PROVN OF SPL REPAIR TO BLDG NO P167 INCLUDING REWIRING OF BLDG AT MIL STN BIKANER

Amount

Dismantling of Roof tiles of any description or thickness in floor, roof, apron etc laid, bedded and pointed in any mortar complete.

Demolition of lime concrete of any description over roof slab complete all as specified by Engineer-in-Charge.

M & L for 10 mm thick screeding in cement mortar 1:6 on concrete surfaces, finished fair & even including mixing water proofing compound as per manufacturer's instructions complete. (WPC shall be measured separately as supply only) all as specified.

Supply only liquid water proofing compound ISI Mark complete. Make: Dr. Fixit or Equivalent.

M&L applying priming coat of cold bitumen primer at the rate of 0.40 Ltrs per Sqm as per para 11.44.5 of MES SSR Part-I incl cleaning and preparing the surface complete all as specified.

M & L APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. Not less than 150 gms/sqm) land on primed surfaces by forced application complete all as specified.

M & L for lime concrete terracing as on roof with mimimum thickness of edge 40 mm and increasing uniformly towards ridge to obtain a certain chain slope of (1:40) as described in para 11.27.2 of MES SSR part-I complete all as specified. NOTE:- For lime concrete, mudia kankar (source : NAL) and Kolayat coarse sand in lieu of brick aggregates and Surkhi respectively as specified in MES schedule Part-I shall be used.

M & L for 40 mm thick brunt clay brick tiles bedded on cement mortar and joints grouted flush in cement and sand mortar (1:3) mixed with integral water proofing compound IS 2645 : 2003 @ 3% by wt of cement as Complete all as specified and as directed..

ditto complete all as per Item No 8 above but except tiles complete all as specified.

Dismantling floor, hearth or wall tiling any type including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the primises Complete.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified.

M & L for coloured Non skid ceramic tiles 7 to 8 mm thick (squar/ rectangular) area of each tiles exc 0.11 Sqm but n.exc 0.18 Sqm in floor etc. set and jointed in neat cement slurry and pointed in coloured cement to match the floor laid over 15mm thick screed bed in cement mortar 1:6 complete all as specified.

M & L for coloured Glazed ceramic tiles 450mm x 350mm x 7mm or 300mm x 450mm x 7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match the floor as on vertical surfaces laid over 10 mm thick cement plaster in 1:4 complete all as specified.

M & L for 25 mm thick Cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate in floors to receive finished even and smooth using extra cement complete all as specified.

M & L for 20-25 mm thick Machine cut Kota stone slab flooring laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing (Mirror polish) and Wax polishing including laid over 20 mm thick screed bed in cement mortar 1:4 complete all as specified.

M & L for 20-25 mm thick Machine cut Kota stone in riser to steps, skirting, dado and pillar etc on vertical surfaces laid over 10 mm thick cement plaster in 1:4 (Rubbed and mirror polished) complete all as specified.

Demolition of reinforcement concrete of any description and in any position not otherwise specifically provided for concrete complete all as specified and directed.

M & L for M-25 (Design mix) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

M & L for Mild steel TMT bars 10mm dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M & L for 20 mm thick granite (of any tpe) work (table rubbed and polished) in steps, jambs, pillars, windowcills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified.

Rounding to edges of stone slabs one edges such as in steps, cooking platform and other similar situations complete all as specified.

Taking down shutter of any description exc. 1 Sqm but not exc.2 Sqm each and refixing in the same opening after necessary easing, repairs, adjustment etc. complete all as specified.

Taking down chowkhats or frames not exc. 1.50 Sqm each but with shutter (with out taking of shutter from the frame ) and making good the surface of walls as per existing with cement mortar complete.

Taking down chowkhats or frames exc. 1.50 Sqm each but n.exc 4 Sqm with shutter (with out taking of shutter from the frame ) and making good the surface of walls as per existing with cement mortar complete all as specified.

Taking down shutter of any description exc. 1sqm but not exc.2 sqm each complete all as specified.

