Request for Proposal (RFP) Construction and Setting up of Incubation Center at Bikaner, Churu and Pali

Amount

Civil -Supply and Execution of following items

Demolishing/dismentling manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material .All lead and lift from site upto 5km outside the site (dispose of the material) at safe place

Brick work, Stone Masonry, Plastering, Flooring/ Dadooing /skirting/tiles all types (L.S.)

Joinery( door, window, ventilator, vent, WC, urinals, wash basin,exisiting railing & MS shutter) and handing over to local authorities (L.S.)

Providing and fixing of W.C. pan (any type including WC cover,SS jali, health Facuets,cistern 10 liters etc all accesories), Urinals and wash hand basinincluding pillar cock,angle valve,connection pipe,outlet pipe,ss jali of all sizes with care including all necessary fittings P or S trap. Cost to include if any repair of pipe work or new pipe to be installed in all manners. Toilets to be handed over in working conditions

Half brick masonry in Superstructure , above plinth level upto floor V level using bricks of designation 75 Cement mortar 1 : 6 (1 cement : 6 coarse sand)

Brick work with FPS briks of class designation 75 in superstructure above plinth level upto floor 5 level in all shapes and size.. In Superstructure in cement mortar 1:6 (1 cement : 6 fine sand)

Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead : With cement mortar 1 :4 ( 1 cement : 4 coarse sand)

Preparing the surface and plaster all internal RCC/ masonry surface with cement mortar 1:6, 20mm thick, smooth finished to line and plumb at all levels including all leads and lifts with necessary scaffolding, curing, hacking the surface, etc., complete.

Providing and erecting structural steel members in position at all levels and heights as specified in the drawings made out of standard MS sections conforming to IS 226/ 2062/ 800. Cost to include fabricating necessary gusset plates, stiffener plates, brackets, bolts, cleats, seating angles, etc., to the required size, shape, alignment, etc., as per the drawings. Cost to include welding of members using structural steel welding electrodes as per IS 814/ 816/ 817, testing as per IS 7307 (PART 1), necessary equipments, tools and tackles, staging, scaffolding, etc., complete for roof, etc., including a coat of zinc chromate primer and two coats of synthetic enamel painting.

Partition Frame work made of 2" X 2" Aluminium spaced at 2'0" c/c vertically & horizontally. Additional member shall be provided at skirting, top band, grooves & at places where two different materials are combined. Necessary supports to the slab should be taken in to account. Partition panelling only with 18mm ply board The panels shall have grooves as per detail drawing finished with 1mm laminate as per design & detail. Shade and texture as per approved engineer in charge

Providing and Fixing Glass Partition (on to item no 8 or on masonry wall)using 10mm toughened glass with frosted film on frame all over aluminium frame. Design and detailing as per engineer in charge

Providing and Fixing Flush shutter door with door frame 150mm*75mm and - 32mm th. door finished with laminate and glasez pane in between on both sides.. Shutter to have 35mm wide and 12mm thick lipping beading allround finished with enamel paint of approved brand, colour and shade., Cost to include necessary hardwares door closer, hinges, etc., complete. Size 8'*4'. Above lintel level fixed glass is to be fixed .Details to be followed as per engineer in charge.

Providing & fixing in position glazed entrance door which is frameless using 12mm toughened glass with edge polish. The door to consist of floor spring , Top patch, Bottom patch, Top pivot & S.S handle . Provide Patch lock .Cost to include silicon sealant. size is 8'*4'.Above lintel level fixed glass is to be fixed.The door shall be finished with privacy film.

Providing & fixing calcium silicate ceiling tiles of size 595 x 595 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanised steel sections ( galvanized @ 170 gsm/sqm.) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet spaced at 1200mm center to center and cross “T” of size 24x25mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main “T” at 600mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600mm and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 21x21x0.30 mm and laying false ceiling tiles of approved texture in the grid including, wherever, required, cutting/ making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats fixed to ceiling with 6 mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanised level clips spaced at 1200mm center to center along main‘T’ bottom exposed with 24mm of all T sections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawing and as directed by engineer-in-charge.8 mm thick

Providing and fixing False Ceiling as per India Gypsum Specifications made of standard G.I. Sections and 12.5mm thick gyp board sheets inclusive of all hangers, edge members and other clips complete, with sheets fixed with proper screws by power drills and joints duly finished ensuring level in line and plumb to take final paint. All inclusive of detailed cut-outs for light fixtures, AC grilles. All Vertical drops will be measured extra as per actuals.The cost to be inclusive of surface preparation as per INDIA GUPSUM STANDARDS ( MODE OF MEASUREMENT L x B) .

Providing & laying flooring,skirtring of vitrified tile over a bed mortar of 20 mm thk in CM 1:5 or chemical laying as per the instruction of engineer incharge, including slurry, having joints filled with cement of matching color including washing, cleaning etc tiles will be laid with 2 mm gap using spacers and gap will be filled with epoxy grouting complete as per specifications. Necessary protective covering to prevent damage for the finish flooring to be given 300 microns plastic sheet and POP spread over it at no extra cost and to be retained until handover size:600*600.

Providing & fixing 300mmx300mm & 6mm thk. anti skid ceramic tile flooring of approved size set in 12mm thick CM 1:3, with cement slurry, pointing of tiles with Tilemate or equivalent to match the colour of the tiles, Proper slope to be maintiained, curing ,oxalic acid wash etc., complete. no extra charge payable for cutting borders, cutting for drain holes etc.)

Providing and dadoing 300mmx450mm with vitrified tile on a backing plaster of CM 1:4 including slurry,12 mm thick including pointing with matching Cement grout , including acid washing, complete as per specifications and as per the sizes and pattern given by engineers. Rate to include cost of all materials and labour required for the finished job.

Providing and laying 14mmthk FSC certified laminated wooden flooring of size 125mmx1850mm. The planks shall be provided with tongue & groove required for locking. The flooring to be layed with 5mm underlay foam and 60 microns LDF film placed over it as moisture barrier to proper level with necessary edge profile & transition strip where ever necessary complete as per manufacturers instructions. The rate shall include cost and conveyance of all materials,labor charges,lead,lift,laying Self leveling screed 3-5mm thk etc. all complete as specified and as directed by the Engineer-in-Charge

Providing and Laying Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, making of lines or groove etc complete but excluding the cost of nosing of steps etc. complete. 75mm thick with 20mm thick nominal size aggregate.

Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. Green / Black / Other granite : Above 3601 Cm2 Slabs

Providing and applying acrylic emulsion paint finish to walls, blocked partitions, and plasterboard ceiling surfaces of approved shade, texture. Existing wall and ceiling surfaces to be prepared by scraping away any loose particles, dust, etc by washing and scrubbing and 1 coat of primer approved by manufacturer applied. The wall surfaces are then smoothened using putty approved by the manufacturers. Surfaces are then sandpapered to achieve a smooth finish and two or more coats of paint are applied as per manufacturer's specification.

Providing and Painting (two or more coats) on door and windows with synthetic enamel/Enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on new work. Colour to be taken approval from engineer-in-charge

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) first layer of slurry of cement @ 0.488 kg/sqm mixed with water proffing cement compound @0.253 kg//sqm .This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proffing cement compound @ 0.126 kg/sqm This layer will be allowed to air cure for 4 hours followed by water curing for 48 hours. The rates includes preparation of surface treatment & sealing of all joints ,corners, junction with polymer mixed slurry.

Providing and fixing superior quality PVC Tank Cover complete as per approved by Engineer-in-charge In Charge: 500ltr

Providing and Making khurras 45*45 cm with minimum 5cm thick cement concerete 1:2:4 over PVC sheet,finised with 12 mm cement plaster1:3 and a floating coat of cement.

Providing the work of Diamond cutting of stone wall 380 mm thick and disposing off debris outside the campus with lead of 5 kms.

Providing and Fixing Counter for hardware room: Includes half brick masonry work with plaster for partition wall up to the height of 770mm for counter of (length x breath) 3600mmx600mm. The counter slab work includes stone slab with top polished & moulded granite work.

Furniture

Supply & Installation of 2 Seater Sofa The seat should be made of PU foam with Density 32 ± 2 kg/cu.mtr having an additional top layer of J PU foam with Density 28 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 23±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure: should be made up of 1.2±0.1 cm. thick hot pressed plywood . Dia 4mm zigzag spring assembly should be mounted in understructure for support and additional cushioning purpose .it should be a welded assembly made in Stainless steel (grade SS 202) tube & plate. as per 3D view matching with Photographs as attached in RFP

Supply & Installation of chair with headrest for 1 Person SEAT/BACK ASSEMBLY: The Cushioned seat assembly should be consists of seat outer (material-30% Glass Fiber Nylon)& upholstered Seat inner (material- Poly Propylene) with moulded Polyurethane foam & polyster fabric. The Net Back should be made up of Back outer (material-Glass Fiber Filled Nylon)& Back inner (material- PP) and upholstered using Polyester Mesh fabric with high tenacity yarn. Full Back Size: 46.5 cm. (W) x 60.0 cm. (H) Seat Size : 51.0 cm. (W) x 49.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density = 45 +/- 2 kg/m³ and Hardness load 12 +/- 2 kgf for 25% compression. BACK SPINE: The support spine should be made up of High Pressure Die cast polished hed Aluminum. ARMRESTS : The armrest should be having two adjustment, Height (6.0±0.5cm) and Depth (6.0±0.5cm). Height adjustment should be provided in Aluminum structure of armrest which should be connected to Aluminum Back spine and should be operated by button. The depth adjustment should be provided in pad which should be fixed to armrest structure. Armrest Top should be made up of PU molded over plastic inner.ACTIVE BIO-SYNCHRO mechanism: The adjustable tilting mechanism should be designed with the following features: • 360° revolving type • Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort • Tilt tension adjustment can be operated in seating position • 5 position Tilt limiter giving option of variable tilt angle to the chair • Seat / back tilting ratio of 1:2 • The mechanism housing should be made up of HPDC Aluminum & black powder coated (DFT 40 to 60 micron)SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 3.75±0.1 cmLUMBAR SUPPORT ASSEMBLY: The Lumbar support assembly should consist of lumbar spine (material-Glass Fiber Filled Nylon) which should be fixed to Aluminum Back spine. The Lumbar pad (material- Poly Propylene) should be fixed to lumbar spine through lumbar Pad support. Lumbar Support Assembly has height adjustment of 5.0±0.5cm PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3cm. PEDESTAL ASSEMBLY WITH CASTORS:The pedestal should be High Pressure Die cast polished Aluminum and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.) TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black PP having 6.0± 0.1cm wheel Diameter..The neckrest assembly consshould be ts of upholstered Neckrest inner(material-PolyPropylene) with moulded Polyurethane foam and Polyster fabric.Upholstered inner should be fixed to Neckrest cover.Neckrest should be fixed to Back assembly through Neckrest spine .Neckrest assembly has height adjustment of 5.5 +/- 0.5cm and Rotation adjustment of overall 20° +/- 2° as per 3D view matching with Photographs as attached in RFP

Supply & Installation of Chair without headrest SEAT/BACK ASSEMBLY: The Cushioned seat assembly consshould be ts of seat outer (material-30% Glass Fiber Nylon)& upholstered Seat inner (material- Poly Propylene) with moulded Polyurethane foam & polyster fabric. The Net Back should be made up of Back outer (material-Glass Fiber Filled Nylon)& Back inner (material- PP) and upholstered using Polyester Mesh fabric with high tenacity yarn. Full Back Size: 46.5 cm. (W) x 60.0 cm. (H) Seat Size : 51.0 cm. (W) x 49.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density = 45 +/- 2 kg/m³ and Hardness load 12 +/- 2 kgf for 25% compression. BACK SPINE: The support spine should be made up of High Pressure Die cast polished hed Aluminum. ARMRESTS : The armrest should be having two adjustment, Height (6.0±0.5cm) and Depth (6.0±0.5cm). Height adjustment should be provided in Aluminum structure of armrest which should be connected to Aluminum Back spine and should be operated by button. The depth adjustment should be provided in pad which should be fixed to armrest structure. Armrest Top should be made up of PU molded over plastic inner. ACTIVE BIO-SYNCHRO mechanism: The adjustable tilting mechanism should be designed with the following features: • 360° revolving type • Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort • Tilt tension adjustment can be operated in seating position • 5 position Tilt limiter giving option of variable tilt angle to the chair • Seat / back tilting ratio of 1:2 • The mechanism housing should be made up of HPDC Aluminum & black powder coated (DFT 40 to 60 micron) SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 3.75±0.1 cm LUMBAR SUPPORT ASSEMBLY: The Lumbar support assembly should consist of lumbar spine (material-Glass Fiber Filled Nylon) which should be fixed to Aluminum Back spine. The Lumbar pad (material- Poly Propylene) should be fixed to lumbar spine through lumbar Pad support. Lumbar Support Assembly has height adjustmentof 5.0±0.5cmPNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3cm.PEDESTAL ASSEMBLY WITH CASTORS:The pedestal should be High Pressure Die cast polished Aluminum and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.)TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black PP having 6.0± 0.1cm wheel Diameter. as per 3D view matching with Photographs as attached in RFP

Supply & Installation of Reception Table 1850x750x1100 (l*b*h) Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire management Secondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Drawer under counter in fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Drawer extension should be 325 MM. Drawers should have a soft closing & anti slam mechanism. Handles should be provided for ease of opening. Pedestals should be provided with lock for security. Provision for 3 set of 5/15 AMP Switch/Sockets along with 1 no. LAN Sockets should also be there including supply & provision of connector for Laptop connectivity. as per 3D view matching with Photographs as attached in RFP

Supply & Installation of Manager Table 1250x750x770 (l*b*h) Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire management.Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Integrated Pedestal Made of 25mm. Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedestal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension should be 325 MM. Drawers should have a soft closing & anti slam mechanism. Handles should be provided for ease of opening. Pedestals should be provided with lock for security. Providing and supplying for 3 set of 5/15 AMP Switch/Sockets along with 1 no. LAN Sockets should also be there including supply & provision of connector for Laptop connectivity. as per 3D view matching with Photographs as attached in RFP

Supply & installation of Manual Roller blinds having Aluminum Roller tube along with fabric pasted on it with glue having control unit for manual operations and bottom bar Aluminum powder coated for weight purpose, including fabric, fitting & accessories of approved make & colour etc. complete.

Supply and Installation of Conference Table size 10'*4' table and 30" height with laminate finish and leg to be box section MS powder coated. Design and detailing to be engineer in charge.Provision and supply for 3 set of 5/15 AMP Switch/Sockets along with 1 no. LAN Sockets should also be there including supply & provision of connector for Laptop connectivity.

Supply and Installation of credenza: structure made up of 18 mm thick Prelaminated partricle board with 2mm thick PVC edge banding tape.Approx. dimension 1200(w)*450(D)*1200(H).

Providing and fixing soft boards , without any frame work and beading and with including providing and fixing fabric of approved make and colour etc., all as per drawing & engineer's instructions.

Providing and fixing graffitie (hand paint Modern abstract)Design and detailing as per engineer in charge. Please refer reference image

Ceramic writing board with 25 X 40 beechwood/ approved beading on 12mm ply - size 2400 x 1200

Providing and fixing hoardings outside the building as per size give by engineer in chargeApprox. Dimensions:1200mm(W) X 900mm(H) with provision of backlight.

Providing and fixing of in reception made up of laser cut Anti-Corrosive high grade AISI 316 Stainless Steel size 1mtr by 1mtr .details given by engineer in charge.

Providing and fixing Name plate for individual cabin and rest of the area. Signage's are made up of laser cut Anti-Corrosive high grade AISI 316 Stainless Steel of 2mm thick sheet with laser cut method for impression and with satin finish. Approx. Dimensions: 300 mm X 170 mm X 2 mm.Design and detailing provided by as per engineer in charge

Electrical ( supply and fixing of following items)

Wiring of light point/ fan point/ exhaust fan point/ call bell point as per specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit & it's all accessories( J.B. , Bends etc.) , round tiles,18 SWG Hot Dipped Galvanized Modular Box with earth terminal, 6 A Modular switch, Modular face plate with grid plate, 3 pin ceiling rose / lamp Holder/ 3 pin connector , screws etc, making connections,all as per pre approved by Engineer in charge, testing etc. complete as required as per recommended makes of RFP.

Short point (up to 3 mtr.)

Medium point (up to 6 mtr.)

Long point (up to 10 mtr..)

Wiring of 3/5 pin 6 amp. Light plug point as per specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit & it's all accessories( J.B. , Bends etc.) , round tiles, 18 SWG Hot Dipped Galvanized Modular Box with earth terminal, 6 A modular switch, 3/ 5 pin 6 A modular socket, Modular face plate with grid plate, screws etc,all as per pre approved by Engineer in charge, making connections, testing etc. complete as required as per recommended makes of RFP .

On board

Short point (up to 3 mtr.)

Medium point (up to 6 mtr.)

Long point (up to 10 mtr..)

P & F 3 Way, 4 Conductors with current rating 16 Amp. Connector

S&F following sizes of ISI marked DLP U-PVC mini trunking systems along with accessories like end cap, internal angle, external angle ,Flat angle, Flat junction etc. on surface with screws, expansion fasteners as required. (make: legrand)

Mini-Trunking -32 x 12 mm

Finishing Accessories

End cap right or left

Changeable internal-external angle from 600 to 1200

Changeable flat angle from 850 to 950

Flat junction

White 32 x 10/12.5 cover joint

S&F following sizes (dia.) of ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit as per specification for electrical Works along with its accessories (IS: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required as per recommended makes of RFP .

Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4, , in existing surface or recessed PVC/ MS conduit/casing capping including all as per pre approved by Engineer in charge,making connections, etc. as require as per recommended makes of RFP.

3x 1.5 sq.mm

2 x 2.5 sq. mm. + 1x1.5sqmm

2 x 4.0 sq. mm. + 1 x 2.5 sq. mm.

2 x 6.0 sq. mm. + 1 x 2.5 sq. mm.

4 x 10.0 sq.mm

Supplying and fixing of power plug point with Modular accessories as per specification for electrical Works, on hot dipped galvanized modular box of 18 SWG with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost of ISI marked modular 16 amp. Switch (IS :3854) and 3/5 pin 16 amp. socket outlet (IS:1293) , making connection , testing , etc. as required. All as per pre approved by Engineer in charge, as per recommended makes of RFP.

Providing & Fixing of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load and site requirement) 4KV impulse withstand voltage, as per specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , IP 20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A rating including making connections, testing etc. as required. . All as per pre approved by Engineer in charge, as per recommended makes of RFP .

Single pole MCB

6 A to 32 A rating

Double pole MCB

40 A to 63 A rating

Four pole MCB

40 A rating

50-63 A rating

Providing & Fixing of 240/415 V Residual current circuit breaker (RCCB) as per specification for electrical Works with ISI marked (IS:12640-1) / conforming to IEC 61008 -1 , rated conditional s/c current of 10 KA, truly current operated and shall operate on CBCT mechanisum, provision for pad lock, min. operation 10,000 upto 63 A rating and 5000 for 100 A rating, minimum phase termination capacity of 50 sq.mm. rigid wire , IP 20 contact protection with existing distribution board / sheet including making connections, testing etc. as required. & All as per pre approved by Engineer in charge, as per recommended makes of RFP .

Two pole 100/300mA sensitivity

40 A rating

Four pole 100/300 mA sensitivity

40 A rating

63 A rating

SITC of wall/ free standing floor mounted dust and vermin proof compartmentalised cubical panel as per specification for electrical Works, made out of CRCA sheet . Other parameters required as per point (a) ,(b), (c),(d) below:- (a)Thickness of sheet shall not be less than 1.6 mm up to 600 mm length / width of any compartment and be of 2.0 mm above 600 mm. Load bearing structure shall be of 2.0 mm thick sheet supported by base M.S. channel if required . Side walls and cable alley compartments having bolted type doors with / without detachable extension type structure (b)panel shall be duly treated for derusting in 7 tank process with dephosphating and with powder coating of minimum 70 microns on both side of panel in desired shade The panel having PU/ Neoprene rubber gasket of not less than 3mm thickness ,required hardware, separate detachable gland plate M.S. base channel (min75mm) , hinged door with locking arrangement for equipment/switchgear [c) Interconnection between bus bar and switchgears /cable shall be rigidly supported and made out by flexible copper wires (up to 125 amp ) and by solid bus bar (>125 amp ) . All joints / interconnections of copper bus bar shall be dully tinned . Clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar Bus bar is insulated by Heat Shrinkable sleeves . Earth and Neutral bus bar shall be half of the size of phase bus bar. (d) only outer area on all sides shall be measured & panel to be fabricated only from CPRI approved fabricator. All as per drawing pre approved by Engineer in charge. as per recommended makes of RFP .

Supplying and fixing of Aluminium (IEC 60105 ISO 209-1,2) / Copper (IEC 60028) bus bar as per specification for electrical Works, by means of SMC / DMC type insulator, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable PVC sleeves. All as per pre approved by Engineer in charge and as per recommended makes of RFP .

Electrolytic grade Aluminium bus bar 6010 grade

Providing & Fixing of BIS approved Current Transformer as per specification for electrical Works ,ISI marked as per IS 2705-1992/ conforming to IEC 60044-1, with secondary terminal of CT shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as required Current transformer Resin Cast Wound Primary / Ring Type Tape Wound as per IS 16227 with, Accuracy Cl, CT ratio and burden as specified. ISF<=5, Cu cross section of secondary wire 1.5sqmm (minimum), including all necessary support in existing panel including connection etc. as required . All as per pre approved by Engineer in charge

C T Class 1, Ratio upto 150/5, Burden 5 VA

Providing & Fixing of ISO certified company made UL listed , IP 65 110/220 V, unibody LED Indicating lamp IEC 60947 , CSA 22.2 with integral circuit, IP 20 terminal block, Approx. body dia for panel not less then 20 mm, length min. 50mm, front LED cover dia min. 29 mm, contact material phospher bronze for Led, PCB contacts shall be of brass (tin plated), impulse dielectric tested for 2.5 KV, Rated insulation resistance shall be 100 M ohm at 500VDC including connection etc. as required. All as per pre approved by Engineer in charge and as per recommended makes of RFP

Red/yellow/Green colour

Providing & Fixing of IP 51 Multi function meter as per specification for electrical Works, ISI marked (IS 16444)/ Confirming to IEC 61557 & IEC 62052 with LCD/ LED 3/4 line display capable of measuring electrical parameters like V, I, F, PF, KW, Kva, Kvar, Kwh, Kvah, Kvarh display with 1A/5A CT input for LV/ HV network, with /without RS 485 communication port etc. . All as per pre approved by Engineer in charge and as per recommended makes of RFP

Multifunction LCD meter with V, I, F, PF, KW, Kva, Kvar, Kwh, Kvah, Kvarh, Run hours, On hours, Phase angle, Interrupts, THD, Events, Neutral Current class 1 accuracy with RS485 port.

Providing & Fixing of recessed/surface mounting heavy duty sheet steel 1.6 mm thick End Box as per specification for electrical Works for distribution board duly phophatised powder coated complete as required. All as per pre approved by Engineer in charge and as per recommended makes of RFP

For TPN 4 Way

For TPN 6 Way

For SPN 12 Way

Providing & Fixing of following modular accessories as per specification for electrical Works, made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , minimum width of 1 module switch toggle( PUSH PART ) should not less then 20mm, including all as per pre approved by Engineer in charge,making connections, testing etc. as required. All as per pre approved by Engineer in charge and as per recommended makes of RFP

Blanking plate

Providing & Fixing of ISO certified company made vergin material PVC trunking system as per specification for electrical Works, with double lock feature for cable management including finishing accessories like corners, tee, adjustable angles, junction etc. as required . The trunking system shall have adaptable system for modular type RJ 45 data socket/ wiring accessories/ power sockets and shall be covered with peal off plastic cover. All as per pre approved by Engineer in charge and as per recommended makes of RFP

80mm x 50mm

SITC of chemical Gel earthing system of Dual Pipe Technology made of with "B" Class G I Pipe as per IS 1239 ( part-1):2004 of Medium duty of following sizes as per points mentioned (a), (b), [c), (d), (e) below :- (a) filled with anti corrosive conductive compounds with the permanent sealings at both the ends, CPRI/ ERDA tested with RMS capacity of minimum 35- 40 KA for withstanding 1 second . (b) To ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 Kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. The compound shall be tested form NABL acredeated lab for low resistivity ( less than 0.12 Ohm - meter) & high conductivity in nature with carbon as a major content as per referance of IS 3043-1987,IEEE 80-2013 (clause 14.5d) , IEEE 837 & IER 1956 with latest amendemnts ©Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. (d) Testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book. (e) All as per pre approved by Engineer in charge as per recommended makes of RFP

With Pipe in Pipe Technology (Outer pipe dia. / Inner pipe dia. ) Minimum 100 mm dia borewell

GI pipe 3000 mm long, 80 / 50 mm, Terminal 50 mm x 6 mm GI Strip

Supply & Laying following size earth strip in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, Jointing shall be done by overlapping and with 2 set of Brass (for Cu strip) / GI (for GI Strip) nut bolt & spring washer spaced at 50cm making connection etc. as required. All as per pre approved by Engineer in charge and as per recommended makes of RFP

25mm x 3mm copper strip

Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with GI/Cu thimble etc. as required. All as per pre approved by Engineer in charge as per recommended makes of RFP

8 SWG copper Wire

Supply & fabrication steel structure with MS channel / angle / joist / ISMB / sheet etc. including welding, rivetting, cutting, nut & bolt , one coat of primer & two coat of enamel paint etc. as required complete in all respect. All as per pre approved by Engineer in charge and as per recommended makes of RFP .

SITC of IP 40 quick make and quick break 4 pole current limiting Moulded case circuit breaker (MCCB) made of flame retardent & heat resistant material having following current rating, short circuit breaking capacity at 440/415 V, 50 Hz; O/L & S/C settings as per specification for electrical Works, conforming to IS/IEC 60947 P -2 :2003 with front face and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push (test) to trip, trip time less then 10 ms under s/c condition, Breaking capacity Ics = 100% Icu. U imp =8 KV, rated insulation voltage 800 V, provision for UVR , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connections with lugs & spreaders, etc. as required. as per recommended makes of RFP .

up to 100 Amp , 25 kA, adjustable O/L & fixed S/C setting, Ics = 100 % Icu With Thermal Magnetic release

Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-armoured / Armoured aluminium cable of 1.1 KV grade as per specification for electrical Works in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points (a), (b), (c), mentioned below:- (a) Material :- H4- Grade aluminium conductor of purity >99.6 % & as per IS:1554 P-I / IS :7098 P - I (b) conductor shall have electrolytic aluminium confirming to IS 8130, IS 3975-1999 for armouring of cables in armoured cable items , IS 5831 for sheath, IS 10810 (Part 0 to 64 ) for testing procedures . (c) All above as per pre approved by Engineer in charge and as per recommended makes of RFP .

Armoured Cable

Supplying and making one end termination with heavy duty brass compression gland (as per IS 12943- 1990) SIBG type, heavy duty aluminium lugs (as per IS 8309 -1993 & IS 8337-1976 ) duly crimped with crimping tool, PVC tape as per specification for electrical Works etc for following size of Armoured PVC insulated & PVC sheathed/ XLPE aluminium conductor cable of 1100 volt grade as required of size. All as per pre approved by Engineer in chargeas per recommended makes of RFP .

4 x 16.0 sq.mm

3.5 x 35.0 sq.mm

Providing & Fixing of IP40 LED Surface/ Recessed / suspended mounting Mid power SMD type LED Light fixture made from CRCA sheet steel housing, high purity / transmisivity UV stabilized Non -yellowish diffuser for uniform light distribution. High efficiency with 2.5 KV internal/external surge protection BIS certified isolated driver having efficiency > 85% , with Short & Open circuit protection and in compliance to IEC standards (Integral with light fixture). System lumen efficacy of ≥ 120 lm/Watt ,THD < 10 % , p.f.≥0.95,CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. All as per pre approved by engineer in charge .As per recommended makes of RFP

48W LED light fixture 2'x2' with acrylic / prismatic front cover.

Providing & Fixing of IP40 LED Recessed / Surface Mounted, Round / Sqaure Non-Dimmable Back lit SMD Mid Power LED Downlight with die-cast aluminum housing & Heat Sink for heat dissipation with UV Stabilized non yellowish Diffuser with internal/ external BIS complience 2.5 KV surge protected Isolated driver, with Short & Open circuit protection, having efficiency > 85% and in compliance to IEC standards. System Lumen efficacy of ≥ 120 lm / watt, THD < 10 % ,p.f.≥0.95, CRI >80, life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. All as per pre approved by engineer in charge .As per recommended makes of RFP

Recessed Mounting

LED Downlight 18/20W

Supply & Laying following size' B ' class , Medium class G.I. Pipe confirming to IS : 1239 P - 1 ( 2004 ) with accessories like bend, socket etc. for laying earth conductor/ strip / cable in ground/ surface/ recess as required. All as per pre approved by Engineer in charge. All as per pre approved by engineer in charge .As per recommended makes of RFP

32mm dia

Providing & Fixing of Heavy duty capacitor start, copper woind Double ball bearing 900/1400 RPM single phase Exhaust fan as per specification for electrical Works, conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as required. All as per pre approved by Engineer in charge. .As per recommended makes of RFP

300 mm sweep(900/1400 RPM)

Supply, Fabricating & installing following sizes of powder coated perforated M.S. cable trays with perforation not more then 17.5% in convenient section including horizontal and vertical bends, reducers tees,cross members and other accessories as required and duly suspended from the ceiling with MS suspenders including bolts & nuts , fastners, supports, painting suspenders etc. as required. All as per pre approved by Engineer in charge. .As per recommended makes of RFP

150mm x 50mm x 1.6mm

Supply & Fixing of ABC Type (MAP 50) type powder Fire Extinguisher (Stored Pressure type) of following capacity duly current and valid BIS certification conforming to IS: 15683:2006, with Dry chemical powder used as extinguishing agent should be Mono Ammonium Phosphate 50% concentration conforming to IS 14609:1999. Serial no. and date of manufacturing should be embossed or printed on the body of the fire extinguisher. . All as per pre approved by Engineer in charge.as per recommended makes of RFP .

Providing & Fixing of of M.S. J- hook of standard design made out of 16 mm dia. M.S. round bar and fixed with cement concrete mortar with required support as required.

Providing & Fixing of ISO Certified company made BEE Approved copper wounded 1200 mm sweep BLDC technology power saving ceiling fan with longer life span and low maintenance 5 star rated which can withstand on votage fluctuations from 140 volts to 240 volts ,power factor not less then 0.9 , service value (CMM/W) minimun 6.85 , air delivery minimun 215 CMM, speed 350 RPM ( tolerance as per IS:374 2019 ) THD less then 10% and complete with down rod up to 30 cm with secondary support safety cable , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge.as per recommended makes of RFP .

Without Remote

Providing & Fixing of heavy duty, copper wound , Double ball bearing and with metal sturdy mesh guard; Aluminium alloy one piece blade wall mounting oscillating type air circulator as per specification for electrical Works, conforming to IS:2997, including fixing with anchor bolts, regulator making connection testing etc. as required. All as per pre approved by Engineer in charge. .As per recommended makes of RFP

450 mm sweep With wall Mounting and three speed regulator

SITC of raceway confirming to EN 50 085-2-2, IP-20, IK-08 for distributing cablling for screed floora installation & particularly suitable for applications requiring EMC screening material/GI raceways made up of pregalvanized sheet (DX51D-Z120 MAC) in desired color, non corrosive, non flame propagation, with 2 to 2.5 mtr, standard length/standard depth 25mm / 38mm, thickness 1.6 mm for raceways, 1.0 mm for partition with coupler for joining raceways including making jhiris on floors/wall if required of following sizes. Make: legrand / MK

SITC of GI junction box with removable precuts knockouts provided for raceways resistance to vertical load over a small area, 500N and for large surface area 2000N with adjustable height 50 to 70mm with flyover as required . Make: legrand/MK

SITC of 10 KVA 3 Phase Input, 1 Phase Output advance DSP controlled UPS with IGBT based rectifier, LCD display, double conversion / Digital Signal Processing UPS, with isolation transformer, with 30 minute battery back up, with required cabling for incoming & outgoing connection (Approved makes: Emerson / Numeric / APC/Delta)

Technical Specification: Phase: 3 Pahse in /1 Phase out Capacity : 10000 VA /9000 W Input Characteristics : Nominal Voltage : 3 X 400 VAC (3 Ph +N) Voltage Range: 305-478 VAC(3-Phase) @ 100% Load Frequency Range: 46~54 Hz or 56~64 Hz Power Factor - >= 0.99 @ 100% Load THDi : < 6% @ 100 % load

OUTPUT Characteristics : Output Voltage : 208/220/230/240 VAC AC Voltage Regulation (Batt, Mode) : ± 1 % Frequency Range (Synchronized Range) : 46~54 Hz or 56~64 Hz Frequency Range (Batt. Mode) : 50 Hz ± 0.1 Hz or 60 Hz ± 0.1 Hz Current Crest Ratio : 3:1 (max.) Harmonic Distortion : ≤ 2% THD(Linear Load) ; ≤ 5 % THD (Non- Linear Load) Transfer Time (AC Mode to Battery Mode): Zero Transfer Time (Inverter to Bypass) :Zero Waveform (Batt. Mode) : Pure Sinewave AC mode Efficiency : ˃ 92% ECO Mode Efficiency : 97 %

BATTERY Characteristics : Battery Type : SMF or Tubular Battery Nos. : 20 Charging Current (Max.) : 12 A settable to 2/4/6/8/10/12 Amps Charging Voltage: 273 VDC ± 1 % (Based on 20 pcs batteries)

Indicators: LCD Panel : UPS status , Load level, Battery level, input/output voltage, Discharge Timer and Fault Conditions

Alarm: Battery Mode : Sounding every 4 seconds Low Battry : sounding every second Overload : sounding twice every second Fault : continuously sounding

10 KVA 3 Phase Input, 1 Phase Output

LAN Services:

Supply , Installation, Testing and Comissioning of Wall mounted Communication rack with glass doors, handles ,lock , Top and Bottom Cable entries, Supports for mounting rack on wall , Cable managers, one Fan, Equipment mounting hardware, power supply box for supplying power to switches, fans etc along with earth continuity kit, Mcb, indicator, moulded power supply cable

12 U(44 mm ) wall mounted

Supply, Installation, & Testing of 19" 1U Rack Mounted/ surface mounted aluminum/ CRCA 1.2mm powder coated, multimode glass Fiber Optic Cable Patch panel/LIU loaded with flangless/screwable adapters for ST/E-2000/SC/LC/MT-RJ/PC type, It should have easy removable Top plate with push buttons, there should be a splice tray installed in the Patch panel/LIU which can handle the fiber cores, splice tray should be PC+ABS material, it should include accessories like mounting hardware, gormetts, heat shrink tubes/sleevs, screws, nuts to install the panel for rack/wallmount applications as per requirement complete in all respect. All as per pre approved by Engineer in charge and as per recommended makes of RFP .

