PROVISION OF FACILITY BUILDINGS FOR PROGRAME SAMOOHA AT DSP, HYDRABAD

Amount

SCH 'A' PART-I TO XVI: Note: These schedules are pre-priced by MES and the rate indicated against the respective schedule under Col 6 signifies this fact only. The tenderer is required to quote their lumpsum amount under col 13 against item of works catered under these schedule .

Lumpsum price inserted under col 13 by the tenderer for BUILDING & STRUCTURE as listed in Schedule ‘A’ Part I representing the percentege arrived under col 54 above/below the lumpsum estimated rate inserted under col 6 by the MES in Schedule ‘A’ Part I

Lumpsum price inserted under col 13 by the tenderer for SITE CLEARANCE AND DEVELOPMENT INCLUDING DEMOLITION as listed in Schedule ‘A’ Part II representing the percentege arrived under col 54 above/below the lumpsum estimated rate inserted under col 6 by the MES in Schedule ‘A’ Part II

Lumpsum price inserted under col 13 by the tenderer for Internal Water Supply as listed in Schedule ‘A’ Part III representing the percentege arrived under col 54 above/below the lumpsum estimated rate inserted under col 6 by the MES in Schedule ‘A’ Part III

Lumpsum price inserted under col 13 by the tenderer for Internal Electric Supply as listed in Schedule ‘A’ Part IV representing the percentege arrived under col 54 above/below the lumpsum estimated rate inserted under col 6 by the MES in Schedule ‘A’ Part IV

Lumpsum price inserted under col 13 by the tenderer for Road/Path/Culvert as listed in Schedule ‘A’ Part V representing the percentege arrived under col 54 above/below the lumpsum estimated rate inserted under col 6 by the MES in Schedule ‘A’ Part V

Lumpsum price inserted under col 13 by the tenderer for Sewage Disposal as listed in Schedule ‘A’ Part VI representing the percentege arrived under col 54 above/below the lumpsum estimated rate inserted under col 6 by the MES in Schedule ‘A’ Part VI

Lumpsum price inserted under col 13 by the tenderer for Area Drainage as listed in Schedule ‘A’ Part VII representing the percentege arrived under col 54 above/below the lumpsum estimated rate inserted under col 6 by the MES in Schedule ‘A’ Part-VII

Lumpsum price inserted under col 13 by the tenderer for External Water Supply as listed in Schedule ‘A’ Part VIII representing the percentege arrived under col 54 above/below the lumpsum estimated rate inserted under col 6 by the MES in Schedule ‘A’ Part-VIII

Lumpsum price inserted under col 13 by the tenderer for External Electrification as listed in Schedule ‘A’ Part IX representing the percentege arrived under col 54 above/below the lumpsum estimated rate inserted under col 6 by the MES in Schedule ‘A’ Part-IX

Lumpsum price inserted under col 13 by the tenderer for Area Lighting as listed in Schedule ‘A’ Part X representing the percentege arrived under col 54 above/below the lumpsum estimated rate inserted under col 6 by the MES in Schedule ‘A’ Part-X

Lumpsum price inserted under col 13 by the tenderer for Lightening Conductor as listed in Schedule ‘A’ Part XI representing the percentege arrived under col 54 above/below the lumpsum estimated rate inserted under col 6 by the MES in Schedule ‘A’ Part-XI

Lumpsum price inserted under col 13 by the tenderer for Fire Fighting system as listed in Schedule ‘A’ Part XII representing the percentege arrived under col 54 above/below the lumpsum estimated rate inserted under col 6 by the MES in Schedule ‘A’ Part-XII

Lumpsum price inserted under col 13 by the tenderer for Fire Alarm System as listed in Schedule ‘A’ Part XIII representing the percentege arrived under col 54 above/below the lumpsum estimated rate inserted under col 6 by the MES in Schedule ‘A’ Part-XIII

Lumpsum price inserted under col 13 by the tenderer for Telephone / LAN Conduits as listed in Schedule ‘A’ Part XIV representing the percentege arrived under col 54 above/below the lumpsum estimated rate inserted under col 6 by the MES in Schedule ‘A’ Part-XIV

Lumpsum price inserted under col 13 by the tenderer for UPS Wiring as listed in Schedule ‘A’ Part XV representing the percentege arrived under col 54 above/below the lumpsum estimated rate inserted under col 6 by the MES in Schedule ‘A’ Part XV

Lumpsum price inserted under col 13 by the tenderer for Special Earthing as listed in Schedule ‘A’ Part XVI representing the percentege arrived under col 54 above/below the lumpsum estimated rate inserted under col 6 by the MES in Schedule ‘A’ Part-XVI

SCHEDULE 'A' PART-XVII (MISCELLANEOUS B/R AND E/M Items) Note: This schedule is not pre-priced by MES and the rate indicated as "Rs 0.00" under Col 6 signifies this fact only.The tenderer is required to quote their rate under col 13 against item of works catered under this schedule .

SITE CLEARANCE AND DEVELOPMENT INCLUDING DEMOLITION

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

Banking excavated earth in layers not exc 20cm in depth, breaking clods,watering , rolling each layerwith 1/2 tonne roller, or wooden or steel rammers, and rolling every 3 rd and top most layer with power roller of 8 tonnes and dressing up , in embankments etc lead up to 50m and lead up to 1.50 m in all kind of soil complete all as directed.

M&L for Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with Cement mortar 1:6 (1 cement : 6 coarse sand)

INTERNAL WATER SUPPLY

M&L, Angular Stop Cock With Wall Flange all as specified andas directed by engineer in charge.

M&L, 2 Way Bib Cock With Wall Flange complete all as specified and directed.

M&L swan neck Pillar Cock With Lift Type Operating Knob & Base Flange complete all as specified and directed.

M&L Hand Shower (Health Faucet) with 8mm Dia, 1.2 Meter Long Flexible Tube & Wall Hook complete all as specified and directed.

M&L, auto closing concealed urinal flush valve all as specified andas directed by engineer in charge.

M&L Towel Ring Round with Round Flange - Chrome complete all as specified and directed.

Providing and fixing Push Button Soap Dispenser capacity: 0.8L material: ABS finish: white/smoked of approved quality & make and as per the direction of Engineer-in-charge.

INTERNAL ELECTRIFICATION

S&F LED Highbay 120W powder coated light fitting suitable for suspension mounting at any height in Hangers/Workshop with aluminum alloy pressure die cast housing and control gear box with high efficiency long life LEDs with lumen output not less than 15000lm, CCT 5700 K or above with specified beam angle to ensure better uniformity of light distribution, IP65 Protection and impact resistance of IK07, built in electronic driver, lower THD, open circuit protection, over surge and voltage protection complete with all accessories complete all as specified.

S&F LED Highbay 60W powder coated light fitting suitable for suspension mounting at any height in Hangers/Workshop with aluminum alloy pressure die cast housing and control gear box with high efficiency long life LEDs with lumen output not less than 15000lm, CCT 5700 K or above with specified beam angle to ensure better uniformity of light distribution, IP65 Protection and impact resistance of IK07, built in electronic driver, lower THD, open circuit protection, over surge and voltage protection complete with all accessories complete all as specified.

S&F Recess mounted 20W LED down lighter suitable for Armstrong/Grid ceiling with pressure die-cast aluminium heat sink, PC diffuser in white powder coated finish with integrated driver and high performance LEDs complete with all accessories complete all as specified.

S&F Surface mounted 12W LED down lighter suitable for Surface ceiling with pressure die-cast aluminium heat sink, PC diffuser in white powder coated finish with integrated driver and high performance LEDs complete with all accessories complete all as specified.

S&F LED tube light fitting. 20 W, 230v .regal batten type,Double side connection included with 20 watt LED tube rod single side connection complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete..

S&F basic all purpose surface or wall mounted 9W LED batten with polycarbonate housing and integratedelectronic driver complete all as specified.

S&F LED light fitting 2 X 2 ft 36 Watt , 230v uniquely clean & simple lighting system offering continuous, uniform lines of light across ceilings, the aluminium extruded suspended light gives continuous lines of light distribution with the possibility of various shapes complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable joint kit/mounting kit and mains cable size complete.

S&F sheet metal enclosure for pre wired distribution board double door, powder coated VTPN 6 way with out MCCB, three phase 415 volt with 200 Amps rated tinned electrolytic copper bus bar with neutral link complete.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required

Supplying and fixing Wall mounting air circulators 400mm sweep, 230V Complete all as specified and directed

Supply, Install, testing and commissioning, factory made and tested, CPRI approved LT panel board indoor type, weather, dust and vermin proof, free standing floor mounting type mounted on floor, separate cable alley for all the feeders, suitable for 440Volts, 3 Phase 4wire 50Hz AC supply system, conforming to IS, IP-54 class protection and made of 2 mm CRCA mild steel sheet & angle iron frame, compartmentalized with rubber gasket hinged doors, front & rear opening and locking arrangement (including provision of 65mm Godrej (freedom) lock with 2 keys) with necessary bus bar arrangement with electrolytic grade aluminium bus bar 500Amps rating for phase and neutral 4 strips with colour coded PVC sleeves, installed on epoxy insulators housed in separate bus chambers covered with heat shrinkable sleeves with necessary bus bar tapings for MCCBs, copper control wiring of required size for instruments and duly powder coated on the outside and inside including air ventilation for heat dissipation, suitable size knock out holes for cable glands, cable gland and lugs for incoming and outgoing cable etc., independent multilayer chambers to accommodate complete all as specified and directed including the following accessories :- (MISSION Bldg Panel)

a) Aluminium Bus bar suitable capacity TPN, full for phase and neutral with colour code PVC sleeves. - 01 Job b) LED RYB indicating lamps – 01 set c) LED Ammeter and voltmeter witn necessary CTs and display of required rating d) Adjustable thermal and magnetic release MCCB 400 Amps, 4 POLE,36 KA, 415 Volts - 01 Nos (Incoming) e) MCCB 63 Amps, 4 POLE,18 KA, 415 Volts - 04 Nos (Out going) f) MCCB 32 Amps, 4 POLE,18 KA, 415 Volts - 11 Nos (Out going)( g) Panel wiring with PVC Insulated un sheathed single core, 1100 Volts grade cable with copper conductor, multi stranded of suitable size. - 01 Job h) Interconnection of busbar with MCCB, , contactor with suitable size aluminium bus bar - 01 Job i) Provisioning of cable glands and cable lugs for all incoming and out going cables & connecting the earthing to an earthing test point to main switch board as specified and testing on completion complete all as specified & directed by Engr-in-Charge. - 1 Job

Supply, Install, testing and commissioning, factory made and tested, CPRI approved LT panel board indoor type, weather, dust and vermin proof, free standing floor mounting type mounted on floor, separate cable alley for all the feeders, suitable for 440Volts, 3 Phase 4wire 50Hz AC supply system, conforming to IS, IP-54 class protection and made of 2 mm CRCA mild steel sheet & angle iron frame, compartmentalized with rubber gasket hinged doors, front & rear opening and locking arrangement (including provision of 65mm Godrej (freedom) lock with 2 keys) with necessary bus bar arrangement with electrolytic grade aluminium bus bar 500Amps rating for phase and neutral 4 strips with colour coded PVC sleeves, installed on epoxy insulators housed in separate bus chambers covered with heat shrinkable sleeves with necessary bus bar tapings for MCCBs, copper control wiring of required size for instruments and duly powder coated on the outside and inside including air ventilation for heat dissipation, suitable size knock out holes for cable glands, cable gland and lugs for incoming and outgoing cable etc., independent multilayer chambers to accommodate complete all as specified and directed including the following accessories :- (MISSION Bldg Panel)

a) Aluminium Bus bar suitable capacity TPN, full for phase and neutral with colour code PVC sleeves. - 01 Job b) LED RYB indicating lamps – 01 set c) LED Ammeter and voltmeter witn necessary CTs and display of required rating d) Adjustable thermal and magnetic release MCCB 400 Amps, 4 POLE,36 KA, 415 Volts - 01 Nos (Incoming) e) MCCB 63 Amps, 4 POLE,18 KA, 415 Volts - 05 Nos (Out going) f) MCCB 32 Amps, 4 POLE,18 KA, 415 Volts - 02 Nos (Out going) g) Panel wiring with PVC Insulated un sheathed single core, 1100 Volts grade cable with copper conductor, multi stranded of suitable size. - 01 Job h) Interconnection of busbar with MCCB, contactor with suitable size aluminium bus bar - 01 Job i) Provisioning of cable glands and cable lugs for all incoming and out going cables & connecting the earthing to an earthing test point to main switch board as specified and testing on completion complete all as specified & directed by Engr-in-Charge. - 1 Job j) Provisioning of cable glands and cable lugs for all incoming and out going cables & connecting the earthing to an earthing test point to main switch board as specified and testing on completion complete all as specified & directed by Engr-in-Charge. - 1 Job

