Construction of Boys Hostel for Horticulture Training Institute at COE, Reddiyarchatram, Dindigul District under NADP 2023-24

Amount

Earthwork excavation for foundation (for narrow excavation) to full depth as per designed in all soils and sub soils except soft disintegrated rock not requiring blasting and hard rock requiring blasting and bailing water wherever necessary. Refilling the sides of foundation with excavated earth other than sand in layers of well rammed and compacted and depositing the surplus earth in places shown by the departmental officers with an initial lead of 10m and initial lift of 2m and clearing and leveling the site etc. complete

Supplying and filling in foundation and basement with M - Sand in layers of not more than 15cm thick well watered, rammed and consolidated etc., complete as per standard specification.

Supplying and filling of Red gravel for basement in layers of not more than 15cm thick well watered, rammed and consolidated etc., complete as per standard specification.

Plain Cement concrete 1:4:8 (One cement four M sand and eight broken Machine crushed stone jelly) using HBG Machine crushed stone jelly of size 40mm gauge for founding and basement including de- watering if found necessary and laid in layers of not more than 15cms thick etc., complete complying with standard specification and as directed by the departmental officers.

Plain Cement concrete 1:2:4 (One cement Two M sand and four broken Machine crushed stone jelly) using HBG Machine crushed stone jelly of size 10-12 mm gauge for founding and basement including de- watering if found necessary and laid in layers of not more than 15cms thick etc., complete complying with standard specification and as directed by the departmental officers.

Plain Cement concrete 1:2:4 (One cement Two M sand and four broken Machine crushed stone jelly) using HBG Machine crushed stone jelly of size 20mm gauge for founding and basement including de- watering if found necessary and laid in layers of not more than 15cms thick etc., complete

Reinforced cement concrete 1:1.5: 3 (One cement one and half M sand and three broken Machine crushed stone jelly) using 20mm gauge hard broken granite jelly for all RCC works such as slabs, beams, footings, staircase waist slabs, steps, landing beams fins, boxing, vertical louver, drops, window sill slabs projection and other similar works including laying curing etc., complete

For Foundation and Basement

For Ground floor upto 4.50 m height

For first floor above 4.50 m height

Reinforced Cement Concrete 1:3:6 (One cement, Three sand and six broken stone jelly) using 40mm size hard broken stone jelly for dummy columns, excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc., complete. (Reinforced cement concrete 1:2:4 for slab to be extended upto top of splashing with pressed tiles and future extension rods to be embedded in CC 1:3:6 (One cement, three sand and six hard broken stone jelly) Dummy columns should be atleast 1 metre height)

For first floor above 4.50 m height

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Supplying and erecting steel centering including necessary supports for plane sufaces for Reinforced Cement Concrete works such as column footings, column pedastals, plinth beams, grade beams, staircase steps, etc., which required only nominal strutting using mild steel sheets of size 90cmx60cm and 10 BG stiffened with welded mild steel angles of size 25mmx25mmx3mm for boarding, laid over silver oak joists of size 10cmx6.5cm space at about 75cm centre to centre or at suitable intervals etc, complete in all floors complying with standard specification. ( Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting up to 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc

Brick work in following Cement Mortar using best quality of Second class ground moulded chamber burnt bricks 9"x4-3/8"x2-3/4" for foundation and basement including curing etc, complete complying with standard specification.

In cement mortar 1:6

In Ground floor

In First floor

In cement mortar 1:5

For Foundation and Basement

Brick partition wall in CM 1:3 (One of cement and three of M sand) 11.50CM thickness using IInd class chamber burned bricks of size 9”x 4 3/8”x2 3/4” and using hoop iron with reinforcement if found necessary etc.., complete

Foundation and Basement

11.50 cm thick Ground Floor

Plastering the walls with Cement Mortar 1:5 - 12 mm thick using the M sand including curing and finishing neatly complying with standard specification and as directed by the departmental officers etc. complete.

Special ceiling plastering and finishing all RCC exposed surfaces such as RCC slabs, sunshades, canopies, stair case steps, landing slabs etc with CM 1:3 (One cement and three M sand) 10mm thick including hacking the surfaces and providing necessary CM nosing, beading as per size specified wherever necessary using the same mix etc., complete complying with standard specification and as directed by the Departmental Officer.

