SPECIAL REPAIR TO BATHROOMS AND BARRACK OF BLDG NO P 35C OF VARIOUS UNITS AT JALIPA MIL STN UNDER GE A BARMER

Amount

Taking down cement plaster on stone walls/ ceiling including raking out joints, hacking for key, scrubbing down with water etc complete.

M&L for Plastering 15mm thick in CM (1:4) on stone wall surface (external wall surface) finishing the surface even & smooth with mixing of water proofing compound as per manufacturer’s instructions. (Note:- Water proofing compound shall be measured and paid separately as supply only rate)

M&L Plastering 15 mm thick in CM (1:6) on stone wall surface finished even and smooth without using extra cement on internal wall all as specified and directed.

M&L for plastering 5mm thick in CM 1:3 in (concrete surface) ceiling finished even and smooth without using extra cement all as specified and directed.

M & L for Preparation of new plastered surfaces of wall and applying two coats of cement base paint all as specified and directed.

M & L for Preparation of old painted surfaces of wall and applying one coat of cement base paint all as specified and directed.

M&L for Preparation of new plastered surface of ceiling and applying three coats of white wash all as specified and directed.

M&L for Preparation of old white washed surface of ceiling and applying 2 coats of white wash all as specified and directed.

M & L for preparation newly plastered surfaces of wall & applying a layer of wall care putty including cornices etc for proper levelling of plaster and two coat of oil bond distemper over a coat of primer complete all as specified and directed.

M&L for complete removal of existing treatment on walls and prepare the wall surface with wall care putty and then applying two coats of distemper oil emulsion white or tinted over a coat of primer complete all as specified and directed.

Taking down shutter of any description exc 1 Sqm but n exc 2 sqm each all as specified and directed.

Refixing shutters in same opening of any description exc 1.00 sqm but n. exc 2.00sqm each all as specified and directed.

S&F IInd class hard wood 35mm thick Factory made plain framed panelled shutter any number of panels of timber flat on both sides, with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces the size of rail and stile as per IS 1003 (Part-I) kiln seasoned and chemically pressure treated.

Taking down unserviceable chowkhat or frame with shutter (without taking off shutter from the frames) exc 1.5 sq.m but n. exc 4 Sqm each all as specified and directed.

S & F Pressed steel frames of size 165X 60mm and 1.25 mm thick for doors with double or single rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified.

S & F Pressed steel frames of size 105X 60mm and 1.25 mm thick for doors with double rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified.

Taking down chowkhat or frame with shutter (without taking off shutter from the frames) n. exc 1.5 Sqm each

S&F factory made 35mm thick 2nd class HW glazed and skelton shutter and open rebated and prepared to receive glass, gauze etc (without sash bars), edges of framing, plain, chamfered or rounded. fitted with cut and mitred beads for securing glass etc; size of members of shutter as specified in SSR Part I section 8 clause 8.24 (a) supplied and fixed to chowkhats.

S&F stainless steel wire cloth 8 percent nickle 0.20mm nominal dia of wire and average width of aperture 1.40mm.

S & F in repair 300 mm long brass, ordinary rat tail rod pattern springs including roller and roller plate complete

M&L for preparation of new wooden surfaces of any description over 10cm width or girth & priming coat with pink primer and applying two coat of synthetic enamel paint all specified.

M&L for preparation of old wooden surfaces of any description over 10cm width and applying one coat of synthetic enamel paint all specified.

S& F solid PVC door frame of size 50x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification & drawing.

S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strips of 20mm width stuck inside with solvent cement for tiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed the stiles and rails with suitable PVC Sheet beading and jointed together with solvent cement supplying & fixing in the frame at site all as specification and drawing .

S&F barrel tower bolt 150mm long aluminium anodised extruded section all as specified

S&F aluminium anodised handle 150mm long cast type all as specified

S&F butt hinge size 100mm extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed.

S & F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

Taking down unserviceable glazed steel windows, fly proofing steel windows and ventilators etc

S&F MS square bar for window guard bars fixed independently welded to ventilators and windows etc and similar article all as specified and directed by Engr-in-Charge.

S&F steel ventilators with top hung shutters including box type hinges, steel peg stay complete

S & F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dove tailed or welded (Glazed steel window) all as specified and directed.

