TIRUPATHUR DISTRICT SCPAR 2025-26 CONSTRUCTION OF PANCHAYAT UNION OFFICE AT KANDHILI

Amount

CONSTRUCTION OF PANCHAYAT UNION OFFICE AT KANDILI

Earth work Excavation for Foundation in all soils and Sub Soil to full depth as may be directed except in hard rock requiring blasting but inclusive of shoring strutting and requiring the sides of foundation.

Supplying and filling with M.sand in layers of not more than 15cm thick for foundation

Cement Concrete 1:4:8 (One Cement, Four sand and Eight hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete.

Supplying and Filling the foundation and basement with excavated earth in layers of not more than 15cm thick well rammed, watered and consolidated as directed by the deptl. officers. Complete complying with standard specifications.

Supplying and Filling the foundation basement with conveyed earth in layers of not more than 15cm thick well rammed, watered and consolidated as directed by the deptl. officers. Complete complying with standard specifications.

Supplying and erecting water tight steel shuttering to centering including necessary supports for plane surface in Foundation and Basement for RCC Columns, Footings, Plinth beams, bed blocks, staircase steps etc., using suitable mild steel sheets etc., complete.

Supplying and erecting, centering for sides and soffits including supports and strutting up to 3.29m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheet etc., complete.

Plane surfaces such as RCC floor slab, roof slab, rectangular square Tee or Ell beam, lintels, bed blocks staircase waist slab, landing slab, landing beams, etc.

Providing and laying in position, Standardised Concrete Mix M-25 Grade in accordance with IS:456-2000, using 20mm and down grade hard broken granite stone jelly for all RCC Items of works with minimum cement content of 350kg/m3 and maximum water cement ratio of 0.50, including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS:9130 to accelerate, rated setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m) 7730kg. of 20mm machine crushed stone jelly and with about (3.3cum) 5156 kg. of 10-12mm machine crused stone jelly and with about (4.79cum) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with Mechanical vibrators, finishing, curing, etc.,and providing fixtures like fan clamps in the RCC Floor / roof slabs wherever necessary without claiming extra, etc., Complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No Separate payment will be made by the Department for the excess usage of materials).

Column footing - Foundation basement

In Ground floor

In First floor

In Second floor

In Terrace floor

Supplying, fabricating and placing in position M.S. or R.T.S. reinforcement grill for RCC works as per the design given including cost of steel and binding wire etc., complete complying with standard specification. (The contractor will have to make his own arrangements for the supply of M.S. plain rods / RTS rods and binding wire)

Brick work using second class Country bricks of size 8 3/4" x 4 1/4" x 2 3/4" in Cement Mortar 1:5 (one cement and Five sand) including curing, neat finishing, etc, complete complying with standard specification.

Foundation and Basement

Ground Floor

First Floor

Second Floor

Terrace Floor

Brick partition wall of 11cm thick using country bricks of size 8 3/4 x 4 1/4 x 2 3/4" in cement mortar 1:3 (One cement and three sand) using hoop iron reinforcement if found necessary including finishing and curing etc., complete.

Ground floor (11cm thick)

In First floor (11cm thick)

In Second floor (11cm thick)

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothy with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The Surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (waterproof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the Departmental Officers. [The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (waterproof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coat of putty, scrapping the putty area to level the surface smooth, etc., complete). The Putty should be got approved by the Executive Engineer before use on work. (Based on SoR 2023-24)

Plastering with cement mortar 1;5, using 12mm thick in all floors etc.,complete.

Paving the floor with best approved quality fine polished Vitrified tiles of size 610x610x20mm machine cut edges laid over cement mortar 1:3 (One cement and three sand) 20mm thick etc., complete.

Tactile Paver type of New tek BT Yellow colour Ceramic tiles of size 305x305x15mm for vision Impairment person Surface preparation including cleaning the joint to be free from dust and loose particles. Providing masking tape on either side of the tile joint edges and providing sealing the tile gap with epoxy tile joint grout and finishing neatly and as directed by the departmental officers. The rate inclusive of cost of materials labour etc complete

Paving the floor with best quality Vertified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three crushed stone M.Sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing with white glazed tiles for approved quality of tiles including cost and labour charges etc.,complete 150x150x6mm

Supplying and fixing fine polished cuddapah slab of following thickness for Urinal devider arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as direct.

Supplying and fixing of Anti-Skid tiles for approved quality including cost and labour fixing charges etc.,complete.

Supply and fixing of MS grill for windows with 35 x 6 mm plate using 12 mm square rod including cost and conveyance and all other labour charges(53.60+29.10) PWD SOR

Manufacturing,supplying and fixing of stainless steel hand rails for staircase using 50mm dia 304L grade stainless steel pipe of 1.6mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia stainless steel pipe post of 1mm thick as vertical at 900mm centre with 2 Nos of 25mm dia intermediate horizontal stainless steel pipe of 1.6mm thick in between.The vertical pipe has to be welded to the 100 x 100 x 6mm MS base plate encased in the base concrete.The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance,electrical charges,ect.complete.

UPVC Window supplying and fixing UPVC ( Un-PLASTICIZED Polyvinyl chloride) windows of casement type (open) from the profile the size of outer frame 60mmx58mm and shutter profile are reinforceement with gi/1mm 125GSM and 100% corrosion free, the profiles are mlulti chamberedcv section with wall thick of 2mm.The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power points locks and also it operates as handle.The corners and joints should be welded and cleaned.Radiations free pin headed plain or brownclour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action,security protective hinges,strong locking systems and as per size for arresting noise and energy loss.