Multi Mode LIU 6 Ports

Supply, Installation, & Testing of Indoor duplex Multimode patch cord (50/125 µm made of glass fiber optic with LSZH jacket, Multimode G652.D Mounted on both sides with ST/E-2000/SC/LC/MT-RJ/PC type Duplex connectors in acc. with IEC 61754-20 as per latest ammendments of TIA/EIA 569B.3, as per requirements complete in all respect. All as per pre approved by Engineer in charge and as per recommended makes of RFP

Supply, Installation, OTDR Testing & Fusion Splicing of Fiber Multimode Pigtail (50/125 µm) made of glass fiber optic, should be fitted at one end with any one type of single ST/E-2000/SC/LC/MT-RJ/PC type connector in acc. with IEC 61754-20, as per latest ammendments of TIA/EIA 569 Standard Specification as per requirments complete in all respect. All as per pre approved by Engineer in charge. .As per recommended makes of RFP

Supply, Drawing and Testing, of stranded Multi mode (50/125 µm) glass optic fiber cable, as per latest ammendments of TIA/EIA 568/ISO/IEC 11801:2011/ IEC 60794-1-2 E1, E3,E11, F1/ EN 50173-1/ EN 187 000/ IEC 60974-2, 2-20, 2-21/ ITU G.652D, construction of LSZH outer sheath cable, cable should be used for LAN and WAN back bones, . With its LSZH sheathing these cables should be ideal for indoor/outdoor installations in existing MS/PVC /HDPE Conduits/ slotted channels with ferruling at both ends for identification complete in all respect. All as per pre approved by Engineer in charge. .As per recommended makes of RFP

6 core 10G optic fiber cable

Supply , Installation and Testing of 4 pair, 100 Ohm impedance, Cat 6/6A patch cords should be constructed of minimum 23/24 AWG, stranded bare Copper cable with FRPVC/LSZH Jacket, with an enhanced performance by factory moulded RJ45 connectors as per ANSI/TIA/EIA 568 suitable for Cat 6/6A application complying to latest ammendments Category 6/6A Standards, According. to TIA568, minimum requirement for 1G BASE-T/ 10G BASE-T performance. Patch cords shall be straight thru cable compatible with both T568-A and T568-B wiring schemes, Minimum 750 to 1000 mating cycles in plug contacts for long durability complete in all respect. All as per pre approved by Engineer in charge. As per recommended makes of RFP

Cat 6, UTP (Un-sheilded Twisted Pair) Patch Cord

Supply, Installation, Testing and Comissioning of Rack mounted 19" 1U, 24 Port Unloaded, 1.5-1.6 MM CRS chasis, powder coated, sheet steel, made of plastic (ABS), Modular Patch Panels (without I.O.) with Rear Cable management system and mounting hardware to mount the patch panel. Should have port identification numbers printed/engraved on front of the panel, . There should be a provision for each port/jack on the panel and reusable removable on field from the panel complete in all respect. All as per pre approved by Engineer in charge and as per recommended makes of RFP

SITC of Intelligent Ethernet POE Switches providing 24 x 10/100/1000 Fast Ethernet POE ports- 370W or better and 4 dual purpose uplink (provision for Copper / Fiber Giga connectivity) with provision of minimum Stacking of 06 Switches with related LAN Base Software . For additional technical parameters of products/ work as per recommended makes of RFP.

Supply, Installation, Testing and Comissioning of Rack mounted , 48 x 10/100/1000 Ethernet ports Gigabit Switch with 4 mini Gigabit Interface Converter slots(shared with 4 Ethernet ports) for Gigabit Ethernet expansion , Switching capacity 96 Gbps nonblocking , . As per recommended makes of RFP.

Supply, Installation, Testing and Comissioning of 1G SFP (small form-factor pluggable) transceivers as per recommended makes of RFP.

Supply, Installation, Testing and Comissioning of 10G SFP (small form-factor pluggable) transceivers as per recommended makes of RFP.

Supply, Drawing and Testing of 4 pair, 23 AWG Solid Bare Copper wire insulated with PVC, UTP (Unshielded Twisted Pair), Category 6, Class E, 100 Ohm Impedance, Indoor Cable as per latest ammendments of ANSI/TIA/EIA-568 , The copper conductors should be balanced twisted in pairs, seperated by a cross-member fluted pair divider & protected by PVC Jacket. Certified performance in a 4-connector configuration upto 100 Mtrs channel requirements & transmission frequencies up to 250 Mhz. in existing MS/PVC Conduits/casing capping including making connections to Information outlets and Patch Panels with jack & ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. All as per pre approved by Engineer in charge and as per recommended makes of RFP

Supply and Installation of unsheilded/ sheilded Information outlets made of high impact plastic body with ABS, FR Grade with provision for protection against dust in jack/ FP, suitable for Cat 6/6A application complying to latest ammendments, According. to Cat. 6/6A channel, It should support channel as well as components requirements of Cat.6/6A standards at frequencies of up to 250 to 500 Mhz. Cat 6/6A unshielded/shielded Jack should be suitable to terminate 4 pair, 23/24 AWG solid/stranded wire diameters, using 100 Ohm unshielded/shielded balance twisted pair cable, the jack should have tooless/impact punch termination on reliable copper tin plated Insulation displacement contact, It complied with ANSI/TIA/EIA 568 standard. In existing modular/MS Boxes along with necessory connections as required complete in all respect. All as per pre approved by Engineer in charge and as per recommended makes of RFP

Cat 6, Un-sheilded Information Outlet

Supply & fixing of square Faceplate for Flush / Surface Mount Information Outlets Single/Dual or Quad Aperture , material should be PC+ABS body, Suitable for RJ45 unshielded/shielded connection modules. Should match with I. O.. Dimensions should be 86mm X 86mm as required complete in all respect. All as per pre approved by Engineer in charge. As per recommended makes of RFP

Single Aperture

SITC of Workstation latest Intel® i5 processor, Intel Chipset motherboard, 08 GB RAM, 1 TB SATA HDD at 7200 rpm, with 4GB GPU type higher end Graphic card for H.265 compression technique with dual display ports/DVI/ HDMI port, Giga LAN Card, wireless Keyboard, wireless optical Mouse, (Approved Makes: Dell, HP, Lenevo)

SITC of 5 MP IR Fixed Dome Network Camera -1/2.7 inch Progressive Scan CMOS, 2592 × 1944 at 25fps, 2.8 mm Fixed lens, 0.003 Lux at F1.4, 0 Lux with IR on, ICR, ONVIF (PROFILE S, PROFILE G, PROFILE T), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, BLC, HLC, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 256 GB (SD card not included), IP67, IK10, Edge Analytics- Line crossing detection, Intrusion detection, Motion detection, Region entrance detection, Region exiting detection, Scene change detection, Face capture, Video tampering, audio exception detection, False alarm reduction through human and vehicle target classification based on deep learning UL, CE, FCC certified.Approved brand:- Pelco, Prama, Axis, hikvision

SITC of 32 Ch Smart Network Video Recorder : Connect Up to 32 IP Cameras, Dual OS, Up to 12 Megapixels Resolution, 2 HDMI at least 1 HDMI 4K, 2 VGA atleast 1 VGA 2MP Output , Support H.265, MJPEG, Incoming Bandwidth 320Mbps, 8 SATA Hard Disks, ANR Technology, 8 SATA interfaces for 8 HDDs and capacity of each HDD upto 6TB, 3 × USB 2.0 at least 1 USB with 3.0, Alarm I/O 16/4, RS-485, RS-232, 2 RJ-45 10 /100/1000 Mbps self-adaptive Ethernet interface,two 8 tb hardisk included, Multiple network monitoring: Web viewer, CE, FCC, UL certified.Approved brand:- Pelco, Prama, Axis, hikvision

supply and fixing Interactive Display65' with mounting kit Approved Makes:- Hikvision, samsung, Sony

Fire Services:

Supplying and drawing FRLS PVC insulated & unsheathed flexible copper conductor as per specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC 60228. FRLS PVC insulation which provides better fire retardant properties then normal PVC & also emits Low Smoke in case of fire & use type A insulation PVC, in existing conduit including , all as per pre approved by Engineer in charge,making connections, etc. as required. As per recommended makes of RFP

2 x 1.5 sq.mm

SITC Conventional Optical type Smoke Detector with mounting base, LED etc. as required.

SITC of conventional type Manual call point complete with Glass, hammer and chain etc. as required.

SITC 6 watt Speaker mounted in M S sheet box with perforated front mesh for PA and Emergency System.

SITC of wall / floor type following zone (each zone accessing minimum 20 units (detectors/ devices ) Conventional Type microprocessor based with LCD display main control panel/ floor panel fabricated from 16 SWG CRCA sheet steel sealed maintenance free (SMF) batteries of min2X7AH of 12 V or as required.

Specification: (i) Three Form-C relays (1 Fire, 1 Fault and 1 Fire/Fault 2 Amps@30VDC (ii) 1 On-board NACs operating @ 0.5 A/circuit (iii) Aux Output : 24 VDC (iv) Sounder Output : 24 VDC (v) Feature Detection Circuits: 4 Zones ( upto 20 Detectors + 5 MCPs) (vi) Zone wise Fire, Fault , Disable indication (vii)Panel keys : Silence Buzzer/ Alarm, Reset, Navigation keys (Left, Right, Down, Menu/Ok) (viii) Lamp Test & Walk Test (ix) Standby power 24V DC (2 no's of 12V, 7Ah Lead Acid Battery) (x)Certification (CE, LVDE) (xi) Event Log- 1200 events (xii) Earth fault monitoring

User Interface: Display: 16 X 2 character LCD Control Keys: Menu/Ok, Silence, Navigation and Reset buttons Indicators: Fire, Power, Fault, NAC Fault, Earth Fault, Silence

Wiring Details: Mechanical Specifications : Construction: Cold Rolled Steel with powder coated finish with door lock Cable Entry : 08 Number x 20.50 mm knockout Electrical Specifications: Operating Voltage: 230 VAC, 50 HZ Alarm Load(Sounder) 0.5 A (max) NAC output 0.5Amp.(max) Operating Temperature : 0oC~ 49oC Relative Humidity : 5 % to 95 % non -condensing Standby Batteries : Minimum capacity (2 X12 V 2.8 Ah); Maximum Capacity (2 x 12 V 7 Ah) Detection Circuits : 2,4,zone , max 2 mA per detector class B circuit External outputs : sounder output (18.5 to 28.0 Vdc, 0.5 Amp.(max)); Auxiliary Output ( 18.5 to 28.0 Vdc, 0.5 Amp.(max))

Compatible Devices: System sensor Photo Electric Smoke Detector, System sensor Photo Electric and Heat detector, System sensor Plug-in detector base System sensor MCP Red W/O Back Box System sensor Horn cum strobe , wall , Red, Standard Candela

HVAC Services

Supply, Installation, Testing and balancing of powder coated /Anodised extruded aluminium construction inlet fixed single air louvers with bird screen for Exhaust air of size upto 1.0 sqft area, Installation has been done on the Exhaust Fan of make Systemair / Ravistar / Trox/MetalJoint/Airflow or equivalent make.

SITC of Air Cooled split type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (EP foam pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 4 Mtr (IDU to ODU), R-22/R-410 Refrigerant, Remote, suitable for 400/230V +10% of 50 Hz ,1 /3 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / reciprocating / rotary compressor as specified.

Hi Wall/Ceiling Wall Split

1.0 TR with 5 star rating of BEE

1.5 TR with 5 star rating of BEE

2.0 TR with 5 star rating of BEE

SITC of Air Cooled Cassette type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (EP foam pipe section) upto 10 Mtr (IDU to ODU), copper power cable upto 10 Mtr (IDU to ODU), R-22 Refrigerant, wireless Remote, drain pump,suitable for 400/230V +10% of 50 Hz ,1 /3 phase AC supply capable of performing cooling, dehumidification, Air circulation, filteration & ventilation of following capacity with Scroll / reciprocating / rotary compressor as specified.

SITC of Interconnecting refrigerant pipe work with closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications including chase cutting, supports etc. as required.

Providing and fixing of cPVC drain water piping complete with fittings, support with MS hanger as per specification and insulated with 6 mm thick closed cell elastomeric nitrile rubber insulation. Make: cPVC Pipe -Supreme / Astral / Kisan. Insulation - Armaflex / Supreme/ Superlon / Aflex /Kflex.

32 mm dia O.D

25 mm dia O.D

Making hole in stone masonary/ RCC wall/ RCC slab with core cutter for accomodating refrigerant pipe/ drain pipe/ MS pipe/ cables etc of following dia

150 mm dia per running inch length

Water Purifier

Providing and fixing Kent or Equivalent water fountain chillar cum inbuilt RO water purifier with cooling capacity 30 Ltr per hour@ 14-22 degree C and no of faciets to be 2 (1 cold+ 1 normal)

Description of Work / Item(s)

Amount

Civil (supply and execution of following items)

Demolishing/dismentling manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material All lead and lift from site upto 5km outside the site (dispose of the material) at safe place

Brick work, Stone Masonry, Plastering, Flooring/ Dadooing /skirting/tiles all types (L.S.)

Joinery( door, window, ventilator, vent, WC, urinals, wash basin,exisiting railing & MS shutter) and handing over to local authorities (L.S.)

Providing and fixing of W.C. pan (any type including WC cover,SS jali, health Facuets,cistern 10 liters etc all accesories), Urinals and wash hand basinincluding pillar cock,angle valve,connection pipe,outlet pipe,ss jali of all sizes with care including all necessary fittings P or S trap. Cost to include if any repair of pipe work or new pipe to be installed in all manners. Toilets to be handed over in working conditions

supply and execution of Half brick masonry in Superstructure , above plinth level upto floor V level using bricks of designation 75 Cement mortar 1 : 6 (1 cement : 6 coarse sand)

Brick work with FPS briks of class designation 75 in superstructure above plinth level upto floor 5 level in all shapes and size.. In Superstructure in cement mortar 1:6 (1 cement : 6 fine sand)

Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead : With cement mortar 1 :4 ( 1 cement : 4 coarse sand)

Preparing the surface and plaster all internal RCC/ masonry surface with cement mortar 1:6, 20mm thick, smooth finished to line and plumb at all levels including all leads and lifts with necessary scaffolding, curing, hacking the surface, etc., complete.

Providing & fixing Steel work welded, in built up sections framed work including cutting, hoisting, fixing in position and with one coat primer & two coat oil paint as per detail drawings etc. complete. in columns, beams and joists, channels M.S. flat, Angles, Pipes, tees flats with connecting plates or angle cleats STRUCTURAL STEEL

supply and fixing of Partition Frame work made of 2" X 2" Aluminium spaced at 2'0" c/c vertically & horizontally. Additional member shall be provided at skirting, top band, grooves & at places where two different materials are combined. Necessary supports to the slab should be taken in to account. Partition panelling only with 18mm ply board The panels shall have grooves as per detail drawing finished with 1mm laminate as per design & detail. Shade and texture as per approved engineer in charge

supply and fixing of Glass Partition (on to item no 8 or on masonry wall)using 10mm toughened glass with frosted film on frame all over aluminium frame. Design and detailing as per engineer in charge

supply and fixing of Flush shutter door - 32mm th. finished with laminate and glasez pane in between on both sides.. Shutter to have 35mm wide and 12mm thick lipping beading allround finished with enamel paint of approved brand, colour and shade., Cost to include necessary hardwares door closer, hinges, etc., complete.Cost to include above lintel level 3.5'*4.5' window with fixed glass

supply and fixing of Flush shutter door with door frame 150mm*75mm and - 32mm th. door finished with laminate and glasez pane in between on both sides.. Shutter to have 35mm wide and 12mm thick lipping beading allround finished with enamel paint of approved brand, colour and shade., Cost to include necessary hardwares door closer, hinges, etc., complete. Size 8'*4'. Details to be followed as per engineer in charge.

Providing & fixing in position glazed entrance door which is frameless using 12mm toughened glass with edge polish. The door to consist of floor spring , Top patch, Bottom patch, Top pivot & S.S handle . Provide Patch lock .Cost to include silicon sealant. size is 8'*4'.Above lintel level fixed glass is to be fixed.The door shall be finished with privacy film.

Providing & fixing calcium silicate ceiling tiles of size 595 x 595 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanised steel sections ( galvanized @ 170 gsm/sqm.) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet spaced at 1200mm center to center and cross “T” of size 24x25mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main “T” at 600mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600mm and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 21x21x0.30 mm and laying false ceiling tiles of approved texture in the grid including, wherever, required, cutting/ making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats fixed to ceiling with 6 mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanised level clips spaced at 1200mm center to center along main‘T’ bottom exposed with 24mm of all T sections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawing and as directed by engineer-in-charge.8 mm thick

Providing and fixing False Ceiling as per India Gypsum Specifications made of standard G.I. Sections and 12.5mm thick gyp board sheets inclusive of all hangers, edge members and other clips complete, with sheets fixed with proper screws by power drills and joints duly finished ensuring level in line and plumb to take final paint. All inclusive of detailed cut-outs for light fixtures, AC grilles. All Vertical drops will be measured extra as per actuals.The cost to be inclusive of surface preparation ,3 coats of acrylic emulsion paint including the top coat as per INDIA GUPSUM STANDARDS ( MODE OF MEASUREMENT L x B) .