S &F steel windows with side hung shutters including box type hinges, steel handle with fixing arrangement for wire gauge windows etc complete (wire gauge steel window) all as specified and directed.

M&L preparation of new or previously untreated steel surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red- oxide, zinc chrome primer complete all as specified & directed by Engineer-in-charge.

M & L for rendering 15mm thick in Cement mortar 1:3 for work in (Chajja and Facia downward/upward face ) isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work including cutting to edges, all mitres and stopped ends including necessary scafolding all as specified & directed by Engineer-in-charge.

Demolition of Precast concrete block walling built in cement mortar all as specified & directed.

M & L for precast cement concrete block masonry with solid blocks (casted in cement concrete type C1, 1:3:6 using 20mm graded aggregate) and setting in cement mortar 1: 6 complete.

M & L for providing of 20mm thick Granite (Black colour) one side machine polished in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including 15 mm thick screed bed in CM 1:6 etc complete all as specified and directed by Engineer-in-charge.

Grinding and polishing for half rounding of granite stone edges etc all as specified and directed by Engr-in-Charge.

Dismantling of cast iron pipe including fitting jointed in cement or led joint 100 mm bore.

Dismantling of cast iron pipe including fitting jointed in cement or led joint 75 mm bore.

S&F cast iron soil, waste and vent pipe in any length with or without ears with cement joints fixed to wall for the following sizes:-

100mm bore

75mm bore

S&F cast iron soil, waste and vent pipe laid in trenches or in floor with cement joints for the following sizes:-

100mm bore

75mm bore

S&F cast iron cowl suitable for 100mm bore pipe

S&F CI branch pieces single equal or unequal ordinary or inverted (Spigot or socketed type) or with parallel branches with door for the following sizes:-

100mm bore

75mm bore

S&F cast iron bend with door for the following sizes:-

100mm bore

75mm bore

Taking up or down steel tubing and connections for the following sizes:-

15 mm bore pipe

25mm bore pipe

S&F GI tubing medium grade including all fittings fixed to walls and ceilings or laid in floors of following sizes :-

15 mm bore pipe

25mm bore pipe

Relaying /Re - fixing Old water tubing 15mm dia (bore) and connections in new or old position after cleaning both inner and outer surfaces of pipes including provision of New GI fittings (as ordered), complete all as specified and as directed.

Relaying /Re - fixing Old water tubing 25 mm dia (bore) and connections in new or old position after cleaning both inner and outer surfaces of pipes including provision of New GI fittings (as ordered), complete all as specified and as directed.

Dismantling and taking down water storage tanks of 500 Ltr capacity and S&F 500 ltrs capacity rotational moulded polyethylene white three layer water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including S&F of ball brass valve high pressure of 20mm dia complete all as specified and directed.

S&F in repair stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe of 25mm bore.

S&F in repairs bib tap, 15mm bore, fancy type, chromium plated screwed down screwed for iron pipe or for brass ferrule complete.

S&F in repair vitreous China wash hand basin of size 550x450mm with CI bracket and comprising of the following:- (a) Waste fitting 32mm dia brass chromium plated with long screwed shanks and fly nut, flange end bedded in red lead cement and other end fixed. (b) Pillar tap cast copper alloy with capstan head chromium plated, screwed down, high pressure with or without lettered hot or cold with long screwed shank and fly nut. (c) PVC waste pipe 32mm dia 600mm long. (d) PVC Connection 15mm size with PTMT nuts of length 450mm long.

S&F CP fancy type stop valves/Angle valves screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed to 15mm bore dia pipe complete all as specified.

S&F in repair vitreous china squatting pan "Orissa' pattern size 580x440 mm white with integral foot rest including 'P' or 'S' trap complete all as directed.

S&F in repair 10 Ltrs PVC valveless, syphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and connection to pipes and fixing of lever complete all as specified and directed.

S&F in repair PVC connection 15mm size 450mm long with brass fly nuts and washers on both ends complete.

S &F chromium plated shower roses with or without swivel joints, 125mm in size including fixing to steel pipe or union complete all as specified and as directed.

S & F in repairs Cast iron nahani trap 75mm dia, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete.

