8377/E8

Amount

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, in roof covering including ridges and keeping serviceable sheets in safe custody for reuse in the work complete as directed.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete as directed.

Taking down old unserviceable existing roof membrane with concrete padding and screed bedding and removing the debris from site etc complete all as directed by Engineer-in-Charge.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets etc complete all as directed by Engineer-in-Charge.

Dismantling Timber scantling 40 Sqmcm and over in section in unframed work etc complete all as directed by Engineer-in-Charge.

Dismantling of timber fillets, rails, posts, rafters, purlins etc under 40 Sqcm in section complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Demolition of plain cement concrete (unreinforced) in ground floors and pavings not exceeding 15 Cm thickness. (below or above ground level) complete all as specified and directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons, laid, bedded and pointed in cement mortar etc complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Taking up or down steel water tubing 15mm bore with connection complete all as specified and as directed.

Taking up or down steel water tubing 20mm bore with connection complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed

Taking down chowkats or frame, n.exc 1.5 Sqm each with shutters (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frames, exe 1.5 but n.exc. 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down shutters of any description n. exc 1 Sqm each complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm but n.exc 2 Sqm each complete all as specified and directed.

Materials and labour Anti Termite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed.

Materials and labour Anti Termite Treatment of voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed.

Materials and labour Anti Termite Treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed.

Material and Labour Plain cement concrete 1:2:4, type B-0 (using 12.5mm graded crushed stone aggregate) as in padding, benching and filleting complete all as specified and directed.

Material and Labour Reinforced cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Material and Labour for plain cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) for embedding holdfast, bed block, cills, etc including necessary form work complete all as specified and directed.

Material and Labour Brick work with fly ash pulverized bricks of designation 7.5, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directeded.

Material and Labour Brick work with fly ash pulverized bricks of designation 7.5, as in half brick thick wall, straight or curved on plan any radius radius, built in cement mortar 1:4 complete all as specified and directeded.

Materials and Labour Formwork to soffits of suspended slabs such as roof slabs,floor,slabs,landings and similar work not exceeding 200mm thick rough finished surfaces without using extra cement(Horizontal or slooping ) complete all as specified and as directed.

Supply and fix Well seasoned 2nd class hard wood scantling, clean swan timber in unframed work complete all as specified and as directed.

All as per item No.29 here in before but except timber ( Old serviceable timber obtained from dismantling shall be reused).

Supply and fix Well seasoned 2nd class hard wood Plain fillets of section exc 6 Sqcm but n.exc 13 Sqcm in square, rectangular or triangular in section, clean sawn, secured with nails or brads complete all as specified and as directed.

Supply and fix 2nd class hardwood plain solid straigth chowkhat and frame wrought frames rebated on the solid rounded or chemferded put together with glue pinned at joints complete all as specified and directed complete all as specified and as directed.

Supply and fix Pressed steel frames of size 105mm x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed. Note:- Pressed steel frame shall be filled with PCC type C0 ( 1:3:6, using 12.5mm graded crushed stone aggregates) and cost of same shall deemed to be included in the rate quoted by the tenderer in this Item.

Supply and fix Pressed steel frames of size 125mm x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed. Note:- Pressed steel frame shall be filled with PCC type C0 ( 1:3:6, using 12.5mm graded crushed stone aggregates) and cost of same shall deemed to be included in the rate quoted by the tenderer in this Item.

Supply and fix 2nd class hard Wood, 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, 2009, Section 8, Clause 8.24 (a); supplied and fitted to chowkats complete all as specified & directed by the Engr-in-Charge.

All as per item No. 35 above but 30mm thick divided into sqaure with plain chamfered or rounded miteredand rebated sashbar any Nos as in window/ventilator size of member of shutter as specifieed in SSR Part-I 2009 complete all as specified.

Supply and Fix Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

Supply and fix 35 mm thick factory made flush shutter, solid core construction with particle board core and plywood face panels commercial type on both side complete all as specified and directed by Engr-in-Charge.

Supply and fix factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified & directed by the Engr-in-Charge.

Supply and Fix Factory Made Solid PVC Moulded Door Shutter With Wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site complete all as specified and directed.

Supply and fix 1.50mm thick power coated aluminium anodized , three track sliding window with three nos shutters made of aluminium section as per drawing no CWE/KOL/TD-33 of section no 1F-1F including necessary jointing cleats, glazing clips, rubber neoprene packing, roller, locking arrangement, handles 2 Nos , anodised aluminium snap beading screws etc.Complete all as specified and as directed. Notes :- (i) All window member including fitting & fixture i.e frame, track, shutter frame, etc shall be deem to included quoted rate. Only measure opening size of window. (ii) Only Glass for window & wire mesh shall be measure and paid separately under relevant items of BOQ .