Providing & laying flooring,skirtring of vitrified tile over a bed mortar of 20 mm thk in CM 1:5 or chemical laying as per the instruction of engineer incharge, including slurry, having joints filled with cement of matching color including washing, cleaning etc tiles will be laid with 2 mm gap using spacers and gap will be filled with epoxy grouting complete as per specifications. Necessary protective covering to prevent damage for the finish flooring to be given 300 microns plastic sheet and POP spread over it at no extra cost and to be retained until handover size:600*600.

Providing & fixing 300mmx300mm & 6mm thk. anti skid ceramic tile flooring of approved size set in 12mm thick CM 1:3, with cement slurry, pointing of tiles with Tilemate or equivalent to match the colour of the tiles, Proper slope to be maintiained, curing ,oxalic acid wash etc., complete. no extra charge payable for cutting borders, cutting for drain holes etc.)

Providing and dadoing 300mmx450mm with vitrified tile on a backing plaster of CM 1:4 including slurry,12 mm thick including pointing with matching Cement grout , including acid washing, complete as per specifications and as per the sizes and pattern given by engineers. Rate to include cost of all materials and labour required for the finished job

Providing and laying 14mmthk FSC certified laminated wooden flooring of size 125mmx1850mm. The planks shall be provided with tongue & groove required for locking. The flooring to be layed with 5mm underlay foam and 60 microns LDF film placed over it as moisture barrier to proper level with necessary edge profile & transition strip where ever necessary complete as per manufacturers instructions. The rate shall include cost and conveyance of all materials,labor charges,lead,lift,laying Self leveling screed 3-5mm thk etc. all complete as specified and as directed by the Engineer-in-Charge

supply and fixing of Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, making of lines or groove etc complete but excluding the cost of nosing of steps etc. complete. 75mm thick with 20mm thick nominal size aggregate.

Providing and applying acrylic emulsion paint finish to walls, blocked partitions, and plasterboard ceiling surfaces of approved shade, texture. Existing wall and ceiling surfaces to be prepared by scraping away any loose particles, dust, etc by washing and scrubbing and 1 coat of primer approved by manufacturer applied. The wall surfaces are then smoothened using putty approved by the manufacturers. Surfaces are then sandpapered to achieve a smooth finish and two or more coats of paint are applied as per manufacturer's specification.

Finishing wall with water proofing cement paint of approved brand and manufacture and or required shade to give an even shade including all scaffolding: Old work (One or more coats).

Painting (two or more coats) on door and windows with synthetic enamel/Enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on new work. Colour to be taken approval from engineer in charge

Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors, urinal partition etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. Green / Black / Other granite : Above 3601 Cm2 Slabs. cost to include edge moulding

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) first layer of slurry of cement @ 0.488 kg/sqm mixed with water proffing cement compound @0.253 kg//sqm .This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proffing cement compound @ 0.126 kg/sqm This layer will be allowed to air cure for 4 hours followed by water curing for 48 hours. The rates includes preparation of surface treatment & sealing of all joints ,corners, junction with polymer mixed slurry.

Providing and fixing superior quality PVC Tank Cover complete as per approved by Engineer In Charge: 500ltr

Making khurras 45*45 cm with minimum 5cm thick cement concerete 1:2:4 over PVC sheet,finised with 12 mm cement plaster1:3 and a floating coat of cement.

Providing the work of Diamond cutting of stone wall 380 mm thick and disposing off debris outside the campus with lead of 5 kms.

supply and fixing Counter for hardware room: Includes half brick masonry work with plaster for partition wall up to the height of 770mm for counter of (length x breath) 3600mmx1200mm. The counter slab work includes stone slab with top polished & moulded granite work.

Furniture

Supply & Installation of 2 Seater Sofa The seat should be made of PU foam with Density 32 ± 2 kg/cu.mtr having an additional top layer of J PU foam with Density 28 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 23±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure: should be made up of 1.2±0.1 cm. thick hot pressed plywood 4. Dia 4mm zigzag spring assembly should be mounted in understructure for support and additional cushioning purpose .it should be a welded assembly made in Stainless steel (grade SS 202) tube & plate. as per 3D view matching with Photographs as attached in RFP

Supply & Installation of 1 Seater Sofa The seat should be made of PU foam with Density 32 ± 2 kg/cu.mtr having an additional top layer of J PU foam with Density 28 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 23±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure: should be made up of 1.2±0.1 cm. thick hot pressed plywood 4. Dia 4mm zigzag spring assembly should be mounted in understructure for support and additional cushioning purpose .it should be a welded assembly made in Stainless steel (grade SS 202) tube & plate. as per 3D view matching with Photographs as attached in RFP

Supply & Installation of chair with headrest for 1 Person SEAT/BACK ASSEMBLY: The Cushioned seat assembly consshould be ts of seat outer (material-30% Glass Fiber Nylon)& upholstered Seat inner (material- Poly Propylene) with moulded Polyurethane foam & polyster fabric. The Net Back should be made up of Back outer (material-Glass Fiber Filled Nylon)& Back inner (material- PP) and upholstered using Polyester Mesh fabric with high tenacity yarn. Full Back Size: 46.5 cm. (W) x 60.0 cm. (H) Seat Size : 51.0 cm. (W) x 49.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density = 45 +/- 2 kg/m³ and Hardness load 12 +/- 2 kgf for 25% compression. BACK SPINE: The support spine should be made up of High Pressure Die cast polished hed Aluminum. ARMRESTS : The armrest should be having two adjustment, Height (6.0±0.5cm) and Depth (6.0±0.5cm). Height adjustment should be provided in Aluminum structure of armrest which should be connected to Aluminum Back spine and should be operated by button. The depth adjustment should be provided in pad which should be fixed to armrest structure. Armrest Top should be made up of PU molded over plastic inner.ACTIVE BIO-SYNCHRO mechanism: The adjustable tilting mechanism should be designed with the following features: • 360° revolving type • Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort • Tilt tension adjustment can be operated in seating position • 5 position Tilt limiter giving option of variable tilt angle to the chair • Seat / back tilting ratio of 1:2 • The mechanism housing should be made up of HPDC Aluminum & black powder coated (DFT 40 to 60 micron)SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 3.75±0.1 cm LUMBAR SUPPORT ASSEMBLY: The Lumbar support assembly should consist of lumbar spine (material-Glass Fiber Filled Nylon) which should be fixed to Aluminum Back spine. The Lumbar pad (material- Poly Propylene) should be fixed to lumbar spine through lumbar Pad support. Lumbar Support Assembly has height adjustment of 5.0±0.5cm PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3cm. PEDESTAL ASSEMBLY WITH CASTORS:The pedestal should be High Pressure Die cast polished Aluminum and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.) TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black PP having 6.0± 0.1cm wheel Diameter..The neckrest assembly consshould be ts of upholstered Neckrest inner(material-PolyPropylene) with moulded Polyurethane foam and Polyster fabric.Upholstered inner should be fixed to Neckrest cover.Neckrest should be fixed to Back assembly through Neckrest spine .Neckrest assembly has height adjustment of 5.5 +/- 0.5cm and Rotation adjustment of overall 20° +/- 2° as per 3D view matching with Photographs as attached in RFP

Supply & Installation of Chair without headrest SEAT/BACK ASSEMBLY: The Cushioned seat assembly consshould be ts of seat outer (material-30% Glass Fiber Nylon)& upholstered Seat inner (material- Poly Propylene) with moulded Polyurethane foam & polyster fabric. The Net Back should be made up of Back outer (material-Glass Fiber Filled Nylon)& Back inner (material- PP) and upholstered using Polyester Mesh fabric with high tenacity yarn. Full Back Size: 46.5 cm. (W) x 60.0 cm. (H) Seat Size : 51.0 cm. (W) x 49.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density = 45 +/- 2 kg/m³ and Hardness load 12 +/- 2 kgf for 25% compression. BACK SPINE: The support spine should be made up of High Pressure Die cast polished hed Aluminum. ARMRESTS : The armrest should be having two adjustment, Height (6.0±0.5cm) and Depth (6.0±0.5cm). Height adjustment should be provided in Aluminum structure of armrest which should be connected to Aluminum Back spine and should be operated by button. The depth adjustment should be provided in pad which should be fixed to armrest structure. Armrest Top should be made up of PU molded over plastic inner. ACTIVE BIO-SYNCHRO mechanism: The adjustable tilting mechanism should be designed with the following features: • 360° revolving type • Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort • Tilt tension adjustment can be operated in seating position • 5 position Tilt limiter giving option of variable tilt angle to the chair • Seat / back tilting ratio of 1:2 • The mechanism housing should be made up of HPDC Aluminum & black powder coated (DFT 40 to 60 micron) SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 3.75±0.1 cm LUMBAR SUPPORT ASSEMBLY: The Lumbar support assembly should consist of lumbar spine (material-Glass Fiber Filled Nylon) which should be fixed to Aluminum Back spine. The Lumbar pad (material- Poly Propylene) should be fixed to lumbar spine through lumbar Pad support. Lumbar Support Assembly has height adjustmentof 5.0±0.5cmPNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3cm.PEDESTAL ASSEMBLY WITH CASTORS:The pedestal should be High Pressure Die cast polished Aluminum and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.)TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black PP having 6.0± 0.1cm wheel Diameter. as per 3D view matching with Photographs as attached in RFP

Supply & Installation of Reception Table 1850x750x1100 (l*b*h) Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire management Secondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Drawer under counter in fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Drawer extension should be 325 MM. Drawers should have a soft closing & anti slam mechanism. Handles should be provided for ease of opening. Pedestals should be provided with lock for security. Provision and fixing for 3 set of 5/15 AMP Switch/Sockets along with 1 no. LAN Sockets should also be there including supply & provision of connector for Laptop connectivity. as per 3D view matching with Photographs as attached in RFP.

Supply & Installation of Manager Table 1250x750x770 (l*b*h) Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire management Secondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedestal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension should be 325 MM. Drawers should have a soft closing & anti slam mechanism. Handles should be provided for ease of opening. Pedestals should be provided with lock for security. Provision and fixing for 3 set of 5/15 AMP Switch/Sockets along with 1 no. LAN Sockets should also be there including supply & provision of connector for Laptop connectivity. as per sketch/drawing matching with Photographs as attached in RFP

Supply & Installation of Center unit for Sofa Overall Size : Width : 118cm Depth : 60cm Height : 45cmTABLE METERIALS & SIZE :TOP:Sheesham 18 mm LEGS: 80X80 Top Side 40X40 Bottom Side Support 45x25mm & 8 Pcs Bolt & Nut as per 3D view matching with Photographs as attached in RFP

Supply and Installation of Conference Table size 10'*4' table and 30" height with laminate finish and leg to be box section MS powder coated. Design and detailing to be engineer in charge.Provision for 3 set of 5/15 AMP Switch/Sockets along with 1 no. LAN Sockets should also be there including supply & provision of connector for Laptop connectivity.

Providing and fixing soft boards , without any frame work and beading including providing and fixing fabric of approved make and colour etc., all as per drawing & engineer's instructions.

Supply and Installation of credenza: structure made up of 18 mm thick Prelaminated partricle board with 2mm thick PVC edge banding tape.Approx. dimension 1200(w)*450(D)*1200(H).

Supply & installation of Manual Roller blinds having Aluminum Roller tube along with fabric pasted on it with glue having control unit for manual operations and bottom bar Aluminum powder coated for weight purpose, including fabric, fitting & accessories of approved make & colour etc. complete.

Providing and fixing graffiti (hand paint Modern abstract)Design and detailing as per engineer in charge. Please refer reference image

Ceramic writing board with 25 X 40 beechwood/ approved beading on 12mm ply - size 2400 x 1200

Providing and fixing hoardings outside the building as per size give by engineer in chargeApprox. Dimensions:1200mm(W) X 900mm(H) with provision of backlight

Providing and fixing of in reception made up of laser cut Anti-Corrosive high grade AISI 316 Stainless Steel size 1mtr by 1mtr .details given by engineer in charge.

Providing and fixing Name plate for individual cabin and rest of the area. Signage's are made up of laser cut Anti-Corrosive high grade AISI 316 Stainless Steel of 2mm thick sheet with laser cut method for impression and with satin finish. Approx. Dimensions: 300 mm X 170 mm X 2 mm.Design and detailing provided by as per engineer in charge

Electrical (supplying and fixing of following items)

Wiring of light point/ fan point/ exhaust fan point/ call bell point as per specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit & it's all accessories( J.B. , Bends etc.) , round tiles,18 SWG Hot Dipped Galvanized Modular Box with earth terminal, 6 A Modular switch, Modular face plate with grid plate, 3 pin ceiling rose / lamp Holder/ 3 pin connector , screws etc, making connections,all as per pre approved by Engineer in charge, testing etc. complete as required as per recommended makes of RFP.

Short point (up to 3 mtr.)

Medium point (up to 6 mtr.)

Long point (up to 10 mtr..)

Wiring of 3/5 pin 6 amp. Light plug point as per specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit & it's all accessories( J.B. , Bends etc.) , round tiles, 18 SWG Hot Dipped Galvanized Modular Box with earth terminal, 6 A modular switch, 3/ 5 pin 6 A modular socket, Modular face plate with grid plate, screws etc,all as per pre approved by Engineer in charge, making connections, testing etc. complete as required as per recommended makes of RFP .

On board

Short point (up to 3 mtr.)

Medium point (up to 6 mtr.)

Long point (up to 10 mtr..)

S&F following sizes (dia.) of ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit as per specification for electrical Works along with its accessories (IS: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required as per recommended makes of RFP .

P & F 3 Way, 4 Conductors with current rating 16 Amp. Connector

S&F following sizes of ISI marked DLP U-PVC mini trunking systems along with accessories like end cap, internal angle, external angle ,Flat angle, Flat junction etc. on surface with screws, expansion fasteners as required. (make: legrand)

Mini-Trunking -32 x 12 mm

Finishing Accessories

End cap right or left

Changeable internal-external angle from 600 to 1200

Changeable flat angle from 850 to 950

Flat junction

White 32 x 10/12.5 cover joint

Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4, , in existing surface or recessed PVC/ MS conduit/casing capping including all as per pre approved by Engineer in charge,making connections, etc. as require as per recommended makes of RFP.

3x 1.5 sq.mm

2 x 2.5 sq. mm. + 1x1.5sqmm

2 x 4.0 sq. mm. + 1 x 2.5 sq. mm.

2 x 6.0 sq. mm. + 1 x 2.5 sq. mm.

4 x 10.0 sq.mm

Supplying and fixing of power plug point with Modular accessories as per specification for electrical Works, on hot dipped galvanized modular box of 18 SWG with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost of ISI marked modular 16 amp. Switch (IS :3854) and 3/5 pin 16 amp. socket outlet (IS:1293) , making connection , testing , etc. as required. All as per pre approved by Engineer in charge, as per recommended makes of RFP.

Providing & Fixing of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load and site requirement) 4KV impulse withstand voltage, as per specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , IP 20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A rating including making connections, testing etc. as required. . All as per pre approved by Engineer in charge and as per recommended makes of RFP .

Single pole MCB

6 A to 32 A rating

Double pole MCB

40 A to 63 A rating

Four pole MCB

40 A rating

50-63 A rating

Providing & Fixing of 240/415 V Residual current circuit breaker (RCCB) as per specification for electrical Works with ISI marked (IS:12640-1) / conforming to IEC 61008 -1 , rated conditional s/c current of 10 KA, truly current operated and shall operate on CBCT mechanisum, provision for pad lock, min. operation 10,000 upto 63 A rating and 5000 for 100 A rating, minimum phase termination capacity of 50 sq.mm. rigid wire , IP 20 contact protection with existing distribution board / sheet including making connections, testing etc. as required. All as per pre approved by Engineer in charge, as per recommended makes of RFP .

Two pole 100/300mA sensitivity

40 A rating

Four pole 100/300 mA sensitivity

40 A rating

63 A rating

SITC of wall/ free standing floor mounted dust and vermin proof compartmentalised cubical panel as per specification for electrical Works, made out of CRCA sheet . Other parameters required as per point (a) ,(b), (c),(d) below:- (a)Thickness of sheet shall not be less than 1.6 mm up to 600 mm length / width of any compartment and be of 2.0 mm above 600 mm. Load bearing structure shall be of 2.0 mm thick sheet supported by base M.S. channel if required . Side walls and cable alley compartments having bolted type doors with / without detachable extension type structure (b)panel shall be duly treated for derusting in 7 tank process with dephosphating and with powder coating of minimum 70 microns on both side of panel in desired shade The panel having PU/ Neoprene rubber gasket of not less than 3mm thickness ,required hardware, separate detachable gland plate M.S. base channel (min75mm) , hinged door with locking arrangement for equipment/switchgear [c) Interconnection between bus bar and switchgears /cable shall be rigidly supported and made out by flexible copper wires (up to 125 amp ) and by solid bus bar (>125 amp ) . All joints / interconnections of copper bus bar shall be dully tinned . Clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar Bus bar is insulated by Heat Shrinkable sleeves . Earth and Neutral bus bar shall be half of the size of phase bus bar. (d) only outer area on all sides shall be measured & panel to be fabricated only from CPRI approved fabricator. All as per drawing pre approved by Engineer in charge. as per recommended makes of RFP .

