PROVN OF WIRE MESH IN CERTAIN MD ACCN AND IMPROVEMENT AND STRUCTURAL REHABILITATION TO BLDG NO P-455 IN 4 AREA UNDER AGE BR-II OF GE (AF) ADM AREA AT AF STN AGRA.

Amount

Taking down cement plaster on walls/ceiling of any description including racking out joints hacking for key, scrubbing down with water etc. and removing rubbish complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the rubbies complete all as specified and directed.

Taking down existing chowkhats or frames not exc. 1.5 sqm each and removing to store or handed over to contractor from site complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description or structural steel work including doors, gates but excluding framed truss not otherwise provided complete all as specified and directed.

M&L in repairs for roof treatment with following specification including removing existing :- (i) Cleaning of existing surface properly with steel wire brushes (ii) Applying evenly a tack coat of bitumen primer @ 0.3 kg / sqm (iii) Applying a coat of hot blown bitumen 85/25 confirming to IS - 702 @ 1.2 kg / sqm (iv) Applying and laying 3 mm APP modified memberane weighting not less than 3 kg / sqm in 100 mm over laps both longitudinally and transverrsally and overlaps to be sealing by torch application , memberane shall be taken up to the thickness of slab / front fascia (v) The memberane shall be torched into groove on vertical plane and groove sealed with cement mortar 1:3 (vi) PCC Tiles 300x300x25mm laid with cement mortar 1:4 mixed with 5% integral water proofing compound by weight of cement over a 20 mm layer of cement mortar 1:4 and finished neat complete all as specified and directed (Note :- WPC shall be paid incliding in this item)

M&L for brick work with sub class 'B' bricks, old size, class designation 75, straight or curved on plan exceeding 6 mtr mean radius and built in cement mortar 1:6 including demolition of brick work or stone/ boulder masonry built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facing, dressed stone work & precast concrete articles complete all as specified and directed.

M&L for scraping out loose mortar/concrete by chiseling/ wire brushing complete and applying rust removing solution (rebaklene solution) to exposed corroded reinforcement and applying a coat of epoxy primer (Nitozink primer from M/s Fosroc or equivalent as approved by GE) as per manufacturer instructions providing and fixing of wire mesh of weight not less than 2.5 Kg per Sqm and apply screed 25 mm average thickness in CM (1:4) mixed with liquid integral water proofing compound (complast 'X' as per manufacture instructions with gunitting machine at a pressure not less than 5 Kg/Sqcm finally rendering 10mm thick plaster in CM (1:4) using liquid integral water proofing compound (complast 'X' 421 i.e. from M/s Fosroc and Nitobound AR from M/s Fosroc or equivalent as approved by GE) as per manufacture instructions complete all as specified and directed. Note :- Location such as RCC column, lintels, beams and ceiling slab etc.

Disconnecting existing tanks, setting aside (or lowering if required) for hoisting if required reconnecting and re-fixing in position complete all as specified and directed.

S & F in repairs Aluminium anodised (minimum anodisation is 50 microns) Door / window / Ventilator/partition frames and shutters (02 Nos glazed & gauzed), side hung type, without sash bars, standard aluminium grills, necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handles, locking arrangements etc., complete with standard aluminium sections, complete all as specified and as directed by Engineer-in-charge.(Aluminium section shall be of make Jindal/Hindalco/ Indalco). (Note:- Weight of various Aluminium sections handles and locking arrangements shall only be considered for measurement for payment. However cost of rubber packing given in the item shall be deemed to be included in the rate quoted. Glass panels, prelaminated particle boards, glass & aluminium wire cloth as applicable will be measured and paid separately as supplied only).

Supply only 5 mm thick sheet figured glass and glazing with rubber packing around the glass, in squares exceeding 0.50 sqm in each pane complete all as specified and as directed.

M&L for rendering 15 mm thick on internal surfaces of walls etc in cement mortar 1:6 with Pidi Proof 101 LW(+) or Dr fixit or equivalent liquid water proofing admixture @ 200 ml per bag of cement finished even and smooth without using extra cement complete all as specified and directed. (Rate of Water proofing admixture shall deemed to be included under this item).