Plastering with cement mortar 1:3 (one cement and three sand) 12mm thick with fine river sand for plastering including curing, neat finishing, etc., complete complying with standard specification and as directed by the Departmental officers.

Suplying and fixing of teak wood scantlings door frame of size 6" x 4" and Double door solid teak wood shutter frame of size 5" x 1 1/2 " and plank 1 1/4" thickness and over laying with SR resin or fevicol resin p inclusing the labour wrought and put up and door shutter in position and incuding labour charges for fixing furniture fittings and cost of fittings and polishing etc. complying with standard drawings and standard specification. - For Size 2.00 x 2.10 m

Paving the floor with best approved quality fine polished Kota stone slabs of size 600x600 of 18/20mm with machine cut edges matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using Cement mortar 1:3 (One cement and three sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with matching colouring pigments and polishing with floor polisher to a high degree of finish etc. The Kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on works, etc., complete as per standard specification

Using Fine Polished Rajasthan Kota stone slabs 20mm thick with Machine cut edges of size below 2'0"x2'0"

Paving the flooring with best approved quality and colour of Double charged Vitrified tiles of size 600x600x8mm over a base layer of cement mortar 1:3(One of Cement and three of sand) 20mm thick and pointing with same colour cement neatly etc., including the finishing the joints and appointing flush with even surfaces etc., as directed complying with standard specifications the tiles should be got approved by the Executive Engineer before use on work.

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the flooring with plain ceramic tiles of approved quality, colour and design joint free of size 305x305x6 mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (one cement three sand) 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officers. The colour & quality of tiles should be got approved by the Executive Engineer before use on work.

Plain ceramic tiles of size 305 x305 x6 mm

Dadooing the walls with glazed tiles of printed design of best approved quality and colour in all shade of the glazed tiles in all floor over a base layer in cement mortar 1: 2, (one cement two sand) 10mm thick and laid in situ true alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 to suit the colour of the tiles fixed in position without any air gap in the tiles neatly etc., complete complying with standard specification and as directed by the Departmental officers. The colour & quality of tiles should be got approved by the Executive Engineer before use on work.

Plain colour glazed tiles of size 150mmx150mmx6mm

Manufacturing, supplying and fixing Precast Reinforced Cement concrete slabs of following thickness in RCC 1:2:4 (One cement, two sand and four aggregates) using following 10-12mm HBGs jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed.

50mm thick slab (using 20mm HBGs jelly)

Paving the Top of roof with Solar refelective ceramic tiles of size 305 x 305 x 7mm thick of approved quality and colour laid in Cement mortar 1:3 (One cement and three crushed stone sand) 12mm thick and pointed with tile grout (Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works)

Supply and fixing fine polished cuddapah slab of following thickness for cup-board arrangements including laying to correct alignment with necessary cement mortar and black powder etc., complete complying with standard specification and as direct.

20/30mm thick

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Two coat of Enamel Paint for 10 m2

Painting the walls with Two coats with first class quality Plastic Emulsion paint of approved colour over a priming coat including thorough scraping, clean removal of dirt. The rate includes cost of brushes, sand paper, plaster of parries, putty wherever required and neat finishing etc., complete complying with standard specification and as directed by the Departmental Officer (the colour and quality should be got approved by the Executive Engineer before use)

Manufacturing, Supplying and fixing of Stainless Steel Hand rails for staricase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2.Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 x 100 x 6mm Ms base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Supply and fixing PVC rain water down fall pipes of 110 mm dia size 4 Kg/cm2 with necessary shoes, specials, clamps, bends, cowl, screws, nails, teakwood block, etc., complete complying with standard specification and as directed by the Departmental officers.

Rate for 1 RM/ One Floor

Fabricating and supplying and erecting the required number of trusses with structural steel members like angle iron MS plates for all truss members including cleats to receive the purlines all cutting drilling holes welding and fixing of members with necessary bolts nuts anchor bolt of approved quality hoisitn aligning and glazing the trusses inposition as per plan. The rate should include the cost painting the members with one coat of red oxide primer and zinc chromate etc., complete complying with standard specification and an directed by the departmental officers.

Fabricating and supplying and erecting the main gate / Wicket Gate / grill with necessary bolts and nuts including with one coat of red oxide primer and zinc chromate etc., complete complying with standard specification and an directed by the departmental officers.