UPVC VENTILATOR:Supplying and fixing UPVC (Un-PLASTICIZED Polyvinyl chloride)Louvered Ventilators of from the profile the size of outer frame 60x58mm and shutter profile the size of 60x78mm both profile size of 60x78mm both profiles are reinforced with GI/1MM 125GSM and 100% corrosion free,the profile are mulit chambered sections with wall thick of 2mm.The EPDM rubber ( black colour) covered with all over he edges of frame and shutter.The corners and joints should be welded and cleaned.Radiation pin headed glass 4mm thick should be fixed to the wall with 100% packing with screws and silicon packing all aroundthe frame.The ventilator should be got approved from the Executive Engineer before use on work.

Solid PVC Door shutter with frame using 19 gauge 19mm MS sq. tubes for styles and outer frames, 15mm MS sq. tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for paneling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter.

Supplying and fixing of MS Box type door frame etc.,complete.

Supplying and fixing of MDF shutter for approved quality including cost and all accessories etc.,complete. Double Leaf

Supplying and fixing of 2/3 Grill and 1/3 paneled door including cost of all materials and labour fixing charges etc.,complete.

Toilet Sunken using broken brick jelly 20 mm gauge The proportion of broken brick jelly to slaked lime being 1:3:6 (1part cement,3 part fine aggregate & 6 part broken brick jelly)

Painting two coats to new Iron works including cost and labour charges etc.,complete.

Painting with Oilbound Distember paint 2 coats over one coat of priming cost for approved quality including cost and labour charges etc.,complete.

Painting with Plastic Emulsion paint 2 coats over one coat of priming cost for approved quality including cost and labour charges etc.,complete.

Weathering Course concrete with broken brick jelly of 20mm gauge in pure slaked lime to be laid in a single layer (No sand to be added) over roof slab the proportion of brick jelly to lime being 32 to 12.5cft by volume well beaten with wooden beaters etc., complete.

First Floor

Terrace Floor

Finishing the top of roof with one course of New Machine Pressed tiles of approved quality of size 23x23x2cm laid in cement mortar base layer 1:3 (One cement and Three sand) 12mm thick mixed with water proofing compound etc., complete.

PAVER BLOCK

Earth work excavation for pavement & drain in all soils and sub soils and to full depth as may be directed except rock requiring blasting but inclusive of shoring strutting and baling out water wherever necessary etc., complete.

Cement concrete 1:4:8 (One cement four sand and eight aggregate) using 40mm gauge hard broken granite stone including all incidental charges, dewatering if found necessary etc., complete.

Plain Cement Concrete 1:3:6 (one cement, two M.Sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of

Providing and laying spreading and compacting graded stone aggregate to Wet Mix Macadam(WMM) specification including premixing the material with water at OMC in machanical mix plant carriage of mixed material by tipper to site laying in uniform layers 250mm thick with pavers in SubBase/Base course on well prepared surface and compacting with vibratory roller to achieve the desired density including cost of material,labour charges, rentals for machinery, fuel and all other incidental charges etc., complete.

Providing and Laying of Interlocking Concrete Block (Surface Textured) Pavements having thickness 80mm and compacted over a thin bedding M.Sand layer of 30 mm thickness and joints shall be filled by fine M.Sand of specified grading as per table 1500.6 of Specification of Rural roads-2014 and Technical specification clause 1504.

SANITARY FITTINGS

Supply and fixing in position best approved quality and make white glazed earthen ware oriya type Indian water closet of size 580 mm with P or S trap embedding the closest and trap to shape in position with brick jelly lime concrete 1:2:5 (one lime two sand and five brick jelly) using 40 mm broken brick jelly and finishing the top to required slope and including giving connections to the PVC soil stacks using 0.60 m long PVC Pipe 110 mm dia. 6 kg/sqcm by dismantling masonry, RCC roof or floor slaps and making good, the disturbed portion to original condition without and leakage etc. complete as directed by the departmental officers and complying with standard specifications (The water closet P or S trap are to be got approved by the Executive Engineer before use on works)Supplying and fixing white colour glazed Indian water closet, Orissa pattern,with dual flush (3 & 6 lit) PVC cistern mounted on wall, Parryware or equivalent, with PVC, P or S trap having 100mm dia outlet and 50mm deepwater seal, embedding trap and water closet in cement concrete in 1:4:8 mix.

Supplying and fixing in position by means of 75mm long and 6.5mm dia counter sunk bolts and nuts embedded in the floor with rubber or fibre washers. Best quality and approved make white glazed earthern ware European water closet with P or S trap with seat and double flapped rigid PVC seat cover with chromium plated hinges, and giving necessary connection to PVC socket using 110 mm dia PVC pipe 6 kg/sqcm.of 0.60m length including supplying and fixing PVC tank of 10.00 litre capacity with all internal fittings with a pair of cast iron brackets and with all fittings such as 15mm dia nylon connection, 15mm dia GM wheel value, 15mm dia brass nipple including, labour charges for fixing the flushing tank on wall with teak wood plugs and screws, giving water supply connection, painting CI brackets with two coats of best approved quality synthetic enamel paint over a coat of red oxide primer, redoing the disturbed masonry and flooring to original condition, etc. complete complying with standard specification.

Supplying and fixing in position best Indian make wash hand basin of size 550mm X 400mm and approved brand and quality with a pair of C.I. Brackets fixed to wall with necessary teakwood plugs and brass screws one No. of 15mm C.P. Pillar tap, 32mm C.P. Waste coupling, rubber plug and chain, 32mm G. I. Union, 32mmG. I. Waste pipe, 15mm dia G. M. Wheel valve 15mm brass nipple and nylon connection including cost of white lead TW Plugs clamps, rubber washer, etc., complete. (The wash hand basin should be got approved from the Executive Engineer before use on works).