M&L rendering 10 mm thick in CM (1:3) on ceiling surfaces finished even & smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick on external surfaces of walls etc in cement mortar 1:4 with Pidi Proof 101 LW(+) or Dr fixit or equivalent liquid water proofing admixture @ 200 ml per bag of cement finished even and smooth without using extra cement complete all as specified and directed. (Rate of Water proofing admixture shall deemed to be included under this item). Note :- The Rates are inclding Use of all scaffoldings at 12 to 14 M ht of buildings .

M&L for oil bound distempering two coats over a coat of alkali resistant priming paint including 3 mm thick wall care putty and preparation of new plastered surfaces of wall complete all as specified and directed.

M&L for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm on Newly Plastered surfacs of brick (plastered or un-plastered) or concrete surface complete all as specified and directed. Note: 1. Exterior Primer & Acrylic emulsion paint to be applied on wall surfaces with airless spray machine (Mechanical means) as approved by Engr-in-Charge & 2nd coat shall be applied after 1st coat is dry approximately 6-8 hrs between two coats.

M&L for preparation of newly plastered ceiling surfaces and applying two coats of white wash complete all as specified and directed.

M&L for Non Skid Ceramic Tiles, Coloured, of size exceeding 0.18 sqm and not exceeding 0.38 sqm, 8 mm to 10 mm thick [Square or Rectangular] as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed.

M&L for coloured glazed ceramic tiles in vertical surfaces 350X250X7mm / 450X350X 7mm thick as in skirting /dado, set and jointed in cement slurry and pointed in coloured cement to match laid over 10mm thick cement backing coat in CM 1:3 complete all as specified and as directed.

M&L for Non Skid ceramic tiles, coloured of size exceeding 0.06 Sqm and not exceeding 0.11 Sqm 7 mm to 8 mm thick [Square or Rectangular] as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons complete all as specified and directed.

M&L for Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as specified .

M&L for mirror polished machine cut kota stone slab all around marble strips of 50-100mm wide flooring 20-25 mm thick over 20 mm thick screed bed or bedding layer in cement sand screed in 1:6 base laid and jointed with grey cement slurry mixed with colouring pigment to match the colour or shade of kota stone slab including rubbing, polishing complete all as specified & directed. Note:- Size of kota stone slab not less than 550mmx550mm (cut size except the location where balanced. Marble strip shall be measured and paid seperately under respective items here in before.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with 10mm thick cement backing coat in CM 1:3 complete all as specified and as directed.

M&L for 16-18 mm thick white Marble stone machine cut, bedded jointed with grey cement laid over cement screed and jointed with 10mm thick cement backing coat in CM 1:3 and pointed with white cement including cutting and polishing in flooring around kota stone having 50 to 100 mm wide strips complet all as specified & directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. (M.S. hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made solid panel both side Pre laminated PVC door used instead of Plain colour PVC sheet. Stile and rails feathered 30mm thick (style ) shutter consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded colour plain PVC or channel having a PVC sheet strip of 20mm width stuch in side with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert top rail & bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement supplying & fixing in the frame at site as per specification & drawing complete (SSR or TD) complete all as specified and directed.

S&F Stairs (framed) including stringers, treades, landing balusters, hand rails etc. including cleats brackets Fe 290 (Gde E-165) etc complete all as specified and directed.

S&F Steel rolling shutters gear operated type with bevel gear box and crank handle as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer erected in position as indicated complete push pull or manual type complete all as specified and directed.

M&L for two coats of syntetic enamal painting over one coat of red oxide primer for new or previsouly untreated steel surfaces of any description over 10cm girth or width complete all as specified and directed.

Supply, fixing, laying & testing 15 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors and testing including taking down existing GI tubing complete all as specified and directed.

Supply, fixing, laying & testing 20 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors and testing including taking down existing GI tubing complete all as specified and directed.

S & F in repairs Two way Bib Taps, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc complete all as specified and as directed.

S&F in repairs chromium plated Health faucet (ABS Body) mild steel plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F in repairs 15mm CP Bib Taps long body fancy type heavy duty with wall flange complete all as specified and directed.

S&F in repairs( fancy type ) Anglur stop cock cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for pipe or union fixed for 15mm/20mm bore) complete all as specified and directed.

S&F in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) Squatting pan including connection to trap and to flushing pipe, anti-syphonage pipe including trap set in and including concrete and complete making good to floor complete all as specified and directed.

