same in new trenches. Digging, placing of capping/Half round RCC pipe covered separately. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution

3000.00 Mtr. to 0.6 Mtr. wide at bottom as per RDSO sketch No. SDO/CABLE LAYING/003 or latest alongside the track in normal (all type) soil/strata, conforming to distances as per cable route plan and refilling. This work includes clearing of route from bushes etc, covering of cable laid in trench by loose soil for a layer of 50mm thickness approximately before covering by bricks. The work shall be done as per the extant practice on North Western Railway and instructions of Railway Engineer at site. In case 1.2m depth of trench is not achievable due to site conditions, specific approval of JA grade officer will be required for each site where trench depth of 1.2m is not possible. Without the approval of JA Grade officer, no payment for trenching will be made for trench depth less than 1.2m. (cum is Cubic Meter) Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution

50.00 0.6 Mtrs wide and back filling after placing of DWC/ RCC/GI pipe. (Placing of DWC/RCC/GI pipe covered separately). The ballast disturbed be screened and dressed as required by Engineer-in-charge or his representatives and road tarred immediately. For track crossing, Drg. No. CSTE/3644 Pg.7 of 11 and for Road Crossing, Drg. No. CSTE/3644 Pg. 5 of 11 are to be followed. (cum is Cubic Meter) Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution

50.00 Platform / Road / Hard rocky area. Refilling with earth levelling of trenches & restoring the original surface of trenches. The sharp edges will be smoothened out in bottom of the chase and will be levelled properly. In hard rocky ground area, cables will be laid normally on layer of shifted earth of 0.05 mtrs thickness previously deposited at bottom of the trench and cables will be covered with layer of sand or shifted earth of 0.1 mtr thickness. In case sharp edges of rocky ground cannot be protected from shifted earth then GI/ CI /PVC /DWC/ HDPE pipes will be used, if numbers of cables are small. In case number of cables are large RCC duct will be used. In isolated cases, it can be given smooth surface by using either masonry bricks or cement concrete. A row of bricks shall then be placed length wise on the top and jointed with cement mortar and layer of concrete with cement plaster shall be provided on top of the same. Note: This item in hard rocky area will be operated only where normal depth i.e.l.2 mtr is not possible and it will be decided by site engineer/unit officer incharge of work. (cum is Cubic Meter) Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution

3.00 supplying and filling of sand before and after coiling the cables, covering top of the cable pit with stones and providing brick masonry on all four sides of the cable pit and plastering thereafter. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Execution

430000.00 pipes/ DWC pipes/ Trunking. This also includes laying of cables in track Metre crossings & road crossings. Item includes provision of labels of coloured plastic adhesive tapes or any other identifiable material on each cable to give the cable number at each Gantry Post/hectometer post. (Cables will be meggered before and after its laying by contractor under supervision of Railway Representative and he will submit the meggering report of each testing). Length of the cable laid includes the length of the cable coiled for termination purposes. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution

10.00 includes excavation, ramming, curing and plastering with cement & sand mixture (aggregate not exceeding 3.8 cm.) (Aggregate cement & sand to be supplied by the contractor)(cum is Cubic Meter). Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution

10.00 with 1:4 cement and sand mixture both sides, 20 mm thick each with contractor's owned class II bricks, including excavation, curing, grouting, bolting etc. wherever required. Bricks sand and cement to be supplied by the contractor.(cum is Cubic Meter) Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution Total 33436249.62 Item- 13 Earthing, Measuring Instruments, Multi-meter, Earth Tester, Clamp meters, Fault Locators, ELD (Earth Leakage Detector) etc. S No. Item No Description of Item Unit Qty Rate Amount Supply of Earth Leakage Detector (ELD), LEVEL-3, as per RDSO Spec. RDSO/SPN/256/2025 or latest., with Earth Fault Localization system. The engineer-in-charge to specify the distribution of number of channels of DC or AC voltage on the bus bar/ conductor for which earth leakage detector is required. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after Supply

Numbers NWR-PROJ-JP-S AND T/NORTH WESTERN RLY

4.00 (ELD), 12/16 Channels as per RDSO Spec. RDSO/SPN/256/2025 or latest. This includes supply of fuse terminal strip for incoming power supply wires. On job training at site will be given by OEM engineer for installation and maintenance of ELD. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after commissioning.