Supplying and fixing of Aluminium (IEC 60105 ISO 209-1,2) / Copper (IEC 60028) bus bar as per specification for electrical Works, by means of SMC / DMC type insulator, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable PVC sleeves. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Electrolytic grade Aluminium bus bar 6010 grade

Providing & Fixing of BIS approved Current Transformer as per specification for electrical Works ,ISI marked as per IS 2705-1992/ conforming to IEC 60044-1, with secondary terminal of CT shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as required Current transformer Resin Cast Wound Primary / Ring Type Tape Wound as per IS 16227 with, Accuracy Cl, CT ratio and burden as specified. ISF<=5, Cu cross section of secondary wire 1.5sqmm (minimum), including all necessary support in existing panel including connection etc. as required . All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

C T Class 1, Ratio upto 150/5, Burden 5 VA

Providing & Fixing of ISO certified company made UL listed , IP 65 110/220 V, unibody LED Indicating lamp IEC 60947 , CSA 22.2 with integral circuit, IP 20 terminal block, Approx. body dia for panel not less then 20 mm, length min. 50mm, front LED cover dia min. 29 mm, contact material phospher bronze for Led, PCB contacts shall be of brass (tin plated), impulse dielectric tested for 2.5 KV, Rated insulation resistance shall be 100 M ohm at 500VDC including connection etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Red/yellow/Green colour

Providing & Fixing of IP 51 Multi function meter as per specification for electrical Works, ISI marked (IS 16444)/ Confirming to IEC 61557 & IEC 62052 with LCD/ LED 3/4 line display capable of measuring electrical parameters like V, I, F, PF, KW, Kva, Kvar, Kwh, Kvah, Kvarh display with 1A/5A CT input for LV/ HV network, with /without RS 485 communication port etc. All as per pre approved by Engineer in charge. as per recommended makes of RFP .

Multifunction LCD meter with V, I, F, PF, KW, Kva, Kvar, Kwh, Kvah, Kvarh, Run hours, On hours, Phase angle, Interrupts, THD, Events, Neutral Current class 1 accuracy with RS485 port.

Providing & Fixing of recessed/surface mounting heavy duty sheet steel 1.6 mm thick End Box as per specification for electrical Works for distribution board duly phophatised powder coated complete as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

For TPN 4 Way

For TPN 8 Way

For SPN 16 Way

Providing & Fixing of following modular accessories as per specification for electrical Works, made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , minimum width of 1 module switch toggle( PUSH PART ) should not less then 20mm, including all as per pre approved by Engineer in charge,making connections, testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Blanking plate

Providing & Fixing of ISO certified company made vergin material PVC trunking system as per specification for electrical Works, with double lock feature for cable management including finishing accessories like corners, tee, adjustable angles, junction etc. as required . The trunking system shall have adaptable system for modular type RJ 45 data socket/ wiring accessories/ power sockets and shall be covered with peal off plastic cover. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

80mm x 50mm

SITC of chemical Gel earthing system of Dual Pipe Technology made of with "B" Class G I Pipe as per IS 1239 ( part-1):2004 of Medium duty of following sizes as per points mentioned (a), (b), [c), (d), (e) below :- (a) filled with anti corrosive conductive compounds with the permanent sealings at both the ends, CPRI/ ERDA tested with RMS capacity of minimum 35- 40 KA for withstanding 1 second . (b) To ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 Kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. The compound shall be tested form NABL acredeated lab for low resistivity ( less than 0.12 Ohm - meter) & high conductivity in nature with carbon as a major content as per referance of IS 3043-1987,IEEE 80-2013 (clause 14.5d) , IEEE 837 & IER 1956 with latest amendemnts ©Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. (d) Testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book. (e) All as per pre approved by Engineer in charge. as per recommended makes of RFP .

With Pipe in Pipe Technology (Outer pipe dia. / Inner pipe dia. ) Minimum 100 mm dia borewell

GI pipe 3000 mm long, 80 / 50 mm, Terminal 50 mm x 6 mm GI Strip

Supply & Laying following size earth strip in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, Jointing shall be done by overlapping and with 2 set of Brass (for Cu strip) / GI (for GI Strip) nut bolt & spring washer spaced at 50cm making connection etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

25mm x 3mm copper strip

Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with GI/Cu thimble etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

8 SWG copper Wire

Supply & fabrication steel structure with MS channel / angle / joist / ISMB / sheet etc. including welding, rivetting, cutting, nut & bolt , one coat of primer & two coat of enamel paint etc. as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

SITC of IP 40 quick make and quick break 4 pole current limiting Moulded case circuit breaker (MCCB) made of flame retardent & heat resistant material having following current rating, short circuit breaking capacity at 440/415 V, 50 Hz; O/L & S/C settings as per specification for electrical Works, conforming to IS/IEC 60947 P -2 :2003 with front face and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push (test) to trip, trip time less then 10 ms under s/c condition, Breaking capacity Ics = 100% Icu. U imp =8 KV, rated insulation voltage 800 V, provision for UVR , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connections with lugs & spreaders, etc. as required. All as per pre approved by Engineer in charge. as per recommended makes of RFP .

With Thermal Magnetic release

up to 100 Amp , 25 kA, adjustable O/L & fixed S/C setting, Ics = 100 % Icu

Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-armoured / Armoured aluminium cable of 1.1 KV grade as per specification for electrical Works in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points (a), (b), (c), mentioned below:- (a) Material :- H4- Grade aluminium conductor of purity >99.6 % & as per IS:1554 P-I / IS :7098 P - I (b) conductor shall have electrolytic aluminium confirming to IS 8130, IS 3975-1999 for armouring of cables in armoured cable items , IS 5831 for sheath, IS 10810 (Part 0 to 64 ) for testing procedures . (c) All above as per pre approved by Engineer in charge. as per recommended makes of RFP .

Armoured Cable

Supplying and making one end termination with heavy duty brass compression gland (as per IS 12943- 1990) SIBG type, heavy duty aluminium lugs (as per IS 8309 -1993 & IS 8337-1976 ) duly crimped with crimping tool, PVC tape as per specification for electrical Works etc for following size of Armoured PVC insulated & PVC sheathed/ XLPE aluminium conductor cable of 1100 volt grade as required of size. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

4 x 16.0 sq.mm

3.5 x 35.0 sq.mm

Providing & Fixing of IP40 LED Surface/ Recessed / suspended mounting Mid power SMD type LED Light fixture made from CRCA sheet steel housing, high purity / transmisivity UV stabilized Non -yellowish diffuser for uniform light distribution. High efficiency with 2.5 KV internal/external surge protection BIS certified isolated driver having efficiency > 85% , with Short & Open circuit protection and in compliance to IEC standards (Integral with light fixture). System lumen efficacy of ≥ 120 lm/Watt ,THD < 10 % , p.f.≥0.95,CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.

48W LED light fixture 2'x2' with acrylic / prismatic front cover.

Providing & Fixing of IP40 LED Recessed / Surface Mounted, Round / Sqaure Non-Dimmable Back lit SMD Mid Power LED Downlight with die-cast aluminum housing & Heat Sink for heat dissipation with UV Stabilized non yellowish Diffuser with internal/ external BIS complience 2.5 KV surge protected Isolated driver, with Short & Open circuit protection, having efficiency > 85% and in compliance to IEC standards. System Lumen efficacy of ≥ 120 lm / watt, THD < 10 % ,p.f.≥0.95, CRI >80, life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.

Recessed Mounting

LED Downlight 18/20W

Supply & Laying following size' B ' class , Medium class G.I. Pipe confirming to IS : 1239 P - 1 ( 2004 ) with accessories like bend, socket etc. for laying earth conductor/ strip / cable in ground/ surface/ recess as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

32mm dia

Providing & Fixing of Heavy duty capacitor start, copper woind Double ball bearing 900/1400 RPM single phase Exhaust fan as per specification for electrical Works, conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as required. All as per pre approved by Engineer in charge. as per recommended makes of RFP .

300 mm sweep(900/1400 RPM)

Supply, Fabricating & installing following sizes of powder coated perforated M.S. cable trays with perforation not more then 17.5% in convenient section including horizontal and vertical bends, reducers tees,cross members and other accessories as required and duly suspended from the ceiling with MS suspenders including bolts & nuts , fastners, supports, painting suspenders etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

150mm x 50mm x 1.6mm

Supply & Fixing of ABC Type (MAP 50) type powder Fire Extinguisher (Stored Pressure type) of following capacity duly current and valid BIS certification conforming to IS: 15683:2006, with Dry chemical powder used as extinguishing agent should be Mono Ammonium Phosphate 50% concentration conforming to IS 14609:1999. Serial no. and date of manufacturing should be embossed or printed on the body of the fire extinguisher. . All as per pre approved by Engineer in charge. as per recommended makes of RFP .

Providing & Fixing of of M.S. J- hook of standard design made out of 16 mm dia. M.S. round bar and fixed with cement concrete mortar with required support as required.

Providing & Fixing of ISO Certified company made BEE Approved copper wounded 1200 mm sweep BLDC technology power saving ceiling fan with longer life span and low maintenance 5 star rated which can withstand on votage fluctuations from 140 volts to 240 volts ,power factor not less then 0.9 , service value (CMM/W) minimun 6.85 , air delivery minimun 215 CMM, speed 350 RPM ( tolerance as per IS:374 2019 ) THD less then 10% and complete with down rod up to 30 cm with secondary support safety cable , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge. as per recommended makes of RFP .

Without Remote

Providing & Fixing of heavy duty, copper wound , Double ball bearing and with metal sturdy mesh guard; Aluminium alloy one piece blade wall mounting oscillating type air circulator as per specification for electrical Works, conforming to IS:2997, including fixing with anchor bolts, regulator making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

450 mm sweep With wall Mounting and three speed regulator

SITC of raceway confirming to EN 50 085-2-2, IP-20, IK-08 for distributing cablling for screed floora installation & particularly suitable for applications requiring EMC screening material/GI raceways made up of pregalvanized sheet (DX51D-Z120 MAC) in desired color, non corrosive, non flame propagation, with 2 to 2.5 mtr, standard length/standard depth 25mm / 38mm, thickness 1.6 mm for raceways, 1.0 mm for partition with coupler for joining raceways including making jhiris on floors/wall if required of following sizes. Make: legrand / MK

SITC of GI junction box with removable precuts knockouts provided for raceways resistance to vertical load over a small area, 500N and for large surface area 2000N with adjustable height 50 to 70mm with flyover as required . Make: legrand/MK

SITC of 10 KVA 3 Phase Input, 1 Phase Output advance DSP controlled UPS with IGBT based rectifier, LCD display, double conversion / Digital Signal Processing UPS, with isolation transformer, with 30 minute battery back up, with required cabling for incoming & outgoing connection (Approved makes: Emerson / Numeric / APC)

Technical Specification: Phase: 3 Pahse in /1 Phase out Capacity : 10000 VA /9000 W Input Characteristics : Nominal Voltage : 3 X 400 VAC (3 Ph +N) Voltage Range: 305-478 VAC(3-Phase) @ 100% Load Frequency Range: 46~54 Hz or 56~64 Hz Power Factor - >= 0.99 @ 100% Load THDi : < 6% @ 100 % load

OUTPUT Characteristics : Output Voltage : 208/220/230/240 VAC AC Voltage Regulation (Batt, Mode) : ± 1 % Frequency Range (Synchronized Range) : 46~54 Hz or 56~64 Hz Frequency Range (Batt. Mode) : 50 Hz ± 0.1 Hz or 60 Hz ± 0.1 Hz Current Crest Ratio : 3:1 (max.) Harmonic Distortion : ≤ 2% THD(Linear Load) ; ≤ 5 % THD (Non- Linear Load) Transfer Time (AC Mode to Battery Mode): Zero Transfer Time (Inverter to Bypass) :Zero Waveform (Batt. Mode) : Pure Sinewave AC mode Efficiency : ˃ 92% ECO Mode Efficiency : 97 %

BATTERY Characteristics : Battery Type : SMF or Tubular Battery Nos. : 20 Charging Current (Max.) : 12 A settable to 2/4/6/8/10/12 Amps Charging Voltage: 273 VDC ± 1 % (Based on 20 pcs batteries)

Indicators: LCD Panel : UPS status , Load level, Battery level, input/output voltage, Discharge Timer and Fault Conditions

Alarm: Battery Mode : Sounding every 4 seconds Low Battry : sounding every second Overload : sounding twice every second Fault : continuously sounding

10 KVA 3 Phase Input, 1 Phase Output

LAN Services

Supply , Installation, Testing and Comissioning of Wall mounted Communication rack with glass doors, handles ,lock , Top and Bottom Cable entries, Supports for mounting rack on wall , Cable managers, one Fan, Equipment mounting hardware, power supply box for supplying power to switches, fans etc along with earth continuity kit, Mcb, indicator, moulded power supply cable

12 U(44 mm ) wall mounted

Supply, Installation, & Testing of 19" 1U Rack Mounted/ surface mounted aluminum/ CRCA 1.2mm powder coated, multimode glass Fiber Optic Cable Patch panel/LIU loaded with flangless/screwable adapters for ST/E-2000/SC/LC/MT-RJ/PC type, It should have easy removable Top plate with push buttons, there should be a splice tray installed in the Patch panel/LIU which can handle the fiber cores, splice tray should be PC+ABS material, it should include accessories like mounting hardware, gormetts, heat shrink tubes/sleevs, screws, nuts to install the panel for rack/wallmount applications as per requirement complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Multi Mode LIU 6 Ports

Supply, Installation, & Testing of Indoor duplex Multimode patch cord (50/125 µm made of glass fiber optic with LSZH jacket, Multimode G652.D Mounted on both sides with ST/E-2000/SC/LC/MT-RJ/PC type Duplex connectors in acc. with IEC 61754-20 as per latest ammendments of TIA/EIA 569B.3, as per requirements complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Supply, Installation, OTDR Testing & Fusion Splicing of Fiber Multimode Pigtail (50/125 µm) made of glass fiber optic, should be fitted at one end with any one type of single ST/E-2000/SC/LC/MT-RJ/PC type connector in acc. with IEC 61754-20, as per latest ammendments of TIA/EIA 569 Standard Specification as per requirments complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Supply, Drawing and Testing, of stranded Multi mode (50/125 µm) glass optic fiber cable, as per latest ammendments of TIA/EIA 568/ISO/IEC 11801:2011/ IEC 60794-1-2 E1, E3,E11, F1/ EN 50173-1/ EN 187 000/ IEC 60974-2, 2-20, 2-21/ ITU G.652D, construction of LSZH outer sheath cable, cable should be used for LAN and WAN back bones, . With its LSZH sheathing these cables should be ideal for indoor/outdoor installations in existing MS/PVC /HDPE Conduits/ slotted channels with ferruling at both ends for identification complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

6 core 10G optical fiber cable

SITC of Intelligent Ethernet POE Switches providing 24 x 10/100/1000 Fast Ethernet POE ports- 370W or better and 4 dual purpose uplink (provision for Copper / Fiber Giga connectivity) with provision of minimum Stacking of 06 Switches with related LAN Base Software . For additional technical parameters of products/ work as per recommended makes of RFP.

Supply, Installation, Testing and Comissioning of Rack mounted , 48 x 10/100/1000 Ethernet ports Gigabit Switch with 4 mini Gigabit Interface Converter slots(shared with 4 Ethernet ports) for Gigabit Ethernet expansion , Switching capacity 96 Gbps nonblocking , . As per recommended makes of RFP.

Supply, Installation, Testing and Comissioning of 1G SFP (small form-factor pluggable) transceivers as per recommended makes of RFP.

Supply, Installation, Testing and Comissioning of 10G SFP (small form-factor pluggable) transceivers as per recommended makes of RFP.

