Lake front development at Perumbakkam

Amount

Civil Works

Earth work excavation for all foundations in all type of soils and sub soils to the required depth for Footings, plinth / grade beams, etc,. by mechinaries including manual excavation for the following type of soil / rock as per detailed specification. As per SS 20B as hard rock requiring blasting inclusive of shoring strutting and baling out water wherever necessary and including refilling 0 to 2.0m depth consolidation depositing the surplus earth in places shown clearing and leveling the site with an initial lead of 10 metre and lifts as specified hereunder etc., complete in all respects complying with relevant standard specification and as directed by the departmental officers.

Carting away surplus excavated earth available with in the campus is to be carted to a lead of within 10 KM from site. The rate shall include loading into the tipper/ lorry transporting and unloading, leveling and the earth scooped by bulldozers grading etc.,complete with all respects complying with relevant standard specification, as directed by the Departmental Officers. Rate to include materials, loading, unloading, transportation, plant and machinery, hire and fuel charges for tools and plants and other incidental charges, royalties, seignorage and taking statutory approvals as necessary to carry out the work as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Providing UNDER REAMED PILES R.C.C.30cm (12") dia cast-in-situ with single reamed (bulb) in cement concrete 1:1.5:3, 11.5cm above G.L. including boring, erecting, vibrating,curing, hire charges for drilling equipments, etc.,complete as per relevent ISI specifications(excluding cost steel reinforcement).

Providing and constructing cast in situ hydraulic bored piles of specified diameter in M30 grade concrete using blended cement - slag cement with minimum cement content of 400kg/m³ in accordance with the structural engineers drawings and directions, but exculding reinforcement including cost of mobalization of all necessary plants, equipment's like piling rigs, temporary casing of appropriate length for setting out cardinal points and the removal of the same, boring in overburden, using bentonite mud circulation technique or any other method duly through all strata upto the foundation level of piles etc., complete all as approved by the departmental engineer. Further include dewatering, placing concrete by tremie pipe method, disposal of bored material outside the site. Including Chipping carefully cut off portion of piles as required without any damage to the piles and dressing the top and removing all the debris away from the site with out any extra cost as directed including the cost of all tools, plants, conveyance, all labour, lead and lift required etc .,Conducting standard penetration test to identify the refusal strata for atleast 1 pile in group and atleast 25% of piles, comparing with refusal strata as indentified in soil report and providing socketting into refusal strata by 1.00mt or into hard rock by 100% dia of the pile. (Length of pile for payment shall be measured up to bottom of pile cap).

600mm Dia Pile

Providing and constructing cast in situ hydraulic bored piles of specified diameter in M30 grade concrete using blended cement - slag cement with minimum cement content of 400kg/m³ in accordance with the structural engineers drawings and directions, but exculding reinforcement including cost of mobalization of all necessary plants, equipment's like piling rigs, temporary casing of appropriate length for setting out cardinal points and the removal of the same, boring in overburden, using bentonite mud circulation technique or any other method duly through all strata upto the foundation level of piles etc., complete all as approved by the departmental engineer. Further include dewatering, placing concrete by tremie pipe method, disposal of bored material outside the site. Including Chipping carefully cut off portion of piles as required without any damage to the piles and dressing the top and removing all the debris away from the site with out any extra cost as directed including the cost of all tools, plants, conveyance, all labour, lead and lift required etc .,Conducting standard penetration test to identify the refusal strata for atleast 1 pile in group and atleast 25% of piles, comparing with refusal strata as indentified in soil report and providing socketting into refusal strata by 1.00mt or into hard rock by 100% dia of the pile. (Length of pile for payment shall be measured up to bottom of pile cap).

450mm Dia Pile

Carrying out initial working pile load test on specified dia piles as specified in IS:291 1 (Part 4). Includes all plant, equipment, machinery. instruments, measuring devices, platforms and kentledge pile caps etc., dismantling and carting away entire setup, excavation and dewatering etc., all complete

600mm Dia Pile

Carrying out initial working pile load test on specified dia piles as specified in IS:291 1 (Part 4). Includes all plant, equipment, machinery. instruments, measuring devices, platforms and kentledge pile caps etc., dismantling and carting away entire setup, excavation and dewatering etc., all complete

450mm Dia Pile

Supplying and Filling with M - sand in foundation and others sub structures for 100mm thick and well watered, rammed and consolidated by power compacter. The rate includes the cost of M sand, compacting with mechanical compactors, labour charges for leveling, loading & Unloading and Transportation charges etc., complete and as per the standard specification

Construction of Granular sub-base of 150mm compacted thickness by providing laying, spreading and compacting of Close graded Material conforming to Grading V of Table 400-1 of MORTH clause 401 ,mixing in a Wet Mix Plant of 200 tonne capacity at OMC, carriage of mixed material to work site, spreading in uniform layers withmotor grader o n prepared surface and compacting with vibratory roller 8-10 tonne to achieve the desired density of 98% including protection of edges of GSB layer, cost of all materials, labour, hire charges of machinery, lighting, guarding, barricading maintenance of diversion road loading & unloading, all lead and lift etc., to achieve minimum CBR value of 30%(Compacted Thickness) in accordance with MORTH technical specification clause No. 401 and with all other incidental charges and as per the direction of the Engineer-In-Charge of work

Providing and laying plain cement concrete 1 : 4 : 8 ratio of (1 cement , 4 M sand and 8 graded stone aggregate 40mm nominal size) in foundation and basement including dewatering wherever necessary and laid in layers not more than 15 cm thick and consolidation etc. The rate includes the cost of materials, labour charges, lifting charges, loading & Unloading and Transportation etc., complete and as per the standard specification.

Supplying and erecting centering for sides and soffits including supports and strutting up to 3.30 m height with all cross bracing for plane surfaces as detailed below, using mild steel sheets of 90 X 60 cm 10 gauge stiffened with MS angle of 25 X 25 X 3mm for boarding, laid over adjustable span & jacks and supported by 50mm dia pipes for general pipes scaffolding systems @ a spacing of 1.20m c/c and vertical connected at a height of 2.0m c/c including 'C' & 'U' clamps and base receiver cup at bottom for connecting pipes etc and removable systems etc., the rate including cost of all materials, labour charges, wastages, placing, transportation, lead & lifts, tools & plants, fuels, fixing in position at all levels, heights, masking tape in sheet joints, consumables, etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge. b)For column footing plinth beam bed blocks templates staircase, steps piers, raft beam, raft slab etc.

For Plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For column footing plinth beam bed blocks templates staircase, steps piers, raft beam, raft slab etc.

for plane surfaces such as rectangular or square rcc columns, sunshades, top and bottom slab of rcc boxing, etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical walls etc.

Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 400 kg/ms and maximum water cement ratio of\ |0.45, including admixture (plasticiser/ super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of |concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone 10 jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of sand, but |excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical |vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards

For Foundation and Basement

For Grond floor Upto 4.5m height

Supplying, fabricating and fixing in position of steel Fe 550 grade Reinforcement for all RCC work with Thermo Mechanically Treated Bars (TMT) conforming to IS 1786 of latest version according to drawings and binding the reinforcement with 18 gauge double fold GI binding wire and providing Concrete cover blocks to maintain the cover as required. The rate including cost of all materials, bending, tying grills, placing, transportation, lead & lifts, tools & plants, fuels, all materials, labour charges, wastages , laying at all levels, fixing in position, cost of cover blocks and GI binding wires etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Supply and constructing cement concrete solid block masonry work at all levels in cement mortar 1:5 (1 of Cement : 5 of manufactured sand ) using Portland Pozzolana Cement standard size of 400 x 200 mm and 200 mm thick of solid cement concrete with minimum compressive strength of 5 N/Sq.mm.conforming to IS 2185 or equivalent BS and Fly ash conforming to IS : 3812 (Part III)-1966* may be used for part replacement of fine aggregate up to a limit of 20 percent complete and as directed. Concrete blocks manufactured under strict quality control conditions using modern rugged block casting and stripping machine with the latest moulding techniques etc,. only shall be used. Rate to include all materials, labour charges, wastages for working at all levels with necessary lead and lifts, transportation charges, loading, unloading, scaffolding, staging, curing, fuel, consumables as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

Rate for foundation and Basement

Rate for Ground Floor

Supply and constructing cement concrete solid block masonry work at all levels in cement mortar 1:5 (1 of Cement : 5 of manufactured sand ) using Portland Pozzolana Cement standard size of 400 x 100 x 200 mm of solid cement concrete blocks, with minimum compressive strength of 5 N/Sq.mm.conforming to IS 2185 or equivalent BS and Fly ash conforming to IS : 3812 (Part III)-1966* may be used for part replacement of fine aggregate up to a limit of 20 percent. Concrete blocks manufactured under strict quality control conditions using modern rugged block casting and stripping machine with the latest moulding techniques etc. only shall be used. The rate including cost of all materials, labour charges, wastages for working at all levels with necessary lead and lifts, transportation charges, loading, unloading, scaffolding, staging, curing, fuel, consumables as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Rate for foundation and Basement

Rate for Ground Floor

Supply and constructing good quality Chamber Brick masonry work for 115mm Thk Kerb walls as per architect details

Supply and Laying good quality Chamber Brick Flooring over well compacted earth as per architects details

Providing and constructing Lattrite size stone masonry with cement mortar 1:6 , edges of stones chistle dressed in courses not less than 15 cms high, bond stones at two m. apart in cach course lincluding cost of materials Labour, scaffolding. curig complete as per specifications

Providing Soil Profiling including cutting and removing excess earth as per architectural Plan

Supplying & Providing Stone Pitching using Lattrite Blocks as per architectural Details

Suuplying & Laying liner in pond area using Coir Fibre & Timber Pegs as per architectural Details

Supplying & laying Clay soil in the pond area 150mm Thk

Supplying & Laying 25mm Beige River pebbles to lay 25Sqm of Space approximate qunatity required is 800 Kg