S&F 10 Ltrs capacity, PVC valveless, syphonic action type, low level flushing cistern, white, with inlet, ball valve, float and handle complete with all internal accessories and fixed to wall, PVC flush pipe 32 mm dia 90 cm long fixed properly to inlet of WC and making good to disturbed surfaces of wall or floor complete all as specified and directed.

S & F in repairs Vitreous china ware wash hand basin, white, flat back of size 550 mm X 400 mm including 32mm brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, etc complete all as specified and as directed.

S&F in repairs 20 mm brass chromium plateds towel rail of 20mm dia and 600mm in length 'D' shaped between flanges complete all as specified and directed.

M & L for hardcore of gauge not exceeding 63 mm of broken granite stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface including demolition cement concrete in ground floor(un reinforced ) not exc 15 cm thick (below or above ground level ) complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C1 using 20mm graded stone aggregate as in plinth protection and finished even and smooth with using extra cement complete all as specified and directed.

M&L for 100 mm thick cement concrete Type D 2 (1:4:8) (using 40 mm greaded stone aggregate ) complete all as specified and directed.

Demolition cement concrete is any description and any position not otherwise specifically for provided for reinforced ( (reinforcement cut as required to facilitate demolitionreinforced ) complete all as specified

M&L for mild steel TMT bar 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips complete all as specified and directed.

M&L for reinforced cement concrete type A-1 (1:1 1/2 :3) (using 20 mm greaded stone aggregate ) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified.

M&L for form work to sides of rough finished concrete foundations, foootings, bases of columns, raft and raft beams, sides and soffits if any of foundation and plinth beams and similar work vertical or to batter compelte all as specified and as directed by Engineer in Charge.

M&L for reinforced cement concrete type A-1 (1:1 1/2 :3) (using 20 mm greaded stone aggregate ) as in columns,pillars, piers, posts and struts etc. complete all as specified and directed.

M&L for form work to sides of Pillars, posts, struts, piers,columns and stanctions complete all as specified and directed.

M&L pre-cast RCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in cover slabs for man-holes etc set in CM (1:6) incl demolition complete all as specified and directed. Note: Steel reinforcement to be paid separately under respective item

M&L in repairs for providing and laying 60 mm thick factory made chamfered edge precast Cement Concrete paver blocks (interlocking tiles) of M-35 grade with any colour,design & pattern in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer,through vibratory compaction by using plate vibrator,filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

S&F in repair 110mm bore SWR PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors incl necessary excavation and demolition of PCC etc complete all as specified and as directed.

S & F in repair 110 mm bore PVC (SWR) bends any radius diminishing pieces or tapers with proper joints complete all as specifed and directed.

S & F in repair 110 mm bore PVC (SWR) branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specifed and directed.

Cutting holes in brick walls built in cement mortar or cement lime mortar and stone wall built in lime mortar exc. half brick but not exc. one brick for inserting holdfast and making good dismantled portion in cement mortar 1:3 or cement concrete (1:2:4) type B-1 as required complete all as specified and directed.

S&F 35 mm thk 2nd class Hard wood Kiln seasoned and chemically pressure treated glazed & skeleton shutters, open rebated at prepared to receive glass/gauze (without sash bars) edges of framing plain, chamfered, or rounded, fitted with and incl cut and mitred beads for securing glass, gauge etc, size of members of shutters as specified in SSR Pt-I, Sec-8, clause 8.24 (a) fixed to chowkhats complete all as specified and directed

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc, complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening including MS hold fast and similar article like tie bars etc. conforming to Fe-290 Gde-E-165-0 complete all as specified and directed.

M&L for PCC (1:3:6) type C-1 with using 20mm graded stone aggregate as in cill, step and for inserting hold fast of doors and windows complete all as specified and directed.

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coat of synthetic enamel paints over one coaat of pink primer complete all as specified and directed.

M&L for preparation of new steel surfaces not exc. 10 cm width or girth and applying two coat of synthetic enamel paints over one coaat of red oxide primer complete all as specified and directed.

S&F 100 mm long medium weight, cold rolled mild steel butt hinges complete all as specified and directed.

S&F aluminum anodized barrel tower bolt of extruded section size of bolt 150mm complete all as specified and directed.

S&F aluminum handle cast type anodized 150 mm size complete all as specified and directed.

S&F for 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and avg width of aperture 1.40 mm and fixed with gauging clip or strip complete all as specified and directed.