Roughening surfaces of old concrete floor by picking, sweeping, cleaning and washing down with water to remove dust, etc all as directed.

M&L Cement concrete 1:2:4 type B0 using 12.5mm graded aggregate stone aggregate 25 mm thick complete all as specified and directed.

Finishing cement concrete surface even and smooth without using of extra cement in sub bases of floor/paving complete all as specified and directed.

S&F for Glass dividing strips, 3mm X38mm thick and inserted in position, conform to design specification all as directed.

Demolition of wall/ floor tiling of any description including back coat, removing the debris & rubbish off from the premises all as directed.

M & L for coloured glazed ceramic tiles size 300x450x7 mm thick on vertical surface of wall over and including 10mm thick backing coat in CM 1:4 set and jointed in neat cement slurry and pointed in white cement/coloured cement to match the tiles.

M & L for non skid ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles and including 20 mm thick screed bed in CM 1:6

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass self 12cm wide with chromium plated bracket guard and railing 60cm wide, complete all as specified and as directed.

M&L Machine cut Kota stone slab flooring (In one piece only)18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing, polishing and rounding to edges of Kota stone including 15mm thick back coating layer in CM 1:6 complete all as specified.

M&L Machine cut Kota stone in vertical surface (In one piece only) 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing, polishing and rounding to edges of Kota stone including 15mm thick screed bedding layer in CM 1:6 complete all as specified.

Polishing cutting & grinding clean to existing Kota stone floor and removing of all impurities and making clean all as specified and directed by Engr-in-Charge.

M&L for 40 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in floors, roof padding & finished the surface even & fair without using extra cement including mixing approved water proofing compound as per manufacturer's instructions. (Note:- liquid water proofing compound shall be measured and paid separatly)

M&L for laying of APP based polymeric membrane minimum weight 3Kg/Sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt not less than 150gm/sqm) laid on primed surface by torched application complete etc all as per manufacturer instructions and sealing all the over laps of 75mm in length side and 100mm on the width side of membrane all as specified and directed including following (i) Preparing the surface of roof slab by brushing with wire brushes for removing of loose/ dirt material etc and sweeping with brooms or gunny bags or mechnical devices (ii) Applying neat cement slurry with 3Kg of cement per sqm & mixing of liquid water proofing compound as per manufacturer instruction on surface of roof slab (iii) Plastering 10mm thick in CM (1:3) on concrete surfaces with mixing of liquid waterproofing compound as per manufacturer’s instructions and finishing the surface even and smooth without using extra cement (iv) Priming the suraface of concrete/plaster with bituminous primer 0.4 liter per Sqm (Note:- liquid water proofing compound shall be measured and paid separatly)

Supply only liquid water proofing compound

M & L for Providing cement concrete(1:2:4) type Bo(using 12.5 mm graded stone aggregate) for coved fillets of radius 75mm provided at junction of roof and parapet/vertical surfaces, padding concrete to achieve slope as required & making platform for water tank on roof slab etc.

M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings kitchen platform, chajjas , staircase slab and similar work; not exceeding 200mm thick (Horizontal or sloping) all as specified.

M&L Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide all as specified.

Providing & erecting double scaffolding, Jacks to support the structure provisionally during repair etc.

Dismantling portions of reinforced cement concrete work ordered/chipping of unsound concrete to a depth/thickness of 25mm to 100mm averaging 62.5mm in respect of roofs, floors, beams, columns, staircases, landing, chajja, parapets, etc. and similarly suspended work (other than ground floors) complete as specified.

M&L Surface preparation of RCC column, beams, chajja, roof drops, soffit of slabs(ceilings) by removing existing cement plastering, hacking the surface of RCC work for key to a depth of 15mm by gentle chipping manually to make surface rough and thoroughly cleaned with air and water jet .

M&L for preparation of exposed surface of rusted steel reinforcement with metal wire brush, cleaning the rusted surfaces free from loose rust and application of rust remover cum passivator painted with brush to rusted [email protected]/Sqm. of surface of existing reinforcement) and removing rust with flex after 24 hours of application of rust remover with the help of wire brush, sand paper and thoroughly washed with water using pressure jet and allowing it to dry complete. (Area of cleaned reinforcement steel bar shall be measured for payment) Density: 1.01 Kg/1 at 30o C

M&L for Preparation of surfaces of steel reinforcement by cleaning thoroughly and providing, mixing and applying zinc anti-rust agent as per manufacturers method of application to rebar corrosion protection system to reinforcement @3.75 Kg/Sqm surface of steel reinforcement in two coats complete all as directed.