20.00 RDSO Specs. No. RDSO/SPN/197 Version 1.0 dtd. 04.07.2016 or latest and conforming to RDSO Drg. No. SDO/ RDSO/E&B/001. It consist of following: (a) Copper bonded steel electrode of 3.0 m long, 17 mm Dia with copper bonding thickness of minimum macrons and UL listed and marked = 1 no. (b) Earth enhancement material supplied in sealed bags of minimum 10 kg = 3 nos. (c) Copper strip of 150x25x6 mm, to terminate earth rod = 1 no. (d) Copper strip of 300x25x6 mm (MEEB) = 1 no. (e) Copper strip of 150x25x6mm (SEEB) = 1 no. (ii) Supply of 35 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting main earth electrode to MEEB in the equipment room in duplicate.(minimum 10 meter) (iii) Supply of 16 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting MEEB to SEEB and SPD to MEEB (minimum 10 meter ) (iv) Supply of 10 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting various equipments to SEEB (v) Supply of copper lug sleeve for 3/16 cable Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after Supply

20.00 13010300 above It includes: ( i ) Digging the earth to the required depth. (ii) Insertion of electrode. (iii) Filling of earth enhancing compound (Approx.30 Kg) (iv) Provision of exothermic weld connections to copper tape of 25 mm x 6 mm x 150 mm to the earth electrodes. All material tools and features required for weld will be arranged by contractor. (v) This also includes CC cover 1.5 ft x 1.5 ft. 1 ft wall thickness 2 inch with cover 3-inch thickness. Cables 35 Sq mm/ 16 Sq mm/10 sq mm for connecting earth to busbar, busbar to busbar and busbars to various equipments. Earth electrode of 17.20 mm Dia and 3.00 meter long high tensile low carbon steel circular rods molecularly bonded with copper and outer surface (minimum copper bonding thickness of 250 microns to made requirement of under writer's laboratories (UL) 467-2007 or latest. Copper strips of 150 mm x 25 mm x 6 mm to be welded with each earth electrode, copper strips of 300 mm x 25 mm x 6 mm for main equip- potential busbar, copper strips of 150 mm x 25 mm x 6 mm sub equip-potential busbar in relay room, power room and panel room. GI strip 25 mm x 2 mm for ring formation of earth pits Earth enhancement material in bags for each Earth Electrode. Inspection chamber of site 300 mm x 300 mm x 300 mm (Inside dimension) of approximate 50 mm thick with pulling hooks to cover the earth pits. Note: The installation of this item shall be carried out by the contractor as per RDSO/SPN/197 Version 1.0 dtd. 04.07.2016 or latest and conforming to RDSO Drg. No. S DO/RDSO/E&B/001 or latest. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after execution and testing.