S&F mild steel ordinary rat tail rod pattern springs 300mm size including roller plate etc complete all as specified and directed.

Taking down copper/aluminium point wiring (light,fan, socket or power complete ) including fixtures and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings,calling bell etc revoing materials to store for taking credit and making good the disturbed surface of wall / ceiling /floor etc.

M&L for point wiring complete for one light/fan/ exhaust fan point controlled by one, one way 5 Amp switch with PVC (FRLSH) insulated unsheathed multistranded copper conductor of size 1.50 sqmm nominal cross sectional area single core drawn in and including minimum 20 mm dia 'medium grade' PVC concealed conduits ISI marked and fittings, including anodised pressed steel concealed terminal switch boxes not less than 1.20 mm thick of reqd size factory made duly painted inside and outside with one coat red oxide primer, 3mm thick plastic laminated bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers complete including 1.50 sqmm nominal cross sectional area PVC(FRLSH) insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories including cutting chases for concealed piping and making good disturbed surface to match the existing surface complete all as specified and directed.

All as per srl item No 68 above but for 3 pin socket outlet 5 amps socket on independent board

All as per srl item No 68 above but for 3 pin socket outlet 5 amps socket on same board

All as per srl item No 68 above but for 3 pin socket outlet 15 amps socket on independent board but 2.5 sqmm cable and 2.5 sqmm cable as earth continuity conductor.

S&F Switch piano, flush type, single pole, one way 5/6 Amp 230 Volts complete all as specified and directed.

S&F Switch piano, flush type, single pole, one way 15/16 Amp 230 Volts complete all as specified and directed.

S&F socket outlet, flush type, single pole, 2 in 1, 5 pin 5/6 Amp, 230 volts complete all as specified and directed.

S&F socket outlet, flush type, single pole, multipurpose 2 in 1, 6 pin 15/16 Amp, 230 volts complete all as specified and directed.

S&F ceiling fan regulator, electronic, socket type, 5 speed 230 volts suitable for 1200/1400 mm sweep ceiling fan including necessary connection complete all as specified and directed.

S&F ceiling rose 3 Ph PVC / Polycarbonate isolated body complete all as specified and directed.

S&F tube light fitting with energy saving decorative batten type 10 watt energy efficient tube light fitting (2 Feet) highly durable surface mounted LED batten constructed of fire retardent engineering grade extruded plastic and decorative end caps with all accessories prewired and making connection with 3 core copper flexible cable of size 23/.0076 from ceilling rose/PVC connector to light fittings complete all as specified and directed. Make- ORIENT Cat part No-LBLN-10-C-SQ or Phlips cat part- BN021LED12S6500PSUGR or Havells Cat part No- LUMILINE+ BS10WLED865SPCSS

S&F tube light fitting with energy saving decorative batten type 10 watt energy efficient tube light fitting (2 Feet) highly durable surface mounted LED batten constructed of fire retardent engineering grade extruded plastic and decorative end caps with all accessories prewired and making connection with 3 core copper flexible cable of size 23/.0076 from ceilling rose/PVC connector to light fittings complete all as specified and directed. Make- ORIENT Cat part No-LBLN-10-C-SQ/Phlips cat part- BN021LED12S6500PSUGR, Havells Cat part No- LUMILINE+ BS10WLED865SPCSS

S&F tube light fitting with energy saving decorative batten type 10 watt energy efficient tube light fitting (2 Feet) highly durable surface mounted LED batten constructed of fire retardent engineering grade extruded plastic and decorative end caps with all accessories prewired and making connection with 3 core copper flexible cable of size 23/.0076 from ceilling rose/PVC connector to light fittings complete all as specified and directed. Make- ORIENT Cat part No-LBLN-10-C-SQ or Phlips cat part- BN021LED12S6500PSUGR or Havells Cat part No- LUMILINE+ BS10WLED865SPCSS

S&F for energy effiecient 5 star rating, ceiling fan 1200mm sweep with remote operated suitable to work on single phase AC, 26/28 W 230 volts 50Hz complete with connecting electrically to ceiling rose or connector black using PVC insulated and over all sheathed 3 core cable of size 0.75 Sqmm with flexible copper conductor complete all as specified and directed.

