Renewal Replacement furniture in lieu of surveyed off

Bath mat PVC All as speicified in Drg with top size of 400x300x250mm edge moulded PVC sheet of top should be 5mm thick 3x10 stiffener moulded along with the seat in single piece a leg of 25mm dia should be at centre and Rubber shoe will be provided at legs Rest all as per shown in drawing and as approved by GE

Chair Dining Officer All Wood work legs rails back stopper and stiffeners etc shall be of 1st class HW Teak MP Teak well seasoned all as specified and shown in drawings All the wooden joints shall be fixed with bamboo pins and nails shall not be used Seat shall be 75mm thick of polyurethane foam density of 40 Kg obligue cum covered with acrylic fabric of polyster polyurethane and upholstered with good quality tapestry cloth of approved make and shade Plywood for seat shall be 12mm thick BWR phenol bonded commercial grade All wooden portion shall be smoothened and shall be applied with best quality of franch polish till attaining glossy finish PVC rings of approved pattren shall be screwed to the base of each leg Rest all as specified and shown on drawing and approved by Engineer in charge or GE

Chair Dining All as shown on drawing Overall size shall be 440mm long 430mm wide and 890mm high All wood shall be first class hard wood teak Front legs shall be 30mmx55mm in section through out up to 460 mm high Rear legs shall be 30mmx55mm in section and 890mm high The distance between outer side of legs in front shall be 440mm and the distance between outer side of legs in the rear shall be 405mm The legs shall be joined with front sides and rear rails made to shape out of 30mmx65mm in section Two side stiffner in short sides shall be provided of 20mm x 25mm in section One stiffner of 20mm x25mm in section shall be provided in the middle of short stiffner joining short stiffners Back horizontal rests two in numbers of 45 mmx15mm made slightly curved in shape out of 45mmx35mm in section wood shall be provided one at 18mm below the top of rear legs and other below 45 mm from the bottom of top horizontal rail Caning shall be done without any joint in the cane The cane shall be 2 mm wide 0 point 4 mm thick half round gola type woven in Godrej pattern The cane shall weight not less than 6 gms per ten running meter All wood surfaces exposed to view when placed in position shall be French polished with high gloss finish Hard rubber or PVC shoes shall be screwed to the bottom of all legs Rest all as per shown in drawing and as approved by GE

Chair Writing All as shown drawing Over all size shall be 535mm long 470mm wide and 890mm high All wood shall be of first class hard wood teak Front legs shall be of 55mmx30mm in section and 660mm high upto bottom of arm rest Rear legs shall be of 55mmx30mm in section and 890mm high The distance between outer legs in front side be 535mm and between outer side of legs and rear shall be 470mm The legs shall be joined together at 460mm from bottom of legs by front sides and rear rails 30mmx65mm in section made to shape as shown on drawing Side Stiffners in 470mm side and at 100mm from bottom of legs shall be provided of 25mmx20mm in section stiffners One stiffner of 25mmx20mm in section shall be provided in the middle of side stiffners joining side stiffner two arm rest of 60mmx25mm in section made to shape as shown on drawing shall be provided on the side arms Two back horizontal rest 50mmx15mm in section made slightly curved out of 50mmx35mm in section wood shall be provided one at 20 mm below the top of rear legs and other at 45 mm below the bottom of upper top rest Caning shall be done with 2 mm wide and 0 point 4mm thick half round gola type cane woven as per Godrej Patern The cane shall weight not less than 6 gms per ten runing metre The weaving shall be done without any joint in the cane The cane shall be of Shah or Premier brand All wood surfaces exposed to view when placed in position shall be French polished with high gloss finish Hard rubber or PVC rings of 25 mm dia and 25 mm high shall be scruewed to the bottom of all legs Rest all as per shown in drawing and as approved by GE

Chair Easy cushioned All as shown on drawing All wood shall be of first class hard wood teak Front legs shall be 70mmx25mm in section 520mm high Rear legs shall be of 70mmx25mm in section slanting 185mm horizontally in the height of 490mm Front and rear rails shall be provided below the seat joining front legs and rear legs Front legs shall be 510mm apart and ear legs shall be 480mm apart The top of front legs shall have wooden arms rest of 65mmx25mm in section and 610mm long made to shape as shown drawing The legs shall be joined by side rails of 70mmx25mm in section teak wood The bottom frame of seat shall be of 55mmx20mm in section over which 3mm thick plywood commercials shall be fixed 75mm thick foam cushion of 32 density with upholster with tapestry cloth of approved shade and texture as approved by GE The side frame of back rest shall be of 70mmx25mm in section joined with seat and rear legs as shown on drwaing and fixed back support of 55mmx20mm in section fixed horizontally between side frames of back reast 3mm thick plywood commercial shall be fixed over the wooden frame of back rest over which 50 mm thick 32 density foam upholstered with tapestry cloth of appoved shade and texture and quality as shown on drawing as approved by GE All wood surfaces exposed to view when placed in position shall be French polished Hard rubber or PVC shoes of 25mm dia and 25mm high shall be provided to the bottom of legs with screws Rest all as per shown in drawing and as approved by GE