Pre-painted galvanized iron fixed louvered ventilators with glass and grill: Providing and fixing louvered ventilator fabricated from roll formed sections made of galvanized steel colour coated / powder coated (Base steel as per IS 513 'D' quality, galvanized as per IS 277 with zinc of 120 grams / sqm.) with total coated thickness of 0.58mm. Paint specification: Coated sections should be with primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns. Dimensions of sections: The section for external frame should be of 57mm x 33mm. Fixing details: The section should be cut to length, joined with profile to profile component. Accessories: Glass holding flanges made of glass filled nylon. Glass: Louvers should be provided with 4mm pinhead glass. Grill: Ventilator should be provided with grill made of 10mm Square MS bars to 12mm x 5mm flat at 4" intervals. Total grill unit should be powder coated and fixed to ventilator frame with screws. The above frames should be fixed to brick / concrete masonry walls and floor by means of self-expanding screws.

Manufacturing, supplying and fixing of steel doors with the following specification M.S angles of a size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32x6mm M.S. flat is provided at required intervals in the shutter frames 18 gauge C.R. sheet is laid as panel in the shutter and welded intact for 1/3 bottom portion of the shutter. M.S. flat 18x5mm is welded over the 32x6mm M.S. flat sand witching the CR sheet in between. Additional stiffener with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter. The balance 2/3 portion at top is provided with grill at an average weight of 20kg/sq.m and 6 Nos hinges for double leaves shutter to be provided 6nos of holdfasts 120mm in length made of angle section spliced at the ends are welded to the outer frame of the door. Tower bolts 2nos. one at top and the other at the bottom arte provided one aldrop is provided at on appropriate place in the door. A Tie bar is provided at the bottom of the outer frame to prevent twisting of frame during transportation or fixing. All members are given one coat of red oxide primer as directed by the departmental officers. The rate includes cost of all meterials, labour charges,taxes, transportation to site of work , loading, unloading and all other incidental charges etc.,complete.

Double leaf

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multichambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing Solid PVC door shutters using 19 guage 19mm M.S. square tubes for styles and outer PVC frames, 15mm M.S. tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for paneling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm.The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter solid panel PVC door with frame

Solid panel PVC door with frame

Construction of inspection chamber of size 60 cm x 60 cm x 60 cm with 75mm thick RCC loose slabs covering in C.M. 1:2:4 mix including necessary reinforcement and earth work excavation for foundation wth 23 cm thick concrete bed using 40mm B.J. concrete in CC 1:4:10 for foundation brick work in CM 1:6 for chamber as directed during the execution including plastering with CM 1:3, 12mm thick, benching and channelly etc complete for 1 No.

Supplying and fixing 110mm diametre PVC VENTILATING SHAFT 3.00 M height with P.V.C Cylinderical Cowl of 110mm diametre of approved quality and make including providing leakproof joint ,wire mesh fixing with required materials etc., complete as directed by the departmental officers.

Supplying and laying of Galvolume sheet 0.47 mm thick of approved quality for roofing with necessary U or J bolts and unts bitumen GI washers etc., complete complying with standard specification. (Observed Data )

Supplying and fixing of PVC WATER TANK of best and approved quality with ISI specification and having inlet,outlet, overflow and clearing pipe arrangements and labour charges for fixing in position with all necessary accessories and transporting at site of work etc., complete complying as directed by the departmental officers.

1000 Litre

Supplying and fixing door shutters for Medium Density Fibre board of exterior grade, Both side Pre laminated including external lipping with Kiln dried soft wood of 35mm thick conforming to IS 12406 / 1989 with necessary adhesive and C.P. screws, including fixing of aldrops, tower bolts, hinges and lock strike plates, putty, fevical, varnish for T.W. lipping with thinner colouring agent etc., The rate includes cost of materials and cost for aluminium furniture fittings such as 3 nos Alu. hinges 125mm, 1 no Alu. aldrop 250 x 16mm, 1no Alu. tower bolt of 300x12mm and 1 no Alu. tower bolt of 200x12mm, 2 Nos Alu. Handles, 1 no door stopper with rubber bush incase of Single leaf door inclusive of labour charges for fixing in position etc., complete. All Aluminium furniture fittings are to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1968 for anodic film thickness of not less than 15 microns, The rate is inclusive cost of fevical and fixing charges, transportation, loading, unloading and all other incidential charges, handling charges etc., complete complying with standard specification.