S&F exhaust fan 300mm sweep single phase 230 volts 50Hz AC supply totally enclosed with die cast aluminium rotor mounted on two ball bearings complete with louvers including cutting chases for fixing fan connecting electrically using 3 core 0.75 Sqmm PVC insulated flexible copper conductor cable over all sheathed complete all as specified and directed.

S & F in repair sheet metal enclosure distribution board double door with suitable size busbar TPN 4 way verticle type as per IEC- 61439-3., With Neutral bar, earthbar and cable ties for cable management complete all as specified and directed.

S & F in repair sheet metal enclosure distribution board double door with 100 Amps copper bus bar SPN 4 way IP -54, IK-19, as per IEC- 61439-3., With Neutral bar, earthbar and cable ties for cable management complete all as specified and directed.

Supply and fixing MCCB 100 Amp four pole 415V, 16 KA complete all as specified and directed.

S&F amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN 5 to 32 AMP poles and current carrying capacity in the MCB DB complete all as specified and directed.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB complete all as specified and directed.

M&L for earthing complete with galvanised steel plate electrode 600mm x 600mm x 6mm thick buried directly in ground (earth pit not less than 2.25 Mts deep below ground level with top edge of the plate not less than 1.50 Mtrs below ground level connected to glavanised iron Wire 4.0 mm dia by means of bolts, nuts check nuts and washers of galvanised iron or steel connected to earthing test point all as specified incl 15 mm GI tubing medium grade and necessary fitting for protection of GI wire incl laying of charcoal dust and common salt in alternate layer, PCC Pit (1:3:6) type C-1 using 20 mm graded stone aggregate, RCC cover 40mm thick (1:2:4) type B-0 using 12.5 mm graded stone aggregate reinforced with 6 mm dia round bar @ 75 mm C/C both ways with MS handle 8 mm dia, plastering 15 mm thick CM (1:6) externally upto 150mm below ground level , GI funnel with 20mm dia medium grade GI pipe for watering and wire mesh incl excavation and earth work and disposal of surplus soil complete all as specified and shown on electrical plate No 3 of SSR Part (2009) and connected to earth test point incl testing and marking Bldg Nos and writing Test Results on a 3.0 mm thick painted M.S. earth pit marking Plate (200mm x 100mm) duly welded with a 450 mm long 10 mm dia round M.S. rod, fixed with the earth pit chamber by grouting complete including taking out old unserviceable earthing system including demolishing old earth pit chambers and removing of debris from the site with levelling the ground all as specified an directed.

S&F in repair sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 6 sqmm nominal cross sectional area and one run of 6 sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including not less than 20 mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings including cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification complete all as specified and directed.

Supply and fixing post top lantern 30/35 Watts, 230 volts, 50 Hz with IP65 protection, mushroom or oval shaped in opal/ prismatic finish made out of polycarbonate, suitable all accessories and prewired complete all as specified and directed.

S&F street light fittings with LED street light fitting 36 Watts with dusk dawn sensor ,automatic switch on and switch off operation based on ambient lux lavels, ,having cast alumn housing, polycarbonate diffuser , secondary optical lance, IP 65, including making connections complete all as specified and directed. Make: Orent Cat Ref LSFT 036C -DLS or equivalent to Phillips / Wipro / Havells/ Shakti

S&F GI bracket made out of GI pipe 40 mm bore medium grade bent to required shape of 0.90 mtr long and fixing to pole/wall with suitable size of nut, bolts and clamps complete all as specified and directed.

Supply and fix to wall, roof new steel water tubing of size 25 mm bore, galvanized medium grade including all complete fitting such as bends, elbows, tees unions, sockets etc laid complete in above ground all as specified of size 25 mm dia

Supply and fix gun metal gate valve of size 25 mm bore with iron wheel head comforming to IS-778 class -I screwed both ends for iron pipes complete all as specified and directed.

Cutting existing steel tubing for alterations or additions of size 25 mm bore complete all as specified and directed.

Taking down existing meter keeping safe custody and refixing after complete the work including fixing in wall complete all as specified and directed.

Captainkomalchaharconstructions (BID ID -3120902)

rohan traders (BID ID -3121747)

M/S SINGH ELECTRIC CO (BID ID -3133104)

M/s Pooran Singh and Company (BID ID -3120536)

garg construction company (BID ID -3133088)

saroj constructions (BID ID -3124252)