CA NO CWE BTD 05 of 2020-21 Special repairs to Bldg No P-709 (OR Living) at Bathinda Mil Station under GE (North) Bathinda

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area not exc 1.5 Sqm each and removing from site including cutting holes for removal of hold fast complete.

S & F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as specified in Preamble 8B.3.1 of SSR Part -II (2010) and all as shown on drawing of SSR Part-II (2010).

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement all as per instruction and drawing shown for item No 8080 of SSR Part II.

S & F 100 mm long aluminium anodised, barrel tower bolts of extruded section.

S & F butt hinges, medium weight, cold rolled mild steel , size of hinges 75mm.

S & F 100mm extruded aluminium alloy handles, cast type, anodised.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm but not exc 4 Sqm each and removing from site including cutting holes for removal of hold fast complete.

S & F factory made pressed steel frames for door with one or more rebates including necessary fixing lugs, lock strike plate, hinges etc, compete, all as specified of frame size 105 mm x 60mm & thickness of MS sheet shall not be less than 1.25 mm including making holes for fixing hold fast etc and making good the wall with plaster in cement mortar (1:6) complete.

S & F factory made pressed steel frames for door with one or more rebates including necessary fixing lugs, lock strike plate, hinges etc, complete, all as specified of frame size 125 mm x 60mm & thickness of MS sheet shall not be less than 1.25 mm including making holes for fixing hold fast etc and making good the wall with plaster in cement mortar (1:6) complete.

M & L for PCC (1:3:6) type C-0 using 12.5 mm graded stone aggregate in filling in chowkats/ door frame or bed block of hold fast and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete.

Taking down shutters of any description exceeding 1.00 Sqm but not exceeding 2.00 Sqm each and removal from site.

S & F 35mm thick factory made panelled shutter (two panel) plain framed with lock rail and panel of 12mm thick veneered particle board with commercial veneering on both faces conforming to IS-3097 exterior grade kiln seasoned and chemically pressure treated of second class hard wood rails and styles and the size of rail and style as per IS-1003 (Part I).

S & F factory made glazed and skeleton shutters 35mm thick using second class hard wood open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc; sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24(a); all as specified complete.

S & F mild steel barrel tower bolts, stove enamelled black, with bright bolt, length of bolt 200mm.

S & F butt hinges, medium weight, cold rolled mild steel , size of hinges 100mm.

S & F 125 mm mild steel pressed handles, oval type, stove enamelled black.

S & F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm.

S & F mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, length of bolt 250mm.

S & F 300 mm long MS ordinary rat tail rod pattern springs for doors including roller and roller plate complete.

S & F mild steel galvanized wire cloth, 0.56 mm nominal dia of wire & average width of aperture 1.18mm and fixed with galvanized steel wire staples complete.

S & F in repairs mild steel galvanized wire cloth, 0.56 mm nominal dia of wire & average width of aperture 1.18mm and fixed with galvanized steel wire staples complete.

S & F factory made steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded including one shop coat painting including dismantling of old existing window as directed.

S & F factory made steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete without glazing bars, dovetailed or welded including one shop coat painting including dismantling of old existing window as directed.

S & F factory made steel ventilator with top hung shutter incl hinges, steel pegs and stay with glazing bar complete including dismantling of old existing window/ ventilator as directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins / spring clips of size not exceeding 0.5 Sqm each pane complete.

S & F sheet glass, 4 mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane fixed with oil putty or wooden beads including Provn of glazing pins/spring clips wherever necessary.

S & F figured pin headed glass, 4 mm thick ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane fixed with oil putty or wooden beads including Provn of glazing pins/spring clips wherever necessary.

M & L for painting to new steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces.

M & L for painting to new wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces.

Supply only liquid water proofing material, ISI marked.

S & F in repairs vitreous china squatting pan, 'Orissa' pattern, size 580mm x 440mm, white, with integral foot rests including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. including making good to floor and excluding flushing cistern, flush pipe and waste pipe complete.

S & F in repairs PVC valveless, syphonic action type, flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle including brackets and PVC flushing pipe 32mm dia complete.

S & F in repairs vitreous china wash hand basin, countersunk in granite slab , white, of size 300mm x 450mm , excluding waste, chain and plug and porcelain stopper but including 32 mm dia waste coupling fancy type chromium plated and PVC waste pipe of 32 mm dia and fixed all as directed complete, .