Supply, Installation, Testing and Comissioning of Rack mounted 19" 1U, 24 Port Unloaded, 1.5-1.6 MM CRS chasis, powder coated, sheet steel, made of plastic (ABS), Modular Patch Panels (without I.O.) with Rear Cable management system and mounting hardware to mount the patch panel. Should have port identification numbers printed/engraved on front of the panel, . There should be a provision for each port/jack on the panel and reusable removable on field from the panel complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Supply , Installation and Testing of 4 pair, 100 Ohm impedance, Cat 6/6A patch cords should be constructed of minimum 23/24 AWG, stranded bare Copper cable with FRPVC/LSZH Jacket, with an enhanced performance by factory moulded RJ45 connectors as per ANSI/TIA/EIA 568 suitable for Cat 6/6A application complying to latest ammendments Category 6/6A Standards, According. to TIA568, minimum requirement for 1G BASE-T/ 10G BASE-T performance. Patch cords shall be straight thru cable compatible with both T568-A and T568-B wiring schemes, Minimum 750 to 1000 mating cycles in plug contacts for long durability complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Cat 6, UTP (Un-sheilded Twisted Pair) Patch Cord

Supply, Drawing and Testing of 4 pair, 23 AWG Solid Bare Copper wire insulated with PVC, UTP (Unshielded Twisted Pair), Category 6, Class E, 100 Ohm Impedance, Indoor Cable as per latest ammendments of ANSI/TIA/EIA-568 , The copper conductors should be balanced twisted in pairs, seperated by a cross-member fluted pair divider & protected by PVC Jacket. Certified performance in a 4-connector configuration upto 100 Mtrs channel requirements & transmission frequencies up to 250 Mhz. in existing MS/PVC Conduits/casing capping including making connections to Information outlets and Patch Panels with jack & ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Supply and Installation of unsheilded/ sheilded Information outlets made of high impact plastic body with ABS, FR Grade with provision for protection against dust in jack/ FP, suitable for Cat 6/6A application complying to latest ammendments, According. to Cat. 6/6A channel, It should support channel as well as components requirements of Cat.6/6A standards at frequencies of up to 250 to 500 Mhz. Cat 6/6A unshielded/shielded Jack should be suitable to terminate 4 pair, 23/24 AWG solid/stranded wire diameters, using 100 Ohm unshielded/shielded balance twisted pair cable, the jack should have tooless/impact punch termination on reliable copper tin plated Insulation displacement contact, It complied with ANSI/TIA/EIA 568 standard. In existing modular/MS Boxes along with necessory connections as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Cat 6, Un-sheilded Information Outlet

Supply & fixing of square Faceplate for Flush / Surface Mount Information Outlets Single/Dual or Quad Aperture , material should be PC+ABS body, Suitable for RJ45 unshielded/shielded connection modules. Should match with I. O. . Dimensions should be 86mm X 86mm as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Single Aperture

SITC of Workstation latest Intel® i5 processor, Intel Chipset motherboard, 08 GB RAM, 1 TB SATA HDD at 7200 rpm, with 4GB GPU type higher end Graphic card for H.265 compression technique with dual display ports/DVI/ HDMI port, Giga LAN Card, wireless Keyboard, wireless optical Mouse, (Approved Makes: Dell, HP, Lenevo)

SITC of 5 MP IR Fixed Dome Network Camera -1/2.7 inch Progressive Scan CMOS, 2592 × 1944 at 25fps, 2.8 mm Fixed lens, 0.003 Lux at F1.4, 0 Lux with IR on, ICR, ONVIF (PROFILE S, PROFILE G, PROFILE T), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, BLC, HLC, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 256 GB (SD card not included), IP67, IK10, Edge Analytics- Line crossing detection, Intrusion detection, Motion detection, Region entrance detection, Region exiting detection, Scene change detection, Face capture, Video tampering, audio exception detection, False alarm reduction through human and vehicle target classification based on deep learning UL, CE, FCC certified.Approved brand:- Pelco, Prama, Axis, hikvision

SITC of 32 Ch Smart Network Video Recorder : Connect Up to 32 IP Cameras, Dual OS, Up to 12 Megapixels Resolution, 2 HDMI at least 1 HDMI 4K, 2 VGA atleast 1 VGA 2MP Output , Support H.265, MJPEG, Incoming Bandwidth 320Mbps, 8 SATA Hard Disks, ANR Technology, 8 SATA interfaces for 8 HDDs and capacity of each HDD upto 6TB, 3 × USB 2.0 at least 1 USB with 3.0, Alarm I/O 16/4, RS-485, RS-232, 2 RJ-45 10 /100/1000 Mbps self-adaptive Ethernet interface,two 8 tb hardisk included, Multiple network monitoring: Web viewer, CE, FCC, UL certified.Approved brand:- Pelco, Prama, Axis, hikvision

providing and fixing of Interactive Display65' with mounting kit Approved Makes:- Hikvision, samsung, Sony

Fire Services:

Supplying and drawing FRLS PVC insulated & unsheathed flexible copper conductor as per specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC 60228. FRLS PVC insulation which provides better fire retardant properties then normal PVC & also emits Low Smoke in case of fire & use type A insulation PVC, in existing conduit including , all as per pre approved by Engineer in charge,making connections, etc. as required. For additional technical parameters of products/ work refer recommended makes of RFP .

2 x 1.5 sq.mm

SITC Conventional Optical type Smoke Detector with mounting base, LED etc. as required.

SITC of conventional type Manual call point complete with Glass, hammer and chain etc. as required.

SITC 6 watt Speaker mounted in M S sheet box with perforated front mesh for PA and Emergency System.

SITC of wall / floor type following zone (each zone accessing minimum 20 units (detectors/ devices ) Conventional Type microprocessor based with LCD display main control panel/ floor panel fabricated from 16 SWG CRCA sheet steel sealed maintenance free (SMF) batteries of min2X7AH of 12 V or as required.

Specification: (i) Three Form-C relays (1 Fire, 1 Fault and 1 Fire/Fault 2 Amps@30VDC (ii) 1 On-board NACs operating @ 0.5 A/circuit (iii) Aux Output : 24 VDC (iv) Sounder Output : 24 VDC (v) Feature Detection Circuits: 4 Zones ( upto 20 Detectors + 5 MCPs) (vi) Zone wise Fire, Fault , Disable indication (vii)Panel keys : Silence Buzzer/ Alarm, Reset, Navigation keys (Left, Right, Down, Menu/Ok) (viii) Lamp Test & Walk Test (ix) Standby power 24V DC (2 no's of 12V, 7Ah Lead Acid Battery) (x)Certification (CE, LVDE) (xi) Event Log- 1200 events (xii) Earth fault monitoring

User Interface: Display: 16 X 2 character LCD Control Keys: Menu/Ok, Silence, Navigation and Reset buttons Indicators: Fire, Power, Fault, NAC Fault, Earth Fault, Silence

Wiring Details: Mechanical Specifications : Construction: Cold Rolled Steel with powder coated finish with door lock Cable Entry : 08 Number x 20.50 mm knockout Electrical Specifications: Operating Voltage: 230 VAC, 50 HZ Alarm Load(Sounder) 0.5 A (max) NAC output 0.5Amp.(max) Operating Temperature : 0oC~ 49oC Relative Humidity : 5 % to 95 % non -condensing Standby Batteries : Minimum capacity (2 X12 V 2.8 Ah); Maximum Capacity (2 x 12 V 7 Ah) Detection Circuits : 2,4,zone , max 2 mA per detector class B circuit External outputs : sounder output (18.5 to 28.0 Vdc, 0.5 Amp.(max)); Auxiliary Output ( 18.5 to 28.0 Vdc, 0.5 Amp.(max))

Compatible Devices: System sensor Photo Electric Smoke Detector, System sensor Photo Electric and Heat detector, System sensor Plug-in detector base System sensor MCP Red W/O Back Box System sensor Horn cum strobe , wall , Red, Standard Candela

HVAC Services

Supply, Installation, Testing and balancing of powder coated /Anodised extruded aluminium construction inlet fixed single air louvers with bird screen for Exhaust air of size upto 1.0 sqft area, Installation has been done on the Exhaust Fan of make Systemair / Ravistar / Trox/MetalJoint/Airflow.

SITC of Air Cooled split type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (EP foam pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 4 Mtr (IDU to ODU), R-22/R-410 Refrigerant, Remote, suitable for 400/230V +10% of 50 Hz ,1 /3 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / reciprocating / rotary compressor as specified.

Hi Wall/Ceiling Wall Split

1.0 TR with 5 star rating of BEE

1.5 TR with 5 star rating of BEE

2.0 TR with 5 star rating of BEE

SITC of Interconnecting refrigerant pipe work with closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications including chase cutting, supports etc. as required.

Providing and fixing of cPVC drain water piping complete with fittings, support with MS hanger as per specification and insulated with 6 mm thick closed cell elastomeric nitrile rubber insulation. Make: cPVC Pipe -Supreme / Astral / Kisan. Insulation - Armaflex / Supreme/ Superlon / Aflex /Kflex.

32 mm dia O.D

25 mm dia O.D

Making hole in stone masonary/ RCC wall/ RCC slab with core cutter for accomodating refrigerant pipe/ drain pipe/ MS pipe/ cables etc of following dia

150 mm dia per running inch length

Water Purifier

Providing and fixing Kent or Equivalent water fountain chillar cum inbuilt RO water purifier with cooling capacity 30 Ltr per hour@ 14-22 degree C and no of faciets to be 2 (1 cold+ 1 normal)

Description of Work / Item(s)

Amount

Civil (supply and execution of following items)

Demolishing/dismentling manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material All lead and lift from site upto 5km outside the site (dispose of the material) at safe place

Brick work, Stone Masonry, Plastering, Flooring/ Dadooing /skirting/tiles all types (L.S.)

Joinery( door, window, ventilator, vent, WC, urinals, wash basin,exisiting railing & MS shutter) and handing over to local authorities (L.S.)

Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead : With cement mortar 1 :4 ( 1 cement : 4 coarse sand)

Partition Frame work made of 2" X 2" Aluminium spaced at 2'0" c/c vertically & horizontally. Additional member shall be provided at skirting, top band, grooves & at places where two different materials are combined. Necessary supports to the slab should be taken in to account. Partition panelling only with 18mm ply board The panels shall have grooves as per detail drawing finished with 1mm laminate as per design & detail. Shade and texture as per approved engineer in charge

providing and fixing of Glass partition (on to item no 3 or on masonry wall)using 10mm toughened glass with frosted film on frame all over aluminium frame. Design and detailing as per engineer in charge

Providing & fixing in position glazed entrance door which is frameless using 12mm toughened glass with edge polish. The door to consist of floor spring , Top patch, Bottom patch, Top pivot & S.S handle . Provide Patch lock .Cost to include silicon sealant. size is 8'*4'.Above lintel level fixed glass is to be fixed.The door shall be finished with privacy film.

Providing waterproofing to the roof by the following method Providing and applying one coat of Brush bond and Geo fabric laid between the screed concrete and brush bond . Provide proper slope for the rain water with 1 : 4 CM and marking of threads in regular intervals. Area and application to include 1m all over the parapet walls also.

Providing & fixing calcium silicate ceiling tiles of size 595 x 595 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanised steel sections ( galvanized @ 170 gsm/sqm.) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet spaced at 1200mm center to center and cross “T” of size 24x25mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main “T” at 600mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600mm and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 21x21x0.30 mm and laying false ceiling tiles of approved texture in the grid including, wherever, required, cutting/ making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats fixed to ceiling with 6 mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanised level clips spaced at 1200mm center to center along main‘T’ bottom exposed with 24mm of all T sections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawing and as directed by engineer-in-charge.8 mm thick

Providing and fixing False Ceiling as per India Gypsum Specifications made of standard G.I. Sections and 12.5mm thick gyp board sheets inclusive of all hangers, edge members and other clips complete, with sheets fixed with proper screws by power drills and joints duly finished ensuring level in line and plumb to take final paint. All inclusive of detailed cut-outs for light fixtures, AC grilles. All Vertical drops will be measured extra as per actuals.The cost to be inclusive of surface preparation ,3 coats of acrylic emulsion paint including the top coat as per INDIA GUPSUM STANDARDS ( MODE OF MEASUREMENT L x B) .

Providing & laying flooring,skirtring of vitrified tile over a bed mortar of 20 mm thk in CM 1:5 or chemical laying as per the instruction of engineer incharge, including slurry, having joints filled with cement of matching color including washing, cleaning etc tiles will be laid with 2 mm gap using spacers and gap will be filled with epoxy grouting complete as per specifications. Necessary protective covering to prevent damage for the finish flooring to be given 300 microns plastic sheet and POP spread over it at no extra cost and to be retained until handover size:600*600.

providing and laying of Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, making of lines or groove etc complete but excluding the cost of nosing of steps etc. complete. 75mm thick with 20mm thick nominal size aggregate.

Providing and applying acrylic emulsion paint finish to walls, blocked partitions, and plasterboard ceiling surfaces of approved shade, texture. Existing wall and ceiling surfaces to be prepared by scraping away any loose particles, dust, etc by washing and scrubbing and 1 coat of primer approved by manufacturer applied. The wall surfaces are then smoothened using putty approved by the manufacturers. Surfaces are then sandpapered to achieve a smooth finish and two or more coats of paint are applied as per manufacturer's specification.

Painting (two or more coats) on door and windows with synthetic enamel/Enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on new work. Colour to be taken approval from engineer-in-charge

Providing & fixing double leaf flush shutter formed out of 35mm thick factory made Ply of approved make finished with 1mm laminate of approved make on both sides . 12mm Beechwood beading to run around the shutter as shown in the dwg . 8 mm clear glass to be fixed to the shutter with concealed beading as per detail dwg

Flush shutter door - 32mm th. finished with laminate on both sides.. Shutter to have 35mm wide and 12mm thick lipping beading allround finished with enamel paint of approved brand, colour and shade., Cost to include necessary hardwares door closer, hinges, etc., complete. 8 mm clear glass to be fixed to the shutter with concealed beading as per detail dwg

Providing and fixing soft boards , without any frame work and beading and with 3mm thk foam including providing and fixing fabric of approved make and colour etc., all as per drawing & engineer's instructions.

Providing and laying 14mmthk FSC certified laminated wooden flooring of size 125mmx1850mm. The planks shall be provided with tongue & groove required for locking. The flooring to be layed with 5mm underlay foam and 60 microns LDF film placed over it as moisture barrier to proper level with necessary edge profile & transition strip where ever necessary complete as per manufacturers instructions. The rate shall include cost and conveyance of all materials,labor charges,lead,lift,laying Self leveling screed 3-5mm thk etc. all complete as specified and as directed by the Engineer-in-Charge

Repair and fixing of toilet fixture which includes pillar cock,connection pipe for urinals and wash basin,wastage pipe, repair of floor tiles. Cost to include repair of pipes, to check for any leakages and toilets to handover in work conditions

providing and fixing of Counter for hardware room: Includes half brick masonry work with plaster for partition wall up to the height of 770mm for counter of (length x breath) 3600mmx600mm. The counter slab work includes stone slab with top polished & moulded granite work.

Furniture

Supply & Installation of 2 Seater Sofa The seat should be made of PU foam with Density 32 ± 2 kg/cu.mtr having an additional top layer of J PU foam with Density 28 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 23±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure: should be made up of 1.2±0.1 cm. thick hot pressed plywood 4. Dia 4mm zigzag spring assembly should be mounted in understructure for support and additional cushioning purpose .it should be a welded assembly made in Stainless steel (grade SS 202) tube & plate. as per 3D view matching with Photographs as attached in RFP

Supply & Installation of 1 Seater Sofa The seat should be made of PU foam with Density 32 ± 2 kg/cu.mtr having an additional top layer of J PU foam with Density 28 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 23±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure: should be made up of 1.2±0.1 cm. thick hot pressed plywood 4. Dia 4mm zigzag spring assembly should be mounted in understructure for support and additional cushioning purpose .it should be a welded assembly made in Stainless steel (grade SS 202) tube & plate. as per 3D view matching with Photographs as attached in RFP

Supply & Installation of chair with headrest for 1 Person SEAT/BACK ASSEMBLY: The Cushioned seat assembly consshould be ts of seat outer (material-30% Glass Fiber Nylon)& upholstered Seat inner (material- Poly Propylene) with moulded Polyurethane foam & polyster fabric. The Net Back should be made up of Back outer (material-Glass Fiber Filled Nylon)& Back inner (material- PP) and upholstered using Polyester Mesh fabric with high tenacity yarn. Full Back Size: 46.5 cm. (W) x 60.0 cm. (H) Seat Size : 51.0 cm. (W) x 49.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density = 45 +/- 2 kg/m³ and Hardness load 12 +/- 2 kgf for 25% compression. BACK SPINE: The support spine should be made up of High Pressure Die cast polished hed Aluminum. ARMRESTS : The armrest should be having two adjustment, Height (6.0±0.5cm) and Depth (6.0±0.5cm). Height adjustment should be provided in Aluminum structure of armrest which should be connected to Aluminum Back spine and should be operated by button. The depth adjustment should be provided in pad which should be fixed to armrest structure. Armrest Top should be made up of PU molded over plastic inner.ACTIVE BIO-SYNCHRO mechanism: The adjustable tilting mechanism should be designed with the following features: • 360° revolving type • Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort • Tilt tension adjustment can be operated in seating position • 5 position Tilt limiter giving option of variable tilt angle to the chair • Seat / back tilting ratio of 1:2 • The mechanism housing should be made up of HPDC Aluminum & black powder coated (DFT 40 to 60 micron)SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 3.75±0.1 cmLUMBAR SUPPORT ASSEMBLY: The Lumbar support assembly should consist of lumbar spine (material-Glass Fiber Filled Nylon) which should be fixed to Aluminum Back spine. The Lumbar pad (material- Poly Propylene) should be fixed to lumbar spine through lumbar Pad support. Lumbar Support Assembly has height adjustment of 5.0±0.5cm PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3cm. PEDESTAL ASSEMBLY WITH CASTORS:The pedestal should be High Pressure Die cast polished Aluminum and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.) TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black PP having 6.0± 0.1cm wheel Diameter..The neckrest assembly consshould be ts of upholstered Neckrest inner(material-PolyPropylene) with moulded Polyurethane foam and Polyster fabric.Upholstered inner should be fixed to Neckrest cover.Neckrest should be fixed to Back assembly through Neckrest spine .Neckrest assembly has height adjustment of 5.5 +/- 0.5cm and Rotation adjustment of overall 20° +/- 2° as per 3D view matching with Photographs as attached in RFP

Supply & Installation of Chair without headrest SEAT/BACK ASSEMBLY: The Cushioned seat assembly consshould be ts of seat outer (material-30% Glass Fiber Nylon)& upholstered Seat inner (material- Poly Propylene) with moulded Polyurethane foam & polyster fabric. The Net Back should be made up of Back outer (material-Glass Fiber Filled Nylon)& Back inner (material- PP) and upholstered using Polyester Mesh fabric with high tenacity yarn. Full Back Size: 46.5 cm. (W) x 60.0 cm. (H) Seat Size : 51.0 cm. (W) x 49.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density = 45 +/- 2 kg/m³ and Hardness load 12 +/- 2 kgf for 25% compression. BACK SPINE: The support spine should be made up of High Pressure Die cast polished hed Aluminum. ARMRESTS : The armrest should be having two adjustment, Height (6.0±0.5cm) and Depth (6.0±0.5cm). Height adjustment should be provided in Aluminum structure of armrest which should be connected to Aluminum Back spine and should be operated by button. The depth adjustment should be provided in pad which should be fixed to armrest structure. Armrest Top should be made up of PU molded over plastic inner. ACTIVE BIO-SYNCHRO mechanism: The adjustable tilting mechanism should be designed with the following features: • 360° revolving type • Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort • Tilt tension adjustment can be operated in seating position • 5 position Tilt limiter giving option of variable tilt angle to the chair • Seat / back tilting ratio of 1:2 • The mechanism housing should be made up of HPDC Aluminum & black powder coated (DFT 40 to 60 micron) SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 3.75±0.1 cm LUMBAR SUPPORT ASSEMBLY: The Lumbar support assembly should consist of lumbar spine (material-Glass Fiber Filled Nylon) which should be fixed to Aluminum Back spine. The Lumbar pad (material- Poly Propylene) should be fixed to lumbar spine through lumbar Pad support. Lumbar Support Assembly has height adjustmentof 5.0±0.5cmPNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3cm.PEDESTAL ASSEMBLY WITH CASTORS:The pedestal should be High Pressure Die cast polished Aluminum and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.)TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black PP having 6.0± 0.1cm wheel Diameter. as per sketch/drawing matching with Photographs as attached in RFP

Supply & Installation of Reception Table 1850x750x1100 (l*b*h) Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire management Secondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Drawer under counter in fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Drawer extension should be 325 MM. Drawers should have a soft closing & anti slam mechanism. Handles should be provided for ease of opening. Pedestals should be provided with lock for security. Provision and fixing for 3 set of 5/15 AMP Switch/Sockets along with 1 no. LAN Sockets should also be there including supply & provision of connector for Laptop connectivity. as per 3D view matching with Photographs as attached in RFP.

