SPL REPAIR REPLACEMENT OF EXTERNAL ELECTRIC SUPPLY INCLUDING SEGREGATION OF POWER SUPPLY WITH CHANGE LEVER FOR OFFICE MD ACCN TRANSIT ACCN AND PL LINES SPL REPAIRS TO PARAPET WALL RAILING STAIR CASE INCL E/M WORKS FOR 02XQTRS OF BLDG NO P10 OF ORs MD

Supply, laying, jointing & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor, 1100 volts grade, of following sizes complete all as specified and directed.

3.5 core x 185 Sqmm

3.5 core x 120 Sqmm

3.5 core x 95 Sqmm

3.5 core x 70 Sqmm

3.5 core x 50 Sqmm

3.5 core x 35 Sqmm

S&F for 50mm dia GI pipe 'light grade' ISI marked including fittings such as bends, sockets etc fixed on wall/pole or laid in trenches under road crossing/hardstanding including taking down existing pipe complete all as specified and directed.

M&L Sand cushioning with dry local sand for cable protecting of under ground cable (8 cm before laying the cable and 15 cm after laying the cable) in trenches including punning the sand upto 18 cm thick and consolidated complete all as specified and directed. Note: Sand thickness shall be measured after punned down for payment purposes.

Supply and laying dry well burnt locally available bricks sub class'B' old size laid flat with width equal to the length of whole bricks over cable as cable protection complete all as spcified and directed

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm each complete all as specified and directed.

Excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes,laying of cables etc. not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Removal of surplus excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

Supply, fabrication, installation and testing of LT Panel out door type factory made CPRI Approved, water and vermin proof protection of suitable size as per IS specification made out of 3.15 mm thick outdoor type CRCA sheet dully supported with mild steel angle iron of size 40 x 40 x 5 mm vertical frame and legs with mild steel flat iron 40 x 40 x 5 mm in horizontal sides of the frame with front and back side openable ,single hinged door / shutter with locking arrengement and powder coated finish both internal and external steel surfaces after necessary preparation of steel surfaces including providing PCC (1:3:6) type C2 foundation of suitable size and connections of all outgoing / incomming cable inclusive of necessary excavation and earthwork as required including the following fitment accessories and also including removing old exisisting one complete all as specified and as directed. Note: Rate of earthwork and PCC work are deemed to be inclusive in this item.

INCOMMING

Copper strip busbar of 400 amps rated capaacity wrapped with PVC sleeves with maintained the colour code and provision of making holes with Copper nuts, bolts & washers for cable connections including hydrograpic insulators with nuts & bolts at both ends = 04 Nos

4 pole MCCB 200 Amps , adjustable thermal magnetic release type 415 Volts, Ics = 100% Icu, breaking capacity 25 KA including all fixing accessories with both ends spreader links - 01 No.

LED Neon indicator lamp (RYB), 230/250 volts, AC -01 set (set of three) Make :- Legrand/L&T/Schneider.

OUTGOING

4 Pole MCCB 200 Amps, adjustable thermal magnetic release type, 4 poles, 415 Volts, Ics = 100% Icu, 25 KA breaking capacity including all fixing accessories with both ends spreader links -01 No (For FPB to P-7 & P-8 bldg)

4 Pole MCCB 160 Amps, adjustable thermal magnetic release type, 4 pole, 415 Volts, Ics = 100% Icu, 25 KA breaking capacity including all fixing accessories with both ends spreader links -02 Nos (For FPB to P-9 & P-10 Bldg & Spare)

MCB TPN 32 Amps C series, adjustable thermal magnetic release type, 4 poles, 415 Volts, Ics = 100% Icu, 10 KA breaking capacity including all fixing accessories with both ends spreader links -01 No(Spare)

MCB SPN 20 Amps, 10 KA breaking capacity, C-series including all fixing accessories with lugs -01 No (Spare)

Enamelled iron danger notice plate of 1.60 mm thick mild steel sheet of size 200 mm X 150mm , white with letters , figures and conventional skull and bones in signal red and fixed with nuts and bolts on door / shutter of JB for LT -01 No.