Supply only 15mm bore chromium plated, fancy type, quarter turn Pillar cock screwed down high pressure, with or without lettered Hot ot Cold with long screwed shanks and flynuts screwed for iron pipe complete all as specified.

S & F in repairs, vitreous china urinal,half stall type, white with grating and union for discharge pipe including waste pipe and providing and fixing plugs bedding urinal against wall in cement mortar (1:2) securing urinal to plugs with and including connections to flushing pipe and out pipes complete .

S & F in repairs, PVC connections 15 mm bore, 450 mm length, heavy duty, with PTMT nuts.

S & F in repairs, stainless steel chromium plated soap tray of size 160 x 160 x 90mm and fixed on wall with chromium plated brass screws complete.

S & F in repairs brass chromium plated shower rose 125 mm size with or without swivel joints fix to steel pipe or union complete all as specified and as directed.

S & F in repairs stop valves, chromium plated, fancy type, quarter turn, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 15 mm bore dia of pipe.

S & F in repairs stop valves, cast copper alloy, fancy type, quarter turn, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions for 15 mm bore dia of pipe.

S & F in repairs, 15 mm bore chromium plated, fancy type, quarter turn, bib taps cast copper alloy with crutch or butterfly handle, screwed for iron pipe, or for brass ferrule complete all as specified and as directed.

S & F in repairs, stainless steel, chromium plated tubular towel rail, 20 mm dia, D type, 450 mm long between flanges fixed with CP screws and wooden cleats.

M & L for 15 mm bore GI pipe, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors including taking up or down 15 mm bore existing steel tubing and connections complete.

Taking up or down 15 mm bore existing steel tubing and connections complete and re-fixing the same in new or old position to walls and ceilings or laid in floors including cleaning of pipe and provision of new fitting as required complete all as directed..

M & L for 20 mm bore GI pipe, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors including taking up or down 20 mm bore existing steel tubing and connections complete.

Taking up or down 20 mm bore existing steel tubing and connections complete and re-fixing the same in new or old position to walls and ceilings or laid in floors including cleaning of pipe and provision of new fitting as required complete all as directed..

M & L for non skid coloured ceramic tiles of size minimum 400mm x 400mm, 7 to 8 mm thick (square/rectangular), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile with including 15 mm thick Screed bed or bedding layer in CM (1:6) including dismantling existing floor tiling including cement mortar bedding and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified. Note: Only course sand shall be used in screed bed.

M&L for non skid coloured ceramic tiles of size minimum 300mm x 300mm, 7 to 8 mm thick (square/rectangular), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile with including 15 mm thick Screed bed or bedding layer in CM (1:6) including dismantling existing floor tiling including cement mortar bedding and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified. Note: Only course sand shall be used in screed bed.

S & F glazed ceramic coloured tiles 450 x 350mm, 7 to 8mm thick in verticle surfaces such as dado / skirting, set and jointed in neat cement slurry and pointed in white or coloured cement pigmented to the match the shade of tiles laid over and including 10 mm thick rendering in cement mortar (1:4) as backing coat and finish the surface rough to receive the tile including dismantling existing hearth or wall tiling including cement mortar bedding (but not backing) etc on brick or stone walls etc including racking out joints hacking for key and scrubbing removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified.

M & L for machine cut kota stone slab flooring minimum size 450 mm x 450 mm, 18 to 20 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing laid over and including 20 mm thick Screed bed or bedding layer in CM (1:6) complete.

All as per item No 51 above but in vertical surfaces such as skirting as directed at site including 10 mm thick rendering as backing coat in cement mortar (1:4) all as directed.

S & F PVC (SWR) 110mm bore pipes, single socketed, in any length with rubber ring joints, fixed to walls with and including MS clamps including taking down existing eaves gutters and rain water pipes (any size or pattern ), including all fittings, heads, shoes, bends, swan necks, etc. (measured overall as fixed along the centre line over fittings and accessories)

S & F 110 mm bore PVC (SWR) bends of any radius / shoe, fixed to PVC pipes as directed.

S & F grating doom 140mm dia of PTMT (minimum weight 50 gm) for floor trap.