Supply & Installation of Manager Table 1250x750x770 (l*b*h) Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire management Secondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedestal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension should be 325 MM. Drawers should have a soft closing & anti slam mechanism. Handles should be provided for ease of opening. Pedestals should be provided with lock for security. Provision and fixing for 3 set of 5/15 AMP Switch/Sockets along with 1 no. LAN Sockets should also be there including supply & provision of connector for Laptop connectivity. as per 3D view matching with Photographs as attached in RFP

Supply & Installation of Center unit for Sofa Overall Size :Radius: 2' Height : 20"TABLE METERIALS & SIZE :TOP:Glass top with accessories LEGS:SS Finish. Rest detailing as per sketch/drawing matching with as per 3D view matching with Photographs as attached in RFP

Supply and Installation of Conference Table size 10'*4' table and 30" height with laminate finish and leg to be box section MS powder coated. Design and detailing to be engineer in charge.Provision for 3 set of 5/15 AMP Switch/Sockets along with 1 no. LAN Sockets should also be there including supply & provision of connector for Laptop connectivity.

Supply and Installation of credenza: structure made up of 18 mm thick Prelaminated partricle board with 2mm thick PVC edge banding tape.Approx. dimension 1200(w)*450(D)*1200(H).

Supply & installation of Manual Roller blinds having Aluminum Roller tube along with fabric pasted on it with glue having control unit for manual operations and bottom bar Aluminum powder coated for weight purpose, including fabric, fitting & accessories of approved make & colour etc. complete.

Providing and fixing pufee of size 20"*20"*18" with wooden base and with upholsetry as per attached detailing. Fabric to be pre approved from engineer in charge

Providing and fixing graffiti (hand paint Modern abstract)Design and detailing as per engineer in charge. Please refer reference image

Ceramic writing board with 25 X 40 beechwood/ approved beading on 12mm ply - size 2400 x 1200

Providing and fixing hoardings outside the building as per size give by engineer in chargeApprox. Dimensions:1200mm(W) X 900mm(H) with provision of backlight.

Providing and fixing of in reception made up of laser cut Anti-Corrosive high grade AISI 316 Stainless Steel size 1mtr by 1mtr .details given by engineer in charge.

Providing and fixing Name plate for individual cabin and rest of the area. Signage's are made up of laser cut Anti-Corrosive high grade AISI 316 Stainless Steel of 2mm thick sheet with laser cut method for impression and with satin finish. Approx. Dimensions: 300 mm X 170 mm X 2 mm.Design and detailing provided by as per engineer in charge

Electrical (providing and fixing of following items)

Wiring of light point/ fan point/ exhaust fan point/ call bell point as per specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit & it's all accessories( J.B. , Bends etc.) , round tiles,18 SWG Hot Dipped Galvanized Modular Box with earth terminal, 6 A Modular switch, Modular face plate with grid plate, 3 pin ceiling rose / lamp Holder/ 3 pin connector , screws etc, making connections,all as per pre approved by Engineer in charge, testing etc. complete as required as per recommended makes of RFP.

Short point (up to 3 mtr.)

Medium point (up to 6 mtr.)

Long point (up to 10 mtr..)

Wiring of 3/5 pin 6 amp. Light plug point as per specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit & it's all accessories( J.B. , Bends etc.) , round tiles, 18 SWG Hot Dipped Galvanized Modular Box with earth terminal, 6 A modular switch, 3/ 5 pin 6 A modular socket, Modular face plate with grid plate, screws etc,all as per pre approved by Engineer in charge, making connections, testing etc. complete as required as per recommended makes of RFP .

On board

Short point (up to 3 mtr.)

Medium point (up to 6 mtr.)

P & F 3 Way, 4 Conductors with current rating 16 Amp. Connector

S&F following sizes of ISI marked DLP U-PVC mini trunking systems along with accessories like end cap, internal angle, external angle ,Flat angle, Flat junction etc. on surface with screws, expansion fasteners as required. (make: legrand)

Mini-Trunking -32 x 12 mm

Finishing Accessories

End cap right or left

Changeable internal-external angle from 600 to 1200

Changeable flat angle from 850 to 950

Flat junction

White 32 x 10/12.5 cover joint

S&F following sizes (dia.) of ISI marked MMS ( IS:9537 P - III ) vergin material PVC conduit as per specification for electrical Works along with its accessories (IS: 3419 ) as required in recess including cutting the wall, covering conduit and making good the same as required as per recommended makes of RFP .

Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC 60228 for lower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4, , in existing surface or recessed PVC/ MS conduit/casing capping including all as per pre approved by Engineer in charge,making connections, etc. as require as per recommended makes of RFP.

3x 1.5 sq.mm

2 x 2.5 sq. mm. + 1x1.5sqmm

2 x 4.0 sq. mm. + 1 x 2.5 sq. mm.

2 x 6.0 sq. mm. + 1 x 2.5 sq. mm.

4 x 10.0 sq.mm

Supplying and fixing of power plug point with Modular accessories as per specification for electrical Works, on hot dipped galvanized modular box of 18 SWG with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost of ISI marked modular 16 amp. Switch (IS :3854) and 3/5 pin 16 amp. socket outlet (IS:1293) , making connection , testing , etc. as required. All as per pre approved by Engineer in charge, as per recommended makes of RFP.

Providing & Fixing of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load and site requirement) 4KV impulse withstand voltage, as per specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , IP 20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A rating including making connections, testing etc. as required. All as per pre approved by Engineer in charge, as per recommended makes of RFP .

Single pole MCB

6 A to 32 A rating

Double pole MCB

40 A to 63 A rating

Four pole MCB

40 A rating

50-63 A rating

Providing & Fixing of 240/415 V Residual current circuit breaker (RCCB) as per specification for electrical Works with ISI marked (IS:12640-1) / conforming to IEC 61008 -1 , rated conditional s/c current of 10 KA, truly current operated and shall operate on CBCT mechanisum, provision for pad lock, min. operation 10,000 upto 63 A rating and 5000 for 100 A rating, minimum phase termination capacity of 50 sq.mm. rigid wire , IP 20 contact protection with existing distribution board / sheet including making connections, testing etc. as required. All as per pre approved by Engineer in charge, as per recommended makes of RFP .

Two pole 100/300mA sensitivity

40 A rating

Four pole 100/300 mA sensitivity

40 A rating

63 A rating

SITC of wall/ free standing floor mounted dust and vermin proof compartmentalised cubical panel as per specification for electrical Works, made out of CRCA sheet . Other parameters required as per point (a) ,(b), (c),(d) below:- (a)Thickness of sheet shall not be less than 1.6 mm up to 600 mm length / width of any compartment and be of 2.0 mm above 600 mm. Load bearing structure shall be of 2.0 mm thick sheet supported by base M.S. channel if required . Side walls and cable alley compartments having bolted type doors with / without detachable extension type structure (b)panel shall be duly treated for derusting in 7 tank process with dephosphating and with powder coating of minimum 70 microns on both side of panel in desired shade The panel having PU/ Neoprene rubber gasket of not less than 3mm thickness ,required hardware, separate detachable gland plate M.S. base channel (min75mm) , hinged door with locking arrangement for equipment/switchgear [c) Interconnection between bus bar and switchgears /cable shall be rigidly supported and made out by flexible copper wires (up to 125 amp ) and by solid bus bar (>125 amp ) . All joints / interconnections of copper bus bar shall be dully tinned . Clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar Bus bar is insulated by Heat Shrinkable sleeves . Earth and Neutral bus bar shall be half of the size of phase bus bar. (d) only outer area on all sides shall be measured & panel to be fabricated only from CPRI approved fabricator. All as per drawing pre approved by Engineer in charge. as per recommended makes of RFP .

Supplying and fixing of Aluminium (IEC 60105 ISO 209-1,2) / Copper (IEC 60028) bus bar as per specification for electrical Works, by means of SMC / DMC type insulator, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable PVC sleeves. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Electrolytic grade Aluminium bus bar 6010 grade

Providing & Fixing of BIS approved Current Transformer as per specification for electrical Works ,ISI marked as per IS 2705-1992/ conforming to IEC 60044-1, with secondary terminal of CT shall be brought out suitable to a terminal block which shall be easier accessible for testing and terminal connection , with all necessary support in existing panel including connection etc. as required Current transformer Resin Cast Wound Primary / Ring Type Tape Wound as per IS 16227 with, Accuracy Cl, CT ratio and burden as specified. ISF<=5, Cu cross section of secondary wire 1.5sqmm (minimum), including all necessary support in existing panel including connection etc. as required . All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

C T Class 1, Ratio upto 150/5, Burden 5 VA

Providing & Fixing of ISO certified company made UL listed , IP 65 110/220 V, unibody LED Indicating lamp IEC 60947 , CSA 22.2 with integral circuit, IP 20 terminal block, Approx. body dia for panel not less then 20 mm, length min. 50mm, front LED cover dia min. 29 mm, contact material phospher bronze for Led, PCB contacts shall be of brass (tin plated), impulse dielectric tested for 2.5 KV, Rated insulation resistance shall be 100 M ohm at 500VDC including connection etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Red/yellow/Green colour

Providing & Fixing of IP 51 Multi function meter as per specification for electrical Works, ISI marked (IS 16444)/ Confirming to IEC 61557 & IEC 62052 with LCD/ LED 3/4 line display capable of measuring electrical parameters like V, I, F, PF, KW, Kva, Kvar, Kwh, Kvah, Kvarh display with 1A/5A CT input for LV/ HV network, with /without RS 485 communication port etc. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP . Multifunction LCD meter with V, I, F, PF, KW, Kva, Kvar, Kwh, Kvah, Kvarh, Run hours, On hours, Phase angle, Interrupts, THD, Events, Neutral Current class 1 accuracy with RS485 port.

Providing & Fixing of recessed/surface mounting heavy duty sheet steel 1.6 mm thick End Box as per specification for electrical Works for distribution board duly phophatised powder coated complete as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

For TPN 4 Way

For TPN 6 Way

For SPN 12 Way

Providing & Fixing of following modular accessories as per specification for electrical Works, made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , minimum width of 1 module switch toggle( PUSH PART ) should not less then 20mm, including all as per pre approved by Engineer in charge,making connections, testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Blanking plate

Providing & Fixing of ISO certified company made vergin material PVC trunking system as per specification for electrical Works, with double lock feature for cable management including finishing accessories like corners, tee, adjustable angles, junction etc. as required . The trunking system shall have adaptable system for modular type RJ 45 data socket/ wiring accessories/ power sockets and shall be covered with peal off plastic cover. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

80mm x 50mm

SITC of chemical Gel earthing system of Dual Pipe Technology made of with "B" Class G I Pipe as per IS 1239 ( part-1):2004 of Medium duty of following sizes as per points mentioned (a), (b), [c), (d), (e) below :- (a) filled with anti corrosive conductive compounds with the permanent sealings at both the ends, CPRI/ ERDA tested with RMS capacity of minimum 35- 40 KA for withstanding 1 second . (b) To ensure the moisture content and electrical conductivity, 25 kg for 2000 mm & 50 Kgs for 3000mm of resistance lowering earth enhancement material shall be used as a backfill compound. The compound shall be tested form NABL acredeated lab for low resistivity ( less than 0.12 Ohm - meter) & high conductivity in nature with carbon as a major content as per referance of IS 3043-1987,IEEE 80-2013 (clause 14.5d) , IEEE 837 & IER 1956 with latest amendemnts ©Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. (d) Testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book. (e) All as per pre approved by Engineer in charge as per recommended makes of RFP

With Pipe in Pipe Technology (Outer pipe dia. / Inner pipe dia. ) Minimum 100 mm dia borewell

GI pipe 3000 mm long, 80 / 50 mm, Terminal 50 mm x 6 mm GI Strip

Supply & Laying following size earth strip in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, Jointing shall be done by overlapping and with 2 set of Brass (for Cu strip) / GI (for GI Strip) nut bolt & spring washer spaced at 50cm making connection etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

25mm x 3mm copper strip

Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with GI/Cu thimble etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

8 SWG copper Wire

Supply & fabrication steel structure with MS channel / angle / joist / ISMB / sheet etc. including welding, rivetting, cutting, nut & bolt , one coat of primer & two coat of enamel paint etc. as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

SITC of IP 40 quick make and quick break 4 pole current limiting Moulded case circuit breaker (MCCB) made of flame retardent & heat resistant material having following current rating, short circuit breaking capacity at 440/415 V, 50 Hz; O/L & S/C settings as per specification for electrical Works, conforming to IS/IEC 60947 P -2 :2003 with front face and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push (test) to trip, trip time less then 10 ms under s/c condition, Breaking capacity Ics = 100% Icu. U imp =8 KV, rated insulation voltage 800 V, provision for UVR , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connections with lugs & spreaders, etc. as required. All as per pre approved by Engineer in charge. as per recommended makes of RFP .

With Thermal Magnetic release

up to 100 Amp , 25 kA, adjustable O/L & fixed S/C setting, Ics = 100 % Icu

Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-armoured / Armoured aluminium cable of 1.1 KV grade as per specification for electrical Works in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench with filling of excavated earth in trench , on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points (a), (b), (c), mentioned below:- (a) Material :- H4- Grade aluminium conductor of purity >99.6 % & as per IS:1554 P-I / IS :7098 P - I (b) conductor shall have electrolytic aluminium confirming to IS 8130, IS 3975-1999 for armouring of cables in armoured cable items , IS 5831 for sheath, IS 10810 (Part 0 to 64 ) for testing procedures . (c) All above as per pre approved by Engineer in charge and as per recommended makes of RFP .

Armoured Cable

Supplying and making one end termination with heavy duty brass compression gland (as per IS 12943- 1990) SIBG type, heavy duty aluminium lugs (as per IS 8309 -1993 & IS 8337-1976 ) duly crimped with crimping tool, PVC tape as per specification for electrical Works etc for following size of Armoured PVC insulated & PVC sheathed/ XLPE aluminium conductor cable of 1100 volt grade as required of size. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

4 x 16.0 sq.mm

3.5 x 35.0 sq.mm

Providing & Fixing of IP40 LED Surface/ Recessed / suspended mounting Mid power SMD type LED Light fixture made from CRCA sheet steel housing, high purity / transmisivity UV stabilized Non -yellowish diffuser for uniform light distribution. High efficiency with 2.5 KV internal/external surge protection BIS certified isolated driver having efficiency > 85% , with Short & Open circuit protection and in compliance to IEC standards (Integral with light fixture). System lumen efficacy of ≥ 120 lm/Watt ,THD < 10 % , p.f.≥0.95,CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. All as per pre approved by engineer in charge .as per recommended makes of RFP .

48W LED light fixture 2'x2' with acrylic / prismatic front cover.

Providing & Fixing of IP40 LED Recessed / Surface Mounted, Round / Sqaure Non-Dimmable Back lit SMD Mid Power LED Downlight with die-cast aluminum housing & Heat Sink for heat dissipation with UV Stabilized non yellowish Diffuser with internal/ external BIS complience 2.5 KV surge protected Isolated driver, with Short & Open circuit protection, having efficiency > 85% and in compliance to IEC standards. System Lumen efficacy of ≥ 120 lm / watt, THD < 10 % ,p.f.≥0.95, CRI >80, life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.as per recommended makes of RFP .