Supply, fabrication, installation and testing of LT Panel out door type factory made CPRI Approved, water and vermin proof protection of suitable size as per IS specification made out of 3.15 mm thick outdoor type CRCA sheet dully supported with mild steel angle iron of size 40 x 40 x 5 mm vertical frame and legs with mild steel flat iron 40 x 40 x 5 mm in horizontal sides of the frame with front and back side openable ,single hinged door / shutter with locking arrengement and powder coated finish both internal and external steel surfaces after necessary preparation of steel surfaces including providing PCC (1:3:6) type C2 foundation of suitable size and connections of all outgoing / incomming cable inclusive of necessary excavation and earthwork as required including the following fitment accessories and also including removing old exisisting one complete all as specified and as directed. Note: Rate of earthwork and PCC work are deemed to be inclusive in this item.

INCOMMING

Copper strip busbar of 300 amps rated capaacity wrapped with PVC sleeves with maintained the colour code and provision of making holes with Copper nuts, bolts & washers for cable connections including hydrograpic insulators with nuts & bolts at both ends = 04 Nos

4 pole MCCB 200 Amps, adjustable thermal magnetic release type 415 Volts, Ics = 100% Icu, breaking capacity 25 KA including all fixing accessories with both ends spreader links - 01 No.

LED Neon indicator lamp (RYB), 230/250 volts, AC -01 set (set of three) Make :- Legrand/L&T/Schneider.

OUTGOING

4 Pole MCCB 125 Amps , adjustable thermal magnetic release type, 4 poles, 415 Volts, Ics = 100% Icu, 25 KA breaking capacity including all fixing accessories with both ends spreader links -01 No (For O/G P-7 Bldg Power point)

4 Pole MCCB 100 Amps, adjustable thermal magnetic release type, 4 pole, 415 Volts, Ics = 100% Icu, 25 KA breaking capacity including all fixing accessories with both ends spreader links -03 Nos ( For O/G P-7 Bldg light point-01 No, O/G P-8 Bldg power point-01 No, Spare-01 No)

4 Pole MCCB 63 Amps, adjustable thermal magnetic release type, 4 pole, 415 Volts, Ics = 100% Icu, 18 KA breaking capacity including all fixing accessories with both ends spreader links -02 Nos ( For O/G P-8 Bldg light point-01 No, Spare-01 No)

ON load Change over switch 100 Amps, 4 pole,415 Volts including all fixing accessories with both ends spreader links-01 No (For P-8 Bldg Light load)

MCB TPN 20-32 Amps C series , adjustable thermal magnetic release type, 4 poles, 415 Volts, Ics = 100% Icu, 10 KA breaking capacity including all fixing accessories with both ends spreader links -02 Nos( For street light- 01 No & spare-01 No)

MCB SPN 6-32 Amps , 10 KA breaking capacity, C-series including all fixing accessories with lugs -02 Nos(Spare)

Multifunctional Digial type timer Switch (Astro type having longitude and latitude of Indian cities memory) 240 volts AC Single Phase - 01 No

Power contactor 4 Pole, 40 Amps, 415 Volts, 50 Hz - 01 No

Enamelled iron danger notice plate of 1.60 mm thick mild steel sheet of size 200 mm X 150mm , white with letters , figures and conventional skull and bones in signal red and fixed with nuts and bolts on door / shutter of JB for LT -01 No.

Supply, fabrication, installation and testing of LT Panel outdoor type factory made CPRI Approved, water and vermin proof protection of suitable size as per IS specification made out of 3.15 mm thick type CRCA sheet dully supported with mild steel angle iron of size 40 x 40 x 5 mm vertical frame and legs with mild steel flat iron 40 x 40 x 5 mm in horizontal sides of the frame with front and back side openable ,single hinged door / shutter with locking arrengement and powder coated finish both internal and external steel surfaces after necessary preparation of steel surfaces including providing PCC (1:3:6) type C2 foundation of suitable size and connections of all outgoing / incomming cable inclusive of necessary excavation and earthwork as required including the following fitment accessories and also including removing old exisisting one complete all as specified and as directed. Note: Rate of earthwork and PCC work are deemed to be inclusive in this item.