Supplying and fixing in position best quality chromium plated towel rail of 60cm length and 20mm dia with C.P brackets of same material including fixing with necessary T.W Plugs, Brass C.P. screws and dismantling masonry etc., Complete complying with standard specification.

Supplying and fixing Brass CP soap tray including fixing with necessary teak wood plugs, CP screws and dismantling masonry and redoing the sane to the original condition.

Supplying and fixing of CP Two Way Bib Cock with Health Faucet ,wall hook & one metre long flexible tube including cutting and making good the walls wherever required etc complete. complying with standard specification and as directed by the Department officers. The quality and make of health faucet should be got approved by Concern department Engineer before use on work.

Supplying & fixing in position 15 mm dia brass/ C.P screw down tape (Heavy duty) of approved make conforming to I.S. Specifications & quality including cost of shellac, thread etc., complying with standard specifications & including cutting & threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the work).(GARDEN&IWC)

Supplying,installing,testing and commissioning of approved make CONCEALED STOP COCK for toilet including neccesary accessories etc,complete,works include making require size curout in wall,and fixing the control box property,redoing the same etc,complete the quality and make of concealed stop cock should be got approved by concern department Engineer before use on work.

Supplying and fixing CP angle cock with wall flange including cutting and making good the walls wherever required etc., complete complying with standard specification and as directed by the Engineer Incharge before use on work.

Supplying and fixing in position PVC Pipe of 6 kg per sq.cm. best approved quality and make conforming to ISS of the following diameter and providing leak proof joints etc., including fixing to the wall with necessary teakwood plugs, brass, screws, mild steel clamps, etc., and giving connections to the sanitary fitting including dismantling brick masonry RCC floor or roof slab etc., wherever necessary and redoing the disturbed portion to the original condition complete complying with standard specification (The PVC pipe should be got approved from the Executive Engineer before use on works).

110mm dia PVC Pipe AGL

75mm dia PVC Pipe

160mm dia PVC Pipe BGL

Supplying and fixing in position best approved quality PVCNahini trap of 110 mm x 75 mm size with stainless steel gratings of approved quality fixed over a bed of lime concrete.1:2:5 (one lime two sand and five brick jelly) using 40mm broken brick jelly including dismantling the flooring concrete / Brick masonry wherever necessary and redoing the disturbed portion to the original condition and giving in connection to the PVC soil (stacks) pipe as directed etc., complete complying with standard specifications. (The PVC Nahini trap should be got approved from the Executive Engineer before use on works).

Supplying and fixing in position P.V.C. ventilating shaft of 110mm dia with working pressure of 4kg/cm2 and 3m height with P.V.C. cylindrical cowl and fixing in position as directed etc., complete. (The P.V.C.pipe and cowl should be got approved from the Executive Engineer before use on work).

Supplying and Fixing of Incinators for Ladies

Supplying and fixing in position of Indian make White Glazed earthern ware lipped mouth flat back urinal of best approved quality with G.I.Pipe connection of suitable length,32mm bell mouthed P.V.C. connection,15mm dia G.M. Wheel valve, fixing the urinal to the wall in position with necessary T.W. Plugs,Clamps, Screws, Shellac etc., including dismantling masonry if necessary and redoing the same to original condition, fixing the 15mm dia G.I. Pipe connection and wheel valve, paintinf the pipe with two coats of approved paint over one coat of primer and checked without any leakage complete, complying with standard specifications. (The Urinal should be got approved by the Executive Enginer before use on work)

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

WATER SUPPLY ESTIMATION

PART - A SOIL, WASTE AND VENT PIPE LINES

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages,etc., complete complying with standard specifications.(The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level.

40mm dia. 6kg class PVC pipes.

50mm dia. 6kg class PVC pipes.

75mm dia. 6kg class pipes.

110mm dia. 6kg class pipes.

160mm dia. 6kg class pipes.

Supplying and fixing in position of the following dia PVC specials such as PVC vent Cowl etc.,of approved quality and variety of various size confirming to ISS amend providing leak proof joint etc., including necessary cutting and fixing and giving connection to PVC pipes etc., complete complying with standard specification and as directed by the Departmental Officer

75mm dia

110mm dia

PART-B - EXTERNAL DRAINAGE

Supply and fixing in position best quality PVC IS 4985 - CLASS- III - 6 Kg/Sqcm -Soil/ waste pipes of various size with approved quality and variety of various size confirming having ISI mark and providing leak proof joints including erection of below ground with excavation and refilling etc., and making connection to Manholes / Gully trap, wherever necessary and making chipping good portion to the original condition, complying with standard specification etc.,complete.

110mm dia. 6kg class III-pipes.

Supply, laying and erection of glazed stone ware gully trap (100 x 75 mm) with 100 mm dia, outlet including embedding trap in cement concrete 1:3:6 and constructing chamber of size 300 x 300 mm inside clear in brick masonry 230 mm thick, plaster with water proof cement mortar (1:3) 15 mm thick on both internal and external surfaces inside finished with floating coat of neat cement. The work including excavation to required depth of gully trap and refilling and making good in the surface with Providing and fixing SFRC frame and cover 400 x 400 mm (clear opening) complete complying with std. specification.