S & F in repairs 100 mm dia cast iron floor trap with chromium plated grating incluing jointing to waste pipe fixed in cement concrete (1:2:4) type B-1, complete all as specified.

S & F in repairs 75 mm dia cast iron floor trap with chromium plated grating incluing jointing to waste pipe fixed in cement concrete (1:2:4) type B-1, complete all as specified.

S & F 100 mm bore cast iron (spun) soil, waste and vent pipes, ISI marked in any length with or without ears, with cement joints, laid in trenches or in floor or fixed to walls with and including suitable size clamps including dismantling of existing drain pipes, jointed in cement mortar all as directed.

S & F 75 mm bore cast iron (spun) soil, waste and vent pipes, ISI marked in any length with or without ears, with cement joints, laid in trenches or in floor or fixed to walls with and including suitable size clamps including dismantling of existing drain pipes, jointed in cement mortar all as directed.

S & F in repairs 100 mm dia cast iron branch pieces, single (equal or un-equal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete.

S & F in repairs 75 mm dia cast iron branch pieces, single (equal or un-equal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete.

S & F in repairs 100 mm bore cast iron bends (any radius), diminishing pieces or tapers (large bore measured) .

S & F in repairs 100 mm bore cast iron bends (any radius), diminishing pieces or tapers (large bore measured) with oval access door.

S & F in repairs 75 mm bore cast iron bends (any radius), diminishing pieces or tapers (large bore measured) .

S & F in repairs 75 mm bore cast iron bends (any radius), diminishing pieces or tapers (large bore measured) with oval access door.

S & F in repairs 100mm cast iron Cowl fixed with cement joint in CM 1:2 complete all as specified.

S & F in repairs 75mm cast iron Cowl fixed with cement joint in CM 1:2 complete all as specified.

S & F in repairs SGSW Gully trap of size 150 x 150 mm, set and jointed to drain in CM 1:1 complete all as specified.

S & F in repairs Stack clamps made out of 50 x 5 mm flat iron and 16 mm dia round iron stay including nuts , bolts and securing ends of stays to wall or roof complete for 100 mm bore dia pipe all as specified.

M & L for rendering 15 mm thick in cement mortar (1:6) on internal wall surfaces of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement including taking down old cement plaster including raking out joints hacking for key scrubbing down with water etc and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified.

M & L for rendering 15 mm thick in cement mortar (1:4) on external wall surfaces of brick work or concrete surfaces even and fair without using extra cement mixed with liquid water proofing material as per manufacturer's instruction including taking down old cement plaster including raking out joints hacking for key scrubbing down with water etc and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified. (Liquid water proofing material shall be measured and paid for separately.)

M & L for rendering 5 mm thick in cement mortar in (1:3) finishing the surfaces even and smooth on ceiling including taking down old cement plaster and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified.

M & L for rendering 5 mm thick in cement mortar in (1:3) over 10 mm thick in cement mortar (1:4) as additional / floating coat on concrete surfaces of walls , chajjah , beams , ceiling etc even and smooth without using extra cement mixed with liquid water proofing material as per manufacturer's instruction including taking down old cement plaster and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified. (Liquid water proofing material shall be measured and paid for separately.)

M & L for precast cement concrete (1:2:4) type B1 using 20mm graded stone aggregate as in manhole cover, slabs of any thickness/ kerb stone etc, size or shape including necessary form work and set in CM (1:4) including demolition of existing RCC of any description complete all as specified.

M & L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

Demolition of brick tiles or terracing tiles, single layer on roofs including removing the demolished material exceeding 1 km and not exceeding 2 km away from site and disposal off in low lying area as directed.

Demolition of mud in roof, any thickness including plastering and leaping (where full thickness recovered or only a part there of) including removing the demolished material not exceeding 200 m away from site and disposal off in low lying area complete.

M & L for cleaning of top surfaces of concrete roof slab , lime terracing , or surface of tiles with wire brush including flashing and junction of parapets etc and surface painting with layer of blown grade bitumen of any penetration applied hot @ 1.70 Kg / Sqm and rendering in 15 mm thick in cement mortar (1:4), priming the surface @ 0.30 Kg / Sqm and laying 3 mm thick APP based polymer membrane of weighing not less than 3 Kg / Sqm reinforced with polyster non woven fabric (Weight not less than 150 Gm / Sqm) laid on primed surfaces by torch application as a treatment for moderate condition complete all as specified and as directed.

