Loading…
Loading…
Tender Value
₹2.2 Cr
EMD Value
₹2.6 L
Closing Date
10 Mar 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
WORK 3
14 conditions · 3 needing a document upload
As a proof of sufficient financial capacity:- The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-D, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The tenderer must have successfully completed as defined in 1.1 during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: Three similar works costing not less than the amount equal to 30% of advertised value of the tender, or Two similar works costing not less than the amount equal to 40% of advertised value of the tender, or One similar work costing not less than the amount equal to 60% of advertised value of the tender. (Credential from private individuals for whom such works are executed/being executed should not be accepted).{Authentic copy of the documents should be uploaded by the tenderer(s) along with their offer to fulfill the eligibility criteria otherwise their offers will not be considered and summarily rejected}.
Building/structure or Bridge work or Supply of building materials
48 conditions · 6 needing a document upload
(A) The stamp duty payable in Bank Guarantee for Bid Security and Performance guarantee differs from state/Union of Territory to state/Union of Territory as per the provisions of stamp Duty Act applicable in that particular state/Union of Territory on the date of execution of Bank Guarantee. The value of Non-Judicial Stamp paper for execution of the BG to be submitted shall be higher of the following two values:- (a) Stamp value as applicable in state/Union Territory from where Stamp paper is purchased. (b) Stamp value as applicable in the state of Uttar Pradesh. Stamp Duty applicable in the state of Uttar Pradesh for submission of Bank Guarantee for Bid Security and Performance Guarantee is Rs. Five per thousand or part thereof, subjected to maximum value of Rs. Ten Thousand (Rs. 10,000/-). (B) Bid offer of tenderer who submits Bank Guarantee in lieu of Bid security in violation of Para (A) above will be summarily rejected.
Audited Balance Sheet duly certified by the Chartered Accountant regarding contractual payments received in the past.
Please submit your bank details i.e.Name of the Bank along with Bank Branch Code, Account Number, IFSC Code, and PAN Number.
Please furnish list of plant and Machinery available on hand own and proposed to be inducted own and hired to be given separately for the subject work.
Please furnish list of Works on hand indicating Description of Work, Contract Value, Approximate value of balance work yet to be done and Date of award.
Certificates and testimonials regarding contracting experience for the type of job for which tender is invited with list of works carried out in the past giving Description of Work, Organization for whom executed, approximate value of contract at time of award, Date of award and Date of Completion. Date of actual Start, Actual Completion and Final value of Contract shall also be given.
Please furnish list of personal, organization available on hand and proposed to be engaged for the subject work.
At the time of submission of bid, if you have any special Condition then upload in scanned pdf copy.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
POA :- Regarding Power of Attorney, the conditions as per General Manager/Law/Gorakhpur's letter No. C/78/LO/Misc/HO/2024 dated 05.08.2024 attached herewith shall be applicable.
The earnest money deposited with the tender of successful tenderer will be retained as part of security deposit which will be 5 percent of the value of work awarded. The balance amount of security deposit will recovered on account bills of the work @ 6 percent till it reaches upto 5 percent of the value including earnest money.
For enactment of this Act, the tenderer shall be required to pay cess 1 of cost of construction work to be deducted from each bill. Cost of material shall be outside the purview of cess, when supplied under a separate schedule item Railway Boards No. 2008/ CE-1 CT/6 Dt. 09-07-2008
Rates are inclusive of all taxes/octroi, license fee, royalty charges etc. legally leviable by State, Central Govt. and/or any other local authority.
For those conditions for which standard formats have been given in the uploaded document titled-Formats for uploading of various format. The informations should only be submitted in these standard formats.
In addition to General condition of contract 2022 and Indian Railways Unified standard specification Works Materials Volume I II 2010, revised upto date, special condition attached shall also apply.
Sales tax/Business tax will be recovered as per extant instruction on the subject.