M&L for augmentation of RCC using Dr. Miracle system by pressure grouting @ 1-2 Kg/sqm pressure all as specified and directed. Make:- Aayka Polymers/ Fosroc/ Pidilite/ Sika/ Dr Fixit

M&L for providing & fixing AQUAVENTS-moisture release system for Roof all as specified and directed. Make:- Aayka Polymers/ Fosroc/ Pidilite/ Sika/ Dr Fixit

M&L for providing & fixing AQUAVENTS-moisture release system for Walls all as specified and directed. Make:- Aayka Polymers/ Fosroc/ Pidilite/ Sika/ Dr Fixit

M&L Polymer modified AQUAPROOF102 @4kg/Sqm polymer coat with MRP glass membrane, prepared and applied on the roof-Khurras, junctions, cracks etc. all as specified and directed. Make: Aayka Polymers/ Fosroc/ Pidilite/ Sika/ Dr Fixit

M&L ESKOO heat reflective cum waterproofing system @ 2kg/sqm all as specified and directed. Make: Aayka Polymers/ Fosroc/ Pidilite/ Sika/ Dr Fixit [Roof]

M&L for laying Micro-concrete cement based pre packed single component, chloride free, sulphate free, non-shrink, free flow, self compacting/ready to use after mixing water in specified proportion of approved quality. Form work shall be provided for placing micro concrete patch repair as required at site with steel jack system and steel props to support the form work in this application of high strength, dual shrinkage, compensated, micro, concrete repair with compressive strength of 40 Mpa at 28 days. Make: Aayka Polymers/ Fosroc/ Pidilite/ Sika/ Dr Fixit Note: form work shall be measured and paid separately.

Providing & fixing 12mm TS dowel pins/ staple/ shear pins including drilling holes in concrete, providing labour, epoxy for grouting the pins Make:- Aayka Polymers/ Fosroc/ Pidilite/ Sika/ Dr Fixit

Providing & fixing 6mm TS dowel pins/ staple/ shear pins including drilling holes in concrete, providing labour, epoxy for grouting the pins Make:- Aayka Polymers/ Fosroc/ Pidilite/ Sika/ Dr Fixit

M&L for cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water pipe etc and making good cutting not exc 10cm complete all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St. 240 as in frame work for sun shade, roof projection and wall partition etc. complete all as specified and directed.

M & L factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2,4,or 6 raised panel design with 2mm thick moulded colour PVC prelam sheet on the front face & 2mm thick moulded colour PVC prelaminated sheet on back face, supplying & Fixing in frame at site as per specification complete all as specified and as directed.

Taking down copper/aluminium point wiring for (light, fan, socket or power) complete including unserviceable fittings such as switches, ceiling rose, holders, sockets etc. and making good the disturbed surfaces on wall/floor etc complete all as specified and directed.

M & L for point wiring with 1.5 Sqmm (nominal area) PVC insulated, unsheathed, multistranded, 1100 volts grade copper conductor cable single core, drawn through with and including non metallic PVC conduit and its accessories complete fixed to walls/ceiling etc including one run of 1.5 Sqmm PVC insulated copper conductor cable green in colour for continuous earthing, 1.6 mm thick MS terminal box finished to wall with 3 mm thick laminated hylam sheet top cover all as specified for the following:- Note:- Surface Conduit shall be laid in ceiling portion only.

One light/fan/bell point controlled by one one way switch.

One 3/5 pin 5 amps socket point on independent board

One 3/5 pin 5 amps socket point on same board

One light point controlled by two way switches

M & L for pointing wiring with 4 Sqmm (nominal area) PVC insulated, unsheathed, multistranded, 1100 volts grade copper conductor cable single core for 3 pin socket outlet 15Amps independent board, drawn through with and including non metallic PVC conduit and its accessories including one run of 4 Sqmm PVC insulated copper conductor cable green in colour for continuous earthing, 1.6 mm thick MS terminal box finished to wall with 3 mm thick laminated hylam sheet top cover all as specified.