Supplying and Erection and construction of sewer chambers of required internal dimensions 600x600 upto 0.6 mtr.depth with 230mm brick masonry in C.M.1:5 thk of masonry over bed of 1:2:4 R.C.C. 200 mm thk bove 100 mm thk P.C.C.1;3:6 Cement concrete foundations over sand bed of 100mm thk channelling in 1;2:4 cement concrete, plastering in 1:3 cement mortar for internal and external surface finished with floating coat of neat cement, the work including excavation for required depth of gully trap and refilling and making good in the surface with SFRC cover and frame 600x600mm (clear opening)complete complying with standard specifications etc.,

PART-C WATER SUPPLY SYSTEM

Internal Concealed Works

Providing, supplying & laying of Unplasticized Poly Vinyl Chloride (UPVC-SDR-11) Pipes conforming to IS 15778 having thermal stability cold water with brass and UPVC fittings like Elbow,Brass Tee, Brass Elbow,Offsets,Tee with clamps @1.00 meters spacing, with jointing of pipes with one step UPVC solvent cement with including cutting of chase including testing of the joints complete and making good the walls etc.Rate is inclusive of all material labour, transportation,tools & tackles taxes,levies VAT etc all complete as per as per specifications,Concealed work including chase cutting) complete complying with standard specification and as directed by the Departmental Officer.

20 mm nominal (OD) pipes

25 mm nominal (OD) pipes

32 mm nominal (OD) pipes

PART-D.EXPOSED PLUMBING WORKS

Providing, supplying & laying of Unplastiized Poly Vinyl Chloride (UPVC-SDR-11) Pipes conforming to IS 15778 having thermal stability cold water with brass and UPVC fittings like Elbow,Brass Tee, Brass Elbow,Offsets,Tee with clamps @1.00 meters spacing, with jointing of pipes with one step UPVC solvent cement with including cutting of chase including testing of the joints complete and making good the walls etc.Rate is inclusive of all material labour,transportation,tools & tackles taxes, levies VAT etc all complete as per as per specifications, Exposed work including chase cutting, bracket fixing)complete complying with standard specification and as directed by the Departmental Officer.

20mm nominal(OD) pipes

25mm nominal(OD) pipes

50mm nominal(OD) pipes

40mm nominal(OD) pipes

50mm nominal(OD) pipes

Supplying and Errection of Electrically drivenwater lubricated vertical turbine pumpsets having discharge and head having from 150 lpm to 470 lpm , 10m to 60m head monoblock pumpset (5HP) PWDSoR, Unique code no. M 1065

Providing, supplying & laying of Gunmetal type NRV - pressure rating less tahn 16 Kg/Sqcm and IS778 with 2 Nos of MTA with jointing material like shellac, thread including testing of the joints complete and making good the walls etc. Rate is inclusive of all material labour, transportation, tools & tackles taxes, levies VAT etc all complete as per as per specifications, complete complying with standard specification and as directed by the Departmental Officer.

20 mm Dia

40 mm DIA

50 mm DIA

PART-E. EXTERNAL PLUMBING WORKS

Providing, supplying & laying of Unplastiized Poly Vinyl Chloride (PVC) Pipes conforming to IS 15778 having thermal stability cold Metro water with brass and PVC fittings like Elbow, Brass Tee, Brass Elbow, Offsets, Tee with clamps @1.00 meters spacing, with jointing of pipes with one step PVC solvent cement with including cutting of chase including testing of the joints complete and making good the walls etc.Rate is inclusive of all material labour,transportation, tools & tackles taxes, levies VAT etc all complete as per as per specifications,Concealed work including chase cutting) complete complying with standard specification and as directed by the Departmental Officer.

32mm PVC pipes

110mm PVC pipes

Cubical Arragements

BDO Table & Engineer Room : The Main Table of Size : 1500mm (L) x 600mm (D) x 750mm (H) and side table of size 900mm x 450mm x 750mm (H) and back credenza of size 1800mm x 450mm x 750mm(H) The Table top made out of 25mm thick particle board and 0.6mm decorative laminate finish with postformed finish. And back credenza having storage made out of 18mm thick pre laminate board duly edge banded with 2mm thick PVC edge beeding swing type shutters and lock and key arrangments. Having a mobile pedestal of size 400x 450x 640mm

Deputy BDO Overseer & L.F Audit Table : The Main Table of Size : 1600mm (L) x 600mm (D) x 750mm (H) and having side table cum storage unit of size 900mm x 450mm x 750mm (H) The side table having a two drawer on top bottom with swing type shutters with lock and key arrangements. The Table top made out of 25mm thick particle board and 0.6mm decorative laminate finish with postformed finish.

Modular Workstation: ‐ 75mm thick : Fabricated out of exclusive Aluminum sections with the following Specifications, (a) All the aluminum sections will be of 1.8 mm to 2 mm thick i.e., depends on the load bearing requirement. (b) The top cover & end cover will be of 75 mm breadth. (c) The electrical raceway cover will be of 100 mm width & 9 mm thick pre laminated / laminated particle board. (d) The tiles will be provided on both sides of the frame are fabricated out of 9 mm thick pre laminated board for tiles & MDF board for white marker board & Magnetic fabric board. (e) The two way, three way & Four way pillars will be fabricated out of 2 mm thick, 75 mm, Square Aluminum sections. (f) All the frames will be connected using bolt & nuts. (g) All the Aluminum sections will be duly powder coated in approved shade after necessary treatment. Table Top and Divder Pannel made of 25 mm thick edge banded with 2mm thick PVC Edge Beeding of Size 1100mm X 750mm x 1200mm (H) . having a mobile pedestal and key board tray

Slotted angle rack of size 1000 X 750 xX 2400 mm (H) 8 shelevs making 7 compartment The angle made of 80 x 40 x 2.5mm thick and panel made of 16SWG with bottom 2 nos horizontal strip .These racks are made from heavy duty slotted angle rack with necessary dipped paint finish and Shelves are 18 SWG made of multiple bends.Right angles are obtained by the use of corner brackets. The racks are covered with 0.8mm thick gladding sheet covered by three sides