S & F for pressed steel frames of size 125 x 60 mm with one or more rebates including necessary fixing lugs hinges, locks trike plate etc (thickness of sheet shall be 1.25mm) and making good the plaster of wall in CM 1:6 complete all as specified.

S & F for pressed steel frames of size 105 x 60 mm with one or more rebates including necessary fixing lugs hinges, locks strike plate etc (thickness of sheet shall be 1.25mm) and making good the plaster of wall in CM 1:6 complete all specified.

Cutting holes in brick walls in cement mortar exc half brick but not exc one brick for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required all as specified.

S & F for bands, straps, supports or stays for rain water, ventilating pipes, including bolts, if required, hooks and pintal hinges, large hasp and stapals, chains hand made sliding bolts, clamps, hold fast,wall ties, hooks for hanging fans, plain angle cleats for securing purlins to woods trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articals conforming to Fe 290 Gde-E-165 complete all as specified.

M & L for PCC 1:3:6 type C-1 (using 20mm Graded Stone Aggregate) as in fixing Holdfast, Plinth courses, bed plates, string courses, coping, filling of chowkhats etc., complete all as specified and as directed by Engr-in-Charge.

S & F 2nd class HW 35mm thick factory made panelled shutters with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS-1003 (Pt-I) kiln seasoned and chemically pressure treated.

S & F 2nd class HW 35mm thick glazed and skeleton shutters open rebated and prepared to receive glass gauge etc (w/o sash bars) complete all as specified.

M&L Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as specified and approved.

M&L factory made solid panel PVC door shutter with MS square tube 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC sheet stirip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top,lock and bottom rail on either side & as gap insert for top rail & bottom rail .panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement S&F in the steel frame at site as per specification.

S & F rubber gasket of thickness atleast 2.5 mm and width 60 mm for wooden doors to cover to gap between door and floor etc complete all as spd and directed by Engr-in-Charge.

S & F for box type steel ventilators with two top hung shutter (One with pin headed glass pane and other with wiremess) and at bottom segment fixed with pin headed glass including hinges, steel peg stay complete all as specified. Note: - Glass pane and wiremesh shall be measured and paid separately.

S & F for steel window with side hung shutter including box type hinges with steel handle of MS flat 25x5mm and 2nos tower bolt of 100mm long fixed to shutter complete with glazing bar dovtailed or welded including one shop coat of primer complete all as specified.

S & F for steel window with side hung shutter incl.box type hinges with steel handle of MS flat 25x5mm and 2nos tower bolt of 100mm long fixed to shutter complete w/o glazing bar dovetailed or welded including one shop coat of primer complete all as specified.

M & L stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified.

M & L stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples fixed in repairs complete all as specified.

S & F for 100 mm long Aluminium anodised Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified.

S & F for 150 mm long, aluminium, anodised, barrel tower bolts of extruded section complete all as specified.

S & F for 150 mm size aluminium handles, cast type, anodised complete all as specified.

S & F for 100mm size butt hinges, medium weight cold rolled mild steel complete all as specified.

S&F in repair stainless steel peg set of 6 hooks each complete all as directed.

S & F for 300 mm, ordinary rat tail rod pattern springs of mild steel including roller and roller plate complete all as specified.

S & F for 250mm long aluminum alloy anodized sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy complete all as specified.

M & L for complete removal of existing treatment on wooden surfaces any description over 10cm in width or girth and applying two coats of synthetic enamel paint incl preparation of surfaces over and incl a coat of pink primer & preparing with wooden putty etc complete all as specied and directed.

M & L for preparing new surface of wood of any desc over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M & L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as spd.

M & L preparation of old steel surfaces of any description, over 10 cm in width or girth, and applying one coat of synthetic enamel paint incl preparation all as specified.

S & F for 3mm thick sheet glass, ordinary quality and glazing with oil putty in squares n. exc 0.5 Sqm in each pane incl hacking out old glass panes complete all as specified.

S & F for 4mm thick pin headed sheet glass, ordinary quality and glazing with oil putty in squares n. exc 0.5 Sqm in each pane complete all as specified.