INCOMMING

Copper strip busbar of 250 amps rated capaacity wrapped with PVC sleeves with maintained the colour code and provision of making holes with Copper nuts, bolts & washers for cable connections including hydrograpic insulators with nuts & bolts at both ends = 04 Nos

4 pole MCCB 160 Amps, adjustable thermal magnetic release type 415 Volts, Ics = 100% Icu, breaking capacity 25 KA including all fixing accessories with both ends spreader links - 01 No.

LED Neon indicator lamp (RYB), 230/250 volts, AC -01 set (set of three) Make :- Legrand/L&T/Schneider.

OUTGOING

4 Pole MCCB 160 Amps, adjustable thermal magnetic release type, 4 pole, 415 Volts, Ics = 100% Icu, 25 KA breaking capacity including all fixing accessories with both ends spreader links -01 No

4 Pole MCCB 63 Amps, adjustable thermal magnetic release type, 4 pole, 415 Volts, Ics = 100% Icu, 18 KA breaking capacity including all fixing accessories with both ends spreader links -03 Nos

MCB TPN 20-32 Amps C series , adjustable thermal magnetic release type, 4 poles, 415 Volts, Ics = 100% Icu, 10 KA breaking capacity including all fixing accessories with both ends spreader links -03 Nos

MCB SPN 6-32 Amps , 10 KA breaking capacity, C-series including all fixing accessories with lugs -02 Nos

Enamelled iron danger notice plate of 1.60 mm thick mild steel sheet of size 200 mm X 150mm , white with letters , figures and conventional skull and bones in signal red and fixed with nuts and bolts on door / shutter of JB for LT -01 No.

M & L for earthing to OH/Sub stn with galvanised steel earth plate electrode of size 600 x 600 x 6 mm thick, buried directly in ground (earth pit not less than 2.25 m below normal ground level) with top edge of earth plate not less than 1.5 m below normal ground level connected to main earth lead GI earth strip 32x6 mm dia by means of bolts, nut, check nuts and washers of galvanised iron or steel all as shown in electrical plate No3 of MES Schedule of rates Part-I 2009, GI earth strip 32x6 mm protected by GI pipe 40 mm dia light grade and connected to earth test point including excavation in any type of soil, returning filling, disposal of soil, providing charcoal dust and common salt up to top edge of earth plate, construction of PCC pit with RCC cover, funnel, watering pipe of 20 mm dia GI light grade and provision of earth test point including testing on completion complete all as specified and directed.

Supply and fixing cable tray steel with cover of size 300 X 200 X 2 mm thick including all necessary fitting accessories complete all as specified and directed.

M & L for Plain Cement Concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed.

Taking down Machine pressed Precast concrete interlocking paver block of any shape & size and stacking aside for reuse complete all as specified and directed.

M & L for 20 mm thick sand layer speard uniformely over sub base complete all as specified and directed.

M & L for 60 mm thick Machine pressed precast concrete interlocking paver block of any shape and size confirming to IS 15658-2006, M-35 Grade complete all as specified and as directed. Note :- (i) The pattern of paver block shall be approved by GE Danapur.

Fixing only Machine pressed precast concrete interlocking paver block of any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement pigment complete all as specified and as directed. Note: Old retrieved serviceable paver blocks shall be used in this item.

Taking down carefully aluminium point wiring(any type)for one light point, fan point ,exhaust fan point, bell point, power point complete including all fittings such as switches, socket, pendents holder, ceiling rose, sketch fittings, tube light fittings, regulatores unscrewing the switch sockets, ceiling rose, regulators from boards/outlet boxes and making good the disturbed surfaces of wall/ ceiling and colour washing matching with the existing colour wash complete all as specified and directed.

M&L for point wiring complete with PVC insulated unsheathed, 1100 volts grade cable 1.5 Sqmm (nominal area) FRLS type multi stranded copper conductor, single core drawn in and including not less than 20 mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring for one light/fan/ exhaust fan point controlled by one, one way switch, including concealed pressed steel terminal box of required size not less than 1.0 mm thick factory made duly painted inside & outside with two coats of black bituminous paint over & including a coat of red oxide primer, with 2.8 mm thick top cover of plastic laminated sheet of required colour for mounting switch, sockets, fan regulator etc including 1.5 Sqmm FRLS type PVC insulated unsheathed cable multi-stranded copper conductor as continuous earth wire and connected to earth dolly as required at site& including chases cutting & making good disturbed surface & applying finishes to match existing surface complete all as specified and directed.

The same as item No 19 here-in-before but one 3 pin, 5amp socket out let on independent board.

The same as item No 19 here-in before but 3pin, 5amp socket out let on the same board with other switch.

The same as item No 19 here-in before but for one bell/buzzer point controlled by one bell push single pole one way .

The same as item No 19 here-in before but for one 6 pin 15/16 amps socket outlet point on an independent board with cables of size 2.50 Sqmm.

M&L for point wiring complete with PVC insulated unsheathed, 1100 volts grade cable 4.0 Sqmm (nominal area) FRLS type multi stranded copper conductor, single core drawn in and including not less than 20 mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring for one light/fan/bell/buzzer / exhaust fan point controlled by one, one way switch, including concealed pressed steel terminal box of required size not less than 1.0 mm thick factory made duly painted inside & outside with two coats of black bituminous paint over & including a coat of red oxide primer, with 2.8 mm thick top cover of plastic laminated sheet of required colour for mounting switch, sockets, fan regulator etc including 4 Sqmm FR type PVC insulated unsheathed cable multi-stranded copper conductor as continuous earth wire and connected to earth dolly as required at site& including chases cutting & making good disturbed surface & applying finishes to match existing surface complete all as specified and directed.

M&L sub main wiring with one single core PVC insulated & unsheathed cable 6.0 Sqmm (nominal area) FRLS type having multi-stranded copper conductor drawn in and including not less than 20 mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring with and including 6.0 Sqmm FRLS type PVC insulated unsheathed cable multi-stranded copper conductor as earth wire connected to common earth as per IS & cutting chasing for conduit & sinking for boxes & making good to walls disturbed surface & applying finishes to match existing surface complete including taking down of exsting sub main wiring complete all as specified and directed. NOTE : one runs of 6 Sqmm and one run of 6.0 Sqmm cable and PVC conduit shall be measured as a one unit length.

S & F for switch piano, flush type, 5 amps, single pole, one way, 230 volt complete all as specified and directed.

S & F bell push switch 5 Amp flush type complete all as specified and directed.

S & F for 2/3 pin, 5 Amp/ 6 Amp , socket outlet, flush type, 2 in 1 complete all as specified and directed.

S & F for bell, ding- dong , AC, 230 Volt, single pole complete all as specified and directed.

S&F switch socket combination 2 in 1, 6 pin 16Amps multipurpose type 240 volts complete all as specified and directed.

S&F ceiling rose single phase , PVC poly carbonate, insulated body three terminals ISI marked complete all as specified and directed.

S& F for sheet metal enclousre factory made for MCB DB's SPN, 12 way, double door, 240 Volts with 200 Amp rated bus bars including taking down existing unserviceable MCB DB complete all as specified and directed.

S&F MCB SP 240 Volt 6 TO 40 Amp ISI marked conforming to 'C" curve, breaking capacity 10 KA complete all as specified and directed.

S&F MCB SPN 40 to 60 amp 30mA for earth leakage. Over load and short circuit protection ISI marked complete all as specified and directed.

S&F stepped type electronic fan regulator flush type AC 230 volt suitable for any type of ceiling fan complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V,AC integrated type including driver, Extruded aluminum housing (enhances safety) with high quality polycarbonate diffuser , 4 ft,2000lm,voltage protection range 140V -270 V,NW 4000K , ,connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED lights fitting 1x 10W, 220V,AC integrated type including driver, Extruded aluminum housing (enhances safety) with high quality polycarbonate diffuser , 2 ft ,connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S & F Building security/street LED light fitting 35 watt IP-65 protection pressure diecast alluminium body,heat resistant glass,including driver and making necessary electric connection with 2.5 sqmm twin core copper wire 1.5 long complete fixed in and including GI pipe medium grade 40 mm fixed to pole complete all as specified and directed.

Supply and fix electronic meters temper proof LCD display with polycarbonate cover 230 V, 10-60Amp, accuracy class-I 50Hz, conforming to IS 13779, IP-54, with parameters to show data, time,current reading, load, PF, voltage and KWH complete all as specified and directed including taking down old unserviceable meter and deposite in MES store for BER.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified and directed.

Taking down cement or lime plaster incl racking out joints hacking for key scrubbing down with water etc.

M&L rendering 15mm thick in two coats (10mm thick base coat and 5mm finishing coat) in cement mortar 1:4 with using water proofing compound on brick work or concrete surfaces and finishing the surface even and smooth. witrhout using extra cement complete all as specified and directed. Note : WPC shall be measured and paid seperately.

M&L rendering 15mm thick in cement mortat 1:6 on brick work or concrete surfaces of walls and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L rendering 10mm thick in cement mortar 1:3 on concrete surfaces of ceiling and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound ISI marked.

M & L for preparation of newly plastered surfaces of wall & concrete and applying 2 mm thick wall care putty including preparation complete.

M&L for applying 2mm thick Birla / JK Putty in two layers on old wall surfaces including complete removal of existing wall finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper complete.

M&L for applying two coats of oil bound distemper on wall or concrete over a coat of primer on prepared surfaces including, rubbing with sand paper complete.

M & L for preparation of newly plastered surfaces of ceiling and applying 2 mm thick wall care putty including preparation of new surface complete.

M&L for applying 2mm thick Birla / JK Putty in two layers on old ceiling surfaces including complete removal of existing finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper complete all specified and directed.

M&L for applying two coats of oil bound distemper on ceiling over a coat of primer on prepared surfaces including, rubbing with sand paper complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coat cement base paint over one coat of chalk whitening on plastered surfaces complete all sas pecified and directed.

M&L for preparation of old scrapped surfaces of walls of any description by washing, rubbing down and applying two coats of cement base paint complete as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving n. exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection/ flooring etc finishing even & smooth without using extra cement complete all as specified and directed.

Preparing surface of sunken slab and applying 15 mm thick cement plaster in 1:4 cement sand mortar with integral water proofing compound both on floor and wall. The surface shall then be cured and allowed to dry then applying Epoxy Resin coating polymer modified cementitious coating like brush bond of Fosroc, Pidilite and Bostic as per manufacturer's instructions both on floor as well as on wall and sunken floor shall be filled with graded cinder complete all as specified. Note: WPC will be measured and paid separately.

M&L PCC 1:3:6 type C2, (using 40 mm graded stone aggregate) as in sunken slab filling complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition stone slab and tiles of any description or thickness in floors, dado/skirting and apron etc laid bedded and pointed in any mortar complete all as spd and directed.

M&L coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match the shade of tiles over and including 15 mm thick screed bed or bedding in cement mortar 1:6 complete all as specified and directed.

M&L for 10mm thick Lighft shade vitrified ceramic tiles in floors, area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm set & jointed in neat cement slurry and pointed in white cement mixed with pigments to match the shade of tiles over and including 15 mm thick screed bed or bedding in cement mortar 1:6 complete all as specified and directed.

M&L for 10mm thick Light shade vitrified tiles in skitting, exceeding 0.36 sqm but not exceeding 0.42 sqm set & jointed in neat cement slurry and pointed in white cement mixed with pigments to match the shade of tiles over and including 10 mm thick srendering or bedding in cement mortar 1:4 complete all as specified and directed.

M&L for glazed ceramic tiles on vertical surfaces 450 x 300 x7mm thick set and jointed in neat cemet slurry and pointed in white icement mixed with pigments to match the shade of tiles over and including 1o mm thick rendering or bedding in cement mortar 1:4 complete all as specified and directed.

M & L For Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 20 mm thick screed bed or bedding layer in cement mortar 1 : 6 for laying floor finished even and rough complete all as specified and directed.

M & L For Machine cut kota stone slab flooring 20-25mm thick in riser of steps Skitting dado and pillar laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 15 mm thick rendering in cm 1 : 4 as rough surface on vertical surface as backing coat of wall tile complete all as specified and directed.

M&L for Chequered cement concrete tiles 20cmx20cmx25mm/30cmx30cmx25 mm thick set, jointed and pointed in neat cement slurry in floors with grey cement and no pigment including 20 mm thick screed bed in cement mortar 1:6.complete all as specified and as directed.

M&L PCC 1:2:4 type B1 (using 20mm graded stone aggregate) , 25 mm thick as in sub top layer of floor and finished rough to receive the floor tiles.

Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors complete.

M&L ATT Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed.

Demolition of brick work built in cement mortar complete all as specified and directed.

M&L for brick work using old size sub clas 'B' brick in cm (1:6) straight or curved on plan exceeding 6.00 mtr mean radius complete all as specified and directed.

The same as item No 71 above but except bricks.

M&L brick work using old size sub class 'B' brick in cm (1:4) straight or curved on plan exceeding 6.00 mtr mean radius complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutter from the frame) not exc 1.5 sqm each complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutter from the frame) exc 1.5 sqm but n exc 4.0 sqm each complete all as specified and directed.

S&F Pressed steel frames (Factory made) made out of 1.25 mm thick black MS sheet for doors, with one or more rebates including necessary fixing lugs, Butt hinges, lock strike plate, etc complete, size of frame 105x60mm incl bottom of each chowkat to be welded with 2 nos 25x25x3mm thick flat iron projecting 10 cm on either side and back fill to chowkats with PCC 1:3:6 type C-0 using 12.5 mm graded crushed stone aggregate complete all as specified and directed.

The same as item No 76 above but size of frame 125x60mm complete all as specified and directed.

S&F Mild steel works as in hold fasts, clamps, plain angle cleats for securing purlins to wood trusses or rafters, cooler stands and similar small articles conforming to Fe 410-0 or Fe 310-0

S&F 35mm thick 2nd class hardwood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces , size of rail and stile as per IS:1003 (Part-I), Klin seasoned and chemically pressure treated complete all as specified and directed.

S&F flush shutter, 35 mm thick, solid core construction with block board core, and ply wood face panels but both face is covered with decorative laminate face veneer with lipping complete all as specified and directed.

S&F in repair 2nd class hard wood 35 mm thick glazed and gauzed skelton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut complete all as specified and directed.

S&F, 200 mm long aluminum anodised barrel tower bolts of extruded section as specified.

S&F, in repair 200 mm long aluminum anodised barrel tower bolts of extruded section as specified.

S&F, in repair, aluminum alloy anodised sliding door bolts with hasp & staple & fixing clips of sheet cast extruded section & fixing bolts & sliding bolts of extruded section 300 mm long.

S&F150 mm extruded aluminium alloy handles, fabricated type anodised complete all as specified.

S&F Solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening complete all as specified and directed.

S&F factory made solid Panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and gap insert for top and bottom rail; panelling of plain colour PVC sheet 5mm thick to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, complete all as specified and directed.

S&F 75 mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-22 complete all as specified and directed.

S&F 100 mm extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed.

S&F 100 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F steel windows with side hung shutter incl box type butt hinges with bow handle,steel peg stay, tower bolts ( each shutter having two tower bolts 100mm long ) complete with glazing bars dovetailed or welded complete all as specified and directed.

S&F steel windows with side hung shutter incl box type butt hinges with bow handle,steel peg stay, tower bolts ( each shutter having two tower bolts 100mm long ) complete without glazing bars dovetailed or welded complete all as specified and directed.

S&F Steel ventilator with top hung shutter including, hinges, peg stay, complete all as spd and as directed

S&F GI wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staple complete all as specified.

S & F sheet glass 4mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

The same as item No 95 above but glass is frosted or grounded on one side.

S&F Mild steel framed works such as grills,gratings,etc, with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work for portions framed and hung as gates, including pintle hinges, stops, hand made sliding bolts, etc conforming to Fe 290 Gde -E-165.

Preparing surfaces of new wood and wood based materials of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint over a coat of pink primer.

M & L preparation of new steel surfaces any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red-oxide primer complete all as specified and directed.

Cutting holes in brick walls exc 1/2 brick & n exc full brick built in cement mortar for inserting hold fasts, cutting and preparation of brick wall for insertion of doors, windows & ventilator and making good dismantled portion in cement mortar 1:3 etc complete all as specified and directed.

S&F in repair MS PVC sheathed 20mm dia drapery rod including Bracket ,end ball , rounded block (coated with brown/cherry/Golden colour) of approved pattern and shade complete all as specified and directed.

