Loading…
Loading…
Tender Value
₹1.5 Cr
EMD Value
₹3.1 L
Closing Date
8 May 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
WORKSOL
19 conditions · 8 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less, where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure- VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
a)The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender .
b) (1) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of dvertised value of each component of tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note for b(1): Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components. (b)(2)In such cases, what constitutes a component in a composite work shall be clearly pre-defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract. Note: for subletting of work costing up to Rs 50 lakh, no previous work experience of subcontractor shall be asked for by the Railway.
In case after award of contract or during execution of work it becomes necessary for contractor to change subcontractor, the same shall be done with subcontractor(s) fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract, with prior approval of Chief Engineer in writing.
Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates.
In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
Definition of Similar Work: - Any Signaling or Telecom work.
29 conditions · 14 needing a document upload
Please submit your bank details i.e. Name of the Bank along with Bank Branch Code, Account Number, IFSC Code, and PAN Number.
Please furnish list of plant and Machinery available on hand own and proposed to be inducted own and hired to be given separately for the subject work.
Please furnish list of Works on hand indicating Description of Work, Contract Value, Approximate value of balance work yet to be done and Date of award.
Please furnish list of Works completed in last seven financial years giving Description of Work, Organization for whom executed, approximate value of contract at time of award, Date of award and Date of Completion. Date of actual Start, Actual Completion and Final value of Contract shall also be given.
Please furnish list of personal, organization available on hand and proposed to be engaged for the subject work.
Documents to be Submitted Along with Tender: (i)The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society / Registered Trust / HUF etc. The tenderer(s) shall enclose the attested copies of the constitution of their concern, and copy of PAN Card along with their tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be. (ii)Following documents shall be submitted by the tenderer:
(a)Sole Proprietorship Firm: All documents in terms of Para 10 of the Tender Form (Second Sheet) above (As per GCC-2022).
(b)HUF: i) A copy of notarized affidavit on Stamp Paper declaring that he who is submitting the tender on behalf of HUF is in the position of 'Karta' of Hindu Undivided Family (HUF) and he has the authority, power and consent given by other members to act on behalf of HUF. (ii) All other documents in terms of Para 10 of the Tender Form (Second Sheet) above.as per GCC-2022.
(c)Partnership Firm: All documents as mentioned in para18 of the Tender Form (Second Sheet) as per GCC-2022.
d) Joint Venture (JV): All documents as mentioned in para 17 of the Tender Form (Second Sheet).as per GCC-2022.
(e)Company registered under Companies Act2013: (i) The copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company (ii) A copy of Certificate of Incorporation (iii) A copy of Authorization/Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company. (iv) All other documents in terms Para 10 of the Tender Form (Second Sheet) above.(Eligibility Criteria) above as per GCC-2022.
(f)(i) A copy of LLP Agreement (ii) A copy of Certificate of Incorporation (iii) A copy of Power of Attorney/Authorization issued by the LLP in favour of the individual to sign the tender on behalf of the LLP and create liability against the LLP. (iv) An undertaking by all partners of the LLP that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP or JV in which they were / are partners/members. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the Standard General Conditions of Contract. (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet)..(Eligibility Criteria) above as per GCC2022.
(g)Registered Society & Registered Trust: (i) A copy of Certificate of Registration (ii) A copy of Memorandum of Association of Society/Trust Deed (iii) A copy of Power of Attorney in favour of the individual to sign the tender documents and create liability against the Society/Trust. (iv) A copy of Rules & Regulations of the Society (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet) above.
The tenderer whether sole proprietor/ a company or a partnership firm/registered society / registered trust / HUF / LLP etc if they want to act through agent or individual partner(s), should submit along with the tender, a copy of power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, specifically authorizing him/them to sign the tender, submit the tender and further to deal with the Tender/ Contract up to the stage of signing the agreement except in case where such specific person is authorized for above purposes through a provision made in the partnership deed / Memorandum of Understanding / Article of Association /Board resolution, failing which tender shall be summarily rejected.
