CERTAIN WATER SUPPLY REPAIR WORK DURING REPUBLIC DAY CAMP AT NCC PARADE CAMP NCC GROUND AND NCC CADETS LIVING AREA UNDER GE U WATER SUPPLY DELHI CANTT-10

Amount

Labour only for attending day to day external water supply complaints of all nature i.e leakage in water supply pipe lines , fitting/fixture, over flow of overhead tank, no water supply, taking out water from trenches during repair including writing the complaints in complaint register complete all as directed by Engineer-in-charge. (Any material required for attending complaints shall be measured and paid separately under respective item herein after)

Notes for item No. 1 1.00 The complaints shall be attended and the defects shall be rectified by a team of expert and experienced electrician/plumber as applicable assisted with adequate number of helpers as directed by Enginner-in-charge. 2. The complaints shall be attended and defect shall be rectified within 08 hrs commencing from date and time of notifying the complaint failing which a penalty @ Rs 500/- per complaint per day (08 hrs) shall be levied upon/imposed on the contractor and recovery shall be made from contractor's dues.Contractor rep shall be available wef 0800 hrs to 2000 Hrs to receive and notify the complaint. 3. In case, after checking and attending the defect, it is not possible to rectify the defects within 08 hrs the facts shall be brought to the notice of Engineer-in -charge by the contractor or his rep . If Engineer -in-charge is satisfied with contractors view, no recovery will be made.

4. While attending the complaint of water supply if earth work is required then the same shall be measured and paid seperately under appropriate item of Sch 'A' . However no extra payments shall be made for dewatering. 5. Cutting of GI pipe in position and threading is also deemed to be included in the job rate (Fitting and fixtures will be measured and paid separetely under respective item of Sch A). 6. All T & P as well as dewatering motor single phase of 3HP with including 100 mtr cable, required for attending the complaints shall be provided by the contracor. 7. The pipe fitter shall always be in possession of die set complete with cutters , Taps , Pipe wrench, Chain wrench,Caulking tools,Complete set of spanners and ladders etc…, as required at site. 8. The elecrician shall always be in possession of all Electrician tools, LT Megger, Earth tester, Multimeter, Crimping tool, insulation tape, Hand gloves etc required at site. 9. BOO : All the materials as procured by contractor for fixing / fitting/ laying of materials as mentioned below shall be taken of charge with indicating purchase vouchers reference of materials and its quality and quantity shall got verified through BOO & to be issued through baby indent / USR's for material consumption at site as per requirement/complaint.

Supply & fixing in replacement of UNSV Tank nipple 20 mm dia of required length complete all as specified and directed.

Supply & fixing in replacement of UNSV GI Socket Med grade ISI Marked of following sizes ;-

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

80 mm bore

Supply & fixing in replacement of UNSV GI Elbow Med grade ISI Marked of following sizes : -

15 mm bore

20 mm bore

25 mm bore

40mm bore

50mm bore

80 mm bore

Supply & fixing in replacement of UNSV GI Union Med Grade ,ISI marked of following Sizes:-

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

80 mm bore

Supply & fixing in replacement of UNSV GI Nipple of different length as per requirement, both end screwed Medium Grade, ISI marked of following sizes:-

15 mm bore

20 mm bore

25 mm bore

40mm bore

50mm bore

Supply & fixing in replacement of UNSV PVC 'L' type Holder suitable for Aluminium rod,Float Ball etc complete all as specified and as directed by Engineer - in - charge of following Sizes:-

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

Supply & fixing in replacement of UNSV GI Reducing socket medium grade ISI marked of the following sizes :-

25 mmx15mm bore

20mmx15mm bore

25 mm x 20 mm bore

50 mmx 40mm bore

40 mmx 20mm bore

40 mmx 25mm bore

50mmx 25mm bore

Supply & fixing in replacement of UNSV GI Tee Med grade ISI Marked of following sizes : -

15mm x15mm x15mm

20 mm x 20 mm x 15 mm

20 mm x 20 mm x 20 mm

25 mm x 25 mm x 25 mm

25 mm x 25 mm x 15 mm

25 mm x 25 mm x 20 mm

40 mm x 40 mm x 40 mm

40 mm x 40 mm x 20 mm

40 mm x 40 mm x 25 mm

50 mm x 50 mm x 50 mm

50 mm x 50 mm x 40 mm

50 mm x 50 mm x 25 mm

50 mm x 50 mm x 20 mm

Supply & fixing in replacement of UNSV GI solid plug heavy duty ISI marked of following sizes

15mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

Supply & fixing of Lead pig bar suitable for joints complete all as specified and directed.

Supply & fixing of spun yarn complete all as specified and directed.

Supply & fixing of 3mm thick rubber gasket complete all as specified and directed.

Supply & fixing of lead wool complete all as specified and directed.

Supply & fixing in replacement of UNSV PTMT float valve with epoxy coated aluminium rod and high density plastic ball of following sizes complete all as specified and directed by Engineeer-in-charge:-

15mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

Supply & fixing in replacement of UNSV Gun metal gate valve with iron wheel head screwed both ends for iron pipe , ISI marked, as per IS : 778 of following sizes complete all as specified and directed by Engineer - in-charge

15mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

(Note :- Same as per petty of M/s Rahul Enterprises of AGE W/S-III)

Excvation in trenches not exc. 1.5 mtr wide and not exc 1.5 mtr deep for pipe line in soft/loose soil, getting out and levelling of bottom surface to required complete all as specified and as directed by Engineer-in-charge.