Supply and fix 100mm long butt hinges stainless steel complete all as specified and as directed.

Supply and fix 200mm long stainless steel barrel tower bolts complete all as specified and as directed.

Supply and fix 150 mm long stainless steel handle complete all as specified and as directed.

Supply and Fix 300mm long stainless steel sliding door bolt with hasp, staple(bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and as directed.

Supply and fix Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aparture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

Supply and fix Two coat creosote oiling on wooden new surafces including preparation of surface of any description not otherwise described over 10 cm width or girth complete all as specified and directed .

Materials and labour Preparation of wood & wood based material, steel & iron work new or old of any description and treating the back of chowkhats etc. area tarred exc 0.1 Sqm but nexc 0.5 Sqm each complete all as specifieda and as directed.

All as per item No.48 here in before but treating small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats, etc. area n exc 0.1 Sq. m each complete all as specified and directed.

Supply and fix TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Supply and fix Stainless steel door stopper complete all as specified and directed.

Supply and fix 18/19mm thick medium density fibre board, exterior grade, fixed to timber framework with screws including taking down old unserviceable one.

Supply and fix in repairs 30mm width of flaps (when open) Continous (Piano) hinges, brass, bright finish or electrogalvanised complete all as specified and as directed.

Supply and fix in repairs 40mm dia cupboard knobs fixed with nut screws and washer of wooden finish brass polished complete all as specified and directed.

Material and Labour Mild steel Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming to Fe-410-0 Gde E-250 complete all as specified and directed.

Materials and Labor Mild steel work as in hold fast & similar small articles conforming to Fe-290 and Gde-E-165 complete all as specified and directed

Supply and fix 4mm thick E-board classic of M/s Everest or equivalent of any design placed in a grid of size 605 x 605 mm with and including aluminium powder coated angle/ tee/ channel section duly suspended with and including 4mm dia GI hanger fixed with GI hooks 4.00mm dia and fasteners as required including two coats of acrylic distemper complete all as specified and as directed.

Supply and fix 4mm thick plain AC bldg board fixed as in ceiling with nails complete all as specified.

Materials and labour for preparation of roof surfaces and proving roof treatment works as under:- (a) Material and Labour 10mm thick cement screed bed in CM 1:4. (b) Material and Labour for applying a coat of bituminous primer @ 0.40 ltr/Sqm and allow to dry. (c) Supply and laying APP membrane 3mm thick (minimum), weighing 3.6 Kg/m² reinforced with polyster non woven fabric (weighing not less than 160 gms/Sqm) shall be applied by butane torch application and sealing all joints etc. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction complete all as specified and as directed. (d) Two coats of Bitumen based UV reflective paint with aluminium finish over APP memebrane.

Supply and fix 6mm thick asbestos cement corrugated, or semi-corrugated sheet in roof, wall etc. fixed with "J" & "L" type hooks complete all as specified and directed

All as item No. 60 but except sheet (old serviceble sheet obtained from item No. 02 shall be reused).

Supply and fix AC two piece adjustable plain wing ridges 6mm thick for corrugated sheet fixed with "J" or "L" type hooks complete all as specified and directed

Supply and fix 0.63mm Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) grade of zinc coating 275, fixed with 'J' or 'L' type hooks complete all as specified and directed.

Supply and fix PVC corrugated sheeting 2 mm thick in roof fixed with 'L' type or 'J' type or cranked hook bolts complete all as specified and directed

Supply and fix Pre-Painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Material and Labour for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in paving and plinth proction laid in panels etc finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed. Note:- Construction joints will be provided at interval of 2.5m length and filled with bitumen 80/20 mix with sand in ratio of 1:3 and cost of the same shall be deemed included in quoted rate

Material and Labour 25mm thick PCC (1:2:4) type B-0 (using 12.50mm graded crushed stone aggregates) as in sub base of floor complete all as specified.

Material and Labour 40mm thick PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregates) as in flooring laid in panels including finishing the top surfaces even and smooth without using extra cement, complete all as specified.

Supply and fix Glass dividing strips, 38mm width and 3 mm thick and ditto, complete all as specified.

Materials and labour Double Charged Light shade Vitrefied ceramic tiles 8-10mm thick (Square/Rectangular) polished, area of each tiles upto & including 0.36 Sqm in floors, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

Materials and labour Double Charged Light shade Vitrefied ceramic tiles 8-10mm thick (Square/Rectangular) polished, area of each tiles upto & including 0.36 Sqm as in vertical surfaces such as skirting, dado, riser to stepts etc , set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick backing course in CM 1:3 complete all as specified and directed.

Materials and labour for non-skid, ceramic, coloured joint free tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.18 Sqm but n.exc 0.38 Sqm, in floors etc, including 15 mm thick screed bed in cement mortor 1:6 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed by Engineer-in-Charge.

All as per item No.72.00 here-in-before but on vertical surfaces such as skirtings, dados, risers etc over and including 10mm thick backing course in CM 1:4 complete all as specified and directed.

Materials and labour for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 Sqm but n.exc 0.18 Sqm, in floors etc, including 15 mm thick screed bed in cement mortor 1:6 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed by Engineer-in-Charge.

All as per item No.74.00 here-in-before but on vertical surfaces such as skirtings, dados, risers etc over and including 10mm thick backing course in CM 1:4 complete all as specified and directed.

Materials and labour for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.06 Sqm but n.exc 0.11 Sqm, in floors etc, including 15 mm thick screed bed in cement mortor 1:6 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed by Engineer-in-Charge.

Materials and labour Glazed ceramic colour tiles in vertical surfaces such as skirtings, dados, risers etc of size 300 x 200 x 6-7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement ot match the tiles over and including 10mm thick backing course in CM 1:4 for receiving tiles.

Materials and labour Glazed ceramic colour tiles in vertical surfaces such as skirtings, dados, risers etc of size 450 x 300 x 6-7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement ot match the tiles over and including 10mm thick backing course in CM 1:4 for receiving tiles.

Material and Labour 16-18mm thick granite(of any type) work (table rubbed and polished) in kitchen cooking platform and like in CM(1:4) incl pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm thick screed bed in CM 1:4 including necessary edge moulding/chamfering (full or half moulding) complete all as specified and directed.

Material and Labour Rendering 15mm (10 + 5 mm) thick in cement mortar 1:4 on fair faces of brick work or concrete surface in two layers each mixed with integral water proofing compound @ 2% by weight of cement (WPC shall be mixed with top layer only i.e 5mm thick) finished the surfaces even and smooth without using extra cement complete all specified and as directed. Note : - Water proofing compound shall be measured and paid separately as "Supply only" item under relevant item of these schedule.

Material and Labour Rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished the surfaces even and smooth without using extra cement complete all as specified and directed.

Material and Labour Rendering 5 mm thick in cement mortor 1:3 on concrete surfaces as in ceilings (sunshed, chajja etc) and finishing surfaces even and smooth without using extra cement complete all as specified and directed.

Material and Labour Applying polymer modified cement mortar rendering 20mm thick in CM 1:3 on wall duly mixing polymer modifier "Nitobond SBR of M/s fosroc Chemicals or Hind Styrene BR of M/s Hincon Chemicals Ltd or equivalent porduct of M/s Pidilite Industries" @ 7 litre per bag of cement complete all as specified and directed.

Materials and Labour Cutting out existing cracks in concrete surfaces forming grooves of 25mm x 40mm size, cleaning the groove throughly with blower, applying primer coat of mix of IPH CC Resin & Hardner in equal proportion with suitable brush to form a film on the surface of groove, filling the groove with putty made by mixing IPH CC Resin, Hardner and admixure in the proportion of 1:1:4 and finally applying the sealing coat of same mix and in the manner primer coat is applied with following min coverage per Running Metre length of groove complete all as directed by Engineer-in-Charge. Materials Priming Coat Putty Filling Seal Coat Resin 60 gms 100 gms 40 gms Hardner 60 gms 100 gms 40 gms Admixure - 400 gms - Make of materials :- Fosroc / Hindcon Chemicals Ltd / Sika / STP.

Materials and Labour Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing , etc, and making good, cutting not exc 10 Cm girth complete all as specified and as directed.

"Supply only" integral water proofing compound (ISI marked) complete all as specified and directed. Make:- STP NO 1/ PEDILITE(DR FIXIT)/ FOSROC/ CICO/ SIKA

Materials and labour Preparation of old plastered wall surfaces and applying one coat of white wash complete all as specified and directed.

Materials and labour Preparation of old plastered wall surfaces and applying one coat of Acrylic distemper of any colour / tint complete all as specified and directed.

Materials and labour Preparation of old plastered Ceiling surfaces and applying one coat of Acrylic distemper of any colour / tint complete all as specified and directed.

Materials and labour Preparation of newly plastered wall surfaces and applying two coats of Acrylic distemper of any colour / tint over a coat of primer including one coat of white cement based putty complete all as specified and directed.

Materials and labour Preparation of newly plastered Ceiling surfaces and applying two coats of Acrylic distemper of any colour / tint over a coat of primer including one coat of white cement based putty complete all as specified and directed.

Materials and labour Preparation of newly plastered external surfaces of any description and applying Premium Acrylic smooth exterior paint with silicon additives of required shade complete all as specified and directed. Note:- For new works Two or more coats applied @ 1.43 litre/ 10 Sqm area over and including Priming coat of exterior primer applied @ 2.20 Kg/ 10 Sqm.

Materials and labour Complete removal of existing treatment from old external surfaces and applying Premium Acrylic smooth exterior paint with silicon additives of required shade complete all as specified and directed. Note:- For new works Two or more coats applied @ 1.43 litre/ 10 Sqm area over and including Priming coat of exterior primer applied @ 2.20 Kg/ 10 Sqm.

Materials and labour Preparation of old plastered external surfaces of any description and applying one coat of Premium Acrylic smooth exterior paint with silicon additives complete all as specified and directed.

Materials and labour Preparation of old plastered external surfaces of any description and applying one coat of Cement based paint of any colour / tint complete all as specified and directed.

Supply and fix 4mm thick sheet glass, glass, ordinary quality and glazing with oil putty in square n.exc 0.5 Sq m in each pane complete all as specified and directed including hacking out old unserviceable broken glass.

Supply and fix 4mm thick frosted glass, glass, ordinary quality and glazing with oil putty in square n exc 0.5 Sq. m in each pane complete all as specified and directed including hacking out old unserviceable broken glass.

Supply and fix Tinted sheet glass 4.80mm thick , pin head type and glazing in squares exc 0.5 Sq. m in each pane complete all as specified and as directed.

Material and Labour Preparation of new steel surfaces of any description, over 10 Cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint of any colour / tint over a coat of red oxide primer complete all as specified and directed.

Material and Labour Preparation of old steel surfaces of any description, over 10 Cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint of any colour / tint over complete all as specified and directed.

Material and Labour Synthetic enamel paint of any colour / tint, two coats over a coat of pink primer over girth exc 10 Cm on new wood or wood based surfaces after necessary preparation of surfaces complete all as specified and directed.

Material and Labour Synthetic enamel paint of any colour / tint, one coat over girth exc 10 Cm on old wood or wood based surfaces after necessary preparation of surfaces complete all as specified and directed.

Supply and fix 20mm outer diameter of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls / ceilings or laid in floors complete all as specified and as directed .

Supply and fix 25mm outer diameter of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls / ceilings or laid in floors complete all as specified and as directed .

Supply and fix 110 mm bore, PVC (SWR) pipe, single socketed, in any length with rubber ring joints fixed to wall etc complete all as specified and directed including taking down old unserviceable PVC(SWR) pipe with unserviceable fittings.

Supply and fix 110 mm bore, PVC (SWR) pipe, double socketed, in any length with rubber ring joints fixed to wall etc complete all as specified and directed including taking down old unserviceable PVC(SWR) pipe with unserviceable fittings.

Supply and fix 110 mm bore, PVC (SWR) bends with access door of any radius complete all as specified and directed.

Supply and fix 110 mm bore, PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and directed.

Supply and fix in repairs UPVC (SWR) floor trap 75mm bore dia of outlet, plain with grating including jointing with solvent cement complete all as specified and directed.

Supply and fix in repair 15mm Bib Taps, fancy type, CP, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. Make : Essco Cat No. MQT -511KN or equivalent model from make as specified in Particular specifications.

Supply and fix in repair 15mm Bib Taps long body, fancy type, CP, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. Make : Essco Cat No. MQT -512KN or equivalent model from make as specified in Particular specifications.

Supply and fix in repair 15mm Bib Taps, fancy type, CP, cast copper alloy two in one tap with Wall Flange screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. Make : Essco Cat No. MQT -512ANKN or equivalent model from make as specified in Particular specifications.

Supply & fix in repair 15mm Pillar Taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with or without lettered "Hot" or "Cold" with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed. Make : Essco Cat No. MQT 508KN or equivalent model from make as specified in Particular specifications.

Supply & fix in repair ABS body chrome plated shower rose 125mm size including fixing to steel pipe or union complete all as specified and as directed. Make : Essco Cat No. EOS 542A or equivalent model from make as specified in Particular specifications.

Supply & fix in repairs shower arm 240mm long round shape with flage including fixing to steel pipe or union complete all as specified and as directed. Make : Essco Cat No. ALE 536A or equivalent model from make as specified in Particular specifications.

Supply & fix in repairs 15mm bore brass chromium plated Angular Valve with Wall Flange complete all as specified and as directed. Make : Essco Cat No. MQT 526NKN or equivalent model from make as specified in Particular specifications.

Supply & fix in repairs 15mm bore brass chromium plated two way Angular Valve with Wall Flange complete all as specified and as directed. Make : Essco Cat No. MQT 526AFKN or equivalent model from make as specified in Particular specifications.

Supply & fix in repairs Chromium plated Health faucet with 8mm Dia, 1.2 Metre long flexible tube and wall hook with N.R.V (Back Flow Preventer) complete all as specified and as directed. Make : Essco Cat No. ALE ESS 583 or equivalent model from make as specified in Particular specifications.

Supply and fix in repairs Bip tap with nozzle 15mm bore standard of PTMT any colour screwed for iron pipe & fixed complete all as specified and directed. Make : Shakti cat part no. SB-FR-121 or equivalent model from make:- Prayag / Polytuf.

Supply and fix in repairs Pillar taps fancy type15mm bore of PTMT any colour screwed for iron pipe & fixed. complete all as specified and directed Make :Shakti cat part no. SB-FR-130 or equivalent model from make:- Prayag / Polytuf.

Supply and fix in repairs Angle stop valve 15mm bore of PTMT any colour screwed for iron pipe & fixed. with PTMT flange complete all as specified and directed. Make :Shakti cat part no. SD-DM-144 or equivalent model from make:- Prayag / Polytuf.

Supply & fix in repair 15mm bore stop cock, cast copper alloy, chromium plated , screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. Make :Essco Cat Part No. MQT 513AKN or equivalent in Prayag/Jaquar .

Supply and fixing in repair 10 litre capacity low level PVC flushing cistern (any colour), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete as directed. Make : Cera Model No B1010107 or equivalent model of make as specified in Particular Specification.

Supply and fix 560x430 mm size vitreous china wash basin white including 32 mm waste coupling of PTMT (half or full threaded, minimum weight 45 gms), waste pipe low density polyethylene pipe 32mm bore and brackets including taking down old wash hand basin alongwith fittings all as specified and as directed. Make:- Cera Cat Part No. S2040108 or equivalent of approved make as specified in Particular specification.

Supply and fix in replacement Vitreous China squatting pan of ‘Orissa pattern’, size 580 mm x 440mm (white) with ‘P’ or ‘S’ trap, front or back inlet and foot rests, any pattern complete including provision of PCC bedding and connection to trap, and to flushing pipe, antisyphonage pipe, etc. complete including making good to floor all as specified and directed by the Engr-in-Charge. Make : Hindware Cat No 20042 equivalent of approved make in Jaguar, Cera, Prayag.

Supply and fix in repairs Vitreous China wash down water closet pan (ISI Marked, Ist Quality) including 'P' or 'S' trap (pedestal pattern), Snow white or in matching colour of tiles (excluding flushing cistern and flush pipe) including plastic water closet seat, white or in matching colour , closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device and wash down water closet complete all as specified and as directed. Make : Cera Cat part No.Cat. No. S1053101 'S' Trap or equivalent model of make as specified in particular specifications.

Supply and fix repairs Plastic water closet seat cover, white with recessed bottom with PVC hinging device complete all as specified andas directed. Make : Prayag/ Shakti/ Cera/ Commander.

S&F Rotational moulded HDPE water storage tanks of 500 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position,tripple layered ISI marked complete, screwed for iron pipe or brass ferrule including 25mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed complete all as specified and directed including taking down old unserviceable tank with ball cock. Make:- Sintex/ Polycon and Make of Ball cock:- Prayag/ Polytuf.

S&F Rotational moulded HDPE water storage tanks of 1000 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position,tripple layered ISI marked complete, screwed for iron pipe or brass ferrule including 25mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed complete all as specified and directed including taking down old unserviceable tank with ball cock. Make:- Sintex/ Polycon and Make of Ball cock:- Prayag/ Polytuf.

Supply and fix in repair PTMT connection 600 mm long fixed to 15mm GI pipe complete all as specified and directed. Make- Prayag/ Polytuf/ Shakti.

Supply and fix in repair 15mm bore dia of pipe Ball valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed. Make : Prayag/Shakti/Polytuf .

Supply and fix in repair 20mm bore dia of pipe Ball valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed. Make : Prayag/Shakti/Polytuf .

Supply and fix in repair 25mm bore dia of pipe Ball valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed. Make : Prayag/Shakti/Polytuf .

JOY RAM ENTERPRISE

K.P Construction Co

MS JYOTI INDUSTRIES

MS HORIZEN

S KUNDU AND CO

INDIA ELECTRICAL EQUIPMENTS