M & L for pointing wiring with 4 Sqmm (nominal area) PVC insulated, unsheathed, multistranded, 1100 volts grade copper conductor cable single core for one 5/6 pin 16Amps socket outlet on independent board, drawn through with and including non metallic PVC conduit and its accessories including one run of 4 Sqmm PVC insulated copper conductor cable green in colour for continuous earthing, 1.6 mm thick MS terminal box finished to wall with 3 mm thick laminated hylam sheet top cover all as specified.

S&F switch piano, flush type single pole, one way 5 Amps

All as per Item No 99.00 above but 15 Amps

S&F switch piano, flush type single pole, two way 5 Amps

S&F socket outlet 2 in 1, 3 pin, 5 and 15 Amps flush type

S&F socket outlet 2 in 1, 3 pin, 5 Amps flush type

S&F switch socket combination 2 in 1, 5Amps, flush type complete.

S&F switch socket combination 5 in 1, 5/16Amps, flush type complete.

S&F bell push, flush type, 5 Amp complete.

S&F buzzer, ding dong AC, 230V, single pole complete.

M&L in repair integrated LED channel tube light fittings, 1 x 20W, 230v, Energy efficient Box type, integral sleek polycarbonate with white acrylic cover epoxy powder coated with fluorescent tube light 1 x 20 w, etc. complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed by Engineer-in-charge.

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet as required.

S&F ceiling fan with regulator 1200 mm sweep including connection from ceiling rose with flexible copper twin core 23/.0076 connect to ceiling fan complete all as directed by Engr-in-Charge.

Supply and fixing Exhaust fan single phase, 450 mm sweep, 240 volts with louvers to be fixed in kitchen / bathroom complete including connection with twin core flexible wire of size 23/0.0076 complete alongwith 1.5 Sqmm copper stranded earth wire all as directed by Engr-in-Charge.

M&L ceiling rose, 3 phase PVC/polycarbonate, isolated body all as directed by Engr-in-Charge.

M&L for lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings all as directed by Engr-in-Charge.

S&F in repair LED light fitting,1x9 w bulk head luminaries, with lamp holders and LED bulb, etc.complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V, 50HZ all as directed by Engr-in-Charge.

S&F LED lamp 9 watt all as directed by Engr-in-Charge.

Taking down unserviceable main switches, DBs, bus bars chambers including all fittings and fixtures etc complete from existing main boards and removing from site all complete all as directed by Engineer-in-Charge.

Taking down unserviceable sub main wiring with copper/aluminium conductor, PVC insulated cable of any size drawn through rigid steel conduits/ PVC casing-caping including earth wire accessories etc complete and removing materials from site as directed.complete all as specified and as directed by Engineer-in charge.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth. complete all as specified and as directed by Engineer-in charge.

S & F Sub main wiring with 6 Sqmm (Nominal area) with two runs (Red for phase and Black for neutral) of single core, PVC insulated, multistranded, unsheathed, copper conductor cables 1100 V grade drawn through PVC conduits/casing-caping fixed to wall/ceiling etc including 6 sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, copper conductor green in colour as earth wire and duly connected to earth point complete as specified and directed.complete all as specified and as directed by Engineer-in charge.

S & F Sub main wiring with 4 Sqmm (Nominal area) with two runs (Red for phase and Black for neutral) of single core, PVC insulated, multistranded, unsheathed, copper conductor cables 1100 V grade drawn through PVC conduits/casing-caping fixed to wall/ceiling etc including 4 sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, copper conductor green in colour as earth wire and duly connected to earth point complete as specified and directed.complete all as specified and as directed by Engineer-in charge.

S&F in repair Sheet metal enclosure (DB) triple pole and neutral 4 way, 415 Volt with 200 Amps rated bus bar all as directed by Engr-in-Charge.

S&F in repair Sheet metal enclosure (DB) Single Pole and neutral 8 way, 415 Volt with 200 Amps rated bus bar all as directed by Engr-in-Charge.