Returning filling, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick complete all as specified and as directed by the Engineer-in-charge.

Removing excavated material from site to a distance not exc 50 m away and depositing where directed not exc 1.5 meters above the starting point complete all as directed by Engineer-in-charge.

Surface dressing of uneven surfaces of the natural ground, rough excavated surfaces and filled area where ordered shall be trimed to an even surface horizontal or slopping, by removing vegetation and by scrapping high patches and filling low patches with the scrapping soil to given an even and neat look to the site. depth of cutting not exceeding 15 cm. complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement of UNSV 15 mm bore Bib tap standard of PTMT any colour high pressure screwed for male/ female treaded, for UPVC pipe of size 15mm bore complete all as specified and directed

Supply & fixing in replacement of UNSV 'stem' made out from SS (all as per sample) of sluice valve of size as under : -

80 mm bore

100 mm bore

150 mm bore

Supply & fixing in replacement UNSV 'stem nut' made out from stainless steel suitable to match with existing sluice valve of sizes as under : -

80 mm bore

100 mm bore

150 mm bore

Supply & fixing in replacement UNSV 'gland plate' made out CI, suitable to match with existing sluice valve of sizes as under : -

80 mm bore

100 mm bore

150 mm bore

Taking up or down steel tubing with connection from trenches / walls including cleaning for removal complete all as specified and as directed by Engineer-in-Charge of the follwing sizes :-

15 mm dia

20 mm dia

25 mm dia

40 mm dia

50 mm dia

80 mm dia

Relaying/refixing only jointing and testing of old GI pipes with new GI fittings such as Tee, elbow, socket & bend etc including cleaning completely in trenches as directed (serviceable pipe shall be picked up from item No 25 here in before ) for the following sizes :-

20 mm dia

25 mm dia

40 mm dia

50 mm dia

80 mm dia

Supply & fixing in replacement UNSV GI pipe medium grade ISI marked including all fittings in old/new position as in walls and ceilling complete all as specified and directed of following sizes :-

15 mm dia

20 mm dia

25 mm dia

40 mm dia

50 mm dia

Supply & fixing in replacement UNSV GI pipe medium grade ISI marked including all fittings in old/new position as in trenches complete all as specified and directed of following sizes :-

15 mm dia

20 mm dia

25 mm dia

40 mm dia

50 mm dia

80 mm dia

Labour for cutting and screwing existing steel tubing for alteration or addition complete all as speicified of the following sizes :-

15mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

Supply & fixing in replacement UNSV cast iron/ DI fitting for flanged spigot and socketed pipes such as bends , reducer, tee pieces, tail pieces, collar, cross, caps & plug upto 150mm bore complete all as specified and directed.

Taking up cast iron/ductile iron water mains including all fitings with spigot and socket ends and lead joint including burning out joints and removing lead of size

100 mm bore

150 mm bore

Relaying/refixing of pipe CI/DI pipes after cleaning from inside with suitable chemical and rodding complete all as specified and directed by Engineer -in-charge of fwg dia :-

100 mm bore

150 mm bore

Supplying ,laying ,jointing ,testing and commissioning in replacement UNSV DI pipe as per IS 8239 class K-7 with in side cement mortar lining with spigot and socketed end laid in trenches complete with rubber gasket joint complete all as specified and as directed at site for the following sizes:-

100 mm bore

150 mm bore

M&L painting on steel and iron surfaces with one coat of synthetic enamel paint as per existing colour scheme or pattern after preparation of old painted surface of any description over 10cm in width or girth complete all as specified and as directed by Engr-in-charge

Supply & fixing in replacement of UNSV Sluice Valve of sizes as under , ISI Marked, flanged ends drilled pressure rating PN-1.6, PD Short body, Confirming to IS 14846 -2000, having stainless steel spindle with cast iron operation wheel at top including taking out unserviceable sluice valve and depositing to MES store yard complete all as specified and as directed at site by the Engineer-in-Charge. (Note:- Flanged joints complete with jointing material shall deemed to be included in the unit rate of this item.)

100 mm bore

150 mm bore

Supply & fixing in replacement of UNSV of flanged ends water meter of following sizes ISI marked woltman type, Class 'B' and making good connection with flanged ends, with gasket rubber sheet and nut & bolts fixing in horizontal/inclind/vertical position, including taking out unsv water meter complete all as specified and directed at site by the Engr-in-Charge. (Note :- Flange joints including jointing materials shall deemed to be included in the unit rate of this item.)

Supply & fixing in replacement of UNSV flanged ends strainer/dirt box of following sizes with stainless steel mesh suitable for cold water meter to avoid foreign material entering into meter and making good connection with flanged ends, with gasket rubber sheet and nut & bolts fixing in horizontal/inclind/vertical position, including taking out unsv strainer/dirt box complete all as specified and directed at site by the Engr-in-Charge. (Note :- Flange joints including jointing materials shall deemed to be included in the unit rate of this item).

Supply & fixing in replacement of UNSV CI foot valve including nut and bolts washers and rubber 100mm dia confirming to IS-4038 complete all as specified and as directed

Note:- Sch of credit amount of Rs.26037.00/- shall be deducted from total quoted BOQ Amount when work acceptance letter issued.

Deven Associates