M&L providing 40 mm thick cement concrete in (1:3:6) type C2 using 40 mm graded stone aggregates as leveling course on roof slab.

Material and labour for 40 mm thick brick tiles laid on mud mortar or CM (1:6), 20 mm thick and joints grouted flush in CM (1:3) mixed with @ 5% of crude oil by weight of cement or mud phuska complete all as specified.

All as per item No. 80 but except brick tiles complete all as specified. Note :- Old serviceable brick tile to be reused after cleaning and washing.

S & F 1000 litres capacity Rotational moulded polyethylene in white colour, three layered, water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of old water tank of any size and any type and removing rubbish to a distance exceeding 1 km but not exceeding 2 km etc all as directed.

S & F ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe of size 20 mm bore (minimum weight 210 gram).

S & F in repairs Gun metal globe or Gate valve , with iron wheel , screwed both ends for iron pipe or for unions for 20 mm bore dia of pipe.

S & F in repairs Gun metal globe or Gate valve , with iron wheel , screwed both ends for iron pipe or for unions for 15 mm bore dia of pipe.

Demolition of PCC in ground floors and pavings not exc 15cm thickness (below or above ground level) and removing the debris to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified.

Demolition of PCC in ground floors and pavings exc 15cm thickness (above ground level) and removing the debris to a distance exceeding 1 km but not exceeding 2 km etc complete all as specified.

M & L for PCC (1:2:4) type B-1 using 20 mm graded stone aggregate as in coping , steps , bed block etc complete.

M & L Hard core of gauge not exceeding 63mm , using broken stone or boulder , deposited , spread & leveled In layer not exceeding 15 mm thick watered and rammed to a true surface complete.

M & L for 75 mm thick PCC (1:3:6) type C2 using 40mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement including demolition of existing PCC of any description complete all as specified..

Complete removal of existing treatment on wall (any number of layears) by scrapping with steel wire brushes or any other means, including filling depressions of scrapped surfaces and M & L for preparation of old plastered surfaces of walls and applying the following:- (i) Two coats of weather coat Apex paint (External emulsion) of approved tint by using airless spray / roller over and including a coat of acylic external primer. Note :- Contractor may use manual tools for surface preparation with prior approval of Engg- in- charge in writing in case use of mechanical equipments are not possible.

M & L for preparing newly plastered surfaces of walls and applying three coats of white wash all as specified..

M & L for preparing newly plastered surfaces of ceiling and applying three coats of white wash all as specified..

Digging out and removing sunken floor filling and depositing the same at a distance not exceeding 250 M where as directed complete all as specified .

M&L for sunken treatment to sunken floor, cleaning the surface by using wire brush, rendering to floor and sides with 10 mm thick cement mortar (1:4) including mixing of liquid water proofing material in mortar @ 3% of cement content, finished even and smooth without using extra cement after that material & labour for providing two coats of two components (one part liquid two parts powder) ready to use cementations water proofing coating on properly prepared surfaces by brushing having elongation of >50% for the applying water proofing treatment as per following on horizontal and vertical surfaces of sunken floor complete all as per manufacturers instruction. (i) Applying 1st coat of two components modified polymer coating. (ii) Providing glass fiber mess of 2 x 2mm immediately on alone coating. (iii) Apply 2nd coat of two components modified polymer coating after 72 hrs on horizontal and vertical surfaces.

NOTE FOR ITEM No 95 : (i) Complete treatment shall be carried out by authorised applicator of waterproofing manufacturer as given in Appx 'B'. (ii) Liquid water proofing material for mixing in cement mortar shall be measured and paid separately.

M & L for PCC (1:2:4) type B2 using 20 mm graded stone aggregate with using water proofing compound as per manufacturer's instruction as in sunken floor all as specified..

M & L for PCC (1:5:10) type E2 using 40 mm graded stone aggregate with using water proofing compound as per manufacturer's instruction as in filling & mass concrete in sub base , floor all as specified.

Internal Electrification

Taking down carefully existing unserviceable copper / aluminum point wiring (light, fan, socket) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, light fittings etc and removing the retrieved materials from site including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and directed.