Supplying & Laying Greyish White Granite Rock as per architectural details

Supplying & Laying 0.5mm/1m Greyish White Rock Boulder one side dressed with engraving for Directions

Supplying & Laying 0.5mm/.6m Greyish White Rock Boulder one side dressed with engraving for Directions

Plastering of 12 mm thick for Internal walls with cement mortar 1:5 (1 of cement : 5 of P sand) according to specifications. Rate shall include for providing GI mesh of nominal thickness at the junctions of masonry and concrete works to a width of 100 to 125mm including tying in position with suitable clamps/screws. The rate including cost of all materials, labour charges, wastages with necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, scaffolding, stagging, tools and plants, fuel, curing, cleaning, consumables etc as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Plastering 10 mm thick for ceiling including slabs, beams and column drops and staircase waist slab, sunshade, drops, chajjas etc..with Cement Mortar 1:3 (1 of cement : 3 of P sand) according to the specification. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, scaffolding, stagging, providing drip bands, moulds to any size and shape as shown in drawings tools and plants, fuel, curing, cleaning, consumables etc as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Plastering 15 mm thick for external surfaces with Cement Mortar 1:5 (1 of cement : 5 of P sand) with water proofing compound of “CICO No.1 or equivalent“ as per Manufacturer's Specification with sponge finish (washed sand finish) all complete as per specification and as directed. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, scaffolding, stagging, providing drip bands, moulds, grooves to any size and shape as shown in drawings tools and plants, fuel, curing, cleaning, consumables etc as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supply and painting of two coats of Acrylic emulsion paint of approved shade and colour over one coat of DCP Primer including one coat of Acrylic Wall Putty with DCP Primer. Rate including all brush, roller, ladder, scrapping, washing, materials, labour charges, wastages , cleaning, necessary lead and lifts, scaffolding, stagging, working at all levels, elevations, transportaion charges, loading, unloading, curing, sanding, touchup putty, surface thoroughly cleaned and wetted before painting as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.(Ceiling & Internal surface)

Supplying and painting of 2 coats of weather proof exterior emulsion with high sheen, anti algal properties over one coat wall exterior primer of approved quality and shade etc., complete. The rate including cost of materials, brush, ladder, scrapping, washing, materials, labour charges, wastages , cleaning, necessary lead and lifts, scaffolding, stagging, working at all levels, elevations, transportaion charges, loading, unloading, curing, sanding, touchup putty, surface thoroughly cleaned and wetted before painting as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supply and painting of Concrete Texture Scratches 1mm of approved texture, shade and colour and three coats of Apex Paint of approved colour over one coat of DCP Exterior Primer including two coat of Asian Wall Putty with DCP Primer

3mm ACP WITH UV CLEAR STICKER PRINT FIXED ON MS Section Designing, Providing and fixing in position Hot rolled structural steel Members / Sections consists of MS joists, channels, angles, purlins, pipes, hollow tubes, runners, insert plates, flats etc. at all levels. Surface preparation of all MS members by Sand blasting to SA 21/2 grade and painted with anti corrosive, low VOC PU paint (metallic finish) with compatible primer to a minimum film thickness of 75 microns and 2 coats of low VOC PU paint of Akzonoble make and total dry film thickness 225 microns. (Only Main structural supports related to Facade works if required any shall be considered and no base frame or support structure shall not be consider, which shall form part of the respective cladding and Glazing items). Refer Particular Specification for Mode of measurement for this item.

Supply & Fixing of Bird Sculptures Dimensions: * The tallest bird will be 6.5 feet high. * Remaining heights will be as per the reference image. * Each bird will be around 2 feet wide, proportionate to its height. Materials: * Birds will be made from corten steel sheets. * Vertical support pipes will be G.I pipes, painted for contrast.

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from unplasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug.

Supplying And Fixing of Rubber Moulded Grey Premium Concrete Kerb of Size 450X125X300mm Using M30 Concrete. The Concrete Shall Be Moulded By Table Mount Vibrated With Polypropylene Fibers At 5% And Curing Compound. The Rate Shall Include Cost of Materials Transportation Loading Unloading Charges And All Taxes Including Necessary Earth Work Pointing With cm. 1:3 To Full Depth Curing Thread Lining Etc Complete .

Design Supplying And Fixing of 200X100X60mm Rubber Moulded Gray Colour Premium Concrete Pavers as per Architectural Drawings Using M30 Concrete Placed Over 50mm Thick Crushed Stone Sand (M Sand). The Concrete Shall Be Moulded By Table Mount Vibrated With Polypropylene Fibers At 5% And Curing Compound. The Rate Shall Include Cost of Materials Transportation Loading Unloading Charges And Including Filling of All Joints With Labour Charges Etc.

Design Design Supplying And Fixing of Tactile Paver as per Architectural Drawings Using M30 Concrete Placed Over 50mm Thick Crushed Stone Sand (M Sand). The Concrete Shall Be Moulded By Table Mount Vibrated With Polypropylene Fibers At 5% And Curing Compound. The Rate Shall Include Cost of Materials Transportation Loading Unloading Charges And Including Filling of All Joints With Labour Charges Etc.

Supplying Fixing Epdm Flooring as per Arch. Design Supply of EPDM Flooring 36mm (30 mm SBR Buffing + 6mm EPDM) Includes Primer, Buffing, EPDM Granules, PU Binder, etc. all inclusive of Installation & Transportation

Supplying Fixing Grass liners Gray Colour 300X300X80mm as per Arch. Drawings Using M30 Concrete Placed Over 50mm Thick Crushed Stone Sand (M Sand). The Concrete Shall Be Moulded By Table Mount Vibrated With Polypropylene Fibers At 5% And Curing Compound. The Rate Shall Include Cost of Materials Transportation Loading Unloading Charges And Including Filling of All Joints With Labour Charges Etc.

Supply and laying flooring with best quality the following materials of Black Flamed granite slab not less than 25 mm thick in CM 1:4 (1 of cement : 4 of manufactured sand) 20 mm thick including finishing the joints with white cement slurry, cutting, edge chamfering to approved shape and polishing rough, medium, nice and tin-oxide polish. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts working at all levels, transportaion charges, loading & unloading, preparation of surface, ncessary haccking in RCC surface, cutting to required shape, edging, tools and plants, fuel, curing, cleaning, acid wash over finished surface, protection with Gypsum / Pop layer over plastic sheet and removing the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Polishing and Nosing the Granite Slab To Half Edge to round shape and finishing the surface neatly etc. complete complying with standard specification as directed by department officers

Nosing of Granite - Single Nosing (M-0245)

Nosing of Granite - Double Nosing (M-0246)

Supplying and laying of Flooring with Joint free double charged vitrified tiles of approved quality, colour and design joint free of size 600 x 600 x 8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (one cement three sand) 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40 kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officers. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.. (Including Skirting)

Providing Ceramic tiles of size 305 x 305 x 6mm flooring approved make and quality with plain/colour with base mortor in CM 1:3, 10mm thick and pointing with white cement by adding suitable colour pigments including finishing, jointing and polishing with neat finish etc., complete.

Supplying and fixing Dadooing the wall with ceramic tiles of approved quality, colour and design joint free of size 600x300x10mm thick of approved make, in all floors over a base layer of cement mortar 1:2 (one cement: Two sand) 10mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40 kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supply and laying water proofing treatment for bottom and sides of RCC pond covering the following order and consisting of following operations. Supply and laying water proofing treatment for bottom and sides of RCC pond covering the following order and consisting of following operations. Supply and laying water proofing treatment for bottom and sides of RCC pond covering the following order and consisting of following operations. iii) Sealing off the nozzles and level the surface using integral Waterproofing compound CICO NO.3 or approved equivalent in the ratio 1:1by weight.iv)The concrete slab shall be thoroughly cleaned to remove debris and dust, and application of two coats not less than 2 mm thick of TAPECRETE - RTU Polymer Based Elastomeric Waterproof Coating over well prepared surface

Terrace Waterproofing Supply and laying water proofing treatment for terrace covering the following order and consisting of following operations. i) Making V' grooves at the construction joints of size 20 x 20 mm and filling the "V" Groove with CICO No. 3 Quick Setting Waterproofing Compound admixed with cement.The roof slab gutter slab shall be thoroughly cleaned to remove debris and dust, and applying 2 coats not less than 2 mm of polymer based Elastomeric Coating like TAPECRETE - RTU compound and cured for 7 days and followed by a layer of 20 mm thick cement mortar 1:3 admixed with CICO NO: 1 (or) other approved equivalent make shall be spread over the prepared surface

The gap cement mortar 1:4 admixed with compound like CICO NO:1 or approved equivalent afterwards curing shall be carried out for two days a final layer of cement mortar of 1:3 admixed with water proofing compound like CICO NO:1 or approved equivalent make shall be laid to a thickness of 20 mm and draw a false line of 300 mm x 300 mm.

On the spread mortar provide and lay well burnt brick bats (COBA) to a average minimum thickness of 55 mm (i.e.. minimum 40 mm thickness at lower end and 70 mm thickness at higher end). An additional layer of brick bat (COBA) shall be laid over the existing brick bat COBA surface if required to get the required gradient for adequate drainage giving a slope of approximately 1 in 120, which will be measured separately under relevant item.

The parapet side wall / gutter wall shall be thoroughly cleaned to remove all dust particles and a layer of 15 mm thick C.M 1:3 shall be laid to a height of about 300 mm above the top of the terrace/Gutter slab on the Parapet / Gutter side wall admixed with water proofing compound like the CICO NO:1 or approved equivalent make. Providing, supplying, mixing, applying two coats of ready to use two component Acrylic polymer modified cement based, flexible, water proofing slurry like or approved equivalent to a thickness of 2 mm over the plastered surface of operation as per manufacturer's specification and as directed.(Plan area of Terrace only will be measured for payment )

Designing, Providing and fixing in position Hot rolled structural steel Members / Sections consists of MS joists, channels, angles, purlins, pipes, hollow tubes, runners, insert plates, flats etc. at all levels. Surface preparation of all MS members by Sand blasting to SA 21/2 grade and painted with anti corrosive, low VOC PU paint (metallic finish) with compatible primer to a minimum film thickness of 75 microns and 2 coats of low VOC PU paint of Akzonoble make and total dry film thickness 225 microns. (Only Main structural supports related to Facade works if required any shall be considered and no base frame or support structure shall not be considere, which shall form part of the respective cladding and Glazing items). Refer Particular Specification for Mode of measurement for this item.