Executive Chair Model Jupiter High Back for BDO Table & Engineer Room . The chair are Glass filled nylon base with twin wheel nylon castors and 120mm Gaslight for seat height adjustment. Synchronised multi‐function mechaism.Glass filled nylon backrest with Korean mesh. Seat upholstered with PU module foam and approved fabric. Tested as per ANSI/BIFMA standards. 4D swivel and height adjustable armrest with PU pad

Dynamic Medium Back Chair for Deputy BDO Overseer & L.F Audit : Glass filled nylon base ,Gaslift,twin wheel nylon castors , T Type adjustable PU armrest .back :ABS with mesh upholstery Synchro tilt mechanism , inbuilt lumbar support,seat PU moulded cushion twin wheel nylon castors and 120mm Gaslight for seat height adjustment. Synchronised multi‐function mechaism.Glass filled nylon backrest with Korean mesh. Seat upholstered with PU module foam and approved fabric. Tested as per ANSI/BIFMA standards. 4D swivel and height adjustable armrest with PU pad

Ground floor

BDO Table & Chairman Room : The Main Table of Size : 1500mm (L) x 600mm (D) x 750mm (H) and side table of size 900mm x 450mm x 750mm (H) and back credenza of size 1800mm x 450mm x 750mm(H) The Table top made out of 25mm thick particle board and 0.6mm decorative laminate finish with postformed finish. And back credenza having storage made out of 18mm thick pre laminate board duly edge banded with 2mm thick PVC edge beeding swing type shutters and lock and key arrangments. Having a mobile pedestal of size 400x 450x 640mm

Deputy BDO Overseer & L.F Audit Table : The Main Table of Size : 1600mm (L) x 600mm (D) x 750mm (H) and having side table cum storage unit of size 900mm x 450mm x 750mm (H) The side table having a two drawer on top bottom with swing type shutters with lock and key arrangements. The Table top made out of 25mm thick particle board and 0.6mm decorative laminate finish with postformed finish.

Modular Workstation for Section Office: ‐ 75mm thick : Fabricated out of exclusive Aluminum sections with the following Specifications, (a) All the aluminum sections will be of 1.8 mm to 2 mm thick i.e., depends on the load bearing requirement. (b) The top cover & end cover will be of 75 mm breadth. (c) The electrical raceway cover will be of 100 mm width & 9 mm thick pre laminated / laminated particle board. (d) The tiles will be provided on both sides of the frame are fabricated out of 9 mm thick pre laminated board for tiles & MDF board for white marker board & Magnetic fabric board. (e) The two way, three way & Four way pillars will be fabricated out of 2 mm thick, 75 mm, Square Aluminum sections. (f) All the frames will be connected using bolt & nuts. (g) All the Aluminum sections will be duly powder coated in approved shade after necessary treatment. Table Top and Divder Pannel made of 25 mm thick edge banded with 2mm thick PVC Edge Beeding of Size 1100mm X 750mm x 1200mm (H) . having a mobile pedestal and key board tray

Slotted angle rack of size 1000 X 750 xX 2400 mm (H) 8 shelevs making 7 compartment The angle made of 80 x 40 x 2.5mm thick and panel made of 16SWG with bottom 2 nos horizontal strip .These racks are made from heavy duty slotted angle rack with necessary dipped paint finish and Shelves are 18 SWG made of multiple bends.Right angles are obtained by the use of corner brackets. The racks are covered with 0.8mm thick gladding sheet covered by three sides

Drawing Room Meeting Table of size 3300 x 1400 x 750mm,The table made out of 25mm thick pre laminated particle board duly edge banded with 2mm PVC edge beeding having a one no pop up box without socket(Ground Floor and First Floor)

Executive Chair Model Jupiter High Back for BDO Table & Engineer Room . The chair are Glass filled nylon base with twin wheel nylon castors and 120mm Gaslight for seat height adjustment. Synchronised multi‐function mechaism.Glass filled nylon backrest with Korean mesh. Seat upholstered with PU module foam and approved fabric. Tested as per ANSI/BIFMA standards. 4D swivel and height adjustable armrest with PU pad

Dynamic Medium Back Chair for Section Office : Glass filled nylon base ,Gaslift,twin wheel nylon castors , T Type adjustable PU armrest .back :ABS with mesh upholstery Synchro tilt mechanism , inbuilt lumbar support,seat PU moulded cushion twin wheel nylon castors and 120mm Gaslight for seat height adjustment. Synchronised multi‐function mechaism.Glass filled nylon backrest with Korean mesh. Seat upholstered with PU module foam and approved fabric. Tested as per ANSI/BIFMA standards. 4D swivel and height adjustable armrest with PU pad

Supply and Fixing Wooden Partition of Aluminium Natural colour matt finish extruded box section Frame on 12mm thick Plywood with lamination on both side with 63.50mmx38.10mmx1.41mm at 0.818 Kg/m extruded box section at bottom, and Horizontal members on edges and vertical members are spaced at 60cm center to center and required height from floor level with necessary aluminium clips of size 19mmx17.30mmx0.90mm at 0.124kg/m, L angles, Screws etc., The aluminium surface is to be anodized with matt finish under electrically controlled condition in accordance with ISI1868/1962 specification for an average anodic film thickness. The rate is inclusive of cost of materials, conveyance scaffolding if any required etc. and necessary dismantling making holes in RCC brick masonry wherever with necessary with power drill to the extent required and made good to the original condition after fixing the partition as directed by the departmental officers. All materials should be got approved by the Executive Engineers before fixing in positions and complying with relevant standard specification, as directed by the Engineer-in-charge.