4.00 182923.54 of earthing & bonding system like earth electrode, earth enhancement material, earth pit, Equi- potential earth busbar, connecting cables and tape/strips and other associated accessories in accordance with RDSO/SPN/197 Version 1.0 dtd. 04.07.2016 or latest, consisting minimum 8 Nos. of earth pits connected in a ring to achieve less than 1 Ohms earth resistance for connecting EI equipments, relay racks, panel, power equipments as per Signal Engineering Practice. Diagram of ring earth should be supplied to Railway for Approval before execution. All related material as recommended by RDSO in Spec. No. RDSO/SPN/197 Version 1.0 dtd. 04.07.2016 or latest, will be supplied by the contractor. basic material for one earth pit is given below: (a) Copper bonded steel electrode of 3.0 m long, 17 mm Dia with copper bonding thickness of minimum macrons and UL listed and marked = 1 no. (b) Earth enhancement material supplied in sealed bags of minimum 10 kg = 3 nos. (c) Copper strip of 150x25x6 mm, to terminate earth rod = 1 no. (d) Copper strip of 300x25x6 mm (MEEB) = 1 no. (e) Copper strip of 150x25x6mm (SEEB) = 1 no. (f) Supply of 35 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting main earth electrode to MEEB in the equipment room in duplicate.(minimum 10 meter) (g) Supply of 16 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting MEEB to SEEB and SPD to MEEB (minimum 10 meter ) (h) Supply of 10 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting various equipments to SEEB (i) Supply of copper lug sleeve for 3/16 cable Note: Earthing arrangement for EI must be as per RDSO guidelines issued by RDSO vide TAN/3006 dated 30.06.2025 or latest. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after Supply. NWR-PROJ-JP-S AND T/NORTH WESTERN RLY

4.00 includes installation of all components of earthing & bonding system like earth electrode, earth enhancement material, earth pit, Equi- potential earth busbar, connecting cables and tape/strips and other associated accessories in accordance with RDSO Spec. No. RDSO/SPN/197 Version 1.0 dtd. 04.07.2016 or latest consisting minimum 8 Nos. of earth pits connected in a ring to achieve less than 1 Ohms earth resistance for connecting EI equipments, relay racks, panel, power equipments as per Signal Engineering Practice. Diagram of ring earth should be supplied to Railway for Approval before execution. Installation of one earth pit includes ( i ) Digging the earth to the required depth. (ii) Insertion of electrode. (iii) Filling of earth enhancing compound (Approx.30 Kg) (iv) Provision of exothermic weld connections to copper tape of 25 mm x 6 mm x 150 mm to the earth electrodes. All material tools and features required for weld will be arranged by contractor. (v) This also includes CC cover 1.5 ft x 1.5 ft. 1 ft wall thickness 2 inch with cover 3- inch thickness. Cables 35 Sq mm/ 16 Sq mm/10 sq mm for connecting earth to busbar, busbar to busbar and busbars to various equipments. Earth electrode of 17.20 mm Dia and 3.00 meter long high tensile low carbon steel circular rods molecularly bonded with copper and outer surface (minimum copper bonding thickness of 250 microns to made requirement of under writer's laboratories (UL) 467-2007 or latest. Copper strips of 150 mm x 25 mm x 6 mm to be welded with each earth electrode, copper strips of 300 mm x 25 mm x 6 mm for main equip- potential busbar, copper strips of 150 mm x 25 mm x 6 mm sub equip-potential busbar in relay room, power room and panel room. GI strip 25 mm x 2 mm for ring formation of earth pits Earth enhancement material in bags for each Earth Electrode. Inspection chamber of site 300 mm x 300 mm x 300 mm (Inside dimension) of approximate 50 mm thick with pulling hooks to cover the earth pits. Note: Earthing arrangement for EI must be as per RDSO guidelines issued by RDSO vide TAN/3006 dated 30.06.2025 or latest. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after commissioning.

150.00 equipments on lever frame, apparatus cases, signal, relay racks, cable termination rack, block instrument etc. (supply & installation of earth electrode as per drawing no. RE/S&T/DRG/Tender/SK/398/94 for apparatus cases, signal post & other equipments as per instruction on earthing of S&T equipment. Laying of earth lead mild steel flat of size 35mmx6mm and fixing of lead MS flat to earth electrode and lever frame, signal post & apparatus cases as per Drg. No. CORE/S&T/ALD/SK/591/2008, 592/2008 and 593/2008 respectively and instructions on earthing at S&T equipment and providing cement enclosure for earth electrode as per drawing no. RE/S&T/Sig./Tender/SK/13/85 Alt. A) Note: This item requires for earthing of all the A/Cases & Signal as per RE standard. Inspection: Consignee Inspection charges: None Payment terms: 70% after supply, 20% after installation & 10% after commissioning

2.00 with temperature, Analog bar graph, Digital display, Backlight, 1000V AC/DC, measure up to 10A, Frequency Range upto 60MHz, with set of leads & carrying case. Model- Fluke 287 or Stanone/SMM180 or Keysight U1252B or Superior. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply.