S&F in repir Isolator 4 pole 63 Amps

S&F in repair Isolator SPN 40 Amps

S&F in repair MCB SP 6-32 Amps

Supply and fix in repair Power line vertical type DBs in double door, detachable gland plates for flush/surface mounting with bus bar neutral link and earth bar without mcb's suitable for TP/FP MCCB's as incomer comprising of MCCB TP 100 amps 25 KA - 01 as incoming and suitable space for outgoing mcb's complete all as specified and as directed by Engr-in-charge.

Supply and fixing in repair Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20Amps all as directed by Engr-in-Charge.

M&L for earthing complete with galvanized steel earth plate electrode of size 60cm x 60cm x 6mm thick burried directly in ground vertically at a depth not less than 2.25 metre deep below normal ground level with top edge of the plate not less than 1.5 metre below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal dust and common salt, filling in alternate layer and electrode connections by using galvanized iron earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers made of galvanized iron or steel and protected by light grade 15 mm dia GI pipe connected to main switch board or main control board, and GI pipe light grade 20 mm bore for watering and including funnel, wire mesh, RCC pit cover and PCC chamber pit with PCC 1: 2: 4 type C2 including excavation and earth work, disposal of surplus soil to a distance not exc. 50 mtr all as specified and as shown on Plate No 3 of SSR Part I (2010) including dismantling of existing unserviceable earth pit all as specified and directed by Engr-in-Charge.

M&L Earth continuity conductor or main earthing lead fixed to valve on batten or recess or chases or buried in ground or drawing in conduit or any other situation for loop earthing etc as reqd 4 mm dia galvanized steel wire all as specified and directed by Engr-in-Charge

Taking down unserviceable ceiling / exhaust fan any make and size from site and depositing to E/M yard/store duly rectifying the defects (replacing of ball and bearing, rewinding, oiling / greasing etc.) and make it serviceable in all respect including painting and marking MES No complete all as specified and as directed by Engineer in Charge.

S&F Factory made Double door board distribution in sheet steel enclosure with 200 Amps rated bus bar, TPN, 4 way, 440 Volts suitable for housing MCBs.complete all as specified and as directed by Engineer-in charge.

S&F Factory made Double door board distribution in sheet steel enclosure with 200 Amps rated bus bar, SPN, 8 way, 240 Volts suitable for housing MCBs.complete all as specified and as directed by Engineer-in charge.

S&F in repair MCB, TPN, 440 Volts, 63 Amps.(Make:- Havells, Model No - DHMCCSNF006-063) complete all as specified and as directed by Engineer-in charge.

S&F in repair MCB, SPN, 240 Volts, 5 to 32 Amps.(Make:- Havells, Model No - DHMCCSNF006-032) complete all as specified and as directed by Engineer-in charge.

S& F in repair MCB, SP, 240 volts, 5 to 32 Amps.(Make:- Havells, Model No - DHMCCSPF006-032)complete all as specified and as directed by Engineer-in charge.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, laying of cables etc and getting out in hard/dense soil complete all as specified.

Removing excavated material (Soil) n.exc 50 m and depositing where directed at a level n. exc 1.5 m above the starting point complete all as specified.

Returning, filling in including spreading, leveling, watering and well ramming in layers not exc. 25cm depth in soil.

Supply and spreading clean dry sand in trenches for cushioning all as specified for cable protection complete all as directed.

M & L for 40 to 50 mm thick roughly hammer dressed stone slab 25 to 30 cm wide & not less than 60 cm long laid down in trenches connecting to each other with gaps between adjacent slab not exceeding 10 mm over under ground cable for protection complete all as directed at site.

Supply and fix Galvanised steel tubing, light grade, with fittings and MS clamps, nuts, bolts etc of 50 mm dia bore for cable protection on pole, road crossing or ground in pillars for fixing gate light etc complete all as specified.

Supply and lay XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured electric power cable (heavy duty) 1100 Volts grade with stranded aluminium conductor of 25 Sqmm 4 core

M&L for boring/drilling by machines/manual horizontally under the road in any type of soil without cutting/disturbing the existing road and inserting GI pipe of any size for drawing the cable complete all as specified. (Note:-GI pipe shall be measured and paid separately.

Kusum Traders

National Rewinding Works