Any DIPP certificate submitted along with the tender document for, exemption of EMD should be valid on the date of opening of the tender, else the tender offer will be summarily rejected.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
The tenderers may also upload the following documents along with his/their tender: The tenderer may upload statement, which shall contain organizational set up and working systems to be adopted by the successful tenderer s during the operation of the contract. It shall contain the details of man power and machineries in the prescribed format and details of methodology for planning, execution, monitoring and completion of the project. The methodology so adopted shall suit to the nature of work and shall also comply fully with best practice and current regulations. A comprehensive detailing for each activity like setting-up organization, safety plan, execution plan, quality assurance plan, sequence of work to achieve the mile stones, ensure targeted progress and quality and in turn deployment of resources, risk analysis and its mitigation strategy shall be given communication arrangement within his organization and with the railways for decisions, progress or any other matter connected with this project to ensure full information about the project including progress of work at different time scale shall also be furnished.
List of works completed in the last seven financial years giving description of work, organization for whom executed, approximate value of contract at the time of award, date of award and date of scheduled completion of work. Date of actual start, actual completion and final value of contract should also be given.
Supportive documents/certificates from the organizations with whom they worked/are working as list of works completed and list of works on hand should be enclosed.
List of works on hand indicating description of work, contract value, and approximate value of balance work yet to be done and date of award.
Uploading of declaration regarding Employment/Partnership etc. of Retired Railway Employees as per GCC-2022 . (ANNEXURE attached).
Uploading of Tender Forms shall embody the contents of the contract documents either directly or by reference and shall be as per specimen form, e-Tender Forms shall be issued free of cost to all tenderers.
A copy of certificate stating that they are not liable to be disqualified and all their statements/documents submitted along with bid are true and factual. Standard format of the certificate to be submitted by the bidder is enclosed as Annexure-V. In addition to Annexure-V, in case of other than Company/Proprietary firm. Annexure-V(A) shall also be submitted by the each member of a partnership firm/Joint Venture (JV)/ Hindu Undivided Family (HUF)/ Limited Liability Partnership (LLP) etc. as the case may be.Non submission of a copy of certificate by the bidder shall result in summarily rejection of his/their bid. It shall be mandatorily incumbent upon the tenderer to identify, state and submit the supporting documents duly self attested/digitally signed by which they/he are/is qualifying the Qualifying Criteria mentioned in the Tender Document. (As per Railway bord letter no.2022/CE-l/CT/GCC- 2022/Policy dt. 13.12.2022)
Declaration form regarding site etc.
Declaration regarding constitution of firm .
Engineers/Personnel .
Performa of Completion Certificate .
All tender conditions shall be strictly complied with as per the Indian Railways Standard General Conditions of Contract (GCC), April 2022, along with all subsequent correction slips issued thereof.
Reliability improvement work of signalling & telecom gears under jurisdiction of ADSTE/MBA (MBA-TKMG) section of Jhansi division.
JHS-N-W-35-26
JHS-N-W-35-26
Open
Works - General
12 Months
Jhansi, Uttar Pradesh
₹0
₹3.1 L
8 May 2026
14 Apr 2026
24 Apr 2026
124 items across 2 schedules
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 1,14,35,297.85 | ||
| — | 25.00 | — | — | ||
| Supply of Electric Point Machine 143 mm stroke, AC Immunity 160V AC, complete with lock detector and slides for lock detector, Non-trailable, to operate on 110V DC, rotary locking with crank handle universal type as per RDSO Spec. No. IRS:S-24/2025 (Rev 3) or latest, RDSO DRG. NO S- 10800 (ALT.5) WITH JUNCTION BOX TELESCOPIC. THE MOTOR WILL BE AS PER RDSO SPECN. NO. IRS: S-37/2002 (Ver 2.0 or latest) WITH RDSO DRG. NO. S-10910. This includes supply of Set of tools as per para 20.1 & 20.2 of RDSO SPEC. NO. IRS:S-24/2025 (Rev 3 or latest) The following set of tools in a suitable tool box shall be supplied along with every set of eight point machines or less. i). Hand operated square drive socket wrenches of 12.5 mm driving square (short type) as per IS: 7381 for M8, M10, M12 & M18 threads. (One 250 mm long 12.5 mm square extension bar as per IS: 7991 alongwith compatible Tee handle Square drive as per IS: 7975 suitable for above socket wrenches shall also be provided.) ii). Open jaw wrenches (spanners) for M10, M12, M20, M24 & M33 threads as per IS: 2028. iii). Adjustable wrench. iv). Screw driver 300 mm long. v). Two Junction box and two numbers of telescopic pipes of approved type shall be supplied as an integral part of the point machine.(Inspection Agency-RDSO). | — | — | — | 25,10,062.5 | |
| — | 450.00 | — | — | ||
| Supply of uncharged Low Maintenance Lead Acid (LMLA) secondary cell, 2V, 80 AH, in dry condition, shelf mounting type, conforming to RDSO Specn.No.IRS:S-88/2004 or latest, with inter cell connectors, nuts and bolts, washers, microporous vent plug, float etc.(Inspection Agency- RDSO/RITES). | — | — | — | 14,37,957 | |
| — | 60.00 | — | — | ||
| Supply of uncharged Low Maintenance Lead Acid (LMLA) secondary cell, 2V, 200 AH, shelf mounting type conforming to RDSO Specn.No.IRS:S- 88/2004 or latest with inter cell connectors, nuts and bolts etc.(Inspection Agency-RDSO). | — | — | — | 3,42,417 | |
| — | 65.00 | — | — | ||
| Supply of basic material to construct unit maintenance free earth as per RDSO Specs. No RDSO/SPN/197 Ver. 1.0 or latest to achieve a resistance less than 1 ohm. It consist of following: (a) Copper bonded steel electrode of minimum 3.0 m long, minimum 17.0 mm dia with copper bonding thickness of minimum 250 microns and UL listed and marked = 1 no. (b) Earth enhancement material supplied in sealed bags of minimum 10 kg = 3 nos. (c) Copper strip of 150x25x6 mm, to terminate earth rod = 1 no. (d) Copper strip of 300x25x6 mm (MEEB) = 1 no. (e) Copper strip of 150x25x6mm (SEEB) = 1 no. (ii) Supply of 35 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting main earth electrode to MEEB in the equipment room in duplicate.(minimum 10 meter) (iii) Supply of 16 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting MEEB to SEEB and SPD to MEEB (minimum 10 meter ) (iv) Supply of 10 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting various equipments to SEEB (v) Supply of copper lug sleeve for 3/16 cable.(Inspection Agency-RDSO/RITES). | — | — | — | 11,72,763.8 | |
| — | 100.00 | — | — | ||
| Supply of B Type Choke as per RDSO Specn.No.IRS:S-65/83 (Amnd. 3) or latest. (Inspection Agency-RDSO/RITES). | — | — | — | 5,90,913 | |
| — | 600.00 | — | — | ||
| Supply of Indicative type of fuse inserts with holder, 1.6 Amp, as per IRS S: 78/2006 or latest, make Rapid, Malnad, L&T or similar of reputed make.(Inspection Agency-RDSO). | — | — | — | 43,440 | |
| — | 540.00 | — | — | ||
| Supply of Indicative type of fuse inserts with holder, 0.6 Amp, as per IRS S: 78/2006 or latest, make- Rapid, Malnad, L&T or similar of reputed make.(Inspection Agency-RDSO). | — | — | — | 37,459.8 | |
| — | 1000.00 | — | — | ||
| Supply of Indicative type of fuse inserts with holder, 6/10 Amp, as per IRS S: 78/2006 or latest, make Rapid, Malnad, L&T or similar of reputed make.(Inspection Agency-Consignee). | — | — | — | 2,70,590 | |
| — | 2000.00 | — | — | ||
| Supply of PPTC fuse GP 60-185, UL-94 certification (1.6 Amps) for internal/external current. Make Fuzetec, Tyco, Raychem, Little fuse or similar.(Inspection Agency-Consignee). | — | — | — | 19,860 | |
| — | 2000.00 | — | — | ||
| Supply of PPTC fuse GP 60-400, UL-94 certification (12 V/4 Amp) for TF,TR circuit. Make Fuzetec, Tyco, Raychem, Littlefuse or similar.(Inspection Agency-Consignee). | — | — | — | 16,760 | |
| — | 2000.00 | — | — | ||
| Supply of PPTC fuse GP 250-185, UL-94 certification (24 V/ 4 Amp) 110V AC for Track Chargers. Make Fuzetec, Tyco, Raychem, Little fuse or similar.(Inspection Agency-Consignee). | — | — | — | 16,760 | |
| — | 20.00 | — | — | ||
| Q-Series Neutral Line Relay, non-AC immunised, (QN1 Type), 8F/8B, 24V DC complete with plug board(base plate), connectors and retaining clips etc and conforming to BRS- 930 and RDSO Specn.No.IRS:S-34 ,S-23, S-60 or latest, as applicable. The interlocking code for this unit shall be "ABCDF".(Inspection Agency-RDSO). | — | — | — | 72,788.2 | |
| — | 2000.00 | — | — | ||
| Supply of Disconnect Terminal block for four conductors with screwing cage /clamp type, sliding switch disconnect, as per RDSO spec.No. RDSO/ SPN/189/2004 Ver. 3.0 or latest, for each conductor size up to 2.5 sq. mm, equivalent of M6 terminals. Each terminal block equipped with two markers, on top and bottom, an end plate, two end clamps and adequate length of rails for fitting terminal blocks.(Inspection Agency-RDSO). | — | — | — | 3,85,440 | |
| — | 65.00 | — | — | ||
| Supply of Track Lead Junction Box (TLJB),4way, made from FRP, as per Drg.No.20101/M (IRS) or latest, including brass bolts and hylam board sheet with terminals etc. The FRP material shall be as per RDSO spec.RDSO/SPN/151/1997 or latest. The technical specifications are as follows:(a) TLJB complete with cover to be in black/red/grey with all the holes required for mounting on FRP stump (vertical two for each FRP angle) HDPE pipe , cable etc.(b) Each TLJB shall have two bakellite terminal block fitted horizontally, each bakellite terminal block shall have two nickel chrome plate with brass terminal. Along with each TLJB, nickel chrome plated brass links(two nos. of adequate strength for vertical linking of the terminals to be supplied.(c) HDPE pipe along with two nuts for fixing on the TLJB hole .(d) The FRP stump for mounting the TLJB.(Inspection Agency- Consignee). | — | — | — | 3,55,227.6 | |
| — | 65.00 | — | — | ||
| Supply of Track feed Battery Charger as per RDSO Specn. No.IRS: S-89/2013 Ver. 1.0 or latest. Charging capacity rating should be suitable for charging 80 AH Battery.(Inspection Agency- RDSO). | — | — | — | 3,83,536.4 | |
| — | 1.00 | — | — | ||
| Supply of managed STM-1, SDH (STM-1 Add/Drop MUX and upgradeable to STM-4) fully wired for 2 X 63 MB and equipped for 21 Els and minimum 4 port of 10/100 base T electrical interface (with LCAS and GFP), including power supply, order wire, Ethernet card, sub rack, inbuilt DDF, installation material and all other accessories and other common cards, manuals etc. as per TEC GR No. TEC/GR/TX/SDH - 004/04.Jan 2011 or with latest amendment. It shall be equipped with redundant power supply card. The contractor will supply all other accessories as mentioned in the above said TEC Specifications and system will have provision of different redundancy cards as per the TEC Specifications. Each node shall support mapping of management function to E1 signal. The equipment shall be compatible to the existing SDH system (if any) and NMS system (if any) in the section. This includes connecting all pig tails, optical patch cords etc. to the SDH equipment. Note: It shall be possible to increase capacity from 21E1 to 63 Els by adding / inserting tributary cards. This includes connecting all pig tails, optical patch cords etc. to the SDH equipment. This also includes connecting the SDH equipment with all cards to the 48V Bus including supply of wires and connectors. Termination of all E1s on DDF taking PVC cable over runway or a wall.(Inspection Agency-RDSO). | — | — | — | 2,36,630.25 | |
| — | 1.00 | — | — | ||
| Supply of 2 KVA online UPS with Battery of 48AH (04 Nos) of reputed brand. The detailed specification is as under, I/P - single phase 160-260 volt, O/P voltage single phase 230+- 0.5%, Output frequency 50+-0.5% Hz,Technology - IGBT-PWM or better, other accessories - 6m cables, rack for batteries etc. Make - Luminous/V-Guard/Exide/Microtek or better.(Inspection Agency- Consignee). | — | — | — | 86,681.34 | |
| — | 10.00 | — | — | ||
| Supply of 2.048 Mbps, Managed SHDSL modems, as per RDSO spec. no.RDSO/SPN/TC/80/2020, Rev.2.0 or latest with suitable connector. A pair consists of V.35 and G.703 interfaces.(Inspection Agency-Consignee). | — | — | — | 3,29,300.3 | |
| — | 12.00 | — | — | ||
| Supply of CO2 type fire extinguisher capacity 4.5 Kg capacity ISI marked, with all accessories, operating temperature (-30) © to (50) ° for class 13 B type of fire with 1 mtr. long hose pipe fitted with PVC bend horn, with carying handle and wall mounting brcket, complete in all respect. It should conform to IS 2878:2004. Extinguisher certificate has to be supplied along with the item.(Inspection Agency-Consignee). | — | — | — | 60,603 | |
| — | 4.00 | — | — | ||
| Supply of Non Metallic (FRP) colour light signal housing multi unit type for railway signaling suitable for RE area THREE Aspects, complete without lenses, lamps and signal transformer as per RDSO DRG. No. SA 23002 A/M (Adv.) and as per RDSO spec. No. RDSO/SPN/194/2006 (Rev 2.0) or latest and FRP material as per RDSO SPEC. No. RDSO/SPN/151/1997 or latest.(Inspection Agency-Consignee). | — | — | — | 1,42,949.48 | |
| — | 4.00 | — | — | ||
| Supply of Junction route indicator unit 2 way/ 3 way, made of FRP, (Without Lenses & Holder) as per Drg. No.SA 23401-06 (Adv.) (as applicable) suitable for LED Signal Lighting Unit and as per RDSO spec. IRS: S-66/84 Amd.-1 or latest and RDSO/SPN/194/2006 Rev.2 or latest.(Supply of LED Unit is not covered in this item).(Inspection Agency-Consignee). | — | — | — | 1,81,834.44 | |
| — | 100.00 | — | — | ||
| Supply and Provision of indicative type Surge Protection Device Class D Protection Device for 24V DC (spark gap type) between Power and Signalling equipment as per the instructions of the Engineer incharge at site. (SPD with potential free contacts shall be of approved make like OBO/DEHN/PHOENIX/LPT/JMV/CITEL or superior make and other miscellaneous materials required for the work shall be supplied by the contractor as per Annexure-B.(Inspection Agency-RDSO/RITES). | — | — | — | 6,02,682 | |
| — | 10.00 | — | — | ||
| Supply of S&T Relay Room Key Box cabinet front glass with hammer.(Inspection Agency-Consignee). | — | — | — | 6,726 | |
| — | 17.00 | — | — | ||
| Supply of RS-232 to Fiber Converter or RS-232 to Quad Modem (as per media availability) for operating UFSBI equipment as per IRS Spec. No.IRS:S-104/2012Ver. 0 on dark Optic Fiber Cable.(Inspection Agency-RDSO/RITES). | — | — | — | 10,86,489.72 | |
| — | 25.00 | — | — | ||
| Supply and installation of earth electrode as per standard practice and as per NCR latest practice. It includes supply of GI pipe of 3 meter length. It includes connecting the earth electrode to the equipments which are required to be earthed including digging of earth pit 3 meter deep and fixing earth electrode pipe, casting of cement concrete enclosure with cover (cover as per NCR latest practice). It includes installation of 7 strand GI wires as earth lead wires, supported on MS flat size 5mm x 40 mm, soldering and nut bolt both, one end of both earth lead wire and MS flat to earth electrode and other end to Location boxes, block equipments, power equipments, cable sheath, signals etc. as per site requirement and as per instructions given by engineer incharge. (Inspection Agency-Consignee). | — | — | — | 83,838.5 | |
| — | 25.00 | — | — | ||
| Fabrication and supply of point rodding (Ground Connection) set for electric point machine (RDSO Type) as per RDSO Drg. No.SA-8800-01, 20. 21, 9151-52,9000-01,03-04,9065- 66,9101, as applicable.(Inspection Agency-Consignee). | — | — | — | 3,68,231.75 | |
| — | 25.00 | — | — | ||
| — | 2.00 | — | — | ||