2.00 For Measurement of DC/AC currents up to 60A, AC/DC Voltage up to 600V, resistance up to 40 M, Current resolution 0.1mA for low current measurements, frequency up to 60 KHz and non-contact voltage measurement function with set of leads & carrying case. Model - SCM222 or equivalent/ higher make. Motwane/Stanlay/Fluke/Megger Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply.

1.00 102122.34 resistance measurement up to 1000 ohms. Accuracy 0.1 - 0.99 : 1%, 1 - 49 : 1.5% Also measure current leakage up to 20A. No spines required for measurement Model - DECT-2 or CET500 or equivalent / higher version make Motwane/Stanlay/Fluke/Megger. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply.

1.00 500975.83 pipe locating receiver and cable avoidance tool that provide location of armoured OFC, signalling and telecom, power cable etc. Model RD8200G or STLOC10GPS equivalent or superior. Minimum specifications- Battery life- 24 hours continuous use, Backlit LCD display, IP65, multi-frequencies -12 frequencies, Variable pitch & live sound, Depth Measurement- upto 10meters depth, digital 3-digit LCD readout with ± 3% accuracy. Datalogging with export facility to .csv/excel formats. Transmitter output power- 10W with multiple power setting options, Warranty-3 years. Inspection: RITES Inspection Charges: Borne by Railway Payment Terms: 100% after Supply.

2.00 resistance with auto range 0-500 V DC. Modal: SIT 500 equivalent or superior from any reputed make Fluke or Megger or Stanone or Superior. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply.

2.00 with 3.5 digital LCD, 12.5 mm screen segment and Range -0.5 Ohms to 500 Ohms. Accuracy- ±2%. WACO or from any repudiated make. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply. Total 4541577.15 Item- 14 Miscellaneous Signalling items, Painting, Lettering S No. Item No Description of Item Unit Qty Rate Amount

25.00 & Spec. No. IRS(S) 30/64 or latest. Ward to be specified by Engineer-in- charge. Inspection: Consignee if value of whole item in work less than 10 lakhs Inspection Charges: None Payment Terms: 100% after Supply

5.00 Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply NWR-PROJ-JP-S AND T/NORTH WESTERN RLY

3.00 per specification given below:-Voltage-230V AC,50Hz, Input Power(IEC)-1000 Watt, Suction of the motor 1700 mm of water column , Airflow-30 litres/second, Dust collection capacity-61(dry), 81(wet), Variable power option-2 Speed, Blower function, Air filtraction-2 Stage, Hepa filter, Dust collection type-Washable dust bag, On board accessory storage. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply

20.00 engineer. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply

200.00 engineer. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply

3.00 Engineer incharge. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply Painting of two coats of synthetic enamel paint over one coat of primer on the following after scraping & cleaning surface wherever necessary with contractor's own supply of paints. Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in-charge. Epoxy paint will be supplied by Railways. Note: - The paint and primer should be from Asian Paints/ Nerolac/ Dulux / Berger. The primer / enamel paints (Aluminium synthetic, black enamel, brilliant white and yellow) will be as per (IS 5660 of 1970) / (IS 2932 of 1974). Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Execution

60.00 North Western Railways standard practice.

30.00 Railway's Standard Practice.

60.00 enamel only outside and ground connections with Red Oxide)

3.00 Operating console, Aluminium Lifting barriers of 24 fit long, 2 pedestal driving & driven mechanism, 2 Electric motors, 2 stop boards, 2 Nos Boom light, 2 Nos of Boom rest & Boom locking arrangements etc. (All Items at one LC gate to be taken as one LOT)