Providing & fixing Teakwood Frame 3"x2"With 30mm thick solid core flush with 85 x 15mm beech wood jamb alround and 12 x 12mm button beading fixed with 1 mm laminate (dark for bands and light for body) on both sides and 8mm clear float glass with etching design as directed with 50 x 15mm beech wood jamb alround the glass opening and 12 x 12mm beech wood beading for fixing of glass on both sides including necessary hardware viz., door stopper, door closure, door set lock (Godrej etc.,)handles, brass hinges of approved make & equality meala mine spray polish finish to all beech wood members etc., complete as directed. including cost of materials, labour charges, transportation charges etc all complete in all respects complying with relevant standard specifications and as directed by the departmental officers.

Main Door in Teak Wood

Earth work excavation for foundation & drain in all soils and to full depth as may be directed except rock requiring blasting but inclusive of shoring strutting and baling out water wherever nessery etc

Supplying and filling with M.sand in layers of not more than 15cm thick for foundation

Cement Concrete 1:4:8, using 40mm metal including all cost of materials & labour charges etc., complete

Brick work in cm 1:5 using country bricksincluding all cost of material & labour charges etc., complete.

Plastering with cm 1:5 mix 12 mm thick for all RCC floor including all labour charges etc.,

Supplying and fixing of Anti-Skid tiles for approved quality including cost and labour fixing charges etc.,complete.

supplying and fixing of 50mm SS hand rails vertical support of 50mm SS pipe, including all cost of material to site and labour charges etc…complet

ELECTRICAL

Internal Electrification

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) ( 5 points / Coil)

Wiring, testing and commissioning of 2Rx1.5 +1Rx1sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe with 2 mm thick, ISI marked concealed in ceiling with PVC accessories for additional light (Secondary)

Wiring with 3 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point Higher End

Lift Shaft Wiring : Wiring, Connecting, Testing & Commissioning for lift well light point and 6Amps power socket outlet with 2 x 2.5 sqmm FRLS PVC insulated stranded copper conductor of 1100V grade along with 1 x 2.5 sqmm FRLS PVC insulated standed copper conductor cable as earth wire in MS conduit including providing and fixing switch box, 2 Nos. of 5A single way module switch (for controlling light point and socket Outlet ) for each floor of the lift well , with bulkhead lamp 1 No. 5A 5 Pin shuttered socket outlet with flush type switch for each floor of the lift well and making necessary connections complete etc.

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections

Supply and fixing of 2nos.6A two module 5 pin socket , 2 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections

Supply and fixing of 2 nos.6A two module 5 pin socket , 2 nos. 6A one module switch on suitable module surface mounting Box ( Plastic ) with module cover plate (plastic) on wall with connections.

Supply and fixing of 3nos.6A two module 5 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections

Supplyandfixingof20AFlushtypeWall Socket32ADPMCBcompleteset forACPlug influshwithwallwithearth connection (For AC Plug)

Run of Mains

Supply and run of 4 x 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V on 7 / 20 GI bearer wire for service connection mains

Supply and Run of 2 of 2.5 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour.

Supply Wiring, run Connecting, Testing & Commissioning of 2 of 4 sq.mm PVC Insulated SC Unsheathed CU.Condutor of 1100V Grade in Suitable PVC Rigid Pipe Concealed in Wall and Ceilling With Continous Earth Wire Connection of 2.5 Sq.mm PVC insulated Sc CU.Condutor and making Good of the Concealed Portions With Suitable Colour. ( Rawpower 6 / 16Amps Socket & Split Ac unit Point Wiring). (Split Ac unit Point Wiring-2TR UNIT.)

Supply, run, testing and commissioning of 3CX2.5sqmm PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in existing floor raceways/PVC rigid pipe with 2 mm thick, ISI marked concealed in floor/wall and

Supplying, installation, testing and commissioning of 1200 mm (48") sweep AC ceiling fan complete with modular type stepped electronic 300W regulator, with 1 metre down rod with all required accessories.including point wiring

Supplying, installation, testing and commissioning of 375 mm (15") sweep (heavy duty) AC exhaust fan complete without provision of holes in the wall including all required accessories.

Supply and fixing of 7 segment 6 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 6 ways in one segment) (3x 6 ways in each segment) and seperate provision for MCB / Isolators ( totally 18 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only.

Supply and fixing of 7 segment 8 way 63A TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in each segment) and seperate provision for MCB / Isolators ( totally 18 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only.

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 40A 4P MCB Isolator as incoming and 4 nos. 32A TP MCB as outgoing in flush with wall with earth connection only.(MLDB)

ADD 4NOS 40A TP MCB

Lighting

Supply and fixing of single box type 4'36W fluorescent fitting complete with electronic ballast with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting

Supply and fixing of single box type 4'22W LED fitting complete with built in driver and clamps to fix on wall or ceiling with PVC unsheathed Copper leads from terminals to the fitting

supply and fixing of 18W LED square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of fancy glass shade and 7W / 9W LED bulb

Supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of WT bulk head fitting with guard suitable for 11W CFL lamp with CFL

supply and fixing of 30W LED street light fitting with LED (Higher end) with 25 mm dia. GI pipe (class B) with 1 no. 25 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting .

Supply and laying of following XLPE armoured LTUG cable in a trench/Tray with suitable cable tie tag etc as required.

3.5CX70sqmm Al. armoured LTUG Cable

3.5CX25sqmm Al. armoured LTUG Cable

Supply and fixing of double compression brass cable gland for following Aluminium conductor XLPE insulated armoured cable of 1100 V grade with earth connection.