The successful tenderer will have to submit full security deposit as per GCC-2022 before execution of the agreement.
a) The successful bidder shall have to submit a Performance Guarantee (PG) within 21 (Twenty one) days from the date of issue of Letter of Acceptance (LOA). Extension of time for submission of PG beyond 21 (Twenty one) days and upto 60 days from the date of issue of LOA may be given by the Authority who is competent to sign the contract agreement. However, a penal interest of 12% per annum shall be charged for the delay beyond 21(Twenty one) days, i.e. from 22nd day after the date of issue of LOA. Further, if the 60th day happens to be a declared holiday in the concerned office of the Railway, submission of PG can be accepted on the next working day. In all other cases, if the Contractor fails to submit the requisite PG even after 60 days from the date of issue of LOA, the contract is liable to be terminated. In case contract is terminated railway shall be entitled to forfeit Earnest Money Deposit and other dues payable against that contract. In case a tenderer has not submitted Earnest Money Deposit on the strength of their registration as a Startup recognized by Department of Industrial Policy and Promotion (DIPP) under Ministry of Commerce and Industry, DIPP shall be informed to this effect. The failed Contractor shall be debarred from participating in re-tender for that work.
b) The successful bidder shall submit the Performance Guarantee PG in any of the following forms, amounting to 5 percent of the contract value: i A deposit of Cash ii Irrevocable Bank Guarantee iii Government Securities including State Loan Bonds at 5 percent below the market value i v Deposit Receipts, Pay Orders, Demand Drafts and Guarantee Bonds. These forms of Performance Guarantee could be either of the State Bank of India or of any of the Nationalized Banks v Guarantee Bonds executed or Deposits Receipts tendered by all Scheduled Banks v i A Deposit in the Post Office Saving Bank vii A Deposit in the National Savings Certificates viii Twelve years National Defence Certificates ix Ten years Defence Deposits x National Defence Bonds and xi Unit Trust Certificates at 5 percent below market value or at the face value whichever is less. Also, FDR in favour of FA & CAO/N. E. Railway free from any encumbrance may be accepted.
(1)Price Variation Clause (PVC) shall be applicable only in tender having advertised value above Rs.2 Crores. Provided further that, in a contract where PVC is applicable, following shall be outside the purview of price adjustments (i.e. shall be excluded from the gross value of the work for the purpose of price variation) : (a) Materials supplied by Railway to the Contractors, either free or at fixed rate; (b) Any extra item(s) included in subsequent variation falling outside the purview of the Bill(s) of Quantities of tender, under clause 39. (1)(b) of these Standard General Conditions, unless applicability of PVC and 'Base Month' has been specially agreed, while fixing the rates of such extra item(s).(2) Price Variation Clause for Annual Maintenance Contract or Zonal Contract :- The price variation Clause of General Conditions of Contract shall not apply to a works contract which is either an Annual Maintenance Contract or a Zonal Contract as per Railway Boards letter No. 2013/CE/I/CT/O/10-PVC-Pt.I dated 27.01.2015 & 2017/Trans/01/Policy dated 08.02.2018.(3) Price Variation Clause shall be applicable accordingly attached document.
Bank Guarantees BGs to be submitted by suppliers/contractors should be sent directly to the Divisional Railway Manager/Engineering, N.E. Railway, Ashok Marg, Lucknow- 226001 by issuing Bank under registered Post A.D.
1- The B.G. Bonds submitted by contractors/bidders should be issued via SFMS. 2- The online verification of such B.G. Bonds is carried out through the AIMS portal. 3- No B.G. Bond is accepted unless it is verifiable through the SFMS system.
(1) Earnest Money Cost: -All the tenderers/Contractors have to deposit full earnest money as stipulated in the tender document through online modes as permitted in IREPS application. (2) Tender Document Cost: -All the tenderers/Contractors have to deposit tender document cost as stipulated in the tender document through online modes as permitted in IREPS application.
a- One qualified Graduate Engineer where the cost of the work to be executed is Rs.200 lakh and above. b- One qualified Diploma Holder Engineer where the cost of the work to be executed is more then Rs.25 lakh, but less then Rs.200 lakh. Technical staff should be available at site whenever required by the Engineer-in-charge to take instructions. In case the contractor fails to employ the qualified Engineer, he shall be liable to pay amount of Rs.40000 and Rs.25000 for each month or part thereof for the default period for the provisions, as contained in para a and b above respectively. The decision of the Engineer-incharge as to the period for which the required technical staff was not employed by the contractor and as to the reasonableness of the amount to be deducted on this account shall be final and binding on the contractor.
Care in Submission of Tenders :
Before submitting a tender, the tenderer will be deemed to have satisfied himself by actual inspection of the site and locality of the works, that all conditions liable to be encountered during the execution of the works are taken into account and the rates he enters in the tender forms are adequate and all inclusive to accord with the provisions in Clause-37 of the Standard General Conditions of Contract for the completion of works to the entire satisfaction of the Engineer.
Tenderers will examine the various provisions of the Central Goods and Services Tax Act, 2017(CGST)/Integrated Goods and Services Tax Act, 2017(IGST)/Union Territory Goods and Services Tax Act, 2017(UTGST)/respective states State Goods and Services Tax Act (SGST) also, as notified by Central/State Govt. and as amended from time to time and applicable taxes before bidding. Tenderers will ensure that full benefit of Input Tax Credit (ITC) likely to be availed by them is duly considered while quoting rates.
The successful tenderer who is liable to be registered under CGST/IGST/ UTGST/SGST/ Act shall submit GSTIN along with other details required under CGST/IGST/UTGST/SGST Act to railway immediately after the award of contract, without which no payment shall be released to the contractor. The contractor shall be responsible for deposition of applicable GST to the concerned authority.
In case the successful tenderer is not liable to be registered under CGST/IGST/UTGST/SGST Act, the railway shall deduct the applicable GST from his/their bills under reverse charge mechanism (RCM) and deposit the same to the concerned authority.
All documents related to Constitution of Firm by the Partnership Firm/ Joint venture/ Society/Companies/ MOU etc. duly notorized should be uploaded at the time of submission of bid.
The tenderer shall upload scanned copies of mandatory credentials such as experience certificates (Except Private Individual), turn over Certificates and any other documents as applicable.
Goods & Service Tax (GST) will be recovered as per extant instruction on the subject.
NER-LJN-Division:- Provision of electronic interlocking under remodeling work at LJN yard.
NER-LJN-2026-30
NER-LJN-2026-30
Open
Works - General
12 Months
Lucknow, Uttar Pradesh
₹0
₹2.6 L
10 Mar 2026
10 Feb 2026