Demolition of brick work or stone boulder masonary of any description in and any position built in cement mortar or cement lime mortar complete.

M&L brick wk with Fly ash bricks (old sized bricks), straight or curved on plan exc 6 m mean radius built in CM 1:4 for manholes complete all as specified

M & L Brick work with fly ash bricks (Half brick), straight or curved on plan exc. 6 m mean radius built in CM 1:4 complete all as specified.

Taking up or down 15mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete.

S & F GI tubing 15mm dia medium grade with all fittings and fixed to wall, floor and ceiling etc complete all as specified.

Fixing only of old steel GI tubing, 15mm bore and connections in new or old position (walls, ceiling, floors etc) complete

Taking up or down 20mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete.

S & F for GI tubing 20mm dia medium grade with all fittings and fixed to wall, floor and ceiling etc complete all as specified.

Fixing only of old steel GI tubing, 20mm bore and connections in new or old position (walls, ceiling, floors etc) complete all as specified.

Taking up or down 25 mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified.

S & F for GI tubing 25 mm dia medium grade with all fittings and fixed to wall, floor and ceiling etc complete all as specified.

Fixing only of old steel GI tubing, 25 mm bore and connections in new or old position (walls, ceiling, floors etc) complete all as specified.

Taking up or down 40 mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified.

S & F for GI tubing 40 mm dia medium grade with all fittings and fixed to wall, floor and ceiling etc complete all as specified.

Fixing only of old steel GI tubing, 40 mm bore and connections in new or old position (walls, ceiling, floors etc) complete all as specified.

Taking up or down 50 mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified.

S & F for GI tubing 50 mm dia medium grade with all fittings and fixed to wall, floor and ceiling etc complete all as specified.

Fixing only of old steel GI tubing, 50 mm bore and connections in new or old position (walls, ceiling, floors etc) complete all as specified.

S & F as in repair, 15 mm bib taps, brass, chromium plated, fancy type, long nose, with capstan head handle screwed down high pressure, including CP brass wall flanges; screwed for 15mm bore pipe connection complete all as specified.

S & F as in repair, 15 mm pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified.

S & F as in repair, 15 mm angle valve, brass, chromium plated, fancy type, with capstan head handle screwed down high pressure, including CP brass wall flanges; screwed for iron pipe connection complete.

S & F for Health faucet, brass, chromium plated, heavy duty, including flexible pipe suitable for 15mm bore water connection; for EWC fixed in repair Complete.

S & F for Shower rose, round type brass, chromium plated, 140mm dia with or without swivel joint, with & including CP brass arm and wall flange, fixing to steel pipe or union as in repair complete.

S & F Soap dish, brass, chromium plated, heavy duty, fixed to wall with plugs with brass cadmium plated screws, fixed in repair complete all as specified.

S & F tubular towel rails, brass, chromium plated, heavy duty, D-type, 20mm dia & 60cm long between flanges fixed in repair complete all as specified.

S & F as in repair, gun-metal, of 20 mm globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified.

S & F as in repair, gun-metal, of 25 mm globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified.

Dismantling water tanks upto 1000 ltr cap and removing to store.

S & F two layer ISI marked rotational moulded polythylene water storage tanks tripple layer Black in colour (cylindrical vertical with closed top) of 1000 litres capacity, hoisted and fixing in position including connecting up pipes complete all as specified.

S & F 20 mm ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/40mm- 690 gms/50mm-1240 gms) all as specified.

S & F as in repair, PVC flexible connections 450mm long 15mm dia with brass flange nuts & washers complete. Make: Prayag/Polytuf or equivalent as approved by Engr-in-Charge.

S & F as in repair, 75 mm dia CI floor trap including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified.

S & F stainless steel grating suitable for 100 mm dia bore fixed with white cement with outer square frame, complete all as specified as directed by Engineer-in-charge .

S & F stainless steel grating suitable for 100 mm dia bore with hole fixed with white cement with outer square frame, complete all as specified as directed by Engineer-in-charge .

Demolition in concrete of any description and in any position not otherwise specifically provided.

M & L for 75mm thick PCC 1:3:6 C2 using 40 mm graded stone aggregate as in plinth protection laid in panels and finished even and smooth without using extra cement complete all as specied and directed.

M & L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in filling in sunken portion complete all as specified.

M & L rendering 10 mm thick wall plaster in CM 1:3 even & smooth without using extra cement complete all as specified and directed.

M & L for applying a layer of hot blown bitumen of 85/25 penetration grade @ 1.20 Kg/Sqm incl cleaning the surface of roof or sunken etc complete all as specified.

M & L for polythene film, 150 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sq. m all as specified.

Dismantling and disconnecting of existing CI soil vent pipe upto 100 mm bore fixed to wall,laid in trenches incl all fittings & accessories.

S & F 100 mm dia (Spun pipes) Cast Iron soil waste & vent pipes in any length with or without ears, with cement joints laid in trenches or in floors.

S & F 100mm dia Cast Iron soil waste & vent pipes in any length with or without ears, with cement joints but fixed to walls with & including fixing clamps.

-do- but except pipes

Dismantling and disconnecting of existing CI soil vent pipe upto 75 mm bore fixed to wall,laid in trenches incl all fittings & accessories.

S & F 75mm (Spun pipes) dia Cast Iron soil waste & vent pipes in any length with or without ears, with cement joints laid in trenches or in floors.

S & F 75mm dia Cast Iron soil waste & vent pipes in any length with or without ears, with cement joints but fixed to walls with & including fixing clamps

-do- but except pipes

Dismantling and disconnecting of existing CI soil vent pipe 50 mm bore fixed to wall,laid in trenches incl all fittings & accessories.

S & F 50 mm (Spun pipes) dia Cast Iron soil waste & vent pipes in any length with or without ears, with cement joints but fixed to walls with & including fixing clamps

-do- but except pipes

Extra over cast iron pipe and fittings if lead joint is provided in lieu of cement joint for 75 mm pipe.

Extra over cast iron pipe and fittings if lead joint is provided in lieu of cement joint for 100 mm pipe.

S & F in repairs 100 mm dia branch piece single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door all as specified.

S & F in repairs 75 dia branch piece single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door all as specified.

S&F in repairs 75 mm bore CI bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified.

S&F in repairs 75 mm bore CI bends (any radius), diminishing pieces or tapers (larger bore measured) without oval access door complete all as specified.

S & F in repairs 100 mm bore CI bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified.

S & F in repairs 100 mm bore CI bends (any radius), diminishing pieces or tapers (larger bore measured) without oval access door complete all as specified.

S & F in repairs 100 mm bore CI tee (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified.

S & F in repairs, 100 mm CI bends (any radius) with duck's foot or heel rest complete all as specified.

S & F as in repair, 100 mm cast iron sanitary connection socket in fit WC out-let complete all as specified.

S & F for cast iron vent cowls 100 mm dia complete all as specified.

S & F for cast iron vent cowls 50 mm dia complete all as specified.

S & F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays. Including bolts and nuts and securing ends of stays to wall or roof for 50 mm bore all as specified.

S & F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays. Including bolts and nuts and securing ends of stays to wall or roof 75 mm bore all as specified.

S & F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays. Including bolts and nuts and securing ends of stays to wall or roof 100 mm bore all as specified.

Taking down PVC pipes and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc.,including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fitting and accessories)

S & F for PVC (SWR) 100 mm dia single socket in any length with rubber ring joints fixed to wall incl SS clamp complete all as specified.

S & F for PVC (SWR) 100 mm dia bend of any radius fixed to wall Complete.

S & F for PVC (SWR) 75 mm dia single socket in any length with rubber ring joints fixed to wall incl SS clamp complete all as specified.

S & F for PVC (SWR) 75 mm dia bend of any radius fixed to wall complete all as specified.

M & L for vitreous china wash down water closet (pedestal pattern) complete, including connection to drain pipe and to flushing pipe antisyphonage pipe etc white / ivory in colour, fixed in repair, complete all as specified and as directed.

S & F Plastic water closet seat WHITE COLOUR closed pattern with flat bottom and cover and mild steel chromium plated hinging devised fixed Complete.

S & F in repair Vitreous china wash hand basin, white, oval shape including 32mm dia CP brass waste coupling, 32mm dia PVC waste pipe, cast iron brackets and making good disturbed surfaces in cement mortar 1:3 or PCC 1:2:4 complete all as specified.

M & L for vitreous china squatting pan of Orissa patten of size 580 x 440mm white, back inlet with integral foot rests including connection to trap and to flushing pipe, anti-syphonage pipe etc, fixed in repair complete and making good to floor in cement mortar 1:3 incl S & F trap for pan complete all as directed and specified.

S & F PVC valve less, syphonic action type, fluhsing cistern, 10 ltrs capacity, low level, white, with inlet, ball valve, float and handle including 32mm bore PVC flushing pipe, brackets and fixed in repairs including taking down existing flushing cistern of any description complete all as specified.

Taking down cement plaster/terrazo finish on brick or stone walll etc including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed

M & L for 10mm thick Rendering in cement mortar 1: 6 on fair faces of brick work or concrete surfaces, finished even & smooth without using extra cement complete all as specied and directed.

M & L for 15mm thick Rendering in cement mortar 1: 4 on fair faces of brick work or concrete surfaces,incl water proofing liquid finished even & smooth without using extra cement complete all as specied and directed.

M & L for 5 mm thick Rendering in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specied and directed.

M & L for rendering 10mm thick in cm 1:4 as setting coat and 5 mm thick in cm (1:4) as finishing coat as in chajja with WPC. Note: - WPC should be measured and paid separately.

M & L for preparing new plastered or unplastered surfaces of walls and applying two coats of cement base paint over & incl a coat of primer complete all as specified and directed.

M & L for preparing new plastered or unplastered surfaces of ceiling and applying two coats of OBD over a coat of primer complete all as specified.

M & L for preparing new plastered or surfaces of walls and applying two coats of distemper oil emulsion, white or tinted over & incl a coat of primer over & incl 3mm thick Birla white putty complete all as specified.

M & L for preparation of old surfaces by complete removal of existing treatment of walls incl paillars etc. by mechanical equipment like electric wall sander and applying two coats of oil bound distemper using rollers over a coat of primer incl a layer of wall care putty complete all as specified and as directed by Engr-in-Charge.

M & L for preparing old decorated plastered or unplastered surfaces of walls and applying two coat of white wash complete all as specified and directed.

M & L for removing existing treatment completely and applying two coat of cement base paint over a coat of primer incl preparation of existing surfaces of wall complete all as specified and directed.

M & L for preparing old decorated plastered or unplastered surfaces of walls and applying two coat of cement base paint complete all as specified and directed.

M & L for washing, rubbing down and stopping of distempered and painted surfaces old decorated plastered or unplastered surfaces of ceiling and applying two coat of white wash complete all as specified and directed.

M & L for washing, rubbing down and stopping of distempered and painted surfaces old decorated plastered or unplastered surfaces of ceiling and applying two coat of OBD complete all as specified and directed.

S & F for mild steel window handles, left or right size 150mm complete all as specified.

S & F for mild steel window stay of size 250mm complete all as specified.

Removing building materals etc., (other than spoil payable under items 99 to 102 in Section 3-Earthwork) to a distance 5 km or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination all as specified.

Cutting chases, pining in, making good to facings where required and pointing in cement mortar 1:3, for concealed water tubing etc and maing good, cutting exc 10cm and not exc 20 cm girth complete all as specified.

M & L for running welding to stair case railing exceeding 6mm but not exceeding 9mm thick complete all as sepcified.

S & F in repairs, Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) with spreader and urinal waste pipe complete all as specified.

M & L for framed brackets of angles cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, alongwith anchor bolt of length 150 mm long and not less than 10 mm diametre conforming to Fe 410-0 or Fe 310-0 all as specified.

S & F SFRC (Steel fibre reinforced concrete) cover and frame (Light duty) grade designation) of 560 mm dia of cover with frame conferming to IS 12592, fixed in cement cocrete 1:2:4 making good the surface all as specified.

M & L for concrete bed for 150 mm drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in 1:3:6 type C-2 all as specified.

M & L for 150 mm bore salt-glazed stoneware drain pipes laid in trenches and jointed as specfified.

M & L for cast iron gully traps, square or round mouthed, type `P' of size 100 x 100 complete all as specified.

Forming jambs, etc. in CM 1:4, to openings (to foregoing item), with stone supplied by MES including cutting, toothings and properly bonding into old work, including facing and pointing (if necessary) to match existing work, complete

Taking down carefully (aluminium) point wiring complete of any type (batten/ surface conduit or concealed) for light point, fan point, bell point socket point or power point complete with all fitting such as switches, sockets pendants, ceiling rose, round block etc complete and making good disturbed surfaces of wall, floor or ceiling with plaster of tiles or roof treatment etc and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete all as spcified and directed.

Taking down submain wiring Aluminium/ copper of any size including earth continuity condutor on teak wood or conduit and removing from site and making good the disturbed surface of wall etc complete all as specified and directed.

Taking down old U/S existing DB TPN 4 way and DB SPN 8 way including MCB/MCCB of any capacity and any size and removing from site and making good the disturbed surface of wall etc complete all as specified and as directed.

M & L for point wiring with and including single core FRLSH PVC insulated and unsheathed stranded copper conductor cable of size 1.5 sqmm 1100 volts grade drawn through and including suitable size of PVC concealed conduit with accessories with laminated top cover fixed on MS sunken box for housing of switch, socket, regulator etc complete with and including 1.5 sqmm FRLSH PVC insulated and unsheathed stranded copper conductor cable as earth wire and connected to common earth dolly and making good to the disturbed surfaces of wall, floor, ceiling etc to match with exisiting surface complete all as specified and as directed by Engr-in-Charge for the following :-(a) One Light/fan/exaust fan point controlled by one switch.

(b) One 3 pin 5 amps socket on independent board.

all as per item No 161 above but with 2.5 sqmm copper wire for 3 pin socket outlet 15 Amp on independent board complete and all as directed by Engr-in-charge.

S&F switch piano type, 5 Amp, single pole one way, 230 Volts, flush type complete all as specified and as directed by Engr- in -charge.

M&L Switch piano flush type single pole, one way 15 Amps 230 Volts complete all as specified & directed by Engr-in-Charge.

M&L socket outlet 3Pin, 5 Amps flush type 230 Volts complete all as specified and directed by Engr-in-Charge.

M&L for socket outlet 2 in 1, 3 Pin, 5 & 15 Amps, 230 Volts t complete all as specified & directed by Engr-in-Charge.

S&F ceiling rose, surface backelite , three terminal AC, 230 volt complete all as specified.

supply and fixing fan regulator electronic socket type five step controlled 230V AC 50 Hz for complete all as specified and directed by Engr-In-Charge.

S&F LED tube light fitting, 1x 20-22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Make : Philips-BN021 LED 20S PSU CW GR S2/ Crompton Greaves LDDR20-CDL Dazzle Ray / bajaj-BCLAB 20W

M & L Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 5watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

S&F sheet metal enclosure MCB DB, double door, vertical TPN 4 way with 200 Amps rated busbar all as specified and as directed. Make:- Hegar/Legrand/Seimens

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

S & F double door, sheet metal enclosure, powder coated for MCB DB SPN 8 way fitted with neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to IS 13032-1991 complete all as specified and as directed by Engr-in-charge.

S & F MCB SPN, 5-32 Amps, 240 volts, breaking capacity 16KA complete all as specified and as dircted by Engr-in-charge.

S & F MCB SP, 5-32 Amps , 240 volts, breaking capacity 10KA complete all as specified and as dircted by Engr-in-charge.

S&F MCCB 63 amps, 4 pole, 415 volts, fixed type breaking capacity 16KA complete all as specified and as directed by Engr-in-charge.

M&L for submain wiring using 4 runs of single core FRLS PVC insulated, unsheathed stranded copper conductor cable of size 4runs of 6 Sqmm of voltage rating 1100V for three phase & neutral, drawn in and including concealed PVC conduit of dia not less than 25 mm dia with standard acessories, along with two run of FRLS PVC insulated, unsheathed, stranded copper conductor of size 2x 6.0 Sqmm as earth continuity conductor all as specified and directed(Note-4 runs of single core FRLS PVC cable 6sqmm for three phase & neutral with Two run of earth conductor as earth and conduit shall be measured as one unit)

M & L for submain (single phase) wiring complete with and including 4.0 sqmm two single core, fire retardant, PVC insulated and unsheathed multistranded copper conductor cable, 1100 Volts grade, drawn through PVC conduit of suitable size including accessories and fixed on walls and 2.5 sqmm, fire retardant, PVC insulated, multistranded copper conductor cable for earthing and connected to common earth dolly complete all as specified and as directed by Engr-in-Charge. Note :- (i) Two runs of 4.0 sqmm PVC insulated wire and one run of 2.5 sqmm wire and one run of PVC conduit shall be measured as one unit length. (For MCB DB SPN Circuit)

Taking down fan,sealing cable end,dismantling blades and removing fan and blades & refixing ceiling fan of any make, any sweep , keeping side in store in safe custody for painting of ceiling fan complete,in situ with synthetic enamel paint by spraying including filling cavities with filler,one coat after cleaning all dust and reassembling the fan complete including writing MES No at the site.

Taking down Exhaust fan,sealing cable end,dismantling blades and removing fan and blades & refixing Exhaust fan of any make, any sweep , keeping side in store in safe custody for painting of Exhaust fan complete,in situ with synthetic enamel paint byspraying including filling cavities with filler,one coat after cleaning all dust and reassembling the fan complete including writing MES No at the site.

M&L for Earthing complete with galvanized steel earth plate electrode 60cm x60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level connecting to the galvanised earth lead wire 4.0 mm dia by means of bolts, nuts check nuts and washers of galvanized iron and steel earth wire protected by provision of GI mediumgrade pipe 15mm bore including provision of concrete pit made with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4Kg/Sqm) and frame of angle iron 40x 40x6 mm and handle of 6mm dia MS bar made to shape, GI light grade 20mm bore pipe for watering perforated at bottom, 1.75meter long placed on top edge of earth plate, common salt & charcoal filling with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returing filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate No -5 of SSR 2009 Part-I and connecting to Lighting protection earth test points all as specifed and directed including testing on completion.

Supply, laying in trenches, connecting and testing LT UG cable, XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25sqmm x 4 core all as specified and directed.

Excavation in trenches n. exc 1.5 m in depth and not exc 1.5 m wide for laying of GI tubes etc and getting out in soft/ dense soil complete all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

Removing excavated soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5 above the starting point complete all as specified and as directed by Engr-in-charge.

Supply, laying and jointing GI tubes, medium grade 50mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in trenches/wall complete all as specified and directed by Engr-in-charge

Supply, laying and jointing GI tubes, medium grade40mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in trenches/wall complete all as specified and directed by Engr-in-charge .

Supply, laying and jointing GI tubes, medium grade 25mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in trenches/wall complete all as specified and directed by Engr-in-charge .

Cutting existing steel tubing for alterations or additions done in position without taking down for 50mm dia pipe (Each cut measured)

S&F Gun metal gate valve 50mm bore with iron wheel head screwed both ends for iron pipes complete all as specified and directed

S&F Gun metal gate valve 40 mm bore with iron wheel head screwed both ends for iron pipes complete all as specified and directed

S&F Gun metal gate valve 25mm bore with iron wheel head screwed both ends for iron pipes complete all as specified and directed .

N.K. CONSTRUCTION COMPANY

SUBHAM ENTERPRISES

JAGDAMBA CONSTRUCTION COMPANY