3.5CX70sqmm Al. armoured LTUG Cable

3.5CX25sqmm Al. armoured LTUG Cable

Supply and installation of following size of GI Ladder / preforated cable tray including pre fabricated horizontal and vertical bends, reduces, tees, cross members with 300 mm spacing and other accessories as required and duly suspended from the ceiling, wall with MS angles, channels, suspenders, including painting, anchor fasteners, civil works etc., as required as per specification.

150X50mm Perforated Tray

Earthing

EarthingaspertheISIspecificationwithanearthelectrodeof2.10metreClass'B'GIpipeofdianot lessthan40mm with copper earth plate of size 125mmx 50mmx 6mmwithnecessary funneling arrangementswithnecessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply, fabrication, of GI /Copper earth flat of following size in provided trench, clamping in wall, ceiling, with suitable Clamps/ saddles, connecting the joints through bracing / welding covering with bitumen paint including accessories wooden plugs, screws, fastener etc., all inclusive

25mm x 3mm GI Flat

No8 SWG GI

LT PANELS

LT Metering Panel -Supply and fixng of TNEB meter board suitable for 3 phase 100A service connection made up of suitable angle iron frame work of size 2 feet x 1-1/2 feet using angle iron of size 1-1/2" x 1-1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1-1/2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos. 100A fuse units (500V), 1 No. neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 16 Sq.mm PVC insulated copper wire with earth connection complete

Main Panel - Supply, Installation, Testing and Commissioning of CPRI approved make of panel, cubicle type, Free standing, floor mounted, single front, 14 SWG CRCA sheet steel, enclosed separate compartment for each feeder, front operated, Powder coated, indoor type dust and vermin proof, hinged lockable doors, cluster LED type indicators, in the incoming feeders, complete with electrolytic grade aluminium bus bars, internal wiring, colour coding, ferrules, cable gland plates, Aluminium earth bus for the entire length of the panel with bonding to earth, Panel mounting MS Channels, fasteners, etc., including all associated control wiring. The panel details as follows:-

Safety Accessories

2m x 1m Rubber Mat suitable for 11 KV installation confirming to IS

First Aid Box complete with all First Aid Medicines

Shock Treatment Chart fixed in glass frame

Danger Board as required by the Electrical Authorities

Fire Extinguisher Co2, 4.5 kg. confirming to TAC Norms

UNDER GROUND SUMP - Size 4x3x1.5 - 18000 lts capacity

Earthwork for foundations and depositing on bank with initial lead of 10 Mt. and initial lift of 2 Mt. in sand, silt or other loose soil, wet sand or silt not under water, light black cotton soil, sandy loam and ordinary soil including excavated earth.

Supplying and filling in foundation and basement with m sand in layers of not more than 10cm thick well watered, rammed and consolidated etc., complete as per standard specification.

Laying the Plain Cement concrete 1:4:8(One cement four sand and eight broken Machine crushed stone jelly) using HBG Machine creased Machine crushed stone jelly of size 40mm gauge for founding and basement including de- watering if found necessary and laid in layers of not more than 15cms thick etc., complete complying with standard specification and as directed by the departmental officers. The rates inclusive of Centering , shuttering, strutting, propping,removal of form work if it is required and all leads ,lifts and curing etc..

Supplying and Erecting centering for sides and soffits including necessary supports and strutting up to 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specification. (Payment for centering shall be given after the concrete is laid)

Providing and laying in position machine batched,machine mixed and machine vibrated design mix cement concrete of M25 grade for reinforced cement cement ratio with plasticiser using 20mm and down concrete structural elements under controlled water graded machine briken grnite stone jelly excluding the cost of centering and shuttering and reinforcement but including curing, fixing, fan clamps etc., as per standard specification and as directed by the depart- mental officers comple.-1m3

Supply, fabrication and placing of reinforcement steel of high yield strength ribbed bars of various diameters and grade conforming to IS 1786 for reinforced concrete work. The work includes recoiling, straightening, cutting, bending, fabricating, and placing in position, at all levels including lead and lift, according to drawings, specifications etc. complete and supply & use of 18G black annealed binding wire double fold to tie the bars in position and providing precast cement/ PVC cover blocks for main reinforcement to ensure specified cover and complete., including all labor charges etc as directed by departmental officers.

Providing, supply, mixing laying cement plastering 20mm thick with cement mortar 1:4 mixed with water proofing compound Conplast X421IC conforming to IS:2645, @ 150ml per bag of cement (normal setting integral water proofing compound) as specified by the manufacturer over PCC leveling course including preparation of surface, dewatering, finishing, curing etc. all complete as per manufacture's Specification and direction

Supplying, laying and fixing in position ceramic tiles of approved size , quality and colour set k in CM 1:3 - 20 mm thk. Including cutting the tiles to the required size with special cutter where ever necessary and pointing the joints with coloured cement using 0.40 Kg / Sqm including finishing the flooring and pointing the joints flesh with tile surface etc.complete.Basic cost-Rs.464/sq.m

Supplying and fixing in position C.I.Manhole covers (heavy duty) of various sizes of best approved quality and as per standard specificationsetc.,complete.0.6X0.6M Size etc., complete.

PVC mould CI steps for sump

SEPTIC TANK

Earth work excavation in all soil and subsoil to full depth as directed exert hard rock etc complete

Cement concrete 1:4:8 mix for foundation using 40mm ISS HSG metal including all charges etc

Providing and laying in position, Standardised Concrete Mix M-25 Grade in accordance with IS:456-2000, using 20mm and down grade hard broken granite stone jelly for all RCC Items of works with minimum cement content of 350kg/m3 and maximum water cement ratio of 0.50, including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS:9130 to accelerate, rated setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m) 7730kg. of 20mm machine crushed stone jelly and with about (3.3cum) 5156 kg. of 10-12mm machine crused stone jelly and with about (4.79cum) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with Mechanical vibrators, finishing, curing, etc.,and providing fixtures like fan clamps in the RCC Floor / roof slabs wherever necessary without claiming extra, etc., Complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No Separate payment will be made by the Department for the excess usage of materials).