300.00 exteriors using Primer as per manufacturers specifications with two or more coats applied @ 1.25ltr/10 sqm. Over and including one coat of Special primer applied @ 0.75 ltr/10 sqm. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Execution Lettering / Numbering Termination particulars, equipments names etc., legibly and neatly inside location boxes. This includes supply of paints of Asian Paints/ Nerolac / Dulux / Berger make. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Execution

10.00 (within station limit)/indoor and outdoor equipment and all other released material of S&T at way-side station (3/4 Line). All the released material will be transported to the place/location as decided by site engineer. The item includes: i) Mechanical Signalling gears like levers, down rods, locking trough, Rodding, wire transmission, signal posts and hoods etc. ii) Electrical Signalling gears like relays, batteries, indicators, SM slide control and all released wire transmission for slot, telephone, selector control and their related items etc. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Execution Transportation of S&T material

10.00 Starting point, unloading & stacking at destination. The work is to be done as per the instructions of Railway Representative at site. Consignee will also provide gate pass / road permit to the transporter. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Execution

10.00 Inspection Charges: None Payment Terms: 100% after Execution

10.00 capacity 5 KVA or above as per requirement of Station Signalling load, for testing of Signalling system in the case of irregular Local power supply / under capacity ATs supply system at station. (Per Unit is 'Per Set Per Day'). Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Execution

1.00 includes painting of signal posts and fittings, apparatus cases, point machines, junction boxes, rail post etc. This also includes varnishing, letter writing on relays, terminal Nos., apparatus cases, point machine, Signal Nos. and other details as per Signal Engineering Manual and instructions of Engineer at site. The item includes painting of distances of main cable run from G.P nearest to cable run and painting of distances of signals from nearest line on the signals base. At least two coats of paint are to be applied besides primary coating of red oxide. This includes supply of paints, varnishes and all other material required for complete painting work at a station. This includes painting on existing functional units also. The painting shall consist of initial red oxide / base paint followed by at least two coats of the paint as per standard painting scheme. This item also includes painting of interlocked gate attached to the station. Location box no. shall be painted on both sides. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Execution NWR-PROJ-JP-S AND T/NORTH WESTERN RLY

50.00 dismantling structures including disposal of debris through dumpers etc with contractor's labour, JCB machine, machine operator, fuel etc. The contractor shall arrange for road permit for all the states for operation as per instructions of engineer incharge and vehicle shall not be more than 3 years old. Payment shall be made for actual working hrs at site. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Execution

10.00 mm x150 mm and made of 12 mm thick teakwood with a glass front, lock and sealing arrangement. All material like lock, teakwood, handles, hinges, glass sheet of 3 mm thick will be supplied by the contractor. Box will be polished and description will be written as per instructions of Engineer in charge. Inspection: Consignee Inspection Charges: None Payment Terms: 100 % after Execution Total 1218115.53 Item- 15 Telecom items (IPIS, OFC equipments, Control equipments, LC gate phones and Network equipment etc.) S No. Item No Description of Item Unit Qty Rate Amount Supply of CAT Cables / Patch Cord items

1220.00 B2-1 or latest. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply. Supply of various Optical Patch Cords

50.00 Cable as per TEC Specifications TEC 87070:2009 (TEC/GR/TX/OFJ-01/05/NOV- 09). Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

50.00 Cable as per TEC Specifications TEC 87070:2009 (TEC/GR/TX/OFJ-01/05/NOV- 09) Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

50.00 configurations SC-FC/LC-LC/LC-FC/LC-SC/SC-SC/FC-FC etc as per TEC Specifications TEC 87070:2009 (TEC/GR/TX/OFJ-01/05/NOV-09). Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply. Supply of various OFC joint enclosures

10.00 along with enclosures with heat shrinkable splice protection sleeve as per TEC Specn. TEC 87080:2025 or latest. Splice losses in no case should be more than 0.1 dB. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution.

