R/Rain Damages for LWSS Giri khad to village upper Banahal in GP Bagain in JSV Sub-Division Sainj in tehsil theog Distt Shimla H.P.(SH-C/O Pump house Protection work for 2nd stage at village upper Banahal

Amount

Cutting in earth work in all kinds of soil such as pick work, jumper work, blasting work and chiselling work etc. and disposal of excavated earth as directed within all leads and lifts as per direction of Engineer-in-charge.

Prov. and laying cement concrete 1:4:8 (1cement:4sand:8graded stone agg. 40 mm nominal size)and curing complete excluding cost of form work i/c all leads and lifts and to the entire satisfaction of the Engineer-in-charge in :

Foundation and plinth.

Prov. and laying cement concrete 1:6:12 (1cement:6sand:12graded stone agg.40mm nominal size) and curing complete excluding cost of form work in: a) Foundation and plinth.

Prov. and laying cement concrete work 1:2:4(1cement:2sand:4 graded stone agg. 20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work i/c all leads and lifts complete in all respect. :-

Column, pillars posts and struts upto floor two level.

Suspended floors, roofs, landings,shelves and their supports balconies, beams, girders, bressumers and cantilevers upto floor two level.

Stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto floor two level.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden, battens, and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs.and removal of the same for insitu reinforced concrete and plain concrete work complete in all respect i/c all leads and lifts and to the entire satisfaction of the Engineer-in-charge.

Column Pillars, posts and struts square rectangular polygonal in plan.

Beams, cantilevers, girders and lintels:- Sides and soffits of beam, beam haunching scantilevers, bressumers and lintels not exceeding 1 mtrs. in depth in all height from floor.

Flat surfaces such as soffits of suspended floors,roofs, landings, and the like:-i)Floors etc. upto 200mm in thickness.

Slopping or battering surfaces including folded plates: Where inclination to horizontal plane exceeds 30 degrees.

Edges of slabs and breaks in floor and wall:- Under 20cm wide.

Stair cases with sloping or stepped soffits excluding landing.

Prov. Mild steel/Tor steel reinforced for RCC work including bending, binding and placing in position complete upto floor two level i/c all leads and lifts complete in all respect. :-a) Tor steel.

Half brick masonry in common burnt clay building bricks in cement mortar 1:4(1cement:4sand)second class bricks.

Prov. wood work in frames of doors, windows clerestory windows and other frames wrought framed and fixed in position:-

2nd class deodar wood.

Providing and fixing panelled glazed or panelled and glazed shutters for doors, windows and clerestory windows including black enamelled iron butt hinges with necessary screws including all leads and lifts in:-

40mm thick deodar wood 2nd class.

20mm cement plaster in single coats,on rough side of bricks/stone walls for interior plastering upto floor two level including arrises internal rounded angles, chamfers, and/or rounded angles not exceeding 80mm in girth and finished even and smooth:-a)In cement mortar 1:6 (1cement:6sand ) including all leads and lifts.

6 mm thick cement plaster in CM 1:3 (1 cement 3 sand in roof slabes

White washing with lime on undecorated wall surfaces two coats to give an even shade including thoroughly brooming the surface to remove all dirt, dust , mortar dirt and other foreign matter as per the direction of Engineer-in-charge including all leads and lifts.

Distempering two coats with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surface to give an even shade over and i/c a priming coat with distempering primer of approved brand and manufacturem after thoroughly brushing the surface free from mortor dropping and other foreign matter and also i/c preparing the surface even and sand papered smooth.Priming coat with distemper primer with in all leads and lifts complete in all respect and to the entire satisfaction of the Engineer-in-charge.

CC flooring 1:2:4, 40mm thick (with marble chips of specified shade and specified sizes)laid in floors,treads of steps and landings on a bed of 10mm average thickness of cement mortar 1:6(1 cement:6 sand ) jointing with neat cement slurry mixed with pigment to match the shade of tiles (wherever required including rubbing and polishing complete with tiles of following shade including all leads and lifts :-(a)Silver Grey.

Applying priming coat over new wood and other wood based surfaces after and including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter including all leads and lifts.

With ready made paint brushing wood primer pink.

Painting two coats (excluding priming coat) on new wood and wood based surfaces, with ready mixed paint brushing to give an even shade including cleaning of all dirt dust and other foreign matter,sand papering and stopping:-including all leads and lifts.With readymixed paint other than white.

P/F M.S. grills of required pattern in wooden frames of windows etc.with M.S.flats square or round bars with round headed bolts and nuts or by screws complete in all respect including all leads and lifts as per the direction of the Engineer-in-charge. i) Plain grills.

Stone soling properly hand packed filling interstices with spalls and consolidating with power road roller to the required gradient and camber including spreading watering and rolling of binding material moorum or earth etc. 100mm spread thickness (finished work including materials and labour) within all leads and lifts as directed by the Engineer-in-Charge.

Prov. and fixing anodized alumimium sliding door bolts anodized colour and shade bolts,nuts and screws etc. complete.

P/F aluminium Tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etc. complete.

P/F aluminium handles anodized transparent or dyed to required colour and shade with necessary screws etc. complete.

Providing Plinth protection 50mm thick in cement concrete 1:3:6(1cement:3sand:6graded stone agg. 20mm nominal size) i/c all leads and lifts and as per direction of Engineer-in-charge.

Demolition below grund level upto 1.50 metres depth including stacking of serviceable materials and disposal of unserviceable materials within 20 metres lead complete in all respect i/c all leads and lifts. a) RCC work.

Sahi Ram Malta

Sandeep Verma