Supplying and Erecting of water tight steel Shuttering and cutering including necessary supports including all labour charges etc

Supply and Fabrication of steel for all RCC works including all charges etc

Special plastering with CM 1:3 to 10mm thick including all charges etc completed

Providing Manhole Cover including all etc

PVC mould CI steps for sump

Providing, machine mixing and laying on the P.C.C/ R.C.C. surface in approved panels of 40 mm thick granolithic flooring in cement concrete mix of 1:2:4 (1 Cement: 2 Sand: 4 Aggregate 10 to 12 mm thick) well vibrated,compacted including 45 X 3 mm glass dividing strip, fixed to correct level and finished smooth and cured by keeping surfaces well-covered and protected against excess of an type. (The contractor to provide for preparation of surface by cleaning, hacking and exposing aggregate to achieve the best bond and any curling, lifting or beybonding noticed shall be rectified by the contractor at his cost).

Brick partition wall of 11cm thick using country bricks of size 8 3/4 x 4 1/4 x 2 3/4" in cement mortar 1:3 (One cement and three sand) using hoop iron reinforcement if found necessary including finishing and curing etc., complete.

Signboards Brailey

RAIN WATER HARVESTING

Earth work Excavation for Foundation in Hard soil to full depth as may be directed except in hard rock requiring blasting but inclusive of shoring strutting and requiring the sides of foundation, etc., complete as per standard specifications

Supplying and filling the recharge Pit with following materials as per standard specifications

40 mm metal

20 mm metal

Coarse Sand

Cement Concrete 1:4:8 mix using 40mm ISS metal including cost and conveyance of all materials to site and all labour charges etc., complete as per standard specifications

Brickwork in CM 1:5 mix using II class bricks of size 23 x 11 x 7 cm for the following including curing etc., complete as per standard specifications

Plastering with cement mortar 1:5 mix to 12 mm thick including cost and conveyance of all materials to site and all labour charges etc., complete as per standard specifications

Supplying and fixing PVC pipes for rainwater arrangements of following dia meter including cost of specials like bend,shoe,bracket etc., complete.

Supply of following PVC specials etc.,

110 mm Elbow with door

110 mm Tee

110 mm Elbow

Provision for CI cover slab

Compound Wall

Earth work excavation for foundation in all classes of soils and sub soil to full depth except in hard rock requiring blasting but inclusive of shoring strutting if required for the sides of foundation.

Cement Concrete 1:4:8 using 40 mm HBG metal for basement and flooring layers not more than 15 cm thick including cost and conveyance of materials to site and all other labour charges including consolidation as per standard specification

Supplying and erecting centering shuttering including necessary supports for plane surface in foundation and basement and in all floors for R C C column footing column plinth beam, beams, roof slabs, staircase steps, bed blocks, critical pier including all cost and conveyance etc.

Above GL

Supplying and fabrication of steel including cost and conveyance of steel to site and all labour charges for straightening, cutting to length,bending to shape and tying in position and forming grills for all R.C.C works.

Brick work in cement mortar 1:5 mix using country bricks 83/4"x43/8"x23/4"conveyance of all materials to site and all labour charges etc complete

Plastering in CM 1 : 5,12 mm thick , including cost and conveyance of all materials to site and all other labour charges including curing etc., as per standard specification.

Painting Two coats with approved Emulsion paint including cost conveyance to site and labour charges etc., complete.

Provision for Steel Gate

Lift Shaft Wiring

Lift Shaft Wiring : Wiring, Connecting, Testing & Commissioning for lift well light point and 6Amps power socket outlet with 2 x 2.5 sqmm FRLS PVC insulated stranded copper conductor of 1100V grade along with 1 x 2.5 sqmm FRLS PVC insulated standed copper conductor cable as earth wire in PIS conduit including providing and fixing switch box, 2 Nos. of SA single way module switch (for controlling light point and socket Outlet ) for each floor of the lift well , with bulkhead lamp 1 No. 5A 5 Pin shuttered socket outlet with flush type switch for each floor of the lift well and making necessary connections complete etc.

Supply and Installation of 20 Amps DP Switch In Enclosure for Lift Car Liohtino And Lift Pit Liohtino

63A TPN NCCB for Lift Plotor

4C X 10 Sq MN LTUG cableCable Fo' Lift Motor

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class'B' GI pipe of dia not less than 40mm with copper earth plate of size125mmx50mmx6mm with necessary funne lingarrangements with necessary masonry work and with 38mm RCC cover slab for the brick

Supply, fabrication, of GI /Copper earth flat of following size in provided trench, clamping in wall, ceiling, with suitable Clamps/ saddles, connecting the joints through bracing / welding covering with bitumen paint including accessories wooden plugs, screws, fastener etc., all inclusive

25mm x 3mm GI Flat

No8 SWG GI

Supply & Installtion of Lift

Sencer Lift MRL, Speed 1.5 m/s th Stainless steel Panels, Disable friendly, croprocessor based ntroller, WVF drive, Fire rated doors nrl A D M- D Pr•rcnnc: (Add for every additional Floor over G+3 Floors - Rs.1,00,000/-

GST Amount for providing service to Government contract works for the above construction works. { GST amount is the Total GST amount for total overall quoted amount above this row in column "BB" for all works in this package}

R SURESHMANI (BID ID -1394476)