10.00 along with enclosures with heat shrinkable splice protection sleeve as per TEC Specn. TEC 87080:2025 or latest. Splice losses in no case should be more than 0.1 dB. Inspection: Consignee Charges: None. Payment Terms: 100% after execution.

10.00 RDSO specification No. RDSO/SPN/TC/45/2013 Rev. 2.0 Amdt. 3 or latest. The item also includes supply of all the accessories of HDPE duct like end caps, collars, bends, couplers etc. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs (ii) Consignee if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

10.00 RDSO specification No. RDSO/SPN/TC/45/2013 Rev. 2.0 Amdt. 3 or latest. The item also includes installation of all the accessories of HDPE duct like end caps, collars, bends, couplers etc. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution.

10.00 work as per instructions of engineer incharge at site. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution.

5.00 as per Drg. No. CSTE/NWR/ SOR/23. It also includes supply and provision of all the material required for this item like bricks, sand, cement etc. The cement and sand should be in ratio 1:6. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution.

3.00 conductors of 6-Quad cable between stations/cable hut in presence of railway Section engineer. All equipment accessories required for the above job are to be arranged by the contractor's representative and railway's site Engineer in- charge. Testing report shall be submitted. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution. Supply of various OFC termination boxes / FDMS

10.00 and termination as per TEC Specifications TEC 87020:2010 (TEC/GR/TX /FTB 01/03/ MAY-2010) or latest. IN and OUT 48 fiber OFC cables (with all connecting materials) routing/dressing fiber as per direction of engineer/In charge. This work includes termination/splicing of fibers and testing of fibers in the section/block and report of fiber to be submitted in hard and soft copy. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution.

10.00 and termination as per TEC Specifications TEC 87020:2010 (TEC/GR/TX/FTB 01 /03/MAY-2010) or latest. IN and OUT 24 fiber OFC cables (with all connecting materials) routing/dressing fiber as per direction of engineer/In charge. This work includes termination/splicing of fibers and testing of fibers in the section/block and report of fiber to be submitted in hard and soft copy. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution. Supply of various DP boxes NWR-PROJ-JP-S AND T/NORTH WESTERN RLY

20.00 superior. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

20.00 Hensel or superior. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution.

3.00 submission for approval of Railway. The details instruction/guidelines regarding joint survey and preparation of cable route plan are enclosed in Tender document. Contractor will submit two copies of prints with soft copy for checking by Railways. If alterations are suggested by Railways, then again two copies of prints will be provided for advance approval after carrying out all the alterations as submission of final cable route plan on 75 microne standard polyester film which includes details of entire section in which Quad /OFC Cables are laid. Once Railway has approved/signed tracings for cable route plan then contractor will submit 6 (Six) sets of zerox copies for cable route plan in proper binding form. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution. Supply of indoor PVC cables

100.00 coded twisted pair switch board telephone cables PVC sheathed with nylon rip size 0.5 mm Each coil length of 100 mts of reputed make as per specification TEC GR/WIR-06/03.Mar 2002 (TEC 68080:2002) or latest. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after supply.

2.00 Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

2.00 214456.00 meter, VFL & Laser Source along with accessories. As per TEC Specification TEC 88120:2019 (TEC/GR/TX/OTD 001/05/SEP-19) Anritsu MT9085C or superior. Fiber Compatibility Single Mode, Central Wavelength (nm) 1310 & 1550 for Single Mode; Wavelength Tolerance (±) 20 nanometer, Dynamic range@ Max Wavelength 35 decibel, Event dead zone - Maximum 1 meter, Attenuation dead zone - Maximum 4 meter, Distance Measurement Accuracy (±) 1 meter, Sampling points 256000, Internal Storage OTDR traces 40000, External Storage Capacity inclusive in the scope of supply 32 gigabyte, Built-in Visual Fault Locator (VFL) / Visual Light Source (VSL), Built-in Power Meter, Power Meter input port, Dedicated Port on OTDR, Wavelength Range 850 nm to 1650 nm, Minimum Power measurement range (dBm) -70, Accuracy (Power Meter) (±) 5 percent, Connector Tip APC, Accessories inclusive in the Scope of Supply, Suitable Fiber Inspection Probe ,Suitable LAN Cable ,DC vehicle battery-charging adaptor (12 V) , Suitable VFL/VSL adapter ,Carry Case, Minimum Operating Temperature -10 degree Celsius, Maximum Operating Temperature 55 degree Celsius Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