M & L for point wiring with multi stranded copper conductor FRLSH cable, 1100 volts grade PVC insulated and unsheathed of size 1.5 Sqmm single core in existing PVC concealed conduit and including new MS sunken box and 3 mm thick bakelite laminated sheet top cover for one fan / exhaust fan / light controlled by one switch including provision of 1.5 Sqmm PVC insulated unsheathed with single core, multi stranded copper conductor FRLSH cable as earth wire to common earth & connecting to earth dolly all as specified and directed.

All as per item No 99 here in before but for socket outlet 5 pin, 6 Amp on same board complete all as specified.

All as per item No 99 here in before but for socket outlet 5 pin, 6 Amp on independent board but not below the switch board complete all as specified .

All as per item No 99 above but for one light point controlled by two , two way switches .

All as per item No 99 here in before but for one socket outlet 6 pin, 6/16 Amp multipurpose 2 in 1 on independent board with cable of 2.5 Sq mm, multi stranded copper conductor FRLSH cable including provision of 2.5 Sq mm PVC insulated solid copper conductor FRLSH cable continuos as earth wire connected to earth dolly, conductor etc.

M & L for point wiring with multi stranded copper conductor FRLSH cable, 1100 volts grade PVC insulated and unsheathed of size 1.5 Sqmm single core in and including PVC concealed conduit not less than 20mm dia ( medium duty ISI marked) and conduit fittings with and including 3 mm thick bakelite laminated sheet top cover for one fan / light controlled by one switch including provision of 1.5 Sqmm PVC insulated & unsheathed with single core, multi stranded copper conductor FRLSH cable as earth wire to common earth & connecting to earth dolly all as specified and directed.

All as per item No 104 here in before but for socket outlet 5 pin, 6 Amp on same board complete all as specified.

All as per item No 104 here in before but for socket outlet 5 pin, 6 Amp on independent board but not below the switch board complete all as specified .

All as per item No 104 here in before but for one socket outlet 6 pin, 6/16 Amp multipurpose 2 in 1 on independent board with cable of 2.5 Sq mm, multi stranded copper conductor FRLSH cable including provision of 2.5 Sq mm PVC insulated solid copper conductor FRLSH cable continuos as earth wire connected to earth dolly, conductor etc.

S & F Switch semi modular with frame, flush type, single pole, one way, 5/6 Amp .

S & F Switch semi modular with frame cover, flush type, single pole, two way, 5/6 Amp .

S & F Switch semi modular with frame, flush type, single pole, one way, 15/ 16 Amp .

S & F Semi modular socket, multipurpose, 2 in 1, 5 Pin, 6 Amp, flush type, including decorative frame cover. (Note: Switch and socket shall be of same make.)

S & F Semi modular socket outlet universal, multipurpose, 2 in 1, 3 Pin 6 Amp and 6 pin 16 Amp, flush type, including decorative frame cover. (Note: Switch and socket shall be of same make.)

S&F, fan regulator electronic step type (1-5), socket type 230-240 Volt, AC supply, complete all as specified and directed.

S&F ceiling rose, 3 plate, surface bakelite type, Polycorbonate body, 6 Amps, 250 Volts AC, 20x50 mm, three terminal (ISI marked) complete all as specified.

S & F, in repair, Lamp holder of PVC/Polycarbonate type with back plate suitable for batten fitting including 9 watt LED bulb.

S & F MCB, SP, 6 to 32 Amps, 'C' curve, 230 Volts, breaking capacity not less than 10 KA with over load and short circuit protection including taking down old unserviceable MCB SP complete all as specified.

S & F MCB, SPN, 40 Amps, 'C' curve , 230 Volts, 50 Hz, breaking capacity not less than 10 KA with over load and short circuit protection and including taking down old unserviceable MCB complete all as specified.

S & F MCCB, Four pole, 63 Amps, breaking capacity 25 KA thermal magnetic based including taking down old unserviceable MCB TPN complete all as specified.

S & F sheet metal enclosures double door made out of CRCA mild steel sheet, concealed, surface mounting, acrylic door, IP-43 protection, 8 way, DB SPN 230 Volts, with 200 Amp rated bus bar, dust and vermin proof suitable for fixing MCB's and Isolators etc including taking down old unserviceable DB.

S & F sheet metal enclosures double door made out of CRCA mild steel sheet, flush mounted, acrylic door, IP-43 protection, 4 way, DB TPN 415 Volts, with 200 Amp rated bus bar, dust and vermin proof suitable for fixing MCCBs , MCB's and Isolators etc including taking down old unserviceable DB.