Chair Easy All as shown on drawing All wood shall be of seasoned first class hard wood teak Legs of chair shall be of 55 mmx25mm in section at place under side arm rest tapering to the bottom of legs to 25mmx25mm in section Front legs shall be joined by 50mmx25mm in section rails provided below seat frame for the support of frame Rear legs shall be 55mmx25mm in section below arm rest and 25mmx25mm in section at the bottom of legs Rear legs shall be joined together by rear rails of 50mmx25mm in section provided at the bottom of seat frame Seat frame shall have the rear horizontal put of section 70 mmx40mm joining the sides of frame which shall be 70mmx40mm at the back and 25mmx25mm in section near the front rail The front rails of seat shall be out of 55mmx25mm in section teak wood The seat frame shall be of size 510mm long in front and 480mm long at rear 575mm deep The top horozontal rail of back reast shall be out of 55mmx40mm and shall be 50mmx20mm The bottom horizontal grame of back rest shall be 55mmx20mm in section The sides of back rest shall be join the seat of chair and shall be out of 70mmx25mm made to shape as shown on drawing The arm rests out of 65mmx25mm in section and 610mm long shall be provided in shape as shown on drawing Seat and back shall be woven with plastic cane of 2mm wide 0 point 4 mm thick Shah or Premier brand in Godrej Pattern Hard rubber rings PVC toes shall be provided to bottom of all legs with screw All wood surfaces exposed to view when placed shall be French polished with high gloss finish Rest all as per shown in drawing and as approved by GE

Peg table All as shown on drawing Over all size shall be 450mm long 300mm wide and 380mm high Legs shall be of teak wood of section 30mmx50mm The legs shall be 362mm high 5mmx5mm in section groove shall be provided on the top of legs which shall be visible when placed in position Two numbers top rails of section 20mmx40mm of teak wood shall be provided connecting legs in short sides Bottom rails shall be fixed at 100mm from the bottom of legs Top of table made out of 18mm thick both side pre laminated particle board exterior grade teak shade with well chamferd teak wood edging 6mm thick allround using synthetic adhesive and headless nails jointed in mitre joint duly french polished shall be provided All wood surfaces exposed to view when placed in position shall be French polished with high gloss finish Rest all as per shown in drawing and as approved by GE

Sofa Set 4 seates with cushion The sofa set 4 seater shall consist of two single seats All wood shall be of first class teak wood Legs of sofa set shall be 70mm x35mm in section teak wood Front legs shall be jointed by 100mm x 35mm in section wooden rail in front Front and rear legs shall be joined with 100mm x 35mm in section wooden rails in sides 100mm thick seat cushion and back cushions shall be of size 530mm x 560mm one numbers in seat and one numbers in the back The cushion shall be of cool foam or any other superior quality foam of 40 density as approved by Engineer in charge Cushion shall be covered with approved color tapestry cloth as directed by Engineer in charge Rest all as per shown in drawing and as approved by GE

Table 900x900x760mm wooden All as shown on drg Overall size shall be 900mm long 900mm wide and 760mm high All wood shall be of sirst class hard wood teak Leg shall be four in numbers Leg shall be 55mmx35mm in section and 740mm high Top top of leg shall be jointed togetther in short and long side with 25mm x75mm wooden rails the top of table shall be of 19mm thich pre lamanated particle board 4mm thick teak wood edging shall be fixed all round the edge of top of table 25mmx3mm flat iron 200mm long made into right angle shall be provide on the inner side of four corners of the table Eight numbers 20mmx3mm flat iron 200mm long bent to shape as right angle shall be provided at all joints joining legs with top rail as directed by Engineer in charge All wood surface exposed to view when placed in position shell be french polished with high gloss finish Hard rubber or pvc shoes of 25mm high shall be screwed to the bottom of all legs Rest all as per shown in drawing and as approved by GE

Table Dining 6 Persn All as shown on drawing Over all size shall be 1500 long 900mm wide and 760mm high All wood shall be first class hard wood teak Leg shall be of 75mmx40mm in section and 722mm high 5mmx5mm in section grove shall be provided inthe visible portion of top of legs 25mm thick and 100mm high top rails shall be provided in short and long sides joining the legs at top Two numbers teak wood stiffeners 100mm wide and 25mm thick shall be provided equally spaced joining the top long side top rails Eight numbers wooden corners shall be provided joining legs with top rails The shape shall be as directed by Engineer in charge Wooden corners shall be fixed with four screws Top of table shall be of 18mm particle board 4mm thick teak wood edging shall be provided all round the top edge of table All wood surface exposed to view when placed in position shall be french polished with high gloss finish Hard rubber toes 25mm dia and 25mm high shall be provided to bottom of all legswith screw Rest all as per shown in drawing and as approved by GE