2.00 444902.00 Accessories : AC ADAPTER /BATTERY Charger ADC-18 1PC, AC Power Cord ACC-XX: 1PC, Spare electrode Elect 2- 20:1 pair carrying case CC-30:1PC, USB cable USB-01: 1PC, Sleeve loader SL01:1 PC, dispenser AP-01: 1 PC, screw driver SC-01 1PC, Instruction manual: 1 PC, Quick reference Guide 1PC, warning & cautions: 1 PC, BATTERY RACK BRT-09, Battery charger cord DCC- 18: 1 PC, High precision Fibre cleaner CT-06: 1 PC, 3 in-1 Stripper : 1PC & Protection sleeves: 25nos. Dual monitor position with automatic image orientation, Automatic arc calibration with clever, adaptor, sheath clamp etc as per TEC Specifications TEC 88090:2024 or latest. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

2.00 88010:2013 (TEC/GR/TX/COI 002/02/ NOV-13). Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

2.00 Specifications TEC 88060:2013 (TEC/GR/TX/OPM 001/04/NOV-13), Viavi- OLP35, EXFO-EPM53X equivalent or superior. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

2.00 Inspection Charges: None. Payment Terms: 100% after Supply.

2.00 telephones of metal body with 6-pin plug as per IRS-TC-78/2020 Ver 1.1 or latest. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply. 19-inch rack items

1.00 fitting for housing the subrack LER, LSR, SDH ADMs & PD Mux or other equipments as per instruction of Railway Engineer fully wired including, Power supply distribution system, DDF, Internal wiring and other accessories, runway ladder etc. or for other application as per Drg. No. CSTE/NWR/SOR/24. The components of the rack are specified below- (i) Rack size 2035H X 600W X 600D (ii) Fixed side panels 42U X 600D (iii) Front glass door plain 42U X 600D (iv) Rear MS door plain 42U X 600W (v) Levelling screws-4 Nos. (vi) Compact Fan Module working with 48V DC or other voltage - 2 Nos. (vii) Earth connecting kit-1 No. (viii) Cable manager with cable loops-2 Nos. (ix) Krone mounting bracket-01 No (x) Caster with breaks-2Nos (xi) 20" length 1" width 5 mm thickness copper strip with 12 Nos. of holes including SS bolts & nuts for every hole to connect cables-2 Nos. (xii) 10A single pole DC MCB-2 Nos. (xiii) 6 A single pole DC MCB-2 Nos etc. The rack shall be completely wired and equipped with integrated protection modules for all channels as per technical specifications and other stipulations of tender document. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

4.00 dimension as per instruction of Engineer in charge. It includes all the accessories for fixing of the same. NWR-PROJ-JP-S AND T/NORTH WESTERN RLY

1.00 dimension, wall mounting, front glass door with lock and two key, with rack fixing Multi point AC power strip, cable organiser with wall fixing screws. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

6.00 inch standard dimension as per instruction of Engineer in charge. It includes supply of all the accessories for fixing of the same. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution. 48 volts Batteries Banks & Chargers

4.00 162840.00 Amps output in (4+1 configuration) suitable for VRLA battery as per RDSO specs: RDSO/SPN/TL/23/99 ver.4. or latest. It includes supply and wiring of min 16sq mm power cable upto load point. Inspection: (i) RDSO if value of item in work more than 10 lakhs (ii) Consignee if value of whole item in work less than 10 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

4.00 293923.58 cells, with required container and accessories like connectors, clamp, lugs, interlinks etc as per RDSO Spec. No. IRS-S-93/96A with Amnd.1 or latest. Inspection: RDSO Inspection Charges: Borne by Railways. Payment Terms: 100% after Supply.