M & L for sub main wiring with 2 single core cable PVC insulated unsheathed of copper multi strandard conductor FRLSH cable of size 6 sqmm, 1100 votls grade drawing through in and including PVC concealed conduit 20 mm dia medium duty including acessories such as Tee, bend, Elbow etc, ISI marked with and including PVC insulated 6 sqmm unsheathed multistranded FRLSH copper conductor cable for earth continuity and connected to common earth dolly including cutting chasing of wall, if required and making good disturbed surface in CM (1:3) and finishig the surface to match with existing surface etc including taking down old unserviceable wiring 6 Sqmm complete all as specified. Note:- Two runs of cable, one run of earth wire and one run of PVC conduit shall be measured as one unit.

M&L for sub main wiring with 2 single core cable 6 sqmm, 1100 votls grade PVC insulated unsheathed of copper multi strandard conductor FRLSH cable with continuous copper earth conductor of size 6 sqmm, 1100 votls grade drawing through in existing PVC concealed / surface conduit including taking down old unserviceable sub main wiring complete all as specified. Note :- Two runs of cable and one run of earth wire shall be measured as one unit.

S & F 18/20 watt Retro LED tube light fitting, wall/surface mounted, IP 20 protection, conforming to IS 16106/IS 16107, minimum 6000K batten decorative type 4 feet long polycarbonate body, white, in built LED driver, power factor>0.95 , Make – all as per Crompton Cat Part No. DMLN1LT8-16 (for batten) and Cat part No. LT8-20-865-2 (for tube light) including 18/20 watt tube rod or equivalent model of any make given in Appx 'B' connecting to electric point by using PVC insulated twin core copper conductor cable of suitable size including taking down old existing light fitting all as directed.

S & F LED mirror light fitting of 07 watt, 6000K, linear & compact with decorative grey end caps, polycarbonate body and ribbed opal diffuser complete including 07 watt tube rod all as Model No LCL- 07- CDL of Crompton with 07 watt rod or equivalent model of approved make from list of make attached in tender documents including connecting to electric point by using PVC insulated twin core copper conductor cable of suitable size including taking down old existing light fitting.

S & F energy efficient LED street light fitting of 25 Watt with PDC aluminium body and clear glass with lens for wide beam distribution, top maintainable type with IP 66 degree of protection, PF>0.95 with voltage range 140 to 270 Volt, fitting should be provided with inbuilt 5 KV minimum surge protection, short circuit and over voltage protection facility for Driver and fitting including 25 watt LED lamp with GI brackrt-01 No, MS clamp-02 Nos suitable for walls/ columns and making electrical connection with providing of 1.50 metre long twin core round copper conductor cable of suitable size and testing complete all as per SYSKA cat part No. SSK-SLF-CF-25W-WL or equivalent model of any make given in Appx 'B', Cat Part No. as approved by GE complete all as specified including taking down old unserviceable existing street light fitting of any type and capacity from pole along with accessories.

M & L in replacement of earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick burried directly in ground to depth of pit not less than 2.25 m below normal ground level with top edge of the plate not less than 1.5 m below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal / coal dust and common salt filling in alternate layers and connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of GI or steel including GI protection pipe 15mm dia light grade upto the extent of 7.5 metre and connecting to earthing test point, main switch board including GI pipe 20 mm dia light grade for watering, MS funnel and bringing out the watering pipe upto 30 cm above the normal ground level plugged at top including all fitting including PCC earth pit with PCC 1:2:4 type B-1 using 20mm graded stone aggregate and RCC pit cover including necessary earthwork and excavation in any type of soil complete all as specified as shown in electrical plate No 3 of SSR Part-I and testing on completion. Note :- (a) PCC chamber shall be constructed at least 1.5 m away from earth pit. Pipe for watering shall be provided in slanting manner. (b) 4mm dia GI wire and 15mm dia light grade GI protection pipe upto 7.5 metre shall deemed to be included in quoted rate.

M/s Kamal Builders

V K CONTRACTOR

M/s MITTAL CONSTRUCTIONS

M/s Kamal Constructions

M/s Balvinder Singh Engineer and Contractors

swarn singh and co.

M/s RAMESH KUMAR VERMA CONTRACTORS