Supply, Install, testing and commissioning, factory made and tested, CPRI approved LT panel board indoor type, weather, dust and vermin proof, free standing floor mounting type mounted on floor, separate cable alley for all the feeders, suitable for 440Volts, 3 Phase 4wire 50Hz AC supply system, conforming to IS, IP-54 class protection and made of 2 mm CRCA mild steel sheet & angle iron frame, compartmentalized with rubber gasket hinged doors, front & rear opening and locking arrangement (including provision of 65mm Godrej (freedom) lock with 2 keys) with necessary bus bar arrangement with electrolytic grade aluminium bus bar 200Amps rating for phase and neutral 4 strips with colour coded PVC sleeves, installed on epoxy insulators housed in separate bus chambers covered with heat shrinkable sleeves with necessary bus bar tapings for MCCBs, copper control wiring of required size for instruments and duly powder coated on the outside and inside including air ventilation for heat dissipation, suitable size knock out holes for cable glands, cable gland and lugs for incoming and outgoing cable etc., independent multilayer chambers to accommodate complete all as specified and directed including the following accessories :- (MISSION &AIT Bldg Panel)

a) Aluminium Bus bar suitable capacity TPN, full for phase and neutral with colour code PVC sleeves. - 01 Job b) LED RYB indicating lamps – 01 set c) LED Ammeter and voltmeter witn necessary CTs and display of required rating d) Adjustable thermal and magnetic release MCCB 160 Amps, 4 POLE,25 KA, 415 Volts - 01 Nos (Incoming) f) MCCB 32 Amps, 4 POLE,18 KA, 415 Volts - 05 Nos (Out going) g) Panel wiring with PVC Insulated un sheathed single core, 1100 Volts grade cable with copper conductor, multi stranded of suitable size. - 01 Job h) Interconnection of busbar with MCCB, , contactor with suitable size aluminium bus bar - 01 Job i) Provisioning of cable glands and cable lugs for all incoming and out going cables & connecting the earthing to an earthing test point to main switch board as specified and testing on completion complete all as specified & directed by Engr-in-Charge. - 1 Job j) Provisioning of cable glands and cable lugs for all incoming and out going cables & connecting the earthing to an earthing test point to main switch board as specified and testing on completion complete all as specified & directed by Engr-in-Charge. - 1 Job

Supply, Install, testing and commissioning, factory made and tested, CPRI approved LT panel board indoor type, weather, dust and vermin proof, free standing floor mounting type mounted on floor, separate cable alley for all the feeders, suitable for 440Volts, 3 Phase 4wire 50Hz AC supply system, conforming to IS, IP-54 class protection and made of 2 mm CRCA mild steel sheet & angle iron frame, compartmentalized with rubber gasket hinged doors, front & rear opening and locking arrangement (including provision of 65mm Godrej (freedom) lock with 2 keys) with necessary bus bar arrangement with electrolytic grade aluminium bus bar 500Amps rating for phase and neutral 4 strips with colour coded PVC sleeves, installed on epoxy insulators housed in separate bus chambers covered with heat shrinkable sleeves with necessary bus bar tapings for MCCBs, copper control wiring of required size for instruments and duly powder coated on the outside and inside including air ventilation for heat dissipation, suitable size knock out holes for cable glands, cable gland and lugs for incoming and outgoing cable etc., independent multilayer chambers to accommodate complete all as specified and directed including the following accessories :- (MISSION Bldg Panel)

a) Aluminium Bus bar suitable capacity TPN, full for phase and neutral with colour code PVC sleeves. - 01 Job b) LED RYB indicating lamps – 01 set c) LED Ammeter and voltmeter witn necessary CTs and display of required rating d) Adjustable thermal and magnetic release MCCB 400 Amps, 4 POLE,36 KA, 415 Volts - 01 Nos (Incoming) e) MCCB 63 Amps, 4 POLE,18 KA, 415 Volts - 02 Nos (Out going) f) MCCB 32 Amps, 4 POLE,18 KA, 415 Volts - 08 Nos (Out going) g) Panel wiring with PVC Insulated un sheathed single core, 1100 Volts grade cable with copper conductor, multi stranded of suitable size. - 01 Job h) Interconnection of busbar with MCCB, , contactor with suitable size aluminium bus bar - 01 Job i) Provisioning of cable glands and cable lugs for all incoming and out going cables & connecting the earthing to an earthing test point to main switch board as specified and testing on completion complete all as specified & directed by Engr-in-Charge. - 1 Job j) Provisioning of cable glands and cable lugs for all incoming and out going cables & connecting the earthing to an earthing test point to main switch board as specified and testing on completion complete all as specified & directed by Engr-in-Charge. - 1 Job

Supply, Install, testing and commissioning, factory made and tested, CPRI approved LT panel board indoor type, weather, dust and vermin proof, free standing floor mounting type mounted on floor, separate cable alley for all the feeders, suitable for 440Volts, 3 Phase 4wire 50Hz AC supply system, conforming to IS, IP-54 class protection and made of 2 mm CRCA mild steel sheet & angle iron frame, compartmentalized with rubber gasket hinged doors, front & rear opening and locking arrangement (including provision of 65mm Godrej (freedom) lock with 2 keys) with necessary bus bar arrangement with electrolytic grade aluminium bus bar 250Amps rating for phase and neutral 4 strips with colour coded PVC sleeves, installed on epoxy insulators housed in separate bus chambers covered with heat shrinkable sleeves with necessary bus bar tapings for MCCBs, copper control wiring of required size for instruments and duly powder coated on the outside and inside including air ventilation for heat dissipation, suitable size knock out holes for cable glands, cable gland and lugs for incoming and outgoing cable etc., independent multilayer chambers to accommodate complete all as specified and directed including the following accessories :- (MISSION &AIT Bldg Panel)

a) Aluminium Bus bar suitable capacity TPN, full for phase and neutral with colour code PVC sleeves. - 01 Job b) LED RYB indicating lamps – 01 set c) LED Ammeter and voltmeter witn necessary CTs and display of required rating d) Adjustable thermal and magnetic release MCCB 200 Amps, 4 POLE, 25 KA, 415 Volts - 01 Nos (Incoming) f) MCCB 32 Amps, 4 POLE,18 KA, 415 Volts - 06 Nos (Out going) g) Panel wiring with PVC Insulated un sheathed single core, 1100 Volts grade cable with copper conductor, multi stranded of suitable size. - 01 Job h) Interconnection of busbar with MCCB, contactor with suitable size aluminium bus bar - 01 Job i) Provisioning of cable glands and cable lugs for all incoming and out going cables & connecting the earthing to an earthing test point to main switch board as specified and testing on completion complete all as specified & directed by Engr-in-Charge. - 1 Job j) Provisioning of cable glands and cable lugs for all incoming and out going cables & connecting the earthing to an earthing test point to main switch board as specified and testing on completion complete all as specified & directed by Engr-in-Charge. - 1 Job

S&F, Flame proof Junction box, 3 phase, isolated body complete all as specified and directed.

S&F, recess mounting LED with white fixture, IP 65 dust free & zero maintenance LED clean room bottom opening luminaire for clean room power consumption 80W or less system lumens output 4200 or above, CCT ≥5700, suitable for Armstrong / Grid ceiling with high brightness SMD LEDs complete with all accessories including driver pre-wired complete all as specified.

S&F, recess mounting LED with white fixture, IP 65 dust free & zero maintenance LED clean room bottom opening luminaire for clean room power consumption 36W or less system lumens output 4200 or above, CCT ≥5700, suitable for Armstrong / Grid ceiling with high brightness SMD LEDs complete with all accessories including driver pre-wired complete all as specified.

S&F, Flame proof SS sheet metal enclosure with metal clad plug and socket three phase with five pin and earth plug & socket suitable for flush mounting 415 V, 32 Amps capacity controlled by and including one 32 Amps MCB TPN, C series, 10 KA capacity complete all as specified and directed.

S&F, Flame proof SS sheet metal enclosure with metal clad plug and socket three phase with five pin and earth plug & socket suitable for flush mounting 415 V, 63 Amps capacity controlled by and including one 63 Amps MCB TPN, C series, 10 KA capacity complete all as specified and directed.

ROAD / PATH / CULVERT Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm

Providing and laying semi-dense Bituminous concrete 40mm compacted thickness with bitumen of grade VG-30 @ 5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engr-in-Charge.

Providing and applying 2.5 mm thick road marking strips (retroreflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications

Providing and laying factory made chamfered edge Cement Concrete paver blocks 80mm thick of M-35 grade with approved colour, design & pattern in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. .

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round 450 mm diameter NP-2 class RCC pipes including bed concrete as per standard design

SEWAGE DISPOSAL Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round NP-2 class RCC pipes including bed concrete as per standard design :150 mm diameter NP-2 class RCC pipe

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design

(a.) Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

(b.) Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Add to above item No. 39.01 & 39.02 for Extra for depth for manholes

(a.) Size 120x90 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

(b.) Size 90x80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

AREA DRAINAGE Extra for forming fair finished to drain or channel 45cm to 90cm inner girth in cement concrete using extra cement including forms, moulds etc

Returning Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and for all lift.

Providing and fixing in position rectangular shape precast RCC manhole / drain cover of size 600mm x 450mm Light Duty with miniumume 25KN load bearing capacity.

EXTERNAL WATER SUPPLY M&L, Construction of Brick Masonry valve chamber of size 900 x 900 x 1000 mm (Internal dimensions) with PCC 1:4:8 foundation 150mm thick, brick work built in CM 1:6, PCC 1:3:6 coping 50mm thick, plastering 15mm thick in CM 1:6 to all internal and exposed surfaces including excavation earthwork in hard/dense soil, MS sheet cover 4mm thick with locking arrangement embedded in PCC and painting to MS cover with two coats of synthetic enamel paint over one coat of red oxide primer etc complete all as specified and directed.

EXTERNAL ELECTRIFICATION Supply, Install, testing and commissioning, factory made and Type tested, approved LT panel board indoor type, weather, dust and vermin proof, free standing floor mounting type mounted on floor, separate cable alley for all the feeders, suitable for 440Volts, 3 Phase 4wire 50Hz AC supply system, conforming to IS, IP-54 class protection and made of 2 mm CRCA mild steel sheet & angle iron frame, compartmentalized with rubber gasket hinged doors, front & rear opening and locking arrangement (including provision of 65mm Godrej (freedom) lock with 2 keys) with necessary bus bar arrangement with electrolytic grade aluminium bus bar 4000Amps rating for phase and neutral 4 strips with colour coded PVC sleeves, installed on epoxy insulators housed in separate bus chambers covered with heat shrinkable sleeves with necessary bus bar tapings for MCCBs, copper control wiring of required size for instruments and duly powder coated on the outside and inside including air ventilation for heat dissipation, suitable size knock out holes for cable glands, cable gland and lugs for incoming and outgoing cable etc., independent multilayer chambers to accommodate complete all as specified and directed including the following accessories :- (Mission bldg MAIN Panel)

a) Aluminium Bus bar TPN OF RATING 4000 A, full for phase and neutral with colour code PVC sleeves. - 01 Job b) LED RYB indicating lamps – 01 set c) LED multifunction meter and energy meter witn necessary CTs and display of required rating . d) MP BasedACB 3200 Amps, EDO,4 POLE, 75 KA ,415 Volts - 01Nos (Incomer) e) MP Based ACB 2500 Amps, EDO, 4 POLE, 60 KA, 415 Volts - 02Nos (Outgoing)(01 for Industrial Socket and 01 for spare) f) Adjustable thermal and magnetic release MCCB 320 Amps, 4 POLE, 50 KA, 415 Volts - 01Nos (Outgoing)(for DG SET) g) MCCB 630 Amps, 4 POLE,36 KA, 415 Volts - 01 Nos make L&T with Cat NoCM94106OOS1OG or equivalent make (Out going)(For AC Plant) h) MCB 32 Amps, 4 POLE, 415 Volts - 01 Nos (Out going)(For Substation ) i) Panel wiring with PVC Insulated un sheathed single core, 1100 Volts grade cable with copper conductor, multi stranded of suitable size. - 01 Job j) Interconnection of busbar with MCCB, , contactor with suitable size aluminium bus bar - 01 Job k) Provisioning of cable glands, spreader links and cable lugs for all incoming and out going cables & connecting the earthing to an earthing test point to main switch board as specified and testing on completion complete all as specified & directed by Engr-in-Charge. - 1 Job

Supply, Install, testing and commissioning, factory made and Type tested, approved LT panel board outdoor type, weather, dust and vermin proof, free standing floor mounting type mounted on floor, separate cable alley for all the feeders, suitable for 440Volts, 3 Phase 4wire 50Hz AC supply system, conforming to IS, IP-54 class protection and made of 3mm CRCA mild steel sheet & angle iron frame, compartmentalized with rubber gasket hinged doors, front & rear opening and locking arrangement (including provision of 65mm Godrej (freedom) lock with 2 keys) with necessary bus bar arrangement with electrolytic grade aluminium bus bar 3000Amps rating for phase and neutral 4 strips with colour coded PVC sleeves, installed on epoxy insulators housed in separate bus chambers covered with heat shrinkable sleeves with necessary bus bar tapings for MCCBs, copper control wiring of required size for instruments and duly powder coated on the outside and inside including air ventilation for heat dissipation, suitable size knock out holes for cable glands, cable gland and lugs for incoming and outgoing cable etc., independent multilayer chambers to accommodate complete all as specified and directed including the following accessories :- (Mission Bldg Industrial socket panel).