4.00 maintenance free VRLA Batteries duly charged as per IRS Spec. No. S- 93/96(A) with amendments-1 or latest. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution.

3.00 Optical Converter) complied RDSO Specifications : SPN/TC/103/2013 Rev 2 or latest, consisting of : (1) 4 user ports 10/100mbps (2.1.3.2) without POE; (2) Two SFP slots for networking; (3) Two electrical ethernet ports for networking; (4) dual power supply support AC 230V AC / DC-48V DC from single socket; (5) 2 no. EOLS-1312-10d 1000 base - LX 10 unit work in daisy chain in ring topology. Inspection: Rites Inspection Charges: Borne by Railways Payment Terms: 100% after supply.

3.00 Ethernet to Optical Converter) complied RDSO Specifications : SPN/TC/103/2013 Rev 2 or latest, consisting of : (1) 4 user ports 10/100mbps (2.1.3.2) without POE; (2) Two SFP slots for networking; (3) Two electrical ethernet ports for networking; (4) dual power supply support AC 230V AC / DC-48V DC from single socket; (5) 2 no. EOLS-1312-10d 1000 base - LX 10 unit work in daisy chain in ring topology. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution. Electronic LC Gate Telephone system

1.00 inbuilt voice recorder. It includes supply of 'surge protection and line connection unit/circuit and centralised power supply system with battery as per RDSO Spec no. RDSO/SPN/TC/51/2021 Rev 1 or latest. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs or as per extant policy (ii) Consignee if value of whole item in work less than 10 lakhs or as per extant policy Inspection Charges: (i)Borne by Railways Payment Terms: 100% after Supply

1.00 inbuilt voice recorder. It includes installation of 'surge protection and line connection unit /circuit' and centralised power supply system with battery as per RDSO Spec no. RDSO/SPN/TC/51/2021 Rev 1 or latest. All the material required for fixing and installation of station telephone unit and gate telephone (slave telephone) will be supplied by the contractor. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution.

2.00 per RDSO spec. no. IRS: TC:82: 2005 (with Amd. 3 or latest) Inspection: RDSO Inspection Charges: Borne by Railways. Payment Terms: 100% after Supply.

1.00 equipments like control phone, magneto phone, auto phone, VHF sets, VF Repeaters etc from old station building to new station building as per instructions of site engineer. All the material required for fixing and installation will be supplied by the contractor. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution.

2.00 128011.96 Base-T ports and 04 nos. 10G SPF+ port (fully loaded) as per RDSO specification No. RDSO/SPN/TC/83/2020, Rev.2.1 or latest with redundant power supply type. Make: Cisco/Juniper/Tejas or superior. Inspection: RDSO/RITES Inspection Charges: Borne by Railways Payment Terms: 100% after Supply. Passenger Information System related items

1.00 Synchronization in standalone mode as per Clause 5 of RDSO SPN TC 62/2008, (Rev 4.1) or latest with all required accessories. Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs or as per extant policy (ii) Consignee if value of whole item in work less than 10 lakhs or as per extant policy Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% after Supply

1.00 area with GPS Synchronization in standalone mode as per instruction of site incharge with all required accessories and fixing arrangements to commissioning the item. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after commissioning.

1.00 in standalone mode as per Clause 6 of RDSO SPN TC 62/2008, (Rev 4.1) or latest Inspection: (i) RDSO/RITES if value of item in work more than 10 lakhs or as per extant policy (ii) Consignee if value of whole item in work less than 10 lakhs or as per extant policy Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% after Supply NWR-PROJ-JP-S AND T/NORTH WESTERN RLY Total 6007975.82