Recessed Mounting

LED Downlight 18/20W

Supply & Laying following size' B ' class , Medium class G.I. Pipe confirming to IS : 1239 P - 1 ( 2004 ) with accessories like bend, socket etc. for laying earth conductor/ strip / cable in ground/ surface/ recess as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

32mm dia

Supply, Fabricating & installing following sizes of powder coated perforated M.S. cable trays with perforation not more then 17.5% in convenient section including horizontal and vertical bends, reducers tees,cross members and other accessories as required and duly suspended from the ceiling with MS suspenders including bolts & nuts , fastners, supports, painting suspenders etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

150mm x 50mm x 1.6mm

300mm x 62.5mm x 2.0mm

Supply & Fixing of ABC Type (MAP 50) type powder Fire Extinguisher (Stored Pressure type) of following capacity duly current and valid BIS certification conforming to IS: 15683:2006, with Dry chemical powder used as extinguishing agent should be Mono Ammonium Phosphate 50% concentration conforming to IS 14609:1999. Serial no. and date of manufacturing should be embossed or printed on the body of the fire extinguisher. The firm should submit the product certificate from an EN notified body & product performance test report from NABL accredited Lab as per IS 15683. . All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Providing & Fixing of of M.S. J- hook of standard design made out of 16 mm dia. M.S. round bar and fixed with cement concrete mortar with required support as required.

Providing & Fixing of ISO Certified company made BEE Approved copper wounded 1200 mm sweep BLDC technology power saving ceiling fan with longer life span and low maintenance 5 star rated which can withstand on votage fluctuations from 140 volts to 240 volts ,power factor not less then 0.9 , service value (CMM/W) minimun 6.85 , air delivery minimun 215 CMM, speed 350 RPM ( tolerance as per IS:374 2019 ) THD less then 10% and complete with down rod up to 30 cm with secondary support safety cable , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Without Remote

Providing & Fixing of heavy duty, copper wound , Double ball bearing and with metal sturdy mesh guard; Aluminium alloy one piece blade wall mounting oscillating type air circulator as per specification for electrical Works, conforming to IS:2997, including fixing with anchor bolts, regulator making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

450 mm sweep With wall Mounting and three speed regulator

SITC of raceway confirming to EN 50 085-2-2, IP-20, IK-08 for distributing cablling for screed floora installation & particularly suitable for applications requiring EMC screening material/GI raceways made up of pregalvanized sheet (DX51D-Z120 MAC) in desired color, non corrosive, non flame propagation, with 2 to 2.5 mtr, standard length/standard depth 25mm / 38mm, thickness 1.6 mm for raceways, 1.0 mm for partition with coupler for joining raceways including making jhiris on floors/wall if required of following sizes. Make: legrand / MK

SITC of GI junction box with removable precuts knockouts provided for raceways resistance to vertical load over a small area, 500N and for large surface area 2000N with adjustable height 50 to 70mm with flyover as required . Make: legrand/MK

SITC of 10 KVA 3 Phase Input, 1 Phase Output advance DSP controlled UPS with IGBT based rectifier, LCD display, double conversion / Digital Signal Processing UPS, with isolation transformer, with 30 minute battery back up, with required cabling for incoming & outgoing connection (Approved makes: Emerson / Numeric / APC)

Technical Specification: Phase: 3 Pahse in /1 Phase out Capacity : 10000 VA /9000 W Input Characteristics : Nominal Voltage : 3 X 400 VAC (3 Ph +N) Voltage Range: 305-478 VAC(3-Phase) @ 100% Load Frequency Range: 46~54 Hz or 56~64 Hz Power Factor - >= 0.99 @ 100% Load THDi : < 6% @ 100 % load

OUTPUT Characteristics : Output Voltage : 208/220/230/240 VAC AC Voltage Regulation (Batt, Mode) : ± 1 % Frequency Range (Synchronized Range) : 46~54 Hz or 56~64 Hz Frequency Range (Batt. Mode) : 50 Hz ± 0.1 Hz or 60 Hz ± 0.1 Hz Current Crest Ratio : 3:1 (max.) Harmonic Distortion : ≤ 2% THD(Linear Load) ; ≤ 5 % THD (Non- Linear Load) Transfer Time (AC Mode to Battery Mode): Zero Transfer Time (Inverter to Bypass) :Zero Waveform (Batt. Mode) : Pure Sinewave AC mode Efficiency : ˃ 92% ECO Mode Efficiency : 97 %

BATTERY Characteristics : Battery Type : SMF or Tubular Battery Nos. : 20 Charging Current (Max.) : 12 A settable to 2/4/6/8/10/12 Amps Charging Voltage: 273 VDC ± 1 % (Based on 20 pcs batteries)

Indicators: LCD Panel : UPS status , Load level, Battery level, input/output voltage, Discharge Timer and Fault Conditions

Alarm: Battery Mode : Sounding every 4 seconds Low Battry : sounding every second Overload : sounding twice every second Fault : continuously sounding

10 KVA 3 Phase Input, 1 Phase Output

LAN Services:

Supply , Installation, Testing and Comissioning of Wall mounted Communication rack with glass doors, handles ,lock , Top and Bottom Cable entries, Supports for mounting rack on wall , Cable managers, one Fan, Equipment mounting hardware, power supply box for supplying power to switches, fans etc along with earth continuity kit, Mcb, indicator, moulded power supply cable

12 U(44 mm ) wall mounted

Supply, Installation, & Testing of 19" 1U Rack Mounted/ surface mounted aluminum/ CRCA 1.2mm powder coated, multimode glass Fiber Optic Cable Patch panel/LIU loaded with flangless/screwable adapters for ST/E-2000/SC/LC/MT-RJ/PC type, It should have easy removable Top plate with push buttons, there should be a splice tray installed in the Patch panel/LIU which can handle the fiber cores, splice tray should be PC+ABS material, it should include accessories like mounting hardware, gormetts, heat shrink tubes/sleevs, screws, nuts to install the panel for rack/wallmount applications as per requirement complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Multi Mode LIU 6 Ports

Supply, Installation, & Testing of Indoor duplex Multimode patch cord (50/125 µm made of glass fiber optic with LSZH jacket, Multimode G652.D Mounted on both sides with ST/E-2000/SC/LC/MT-RJ/PC type Duplex connectors in acc. with IEC 61754-20 as per latest ammendments of TIA/EIA 569B.3, as per requirements complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Supply, Installation, OTDR Testing & Fusion Splicing of Fiber Multimode Pigtail (50/125 µm) made of glass fiber optic, should be fitted at one end with any one type of single ST/E-2000/SC/LC/MT-RJ/PC type connector in acc. with IEC 61754-20, as per latest ammendments of TIA/EIA 569 Standard Specification as per requirments complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Supply, Drawing and Testing, of stranded Multi mode (50/125 µm) glass optic fiber cable, as per latest ammendments of TIA/EIA 568/ISO/IEC 11801:2011/ IEC 60794-1-2 E1, E3,E11, F1/ EN 50173-1/ EN 187 000/ IEC 60974-2, 2-20, 2-21/ ITU G.652D, construction of LSZH outer sheath cable, cable should be used for LAN and WAN back bones, . With its LSZH sheathing these cables should be ideal for indoor/outdoor installations in existing MS/PVC /HDPE Conduits/ slotted channels with ferruling at both ends for identification complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

6 core 10G fiber cable

Supply , Installation and Testing of 4 pair, 100 Ohm impedance, Cat 6/6A patch cords should be constructed of minimum 23/24 AWG, stranded bare Copper cable with FRPVC/LSZH Jacket, with an enhanced performance by factory moulded RJ45 connectors as per ANSI/TIA/EIA 568 suitable for Cat 6/6A application complying to latest ammendments Category 6/6A Standards, According. to TIA568, minimum requirement for 1G BASE-T/ 10G BASE-T performance. Patch cords shall be straight thru cable compatible with both T568-A and T568-B wiring schemes, Minimum 750 to 1000 mating cycles in plug contacts for long durability complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Cat 6, UTP (Un-sheilded Twisted Pair) Patch Cord

Supply, Installation, Testing and Comissioning of Rack mounted 19" 1U, 24 Port Unloaded, 1.5-1.6 MM CRS chasis, powder coated, sheet steel, made of plastic (ABS), Modular Patch Panels (without I.O.) with Rear Cable management system and mounting hardware to mount the patch panel. Should have port identification numbers printed/engraved on front of the panel, . There should be a provision for each port/jack on the panel and reusable removable on field from the panel complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

SITC of Intelligent Ethernet POE Switches providing 24 x 10/100/1000 Fast Ethernet POE ports- 370W or better and 4 dual purpose uplink (provision for Copper / Fiber Giga connectivity) with provision of minimum Stacking of 06 Switches with related LAN Base Software . For additional technical parameters of products/ work as per recommended makes of RFP.

Supply, Installation, Testing and Comissioning of Rack mounted , 48 x 10/100/1000 Ethernet ports Gigabit Switch with 4 mini Gigabit Interface Converter slots(shared with 4 Ethernet ports) for Gigabit Ethernet expansion , Switching capacity 96 Gbps nonblocking , . As per recommended makes of RFP.

Supply, Installation, Testing and Comissioning of 1G SFP (small form-factor pluggable) transceivers as per recommended makes of RFP.

Supply, Installation, Testing and Comissioning of 10G SFP (small form-factor pluggable) transceivers as per recommended makes of RFP.

Supply, Drawing and Testing of 4 pair, 23 AWG Solid Bare Copper wire insulated with PVC, UTP (Unshielded Twisted Pair), Category 6, Class E, 100 Ohm Impedance, Indoor Cable as per latest ammendments of ANSI/TIA/EIA-568 , The copper conductors should be balanced twisted in pairs, seperated by a cross-member fluted pair divider & protected by PVC Jacket. Certified performance in a 4-connector configuration upto 100 Mtrs channel requirements & transmission frequencies up to 250 Mhz. in existing MS/PVC Conduits/casing capping including making connections to Information outlets and Patch Panels with jack & ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Supply and Installation of unsheilded/ sheilded Information outlets made of high impact plastic body with ABS, FR Grade with provision for protection against dust in jack/ FP, suitable for Cat 6/6A application complying to latest ammendments, According. to Cat. 6/6A channel, It should support channel as well as components requirements of Cat.6/6A standards at frequencies of up to 250 to 500 Mhz. Cat 6/6A unshielded/shielded Jack should be suitable to terminate 4 pair, 23/24 AWG solid/stranded wire diameters, using 100 Ohm unshielded/shielded balance twisted pair cable, the jack should have tooless/impact punch termination on reliable copper tin plated Insulation displacement contact, It complied with ANSI/TIA/EIA 568 standard. In existing modular/MS Boxes along with necessory connections as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Cat 6, Un-sheilded Information Outlet

Supply & fixing of square Faceplate for Flush / Surface Mount Information Outlets Single/Dual or Quad Aperture , material should be PC+ABS body, Suitable for RJ45 unshielded/shielded connection modules. Should match with I. O. . Dimensions should be 86mm X 86mm as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer recommended makes of RFP .

Single Aperture

SITC of Workstation latest Intel® i5 processor, Intel Chipset motherboard, 08 GB RAM, 1 TB SATA HDD at 7200 rpm, with 4GB GPU type higher end Graphic card for H.265 compression technique with dual display ports/DVI/ HDMI port, Giga LAN Card, wireless Keyboard, wireless optical Mouse, (Approved Makes: Dell, HP, Lenevo)

SITC of 5 MP IR Fixed Dome Network Camera -1/2.7 inch Progressive Scan CMOS, 2592 × 1944 at 25fps, 2.8 mm Fixed lens, 0.003 Lux at F1.4, 0 Lux with IR on, ICR, ONVIF (PROFILE S, PROFILE G, PROFILE T), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, BLC, HLC, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 256 GB (SD card not included), IP67, IK10, Edge Analytics- Line crossing detection, Intrusion detection, Motion detection, Region entrance detection, Region exiting detection, Scene change detection, Face capture, Video tampering, audio exception detection, False alarm reduction through human and vehicle target classification based on deep learning UL, CE, FCC certified.Approved brand:- Pelco, Prama, Axis, hikvision

SITC of 32 Ch Smart Network Video Recorder : Connect Up to 32 IP Cameras, Dual OS, Up to 12 Megapixels Resolution, 2 HDMI at least 1 HDMI 4K, 2 VGA atleast 1 VGA 2MP Output , Support H.265, MJPEG, Incoming Bandwidth 320Mbps, 8 SATA Hard Disks, ANR Technology, 8 SATA interfaces for 8 HDDs and capacity of each HDD upto 6TB, 3 × USB 2.0 at least 1 USB with 3.0, Alarm I/O 16/4, RS-485, RS-232, 2 RJ-45 10 /100/1000 Mbps self-adaptive Ethernet interface,two 8 tb hardisk included, Multiple network monitoring: Web viewer, CE, FCC, UL certified.Approved brand:- Pelco, Prama, Axis, hikvision

providing and fixing Interactive Display65' with mounting kit Approved Makes:- Hikvision, samsung, Sony

Fire Services:

Supplying and drawing FRLS PVC insulated & unsheathed flexible copper conductor as per specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC 60228. FRLS PVC insulation which provides better fire retardant properties then normal PVC & also emits Low Smoke in case of fire & use type A insulation PVC, in existing conduit including , all as per pre approved by Engineer in charge,making connections, etc. as required. For additional technical parameters of products/ work refer recommended makes of RFP .

2 x 1.5 sq.mm

SITC Conventional Optical type Smoke Detector with mounting base, LED etc. as required.

SITC of conventional type Manual call point complete with Glass, hammer and chain etc. as required.

SITC 6 watt Speaker mounted in M S sheet box with perforated front mesh for PA and Emergency System.

SITC of wall / floor type following zone (each zone accessing minimum 20 units (detectors/ devices ) Conventional Type microprocessor based with LCD display main control panel/ floor panel fabricated from 16 SWG CRCA sheet steel sealed maintenance free (SMF) batteries of min2X7AH of 12 V or as required.

Specification: (i) Three Form-C relays (1 Fire, 1 Fault and 1 Fire/Fault 2 Amps@30VDC (ii) 1 On-board NACs operating @ 0.5 A/circuit (iii) Aux Output : 24 VDC (iv) Sounder Output : 24 VDC (v) Feature Detection Circuits: 4 Zones ( upto 20 Detectors + 5 MCPs) (vi) Zone wise Fire, Fault , Disable indication (vii)Panel keys : Silence Buzzer/ Alarm, Reset, Navigation keys (Left, Right, Down, Menu/Ok) (viii) Lamp Test & Walk Test (ix) Standby power 24V DC (2 no's of 12V, 7Ah Lead Acid Battery) (x)Certification (CE, LVDE) (xi) Event Log- 1200 events (xii) Earth fault monitoring

User Interface: Display: 16 X 2 character LCD Control Keys: Menu/Ok, Silence, Navigation and Reset buttons Indicators: Fire, Power, Fault, NAC Fault, Earth Fault, Silence

Wiring Details: Mechanical Specifications : Construction: Cold Rolled Steel with powder coated finish with door lock Cable Entry : 08 Number x 20.50 mm knockout Electrical Specifications: Operating Voltage: 230 VAC, 50 HZ Alarm Load(Sounder) 0.5 A (max) NAC output 0.5Amp.(max) Operating Temperature : 0oC~ 49oC Relative Humidity : 5 % to 95 % non -condensing Standby Batteries : Minimum capacity (2 X12 V 2.8 Ah); Maximum Capacity (2 x 12 V 7 Ah) Detection Circuits : 2,4,zone , max 2 mA per detector class B circuit External outputs : sounder output (18.5 to 28.0 Vdc, 0.5 Amp.(max)); Auxiliary Output ( 18.5 to 28.0 Vdc, 0.5 Amp.(max))

Compatible Devices: System sensor Photo Electric Smoke Detector, System sensor Photo Electric and Heat detector, System sensor Plug-in detector base System sensor MCP Red W/O Back Box System sensor Horn cum strobe , wall , Red, Standard Candela

HVAC Services

SITC of Air Cooled split type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (EP foam pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 4 Mtr (IDU to ODU), R-22/R-410 Refrigerant, Remote, suitable for 400/230V +10% of 50 Hz ,1 /3 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / reciprocating / rotary compressor as specified.

Hi Wall/Ceiling Wall Split

1.0 TR with 5 star rating of BEE

1.5 TR with 5 star rating of BEE

2.0 TR with 5 star rating of BEE

SITC of Air Cooled Cassette type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (EP foam pipe section) upto 10 Mtr (IDU to ODU), copper power cable upto 10 Mtr (IDU to ODU), R-22 Refrigerant, wireless Remote, drain pump,suitable for 400/230V +10% of 50 Hz ,1 /3 phase AC supply capable of performing cooling, dehumidification, Air circulation, filteration & ventilation of following capacity with Scroll / reciprocating / rotary compressor as specified.

SITC of Interconnecting refrigerant pipe work with closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications including chase cutting, supports etc. as required.

Providing and fixing of cPVC drain water piping complete with fittings, support with MS hanger as per specification and insulated with 6 mm thick closed cell elastomeric nitrile rubber insulation. Make: cPVC Pipe -Supreme / Astral / Kisan. Insulation - Armaflex / Supreme/ Superlon / Aflex /Kflex.

32 mm dia O.D

25 mm dia O.D

Making hole in stone masonary/ RCC wall/ RCC slab with core cutter for accomodating refrigerant pipe/ drain pipe/ MS pipe/ cables etc of following dia

150 mm dia per running inch length

Water Purifier

Providing and fixing Kent or Equivalent water fountain chillar cum inbuilt RO water purifier with cooling capacity 30 Ltr per hour@ 14-22 degree C and no of faciets to be 2 (1 cold+ 1 normal)

Eminent Colonizers Private Limited

Eminent Colonizers Private Limited

Eminent Colonizers Private Limited