Supplying and fixing of 0.5mm thick galvanised steel sheet prefabricated sandwich 50mm thick PUF panels with rigid PUF injected CFC/ HCFC free (Zero ODP) blowing agent Pentane polyurethane foam as insulation and galvanized steel sheet with slight ribs with 180 gsm. zinc coated for base metal and 20 Micron Polyester coating over 5 Micron primer 0.50mm thick on both sides as skin materials and having density of not less than 40 kg/m3 for self supporting wall panels of cold room chambers and pre cooling room complete for all lengths including wall panel capping Flashing with PPGI / ‘Z’ Flashing and sealant for joints of panels and height as directed by the departmental officials and as per standard specification. (Rate as per Quotation inclusive of all Labour, Material & Transportation) Brand Metro PUFF off white, Male ANMS)

Providing and laying non-pressure class NP2 RCC Spun pipes with collars including excavation of trenches in soil/murum/rock, laying the pipes as per layout and drawing, filling the joints with stiff mixture of cement mortar (1 part cement :1part fine sand) and jute, curing, testing the pipe and refilling the trenches in layers with due compaction & watering etc. complete as directed

Toilet Cubicles SPECIFICATION Profile : Venesta Hardware Make-Chung /2 Track Window-Frame :60 mm /55mm, 2.5 mm Outer wall thickness, /3Track - 112 mm /Door-Shutter66mm/50mm/Windows -Shutter :55mm/39mm/Openable Windows-Frame :60 mm/58mm , 2.5 mm Outer wall thickness/Windows - 76mm/38mm - 2.5 mm Outer wall thickness Openable Windows-Frame :60 mm/58mm , 2.5 mm Outer wall thickness/Windows -76mm/38mm - 2.5 mm Outer wall thickness Outer wall thickness/Windows -76mm/38mm - 2.5 mm Outer wall thickness/Nylon Rollers-SS 304 Grade/Reinforcement Pure. G.I- 1mm/Touch lock Espag Multi Point- Zinc alloy/Glazing Gaskets- EPDM/Wool Pile-Waterproof Wool Pile/Fire Retorant. ProfilesyES/ Windows Glass-5 mm Plain Glass (Saint Gobain)/Ventilator-4 mm Pinned. Glass/Silicon Sealants-V- Tech (Nippon) (VT 223) ( Interiors and Exteriors)/Anchor Fasteners-8mm x 80 mm, 16.Profile warranty - 15 year /Hardware warranty- 1 year

Supplying and Fixing Everwood composite EWD145x25 deck board fitted on hollow aluminium joist EWD50x30EDx1.5mm framework. Framework fitted on floor with intervals not exceeding 350mm c/c with Aluminium clamps & N8/60 screws as designed. Composite plank fitted on joist with SS304 grade start & end clips / PA grade center clips fastened with corroshield 7x25CSK screws. Necessary sides to be covered with EWD57X10 trims as specified as per Architectural Detail for Decking in Bund Area

Supplying and Fixing Everwood composite EWD145x25 deck board fitted on hollow aluminium joist EWD50x30EDx1.5mm framework. Framework fitted on floor with intervals not exceeding 350mm c/c with Aluminium clamps & N8/60 screws as designed. Composite plank fitted on joist with SS304 grade start & end clips / PA grade center clips fastened with corroshield 7x25CSK screws. Necessary sides to be covered with EWD57X10 trims as specified as per Architectural Detail for Decking in Bird Watching Tower.

Supplying & Fixing Everwood composite EWD75X20 board fitted on powder coated hollow aluminium joist 50x25x1.5mm framework with corroshield screws as specified. Aluminium framework is fastened to slab with Aluminium clamps & N8/60 screws as per drawings and specifications. As per Architectural Detail for Seater

Supplying & Fixing Everwood composite Vertical & Horizontal profile EWD100x40 with powder coated MS tube 50x25x2mm inserts is fitted existing MS framework with corroshield screws as per drawings and specifications. As per Architectural Details for Railing.

Supplying & Fixing Everwood composite profile EWD100x40 (Without MS inserts) is fitted existing MS framework with corroshield screws as per drawings and specifications. As per Architectural Details for Vertical Fins in Interpretation Building.

Supply & Fixing Everwood composite profile EWD100x40 with powder coated MS tube 50x25x1.6mm inserts is fitted existing MS framework through MS brackets with corroshield screws as per drawings and specifications

Supplying & Laying River Sand Pit upto 300mm in the play area

Providing Nammatype modular Toilet block of 2 toilet cabins for 1 ladies & 1 Gents Toilet with Indian seat ,Size 3x4x7 , 2 SS wash basins, Light point in each Toilet & ventilation. FRP cabin Toilets 40 mm insulated wall panels, SS railings for outer shed. Cabin walls with luster finish..

Providing Nammatype modular Toilet block 1 Cabin with 2 Urinal Size 4x4

Supply & Fixing of Dustbin Product Code : ULDB - 04 Constructed with MS Sheet with WPC Duly Galvanized and Polyster Powder Coated. Size-900x400x650 mm Capacity of 75 ltr

Supply & Fixing of Dustbin Product Code : ULDB - Indoor Perforated Round Dustbin for Dry Waste

Supplying & Fixing of 1100 Ltr Metal Dustbin without Lid. MS Galvanised Sheet 2mm thickness weight 110-120kg Approximately

Supplying Fixing Seater Product Code :ULB-02 (WITH BACKREST) Constructed with MS Sheet with WPC Duly Galvanized and Polyster Powder Coated. Size:1500 x 450 x 850 mm

Supplying Fixing Seater Product Code :ULB-02 (WITHOUT BACKREST) Constructed with MS Sheet with WPC Duly Galvanized and Polyster Powder Coated. Size:1500 x 450 x4 50 mm

Supplying & Fixing of Badmiton Court Net all inclusive of transportation

Supplying & Fixing of Volley Ball Post all inclusive of transportation

Supplying & Fixing of Football Post all inclusive of transportation

Supply and fixing of Wave Slide 8ft FRP: [Component] Ladder : Galvanished ‘B’ Class pipe Sliding chute 9ft BED LEG :Galvanished ‘C’ Class pipe Height :5ft FRP thickness 4mm. (Reinforced Polymers in 5 Layers) 450 CSM Matt, 600 Roving Mat, Isotolic gel coat with PU pigment. Painting with PU coating width :2ft [Required area] Product area :21/2’ft * 12’ft

Supply and fixing of See-Saw 4 Seater FRP: Height :1 ½ ‘ft Width :5’ft Frame : 1 ½” Galvanished ‘B’ Class pipe See saw Rail :2” Galvanished ‘C’ Class pipe Seat : FRP Seat with 450 CSM Mat 3 Layers bonding. Isotolic gel coat with UV pigment. Painting with PU coating seat size : 15”ft * 14”ft Product area : 5’ft * 10’ft Play area:8’ft * 12’ft

Supply and fixing of Kiddies Safe Rotor Platform:16 gauge GI sheet & MS angle .LEG-3”GI pipe,Seat-16 gauge GI sheet Product area : Ø 7’ft Play area : Ø 10’ft

Supply and fixing of Swing 2 seater Height of 7ft 0” above the ground level and width of 10ft 0”. Legs made of 40mm Stainless Steel pipes and Cross Bars made of 50mm SS pipes Seats fiber reinforced plastic seats suspended with 6mm thick in coated chain etc.

Supply and fixing of Double Bar / Parallel Bar Frame:1/2”GI pipe, 2.5mm thick, B class, height:41/2’, product size:6’*2’ paint: pu coating

Supply and fixing of DOUBLE CROSS WALKER Cardio, lower/ upper body exercise. Main Post made of 4 Inch Pipe and other main pipes 1-1/2 inch Pipes. 3 mm thickness pipes (1680 x 515 x 1780 mm) 4 mm pipe Double coat Powder coating, Heavy duty Branded sealed Ball bearing, for long lasting life. Steel Foot rest / Foot Paddle for long lasting life. (Arihant, RMI, Ankidyne or Equivalent Brand)

Supply and fixing of ARM & SHOULDER WHEEL Supply, Erection and Fixing of Arm & Shoulder Wheels 1300 x 1200 x1350 mm 4mm pipe Main Post made of 4 Inch Pipe and other main pipes 1-1/2 inch Pipes. 3 mm thickness pipes Double coat Powder coating, Heavy duty Branded sealed Ball bearing, for long lasting life. (Arihant, RMI, Ankidyne or Equivalent Brand)

Supply and fixing of Hip Twister – Double persons sitting standing any combination Height :21/2”Pipe, 11/4”pipe, 3/4”pipe, 2.5mm thick, B class, height:41/2’ product size:5’*1’ Paint:pu coating.

Supply and fixing of SEATED CHEST PRESS Size (1850 x 800 x 2050 mm) Main Post made of 4 Inch Pipe and other main pipes 1-1/2 inch Pipes. 3 mm thickness pipes Thick rexine covered cushioned seat Double coated Powder coating, Heavy duty Branded sealed Ball bearing, Steel Foot rest / Foot Paddle for long lasting life. (Arihant, RMI, Ankidyne or Equivalent Brand)

Supplying and fixing of Elliptical Trainer (Arihant, RMI, Ankidyne or Equivalent Brand)

Supplying and fixing of Hand Rover (Arihant, RMI, Ankidyne or Equivalent Brand)

Bund Works

Dismantling & removing the existing Plain Cement Concrete work etc., by using required mechinaries and disposal of unserviceable material within 50m lead, labour charges, as per direction of Engineer in charge.