a) Aluminium Bus bar suitable capacity TPN, full for phase and neutral with colour code PVC sleeves. - 01 Job b) LED RYB indicating lamps – 01 set c) LED multifunction meter and energy meter witn necessary CTs and display of required rating . d) MP Based ACB 2500 Amps, 4 POLE, 75 KA, 415 Volts - 01Nos (Incoming) e) MP Based MCCB 400 Amps, 4 POLE,36 KA, 415 Volts - 8 Nos (Out going)(07 for GF, and 01 for spare) e) MP Based MCCB 160 Amps, 4 POLE,25 KA, 415 Volts - 1 Nos (Out going)(01 for SF) f) Panel wiring with PVC Insulated un sheathed single core, 1100 Volts grade cable with copper conductor, multi stranded of suitable size. - 01 Job g) Interconnection of busbar with MCCB, , contactor with suitable size aluminium bus bar - 01 Job h) Provisioning of cable glands and cable lugs for all incoming and out going cables & connecting the earthing to an earthing test point to main switch board as specified and testing on completion complete all as specified & directed by Engr-in-Charge. - 1 Job

Supply, Install, testing and commissioning, factory made and Type tested, approved LT panel board indoor type, weather, dust and vermin proof, free standing floor mounting type mounted on floor, separate cable alley for all the feeders, suitable for 440Volts, 3 Phase 4wire 50Hz AC supply system, conforming to IS, IP-54 class protection and made of 2 mm CRCA mild steel sheet & angle iron frame, compartmentalized with rubber gasket hinged doors, front & rear opening and locking arrangement (including provision of 65mm Godrej (freedom) lock with 2 keys) with necessary bus bar arrangement with electrolytic grade aluminium bus bar 400Amps rating for phase and neutral 4 strips with colour coded PVC sleeves, installed on epoxy insulators housed in separate bus chambers covered with heat shrinkable sleeves with necessary bus bar tapings for MCCBs, copper control wiring of required size for instruments and duly powder coated on the outside and inside including air ventilation for heat dissipation, suitable size knock out holes for cable glands, cable gland and lugs for incoming and outgoing cable etc., independent multilayer chambers to accommodate complete all as specified and directed including the following accessories :- (MISSION Bldg DG set Panel)

a) Aluminium Bus bar suitable capacity TPN, full for phase and neutral with colour code PVC sleeves. - 01 Job b) LED RYB indicating lamps – 01 set c) LED multifunction meter and energy meter witn necessary CTs and display of required rating . d) MP Based MCCB 320 Amps, 4 POLE,36 KA, 415 Volts - 01 Nos (Incoming) e) MP Based MCCB 200 Amps, 4 POLE,36 KA, 415 Volts - 02 Nos (Out going)(01 For GF and 01 For Spare) f) MCCB 100 Amps, 4 POLE,25 KA, 415 Volts - 02 Nos (Out going)(for F/F &SF) i) MCB 32 Amps, 4 POLE, 415 Volts - 02 Nos (Out going)(for Security and street lighting) j) Panel wiring with PVC Insulated un sheathed single core, 1100 Volts grade cable with copper conductor, multi stranded of suitable size. - 01 Job k) Interconnection of busbar with MCCB, , contactor with suitable size aluminium bus bar - 01 Job l) Provisioning of cable glands and cable lugs for all incoming and out going cables & connecting the earthing to an earthing test point to main switch board as specified and testing on completion complete all as specified & directed by Engr-in-Charge. - 1 Job

Supply, Install, testing and commissioning, factory made and Type tested, approved LT panel board indoor type, weather, dust and vermin proof, free standing floor mounting type mounted on floor, separate cable alley for all the feeders, suitable for 440Volts, 3 Phase 4wire 50Hz AC supply system, conforming to IS, IP-54 class protection and made of 2 mm CRCA mild steel sheet & angle iron frame, compartmentalized with rubber gasket hinged doors, front & rear opening and locking arrangement (including provision of 65mm Godrej (freedom) lock with 2 keys) with necessary bus bar arrangement with electrolytic grade aluminium bus bar 250Amps rating for phase and neutral 4 strips with colour coded PVC sleeves, installed on epoxy insulators housed in separate bus chambers covered with heat shrinkable sleeves with necessary bus bar tapings for MCCBs, copper control wiring of required size for instruments and duly powder coated on the outside and inside including air ventilation for heat dissipation, suitable size knock out holes for cable glands, cable gland and lugs for incoming and outgoing cable etc., independent multilayer chambers to accommodate complete all as specified and directed including the following accessories :- (AIT Bldg DG Set Panel)

a) Aluminium Bus bar suitable capacity TPN, full for phase and neutral with colour code PVC sleeves. - 01 Job b) LED RYB indicating lamps – 01 set c) LED multifunction meter and energy meter witn necessary CTs and display of required rating . d) MP Based MCCB 200 Amps, 4 POLE,36 KA, 415 Volts - 01 Nos (Incoming) e) MP Based MCCB 160 Amps, 4 POLE,36 KA, 415 Volts - 02 Nos (Out going)(01 For GF and 01 For Spare) f) MCCB 32 Amps, 4 POLE, 25 KA, 415 Volts - 02 Nos (Out going)(for F/F &SF) g) MCB 32 Amps, 4 POLE, 415 Volts - 02 Nos (Out going)(for Security and street lighting)) h) Panel wiring with PVC Insulated un sheathed single core, 1100 Volts grade cable with copper conductor, multi stranded of suitable size. - 01 Job i) Interconnection of busbar with MCCB, , contactor with suitable size aluminium bus bar - 01 Job j) Provisioning of cable glands and cable lugs for all incoming and out going cables & connecting the earthing to an earthing test point to main switch board as specified and testing on completion complete all as specified & directed by Engr-in-Charge. - 1 Job

Supply, Install, testing and commissioning, factory made and Type tested, approved LT panel board indoor type, weather, dust and vermin proof, free standing floor mounting type mounted on floor, separate cable alley for all the feeders, suitable for 440Volts, 3 Phase 4wire 50Hz AC supply system, conforming to IS, IP-54 class protection and made of 2 mm CRCA mild steel sheet & angle iron frame, compartmentalized with rubber gasket hinged doors, front & rear opening and locking arrangement (including provision of 65mm Godrej (freedom) lock with 2 keys) with necessary bus bar arrangement with electrolytic grade aluminium bus bar 2000Amps rating for phase and neutral 4 strips with colour coded PVC sleeves, installed on epoxy insulators housed in separate bus chambers covered with heat shrinkable sleeves with necessary bus bar tapings for MCCBs, copper control wiring of required size for instruments and duly powder coated on the outside and inside including air ventilation for heat dissipation, suitable size knock out holes for cable glands, cable gland and lugs for incoming and outgoing cable etc., independent multilayer chambers to accommodate complete all as specified and directed including the following accessories :- (AIT Main panel)

a) Aluminium Bus bar suitable capacity TPN, full for phase and neutral with colour code PVC sleeves. - 01 Job b) LED RYB indicating lamps – 01 set c) LED multifunction meter and energy meter witn necessary CTs and display of required rating . d) MP Based ACB 1600 Amps, EDO 4 POLE, 50 KA ,415 Volts - 01Nos (Incomer) e) MP Based ACB 800 Amps,EDO 4 POLE, 50 KA, 415 Volts - 03Nos (Outgoing)(01 for Industrial socket ,01 for AC Plant and 01 for spare) f) MP Based MCCB 320 Amps, 4 POLE,36 KA, 415 Volts - 01 No (Out going)(for fire fighting ) f) MP Based MCCB 200 Amps, 4 POLE,36 KA, 415 Volts - 01 No (Out going)(for DG Set) g) MCB 32 Amps, 4 POLE, 415 Volts - 01 Nos (Out going)(spare) h) Panel wiring with PVC Insulated un sheathed single core, 1100 Volts grade cable with copper conductor, multi stranded of suitable size. - 01 Job i) Interconnection of busbar with MCCB, , contactor with suitable size aluminium bus bar - 01 Job j) Provisioning of cable glands and cable lugs for all incoming and out going cables & connecting the earthing to an earthing test point to main switch board as specified and testing on completion complete all as specified & directed by Engr-in-Charge. - 1 Job

Supply, Install, testing and commissioning, factory made and Type tested, approved LT panel board outdoor type, weather, dust and vermin proof, free standing floor mounting type mounted on floor, separate cable alley for all the feeders, suitable for 440Volts, 3 Phase 4wire 50Hz AC supply system, conforming to IS, IP-54 class protection and made of 3mm CRCA mild steel sheet & angle iron frame, compartmentalized with rubber gasket hinged doors, front & rear opening and locking arrangement (including provision of 65mm Godrej (freedom) lock with 2 keys) with necessary bus bar arrangement with electrolytic grade aluminium bus bar 1000Amps rating for phase and neutral 4 strips with colour coded PVC sleeves, installed on epoxy insulators housed in separate bus chambers covered with heat shrinkable sleeves with necessary bus bar tapings for MCCBs, copper control wiring of required size for instruments and duly powder coated on the outside and inside including air ventilation for heat dissipation, suitable size knock out holes for cable glands, cable gland and lugs for incoming and outgoing cable etc., independent multilayer chambers to accommodate complete all as specified and directed including the following accessories :-(AIT bldg Industrial socket panel)

a) Aluminium Bus bar suitable capacity TPN, full for phase and neutral with colour code PVC sleeves. - 01 Job b) LED RYB indicating lamps – 01 set c) LED multifunction meter and energy meter witn necessary CTs and display of required rating . d) MP Based ACB 800 Amps, EDO 4 POLE, 50 KA ,415 Volts - 01Nos (Incomer) e) MP Based MCCB 400 Amps, 4 POLE,36 KA, 415 Volts - 02 Nos (Out going) f) MP Based MCCB 200 Amps, 4 POLE,36 KA, 415 Volts - 02 Nos (Out going) g) MCB 32 Amps, 4 POLE, 415 Volts - 01 Nos (Out going)(spare) i) Panel wiring with PVC Insulated un sheathed single core, 1100 Volts grade cable with copper conductor, multi stranded of suitable size. - 01 Job j) Interconnection of busbar with MCCB, , contactor with suitable size aluminium strip - 01 Job k) Provisioning of cable glands and cable lugs for all incoming and out going cables & connecting the earthing to an earthing test point to main switch board as specified and testing on completion complete all as specified & directed by Engr-in-Charge. - 1 Job

Supplying, testing and commissioning 1100 volts grade, LT XLPE insulated, PVC sheathed as per IS-7098 (Part-I), 1988 galvanized steel strip or wire armoured, heavy duty, electric cables, with multistranded aluminium conductor laid in trenches/ passing through pipe/duct/road crossing or fixed on poles, walls with suitable size clamps made out of mild steel flat iron including jointing material such as crimping type lugs, brass cable glands, heavy duty double compression type, complete all as specified and directed of following sizes

(a)630 sqmm 1 core

Supply, installation, Testing and commissioning of double wound copper transformer step down, outdoor type complete with standard fittings, primary voltage of HT 11000 Volts and secondary LT 433 volts, 3 Phase 4 wire with frequency 50 c/s. Provided with 7 No of off load tappings on HT side to vary secondary voltage within range of +5% to - 10% (in steps of 2.5%), star delta connections with vector group of Dyn 11, Impedance of 4.5% and including first filling of transformer oil as per IS:335 and colour coating with one coat of primer and two coats of BS grey colour. Losses all as per IS:1180 (Level - ii) of capacity of 1000 KVA with all standerd accessiories required proper functioning of Transformer including the following :

Supply, installation, Testing and commissioning of double wound copper transformer step down, outdoor type complete with standard fittings, primary voltage of HT 11000 Volts and secondary LT 433 volts, 3 Phase 4 wire with frequency 50 c/s. Provided with 7 No of off load tappings on HT side to vary secondary voltage within range of +5% to - 10% (in steps of 2.5%), star delta connections with vector group of Dyn 11, Impedance of 4.5% and including first filling of transformer oil as per IS:335 and colour coating with one coat of primer and two coats of BS grey colour. Losses all as per IS:1180 (Level - ii) of capacity of 2000 KVA with all standerd accessiories required proper functioning of Transformer including the following :

Supply, installation connecting electrically commissioning and testing complete outdoor type, as recommended by manufacturer, Automatic Power Factor Correction(APFC) system 6 stage type intel VAr APFC Panel with heavy duty MPPH capacitors and MCCBs 500 Amps 35 KA as incomer factory made single unit 440 volts, 50 Hz, 3 phase 250 KVAR (4No X 50 KVAR + 2 No x 25 KVAR) comprising with following provisions :-

(h) Bus bar of appropiate rating for incoming and out going connection suitable to withstand short circuit current of 50 KA and current rating not less than 1.5 time of load current made of copper mounted on SMC silicon free, Chlorine freepost insulators,and arranged in such a way that the joints are minimum. (j) Emergency stop push button to disconnect the unit in case of emergency. (k) Indicator LED type for phase indication and capacitor banks ON and OFF Indication.

(I) Current transformer 01 No of appropriate rating , to be fixed in incoming existing LT panel for operation of APFC relay complete with control wiring. Note:- All accessories prewired with suitable size copper conductor cable insulated with fibre glass insulation to with stand high temperature , housed in cubical panel(CPRI approved) made out of 1.6 mm thick MS sheet factory made duly powder coated front and rear door open able with locking arrangement complete with foundation as required or recommended by manufacturer.

Supply, installation connecting electrically commissioning and testing complete outdoor type, as recommended by manufacturer, Automatic Power Factor Correction(APFC) system 8 stage type intel VAr APFC Panel with heavy duty MPPH capacitors and ACB 800 Amps 50 KA as incomer factory made single unit 440 volts, 50 Hz, 3 phase 450 KVAR (2 No X 100 KVAR + 4 No x 50 KVAR + 2 No x 25 KVAR) comprising with following provisions :--

(h) Bus bar of appropiate rating for incoming and out going connection suitable to withstand short circuit current of 50 KA and current rating not less than 1.5 time of load current made of copper mounted on SMC silicon free, Chlorine freepost insulators,and arranged in such a way that the joints are minimum. (j) Emergency stop push button to disconnect the unit in case of emergency. (k) Indicator LED type for phase indication and capacitor banks ON and OFF Indication.

(I) (I) Current transformer 01 No of appropriate rating , to be fixed in incoming existing LT panel for operation of APFC relay complete with control wiring. Note:- All accessories prewired with suitable size copper conductor cable insulated with fibre glass insulation to with stand high temperature , housed in cubical panel(CPRI approved) made out of 1.6 mm thick MS sheet factory made duly powder coated front and rear door open able with locking arrangement complete with foundation as required or recommended by manufacturer.

S&F, following elements/components of Compact Low Tension all Aluminium Bus Duct 1600A, 433V Sandwich type 3 Phase +100% Neutral, duly enclosed in sheet steel enclosure made of hot galvanised sheet steel, minimum 1.5mm thick, epoxy powder coated with high resistance to chemical agents, rigid and robust, compact and corrosion less; Bus Duct enclosure shall be designed for very high mechanical, electrical and heat loss efficiency; Enclosure shall be with IP-65 protection for both indoors and outdoors suitable for power distribution; single/multiple bolted monoblock junction contact assembly made with splice plates (fish plates) shall be used for installing successive feeders/ elbows/ flanges etc.; provided with Aluminium protective earth strip/flat of 50% cross sectional area of phase conductor, internally/ externally through out the length of enclosure and shall be effectively connected to the enclosure by riveting/bolting or any suitable means for specified earth continuity; provided with GI canopy not less than 2mm thick for outdoor stretches complete all as per NEC : SP-30 : 2011, IS-8623, IEC-61439-6, IEC-60364-5-54, IEC-529 & latest relevant standards, all as specified and directed.

S&F, following elements/components of Compact Low Tension all Aluminium Bus Duct 3200A, 433V Sandwich type 3 Phase +100% Neutral, duly enclosed in sheet steel enclosure made of hot galvanised sheet steel, minimum 1.5mm thick, epoxy powder coated with high resistance to chemical agents, rigid and robust, compact and corrosion less; Bus Duct enclosure shall be designed for very high mechanical, electrical and heat loss efficiency; Enclosure shall be with IP-65 protection for both indoors and outdoors suitable for power distribution; single/multiple bolted monoblock junction contact assembly made with splice plates (fish plates) shall be used for installing successive feeders/ elbows/ flanges etc.; provided with Aluminium protective earth strip/flat of 50% cross sectional area of phase conductor, internally/ externally through out the length of enclosure and shall be effectively connected to the enclosure by riveting/bolting or any suitable means for specified earth continuity; provided with GI canopy not less than 2mm thick for outdoor stretches complete all as per NEC : SP-30 : 2011, IS-8623, IEC-61439-6, IEC-60364-5-54, IEC-529 & latest relevant standards, all as specified and directed.

Supplying and installing 300mm x 50mm x 1.6mm thick size of perforated painted with powder coating M.S. Cable trays bends with perforation not more than 17.5% joined with connectors,suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required complete all as specified and directed.

Supplying, Laying, testing and commissioning 11KV volts grade, 240 Sqmm 3 core HT XLPE insulated, PVC sheathed as per IS-7098 (Part-II), 2011 galvanized steel strip or wire armoured, heavy duty, electric cables, with multistranded aluminium conductor laid in trenches/ passing through pipe/duct/road crossing or fixed on poles, walls with suitable size clamps made out of mild steel flat iron including jointing material such as crimping type lugs, brass cable glands, heavy duty double compression type, complete all as specified and directed.

Supply installation, testing & commissioning of the following siwtch gears set having 01 Nos of 11 KV, 3-Phase, 50 HZ, 800 Amps, 350 MVA, 26.3 KA Vacuum Circuit Breakers, extensible indoor type with motorized and manual spring charging facility breaking capacity 26.3 KA for 3 Seconds, SCADA compatible, having pad lock, provision for earth switch complete with all necessary accessories and standard fittings (e.g. Relays, C.T.s, P.T.s, Power pack, spring charging motor, trip coil, ammeter, voltmeter, indication lamps etc) all as specified, required at and as directed, comprising of 01 Nos of outgoing VCB and 01 bus coupler connecting the VCBs with existing VCB at MRS. Each VCB comprising the following: - Note: Rate quoted by contractor deemed to include any addn/ alt to exciting tapping outgoing panel from MRS/TSTF SS

(a) 11 KV, 3 Phase, 50 HZ, 800 Amps, 26.3 KA, VCB having short circuit current withstand capacity not less than 26.3 KA for 3 Seconds, having manual and automatic charging mechanism, by DC / Universal motor suitable for 110 Volts / 230 Volts AC / DC or as per OEM's recommendations, shunt trip coil, indication lamp, on off switch padlock, provision for earth switch etc complete all as specified and directed. (b) Double Core and Double Ratio type dry type current transformers (C.Ts) of ratio 5-25/5-5 Amps, suitable for 11 KV, 3 Phase, 50 HZ, having 15 VA burden or as per OEM's recommendation with 0.5 class accuracy for metering and % P10 accuracy for protection-01 Set of three. (c) Dry type 11 KV/110 Volts potential transformer (P.T.s) suitable for 11 KV, 3 Phase, 50 HZ, connected to bus bar class-1 accuracy of 100 VA burden or as per OEM's recommendation complete all as specified and directed-01 Set.

(d) Electronic type solid state programmable type self powered, SCADA compatible having overload, earth fault and short circuit tripping facility with memory to record fault event with fault current and type of fault with real date and time suitable for 11 KV, 3 Phase, 50 HZ VCB and having high torque, less burden not more than 3 VA and low overshoot suitable for 5 of 1 Amps current rating and having three over current and one earth fault elements with over current range not less than 50% to 200% in steps of not less than 5% with time multiplier setting range not less than 0.1 to 1.0 in steps of not more than 0.01 (separate for over current and earth fault) suitable DC auxiliary supply and housed on horizontal draw out type case flush pattern with accessories duly connected with trip and alarm system complete all as specified and directed-01 Set. (e) LED type indication lamps for circuit breaker open (OFF)-'GREEN', Circuit breaker close (ON) 'RED' Circuit breaker trip 'YELLOW', Spring charge 'BLUE' trip circuit healthy with push button and R-Y-B phase indication lamp complete all as specified - 01 Set.

(j) Power pack of suitable capacity contained in maintenance free batteries and battery charger to provide auxiliary power supply to VCB all as per OEM's recommendation and as directed at site by Engineer-in-Charge. (k) Internal control and metering wiring with PVC insulated copper conductor cables of suitable cross sections, necessary power connections and civil work as required for installation of cable. (l) Any other standard accessories required for smooth operation of VCB or recommended by OEM.

Supply installation, testing & commissioning of 11 KV, 3 Phase, 50 HZ of the following capacities of Vacuum Circuit Breaker, extensible indoor type with motorized and manual spring charging facility breaking capacity 26.3 KA for 3 Seconds, SCADA compatible, having pad lock, provision for earth switch complete with all necessary accessories and standard fittings (e.g. Relays, Digital C.T.s, P.T.s, power pack, spring charging motor, trip coil, ammeter, voltmeter, indication lamps etc) with online temperature monitoring system all as specified, required at site and as directed, comprising of following . (i) 01 No of VCBs 11 KV, 3 Phase, 50 Hz, 800 Amps (as incomer) (ii) 02 No of VCBs 11 KV, 3 Phase, 50 Hz, 400 Amps (as out going)

(a) 11 KV, 3 Phase, 50 HZ, 800 Amps, 26.3 KA, VCB having short circuit current withstand capacity not less than 26.3 KA for 3 Seconds, having manual and automatic charging mechanism, by DC / Universal motor suitable for 110 Volts / 230 Volts AC / DC or as per OEM's recommendations, shunt trip coil, indication lamp, on off switch padlock, provision for earth switch etc complete all as specified and directed. (b) Double Core and Double Ratio type dry type current transformers (C.Ts) of ratio 5-25/5-5 Amps, suitable for 11 KV, 3 Phase, 50 HZ, having 15 VA burden or as per OEM's recommendation with 0.5 class accuracy for metering and % P10 accuracy for protection-01 Set of three. (c) Dry type 11 KV/110 Volts potential transformer (P.T.s) suitable for 11 KV, 3 Phase, 50 HZ, connected to bus bar class-1 accuracy of 100 VA burden or as per OEM's recommendation complete all as specified and directed-01 Set.

(d) Electronic type solid state programmable type self powered, SCADA compatible having overload, earth fault and short circuit tripping facility with memory to record fault event with fault current and type of fault with real date and time suitable for 11 KV, 3 Phase, 50 HZ VCB and having high torque, less burden not more than 3 VA and low overshoot suitable for 5 of 1 Amps current rating and having three over current and one earth fault elements with over current range not less than 50% to 200% in steps of not less than 5% with time multiplier setting range not less than 0.1 to 1.0 in steps of not more than 0.01 (separate for over current and earth fault) suitable DC auxiliary supply and housed on horizontal draw out type case flush pattern with accessories duly connected with trip and alarm system complete all as specified and directed-01 Set. (e) LED type indication lamps for circuit breaker open (OFF)-'GREEN', Circuit breaker close (ON) 'RED' Circuit breaker trip 'YELLOW', Spring charge 'BLUE' trip circuit healthy with push button and R-Y-B phase indication lamp complete all as specified - 01 Set.

(j) Power pack of suitable capacity contained in maintenance free batteries and battery charger to provide auxiliary power supply to VCB all as per OEM's recommendation and as directed at site by Engineer-in-Charge. (k) Internal control and metering wiring with PVC insulated copper conductor cables of suitable cross sections, necessary power connections and civil work as required for installation of cable. (l) Any other standard accessories required for smooth operation of VCB or recommended by OEM.

M & L cable jointing kit for 11 KV grade cable for in door termination, heat shrink type, joint complete with jointing material and accessories suitable for 3 core XLPE, armoured, Al conductor cable of size 240 sqmm all as specified and directed.

M & L Cable jointing kit for 11 KV (Earthed) grade cable for straight through heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 240 sqmm all as specified and directed.

M&L, Cable route indicator marked with HT Cable Made of G.I Plate 3 mm Thick &150 mm dia mark with working voltage Size of cable &route fixed on M.S angle around 40x40x6 mm thick with height with height of 60 cm above the ground level &buried in grounded in PCC 1:2:4 type B1.

M & L cutting of road, hard standing made of concrete or premix carpet, WBM, soiling and stone dust filling including excavation for laying of cable pipe all as directed and making good the road/hard standing by using all old/new materials and with PCC (1:2:4) etc. required to match with the existing surface complete all as specified and directed.

WATER COOLER S&F Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type and designed for input variation between 170 Volts to 230 Volts output voltage stabilized at 230Volts with accuracy of +2.5% and of capacity of 1.0 KVA complete all as specified and directed.

Supply, installation, commissioning of water cooler fully stainless steel, electric driven single phase having approx storage capacity 80 litres and nominal cooling capacity 40 litres per hour complete all as specified and directed.

AIR CONDITIONING Supply, installation, testing and comissioning of 2 TR Capacity 230V, 50Hz, single phase Split type Air conditioning unit, 5 star rating, and EER 3.2 inverter type complete with drive motor, air cooled condenser with all accessories, varied speed and dual rotary compressor, including fixing the outdoor units as per manufacturer's recommendation and fixing of indoor (high wall) unit on wall, providing and marking interconnection including sufficient length refrigerant piping with nitryle rubber insulation and control cable from indoor unit to outdoor unit up to a distance of 3.0 mtr, power cabling (max 3.0 mtr from isolator/enclosure) to unit, first charging of refrigerant gas (R32) including cordless remote control unit, drain piping of 25 mm dia for connecting drain lines from indoor unit to maximum of 3.0 mtr to nearest drain points, outdoor support stand etc., complete all as specified and directed.

Design, supply, installation, testing & commissioning of Energy efficient Central AC plant with water cooled Screw Chillers of suitable capacity as per approved design consisting (2 working + 1 standby) for MISSION COMPLEX BUILDING(G+2) complete with sealed Screw type Single/multiple compressors, VFD starter, Shell & Tube Chiller (DX / Flooded), Water cooled shell & tube type Condenser, common Base frame / skid structure, Inter connected Copper Refrigerant piping, Vibration Isolators as per OEM recommendation, Gauge Panel, Flexible connectors at Chiller connections, Automatic Safety Controls, Ozone friendly CFC Free Refrigerant Gas R-407C/410A/134a /Green refrigerant & Oil, Nitrile Rubber Insulation on chiller, offered machine has to be BMS compatible with open protocol and micro-processor based controller with min 7" touch screen display etc to ensure proper functioning of plant to meet the inside design condition all as specified and including required equipment to achieve following parameters:

CHILLED WATER CIRCULATION PUMP: Supply, installation, testing and commissioning of monoblock, centrifugal pump, (2 working + 01 standby) suitable flow rate for approved capacity having cast iron casing, enclosed type dynamically balanced cast iron impeller, carbon steel pump shaft, gland packed sealing, deep groove ball bearings, etc. with TEFC squirrel cage induction motor having class 'B' insulation, IE3 efficiency, conforming to IS 12615: 2018 and suitable for operation on 3-Ph, 415 V, 50 Hz, AC supply, base plate, mounting channel frame, accessories and fittings, coupling guard, neoprene ribbed anti-vibration ribbed pads mounting.

CONDENSER WATER CIRCULATION PUMP: Supply, installation, testing & commissioning of monoblock, centrifugal pump, (2 working + 01 standby) suitable flow rate for approved capacity having cast iron casing, enclosed type dynamically balanced cast iron impeller, carbon steel pump shaft, gland packed sealing, deep groove ball bearings, etc. with TEFC squirrel cage induction motor having class 'B' insulation, IE3 efficiency, conforming to IS 12615: 2018 and suitable for operation on 3-Ph, 415 V, 50 Hz AC supply, base plate, mounting channel frame, accessories and fittings, coupling guard, neoprene rubber anti-vibration ribbed pads mounting.

FRP INDUCED DRAUGHT COOLING TOWER -Supply, installation, testing & commissioning of Twin Cell FRP rectangular shape, vertical, induced draught counter flow cooling tower of suitable capacity as per approved design with uniform water distribution and optimal heat transfer, having tough fiber glass reinforced plastic (FRP) casing of sufficient structural strength to withstand vibrations and wind velocity upto 60 m/s, FRP basin, rigid honeycomb type PVC fill of suitable thickness, SS sprinklers and non-clogging sprinkler pipes, FRP drift eliminator, energy efficient induced draught axial type fans with factory set and dynamically balanced blades pitch, IE3 TEFC squirrel cage induction motor, suitable for operation on 3- Ph, 415 V, 50 Hz AC supply with IP 65 protection for enclosure, conforming to IS 12615: 2018, inlet, outlet, drain and over-flow nozzle connections, etc. complete with accessories as specified and directed.- 2 Nos (1 Working + 1 Stand by) Note: Necessary civil work viz. foundation, supporting structure, etc. for placement of cooling tower shall be deemed to be included in the scope of work.

DOUBLE SKIN AIR HANDLING UNIT : Supply, installation, testing & commissioning of double skin air handling unit of suitable CFM & No. of AHU’s as per approved design. The AHU shall be single / double decker configurations as per final plant equipment’s layout. The units shall be normally in recirculation mode. The interior surfaces are completely smooth without sharp edges or welds and thus easy to clean referable with pencil covings. The double-skin type horizontal, floor-mounted, top / side discharge air handling unit of the following capacities at 65 mm static pressure, Hollow profile, with air-tight casing using gaskets and self-adhesive tapes and 0.6 mm thick pre-coated outer skin and 0.6 mm thick GI inner skin, 23±2 mm thick double skin panel with pressure injected CFC & HCFC free PUF having 'k' value of 0.02 W/°C/m & density 40 kg/m³ belt driven or plug fans with backward curved impellers for high static pressure mounted on aluminium extruded side rail base frame, suitable filter to be used for upto 10 micron and cooling coil of 6/8 row deep with anti-corrosion aluminium fins, suitable high efficiency (IE3) TEFC squirrel cage induction motor including control panels with necessary copper control cable and earthing connections, PVC/nylon hinges & handles, view port and marine lamp, limit switch, SS-304 drain pan, vibration isolators / rubber pads (minimum 1" thick) inspection windows / doors, Heater section, supply / return / fresh air openings fitted with aluminium volume control dampers complete all as specified and directed.

Note: (i) Suitable CFM as per approved design Total Static pressure for filling machine area. (ii) Rate includes for leak test and arrest complete all as specified. (iii) The temp management with RH to be controlled by suitable size of dehumidifier / humidifier with all necessary pipe, motors, heating element and its all meet with above mentioned cooling parameters.

Supply, installation, testing & commissioning of heater bank thyrister base of rating suitable capacity as per approved design operating voltage 230 V, AC 50 HZ, strip heater complete with necessary mounting arrangement shall be provided in the supply air plenum for winter heating and monsoon reheating Relative Humidity of room shall be maintained by Heating through duct mounted strip heaters, which shall be operated by humidistat and thermostat.

Supply & install, RH controller alongwith the RH Sensor Controllers accept analogue DC voltage inputs ± 5 V, 0-10 V, etc. complete all as specified and directed.

HDPE MAKE-UP WATER TANK FOR COOLING TOWER - S&F, multi-layered HDPE make-up water tank of capacity not less than 10000 ltrs to run the plant for 12 hrs, made up of 100% virgin material, having 100% UV stabilized white outer layer, more strength, flexibility and durability. FDA approved for ensures hygiene and safety of stored complete with inter-connection piping and non-return valve etc including necessary PCC/RCC platform of suitable size(height of the platform is higher than that of cooling tower) for mounting complete all as specified and directed.

CHILLED WATER TANK - S&F, multi-layered HDPE make-up water tank of capacity not less than 2000 ltrs to run the plant for 12 hrs, made up of 100% virgin material, having 100% UV stabilized white outer layer, more strength, flexibility and durability. FDA approved for ensures hygiene and safety of stored complete with inter-connection piping and non-return valve etc including necessary PCC/RCC platform of suitable size(height of the platform is higher than that of cooling tower) for mounting complete all as specified and directed.

The rate quoted by the contractor deemed to be included Supply,fixing.laying,testing and commissioning of the following item as per approved design.

(a) MS ERW PIPE Class C laid as per site requirement, conforming to IS 3589 to be used as insulated including fittings, viz. bends, tees, reducers, flanges, air purge valves, drain valves, all types of valves, structural support, necessary clamps, vibration isolators, etc. including painting and supporting / fixing the pipe in excavated trenches or on floor / wall / ceiling with clamps, hangers, angles, channels (using anchor fastener) with necessary accessories duly insulated with FM approved highly-flexible, closed-cell thermal insulation of elastomeric foam based on synthetic rubber (NBR) of 25mm thickness laminated with 12 micron aluminium foil facing with reinforced glass scrim alongwith adhesives and other necessary accessories complete .

(b)Butterfly valves, suitable dia PN 16 rating having CI grade FG 200 conforming to IS 210: 2009, seat having EPDM rubber lining, CF 8 stainless steel disc, AISI-410 stainless steel stem, 2.4 MPa body test pressure & 1.6 MPa seat test pressure and standard flange end conforming to BS 10 Table D/E & ANSI B 16.1 CI- 125 with necessary accessories including 32 mm thickness nitrile rubber insulation and 24 gauge aluminium cladding where ever required as per specifications, valves spindle shall be of extended type to accommodate the insulation thickness

(c)3-way modulating control valve suitable dia with electric actuator for AHUs. Operating Voltage 220 V AC ±10%, 110V AC ±10%, 24V AC ±10%, 50/60Hz, Working temperature: 0~50°C, Working relative humidity: 10%~90%RH, IP 20 protection, Nominal pressure: PN20

(d) Balancing valve suitable dia, PN 16 rating, automatically control the flow rate to within ±10% of its rated flow, over a temperature range of 32 to 225°F and a pressure differential range of 2 to 80 psid

(e) Cast carbon steel check valves suitable dia, dual plate type, PN 16 rating

(f) Rubber Expansion Joints for suitable dia, PN 16 rating with retainer rings & control units

(g) Pressure Gauge conforming to EN 837-1, SS casing Polycarbonate Blend Powder Coated, Max Operating Temperature 122 °F / 50 °C, aluminium range 0-10 kg/cm2, IP 66 protection, 100mm dial size alongwith SS Syphon & SS Ball valve

(h) TEMPERATURE GAUGE-S&F of 6" dual scale (°F/°C), lower mount (radial), bimetal thermometer having 0.5 NPT process connection, Grade 'A' accuracy class as per ASME B40.200, stem diameter 6.35 mm, laminated safety glass window, stainless steel 304 case, steam, process connection & joint, aluminium dial & pointer, IP67 protection, scale range 0-60 °C

(i) Ball Valve for drain purpose

(j) 'UPVC' 25 mm dia drain piping complete with fittings, U trap, supports for AHU's

(k)Air distribution system comprising of supply air/return air ducts of 120GSM duly insulated for air conditioning of building including interconnectors as required from AHU to the conditioned space comprising of class VIII galvanised sheet suitable thick with suitable supporting arrangements and bracing supply / return air grills on sheet metal frame work duly painted

(l)19mm thickness thermal insulation for supply air duct using 6mm thick class "o" closed cell nitrile rubber based Self Adhesive elastomeric insulation with reinforced aluminium foil over the exposed insulation. VOC level should not exceed more than 50 grms / Litre. Insulation manafactured as per ASTM E 84 test & which should also meet NFPA 90A supplementary materials for air distribution system which should not absorbs less 0.2% water by volume (ASTM c 209), should not support microbial growth (ASTM C1071, G21, G22) and should emit objectionable odours (ASTM C 665) and should have thermal conductivity of 0.27 (R-2.78 in 3.4" thickness) and water vapour presence of 0.10. Joints should be sealed with 50 mm wide 3 mm thick self adhesive tape & for tail-end ducting 9mm thick - CLASS - o - material.

(m)13mm thickness thermal insulation for supply air duct using 6mm thick class "o" closed cell nitrile rubber based Self Adhesive elastomeric insulation with reinforced aluminium foil over the exposed insulation. VOC level should not exceed more than 50 grms / Litre. Insulation manafactured as per ASTM E 84 test & which should also meet NFPA 90A supplementary materials for air distribution system which should not absorbs less 0.2% water by volume (ASTM c 209), should not support microbial growth (ASTM C1071, G21, G22) and should emit objectionable odours (ASTM C 665) and should have thermal conductivity of 0.27 (R-2.78 in 3.4" thickness) and water vapour presence of 0.10. Joints should be sealed with 50 mm wide 3 mm thick self adhesive tape & for tail-end ducting 9mm thick - CLASS - o - material.

(p) Powder coated, extruded aluminium, removable center core type, 4 way supply/return air diffusers/grill/ jet nozzle with aluminium collar damper for supply and without aluminium collar damper for return, The diffuser shall be mounted in the GI box, with inlet connector suitable for flexible duct. GI box & flexible duct complete all as specified and directed.

(q) Manual Volume Control Dampers - (20G) Volume made out of extruded aluminium in Mill Finish and blades of 1.55mm galvanised sheet steel. The frame is screwed together and blades held on zinc axles and acetyl bearings. All operating gear and linkages are out of the air way and concealed within the frame

(r)Fire damper blades shall be air foil shaped (equivalent to 2.3mm thickness strength) roll formed using 0.8mm thick single piece of galvanized sheet or triple V type accurately formed using 16 Gauge Steel. Pressure drop shall not exceed 20 Pa when tested at 300m/min face velocity on suitaable size damper. Fire damper is designed to be installed vertically in walls or horizontally in floors in HVAC systems with velocities to 2,000 fpm

(t)Supply, laying, jointing, testing & commissioning of suitable size, 1100Volts grade heavy duty XLPE insulated LT under ground cable, PVC sheathed, ISI marked, conforming to IS-7098 (Part-I, 1988) galvanised steel strip armoured heavy duty multi stranded copper conductor laid in trenches / passed through pipe / duct wall with clamps made out of mild steel flat iron including fixing accessories like brass cable glands double compression type, lugs, nuts, bolts, washers etc.

(u) Digital RH sensors is supply voltage 5.5 DC, operating Temperature range 40o C to 60o C and Humidity measurement range is 0 - 100% RH including control cabling form condition space to Humidity sensor complete all as specified and directed.

(v)GI earth wire 8 SWG on wall / ceiling etc with necessary fixing arrangements

(x) HOT DIPPED GALVANISED cable tray of suitable size with high tensile bolt, washers and nuts. The load bearing capacity of the cable trays should be minimum as specified. The cable trays to be manufactured with a longitudinal 'T- welded' safety edge along the top wire of the sidewall. Cable trays shall be coupled together by using 25mm/30mm counter clamp combination. The coupling must have the same surface finish as the tray. The seat of the materials should include the Trays, Couplers, Accessories for Bends and T's Supporting arrangement at the span of 1.5 meter. Colour the fabricated MS support structure Siemens grey enamelled colour with smooth finish after primer coating of red oxide complete all as specified and directed.

Design, supply, installation, testing & commissioning and validation of water cooled Screw Chillers of suitable capacity as per approved design consisting (2 working + 1 standby) for providing of ISO-Class 7(10000 CLASS) CLEAN ROOM & ISO-Class 08(100000 CLASS) CLEAN ROOM complete with sealed Screw type single/multiple compressors, VFD starter, Shell & Tube Chiller (DX / Flooded), Water cooled shell & tube type Condenser, common Base frame / skid structure, Inter connected Copper Refrigerant piping, Vibration Isolators as per OEM recommendation, Gauge Panel, Flexible connectors at Chiller connections, Automatic Safety Controls, Ozone friendly CFC Free Refrigerant Gas R-407C/410A/134a /Green refrigerant & Oil, Nitrile Rubber Insulation on chiller, offered machine has to be BMS compatible with open protocol and micro-processor based controller with min 7" touch screen display etc to ensure proper functioning of plant to meet the inside design condition all as specified and including required equipment to achieve following parameters: -

CHILLED WATER CIRCULATION PUMP: Supply, installation, testing and commissioning of monoblock, centrifugal pump, (2 working + 01 standby) suitable flow rate for approved capacity having cast iron casing, enclosed type dynamically balanced cast iron impeller, carbon steel pump shaft, gland packed sealing, deep groove ball bearings, etc. with TEFC squirrel cage induction motor having class 'B' insulation, IE3 efficiency, conforming to IS 12615: 2018 and suitable for operation on 3-Ph, 415 V, 50 Hz, AC supply, base plate, mounting channel frame, accessories and fittings, coupling guard, neoprene rubber anti-vibration ribbed pads mounting

CONDENSER WATER CIRCULATION PUMP: Supply, installation, testing & commissioning of monoblock, centrifugal pump, (2 working + 01 standby) suitable flow rate for approved capacity having cast iron casing, enclosed type dynamically balanced cast iron impeller, carbon steel pump shaft, gland packed sealing, deep groove ball bearings, etc. with TEFC squirrel cage induction motor having class 'B' insulation, IE3 efficiency, conforming to IS 12615: 2018 and suitable for operation on 3-Ph, 415 V, 50 Hz AC supply, base plate, mounting channel frame, accessories and fittings, coupling guard, neoprene rubber anti-vibration ribbed pads mounting

FRP INDUCED DRAUGHT COOLING TOWER -Supply, installation, testing & commissioning of Twin Cell FRP rectangular shape, vertical, induced draught counter flow cooling tower of suitable capacity as per approved design with uniform water distribution and optimal heat transfer, having tough fiber glass reinforced plastic (FRP) casing of sufficient structural strength to withstand vibrations and wind velocity upto 60 m/s, FRP basin, rigid honeycomb type PVC fill of suitable thickness, SS sprinklers and non-clogging sprinkler pipes, FRP drift eliminator, energy efficient induced draught axial type fans with factory set and dynamically balanced blades pitch, IE3 TEFC squirrel cage induction motor, suitable for operation on 3- Ph, 415 V, 50 Hz AC supply with IP 65 protection for enclosure, conforming to IS 12615: 2018, inlet, outlet, drain and over-flow nozzle connections, etc. complete with accessories as specified and directed - 2 Nos.(1 working + 1 stand by) Note: Necessary civil work viz. foundation, supporting structure, etc. for placement of cooling tower shall be deemed to be included in the scope of work.

DOUBLE SKIN AIR HANDLING UNIT : Supply, installation, testing & commissioning of double skin air handling unit for ISO-Class 7(10000 CLASS) & ISO-Class 08(100000 CLASS) suitable CFM No of AHU's as per design. The AHU shall be single / double decker configurations as per final plant equipment’s layout. The units shall be normally in recirculation mode. The interior surfaces are completely smooth without sharp edges or welds and thus easy to clean referable with pencil covings. The double-skin type horizontal, floor-mounted, top / side discharge air handling unit of the following capacities at not less that 125 mm static pressure, thermal break profile, with mixing box with air-tight casing using gaskets and self-adhesive tapes and 0.6 mm thick pre-coated outer skin and 0.6 mm thick GI inner skin, 23±2 mm thick double skin panel with pressure injected CFC & HCFC free PUF having 'k' value of 0.02 W/°C/m & density 40 kg/m³ belt driven or plug fans with backward curved impellers for high static pressure mounted on aluminium extruded side rail base frame, suitable filter to be used for upto 10 micron and cooling coil of 6/8 row deep with anti-corrosion aluminium fins, suitable high efficiency (IE3) TEFC squirrel cage induction motor including control panels with necessary copper control cable and earthing connections, PVC/nylon hinges & handles, view port and marine lamp, limit switch, SS-304 drain pan, vibration isolators / rubber pads (minimum 1" thick) inspection windows / doors, Heater section, supply / return / fresh air openings fitted with aluminium volume control dampers complete all as specified and directed.

Note: (i) Suitable CFM as per approved design Total Static pressure for filling machine area. (ii) High Efficiency Particulate Air (HEPA): The suitable size and number of HEPA filter and HEPA filter housing with all allied connected items should be provide in occupied clean room hall/ rooms/hanger to achieve 10000 class & 100000 class all as per site requirement all as specified and as directed. (iii) Rate includes for filling of gas leak test and arrest complete all as specified. (iv) The temp management with RH to be controlled by suitable size of dehumidifier / humidifier with all necessary pipe, motors, heating element and its all meet with above mentioned cooling parameters. (v) Testing and validation for clean room complete with testing equipment. If the 10000 class & 100000 class is not achieved, the contractor has to provide additional Hepa filters and other components to achieve the 10,000 class & 1,00,000 clean room on no extra payment basis.

Supply, installation, testing & commissioning of heater bank thyrister base of rating suitable capacity as per approved design operating voltage 230 V, AC 50 HZ, strip heater complete with necessary mounting arrangement shall be provided in the supply air plenum for winter heating and monsoon reheating Relative Humidity of room shall be maintained by Heating through duct mounted strip heaters, which shall be operated by humidistat and thermostat.

Supply & install, RH controller alongwith the RH Sensor Controllers accept analogue DC voltage inputs ± 5 V, 0-10 V, etc. complete all as specified and directed.

HDPE MAKE-UP WATER TANK FOR COOLING TOWER - S&F, multi-layered HDPE make-up water tank of capacity not less than 10000 ltrs to run the plant for 12 hrs, made up of 100% virgin material, having 100% UV stabilized white outer layer, more strength, flexibility and durability. FDA approved for ensures hygiene and safety of stored complete with inter-connection piping and non-return valve etc including necessary PCC/RCC platform of suitable size(height of the platform is higher than that of cooling tower) for mounting complete all as specified and directed.

CHILLED WATER TANK - S&F, multi-layered HDPE make-up water tank of capacity not less than 2000 ltrs to run the plant for 12 hrs, made up of 100% virgin material, having 100% UV stabilized white outer layer, more strength, flexibility and durability. FDA approved for ensures hygiene and safety of stored complete with inter-connection piping and non-return valve etc including necessary PCC/RCC platform of suitable size(height of the platform is higher than that of cooling tower) for mounting complete all as specified and directed.

The rate quoted by the contractor deemed to be included Supply,fixing.laying,testing and commissioning of the following items also as per approved design.

(a) MS ERW PIPE Class C of suitable dia for chilled water and condenser pipe lines as per design laid as per site requirement, conforming to IS 3589 to be used as insulated including fittings, viz. bends, tees, reducers, flanges, air purge valves, drain valves, structural support, necessary clamps, vibration isolators, etc. including painting and supporting / fixing the pipe in excavated trenches or on floor / wall / ceiling with clamps, hangers, angles, channels (using anchor fastener) with necessary accessories duly insulated with FM approved highly-flexible, closed-cell thermal insulation of elastomeric foam based on synthetic rubber (NBR) of 25mm thickness laminated with 12 micron aluminium foil facing with reinforced glass scrim alongwith adhesives and other necessary accessories complete .

(b) Butterfly valves, suitable dia PN 16 rating having CI grade FG 200 conforming to IS 210: 2009, seat having EPDM rubber lining, CF 8 stainless steel disc, AISI-410 stainless steel stem, 2.4 MPa body test pressure & 1.6 MPa seat test pressure and standard flange end conforming to BS 10 Table D/E & ANSI B 16.1 CI- 125 with necessary accessories including 32 mm thickness nitrile rubber insulation and 24 gauge aluminium cladding where ever required as per specifications, valves spindle shall be of extended type to accommodate the insulation thickness

(c) 3-way modulating control valve suitable dia with electric actuator for AHUs. Operating Voltage 220 V AC ±10%, 110V AC ±10%, 24V AC ±10%, 50/60Hz, Working temperature: 0~50°C, Working relative humidity: 10%~90%RH, IP 20 protection, Nominal pressure: PN20

(d) Balancing valve suitable dia, PN 16 rating, automatically control the flow rate to within ±10% of its rated flow, over a temperature range of 32 to 225°F and a pressure differential range of 2 to 80 psid

(e) Cast carbon steel check valves suitable dia, dual plate type, PN 16 rating

(f) Rubber Expansion Joints for suitable dia, PN 16 rating with retainer rings & control units

(g) Pressure Gauge conforming to EN 837-1, SS casing Polycarbonate Blend Powder Coated, Max Operating Temperature 122 °F / 50 °C, aluminium range 0-10 kg/cm2, IP 66 protection, 100mm dial size alongwith SS Syphon & SS Ball valve

(h) TEMPERATURE GAUGE-S&F of 6" dual scale (°F/°C), lower mount (radial), bimetal thermometer having 0.5 NPT process connection, Grade 'A' accuracy class as per ASME B40.200, stem diameter 6.35 mm, laminated safety glass window, stainless steel 304 case, steam, process connection & joint, aluminium dial & pointer, IP67 protection, scale range 0-60 °C

(j) Ball Valve for drain purpose

(k) 'UPVC' 25 mm dia drain piping complete with fittings, U trap, supports for AHU's

(l)Air distribution system comprising of supply air/return air ducts duly insulated for air conditioning of building including interconnectors as required from AHU to the conditioned space comprising of class VIII galvanised sheet suitable thick with suitable supporting arrangements and bracing supply / return air grills on sheet metal frame work duly painted

(m) Return air riser SS 304 grills with 60% free area minimum 1.2mm thick fitted with SS screw and complete with OBVCDs. All joints shall be soldered to make 100% leak proof. RA riser Grill(R-1) Type size 700 x 300mm.

(n19mm thickness thermal insulation for supply air duct using 6mm thick class "1" closed cell nitrile rubber based Self Adhesive elastomeric insulation with reinforced aluminium foil over the exposed insulation. VOC level should not exceed more than 50 grms / Litre. Insulation manafactured as per ASTM E 84 test & which should also meet NFPA 90A supplementary materials for air distribution system which should not absorbs less 0.2% water by volume (ASTM c 209), should not support microbial growth (ASTM C1071, G21, G22) and should emit objectionable odours (ASTM C 665) and should have thermal conductivity of 0.27 (R-2.78 in 3.4" thickness) and water vapour presence of 0.10. All ducts should be angle flanged and all joints should be filled with silicon alongwithwith 50 mm wide 3 mm thick self adhesive tape & for tail-end ducting 9mm thick - CLASS - o- material.

(o)13mm thickness thermal insulation for return air duct using 6mm thick class "o" closed cell nitrile rubber based Self Adhesive elastomeric insulation with reinforced aluminium foil over the exposed insulation. VOC level should not exceed more than 50 grms / Litre. Insulation manafactured as per ASTM E 84 test & which should also meet NFPA 90A supplementary materials for air distribution system which should not absorbs less 0.2% water by volume (ASTM c 209), should not support microbial growth (ASTM C1071, G21, G22) and should emit objectionable odours (ASTM C 665) and should have thermal conductivity of 0.27 (R-2.78 in 3.4" thickness) and water vapour presence of 0.10. All ducts should be angle flanged and all joints should be filled with silicon alongwithwith 50 mm wide 3 mm thick self adhesive tape & for tail-end ducting 9mm thick - CLASS - o - material.

(p)Terminal boxes for mounting HEPA filter in min 18G CRCA construction duly powder coated with accessories like dome nut, presure testing nob to accomodate HEPA filter of suitable size. Boxes should be provided with top connection and complete with extruded GI operated volume control dampers, for 610 x 610 mm HEPA housing table complete all as specified and directed.

(q) Manual Volume Control Dampers - (20G) Volume made out of extruded aluminium in Mill Finish and blades of 1.55mm galvanised sheet steel. The frame is screwed together and blades held on zinc axles and acetyl bearings. All operating gear and linkages are out of the air way and concealed within the frame

(r)Fire damper blades shall be air foil shaped (equivalent to 2.3mm thickness strength) roll formed using 0.8mm thick single piece of galvanized sheet or triple V type accurately formed using 16 Gauge Steel. Pressure drop shall not exceed 20 Pa when tested at 300m/min face velocity of sutable size damper. Fire damper is designed to be installed vertically in walls or horizontally in floors in HVAC systems with velocities to 2,000 fpm

(t)Supply, laying, jointing, testing & commissioning of suitable size control and power cables to and from control panel of plant room to all equipment using 1100Volts grade heavy duty XLPE insulated armoured, PVC sheathed cable, ISI marked, galvanised steel strip/wire armoured heavy duty multi stranded copper conductor laid in trenches/passed through pipe/duct wall with clamps made out of mild steel flat iron including fixing accessories like brass cable glands double compression type, lugs, nuts, bolts, washers etc. Note:- LTUG cable from sub station to plant panel only will be measured and paid separately under respective item of schedule

(v)GI earth wire 8 SWG on wall / ceiling etc with necessary fixing arrangements

(w) HOT DIPPED GALVANISED cable tray of suitable size with high tensile bolt, washers and nuts. The load bearing capacity of the cable trays should be minimum as specified. The cable trays to be manufactured with a longitudinal 'T- welded' safety edge along the top wire of the sidewall. Cable trays shall be coupled together by using 25mm/30mm counter clamp combination. The coupling must have the same surface finish as the tray. The seat of the materials should include the Trays, Couplers, Accessories for Bends and T's Supporting arrangement at the span of 1.5 meter. Colour the fabricated MS support structure Siemens grey enamelled colour with smooth finish after primer coating of red oxide complete all as specified and directed.