S&F 18/19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, including teak wood lipping, 6 mm thick on sides complete for cupboard shutter and incl shelves complete all as specified and directed.

S&F, in repair, Hardwood 2nd class boarding, 30mm thick planed both side , fixed in shelves, partitions and shelves of built-in cupboards, almirah, book cases, toilet boxes, racks, pelmets and similar work complete all as specified and directed.

S&F Hasp and staple, mild steel, safety type, stove enameled black, including bolt to hinge plate and fixed with screws of 125mm size

Taking up or down steel tubing 15 mm dia and connections including cleaning for re-fixing or removal to store etc

Taking up or down steel tubing 20 mm dia and connections including cleaning for re-fixing or removal to store etc

Supply & laying of 16mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings and wall / ceiling or laying in floors complete all as specified and directed.

Supply & laying of 20mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings and wall / ceiling or laying in floors complete all as specified and directed

Cutting chases in brick walls, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

Dismantling of AC/PVC/CI pipes in cement mortar from walls including all type of bends/branch pieces complete all as specified and directed.

M&L PVC (SWR) pipes single socketed in any length with rubber ring joints ,fixed to wall, dia of bore 110 mm complete all as specified and directed.

The same as item No 111 above here in before but 75 mm

S&F PVC (SWR) bends any radius of 75 mm dia

S&F PVC (SWR) bends any radius of 110 mm dia

S&F PVC (SWR) bends any radius provided with access door of 110 mm dia

S&F 75/100mm bore PVC (SWR) floor trap, plain with grating including jointing to waste pipe complete all as specified and directed.

S&F in repairs sinks without drainge board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; & pvc waste pipe including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F in repair 0.63 mm thick kitchen plate rack made of stainless steel 900 x 750 x 220 mm size fixing with wooden plug with suitable size of screws complete all as specified and directed.

S&F in repair water closet white vitreous china ware Orissa pattern of size 580x440mm with integral foot rest ‘P’ or ‘S’ trap front or back inlet incl provision of PCC bedding type B1, 1:2:4 ( 20 mm graded aggregate) and connection pipes ( excluding flushing cistern but including flushing pipe 32 mm dia MS chromium plated) (rate also include for taking off unhygienic of WC).

S&F in repair 10 Ltr capacity PVC valveless shyphonic action type low level flushing cistern white with inlet, ball valve, float valve and handle incl bracket and flush pipe of low level of 32mm dia fixed to wall complete all as specified and directed.

S&F in repair vitreous china WHB size 550x400 mm white flat back including pvc waste pipe but excluding taps, waste, chain & plug & porcelain stopper but including brackets painted with two coats of synthetic enamel painting over a coat of red oxide primer etc complete all as specified and directed.

S&F in repair 15 mm bore pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly-nuts screwed for iron pipe & fixed complete all as specified and directed.

S&F in repair chromium plated single lever wall mixer 3-in-1 system with provision of both hand shower complete with 115mm long bend pipe, connecting legs and wall flange complete all as specified and directed.

S&F in repair chromium plated overhead shower rose swivel type 125 mm with CP arms 300 mm long complete all as specified and directed

S&F in repair CP brass tubular towel rail 20 mm dia D type 60 cm long between flanges complete all as specified and directed.

S&F in repair of stainless steel soap dish, of standard size and shape complete all as specified and directed.

S&F in repair bib tap 15 mm bore, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe.

S&F in repair PVC connection 15mm dia size and 450 mm long with 2 Nos check nuts its washers complete all as specified and directed.

S&F 100 mm dia grating doom of stainless steel complete all as specified and directed.

Demolition of reinforcement cement concrete above the ground floors n exc 15 cm thickness (Reinforcement cut as required to facilitate demolition) such as cooking platform, chajjas etc

M&L for RCC as in kitchen platform, shelves & chajjas etc 1:2:4 type B1 (using 20 mm graded stone aggregate) including necessary form work complete all as specified and directed.

M&L for 20 mm thick granite slab (of any type) work (table rubbed and polished) in cooking platforms, steps, window cills, incl edge moulding & cutting holes for gas pipe through drill machine and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 20 mm thick screed bed in cm 1:6 complete all as specified and directed.

S&F MS TMT bar 8 dia & over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.90mm dia or securing with clips.