80 items across 1 schedule · ₹2,02,10,070.13 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | All kinds of soil. | cum | 1100.88 | 286.85 | 3,15,787.43 |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. | cum | 303.24 | 253.95 | 77,007.8 |
| 3 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 53.02 | 6,833.4 | 3,62,306.87 |
| 4 | 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) | cum | 32.15 | 6,326.05 | 2,03,382.51 |
| 5 | 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 83.16 | 8,364.2 | 6,95,566.87 |
| 6 | 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 115 | 10,185.05 | 11,71,280.75 |
| 7 | cum | 87 | 10,719.3 | 9,32,579.1 | |
| 8 | Foundations, footings, bases of columns, etc. for mass concrete | Sqm | 390.61 | 307.95 | 1,20,288.35 |
| 9 | Suspended floors, roofs, landings, balconies and access platform | Sqm | 465.1 | 766.55 | 3,56,522.41 |
| 10 | Lintels, beams, plinth beams, girders, bressumers and cantilevers | Sqm | 312.84 | 608.35 | 1,90,316.21 |
| 11 | Columns, Pillars, Piers, Abutments, Posts and Struts | Sqm | 365.47 | 804.25 | 2,93,929.25 |
| 12 | Thermo-Mechanically Treated bars of grade Fe-500D or more. | Kg | 46079.62 | 89.65 | 41,31,037.93 |
| 13 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 379 | 6,658.25 | 25,23,476.75 |
| 14 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 487 | 8,288.35 | 40,36,426.45 |
| 15 | Cement mortar 1:4 (1 cement :4 coarse sand) | Sqm | 90 | 1,018.05 | 91,624.5 |
| 16 | Area of slab over 0.50 sqm | Sqm | 14.4 | 4,425.35 | 63,725.04 |
| 17 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. | Sqm | 108 | 1,063.45 | 1,14,852.6 |
| 18 | Decorative plywood both side decorative veneer (Type - I) conforming to IS 1328 BWR type | Sqm | 58.32 | 2,366.35 | 1,38,005.53 |
| 19 | 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | Sqm | 12.96 | 3,086.1 | 39,995.86 |
| 20 | Fixed to steel windows by welding | Kg | 450 | 181 | 81,450 |
| 21 | 125x65x2.12 mm | Each | 43 | 48 | 2,064 |
| 22 | 100x58x1.90 mm | Each | 194 | 39.05 | 7,575.7 |
| 23 | 50x40x2.50 mm | Each | 43 | 21.8 | 937.4 |
| 24 | 250x10 mm | Each | 14 | 74.65 | 1,045.1 |
| 25 | 200x10 mm | Each | 7 | 61.05 | 427.35 |
| 26 | 125 mm | Each | 29 | 35.2 | 1,020.8 |
| 27 | Single rubber stopper | Each | 22 | 35.5 | 781 |
| 28 | Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete. | Each | 11 | 739.8 | 8,137.8 |
| 29 | Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. | Metre | 8.1 | 702.6 | 5,691.06 |
| 30 | 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge. | Sqm | 2.14 | 3,963.7 | 8,482.32 |
| 31 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | Kg | 3500 | 111.95 | 3,91,825 |
| 32 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). | Kg | 540 | 612.25 | 3,30,615 |
| 33 | Stainless steel (grade 304) wire gauge of 0.5 mm dia wire and 1.4 mm aperture on both sides | Sqm | 29.16 | 971.55 | 28,330.4 |
| 34 | Light shade pigment using white cement | Sqm | 36 | 1,295.2 | 46,627.2 |
| 35 | Acid and alkali resistant tile | Sqm | 93.6 | 1,515.45 | 1,41,846.12 |
| 36 | Size of Tile 600x600 mm | Sqm | 360 | 1,416.65 | 5,09,994 |
| 37 | 75 mm diameter | Metre | 54 | 213 | 11,502 |
| 38 | 75 mm | Each | 11 | 79.8 | 877.8 |
| 39 | 75 mm | Each | 11 | 79.8 | 877.8 |
| 40 | 75 mm bend | Each | 11 | 91.8 | 1,009.8 |
| 41 | 75 mm | Each | 27 | 310.85 | 8,392.95 |
| 42 | 1:6 (1 cement: 6 fine sand) | Sqm | 1626.75 | 282 | 4,58,743.5 |
| 43 | New work (two or more coats) over and including water thinnable priming coat with cement primer | Sqm | 575.26 | 162.55 | 93,508.51 |
| 44 | Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture | Sqm | 270 | 191.4 | 51,678 |
| 45 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. | Sqm | 1626.75 | 123.85 | 2,01,472.99 |
| 46 | Two coats | Sqm | 1051.49 | 116.05 | 1,22,025.41 |
| 47 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. | cum | 12 | 219.35 | 2,632.2 |
| 48 | Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres. | Sqm | 500 | 180.5 | 90,250 |
| 49 | Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density). | cum | 250 | 20.55 | 5,137.5 |
| 50 | 53 mm to 22.4 mm size stone aggregate | cum | 125 | 1,837.25 | 2,29,656.25 |
| 51 | Stone screening 11.2 mm nominal size (Type B) | cum | 75 | 2,065.7 | 1,54,927.5 |
| 52 | Moorum | cum | 75 | 888.3 | 66,622.5 |
| 53 | Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density . | cum | 75 | 865.8 | 64,935 |
| 54 | On W.B.M. @ 0.75 Kg / sqm | Sqm | 500 | 45.2 | 22,600 |
| 55 | On bituminous surface @ 0.50 Kg / sqm | Sqm | 500 | 36.6 | 18,300 |
| 56 | With paving Asphalt grade VG - 10 heated and then mixed with solvent at the rate of 70 grams per kg of asphalt | Sqm | 500 | 227 | 1,13,500 |
| 57 | Providing and laying seal coat of premixed fine aggregate ( passing 2.36 mm and retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade VG - 10 bitumen per cum of fine aggregate and 0.60 cum of fine aggregate per 100 sqm of road surface, including rolling and finishing with road roller all complete. | Sqm | 500 | 79.85 | 39,925 |
| 58 | Cement concrete prepared with batch mixing machine | cum | 53 | 9,492.9 | 5,03,123.7 |
| 59 | White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests | Each | 2 | 5,781.35 | 11,562.7 |
| 60 | W.C. pan with ISI marked white solid plastic seat and lid | Each | 2 | 5,540.55 | 11,081.1 |
| 61 | One urinal basin with 5 litre white P.V.C. automatic flushing cistern | Each | 2 | 5,268.85 | 10,537.7 |
| 62 | White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps | Each | 2 | 2,040.85 | 4,081.7 |
| 63 | 32 mm dia | Each | 4 | 90.95 | 363.8 |
| 64 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. | Each | 4 | 1,411.15 | 5,644.6 |
| 65 | C.P. brass | Each | 4 | 680.8 | 2,723.2 |
| 66 | 15 mm nominal dia Pipes | Metre | 36 | 255.9 | 9,212.4 |
| 67 | 20 mm nominal dia Pipes | Metre | 54 | 325.1 | 17,555.4 |
| 68 | 25 mm nominal dia Pipes | Metre | 180 | 408.55 | 73,539 |
| 69 | 15 mm nominal bore | Each | 9 | 303.85 | 2,734.65 |
| 70 | 20 mm nominal bore | Each | 9 | 327.95 | 2,951.55 |
| 71 | 20 mm nominal bore | Each | 4 | 327.95 | 1,311.8 |
| 72 | 20 mm nominal bore | Each | 4 | 397.45 | 1,589.8 |
| 73 | With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 | Each | 2 | 1,712.15 | 3,424.3 |
| 74 | With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 | Each | 2 | 10,102.5 | 20,205 |
| 75 | 125 mm nominal dia with 25 mm waste hole | Each | 7 | 45.25 | 316.75 |
| 76 | Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) | Kg | 216 | 433.95 | 93,733.2 |
| 77 | Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) | Kg | 54 | 573.4 | 30,963.6 |
| 78 | With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) | Sqm | 58.32 | 1,325.55 | 77,306.08 |
| 79 | With stainless steel cover plate minimum 1.25 mm thickness | Each | 11 | 2,448.85 | 26,937.35 |
| 80 | Cement mortar 1:3 (1 cement : 3 coarse sand) | cum | 8.1 | 14,275.75 | 1,15,633.58 |
| Schedule total | ₹2,02,10,070.13 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Supplyofrainforcedsteelsplcondition2025.pdf
InstructionstoTenderers52025.pdf
POAGuidelines.pdf
GeneralConditions09.09.2025_1.pdf
TrackCondition.pdf
GCC-2022-updateduptoACS10.pdf
SFMSPolicyBGverificationviaSFMS.pdf
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .