SPECIAL REPAIRS TO BLDG NO. P-1329, P-1309 AND P-1525 UNDER VARIOUS UNTS AT MIL STN JAISALMER

Amount

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, laying of cable/pipe etc or for shafts, wells, cesspits, manholes, pier holes etc not exceeding 10 Sqm on plan and getting out in soft/ disintegrated rock complete all as specified & directed by Engineer-in-Charge.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soft/ disintegrated rock complete all as specified & directed by Engineer-in-Charge.

Removing excavated soft/ disintegrated rock to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed by the Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar, removeing and rubbish off the premises complete all as specified and directed by the Engineer-in-Charge.

M&L for 25mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregates as in flooring complete all as specified and directed by the Engineer-in-Charge.

M&L light shade, vitrified tiles, 10mm thick (minimum), (square/ rectangular polished, area of each tiles not exceeding 0.36 Sqm, in flooring set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bedding in CM 1:6 complete all as specified and directed by the Engineer-in-Charge.

M&L non skid ceramic coloured (Jointless) tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed by the Engineer in Charge.

M&L for Glazed ceramic coloured (Jointless) tiles 450x300x7mm thick in vertical surfaces etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10mm thick backing coat in CM (1:4) complete all as specified and directed by the Engineer in Charge.

M&L Machine cut kota stone slab flooring 20- 25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete laid over and including screed bed or bedding layer of 15mm thick in CM (1:6) complete all as specified & directed by Engineer-in-charge.

M&L for machine cut kota stone slab 18 to 20mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with pigment to match the shade of the slab including rubbing and polishing complete over and including 15 mm thick backing coat in CM (1:4) complete all as directed by Engineer-in-charge.

Demolition of stone/ boulder masonry and built in cement mortar including all quoins arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles and removal unserviceable materials, debris and rubbish complete all as specified & directed by Engineer-in-charge.

M&L for precast cement concrete (1:3:6) type C-1 using 20mm graded stone aggregate as in block masonry with solid blocks exceeding 10cm width and setting in cement mortar (1:6) including demolition of existing block masonry complete all as specified & directed by Engineer-in-charge.

M&L for squared rubble walling, Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) complete all as specified & directed by Engineer-in-charge.

M&L for squared rubble walling, Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) but except stone complete all as specified & directed by Engineer-in-charge. Note :- serviceable stone obtained from demolition shall be used.

Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge not exceeding 20mm & dressing face beds and joints as specified to squared rubble walling Jodhpur type brought up to courses complete all as specified & directed by Engineer-in-charge.

Taking down cement or cement lime plaster, any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified & directed by Engineer-in-charge.

M&L for rendering 15mm thick on brickwork or concrete on wall surfaces in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified & directed by Engineer-in-charge.

M&L for rendering 15 mm thick on stone masonry surfaces or surfaces other than fair faces of brick work or on one side of lathing in cement mortar 1:6 & finished the surface even & fair without using extra cement complete all as specified & directed by Engineer-in-charge.

S&F collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified & directed by Engineer-in-charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of distempering oil emulsion over a coat of primer complete all as specified & directed by Engineer-in-charge.

M&L for rendering 15 mm thick on stone masonry surfaces or surfaces other than fair faces of brick work or on one side of lathing in cement mortar 1:4 & finished the surface even & fair without using extra cement all as specified. Note : Supply only liquid water proofing compund shall be measured and paid separately.

M&L for preparing new plastered or un plastered surfaces and applying two coats of cement base paint on surfaces of walls, column, beam, chajjas etc. complete all as specified & directed by Engineer-in-charge.

M&L for Complete removal of existing treatment and applying two coats of cement base paint on surfaces of walls, column, beam, chajjas complete all as specified & directed by Engineer-in-charge.

Supply only liquid water proofing compound in sealed pack (ISI Marked) complete all as specified & directed by Engineer-in-charge.

Taking down all loose plaster and concrete if any in RCC columns, Chajjas, beams,slabs or any other type of RCC members,removing all loose ruts/scale from reinforcement etc by using wire brushes ,sand paper or any other chemicals, applying a coat appoxy coating on old reinforcement, tying IRC fabric of size 75x75mm of 3mm dia and binding with mild steel wire annealed with exsting reinforcement and applying cement slurry uniformaly to exposed surfaces and gunniting using CM 1:3 average thickness of gunniting not less then 30mm and finishing the surfaces with 10mm thick rendering in CM 1:4 finished even and smooth with out using extra cement and removing the debris from the site, complete all as specified and directed by Eng-in-charge.

M&L for Forming jambs, etc., to openings (to foregoing item), with stone supplied by MES including cutting, toothings and properly bonding into old work, including facing and pointing (if necessary) to match existing work, complete all as specified & directed by Engineer-in-charge.

M&L for rendering 5 mm thick in CM (1:3) on fair faces of concrete surfaces as in ceiling finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.

M & L for complete removal of existing treatment on ceiling and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surfaces and applying two coats of white wash on walls complete all as specified and directed by Engineer-in-Charge.

M&L for complete removal of existing treatment and applying one coat of white wash on walls, column, beam, chajjas etc. complete all as specified and directed by Engineer-in-Charge.

M&L for complete removal of existing treatment and applying two coats of distemper oil emulsion on surfaces of walls complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new or previously untreated steel surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red- oxide, zinc chrome primer complete all as specified & directed by Engineer-in-Charge.

M&L for preparing new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer complete all as specified & directed by Engineer-in-charge.

M&L for prepartion of old painted wood or wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed by Engineer-in-charge.

Demolition of cement concrete (un reinforced) in ground floors and pavings n.exc 15 cm thick (below or above ground level) & removing rubbish out side MD land complete all as specified & directed by Engineer-in-charge.

M & L for hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed by the Engineer-in-Charge.

M&L for plain cement concrete (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in foundations, filling & mass concrete all as specified & directed by Engineer-in-Charge.

M&L for forming Contraction (dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade 'A' complete all as specified and directed by the Engineer-in-Charge.

Taking down chowkats or frames (without taking off shutters from the frames) area not exceeding 1.5 Sqm each incl making good the disturbed surface in PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate or CM 1: 3 and white wash and cement base paint complete all as specified & directed by Engineer-in-charge.

Taking down chowkats or frames (without taking off shutters from the frames) area exceeding 1.5 Sqm but not exceeding 4 Sqm each incl making good the disturbed surface in PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate or CM 1: 3 and white wash and cement base paint complete all as specified & directed by Engineer-in-charge.

Taking down shutters of any description exceeding 1.00 Sqm but not exceeding 2.00 Sqm each complete all as specified & directed by Engineer-in-charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified & directed by Engineer-in-charge.

S&F framed work such as grills, gratings, etc with ends of bars shouldered and / or riverted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, raillings, frame work of water tanks and similar work confirming to Fe-290 grade E-165 complete all as specified & directed by Engineer-in-charge.

Supply and fix steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified & directed by Engineer-in-charge.

S & F in repair 35 mm thick factory made second class hard wood, Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified & directed by Engineer-in-charge.

S&F in repair factory made 35mm thick 2nd class HW glazed and skelton shutter and open rebated and prepared to receive glass, gauge etc (without sash bars), edges or framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Part I section 8 clause 8.24 (a) supplied and fixed to chowkats.

S & F in repair Galvanized mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples complete all as specified & directed by Engineer-in-charge.

S&F 150 mm long Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified & directed by Engineer-in-charge.

S&F 150 mm long Aluminium handles, cast type, anodised complete all as specified & directed by Engineer-in-charge.

S&F 125 mm long Aluminium handles, cast type, anodised complete all as specified & directed by Engineer-in-charge.

S & F MS Pressed handle 150mm size oval type stove enameled black complete all as specified & directed by Engineer-in-charge.

S&F mild steel butt hinges, medium weight cold rolled 100mm size complete all as specified & directed by Engineer-in-Charge.

S&F mild steel butt hinges, medium weight cold rolled 75mm size complete all as specified & directed by Engineer-in-Charge.

S & F mild steel tower bolts 150 mm long stove enameled black with bright bolt complete all as specified & directed by Engineer-in-charge.

S&F in repair aluminum powder coated partition wall of aluminum section 100mm x 44mm x 2mm thick frame rectangular section and panel 12mm thick prelaminated board in bottom panel and 5.5mm thick sheet glass in top panel with rubber lining and aluminum beading around length including necessary fixing arrangement for bottom and top member of aluminum frame in floor/PCC/Brick work as per site requirement with rawl plug etc, including chromium plated steel screws 60cm centre to centre complete all as specified & directed by Engineer-in-charge. (Note :- Rate quoted by the Contactor shall deemed to inclusive of 12mm thick prelaminated board and 5.5mm thick sheet glass).

Supply fabricating and fixing in repair of aluminium door powder coated of extrusion aluminium section including frame work complete, consisting of frame vertical and horizontal members, of size 104mmx44.45mmx 1.8mm thick. Vertical style of door shutter of size 85mmx44.45mmx 1.8mm thick. Top, middle and bottom rial of size 85mmx44.45x1.8mm thick and partially 5 mm thick plain/tinted sheet glass of partially prelaminated particle board 9 to 10mm thick with aluminium bedding and rubber gasket/beading including frosted film as desired fixing of hydraulic floor spring one in single leaf or two nos in double leaf door. One mortice lock for aluminium door (each) and two aluminium tower bolts for each door. Fixed with rawl plug including rectification of floor/wall to match the existing surfaces all as specified and as directed by Engineer-in-Charge at site. Note :- Rate quoted shall deemed to inclusive of partially 5 mm thick sheet glass with sun control film and partially 12mm thick prelaminated particle board.

S&F powder coated aluminium sliding window comprising of sliding runner of three way (track), consisting of two sliding shutter duly fitted with 5.00 mm thick glass and one shutter duly fitted with stainless steel wire cloth of 0.36mm nominal dia of wire & average width of aperature 1.4 mm with and including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc and down push type locking arrangement in glass shutter including necessary fixing arrangement i.e. rawl plug etc complete all as specified and directed by Engineer-in-charge.

Supply & fixing of false ceiling in step (s) comprising of 12 mm thick Gypsum board including GI frame work for seamless ceiling made of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 M length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including two coats of plastic emulsion paint including dismantling boarding of any description complete all as directed. (Note : The measurement shall be made from wall to wall without considering step(s)/overlap at steps)

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty approved by Engr-in-Charge

S&F 30mm thick of Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, uppling & fixing in the frame at site as per specification & drawing etc complete all as specified & directed by Engineer-in-Charge.

S&F solid PVC door frame of size 50x47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. Square tube suppling and fixing in opening as per specification and drawing complete all as specified & directed by Engineer-in-charge.

S & F in repair solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with MSD square tube etc complete all as specified & directed by Engineer-in-charge.

S & F in repair factory made solid PVC moulded masonic door shutter 28 to 30 mm thick (style) with 2, 4, 6 raised panel design with 2 mm moulded PVC sheet on the front face and 2 mm moulded PVC sheet on back face supply and fixing in the frame at site as per specification with particle board core complete all as specified & directed by Engineer-in-charge.

S&F flush pipe of polyethylene of low or high density of PVC 32mm dia for low level flushing cistern / WHB complete all as specified & directed by Engineer-in-charge.

S & F in repair vitreous china squatting pan orissa pattern complete of size 580 x 440 mm white with intagral foot rest and making good to the floor complete all as specified & directed by Engineer-in-charge. (Make:-Cera Cat No S3010102, Hindware Cat part No - 20042 or equivalent in Appx 'C' list of makes)

S&F in repair PVC low level white flushing cistern syphonic action type 10 ltrs capacity incl flush pipe 32 mm dia incl PVC connection 450 mm long and complete all as specified & directed by Engineer-in-charge. (Make:-Cera Cat part No B1010102 or equivalent in Appx 'C' list of makes)

S&F in repair 700 x 500 mm 5 mm thick glass mirror with double coat for protaction and longevity grounded edges for safety and siliver plating on the back for better reflection complete all as specified & directed by Engineer-in-charge. (Make:-Prayag Cat part No BLM-01,Cera Cat part No B3510112 or equivalent in Appx 'C' list of makes).

S&F 140 mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drwn steel spring, fixed in floor complete all as specified & directed by Engineer-in-charge.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame exc 1.5 sqm including punching or drilling out old glazing pins/ springs clips and providing and fixing new ones complete all as specified & directed by Engineer-in-charge.

S&F in repair MS powder coated drapery rod 25mm dia decorative manner all as per sample complete all as specified & directed by Engineer-in-charge.

S&F in repair brackets powder coated fancy type for drapery rod complete all as specified & directed by Engineer-in-charge.

S&F 15mm bore dia steel water tubing (ISI marked) medium grade galvanised with all fittings and fixed to walls and ceiling or laid in floors including taking down existing pipe complete all as specified and directed by Engineer-in-charge.

S&F 20mm bore dia steel water tubing (ISI marked) medium grade galvanised with all fittings and fixed to walls and ceiling or laid in floors including taking down existing pipe complete all as specified and directed by Engineer-in-charge.

S & F in repair bib tap 15 mm dia cast copper alongwith crutch or butterfly handle screwed down CP fancy type complete all as specified and directed by Engineer-in-charge.

S & F in repair stop valve 15 mm bore CP fancy type screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for union complete all as specified and directed by Engineer-in-charge.

S & F in reapir 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors fixed to walls complete all as specified and directed by Engineer-in-charge.

Dismantling Trellis work (Jafri), including taking as under of battens in trellis (posts and rails measured separately) complete all as specified and directed by Engineer-in-charge.

M&L for 35mm thick precast cement concrete louvers and jallies (1:3:6) type C-0 (using 12.50mm graded stone aggregate) (measured solid), including all mouldings but excluding frame, set in cement mortar 1:4 complete all as specified and directed by Engineer-in-charge.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer-in-charge.

S&F in repairs CP waste coupling 32mm for kitchen sink/Wash hand basin complete all as specified and directed by Engineer-in-charge.

S&F in repairs PVC waste water pipe for WHB of size 32 mm dia and 60 cm long including coupling complete all as specified and directed by Engineer-in-charge.

S&F 1000 litres capacity Three Layers White colour Rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including taking down old existing PVC tank complete all as specified and directed by Engineer-in-charge.

S&F in repair PVC ball valve 20 mm dia high pressure with polythene float and fly nut complete screwed for iron pipe or brass fernule and fixed complete all as specified and directed by Engineer-in-charge.

S&F in repair vitreous China Ware Wash hand basin white, flat back, size 550 x 400 mm size including cutting for and pinning ends of brackets or erecting stand complete all as specified and directed by Engineer-in-charge.

S&F in repair 15mm dia pillar taps cast copper alloy with capstan head chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe complete all as specified & directed by Engineer-in-Charge.

S & F in repair cock cast copper alloy fancy type chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed 15mm dia and fixed complete all as specified and directed by Engineer-in-charge.

S & F in repair Soap dish, chromium plated complete all as specified and directed by Engineer-in-charge.

S & F in repairs Chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed by Engineer-in-charge.

S&F in repair towel rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as specified & directed by Engineer-in-charge.

S & F in repair 5.5 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares n.exc 0.5 Sqm in each pane complete all as specified & directed by Engineer-in-charge.

S & F in repair PVC connections 15mm size with PTMT nuts of length 300mm complete all as specified & directed by Engineer-in-charge.

Taking down carefully surface aluminium or copper point wiring with PVC casing-caping (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc and making good disturbed surfaces complete all as specified & directed by Engineer-in-charge.

Taking down the existing unserviceable main switch / cut out / DBs of any type / capacity / description as existing at site including MCBs any type and capacity making good the disturbed surfaces to match with the existing finishes complete all as specified & directed by Engineer-in-charge.

Taking down the existing unservicable sub main wiring of any type / description as existing at site including making good the disturbed surfaces to match with the existing finishes complete all as specified & directed by Engineer-in-charge.

Taking down old unsv building security light fittings complete all as specified & directed by Engineer-in-charge.

Taking down old unsv /rusted GI braket suitable for security light fittings complete all as specified & directed by Engineer-in-charge.

Taking down of old unsv tubelight fitting /surface panel light / flood light/ bulb of any description light fitting any type any watt complete all as specified & directed by Engineer-in-charge.

Taking out carefully copper/GI earthing complete including GI pipe with copper orGI strip and removing materials and making good disturbed surface complete all as specified & directed by Engineer-in-charge.

Taking down Old unsv single pole and neutral enclosure with a two pin and earth plug and socket with 20 Amps MCB SP complete all as specified & directed by Engineer-in-charge.

M& L Point wiring with 1100 volts grade PVC insulated FR-LSH multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal boxes of thickness not less than 1.2 mm with 3 mm thick phenolic laminated white sheet cover for mounting of Piano Type switches, sockets, fan regulators complete for the following :-

(a) One light point controlled by one switch.

(b) One Ceiling /Exaust fan point controlled by one switch.

(c) One socket outlet 6 amp controlled by one switch on the same board with other switches.

(d) One socket outlet 6 amp controlled by one switch on indepdendent board.

All as above item No 101.00 but M& L Point wiring with 1100 volts grade PVC insulated FR multistranded copper conductor cable 4.0 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4.0 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal box of thickness not less than 1.2 mm covered with 3 mm thick phenolic laminated white sheet cover for one 16 amp socket outlet controlled by one switch on independent board complete all as specified & directed by Engineer-in-charge.

S&F switch piano flush button single pole one way 5/6 amp complete all as specified & directed by Engineer-in-charge.

S&F switch piano flush button single pole one way 16 amp complete all as specified & directed by Engineer-in-charge.

S&F socket outlet 2 in 1, 5 pin & 16 amp flush typecomplete all as specified & directed by Engineer-in-charge.

S&F socket outlet 2 in 1, 3 pin, 6 amp, flush type complete all as specified & directed by Engineer-in-charge.

S&F hum free electronic step fan regulator 120 - 280 volts of 100 watt capacity (socket type) including connecting up complete all as specified & directed by Engineer-in-charge.

S&F ceiling rose 6 amp, 3 plates polycarbonate body complete all as specified & directed by Engineer-in-charge.

M&L Point wiring used approved colour coding as per IS (Red, Black and Green) for single phase circuits), with multi-stranded copper conductor 1.5 sqmm nominal cross -sectional area, single core, PVC insulated and unsheated FRLS cable 1100 volts grade, ISI 694 marked with valid CML No. in and including medium grade, PVC concealed conduit, ISI marked of dia not less than 20 mm and conduit accessories concealed in wall/roof/floor etc, ISI marked with valid CML No. (IS-9537 - 1983 for condits and IS : 3419 - 1976 for conduit accessories) with terminated to new pressed flush metal boxes readily available cover with outer plates inner plates et, suitable for mounting modular type switches, socket fan regulator etc PVC insulated multistanded copper conductor 1.5 Sqmm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for the following :- Note : Modular switch and socket shall be measured and paid separately.

a) One light point controlled by one switch

b) One ceiling/exhaust fan point controlled by one switch

(c) One 2/3 Pin socket outlet 6 amp controlled by one switch on the same board with other switches.

(d) One socket outlet 6 amp controlled by one switch on indepdendent board.

All as per item No 109.00 above but pint wiring with 4.00 sqmm single core multi stranded copper conductor PVC insulated and unsheathed (FRLS) cable 1100 volts grade and 4.00 Sqmm PVC insulated and unsheated (FRLS) cable 1100 volts grade with multi stranded copper conductor as earth wire for 15/16 Amps multi porpose socket combination point on independent board. Note : Modular switch and socket shall be measured and paid separately.

S&F modular switch one way 6A, 1 module complete all as specified & directed by Engineer-in-charge.

S&F modular socket 6A-2/3 pin combined 2 module complete all as specified & directed by Engineer-in-charge.

S&F modular switch socket combined 6A/16A, 6 pin, 3 module complete all as specified & directed by Engineer-in-charge.

S&F step type modular fan regulator 120W -2 module ISI Marked with valid CML No complete all as specified & directed by Engineer-in-charge.

Supply and fixing of building security light fitting LED 35 Watt IP 66 IK 07 pressure dia cast aluminium housing with high efficient LED and PC cover having TOP opening sepreate drive compartment etc and connecting complete all as specified & directed by Engineer-in-charge.

S&F bracket of GI pipe light grade of 40mm bore dia, 1.2 meter in length, MS clamps made of FI 40 mm x 6mm incl nuts, bolts & washers including two coats of synthetic enamel paint over a coat of zink chrome primer complete all as specified & directed by Engineer-in-charge.

Supply and fixing of LED box type Integrated Batten, 40 watt having Aluminum Extruded housing in white powder coated finish with high translucent PC Cover, Elegant Design, IP 20 Protection. Size of fitting shall 1200 mm x 40 mmx 63 mm luminous output of the fitting shall not less then 4000 lm, CCT 5700 – 6500K, Surge Protector 4 KV, PF>= 0.95 , Separate detachable type Electronic constant current drivers for easy replacement and maintenance, THD < 10%, Necessary mounting arrangements. The Manufacturer of the fixture shall have in house NABL Accredited Lab and must produce certificate of the same along with LM-79 / LM80 / Test Report. Make PHILIPS CAT PART NO. BN100C LED40S-6500 PSU L120 GR S4 or equivalent in Appx 'C' list of makes.

S&F LED tube light fitting 10 watt tube LED Neutral white in colour, 600 mm in length wall mounted LED batten, extruded aluminium heat shink provided for efficient heat dissipation & integrated electronic driver, optic diffused type ENDURA LINER NEO including all electric connection with and including white flexible cord 1.50 Sqmm 3 core as required complete all as specified & directed by Engineer-in-charge.

S & F surface and wall mounted LED tube light along with fixture, 4 ft, 20 W, extruded aluminium housing provided for efficient heat disspation with polycarbonate ,operating voltage 240 V, 50HZ ,AC supply and operating tempureture 0 to 50 C ,power factor >0.9, lumen output > 2000 and provision of new 3 core multistanded copper conductor of size 23/0.193 from ceiling rose to fitting with white colour flexible pipe complete all as specified & directed by Engineer-in-charge.

Supply, installation, testing and commissioning of LED flood light fitting 120 Watts made out of pressure die cast aluminium housing and IP 66 protection with emmiter LED incl. making electric connection complete all as specified & directed by Engineer-in-charge. (Make of LED Lights :-Cromption cat ref LFLN-150-CDL/60M or equivalent in Appx 'C' list of makes).

S&F angle holder, insulated polycabonate body with back plate complete all as specified & directed by Engineer-in-charge.

Supply & Fix LED Bulb 9 Watt complete all as specified & directed by Engineer-in-charge.

S&F vertical DBs TPN 4 way 415 V double door powder coated, CRCA steel sheet constructed as per IS : 8623, degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required, suitable for TP/FP MCCB as incomer with MCCB 100A and with provision of SP/TP MCB's as outgoing MCCB FP 125 KA complete all as specified & directed by Engineer-in-charge.

S & F for sheet metal double door IP protection 43 enclosure MCB DB TPN 4 way with 200 Amps rated bus bar 415 volts double door with magnitic locking system complete all as specified & directed by Engineer-in-charge.

S & F for MCB DB SPN 12 way double door IP 43 complete prewired including Bus Bar etc suitable for operation on 240 volt 50 Hz AC including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good the distrubed surface to match with existing specification complete all as specified & directed by Engineer-in-charge.

S & F for MCB DB SPN 8 way double door IP 43 complete prewired including Bus Bar etc suitable for operation on 240 volt 50 Hz AC including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good the distrubed surface to match with existing specification complete all as specified & directed by Engineer-in-charge.

S & F for MCB DB SPN 4 way double door IP 43 complete prewired including Bus Bar etc suitable for operation on 240 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified & directed by Engineer-in-charge.

Supply and fixing 415V 10 KA 'C' curve MCB's TPN 40 to 100 Amps four pole and current carrying capacity in the DB with necessary connections and comissioning complete all as specified & directed by Engineer-in-charge.

Supply and fixing MCB's single pole and neutral 32 Amps, 240 Volts,10 KA rapturing capacity, 'C' curve complete all as specified & directed by Engineer-in-charge.

Supply and fixing MCB's single pole and neutral 40 to 63 Amps, 240 Volts,10 KA rapturing capacity 'C' curve complete all as specified & directed by Engineer-in-charge.

Supply and fixing MCB's single pole 6 Amps to 32 Amps, 240 Volts,10 KA rapturing capacity 'C' curve complete all as specified & directed by Engineer-in-charge.

M & L for submain wiring with approved colour code/as per IS (Red,black & green for single phase) concealed conduit circuit with two single core PVC insulated cable with multistranded copper conductor of nominal cross sectional area of 6.00 Sqmm (FRLS) in conduit including one run of PVC insulated multistranded copper conductor nominal cross sectinal area of 6.00 Sqmm (FRLS) of continous earth wire green in colour complete all as specified and directed by Engr-In-Charge. (Note :- Two runs of 6.00 Sqmm cable & one run of 6.00 Sqmm cable as earth wire and one run of PVC conduit shall be measured and paid as one unit length)

Supply and fixing of recessed/ceiling mounted down lighter with CRCA housing with high bright LED, idealy suited for low ceiling areas Brilliance 36 watt LED, size 2ft x 2ft The product features color tuning from 3000 K to 6500 K, necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting with white color flexible pipe complete all as specified & directed by Engineer-in-charge.

Supply & fixing single pole and neutral enclosure with a two pin and earth plug and socket complete with one SP MCB 20 Amps complete all as specified & directed by Engineer-in-charge.

Supply & fix heavy duty exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver complete all as specified & directed by Engineer-in-charge.

Taking down ceiling fan/exhaust fan of any sweep, dismanting blade and including preparation, filling cavity applying one coat of synthetic enamel paint by spraying with machine, re-assembling the fan body to fan and re-fixing in its original position or any other position as directed complete all as specified & directed by Engineer-in-charge. Note :- Rate quoted by the contractor shall deemed to inclusive of replacing of quarter pin, nut bolt with check nut, rubber real etc.

M & L bore earthing not less than 250 mm dia 16 feet deep filled with black soil up to 7 feet from bottom complete with galvanized iron pipe 40 mm bore medium grade 3 meter long tapers at bottom & provided 12 mm holes (staggered) at 75 mm centre to centre up to 2.5 meter of length from bottom , burried directly in ground filled with 45 cm alternate layer of chemical magnisium sulphate, charcoal & salt up to ground levl connected to galvanized iron strip 25x3 mm as earthing lead up to 7.5 mtr by means of bolt and nut, check nuts and washer of galvanized iron or steel including brazing work and 40mm dia light grade pipe for earth lead protection and testing complete all as specified & directed by Engineer-in-charge.

M & L bore earthing not less than 250 mm dia 16 feet deep filled with black soil up to 7 feet from bottom complete with galvanized iron pipe 40 mm bore medium grade 3 meter long tapers at bottom & provided 12 mm holes (staggered) at 75 mm centre to centre up to 2.5 meter of length from bottom , burried directly in ground filled with 45 cm alternate layer of chemical magnisium sulphate, charcoal & salt up to ground level connected to galvanized iron wire 4 mm dia as earthing lead up to Panel /DB BOX as per site requirement by means of bolt and nut, check nuts and washer of galvanized iron or steel including brazing work and 40mm dia light grade pipe for earth lead protection including test point terminal cover the earhing hole by PCC chamber and GI cover and testing on completion complete all as specified and directed.

NOTE FOR ITEM No. 137 & 138.00 [i]. Excavation & earth work in any type of soil including removing of surplus material upto 100M [ii]. PCC (1:3:6) type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC (1:2:4) type B1 cover 50x50 cm with 8mm round bar @ 15 cm C/C both ways. [iii]. Main earthing strip from earth electrode to test point upto 7.5 mtr. [iv]. Funnel with watering pipe [GI pipe] 20mm bore [ISI marked] medium grade & copper lugs and charcoal & salt as reqd. [v]. GI protection pipe of size 40 mm bore light grade 7.5m.

M&L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in pipe or fixed to DBs or any other indicated situation for loop earthing with GI strip of 25X3 mm size complete all as specified and directed Engg-in-Charge.

M&L in repair of for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in pipe or fixed to DBs or any other indicated situation for loop earthing with GI wire 4 mm mm size complete all as specified and directed Engg-in-Charge.

S&F steel water tubing 40 mm bore, 'light grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors in trench on pole for protection of cable etc and including taking down existing pipe of any description complete all as specified & directed by Engineer-in-charge.

S&F steel water tubing 20 mm bore, 'light grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors in trench on pole for protection of cable etc and including taking down existing pipe of any description complete all as specified & directed by Engineer-in-charge.

M& road cutting in trenches for laying cable protection pipe including making good the surface with top 200mm thick shall filled with PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) complete all as specified & directed by Engineer-in-charge.

Supply, laying and testing LT XLPE insulated, armoured heavy duty, electric cable, with aluminium conductor, 1100 volts grade, cross-sectional area 35 Sqmm 3½ Core and including taking down existing unserviceable cable complete all as specified & directed by Engineer-in-charge.

Supply, laying and testing LT XLPE insulated, armoured heavy duty, electric cable, with aluminium conductor, 1100 volts grade, cross-sectional area 16 Sqmm 4 Core and including taking down existing unserviceable cable complete all as specified & directed by Engineer-in-charge.

M&L for sand cushioning to under ground cable using tibba sand and gently punning to cushioning to cable complete all as directed by Engineer-in-Charge. (Note :- Punned thickness of sand cushioning shall only measured for the purpose of payment).

Supply & laying 40 to 50mm thick roughly hammer dressed Jodhpur stone patti cable cover 25cm to 30cm wide and not exc 60cm long each laid dry abutting with each other with maximum gap between adjacent slabs n. exc 10mm complete all as specified & directed by Engineer-in-charge.

S K TRADER

Leelashah Enterprises

BHAGWATI CONSTRUCTION

M/S MAYA CONSTRUCTION COMPANY