Dismantling, Removing & the existing pavers as Instructed by Engineer In Charge with lead upto 50m

Earth work excavation for all foundations in all type of soils and sub soils to the required depth for Footings, plinth / grade beams, etc,. by mechinaries including manual excavation for the following type of soil / rock as per detailed specification. As per SS 20B as hard rock requiring blasting inclusive of shoring strutting and baling out water wherever necessary and including refilling 0 to 2.0m depth consolidation depositing the surplus earth in places shown clearing and leveling the site with an initial lead of 10 metre and lifts as specified hereunder etc., complete in all respects complying with relevant standard specification and as directed by the departmental officers.

Carting away surplus excavated earth available with in the campus is to be carted to a lead of within 10 KM from site. The rate shall include loading into the tipper/ lorry transporting and unloading, leveling and the earth scooped by bulldozers grading etc.,complete with all respects complying with relevant standard specification, as directed by the Departmental Officers. Rate to include materials, loading, unloading, transportation, plant and machinery, hire and fuel charges for tools and plants and other incidental charges, royalties, seignorage and taking statutory approvals as necessary to carry out the work as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Supplying and Filling with M - sand in foundation and others sub structures for 100mm thick and well watered, rammed and consolidated by power compacter. The rate includes the cost of M sand, compacting with mechanical compactors, labour charges for leveling, loading & Unloading and Transportation charges etc., complete and as per the standard specification

Construction of Granular sub-base of 150mm compacted thickness by providing laying, spreading and compacting of Close graded Material conforming to Grading V of Table 400-1 of MORTH clause 401 ,mixing in a Wet Mix Plant of 200 tonne capacity at OMC, carriage of mixed material to work site, spreading in uniform layers withmotor grader o n prepared surface and compacting with vibratory roller 8-10 tonne to achieve the desired density of 98% including protection of edges of GSB layer, cost of all materials, labour, hire charges of machinery, lighting, guarding, barricading maintenance of diversion road loading & unloading, all lead and lift etc., to achieve minimum CBR value of 30%(Compacted Thickness) in accordance with MORTH technical specification clause No. 401 and with all other incidental charges and as per the direction of the Engineer-In-Charge of work

Providing and laying plain cement concrete 1 : 4 : 8 ratio of (1 cement , 4 M sand and 8 graded stone aggregate 40mm nominal size) in foundation and basement including dewatering wherever necessary and laid in layers not more than 15 cm thick and consolidation etc. The rate includes the cost of materials, labour charges, lifting charges, loading & Unloading and Transportation etc., complete and as per the standard specification.

Supplying and erecting centering for sides and soffits including supports and strutting up to 3.30 m height with all cross bracing for plane surfaces as detailed below, using mild steel sheets of 90 X 60 cm 10 gauge stiffened with MS angle of 25 X 25 X 3mm for boarding, laid over adjustable span & jacks and supported by 50mm dia pipes for general pipes scaffolding systems @ a spacing of 1.20m c/c and vertical connected at a height of 2.0m c/c including 'C' & 'U' clamps and base receiver cup at bottom for connecting pipes etc and removable systems etc., the rate including cost of all materials, labour charges, wastages, placing, transportation, lead & lifts, tools & plants, fuels, fixing in position at all levels, heights, masking tape in sheet joints, consumables, etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge. b)For column footing plinth beam bed blocks templates staircase, steps piers, raft beam, raft slab etc.

For column footing plinth beam bed blocks templates staircase, steps piers, raft beam, raft slab etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical walls etc.

Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 400 kg/ms and maximum water cement ratio of\ |0.45, including admixture (plasticiser/ super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of |concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone 10 jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of sand, but |excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical |vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards

For Foundation and Basement

Supplying, fabricating and fixing in position of steel Fe 550 grade Reinforcement for all RCC work with Thermo Mechanically Treated Bars (TMT) conforming to IS 1786 of latest version according to drawings and binding the reinforcement with 18 gauge double fold GI binding wire and providing Concrete cover blocks to maintain the cover as required. The rate including cost of all materials, bending, tying grills, placing, transportation, lead & lifts, tools & plants, fuels, all materials, labour charges, wastages , laying at all levels, fixing in position, cost of cover blocks and GI binding wires etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Plastering 15 mm thick for external surfaces with Cement Mortar 1:5 (1 of cement : 5 of P sand) with water proofing compound of “CICO No.1 or equivalent“ as per Manufacturer's Specification with sponge finish (washed sand finish) all complete as per specification and as directed. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, scaffolding, stagging, providing drip bands, moulds, grooves to any size and shape as shown in drawings tools and plants, fuel, curing, cleaning, consumables etc as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supplying and painting of 2 coats of weather proof exterior emulsion with high sheen, anti algal properties over one coat wall exterior primer of approved quality and shade etc., complete. The rate including cost of materials, brush, ladder, scrapping, washing, materials, labour charges, wastages , cleaning, necessary lead and lifts, scaffolding, stagging, working at all levels, elevations, transportaion charges, loading, unloading, curing, sanding, touchup putty, surface thoroughly cleaned and wetted before painting as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Design Supplying And Fixing of 200X100X60mm Rubber Moulded Gray Colour Premium Concrete Pavers as per Architectural Drawings Using M30 Concrete Placed Over 50mm Thick Crushed Stone Sand (M Sand). The Concrete Shall Be Moulded By Table Mount Vibrated With Polypropylene Fibers At 5% And Curing Compound. The Rate Shall Include Cost of Materials Transportation Loading Unloading Charges And Including Filling of All Joints With Labour Charges Etc.

Design Design Supplying And Fixing of Tactile Paver as per Architectural Drawings Using M30 Concrete Placed Over 50mm Thick Crushed Stone Sand (M Sand). The Concrete Shall Be Moulded By Table Mount Vibrated With Polypropylene Fibers At 5% And Curing Compound. The Rate Shall Include Cost of Materials Transportation Loading Unloading Charges And Including Filling of All Joints With Labour Charges Etc.

PLUMBING & SANITARY FIXTURES

Supply and fixing in position white European Water Closet of approved make with low level flushing tank 10 litre capacity of best quality and approved make with 100mm P or S trapwith double flapped rigid PVC seat cover with CP brass hinges etc. complete complying with standard specification and as directed by the Departmental officers (The EWC should be got approved by the Executive Engineer before use on works.

Supplying and fixing of CP Two Way Bib Cock with Health Faucet ,wall hook & one metre long flexible tube including cutting and making good the walls wherever required etc complete. complying with standard specification and as directed by the Department officers. The quality and make of health faucet should be got approved by Concern department Engineer before use on work.

Supplying and fixing of Brass Chromium Plated Screw Down including cutting and making good the walls wherever required etc complete. complying with standard specification and as directed by the Department officers. The quality and make of health faucet should be got approved by Concern department Engineer before use on work.

Wash Hand Basin of size 550 mm X 400 mm with all accessories such as cast Iron Brackets, 32 mm Dia C.P. Waste coupling, Rubber plug and Chain, 32 mm dia ' B ' Class G.I. Waste pipe, 15 mm Dia G.M Wheel valve; 15 mm Dia Nylon connection, 15 mm Dia Brass Nipples, 15 mm C.P. Pillar tap etc.,including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and as directed by the Department officers. The quality and make of below counter Wash basin should be got approved by department Engineer before use on work. ( all Inclusive of cost of basin, Bottle Trap and Angle Cock)

Supplying and fixing in position Bottle Trap of following dia of best approved quality conforming to BIS, etc., complete complying with standard specifications. (The Bottle trap should be got approved by the Executive Engineer before use on works).

Supplying and fixing Lipped Mouth Porcelain Flat Back Urinal(white colour) of size 26.5x31.5x44cm with all accessories such as 32mm dia Bell Mouth PVC Connection, 15mm dia GM Wheel Value, 15mm dia 'B' Class GI Waste Water Pipe, 15mm dia Nylon Connection, 15mm dia Brass Nipple, and suitable screws, shellac etc., complete. The rate including cost of all materials, labour charges for fixing and transportation etc. completed as directed by Engineer-in-Charge.

Providing and fixing in position vertically marble partition in the urinals with Raj Nagar marble stone of white hard, dense hemogenious colour without cracks, and fissures of size (3.0+2.0)5'height thickness varies from 18 to 20mm including making grew in the wall and pointing and packing with cement mortar 1:3 polishing, finishing on both sides etc., as directed at site. (GCC 2023-2024)Si.No. 603, Schl No.874

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed Various Sized and 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks) .

Size 600X450X5.5mm Thk

Supplying and fixing of Paper Holder with cover ,wall hook including cutting and making good the walls wherever required etc complete. complying with standard specification and as directed by the Department officers. The quality and make of health faucet should be got approved by Concern department Engineer before use on work. Make LUXUS

Supplying and fixing in position Waste Coupling of following dia of best approved quality conforming to BIS, etc., complete complying with standard specifications. (The waste coupling should be got approved by the Executive Engineer before use on works).

Supplying,installing,testing and commissioning of approved make CONCEALED STOP COCK including neccesary accessories etc, complete,works include making require size curout in wall,and fixing the control box property,redoing the same etc,complete the quality and make of concealed stop cock should be got approved by concern department Engineer before use on work.

Supplying and fixing the best quality approved make of Angle Cock with wall flange including cutting and making good the walls wherever required etc. complete complying with standard specification and as directed by the department officers. The quality and make of angular stop cock ahould be got approved by concern department engineer before use on work

Supplying & fixing in position 15 mm dia brass/ C.P pillar tap (Heavy duty) of approved make conforming to I.S. Specifications & quality including cost of shellac, thread etc., complying with standard specifications & including cutting & threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the work).

Supplying and fixing in position PVC cowls of following dia of best approved quality conforming to BIS, etc., complete complying with standard specifications. (The PVC cowl should be got approved by the Executive Engineer before use on works).