Dismantling water tanks and removing to store of capacity exc 250 and n exc 500 ltrs complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks in white colour tripple layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I of 500 Ltr capacity complete all as specified and directed.

S&F Ball valves 20mm dia high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210gms) complete all as specified and directed.

S&F in repairs Gun metal, globe or gate valve with iron wheel head, 20 mm bore, screwed both ends for iron pipe complete all as specified and directed.

M&L PCC 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as on roof base etc complete all as specified and directed

M&L for 15 mm thick plaster in CM 1:4 with water proofing compound @ 200ml /50kg of cement or as per manufacturer's instruction finished surface even and smooth with out using extra cement including taking down of complete existing cement plaster etc complete all as specified. Note : WPC will be measured & paid separately.

M&L for water proofing treatment on non approachable / non accessible roof surface horizontal and vertical surfaces in following sequence through manufacturer / authorized applicator of the manufacturer complete all as specified and directed :- (i) Properly cleaning and drying concrete surfaces. (ii) Applying a coat of oxidized bitumen based solvent primer @ 0.3 Kg / sqm. (iii) Applying evenly tack coat of industrial bitumen 85 / 25 grade @ 1.2 Kg / sqm. (iv) Laying unrolled over the bitumen coat surfaces polymeric water proofing membrane, hyperplas standard weight not less than 3 Kg / sqm with 100 mm over laps shall be sealed by flame as per manufacturer instruction. (v) Applying a coat of aluminium paint @ 100 gm / sqm over and including a coat of hot air blown grade bitumen of grade 85 / 25 @ 1.2 Kg / sqm duly sanded over polymeric membrane complete. NOTE:- The polymeric water proofing membrane shall be extended upto parapet walls and inserted in walls by cutting groove and making good with cement mortar 1:3 as directed.

Demolition of cement concrete bed in haunching and breaking up drain pipes SGSW set in cement mortar of 200 mm dia.

M&L for concrete bed in P.C.C. 1:4:8 type D2 (using 40mm graded stone aggregate) to drain pipes including packing under and haunching against the sides of the pipes after laying & testing complete all as specified and directed for the 200 mm dia of pipes.

M/L for DWC (Double wall corrugated) HDPE Pipes laid in trenches including jointing accessories complete bed to level/gradient as directed by engr- in -charge all as specified of 200 mm dia size.

Blocking up the entry of septic tank of the following capacities and pumping out effluent dirty liquid and sludge from sludge chambers of septic tank (including settling tank and intercepting chambers etc up to bottom) collecting sludge in closed cart and removing away and cleaning the septic tank with clean water and opening entry sewage line for re-use and removing sludge from the premises (outside to MOD Land) complete all as specified and directed. (The rate included for excavation of barrow pits for burying of removed sludge under the ground and making good the excavated earth to a true surfaces). :-

Septic tank for 100 users.

Septic tank for 50 users.

Cleaning of blocked sewage line of the following dia by using bamboo sticks or MS rods and revolving with rope inside the sewer line between two manholes and cleaning the sewer line with fresh water including taking out sludge complete all as specified and directed.

150 mm dia

200 mm dia

M&L for dewatering of efflorescent from soak well of any capacity by means of 7.5 HP non clogging diesel driven pump (including necessary fuel and T&P etc) in nearest drain complete all as specified and directed .

Blocking up the entry of manholes of any size depth and pumping out effluent dirty liquid and sludge from bottom of manholes including collecting sludge and dirty liquid into closed container and cleaning the manholes with fresh water after wards opening the inlet of manhole for re-use and removing the sludge to outside premises, complete all as specified and directed.

Cleaning of blockage of WC /GullyTrap/Nahani Trap/Floor Ttrap any other similar kind of items complete all as specified and directed.

S&F in repair Vitreous China wash down water closet pan pedestal pattern white incl fixing bolts,include S&F white coloured plastic seat cover,CP brass jet nozzle with 600 long PVC pipe

S&F repair vitreous china urinals bowl type flat back, size 465 x 355 x 265 mm, white , complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and union for discharge pipe.

S&F PTMT urinal spreader for fixing with 15 mm bore pipe complete all as specified. Make : Hindustan/Parryware/Prayag

Please Enable Macros to View BoQ information