Supplying and fixing inposition CRCA Pressed Steel Door Frame as per IS 4351/1976 of size 105 x 60mm with 35 x 12mm rebate on all sides with 1.25mm thick (18 gauge) sheet frames special profile extruded section including bottom tie hold faste at appropriate places and provision to fix aldrops tower bolts hinges and lock strike plate etc. The door frame inner shall be packed with CC 1:2:4 using 12mm guage HBG stone jelly including fixing the door frames inposition and dimantling the masonry and concrete wherever necessary and redoing the same original condition after fixing including scaffolding charges and labour charges and door frame will be given one coat of red oxide primer, etc., complete complying with standard specification. The rate shall inclusive of all materials, labour, transportation, loading, unloading, handling, charges etc. The sample of materials should be got approved by the Executive Engineer before use on works.

Supplying, laying and joining the following size of CPVC pipes (Internal ) of approved quality and best verity conforming to ISS and with ISI Mark laid properly to alignment including cutting, threading and fixing CPVC specials but excluding the cost of such specials and fixing to the wall with necessary TW plugs, CPVC clamps and screws, making holes on the wall or drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work, concrete and plastering wherever necessary with necessary scaffolding charges etc., complete.

Supplying, laying and joining UPVC pipes of approved quality and best variety conforming to ISS with ISI mark, of the following size External above ground level up to 4 M hight laid properly to alignment including cutting, threading and fixing the required UPVC specials but excluding the cost of such specials and fixing to the wall with necessary TW plugs, clamps and screws, making holes on the wall or drilling holes in the roof and making good dismantled portion to original condition with necessary brick work, concrete and plastering wherever necessary with necessary scaffolding charges etc., complete.

External Above Ground Level

Supplying, laying and joining UPVC pipes of approved quality and best variety conforming to ISS with ISI mark, of the following size External below ground level laid properly to alignment including cutting, threading and fixing the required UPVC specials but excluding the cost of such specials etc., complete.

External Below Ground Level

Supply and fixing in position best quality PVC Soil/ waste pipes of various size having ISI mark and providing leak proof joints including fixing to the wall with special PVC /MS clamps, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever necessary and making good the dismantled portion to the original condition, complying with standard specification etc., complete. - Above Ground level

Supply and fixing in position best quality PVC Soil/ waste pipes of various size having ISI mark and providing leak proof joints including fixing to the wall with special PVC /MS clamps, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever necessary and making good the dismantled portion to the original condition, complying with standard specification etc., complete. - Below Ground Level

Supplying and fixing in position first quality and approved variety gun metal Gate valve (Heavy type)/ Wheel Valve (Heavy Duty) with ISI Mark of approved quality of the following dia including cost of shellac, thread, labour charges for cutting, threading, fixing in position etc., complete complying with standard specification and as directed by the Departmental Officer for both internal and external water supply arrangements.

Gate Valve

Supplying and fixing in position 15 mm dia Brass Chromium Plated Screw down tap (Heavy type) / Pillar tap / Stop Cock of approved make conforming to IS specification and quality including cost of shellac, thread, cutting and threading wherever necessary etc., complete complying with standard specification and as directed by the Departmental officers. (Taps should be got approved by the Executive Engineer before use on the works)

Screw down tap (Heavy type)

Stop Cock

Two Way Blb Cock with Health Faucet

Supplying and fixing in position mirror of required size and 5.5 mm thick of approved quality and brand of size with necessary plastic back, PVC frame with bottom stand of approved color with brass screws, rowel plugs etc., complete complying with standard specification and as directed by the Departmental officers. The quality of mirror should be got approved by the Executive Engineer before use on work.

Supplying and fixing CP/ Aluminium towel rail 600mm long and 20mm diameter with brackets of same materials including cost of teak wood plug and CP screws etc., complete complying with standard specification and as directed by the Departmental officers.

CP Rail

Supplying and fixing new one of best approved quality Porcelain soap tray of size 150 x 100 mm / Porcelain soap dish of size 150x150x 50mm including cost of rowel plug, brass screws etc., complete complying with standard specification and as directed by the Departmental officers.