110mm Dia

75mm Dia

Supplying & fixing in position PVC Nahini / Floor trap of size 100x75mm including stainless steel gratings of approved brand & quality, fixed over a bed of brick jelly lime concrete 1:2:5 ( One part of lime, two parts of sand & five parts of 40 mm size brick jelly ) & finished with cement mortar 1:3 ( One cement & three sand ) including dismantling masonry works wherever found necessary & making good the damaged portions to the original condition & giving connections to the cast iron pipes etc., complete, complying with standard specification. (The PVC Nahini / Floor trap should be got approved by the Executive Engineer before use on works ).

Supplying & fixing in position 150 X 100 mm square mouth 'P' or 'S' trap stone ware Gully trap 'A' grade with cast iron gratings of size 300 X 300 mm with C.I. air tight cover with frames of size 300 X 300 mm at bottom & top respectively with necessary earth work excavation, laid over a bed of brick jelly cement concrete 1:3:6, 150 mm thick using 20 mm size broken brick jelly including necessary block work & plastering, &including dismantling masonry wherever necessary & redoing the damaged portions to the original condition & by using cement concrete 1:3:6 using 20 mm stone jelly for fixing the Gully trap & giving connections to the stone ware sewer line etc., complete, complying with standard specification. (The stone ware gully trap should be got approved by the Executive Engineer before use on works ).

Constructing brick masonry manhole with second sort Solid Blocks in CM 1:5 (one of cement, Msand) including earthwork excavation and sand filling for a depth of 150mm top cover slab with CC 1:2:4 (one of cement, two of sand, four of graded aggregate) 20mm nominal size for fixing C.I Frame, including shuttering, reinforcement foundation concrete 1:4:8 (one of cement, four of sand, eight of graded aggregate 40mm nominal size) 100mm tk., plastering inner, outer and other exposed surface with 15mm tk., cement mortar 1:3 (one of cement, three of sand) and finishing with a floating coat of neat cement with water proofing compound as per specification, making channelsin CC 1:2:4 (one of cement, two of sand, four of graded aggregate) neatly finished including fixing C.I. Cover and frame, C.I. Rungs etc., complete complying to standard specification.

Supply and fixing RCC precast slab manhole cover SFRC of 50mm thick and required size 900mm x 900mm made in CM 1:3 Ratio both direction including cost and conveyance of all materials, labour and transportation etc complete complying with standard specification.

Supplying and fixing in position the best quality and variety sizes PVC soil and waste pipes 6Kg /10Kg / cm2 of ISI mark, providing leak proof joints etc and making connection to all sanitary fittings, including dismantling masonry / RCC works wherever necessary and making good the portions. The quality and make of PVC pipes and specials should be got approved by Concern department Engineer before use on work.

160mm Dia Pipe

110mm Dia Pipe

75mm Dia Pipe

Supplying, laying and jointing UPVC pipes of approved quality and best variety conforming to ISS and with ISI mark of the following size including cutting, threading and fixing PVC specials but excluding cost of such specials and fixing to wall with necessary teak wood plugs, PVC clamps and screws, making good the portions to original condition with necessary brick work and concrete plastering wherever necessary with necessary scaffolding charges etc. complete complying with standard specification and as directed by the Department officers. The quality and make of UPVC pipes and specials should be got approved by Concern department Engineer before use on work.

20 mm dia UPVC pipe

25 mm dia UPVC pipe

32 mm dia UPVC pipe

40 mm dia UPVC pipe

65 mm dia UPVC pipe

Supplying & fixing in position first quality & approved variety of various dia U.P.V.C Ball Valves ( Heavy type ) with I.S.I. Mark of the following size including cost of Shellac, thread etc.,including labour for cutting & threading of Pipes etc., complete complying with standard specifications for both internal & external water supply arrangements.

Supplying and fixing in position first quality and approved variety of Gun Metal /brass valve /airrelease valve /Check valve (Heavy type)with ISI mark of the following sizes including cost of Shellac,thread etc,including labour for cutting ,threading and fixing position of CPVC Pipes for both internal external water supply arrangements etc,complete complying with standard specification and as directed by the Department officers. The quality and make of valve should be got approved by Concern department Engineer before use on work

Supply ,erection and testing & commisioning of 2HP submersible pumpset in the to suit 200mm borewell of capacity of 4800 LPH @ 265Ft, max. total head of 280 Ft pumps fitted with bronze impellers and having delivery size of 40mm - 430V along with 3mts cable and manufactures standard control panel which is mandatory and as directed by the officer incharge and other required supporting items like SS hose nipple, nylon rope, clamps, bolt and nuts,GI nipple, 40mm dia HDPE hose of required length etc completed and as directed by the officer incharge.

Supply, installation, testing and commissioning of equivalent to Ingersoll Rand Reciprocating Air Cooled Type (10 HP) Rating Vaccum Pump as per following provisions. As per IS 12827 / 1987 & ISO 7396 / 1987 Specification a) Vaccum Pump - 10 HP - 1 No. b) Electric Motor - 10 HP - 1 No. c) DOL Starter with OLR - 1 No. d) Vaccum Switch - 1 No. e) Vaccum Gauge - 1 No. f) Control Frame with Fittings - 1 No. g) Suction Scrubber - 1 No. h) V-Belts - 1 No. i) GI & MS Fittings - 1 No. j) Brass Fittings - 1 No. k) Exhaust Silencer - 1 No. i) Base Frame for Motor and Vaccum Pump - 1 set m) Pilot Line with Fittings - 1 set, Vaccum Room & Air Compressor Room Inside

Supplying and erecting in position of following liters capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact.

Construction of Modular type RWH Structure capacity of 4.32 cu.m by using infiltration modules of size 800 x 800 x 360 mm and side wall with infiltration modules of size 800 x 360 x 25 mm including earthwork excavation in bitumen/concrete roads to a size of 1200 x 1200 x 3000 mm and providing base plate, Geo - textile 400mm - 200 micron, Fine filter media 12mm thickness, Coarse filter media 20mm thickness, FRP of 700x700mm (clear opening 600x600mm) (Grating cover with Frame - Medium duty 10 MT), including all labour charges, carting away and drilling bore well 150mm dia upto a depth of 3m with 125mm dia Blue slotted PVC Pipe., complete. (Model 6)

Supply & Fixing of PVC Water tank. Brand Syntex including all accessories & Transporation

3000Ltr Tank (Rate as per Quotation)

Supply & Fixing OF Bio Septic Tank of 3000ltr Capcity including all Loading, Unloading & transporation

Supplying and Fixing Hindware matrix Set for physically handicapped toilet with W/c, Urinals and all accessories.

Supplying & Fixing Pressmatic taps urinal Auto Valve closing systems will accessories

Supply and installation of a open drip kit that consits of 16mm dia drip lines of length 20m connected to 23 m long 37.5 MM HDPE lateral capped at the end per block, as per Engineer instruction.

16mm drip lines -1400Rmt

End drip caps fittings - 720 No.s

Rubber drip fitings - 720 No.s

Offtake connectors drip fittings - 720 No.s

50 MM Main screen filter - 1 no

Start connectors without rubber - 720 No.s

Start connectors with rubber - 720 No.s

16mmHDPE (PE pipes) 360 Rmt

ELECTRICAL WORKS

CT Metering Panel - Supply, Installation, Testing and Commissioning of CPRI approved make of panel, cubicle type, Free standing, floor mounted, single front, 14 SWG CRCA sheet steel, enclosed separate compartment for each feeder, front operated, Powder coated, indoor type dust and vermin proof, hinged lockable doors, complete with electrolytic grade copper bus bars, internal wiring, colour coding, ferrules, Panel mounting MS Channels, fasteners, etc., including all associated control wiring. 1set of 200/5A CT with TNEB Metering provision and 1nos of 200/5A CT for APFCR . (Rate as per Quotation)

200A Isolator Panel - Supply, Installation, Testing and Commissioning of CPRI approved make of 200A TPN MCCB panel, cubicle type, Free standing, floor mounted, single front, 14 SWG CRCA sheet steel, enclosed separate compartment for each feeder, front operated, Powder coated, indoor type dust and vermin proof, hinged lockable doors. (Rate as per Quotation)

Fabrication, Supply, Erection, Testing and Commissioning of whether proof CRCA sheet steel made up of 2mm powder coated MCCB Indoor Type Three Phase Changer Over panel of size (H 1450 X L 1400 X D 400 ) mm with suitable to accommodate 200A 4 pole Three phase Change Over Switch-1No. as incomer for EB Source and as incomer for DG Source , 1no 160A 4Pole MCCB, 6nos of 125A 4Pole MCCB, and 2nos of 63A 4Pole MCCB's, compartment for as O/G supply with the provisions to accommodate Busbar chamber and cable chamber with size of 33x6mm copper busbar 4 runs having three phase Multifunction meter with line indicators and with all necessary accessories with all other connected works etc. The panel made up of 16/18 SWG CRCA sheet steel comprising of 4 sections with separate sheet steel weatherproof and shock proof safety insulation system conforming to IE Rules with IP protection, and with the panel should be painting by powder coating finishing etc.,as complete and making good of the panel with neat finishing. (Switch make : L & T / ABB) panel should be earthing confirming ISI specifications. The panel should be erected on Anchor fastners, bolts and nuts for mounting the Indoor Panel as directed by engineer-in charge/department superior engineers.