(u)Digital RH sensors is supply voltage 5.5 DC, operating Temperature range 40o C to 60o C and Humidity measurement range is 0 - 100% RH including control cabling form condition space to Humidity sensor complete all as specified and directed.

(v)GI earth wire 8 SWG on wall / ceiling etc with necessary fixing arrangements

(x) HOT DIPPED GALVANISED cable tray of suitable size with high tensile bolt, washers and nuts. The load bearing capacity of the cable trays should be minimum as specified. The cable trays to be manufactured with a longitudinal 'T- welded' safety edge along the top wire of the sidewall. Cable trays shall be coupled together by using 25mm/30mm counter clamp combination. The coupling must have the same surface finish as the tray. The seat of the materials should include the Trays, Couplers, Accessories for Bends and T's Supporting arrangement at the span of 1.5 meter. Colour the fabricated MS support structure Siemens grey enamelled colour with smooth finish after primer coating of red oxide complete all as specified and directed.

The rate quoted by the contractor deemed to include combined AC Plant for ISO Class 7 & ISO Class 8 clean room as per vetted designed by IIT/NIT , Same has to be duly approved by AO. The size of AHUs may be ascertained as per the size of respective AHU rooms.

Supply and fix automatic electronic voltage stablizer of 5.0 KVA Capacity, wall mounting type having features such as intelligent time delay system, Low and High Voltage cut out protection, latest IC technology to protect from power fluctuations, thermal over load protection, wide input variation between 170 V to 270 V with output voltage stablized at 220 V to 240 V with accuracy of +/- 2.5% suitable for split type air conditioner complete all as specified and directed.

Supply and install 265 Ltrs capacity frost free inverter double door refrigirator complete

Suplly & install, AIR SHOWER suitable for 3 to 4 person made up of aluminium anodized powder coated section & sheets. The unit to be provided with blower access panel at the sodes of the air shower are interlocked and operate on magenatic system. The Air shower is complete with filter assembly, motor and blower assembly for following specification suitable for CLEAN ROOM Class 10000 (02 Nos) and Class 100000 (01 No).

Standard features: (3-4 Persons) Inner dimension: 900 x 1800 x 1950 mm (W x D x H) Overall dimension: 1400 x 1900 x 2600 mm (W x D x H) Cabinet: CRCA Powder Coated Platform: CRCA with PVC Matt Doors: View Panel door Material: CRCA Powder Coated With flush double glazing glass, hardware like door closure, D handles, ball bearing butt hings etc Pre-filters Type : Flange type Media : Synthetic, Non-over polyester fiber, washable Casing : Aluminium Gasket : Neoprene Retention : 10 Micron Efficiency : 90% Pressure drop : 6 to 8 mm HEPA Filters Type : Box type Media : Ultra clean glass fiber paper-imported Casing : Aluminium Gasket : Neoprene Retention : 0.3 Micron Efficiency : 99.997% Pressure drop : 25 mm of W.C

Adjustable nozzles Blowin caliber - 30 mm Material of construction - Stainless steel Type - Adjustable Spraying wind speed 4000 - 4500 FPM Motor Blower Power supply - 3 Phase, 415 volts RPM - 2440 Exit door & entry door Audio visual alarm as a safety measure in case motor blower trips Fault acknowledgement for motor blower tripper Blower / Filter. Side mounted Flow: Vertical down and two sides Lighting Fluorescent tubes Shower during 0-120 second (Adjustable) Sound level: 85 db A ± 5 % Motor Air - Velocity: 4000 - 4500 FPM Cotrols: Motor by DOL starter. Doors by electro magnetic interlocking, overload Protection: By thermal realy, Shower duration: By Electronic timer, Emergency off: by Push Button

Note :- (i) Consolidated capacity of AC Plant for clean room class 10000 and class 100000 is to be catered. (ii) all drawings for AC plant will have to be vetted from ant iit/nit including heat load, CFM calculation, size of supply/return duct, pipe line, pumps cooling tower, chillers, condenser etc. (iii) All duct outside missio Complex and Ait building must be insulated with 26SWG aluminium cladding (iv) For All Above AC Plant design is to be Submitted by the Contractor Duly Vetted by the NIT/IIT with complete Scheme.

AREA LIGHTING Supply and fix cable junction box thermoplastic body IP 66 , size 225mmx295mmx122mm suitable for helogen free and weather proof for out door installation with metric knockout for cable entry suitable for cable size 16-35 sqmm including clamp complete

M&L Pipe bracket for street light fitting made out of 40mm dia GI pipe, medium grade, tubing bend to shape, 1.5m long fixed to pole wall including provn of two sets of clamps made out of flat iron of size 50x6 mm including of provn of bolts, nuts and washers complete all as specified and directed.

M&L for service wire of copper conductor 3 core X2.5 Sqmm for connection of light fittings . ( Used for connection of street light from Junction box)

Supply, Laying & Testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of 4 core x 10 sqmm size

LIGHTHTNING CONDUCTOR Supply and fixing porcelain/epoxy white / brown / green spacer insulator with one GI stud bolt with nut and washer with necessary drilling for bolt hole for holding / fixing roof conductor / down conductor of lightning conductor complete

Supply and fixing porcelain/epoxy white / brown / green spacer insulator with one GI stud bolt with nut and washer with necessary drilling for bolt hole for holding / fixing roof conductor / down conductor of lightning conductor complete.

Supply install testing and commissioning Booster pump sutable to operate on 415 V, 3 Phase, 50 Hz Confirming to IS- 12469 :1988 With CI Casing bronze impeller and stainless steel shaft mounted on heavy duty bearings with 35m head, 450 LPM discharge complete with all acessories and common base frame of MS channel and plates PCC foundation and suitable capacity all as per manufacture instruction/design and vibration resistant pads complete all as directed by Engineer - in - Charge

Design,Supply, install, testing & commissioning of very early warning type Fire Suppression system suitable for Clean rooms of size (6.0 x 8.155 x 4.5m consisting in 4 rooms and passage of 2.4m wide and air lock room in passage) all as per relavent NBC code complete all as specified and directed duly vetted by Govt fire safety officer.

Fire protection UL listed fluid compound of carbon, flurine and oxygen (CF3CF2C(O) CF(CF3)2) suitable for 42 bar fire supression Clean Agent i.e FK-5- 1-12 , as per approved design Electric control Head operated electrically from the Detection Control System - as per approved design Manual cum Pressure Operated Control Head for pressure actuation slave cylinders and is mounted directly on top of the salve cylinders valve with manual lever -as per approved design SS Wire braided Flexible Discharge Hose-as per approved design SS Wire braided Flexible Actuation Hose-as per approved design Brass Discharge Nozzle - as per approved design Warning Signages-as per approved design M.S. Seamless Pipes as per ASTM A 106 Gr. B, Schedule 40 with necessary fittings -as per approved design Conventional Gas Release Panel with battery backup- as per approved design UL Listed Manual metal Pull Abort Switch -as per approved design UL Listed Manual metal pull release switch- as per approved design Very early warning aspirating type conventional Photoelectric Smoke Detector - as per approved design UL listed Hooter Cum Flasher-as per approved design 2 Core x 1.5 Sqmm. Copper armoured FRLS Cable- as per approved design

Steel conduit for FRLS Cable- as per approved design Seamless Cylinder master and slave CCOE and PESO Approved, with valve assembly and pressure gauge with a safety burst disc suitable for 42 bar fire supression system with suitable cylinder and strap and accessories Note : for item no 39: Any item/material which are connected and required to complete the job for satishfactory/smooth operation is deemed to be included in rate quoted

Supply, install, test and commissioning of Fire Pump Diesel Engine driven pump set with automatic operation pressure switches as per site requirement horizontal end suction centrifugal type conforming to IS:12469:1988 with CI casing, bronz impeller and stainless steel shaft mounted on heavy duty bearing suitable for continuous operation with range of operation 0 % to 150 % of rated capacity suitable for automatic operation for fire fighting complete for delivery of water at the rate of 2280 LPM at 70 m head and running upto 1800 RPM so as to maintain a minimum pressure 7.0 kg/sqcm at the end of delivery side of pump with presure gauge and bypass arrangement for periodic testing of working of fire fighting pump set, complete with fuel tank of suitable capacity to run for 08 hrs, including common base frame of MS channel and plates, PCC foundation all as per manufacture instruction/design, vibration resistant pads complete testing for 08 hrs all as specified and directed by Engineer - in - Charge.

Supply, install, test and commissioning of electric motor driven fire fighting pump set with automatic operation as per sit requirement horizontal end suction centrifugal type conforming to IS:12469:1988 with CI casing Bronz impeller and stainless steel shaft mounted on heavy duty bearing suitable for continuous operation with range of operation 0 % to 150 % of rated capacity suitable for automatic operation for fire fighting complete for delivery of water at the rate of 2280 LPM at 70 m head and running at suitable RPM so as to maintain a minimum pressure 7.0 kg/sqcm at the end of delivery side of pump with presure gauge and bypass arrangement for periodic testing of working of fire fighting pump set, squiral cage induction motor suitable for 415 V, 3 Phase, 50 Hz complete with and including common base frame of MS channel and plates, PCC foundation all as per manufacture instruction/design and vibration resistant pads complete all as specified and as directed by Engineer - in - Charge.

Supply and laying/fixing in position Ductile Iron pipe, class K-9 with flanged ends centrifugally cast, in any length ISI marked laid in trenches including jointing with applying leak proof chemical at flanges and testing on completion complete with specials all as specified and directed of size 150 mm (6”) dia.

All as per Item No.87 above but of 100mm dia.

Supply,fixing,testing & commissioning of non return valve confirming to IS 5312 complete with rubber gasket and GI bolts, nuts and washerss etc as requred of size 150mm dia complete all as specified and directed by Engineer-in-Charge.

All as per Item No.89 above but of 100mm dia.

All as per Item No.89 above but of 80mm dia.

S&F Fire hydrant landing valve type A (single head Gun metal) of 63 mm dia conforming to IS 5290

Supply and fix 63 mm dia 15 meter long hose conforming to IS 636 complete with male and female coupling of gun metal conforming to IS 903 complete all as specified and directed

S&F gun metal fire brigade inlet connection cast iron body for connecting to external fire hydrant ring main consisting of 4-way with gunmetal instantaneous type male coupling with built in check valves and 150mm dia , flanged outlet complete with all accessories.

Supply, installation, testing and commissioning of Microprocessor based programable type Main Control Panel fabricated from 2 mm thick CRCA sheet powder coated with necessary microprocessor bassed programable type intelligent solid state soft starter, relay, contactor, Automatic phase sequence corrector, and switchgear of suitable rating installed in pump house for fire fighting pumps (main pumps, jockey pumps) complete and all as directed by Engineer-in-Charge including the following:(for mission bldg)

(i) 300Amps copper bus bar suitable for 3 phase and neutral fixed on porcelain insulator - 01 Set, ammeter with CT, auto/manual switch for each motor and votmeter and necessary interlocking arrangement, control, power wiring and earthing from panel to motor single phase preventors one for each pumps internal wiring 32 TPN MCB-01 No for battery charging & name plate engraved complete all as directed by Engr-in-charge. (ii) Microprocessor based programable type solid state intelligent relay for automatic ON/OFF operation of fire fighting pumps as per logic of standered fire fighting procedure/practice and as per relavent latest IS and as approved by GE including suitable rating of heavy duty contactors, suitable transducers, sensors, control wiring, etc. complete and all as specified and directed.

Supply, installation, testing and commissioning of Microprocessor based programable type Main Control Panel fabricated from 2 mm thick CRCA sheet powder coated with necessary microprocessor bassed programable type intelligent solid state starter for all motors, contactor, Automatic phase sequence corrector, single phase preventor and switchgear of suitable rating installed in pump house for fire fighting pumps (main pump, standby main pump,jockey pump, standby jockey pump) complete and all as directed by Engineer-in-Charge including the following:(for AIT Bldg)

(i) 500Amps copper bus bar suitable for 3 phase and neutral fixed on porcelain insulator - 01 Set, ammeter with CT, auto/manual switch necessary interlocking arrangement, control wiring all wiring and earthing from panel to motor single phase preventors one for each pumps internal wiring 32 TPN MCB for battery charging & name plate engraved complete all as directed by Engr-in-charge. (ii) Microprocessor based programable type solid state intelligent relay for automatic ON/OFF operation of fire fighting pumps as per logic of standered fire fighting procedure/practice and as per relavent latest IS and as approved by GE including suitable rating of heavy duty contactors, suitable transducers, sensors, controle wiring, etc. complete and all as specified and directed.

Supplying and installing 300mm x 50mm x 1.6mm thick size of powder coated perforated GI Cable trays including fittings with for formation not more than 17.5% joined with connectors,suspended from the ceiling with GI suspenders including bolts & nuts etc as required complete all as specified and directed.

Supply,fixing,testing & commissioning of installation control valve of cast iron body,brass/bronze working parts comprising of water motor alarm,bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser /sprinkler system activates ,pressure gauges,emergency release, strainer , pressure switch, cock valve complete with drain valve and bypass ,test control box, ball valves ,MS pipe of required size ,flanges, orifice plate, gasket etc for 150mm dia complete.

All as per item No.98 above but of size 100mm dia

All as per item No.98 above but of size 80mm dia

FIRE ALARM SYSTEM Supply and fix laying 2 core 1.5 Sqmm PVC sheathed armoured copper conductor cable 1100 Volts grade FRLS cable complete.

Supply and fix an integrated a public address and talk back facility alongwith 06 Nos loud speakers with minimum 1KW and neccessary connected accessories complete.

Supply and fix repeater panel suitable for 4 loop addressable type panel complete.

Supply and fix repeater panel suitable for one loop addressable type panel complete.

Supply and Fix, short circuit isolators

S&F, Fire exit route indicator board with inbuilt led luminaire complete set as specified of reputed make.

M&L ,for laying 6 core 1.5 sqmm armoured, multistranded copper Cable as specified in relevant IS for use in fire alarm system

Supply and install Auto dialing system (E-dialer) suitable for addressable type fire panel system consisting of Stronge capacity of 15 to 20 telephone numbers programmable type, including connection to the existing fire alarm panel and connecting to the fire station with demonstration complete

DG SET Supply, installation, testing & commissioning of silent type (DG) Diesel Engine driven generating set confirming to CPCB -IV plus having prime power rating of 200 KVA / 160 KW at a power factor of 0.8 lagging, 415 volts, AC 3 phase, 4 wire, 50Hz, 1500 RPM, alternator directly coupled with diesel engine, mounted on common base frame complete with Accoustic enclosure with inbuilt fuel tank, fuel line & accessories, PCC foundation work as per manufacturer's instructions, anti vibration pads, OEM recommended standard panel showing standard accessories and comprising the following: - (A) ENGINE (Prime Mover): Diesel Engine,multi stroke, inline multi cylinders, liquid / water cooled, turbo charged, after cooled, confirming to IS, capable of giving adequate 1500 RPM to drive alternator capable of delivering minimum 200 KVA (160 KW) at outdoor atmospheric conditions at Hyderabad and capable of taking 10% overload for one hour after 12 hours of continuous operation, complete with all standard fittings / fixtures as as specified and directed.

(i) Fly wheel housing and fly wheel. (ii) Air cleaner dry type replaceable element type with restriction indicator. (iii) Electronic governor (iv) Dual fuel filter including water separator, fuel pump, fuel injection pump (FIP) and injectors (v) Radiator, fan & water pump assembly. (vi) Forced lubrication - Pump, lub oil filter & lub oil cooler. (vii) Exhaust silencer. (viii) Exhaust gas driven trubo charger. (ix) First fill lub oil and coolant and diesel during commission and testing. (B) ALTERNATOR: Alternator shall be self excited, self regulated, brushless for 200 KW / 160 KVA at the speed of 1500 RPM at 415 volts, 50 Hz, 3 phase, 4 wire system with advance electric voltage regulator to ensure high voltage accuracy with +/- 1% with class H insulation and IP 23, directly coupled with engine through flexible coupling and confirming IS-4722 complete.

BASE FRAME & FOUNDATION: Common base frame for engine & alternator made from structural steel channel. PCC foundation including adequate number of suitable anti-vitration pads all as per the recommendation of manufacturer. ELECTRICAL STARTING SYSTEM: Electric starting system with battery charging alternator and self starter including adequate number of maintenance free lead acid battery 180AH capacity including interconnecting cables / leads with terminals complete with starting / stopping switch and voltmeter.

ACOUSTIC ENCLOSURE: Corrosion resistant, acoustic and weather proof enclosure with durable industrial locking system on doors, doors with gasket made of high quality EDPN material, with arrangement for fresh air intake for cooling of engine & alternator, extraction and discharging of hot air to the atmosphere, made out of CRCA sheet with 11 tank pretreatment process and UV resistant powder coating and high quality noise absorbant & fire retardant grade acoustic insulation material (Rockwool) complying to IS 8183 well suitable for 200 KVA DG set to reduce noise level to 75db (A), measured at 1.00, meter distance under field conditions, confirming to CPCB IV plus norms.

Enclosure will have inbuilt base frame mounted fuel tank of capacity min to run the DG set for 08hrs fabricated out of 4 SWG MS sheet mounted inside the enclosure alongwith fuel piping from tank to engine capacity as recommended by OEM with drain valve, air vent, inlet, outlet connection and suitable exhaust pipe duty cladded with glass wool and covered with aluminium sheet and exhaust trail pipe with muffer complete all as specified and directed. (F) DG SET MOUNTED INSTRUMENT PANEL: Fitted with & having digital display for the standard parameters as receommended by OEM.

AMF CONTROL PANEL: OEM made cubicle type floor mounted panel board, indoor type made out of 2mm thick CRCA sheet for load bearing member and doors and covers made out of 1.6mm thick CRCA sheet, front opening type, protection class IP-52, duly powder coated RAL 7035 (not less than 50 micron) after seven tank process, having aluminium bus bar of 400 Amps capacity for four poles, with all standard switch gear and protection, internal wiring of adequate size PVC insulated multistanded copper conductor cable etc and consisting of following: - (i) Microprocessor based four pole MCCBs for incoming and out going of rupturing capacity 35/36 KA. (ii) Heavy duty Power contactors, 315/320A, 415 volts AC3 duty for incoming and outgoing complete with all accesores and control cabling of copper conductor all as specified and dircted.

All as per item No. 109 above but of DG set of capacity 100KVA/80KW

TELEPHONE CONDUITS & LAN S&F Modular RJ 11 Socket, 1 Module, including connected item for fixing in flush box, modulure plate and junction box completed.

LIFT Design supply, install testing & commissioning MRL 08 passengers lift, speed 1.5 metre/sec, lift with single speed motor 415 volts, 3 phase, AC 50 Hz supply conforming to IS 14665, suitable to serve G + 03 upper floors with AC Variable Voltage & Variable Frequency drive (VVVF drive) complete with all standard accessories, simplex automatic & manual dual controlled operation with/without attendant, centre opening doors with door drive (electric motor driven mechanism), sliding stainless steel doors, automatic rescue device (ARD) system, 3D infra red sensor in full height of door & built in announcing system and hand sets one each in car & one each near landing door of each floor complete with firemen switch all as specified and directed

(a) Drive : Microprocessor based VVVF (b) Number of floors : 4 ( ground + 3 Upper floors) (c) Number of landing entrences: 4 ( Ground + 3 Upper floors) (d) Number and position of car entrences : one in front only (e) Position of the machinery : Directly above the lift well - Gearless (f) Lift car inside size : As per IS (g) Type/design of lift car : Stainless steel , honey comb finish (h) Car ceiling : sleek (i) Car floor : 10mm granite tiled flooring (j) Car light fitting : LED lights regular circular type

(k) Car fan (l) Type of car entrence protection : power operated centre opening sliding door-stainless steel- Honey comb finish (m) Type of landing entrence protection : centre opening sliding door-stainless steel- Honey comb finish (n) Type of landing door frame : stainless steel- Honey comb finish (o) Clear opening of gates : As per IS (p) In addition to the above the following provisions/accessories/items shall be provided:-

(i) Dot matrix LED D&P indicators in car and landing - Orange colour(ii) Push button - Orange LED illumination.(iii) Battery operated emergency light and alarm bell.(Rechargeable type)(iv) Call register signal and Vf door operator(v) False ceiling in car(vi) Infra red door screen.(vii) Vandal proof SS button with SS cover.(viii) Automatic rescue device with 3 continous operation with visual display in COP and audio.(ix) Over load warning indicator.(x) Fireman's switch.

(xi) Intercom provision with instrument.(xii) Arrival Gong.(xiii) Braillr buttons.(xiv) Full length mirror and SS hand rail on rear side.(xv) Floor annunciator with music. (xvi) Pit ladder.(xvii) Full car operating panel- Press N speek phone.(xviii) Arrangement of inspection by LIFT inspector for approval/Commissioning of the lift by authorised lift Inspector from the state Govt. (xix) Obtaining license from Govt.(xx) Training of Departmental personnel.(xxi) Submission of operating and maintenance mannual.(xxii) Any other minor builders works necessary for completion of LIFT work.

Note :- (1) The rate is deemed to be included the necessary strip earth as per IS norms & as per site requirement and as directed by Engineer-in-charge.(2) UG cable from main panel to machine room control panel will be measured and paid seperately.

EOT CRANE Design Supply, installation, testing and commissioning of electrically operated, overhead traveling (EOT) cranes of capacity 5 Ton,suitable for clean room conforming to IS : 3177 (latest revision), with span 24 mtrs (approx), hook height of 06 mtrs (approx), long travel length upto 40 mtrs (approx), suitable for operation on 415 Volts, 3 Phase, 4 wires, 50 Hz supply, double girder box type, with Hoist speed 2mtrs / min, cross travel speed 5 mtrs / min, long travel speed 10 mtrs / min with micro drives through VVVF drive system with control panel, power and controlling cables, confirming to relevant latest IS, controlled by pendent push button station and RF remote control switch for operation, with and including of steel rope suitable dia with DSL busbar System of shrowded type, complete all as specified and directed.

SPECIAL EARTHING M&L for Maintenance free chemical Earthing consists of earth electrode CU (Copper) bonded stell rod 17.2mm dia 3000mm and 250 microns back filled with 30 kg carbon based compound including 17.2mm tin coated brass clamps both sides. the pit shall be installed with a man hole with top cover including laying of 25 x 3mm copper strip from earth pit to panel/equipment upto 7.5 m using 40 mm GI Pipe light grade buried in ground from earth pit to building equipment earth strip including earth Resistance measurement and provide test report all as per direction of Engineer-in- Charge. Note : The earth resistance value for each location should be less than 1.0 Ohms and to measure and calibrated with earth resistance megger and same has to be certified by concerned user department..

Schedule A Part XVIII Comprehensive maintenance preventive maintenance & periodical maintenance of electrically operated overhead travelling (EOT) 5 Ton capacity EOT Cranes - 01 complete including material and labour for periodic inspection/ servicing to be carried out and making/ keeping the cranes serviceable complete all as specified and directed. (i) LONG TRAVEL MONTION AND CROSS TRAVEL MOTION (a) Checking gear box oil level and filling with required oil and rectification of leakages if any (b) Brake adustment (c) Checking of long travel & cross travel wheel for any noise/ malfunctioning (d) Checking grease of greard couplings, nut tightening and replacement of grease nipple. (e) Checking of oil in Hydraulic thruster brake, rectification of leakages if any and filling with required quantity of oil. (f) Checking of electric motor connections, insulation resistance value etc. (g) Checking the cut off at extreme ends with the limit shitch (h) Checking and greasing of shaft pedestal

(ii) HOIST MOTION (a) Checking gear box oil level and filling with required oil and rectification of leakages if any (b) Brake adustment (c) Checking main bearings of the rope drum including greasing the same . (d) Checking grease of geard couplings and nut tigthening . (e) Checking of oil in Hydraulic thruster brake, rectification of leakages if any and filling with required quantity of oil. (f) Checking of electric motor connections, insulation resistance value etc. (g) Checking wire rope for any damage & greasing the rope. (h) Adjustment of the rotary limit switch (j) Checking of bearing of the hook and greasing the same.

(iii) ELECTRICAL PANEL (a) Checking the contactors for overheating or flashing (b) General checking of contacts and connections. (c) Cleaning of control panels and checking of connectionas (d) Checking of connections of VVVP drives/other drives, calibrating VVVF drive to get smooth movement & maximum efficiency / other drives for smooth functioning of the same.

Schedule A Part XIX Comprehensive maintenance preventive maintenance & periodical maintenance of MRL 08 passengers lift, speed 1.5 metre/sec, lift with single speed motor 415 volts, 3 phase, AC 50 Hz supply conforming to IS 14665, suitable to serve G + 03 upper floors with AC Variable Voltage & Variable Frequency drive (VVVF drive) complete with all standard accessories, simplex automatic & manual dual controlled operation with/without attendant, centre opening doors with door drive (electric motor driven mechanism), sliding stainless steel doors, automatic rescue device (ARD) system, 3D infra red sensor in full height of door & built in announcing system and hand sets one each in car & one each near landing door of each floor complete with firemen switch all as specified and directed

CNR INFRATECH (BID ID -3482014)

SRICO PROJECTS PVT LTD (BID ID -3492297)

HTE INFRA LLP (BID ID -3492022)

vijay infraprojects pvt ltd (BID ID -3492279)

NSC Projects Pvt. Ltd. (BID ID -3490877)

Sri Raghava Constructions Ltd (BID ID -3489974)

NIMMA NARAYAN ENGINEERS AND CONTRACTORS (BID ID -3490582)

SHRADHA SABOORI PROJECTS INDIA PRIVATE LIMITED (BID ID -3482368)

SVC PROJECTS PVT. LTD (BID ID -3488420)

SOOD ASSOCIATES PVT LTD (BID ID -3492353)