Porcelain soap dish of size 150x150x 50mm

CP Soap Tray 150 x 100

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550x400mm with a pair of cast iron brackets, including cost of 15mm dia metre brass chromium plated pillar tap, 32mm dia metre G. M. Wheel valve, 15mm dia brass nipple 15mm dia nylon connection etc. including fixing the wash hand basin in the wall in position with pair of CI brackets with teak wood plugs and screws and giving necessary water supply connection and painting the brackets with two coats of paint over a priming coat of anticorrosive paint including testing for leakage etc. complete complying with standard specification. The quality and colour of wash hand basin and specials should be got approved by the Executive Engineer before use on work.)

Without Pedestal

white

Supplying and fixing in position best quality cuddapah sink of following sizes including cost of 32mm dia CP waste coupling, 32mm dia PVC waste pipe with rubber plug and chain, 15mm dia brass nipple including fixing the sink in position and testing for leakages etc., complete complying with standard specifications excluding CI brackets. [The sink and specials should be got approved by the Executive Engineer before use on works]

Cudappa slab sink

Supplying and fixing in position CP shower rose with stop cock arrangements of size 15mm dia inlet and 100mm dia out let to the pipe line with necessary cutting, joining with shellac etc., complete complying with standard specification and as directed by the Departmental officers.

Supplying and fixing in position Indian water closet Oriya type of size 580x440mm white glazed earthen ware of approved quality with ‘P’ trap or ‘S’ trap conforming to IS: 2556-part XII with sand cushion and forming flooring all-round the closet using 40mm broken brick jelly in lime concrete 1:2:5(one part of lime, two parts of sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to PVC pipes by dismantling brick masonry, reinforced cement concrete roof/ floor slab and making good the dismantled portion to original condition without leakage etc. complete complying with standard specification and as directed by the departmental officers (The water closet should be got approved by the Executive Engineer before use on work.)

White

Supplying and fixing in position white glazed European water closet with P or S trap and double flapped seat cover, 10 litter capacity low level flushing tank including all internal fittings on CI brackets, 12mm brass nipple, chromium plated brown headed stop cock, 12mm nylon connection connecting with walls and floors including dismantling masonry and redoing the same to the original condition etc., complete complying with standard specification and as directed by the Departmental officers.

10 Litres - White

Supplying and fixing in position of Indian make white glazed earthen ware lipped mouth flat back urinal of best approved quality with GI connection of suitable length 32mm bell mouth PVC connection 15mm dia GM wheel wall fixing the urinal in the wall position with necessary TW plug, clamps, screws, shellac etc., including the dismantling the masonry if necessary and redoing the same to its original condition fixing the 15mm dia GI pipe and wheel wall painting the pipe two coats of approved colour of synthetic enamel paint over one coat of primer and etc., and checked without leakage etc complete complying with standard specifications and as directed by Departmental Officers.

White

Supplying and fixing of White Marble partition slab for Urinals of 1200 x 600mm size fixing to wall using 3 nos. of suitable C.P brackets with C.P bolts, nuts, washers, cutting to the shape, polshing to all the exposed surfaces abd edge grinding etc. complete as directed by the dapartmental officers- 0.72 m2

Supplying and fixing in position Cast Iron Nahini /Floor trap with Stainless steel grating /PVC nahini /Floor Trap with PVC Grating type of size 100x75/75x50 mm with best quality gratings of approved brand fixed over a bed of brick jelly lime concrete 1:2:5(One lime two sand and five aggregate) brick jelly 40mm and finishing with CM 1:3(One cement and three sand) including dismantling masonry wherever found necessary and making good to the original condition and giving connections to the cast iron pipes etc., complete complying with standard specification and as directed by the Departmental Officer

CI / Stainless Steel

Supplying and fixing in position of the following PVC specials of heavy type and approved quality and good variety excluding fixing charges complying with standard specification. Fixing charges included in the pipe laying work (The PVC specials should be got approved by the Executive Engineer concerned before use on works).

PVC specials for Sanitary arrangements

Elbow

90mm dia

110mm dia

Door Elbow

90mm dia

110mm dia

90mm dia

110mm dia

Tee with Door (Single)

90mm dia

110mm dia

90mm dia

110mm dia

Vent Cowl

110mm dia

Supplying and fixing in position of the following UPVC specials of heavy type and approved quality and good variety excluding fixing charges complying with standard specification. Fixing charges included in the pipe laying work (The UPVC specials should be got approved by the Executive Engineer concerned before use on works).

UPVC specials

Elbow

32mm dia

32mm dia

Union

32mm dia

25mm dia

Coupler

32mm dia

Reducer

32mmx25mm dia

25mm x20mm dia

Hex Nipple

32mm dia

Supplying and fixing in position of the following CPVC specials of heavy type and approved quality and good variety excluding fixing charges complying with standard specification. Fixing charges included in the pipe laying work (The CPVC specials should be got approved by the Executive Engineer concerned before use on works).

CPVC specials

Elbow

25mm dia

20mm dia

25mm dia

20mm dia

25mm dia

20mm dia

Coupling

25mm dia

20mm dia

Union

25mm dia

20mm dia

Nipple

25mm dia

20mm dia

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection (SD 76)

Supply and fixing of WT bulk head fitting with guard (Philips / Bajaj / Crompton / K. Lite) suitable for11W CFL lamp with CFL. (SD 83)

Supply and fixing of single box type 4'40 W flu fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting (SD 88)

Supply and fixing of 300 mm (12") sweep (light duty) AC exhaust fan complete without provision of hole in the wall (SD 115)

Supply and fixing of 450 mm( l8") sweep (light duty) AC Exhaust fan complete without provision of hole in the wall (SD 119)

Supply and fixing of louvers shutters arrangements for 300 mm (12") sweep (light duty) AC exhaust fan. (SD 120)

Supply and fixng of TNEB Meter Board suitable for 3 Phases 100A service connection made up of suitable angle iron frame work of size 2 feet x 1 1/2 feet using angle iron of size 1 1/2" x 1 1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1 1/2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos 100A fuse units (500V) 1 No. Neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 7/16 PVC insulated copper wire with earth connection complete (SD 130)

Supply and fixing of 20Amps DP Plug and Socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug) [Legrand (MDS) / Hager (L&T) make] (SD 140)

Supply and fixing of 100 Amps TPN sheet double break switch with HRC fuse and neutral on suitable angle iron frame work with earth connection only (SD 169)

Supply and frxing of brass cable gland for 3 1/2x50 sqmm PVC armoured LTUG cable with earth connection (SD 188)

Supply and clarnping of 3-1/2 x 50 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps . Same as SD 209, except 3-1/2 x 50 sq.mm. PVC LTUG armoured cable (SD 224)

Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry (SD 233)

Supply and providing cable end termination of 3 1/2 x 50 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete(SD 237)

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) ( 5 points / Coil) Lower End SD 318

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) ( 6 points / Coil) Lower End SD 320

Wiring with 3 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point Lower End. SD 356

Wiring with 2 x 4 sq.mm. (56/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitablePVC rigid pipe Concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 16A one way module switch and 1 no. 16A 3/2 pin module socket with module front plate with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with painting of suitable colour for Concealed PVC pipe power Plug point ( 8 points / Coil) Lower End SD 396

Supply and Run of 2 of 2.5 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour.

Supply and Run of 2 of 4 sq.mm. (56/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour. SD 430

Supply and Run of 4 of 10 sq.mm. (140/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm. PVC insulated SC unsheathed copper wire with painting of suitable colour. SD 444

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection SD 458

Supply and fixing of 1 no.6A two module socket , 1 no. 6/16A two module socket , 1no. 6A one module switch, 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box ( GI ) in flush with wall with connections. Lower End SD 513

supply and fixing of 30W LED street light fitting with LED (Lower end) with 25mm dia. GI pipe (class B) with 1 no.25mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting . SD 534

supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Lower end) with 300mm down rod on the existing fan clamp SD 582

Supply and fixing of 6 way Horizontal Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 18 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Lower End SD 635

Supply and fixing of 8 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 3 nos. 32A 3P MCB , 15 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Lower End SD 671

Supply and fixing of 6 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board (with MCCB incomer) with double door (metal door) with 1 no. 160A 4P MCCB switch as incoming and 4 nos.63A 3P MCB , 6 nos. 6A to 32A SP MCB as outgoing with suitable cable end box on suitable angle iron frame on wall with earth connection only. Higher End SD 695

Supply and Laying of 3 1/2 x 50 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. SD 748

Supply and delivery of MS Kiosk of size 0.75mx0.45mx0.75m made up of MS angle of size 50mmx50mmx4mm alround covered with 16 gauge MS sheet and kiosk door made up of MS plates of size 25mmx3mm including cutting, welding, grinding, locking arrangements and labour charges etc.

Subtotal

KMC Associates, Theni

VKS INFRATEC PROJECTS