VERTICAL THREE PHASE MCB DISTRIBUTION BOARD WITH MCB : Supply and fixing of 4 way vertical TPMCB sheet steel Industrial Type TPMCB DB with IP54 Protection of surface type fitted with bus bars and neutral links with1 No. of 100A FP MCB as Incoming and 12 Nos.of 32A,10KA Triple Pole MCB in Flush with wall and making good of the concealed portion with earth connection.( Industrial Type TPMCB DB with IP54 Protections) ( SR 2023-2024, P.no: 148)

Supply and fixing of 7 segment 8 way 63A TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and separate 4 way provision for accommodating one no. 4 pole incoming 63 A TPN MCB, 10kA, / Isolator and another separate 4 way for accommodating one no. 63 Amps, 30 mA, 4 pole ELCB / RCD (totally 8 ways in one segment) and 24 nos 6-32 A, 10kA, SP MCB / Isolators ( totally 24 nos.) for outgoing in 3 segments with label holder and provision for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only. (SD 716)

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 25A FP ELCB switch as incoming and 4 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher End ( SD-594)

Supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonry pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED Street light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED street light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour (SD 543)

Supply and Fixing of 40W 4' LED Tube Light with PVC unsheathed copper leads from terminals to the fitting. (Make : Philips/Crompton/Havelles ) (SD-526)

Supply and Fixing of energy efficient Outdoor type 12W LED Facade Light fixtures in die cast aluminium housing with colour temperature of 3000k which offers beautiful ambient lighting with IP65 Protection. Model equivalent to Crompton, Philips or Bajaj.

Supply and fixing of 1200mm (48") sweep AC ceiling fan 5 star rated complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 2.5 metre down rod with fan clamp, and wiring to the near by point with 1.5 sqmm FRLS , PVC insulated copper wires, including necessary accessories and hardware's as required. (SD -563)

Supply and fixing of 300mm(12")sweep (Heavy duty) AC Exhaust fan complete with necessary wall opening and making good of the wall and wiring to the near by point with 1.5 sqmm FRLS PVC insulated copper wires including necessary accessories and hardware's as required. (SD-115)

Supply and fixing of louvers shutter arrangements for 300mm(12")sweep (Heavy duty) AC Exhaust fan complete (SD-120)

Supply and laying of following XLPE armoured LTUG cable in a trench/Tray with suitable cable tie tag etc as required.

Supply and laying of 31/2 core 120 Sq.mm PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (SD-751)

Supply and Laying of 3 1/2 x 95 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 3 1/2 x 70 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (SD-749)

Supply and Laying of 3 1/2 x 50 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.(SD-748)

Supply and Laying of 3 1/2 x 35 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.(SD-747)

Supply and Laying of 31/2 x 25sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (SD-746)

Supply and Laying of 4C x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.(SD-745)

Supply and laying of 4CX6sqmm Cu. armoured LTUG Cable in the existing cable trench

Supply and laying of 4CX4sqmm Cu. armoured LTUG Cable in the existing cable trench

Supply and laying of 3CX2.5sqmm Cu. armoured LTUG Cable in the existing cable trench

Supply and Laying HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.(SD-745)

Supply and clamping of following XLPE armoured LTUG cable on post or on wall MS-Clamps , Saddles, plugs, Screws etc., as required.

Supply and Clamping of 3 1/2 core x 120 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable. (SD-227)

Supply and Clamping of 3 1/2 core x 70 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable. (SD-225)

Supply and Clamping of 3 1/2 core x 50 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable. (SD-224)

Supply and Clamping of 3 1/2 core x 35 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable. (SD-223)

Supply and Clamping of 3 1/2 core x 25 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable. (SD-222)

Supply and Clamping of 4C x 16 Sq.mm PVC armoured LTUG aluminium cable on post or on wall with MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable. (SD-221)

Supply and fixing of double compression brass cable gland for following Aluminium conductor XLPE insulated armoured cable of 1100 V grade with earth connection.

Supply and fixing of brass cable gland for 3 1/2 C x 120 Sq.mm PVC LTUG armoured cable with earth connection (SD-191)

Supply and fixing of brass cable gland for 3 1/2 C x 70 Sq.mm PVC LTUG armoured cable with earth connection (SD-189)

Supply and fixing of brass cable gland for 3 1/2 C x 50 Sq.mm PVC LTUG armoured cable with earth connection (SD-188)

Supply and fixing of brass cable gland for 3 1/2 C x 35 Sq.mm PVC LTUG armoured cable with earth connection (SD-187)

Supply and fixing of brass cable gland for 3 1/2 C x 25 Sq.mm PVC LTUG armoured cable with earth connection (SD-186)

Supply and fixing of brass cable gland suitable for 4C x 16 PVC armoured LTUG cable with earth connection.(SD- 183)

Supply and providing cable end termination of the following size PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (copper sockets for copper cables and Alu. Sockets for alum. Cable)

Supply and providing cable end termination of 3 1/2 Core x 120 Sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete. (SD-240)

Supply and providing cable end termination of 3 1/2 Core x 70 Sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete. (SD-238)

Supply and providing cable end termination of 3 1/2 Core x 50Sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete. (SD-237)

Supply and providing cable end termination of 3 1/2 Core x 35Sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete. (SD-236)

Supply and providing cable end termination of 3 1/2 Core x 25Sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete. (SD-235)

Supply and providing cable end termination of 4 C x 16sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping with electrical connection complete. (SD-235)

Supply and providing cable end termination of 4 X 6 Sqmm PVC LTUG Copper cable with necessary copper cable sockets by crimping etc, with electrical connection complete. (SD-235)

Supply and providing cable end termination of 4C X 4 Sqmm PVC LTUG Copper cable with necessary copper cable sockets by crimping etc, with electrical connection complete. (SD-235)

Supply and providing cable end termination of 3C X 2.5 Sqmm PVC LTUG Copper cable with necessary copper cable sockets by crimping etc, with electrical connection complete.

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) ( 4points / Coil) Higher End (SD-333)

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with Module GI switch box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection by 1 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for PVC concealed light (6 points per coil) (for rooms like bath, toilet & pumproom, etc.). (SD-26)

Wiring with 3R x1.5 sq.mm. (22/0.3) PVC insulated unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with continuous earth wire connection of 1 run of 2.5 Sq.mm wire and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point Higher End (SD-355)

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with painting of suitable colour for concealed PVC pipe Plug point ( 8 points / Coil) Higher End (SD-375)

Wiring with 2 x 4 sq.mm. (56/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 16A one way module switch and 1 no. 16A 3/2 pin module socket with module front plate with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with painting of suitable colour for Concealed PVC pipe power Plug point ( 8 points / Coil) Higher End (SD-385)

Supply and Run of 4 of 6 sq.mm. (84/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire with painting of suitable colour. (SD-442)

Supply and Run of 2 of 4 sq.mm. (56/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour. ( SD 430 )

Supply and Run of 2 Run x 2.5 sqmm and 1R of 1.5sq sqmm PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable Pvc conduit pipe on concealed wall and ceiling with continuous earth wire connection with painting of suitable colour. ( SD 428)

Supply and fixing of thermoplastic loop - in and loop out boxes with lid of dimension min 104X104X70MM with 20A connector. shorting link 2 way necessary and along DIN rail terminal block. The Junction Box shall be insulated and made out of high grade thermoplastic. The JB shall be IP Rated for outdoor applications, environment friendly, recyclable, UV resistant, halogen & silicon free, anti acid& anti corrosive. The JB shall be rated for Degree of Ingress Protection IP 65 in accordance with IEC 60529.

Supply and fixing of 1no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Scope cover wall cutting , grouting , flushing and making good on the wall. Higher End. (SD 464 )

Supply and fixing of 2nos.6A two module 5 pin socket , 2 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Scope cover wall cutting , grouting , flushing and making good on the wall. Higher End. (SD 470 )

Supply and fixing of manufacturer's GI metal back box and 3 nos of 6A modular switch, 3nos of 6A 3 pin combined modular type wall socket in flush with wall mounted on poly carbonate front plate with switch mounting metal parts, in flush with wall. (SD-476)

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Scope cover wall cutting , grouting , flushing and making good on the wall. Higher End.- (SD 488)

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 50mm and 2 mtr long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs of carbon based environment friendly backfill compound and suitable clamp and with copper earth plate of size 125mm x 50mm x 6mm with necessary funnelling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry SD-233

Supply, Installation, Testing and Commissioning of earthing station consisting of 600 x 600 x 3 mm. thick, copper Plate earth electrode, back filling with alternate layer of charcoal, salt, brick masonry work for chamber 450 x 450 mm. heavy duty CI cover, watering pipe, funnel and earthing conductor as per IS:3043 specification. All civil works required such as excavation in all types of soils, rocks, PCC Earthing Chamber foundation, reinstatement and making good the surface to match original, removal of surplus earth etc. are included.(Rate as per Quotation)

Coil earth to street light poles with No.8 SWG GI wire of 11.5 metres of length in which 10 metres of total length compressed in to a coil of one meter length (75mm to 100mm dia) connected suitable with hexagonal earth bolt of size 8mm in to 25mm welded on the pole at one end with a coil position fixed on the earth. ( SD 78)

Supply, fabrication, of GI /Copper earth flat of following size in provided trench, clamping in wall, ceiling, with suitable Clamps/ saddles, connecting the joints through bracing / welding covering with termination in the earth pits, Panels, Distribution boards and equipments with bitumen paint including accessories wooden plugs, screws, fastener etc., all inclusive

Supply and run of 25mm x 6mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection (SD-76)

Supply and run of 25mm x 6mm GI flat with necessary clamps / supports on wall / floor / ground for earth connection (SD-77)

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection (SD -458)

Supply and Run of 1 of No.8 SWG GI wire in suitable PVC rigid pipe on wall / floor / ground for earth connection (SD -459)

Supply and Run of 2 of 10 sq.mm. (140/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with painting of suitable colour.

Supply, installation, testing and commissioning of Electronic Hooter / Sounder providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers (Make: Ravel / Equivalent) (SR-2024-25, pg-126, M-0772)

Supply and laying of FRLS PVC insulated 2 core 1.5 sq.mm. Armoured Copper Cable on ceiling / wall using fixing accessories like screws, plug, clamps, etc., asper standard methods and as directed by the Departmental Officers.(SR-2024-25, pg-126, M-0773)

CCTV SYSTEM

Supply, Installation, Testing and commissioning of 32 channel 8 SATA NVR, with 6T Hard Disk Drive 4 nos, New logical and visualized GUI design Dual-OS design to ensure high reliability of system running, ANR technology to enhance the storage reliability when the network is disconnected, Configurable normal or hot spare working mode to constitute an N+1 hot spare system Video Input and Transmission, Connectable to the third-party network cameras Compression and Recording, H.265+ compression effectively reduces the storage space by upto 75%, Full channel recording at up to 12MP resolution HD Video Output  HDMI1 / VGA1 outputs provided  HDMI1 Video output at up to 4K ( 3840 × 2160 ) resolution Storage and Playback, Upto 16 SATA interfaces and 1 eSATA interface for HDD connection, Support upto 10TB capacity for each HDD, Smart search for efficient playback. and smart playback to improve the playback efficiency, Supports VCA search for fire/ship/temperature/temperature difference detection triggered video files, POS information overlay on live view and playback, POS triggered recording and alarm Network & Ethernet Access  Hik-Connect for easy network management, 2 Gigabit Ethernet network interfaces. (Make : Hikvision / Dahua / Sony (Rate as per quotation)

Supply, Installation, Testing and commissioning of 16 channel NVR with 4TB HDD * 4nos, Up to 16-ch 8 MP IP cameras can be connected, Connectable to the third-party network cameras Compression and Recording, H.265+ compression effectively reduces the storage space by up to 75%, Full channel recording at up to 12MP resolution HD Video Output  HDMI1/VGA1 outputs provided  HDMI1 Video output ) resolution Storage and Playback, Up to 4SATA interfaces and 1 eSATA interface for HDD connection, Support upto 6TB capacity for each HDD, Smart search for efficient playback. (Make: Hikvision/Dahua/Panasonic) (Rate as per quotation)

Supply of 8MP, Internet Protocol fixed BULLET CAMERA with following specification: ●1/2.5" Progressive Scan CMOS, ● 3840 × 2160 @15 fps,2.8/4 mm fixed lens,01 lux @ (F1.2, AGC ON), 0.028 lux @(F2.0, AGC ON), 0 lux with IR, H.265+, H.265, H.264+, H.264, 2 Behaviour analyses ( Line crossing detection, intrusion detection) ● Face Detection ● 120dB WDR, ● BLC/3D DNR/ROI, IP67 complied ●On-board Storage - Built-in micro SD/SDHC/SDXC card slot, up to 128 GB, ● Shutter Speed 1/3 s to 1/100,000 s, ● 3-Axis Adjustment Pan: 0° to 360°, tilt: 0° to 100°, ● rotate: 0° to 360°, 2.8 mm, ● horizontal FOV: 102°, vertical FOV: 53°, diagonal FOV: 124°, ●Lens Mount M12 ● IR Range I5: up to 50 m, ● Image Settings Rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser, ● Power Consumption and Current-12 VDC, 0.7 A, max. 7.5W PoE: (802.3af, 36V to 57V), 0.3 A to 0.2 A, max. 9W ● Camera out fitted with metal housing so as to prevent the lens from damages during physical abuse. (Make: Dahua/Panasonic) (Rate as per quotation enclosed)

Supply ,Testing and Commissioning of Dome Camera 8MP IR camera (rate as per Quotation)

Supply, Installation, Testing and Commissioning of 55" smart LED TV with following specifications a) Full HD 1920 x1080 (4K monitor) b) IPS panel c) Slim back light LED module d) 900 PMI e) Triple XD engine f) Dynamic scanning g) ANR h) True colour generator i) 8modes of picture j) picture wizardIII k) Real cinema 24P l) HDMI -3nos m) USB -3nos n) Built in LAN o) Magic remote p) Dimension 1242 x 724 x 55.1min(37). (Make: Sony/ LG /Samsung). (Rate as per quotation enclosed)

Supply and Clamping of CAT 6 armoured cable in suitable PVC Pipe 1" thick on wall / ceiling with connected PVC accessories with clamps, saddles etc., complete. (Between ethernet switch to camera and radio modem) i. Application : Primary (Campus), Secondary (Riser), Tertiary(Horizontal) IEEE 802.3 : 10Base-T; 100Base-T; 1000Base-T IEEE 802.5 16 MB; ISDN; TPDDI; ATM ii. Standards: ISO/IEC 11801 2nd ed.; IEC 61156-5 2nd EN 50173-1; EN 50288-6-1,EIA/TIA 568C.2, RoHS Compliant. Fire Rating: PVC : IEC 60332-1. iii. Conductor - Bare Copper Wire iv. Insulation - Polyethylene v. Twisting - 2 Cores to the pair vi. Cable lay up - 4 Core to the pair It has diameter of (23 AWG) 0.550 ± 0.015.Insulation : Polyethylene.GI wire of size is 0.90 ± 0.030mm.

Fixing and Termination of CAT 6 Cable RJ 45Jack Single Point ( Point to Point ) Crimping, Testing and arrangement charges.

Supply and fixing of POE 24 port switch 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 ̊C ~ +75 ̊C) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line.

Supply and fixing of POE 8 port switch 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 ̊C ~ +75 ̊C) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line. (Make: DLINK,NETGEAR/ TPLINK)

Supply and fixing of 2 feet CCTV Camera Stand with attachment fittings as follows: * Weather heads and couplings * Cabinet mounting fittings, plates, brackets as needed. * Reinforced couplings for wire entrances to cabinets.

Supply and Installation for 2KVA UPS with Battery, Single Phase UPS (Single Phase In & Single Phase Out) Capacity - System with Battery - 2Hours back up

Supply and Fixing of Rack with Accessories -Higher end 42 U Rack with LNS unit and fan extra for the above rack.

Supply and fixing of 6m Length pole with base plate of size 250x250x6mm as per IS-875 with following specification. Pole Outer die -76.10mm x 3.65mm Thick x 6 meter.

INDOOR & OUTDOOR LIGHTS

Supplying & Fixing of Brussel Lighting Poles 6m Height, 6 no.s of 50w LED using Base size of 139.7mm & Pole Dia OF 88.9mm Excluding the Foundation Cost

Supplying & Fixing of Merlin Lighting Poles 6m Heigh, Surface mounted with Base Size of 139.7mm & Pole Size of 88.9mm

Supplying & Fixing of Aston 3 Light Fixture including 3 No.s Of 60W LED pole mounted with Demnsion 342X135X325mm Luminous Flux 23398im Model No. KL-6798

Supply & Fixing of Sudo Mini-Asy Frame wall Recessed with 6W LED COD(mm) 124x83x70, Luminous Flux - 343iM Model No. KL-2747

Supplying & Fixing of Sleek Ajna Crescent Bollard Surface Mounter, 8W LED, Dimension 410X100Dia, Luminous Flux-117Im Model No. KL-5559

Supply & Fixing of Nebula Mini Spike Light with 6w LED, Dimension 101X90DiaX330 and Beam angle 15/25/40 Degress Model No. KL-4265

Supply & Fixing of Underwater Luminaire Surface mounting LED Spot Light , Surface Mounted with 3w Led Light, Dimension 106x70Diax134, Luminous Flux 133 Im, Beam angle 30Degree, 24v Series Waterproof IP67 Power Supply 144W RGB Controller with Remote kitt ( Model No. KL-6740)

Supply & fixing of Power Grazer-32, Surface Mounted with 20W/m LED , Dimension 1005X25X32, Luminous Flux - Upto 70Im/W, Beam Angle -30/60Degree and 24v Series Waterproof IP67 Power Supply ( Model No. k-lite KL-3557 )

Supply & Fixing of Female Connector Cable Model No. K-Lite KL-8321

Supply & Fixing of End Cap Model No.K-Lite KL- 8319

Supply & Fixing of Two way 3 Pin PG9 IP68 Connector Model No- K-Lite KL-4146

Supplying & Fixing of In-ground Luminaires recessed in ground with 9w led, Dimensio-116Diax153mm, Luminous Flux-429Im, Beam Angle 15/25/40 Degree Model No. K-Lite KL-4146

Supplying & Fixing of Form-17 Surace mounted 9W Led , Dimension 1010X17X9mm, Beam Anle 120Degree Model No. K-Lite KL-3256

Supply & Fixing of 24V Series Waterproof IP67 Power Supply suitable for KL-3557 Model no.s KL-8355

Supply & Fixing surface Mounted Bema7 12w LED, Dimension 123DiaX43mm Model No. K-Lite KL-3612

Supply & Fixing surface Mounted Bema7 12w LED, Dimension 123DiaX43mm Model No. K-Lite KL-3613

Supply & Fixing of Navi Spot Light Surface Mounted 30w Led, Dimension 329X166DiaX160mm, Beam Angle- 45Degree Model No. K-Lite- KL-4287

Supply,installation, testing and commissioning of 30W High efficiency ABS horn loudspeaker with weather protectin IP 65 Max Power : 45 W, Rated power, 30 Watts, Power tapping, 30/15/7.5W-Effective frequency range (-10 db) (-380 Hz to 5 kHz) - SPL at rated power (1 khz) 126 dB- Self extinguishing acc. to UL 94 VO - IP 65 acc. to IEC 60529, safety acc. to EN 60065. (Make - BOSCH)

Supply, installaion, testing and commissioning of 240W mixer amplifier with following features : inbuilt bluetooth for audio streaming, sports audio playback from USB pen drive, 4 microphone/line inputs, plus music source input, insert features to use as a pre/power amplifier, Optional 2 tone chime generation for input 1 technical specifications - Frequency response 80 Hz to 18 kHx (+1/-3 dB W - 10 dB ref. rated output) - Distortion <1% @ rated output power, 1 kHz bass control Max +/- 8 dB Treble control max +/- 8 dB. (Make - BOSCH)

Supply, installation, testing and commissioning of 480W Power amplifier in a 3U high housing with 70V / 100V and 8 Ohm outputs, Dual inputs with priority switching, 100V input for slave operating on 100V speaker line, Mains, battery backup, with following features -Output ower (rms) 480W, - Frequency response 60 Hz to 18 kHz (+1 / -3 dB at -10 dB ref rated output) - Distortion <1% @ rated output power, 1 kHz, - S/N (flat at max volume) > 90 dB - Batter power supply 24 VDC (Make BOSCH) (Market rate)

Supply and installation of Handheld microphone with a dynamic transducer element that shall be designed for high speech intelligivility. It should have a rugged enclosure is both stylish and easy to use in a wide range of public and sound reinforcement applications. Polar Pattern unidirectional, frequency range 80 hZ to 12 kHz, Sensitivity 1.7mV/Pa +/- dB, Rate out impedance 600 Ohms. (Make BOSCH) (Market rate)

Supply and laying of FRLS PVC insulated 2 core 1.5 sq.mm. Armoured Copper Cable on ceiling / wall using fixing accessories like screws, plug, clamps, etc., asper standard methods and as directed by the Departmental Officers.(SR-2023-24, pg-86, M-0773)

Supply & Installation of custom built M.S Powder coated wall mounting Audio rack with Lock & key for housing of Amplifier & Player / Recorder conforms to EIA-310,IEC-60297 and able to withstand the load of 40kg with welded construction made up of CRCA steel with suitable height, width and depth. (Market rate)

First Aid Box complete with all First Aid Medicines (M-1977)

Shock Treatment Chart fixed in glass frame (M-1978)

Fire Extinguisher Co2, 4.5 kg. confirming to TAC Norms (M-1982)

Supply and kept in position of 9 litres capacity Fire Buckets of 4 Nos. with Bucket Stand as per standard specifications and as directed by the Departmental Officers (SOR -2024-2025 ,pg 142, M-0842)

SOFTSCAPE WORKS

Nursery Establishment

Nursery Establishment of 500 Sqft as per arch drawings

Planting Soil Mixture

Supply & stacking of red earth at site to the departmental guage for pre-measurements which is of light textured, crystalline, porous and friable and not of generally acidic or neutral but not of alkaline and should be fertile, including seignior age charges,cost of transportation, loading, unloading, stacking and inclusive of all taxes etc., complete.

Supply of well decomposed Farm yard Manure in a powdery form, devoid of soil sand, stones, plastics and other materials, highly nutrient and which supports plant growth.

Supply and stacking of pit sand / earth filling sand at site to the departmental guage for premeasurements obtained from sand deposits and should clean whithout solid particles

Mixing charges of Red soil, sand and manure uniformly (1:1:1) for Preparation of soil mixture (excluding material cost)

Grasses

Planting of Cymbopogon citratus Plant foliage grass variety of height less than 30-45cm (1'-1'6") in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Cynadon dactylon including loading and unloading charges,transportation, stackingofsaplingsatsite,earthwork excavationof required size, plantingof sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Lemon grass Herbal plant variety of height 20-25 cm in polythene bag of size 6x7 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Vetiver Herbal plant variety of height 20- 25 cm in polythene bag of size 6x7 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site incharge.

Planting of Shade grass including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Ground Cover

Planting of Chlorophytum ornamental foliage Ground cover variety in polythene bag of dia 20 cm including loading and unloading charges, transportation, stacking of sapling at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Ophiopogon ornamental foliage Ground cover variety in Polythene bag of size 6x7 inch the rate including loading and unloading charges, transportation, stacking of sapling at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Portulaca ornamental foliage Groundcover variety in Polythene bag o fsiz e6x7 inch the rate including loading and unload ingcharges, transportation, stackingofsaplingatsite, earthworkexcavationof requiredsize, plantingof sapling, refilling of excavated earthetc as directedby the site in charge

Planting of Syngonium podophyllum ornamental foliage Groundcover variety in Polythene bag o fsiz e6x7 inch the rate including loading and unload ingcharges, transportation, stackingofsaplingatsite, earthworkexcavationof requiredsize, plantingof sapling, refilling of excavated earthetc as directedby the site in charge

Planting of Tradescantia ornamental foliage Ground cover variety in Polythene bag of size 6x7 inch the rate including loading and unloading charges, transportation, stacking of sapling at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Verbena foliage Ground cover variety in Polythene bag of size 6x7 inch the rate including loading and unloading charges, transportation, stacking of sapling at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Wedelia Trilobata foliage Ground cover variety in Polythene bag of size 6x7 inch the rate including loading and unloading charges, transportation, stacking of sapling at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Trees

Supplying and Planting of Bauhinia purpurea tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed bythe site in- charge.

Supplying and Planting of Mimusops elengi tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed bythe site in-charge.

Supplying and Planting of Nyctanthes arbor-tristis tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of sapling of Pongamia Pinnata height 240 – 300 cm in polythene bag including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in -charge.

Supplying and Planting of Albizia lebbeck tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed bythe site in- charge.

Supplying and Planting of Azadirachta indica tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed bythe site in- charge.

Supplying and Planting of Barringtonia acutangula tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed bythe site in- charge.

Supplying and Planting of Butea monosperma tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed bythe site in- charge.

Supplying and Planting of Callophyllum inophyllum tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed bythe site in- charge.

Supplying and Planting of Cassia fistula tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed bythe site in- charge.

Supplying and Planting of Madhuca longifolia tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed bythe site in- charge.

Supplying and Planting of Lagerstroemia indica tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed bythe site in- charge.

Shrubs

Planting of Alpinia purpurata Plant foliage shrub variety of height 60-91cm (2'-3') in a polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site

Planting of Aspidistra elatior Plant foliage shrub variety of height 30-60cm (1'-2') in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Calendula officinalis (yellow) Plant foliage shrub variety of height 30-60cm (1'-2') in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Cosmos sulphureus (yellow) Plant foliage shrub variety of height less than 60-900cm (2'-3') in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Crossandra infundibuliformis Plant foliage shrub variety of height 60-90cm (2'-3') in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Plumbago auriculata Plant foliage shrub variety of height 60-75cm (2'-2'6") in polythene bag of including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Zinnia elegans (orange) Plant foliage shrub variety of height 60-75cm (2'-2'6") in polythene bag of including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Begonia Plant foliage grass variety of height less than 23cm (9") in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Canna Indica Plant foliage shrub variety of height less than 60-900cm (2'-3') in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Galphimia Gracillius Plant foliage shrub variety of height less than 60-900cm (2'-3') in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Grewia asiatica Plant foliage shrub variety of height 60-90cm (2'-3') in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Heliconia collinsiana/ schiedeana plant variety of height 60-90cm (2'-3') in polythene bag of dia 60 cm including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in -charge.

Supplying and Planting of Heliconia Rostrata plant variety of height 60-90cm (2'-3') in polythene bag of dia 60 cm including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in -charge.

Supplying and Planting of Hemelia Pattens plant variety of height 60-90cm (2'-3') in polythene bag of dia 60 cm including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in -charge.

Planting of Lawsonia Inermis Plant foliage shrub variety of height 60-75cm (2-2'6") in polythene bag of including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Murraya Paniculata Plant foliage shrub variety of height75-90cm (2'6"-3') in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Nerium Oleander Pink Plant foliage shrub variety of height 75-90cm (2'6"-3') in polythene bag of including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Nerium Oleander White Plant foliage shrub variety of height 75-90cm (2'6"-3') in polythene bag of including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Pandanus amaryllifolius Plant foliage shrub variety of height 60-75cm (2'-2'6") in polythene bag of including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Russelia equisetiformis Plant foliage shrub variety of 60-75cm (2'-2'6") in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Schefflera Arboricola Plant foliage shrub variety of height less than 30cm (1') in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Senna Ariculata plant variety of height 60-75cm (2'-2'6") in polythene bag of dia 60 cm including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in -charge.

Planting of Tabernaemontana divaricata Plant foliage grass variety of height less than 30cm (1') in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Vitex Negundo Plant foliage grass variety of height less than 15cm (6") in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Herbs

Planting of Chlorophytum comosum Plant foliage shrub variety of height 30-45cm (1'-1'6") in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Dianella ensifolia Plant foliage shrub variety of height 30-45cm (1'-1'6") in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Mimosa pudica Plant foliage shrub variety of height 30-60cm (1'-2') in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Ophiopogon japonicus Plant foliage shrub variety of height less than 30cm (1') in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Tradescantia spathacea Plant foliage shrub variety of height less than 30cm (1') in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Caladium Plant foliage shrub variety of height 15-23cm (6"-9") in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Coelus Plant foliage shrub variety of30-45cm (1'-1'6") in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Colocasia esculenta Plant foliage shrub variety of height 23cm (9") in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Eclipta Prostrata Plant foliage shrub variety of height 15cm (6") in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Hygrophilia Auriculata Plant foliage shrub variety of height 7-15cm (3"-6") in polythene bag of including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Hymenocallis speciosa Plant foliage shrub variety of height 30-45cm (1'-1'6") in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the sitein-charge.

Planting of Ocimum basilicum Plant foliage shrub variety of height less than 30cm (1') in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Spathiphyllum wallisii Plant foliage shrub variety of height less than 30cm (1') in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Vinca Rosea Plant foliage shrub variety of height less than 30cm (1') in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Grasses

Planting of Bambusa Ventricosa Plant foliage grass variety of height less than 30-45cm (1'-1'6") in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Pennisetum Rubrum Plant foliage grass variety of height less than 30-45cm (1'-1'6") in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Pennisetum Setaceum Plant foliage grass variety of height less than 30-45cm (1'-1'6") in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Saccharum Spontaneum Plant foliage grass variety of height less than 30-45cm (1'-1'6") in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Creeper

Planting of Clitoria Ternatea Plant foliage grass variety of height less than 150cm (5') in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Philodendron Gloriosum Plant foliage grass variety of height less than 45cm (1'6") in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Aquatic Plants

Planting of Nelumbo nucifera (Lotus) Aquatic Plant foliage variety of height 15cm (6") in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Nymphaeaceae (Water lily) Aquatic Plant foliage variety of height 15cm (6") in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Acorus calamus Plant foliage shrub variety of height 23cm (9") in a polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Cyperus alternifolius Plant foliage shrub variety of height 23cm (9") in polythene bag including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

M/s. SBR CONSTRUCTION (BID ID -1099757)

M VENKATESHBABU (BID ID -1101202)