| Supply and Installation of Modular power supply arrangement for VDU (43"" 85"") and industrial PC (Embedded PC) with input and output redundancy arrangement and Hot plug able Modules . 1. Input O-ring diode module with potential free-1 No contacts (PFC) for two 110 VDC sources from IPS and single 110V DC bus. 2. Isolated Inverters (Master / slave) - 02 Nos. Input-110 V DC Output : 120 V AC/220V A500VA 3. Isolated DC-DC convertors- 02 nos. Input : 110 v DC Output : 24 V DC/ 10A 4. 3U SS rack with back panel mother board /front panel power connectors inverter auto change over switch and all required over switch and all required protection circuits as per RDSO specification. Make Gallant or superior.(Inspection Agency-RDSO/RITES). | — | — | — | 5,13,637.02 | |
| — | — | — | 40,40,387.33 | ||
| — | 1.00 | — | — | ||
| Installation, wiring, testing & commissioning of managed SDH (STM-1 Add/Drop MUX and upgradeable to STM-4) equipments, with all accessories and power supply connections,fixing of ladder etc. in OFC/Relay room. | — | — | — | 32,614.27 | |
| — | 1.00 | — | — | ||
| Auto CAD engineer to be provided by contractor (the CV to be got approved by railway Engineer representative) Work of his/her given in technical specifications (He or She)/ Month will do duty in Sr.DSTE/JHS office as well as in Field for making signaling drawing Survey etc. | — | — | — | 31,233.72 | |
| — | 2.00 | — | — | ||
| Casting, concreting and curing of foundation for Main Signal Post in the ratio of 1:3:6 as per NCR drg.No. TYP/013/14/SIG FOUND. dtd 12.11.2014 (total 2 sheets of drawing) issued vide NCR Letter No. S&T/NCR/DRG/TYP dated 13.11.2014, using standard size of foundation/galvanized anchor bolts complete, required for erection of colour light signal post. Anchor bolts complete should comply with the RDSO drg. No. SA 116 A/M. Item includes excavation, ramming of CC using vibrator, curing and plastering with 1:4 cement-sand mixture (aggregate will not exceed 3.8 cm). Aggregate, cement, sand and holding down bolts will be supplied by contractor. Any machines & tools, if required for execution of this item, will be arranged/provided by contractor. | — | — | — | 27,012.56 | |
| — | 2.00 | — | — | ||
| Erection of CLS Post with base and signal unit on top or on Offset Bracket including erection of auxiliary signals like calling on, shunt signal if any. It includes fixing of all LEDs and wiring of complete signal including route and auxilliary signals, if any. It includes fixing of front and back staging, ladder and guards, signal name plates / boards, with contractor's own brackets and fixing materials. The work shall be done as per instructions of Rly engineer at site. It also includes provision & fixing of maintenance platform as per design given by Engineer -In-Charge at site. The Item includes cutting of Signal post if required by Site In charge. | — | — | — | 11,757.48 | |
| — | 450.00 | — | — | ||
| Charging of Lead Acid Batteries, 2V, 80 AH, with contractors own battery grade sulphuric acid and distilled water with minimum two charge - discharge cycles, installation of charged batteries in groups & their connection & wiring. The work shall be done as per the procedure prescribed by the OEM and extant practice of N.C.Rly and instruction of Engineer-in-charge. Detailed measurements of initial charging shall be recorded jointly by contractor & Rly's site-in-charge. | — | — | — | 1,14,264 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
ADVANCECORRECTIONSLIP7.pdf
ATTACHMENT
ADVANCECORRECTIONSLIP8.pdf
ATTACHMENT
ADVANCECORRECTIONSLIP9.pdf
ATTACHMENT
ADVANCECORRECTIONSLIP10.pdf
ATTACHMENT
GCC-2022change.pdf
ATTACHMENT
GCC 2022 Correction slip 4
ATTACHMENT
AdvanceCorrectionSlipNo_6.pdf
ATTACHMENT
DIPPtendercondition30.05.2025.pdf Validity of DIPP in Tender document
ATTACHMENT
RetiredRlyEmployee.pdf
ATTACHMENT
35-26TENDERBOOKLET1_1.pdf
ATTACHMENT
GCCcorrectionslip-5.pdf
ATTACHMENT
Annexure-VandAnnexure-V_A_.pdf Annexure V and Annexure VA
ATTACHMENT
2021Tele523part13425647.pdf
ATTACHMENT
AdvanceCorrectionSlipNo.2.pdf
ATTACHMENT
GCC-2022.pdf
ATTACHMENT
GCCACS11.pdf
ATTACHMENT
GCC 2022 Correction slip 3
ATTACHMENT
GCC2022ACS-3AdvanceCorrectionSlipNo.3.pdf
ATTACHMENT
2022-CE-I-CT-GCC-2022-PolicyCorrectionSlipNo.4.pdf
ATTACHMENT
Annexure-VandAnnexure-V_A_.pdf
ATTACHMENT
DIPPtendercondition30.05.2025.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .