Provision of (i)Dual Detection by Commissioning of Track circuit in Joint Line between RKSN-RKSN West/Outer. (ii)Auto Media Change over System for SSDACs & UFSBI over Chakradharpur Division.

A-Execution(SOR) for (Dual Detection by Commissioning of T/Cct in

B-Material Supply(SOR) for (Dual Detection by Commissioning of T/Cct

C-Execution(SOR) for (Auto Media Change over system for SSDACs &

D-Material Supply(SOR) for (Auto Media Change over system for

D1-Material Supply(Non-SOR) for (Auto Media Change over system for

Item- 1 Details of Schedule 'A' are given below: -

S No. Item Description of Item Unit Qty Rate Amount

1 01 Excavation of trench in all kinds of soils Kilometre 1.00 79869.00 79869.00

including soft rocky area and clearing of roots

of trees, rocks, bushes, ballast &

reconditioning etc., including bailing out water

and disposal of extra soil including back filling

with excavated earth and ramming of

trenches after cable laying for the following

depths and widths as specified in Technical

Circular No. 2 of 1988 & 01/2010 issued by

CSTE/SER or any other latest guidelines. Note:

In case, trenches are other than prescribed

depth & width, Proportionate payment shall

be released. (i) Depth 1.0 meter, Width 0.3

2 02 Excavation of trench in all kinds of soils Kilometre 1.00 95893.00 95893.00

including soft rocky area and clearing of roots

of trees, rocks, bushes, ballast &

reconditioning etc., including bailing out water

and disposal of extra soil including back filling

with excavated earth and ramming of

trenches after cable laying for the following

depths and widths as specified in Technical

Circular No. 2 of 1988 & 01/2010 issued by

CSTE/SER or any other latest guidelines. Note:

In case, trenches are other than prescribed

depth & width, Proportionate payment shall

be released. (i) Depth 1.2 meter, Width 0.5

3 03 Laying of S&T Cables (Signal/Quad/Power) in Kilometre 6.00 20239.00 121434.00

the excavated trench to Drawing No.

CON/SK/T/5 or latest. Supply and

transportation of 'U' clamps, anchoring of

cable at every 10 metres interval with 'U'

clamp on trench to Drawing No. CSTE/CON

/CABLES/81 or latest. Supply, transportation,

and placing of cable demarcating led belt to

Drawing No. CON/SK/T/6 or latest punched at

an interval of 30 metres and wrapped round

each cable throughout the cable route and

also at every track/Road/ platform crossing as

above specified in Technical Circular No.

2/1988 & 01/2010 issued by CSTE/SER or as

per latest guidelines and guarding the cables.

Collecting empty drums with left over cable

and to be returned to the stores of stock

holder. Note: Cables will be meggered before

& after its laying by contractor under

supervision of Railway representative &

Contractor will submit their reports.

CKP-DIVN- S AND T/SOUTH EASTERN RLY

4 04 Transportation of cables in rolls with or Drum-Km 6.00 2328.00 13968.00

without wooden drums (S and T Cables) from

concerned store/Central Store(CKP) to the site

of works. Note: The unit Drum-KM indicates

Drum X length of cable in that drum. It

doesn't have any significance over the

distance it has to be carried for execution of

cast/cast in -situ RCC cable ducts including

top cover as per RDSO drawing No.

SDO/S&T/RCC DUCT/1018/1 & 2, dated

29.5.23 or latest. Note- The rate is inclusive of

all type of transportation including labour till

it is placed into trenches. The laying of cables

shall be paid separately fulfilling the laying

procedure as per above drawings. (Inspection

by representative of Sr. DSTE/CKP)

6 06 Excavation of trench in all kinds of soils Metre 84.00 691.00 58044.00

including soft rocky area and clearing of roots

of trees, rocks etc. to a depth of 1 metre and

width 0.3 mtr. Track/ Pucca road/Platform

crossing/ Level crossing as per SEM Drawing

No.15-D5 including supply, transportation and

laying of DWC pipes (full) with collar(for

jointing pipes) Inner diameter/Outer

diameter:103mm/120mm to Specification

No.14830 (Part-2):2001 as per SEM Drawing

No. 15-D4 and drawing of cable through DWC

pipes with collar(for jointing pipes) including

back filling and ramming after cable laying as

specified in Tech. Circular No. 2 of 1988 &

01/2010 issued by CSTE/SER for S&T Cables

or any latest guidelines. This includes

repairing and plastering of Platform/Pucca

road after cable laying.

7 07 Chase cutting and smoothening of inside Metre 20.00 146.00 2920.00

surface of sizes 80 mm deep and 170 mm

width for single/multiple cable chase in

concrete or hard rocks or platform or

cemented floor. Note: Sundries materials such

as sand, cement, etc. shall be supplied by the

contractor at site and to be inspected by

Railway Site Engineer before placing in the

chase. Note: In case, chase cutting &

smoothening are other than prescribed depth

& width, Proportionate payment shall be

CKP-DIVN- S AND T/SOUTH EASTERN RLY

8 08 Alterations/modifications works on existing Numbers 3.00 21225.00 63675.00

relay rack (Q-series/ Composite Relay

Racks)/Cable Termination Racks (CTR)

including works of installation, wiring,

termination, testing and commissioning. The

work includes fixing of aluminium/steel/M. S

ladder along with supply as per requirement

to accommodate additional plug board,

relays, terminals/blocks, terminals, tag blocks,

fuses, transformers, bus bars, TW

shelves/strips etc. in the existing relay

racks/CTR's, 6 mm Hylam sheets of required

length for writing terminal description etc.

fixing and termination of cables on the relay

racks, CTR's with number embossed ferrules,

bunching of cables with PVC tapes, earthing

of cable armours, covers including painting

and lettering, making anti tilting arrangement.

Note:- a) Relay rack (Q-series/ Composite

Relay Racks) : Payments for alterations in

existing relays upto 20 nos. relays & above 20

nos. shall be made 50% & 100% respectively.

b) Cable Termination Racks (CTR):- Payments

for alterations in existing CTR upto 120 cores

& above 120 nos. cores shall be made 50% &

100% respectively.

9 09 HDD: In case of short stretches (less than 100 Metre 150.00 1964.00 294600.00

m in single stretch) Micro Tunnelling through

Horizontal directional drilling (HDD) machine,

preparation of sites, boring and laying of

HDPE pipes of size (Outer/Inner diameter=

50mm/42mm) for crossing of S&T cable

through HDPE pipe at bridges/culverts/track

crossing/pucca road crossing. Boring trench

shall be minimum 3 (three) meter below the

surface/river bed and minimum 1 m at

track/road/pucca road crossing area etc. This

includes supply of permanently lubricated

HDPE telecom ducts of equal length as per

Specification No. RDSO/SPN/TC/45/2013

REVISION 2.0 with latest amendments. For

each HDPE duct the following items are to be

supplied as per requirement (a) End plug, (b)

Cable sealing plugs, (c) Plastic coupler slip

fit/push fit type & (d) End plugs to be provided

along with drum. In case the site doesn't

allow to perform as per schedule, written

approval must be obtained from at least site

in-charge officer. Note: The boring profile

should be recorded and submitted for

verification of depth and length of boring. (a)

(Cement: Sand: Stone chips of 25mm nominal

size) for miscellaneous works. It includes

excavation, ramming of CC by using vibrator,

curing and plastering with cement and sand

mixture (aggregate will not exceed beyond

3.8 cm). Note: All materials required for

foundation are to be supplied by the

CKP-DIVN- S AND T/SOUTH EASTERN RLY

11 11 Execution of Full Apparatus Case with earth Numbers 8.00 9147.00 73176.00

excavation for pit, concrete foundation,

surrounding earth work, erection and

installation as per Drawing No. Con/SK/T/8 or

latest and wiring to be done as per SEM

Drawing No.19-D8 or as per direction of site

engineer. Supply and fixing of Hylam sheet

strip of appropriate size of 3 mm or 6 mm as

required with hole for fixing of terminals, fuse

blocks, relay and other accessories for

signal/track circuit, termination of cable with

number embossed ferrules, bunching of

cables with PVC tape, proper soldering of

cable armour with earth catenary wire,

earthing of cable armour as required. Writing

& terminal description including Painting of

the apparatus case inside and outside after

clearing the surface thoroughly and first

coating of anticorrosive paint and subsequent

two coats of Aluminium paint outside and red

oxide inside and lettering etc. This also

includes transportation of 25 mm/12mm

Hylam sheet for shelf or as required and also

includes minor modification in L/Boxes as per

site requirement. The contractor shall supply

4 no. of foundation nuts & bolts of size 22 mm

dia. x 450 mm long with 2 flat spring washers,

with each nut & bolts, sand for filling up cable

pit inside the apparatus case including plaster

and bolts, nuts, screws, MS Clamps for fixing

equipment/cable. Note: - Part payment shall

be released after completion of- (i)

Foundation- 40%, (ii) Erection - 10%, (iii)

Wiring, earthing, testing - 20%, (iv) Painting,

writings - 10%, (v) Plastering, sand filling &

etc. - 10%, (vi) Commissioning - 10%.

12 12 Transportation, installation and charging of Numbers 6.00 405.00 2430.00

2V lead acid type Secondary Cell and

preparation of electrolyte for each cell.

Charging to be done as per OEM's instruction

with uninterrupted power supply in presence

of Railway representative. After charging, it

should be kept at the dedicated location as

per use. Note- If power is not available at site

of work, charging may be done at nearby

location as per convenience of the railway.

This includes transportation of uncharged

cells at the site of charging, supply of acid,

distilled water at the site of charging and

transportation of charged cells back to the

site of work. (a) 2 Volt 80AH.

13 13 Transportation & Fixing of insulated lead wire Numbers 16.00 921.00 14736.00

in track circuits. This includes cutting of

insulated lead wire in two pieces of required

length (one of not less than 3.5 meter. &

another not less than 1.5Mtr.) and eyelet of

suitable diameter is to be crimped at one end

of each wire. The crimped end is to be

connected to the terminals of JB and the other

end to be fixed to Rail with channel pin by

removing existing channel pin etc. Note: All

required sundry materials like channel pin,

eyelet & insulated lead wire shall be supplied

by the contractor.

14 14 Painting of Glued joints with epoxy paint Numbers 6.00 50.00 300.00

including epoxy paint supply. This includes

scraping of old paint & rusts and prima

coating followed by final painting.

CKP-DIVN- S AND T/SOUTH EASTERN RLY

15 15 Excavation of earth pit, placing & fixing of Numbers 8.00 1791.00 14328.00

Earth electrode with construction of cement

enclosure to SEM Drawing No. 19-D6 and

drawl of 6 SWG GI/Copper cable from earth

electrode to goomties/relay

room/cabin/station, etc. and drawl of MS flat

35mm x 6mm for signal post/Location box

shall be used as the case may be, including

fixing at both ends of the wire/MS flat. This

includes transportation of materials. Note 1:

Materials such as charcoals, salt, sal

ammoniac, 6 SWG GI wire, copper lugs with

Steel bolts & nuts etc. shall be supplied by

the contractor. MS flat 35mm x 6mm/Copper

cable shall be supplied by Railway. NOTE 2:

Painting of MS Flat with one coating of Red

Oxide as primer & two coating of

anticorrosive black included in Execution.

16 16 Design and supply of the following drawings Station 1.00 38738.00 38738.00

to office records as per requirement of the

Railways. This includes alteration at different

stages and finally supply of all the drawings

including tracings within 30 days or as

defined in the tender document from the date

of commissioning of the work, otherwise

penalty to be imposed as per tender

document. This includes the following

drawings for each station: (1) Cable layout

plan, (2) Cable corrage plan, (3) Location Hut

drawing, (4) Termination chart of end

goomties and location hut, (5) Traction

bonding plan, (6) Contact Analysis Chart, (7)

SWRD & GWRD, (8) Equipment Layout Plan,

(9) Power Supply arrangement diagram, (10)

Relay Disposition chart, (11) Any other

drawing as found relevant as per site

condition. Office record if online maintenance

is not implemented includes the following: (i)

Battery History book, (ii) Track Circuiting

Register, (iii) Track circuit maintenance

Register, (iv) Cable Meggering Register, (v)

Signal History Register, (vi) LED Register, (vii)

Glued joint/ Block joint Register, (viii) Point

machine Maintenance Register, (ix) Joint

Inspection Register such as P. Way, Electrical

& Signal, (x) Relay Register, (xi) Route

cancellation Register, (xii) Relay Room Key

Register, (xiii) Emergency Point operation

Register, (xiv) Crank Handle Register, (xv)

Emergency Route Cancellation Register, (xvi)

Axle counter reset register, etc. (xvii) Supply

and preparation of SIP where required. Note:-

(i) All the diagram will be made on Auto CAD.

The paper size of wiring diagram will be A-3

or as per IRSEM or as per IRSEM. Soft Copy/

AUTOCAD file of all drawings to be submitted

alongwith paper drawing. Wiring diagram will

be made in 'Black colour'. Alteration to wiring

diagram will be done using 'RED' and 'Green'

colouring scheme. RED = new

equipment/contact to be installed or

commissioned. GREEN = redundant

equipment/ contact to be recovered. (a) Up to

CKP-DIVN- S AND T/SOUTH EASTERN RLY

17 17 Design and supply of the following drawings Station 1.00 77475.00 77475.00

to office records as per requirement of the

Railways. This includes alteration at different

stages and finally supply of all the drawings

including tracings within 30 days or as

defined in the tender document from the date

of commissioning of the work, otherwise

penalty to be imposed as per tender

document. This includes the following

drawings for each station: (1) Cable layout

plan, (2) Cable corrage plan, (3) Location Hut

drawing, (4) Termination chart of end

goomties and location hut, (5) Traction

bonding plan, (6) Contact Analysis Chart, (7)

SWRD & GWRD, (8) Equipment Layout Plan,

(9) Power Supply arrangement diagram, (10)

Relay Disposition chart, (11) Any other

drawing as found relevant as per site

condition. Office record if online maintenance

is not implemented includes the following: (i)

Battery History book, (ii) Track Circuiting

Register, (iii) Track circuit maintenance

Register, (iv) Cable Meggering Register, (v)

Signal History Register, (vi) LED Register, (vii)

Glued joint/ Block joint Register, (viii) Point

machine Maintenance Register, (ix) Joint

Inspection Register such as P. Way, Electrical

& Signal, (x) Relay Register, (xi) Route

cancellation Register, (xii) Relay Room Key

Register, (xiii) Emergency Point operation

Register, (xiv) Crank Handle Register, (xv)

Emergency Route Cancellation Register, (xvi)

Axle counter reset register, etc. (xvii) Supply

and preparation of SIP where required. Note:-

(i) All the diagram will be made on Auto CAD.

The paper size of wiring diagram will be A-3

or as per IRSEM or as per IRSEM. Soft Copy/

AUTOCAD file of all drawings to be submitted

alongwith paper drawing. Wiring diagram will

be made in 'Black colour'. Alteration to wiring

diagram will be done using 'RED' and 'Green'

colouring scheme. RED = new

equipment/contact to be installed or

commissioned. GREEN = redundant

equipment/ contact to be recovered. (a) For

more than 10 line yard.

18 18 Preparation of Station Working Rules (SWR) in Set 2.00 13595.00 27190.00

English on the basis of station working rule

diagram and gate working rule diagram to be

supplied by the contractor. Submission of two

draft copy to railway for checking and

resubmission of draft in three copies for

approval of division after making corrections.

Editable Soft copy to be supplied in pen drive.

19 19 Preparation of Station Working Rules (SWR) in Set 2.00 13595.00 27190.00

Hindi/Regional Language of that station on

the basis of station working rule diagram and

gate working rule diagram to be supplied by

the contractor. Submission of two draft copy

to railway for checking and resubmission of

draft in three copies for approval of division

after making corrections. Editable Soft copy to

be supplied in pen drive.

CKP-DIVN- S AND T/SOUTH EASTERN RLY

20 20 Designing and Plotting of Signalling Per SIP 2.00 28072.00 56144.00

Interlocking Plan(SIP) in AUTOCAD. Two

copies of prints with soft copy will be

submitted to Railway for checking. If

alterations are suggested/proposed by

Railways then again two copies of prints will

be submitted for advance approval after

carrying out all the alterations as

suggested/proposed by the Railways.

Tracings will be submitted for all the diagrams

mentioned above for the purpose of approval

by Railway prior to commissioning of station.

21 21 Mechanised Drilling/Micro Tunnelling under Metre 30.00 2215.00 66450.00

important/ busy metal/concrete road/Railway

track and laying of GI pipe including supply

(make: TATA/ Jindal or better) of min. 75mm

inner diameter Grade Medium with Spec. No.

IS- 1239, Pt-1, 2004 including supply, Boring

and pulling cable upto 110mm dia. at a depth

of min. 1 meter as per site condition. This also

includes reinstatement of the surface to the

original state.

22 22 Alteration/modification in existing location Numbers 3.00 2734.00 8202.00

boxes, includes fixing/Removal or both the

equipment, cable insertion, termination,

wiring, testing & commissioning, two coat

painting, lettering to suit the circuits as per

approved wiring diagram. This includes filling

with sand and plastering the same. Note: All

the sundry materials such as paint, sand,

cement, screws etc to be supplied by the

Cables/tail cables) at location boxes, cable Conductor

termination rack in relay room, station

building, etc. The item includes dressing of

cables and wires with dressing threads as per

standard practice. All material required for

this item will be supplied by contractor.

24 24 Physical tracing and opening/locating of Metre 80.00 257.00 20560.00

existing working cables by precision digging

for diversion of cables in connection with

cable clearance for engineering earth work or

for utility shifting without interfering the

circuits as per the advice of Railway site

Engineer-in-charge.

25 25 Removal of normally 13m Rail in the way of Numbers 10.00 117.00 1170.00

cable route trench, signal/location box

foundation, track crossing etc. In case of less

or more than 13 m, proportionate payment to

be done. These obstructions will be removed

by the contractor for ensuring proper

execution of related works.

26 26 Removal of PSC/Wooden/Steel sleeper in the Numbers 10.00 118.00 1180.00

way of cable route trench, signal/location box

foundation, track crossing etc. These

obstructions will be removed by the

contractor for ensuring proper execution of

related works. Note: In case of broken

sleepers, proportionate payment will be

27 27 Supply, transportation and fixing of RCC Cable Numbers 8.00 576.00 4608.00

Route Marker as per SEM drawing No. 15-D1

or latest. (Inspection by representative of Sr.

CKP-DIVN- S AND T/SOUTH EASTERN RLY

28 28 Modification/Upgradation, wiring, validation & Set 2.00 46855.00 93710.00

alteration of Data Logger/RTU of Digital &

Analog Input including NMDL software etc. as

per site engineer. The necessary wire from

relay to tag block & from tag block to data

logger, tag block, terminal, wiring material

etc. required for this work to be supplied by

contractor. Wire to be procured from RDSO

approved firms.

29 29 Cleaning of Debris and Bushes surrounding Sqm 20.00 11.00 220.00

the Goomty/Apparatus Case/Store

Complex/under the existing running rod or

any other Signalling installation as instructed

by Engineer-in-charge.

30 30 Removal of Earth of all kinds of soils/rocks, cum 12.00 142.00 1704.00

boulders including mud/slush, slipped earth in

catch water drains, side drains, over berms in

cutting, water way of bridges, over coping of

toe/breast/retaining walls etc. including

crossing of nallah, railway tracks,

making/repairing approach roads if required,

all lead, lift, handling, re-handling, ascent,

descents, or any other obstruction including

all labour and material as a complete job.

Earth spoils to be dumped outside the cutting

or railway embankments as per direction of

Engineer-in-charge.

commissioning of track circuit on Straight

Portion of Track (without involving points and

crossings) as per Drawing No. SK/DRG/OL/27

or latest and track bonding plan. The work

includes drilling of 9/32" hole on Rails,

provision of bonding, fixing and painting of

Track Lead Junction Boxes, termination of tail

cables, termination of Track lead wires,

double Jumper wires, Installation & wiring of

track feed set (Track Charger, Adjustable

Resistance, choke coil, fuses, battery, relays

etc.), testing of Glued/Block Joints and also

lettering/numbering of track lead junction

boxes, block joints and track circuits. This also

includes transportation of all materials

required for the above installation. Note:

Track feed set, bonding wires, TLJB, channel

pin, tail cable to be supplied by Railway.

Schedule B-Material Supply(SOR) for (Dual Detection by Commissioning of T/Cct in Jt/line between

Item- 1 Details of Schedule 'B' are given below: -

S No. Item Description of Item Unit Qty Rate Amount

1 01 Supply of Sulphuric Acid solution having Kg 20.00 46.00 920.00

nominal specific Gravity 1210. (Inspection by

representative of Sr. DSTE/CKP)

for Track Circuit Bonding or for other

application as per Specification No.IS:279/81

or latest. (Inspection by representative of Sr.

3 03 Supply of Insulated galvanized flexible Kg 70.00 207.00 14490.00

stranded wire rope 7x7 construction, 19 mm

circumference, Tensile Strength 125-140 Kg

per square mm as per Specification No. IRS:S-

3/61 or latest wrapped with Extruded jacket of

PVC, thickness 2 mm. Wire colour will be

decided by Engineer-in-charge. (Inspection by

representative of Sr. DSTE/CKP)

CKP-DIVN- S AND T/SOUTH EASTERN RLY

4 04 Supply of 30 mm length Channel Pins, single Numbers 120.00 2.00 240.00

groove for bonding Track Circuiting wires of

7mm dia. for 4mm dia. bond wire to RDSO

Drawing No. S-69/M or latest as per

Specification No. IRS: S17-75 Rev 3 & IS:

1573-70 or latest. (Inspection by

representative of Sr. DSTE/CKP)

5 05 Supply of Steel Apparatus case Full height as Numbers 8.00 17430.00 139440.00

per Drawing No. SK/Drg./OL/SER /198 or latest

with E type lock . E-type lock & their key ward

No. will be decided by site engineer as per

Specification No. IRS: S-10/78 with Rev. 8 or

latest. Supply of Hylam sheets is not covered

under this scope. This includes supply of one

key & handle for each four Apparatus Case or

minimum one. (Inspection by representative

of Sr. DSTE/CKP)

6 06 Supply of Earth Electrode as per Drawing No. Set 8.00 2712.00 21696.00

19-D6 of SEM-2021 or latest. GI pipe

confirming to IS:1239 or latest of 3.17 mm

thickness, minimum 2.5 m long, 50.8 mm

diameter, 4.76 mm diameter drilled holes

staggered at distance of 152.4 mm.

(Inspection by representative of Sr.

7 07 Supply of 25 mm 6 Way PBT ARA Terminal Numbers 90.00 322.00 28980.00

block as per Specification No. IRS:S-75/2006

Rev. 2.0 or latest as per IRS Drg. No. SA-

23756 Alt-3 or its latest amendments.

(Inspection by representative of Sr.

8 08 Supply of Non-Deteriorating type of low Numbers 20.00 55.00 1100.00

voltage electric fuse for Railway signalling

use, fuse with cylindrical cap without

indication, cylindrical fuse as per Specification

No. IRS:S-78/2006 or latest. (a) ND Fuse

Cylindrical Type 4/6 Amp. (Inspection by

9 09 Supply of PBT fuse block as per Specification Numbers 20.00 109.00 2180.00

No. IRS:S-75/2006 Rev. 2.0 or latest as per

IRS drawing No. SA: 23748 with alt 4 or its

latest amendments. (Inspection by RDSO)

10 10 Supply of PVC Insulated Single core Kilometre 1.50 7832.00 11748.00

Multistrand, unsheathed with plain

annealed/tinned copper conductor 16/0.2 mm

diameter as per Specification No. IRS:S-76/89

or latest. Wire Colours shall be decided by

engineer-in-Charge. Note: The requirement of

plain/tinned copper to be decided by the

Engineer-in- charge. (Inspection by

representative of Sr. DSTE/CKP)

11 11 Supply of PVC Insulated single core cable Kilometre 0.30 21278.00 6383.40

multistrand, unsheathed with plain

annealed/tinned copper conductor 3/0.75 mm

diameter as per Specification No. IRS:S-76/89

or latest. Wire Colours shall be decided by

engineer-in-Charge. Note: The requirement of

plain/tinned copper to be decided by the

Engineer-in-charge. (Inspection by

representative of Sr. DSTE/CKP)

12 12 Supply of PVC Insulated single core cable Kilometre 0.30 43745.00 13123.50

multistrand, unsheathed with plain

annealed/tinned copper conductor 7/0.75 mm

diameter as per Specification No. IRS:S-76/89

or latest. Wire Colours shall be decided by

engineer-in-Charge. Note: The requirement of

plain/tinned copper to be decided by the

Engineer-in-charge. (Inspection by

representative of Sr. DSTE/CKP)

CKP-DIVN- S AND T/SOUTH EASTERN RLY

13 13 Supply of 35 mm x 6 mm thick MS Flat Plate Metre 40.00 166.00 6640.00

Strip as per IS: 226-1975 or latest for earth

connection to Signal post, L/Box etc.

(Inspection by representative of Sr.

14 14 Supply of pressure Sensitive Adhesive Numbers 6.00 32.00 192.00

Plasticized PVC Tapes having 20 mm width,

minimum 25 Meter length. The colour of the

tape shall be decided by Railway in-charge.

Make: Protex/Nippon/Anchor or better.

(Inspection by representative of Sr.

15 15 Supply of PVC Insulated Multicore copper Kilometre 0.10 94546.00 9454.60

conductor Indoor Cable 40 Core x 0.6mm

diameter as per Specification No. IRS:S-76/89

or latest. (Inspection by representative of Sr.

16 16 Supply of 1 copy of SWR in English finally Numbers 6.00 522.00 3132.00

approved by railways along with spiral

binding. This has to be done after CRS

sanction has been obtained. (Inspection by

representative of Sr. DSTE/CKP)

17 17 Supply of 1 copy of SWR in Hindi/Regional Numbers 6.00 522.00 3132.00

Language of that station finally approved by

railways along with spiral binding. This has to

be done after CRS sanction has been

obtained. (Inspection by representative of Sr.

Schedule C-Execution(SOR) for (Auto Media Change over system for SSDACs & UFSBI over CKP

Item- 1 Details of Schedule 'C' are given below: -

S No. Item Description of Item Unit Qty Rate Amount

1 01 Transportation and fixing of PVC Conduit Metre 500.00 15.00 7500.00

pipe/channel/casing caping on wall or

structure with drawls of Telecom/Power/Data

cable with proper finishing. This includes

supply of fixing materials including flexible

pipe/bend etc. as required during course of

2 02 Installation, splicing and commissioning of Numbers 20.00 4016.00 80320.00

Fibre Distribution Management system

(FDMS) for 24 Fiber complete with all

accessories such as patch cord & pigtail etc.

as per TEC Spec. with latest amendment. The

sundry material if required any to be supplied

Schedule D-Material Supply(SOR) for (Auto Media Change over system for SSDACs & UFSBI over

Item- 1 Details of Schedule 'D' are given below: -

S No. Item Description of Item Unit Qty Rate Amount

1 01 Supply of UTP CAT - 6 cable, having bare Metre 500.00 17.00 8500.00

Copper Conductor of diameter 0.5 mm,

Suitable for Gigabit Ethernet TEC

Specification No. G/WIR 06/02 or latest.

(Inspection by representative of Sr.DSTE/CKP)

2 02 Supply of RJ-45 connector. Make: D-link or Numbers 1632.00 6.00 9792.00

better. (Inspection by representative of

Schedule D1-Material Supply(Non-SOR) for (Auto Media Change over system for SSDACs & UFSBI

over CKP Division)

Item- 1 Details of Schedule 'D1' are given below: -

CKP-DIVN- S AND T/SOUTH EASTERN RLY

S No. Item Description of Item Unit Qty Rate Amount

commissioning of Automatic Change Over

device of DAC/UFSBI V.21/ V.23 to optical

fibre, STM(E1), standard 19" rack mountable

device consisting of two E1 port supporting

120 Ohms interface, dual optical ports with

(1+1) hot stand by (dual core path and single

core path) 20 kms driving distance and four

V.21/V.23 (E&M) 24W/4W interfaces with auto

change over mechanism to Quad ports

2W/4W, each port configurable as 2W or 4W

no restriction in configuration , unit to support

potential free contacts four number an cbe

linked with data logger/RTU for E1 status,

Quad status and Power supply status, unit

support front panel resettable audio able

buzzer in case of main link fails (Optical or

E1), unit to support power OFF fail safe

mechanism when the unit is switched OFF the

inputs is bypassed to the quad cable

automatically unit support, unit for quad

health status, E1 dual optical dual path, Dual

DC power supply 18VDC to 72V DC range

make: Team link/Team Engg/Cygnus

/FABIO1CX-4P or superior. (Technical

Specification as per Annexure-A attached)

(Inspection by RITES)

2 02 Supply of 6A DP C series MCB. (Inspection by Numbers 202.00 609.91 123201.82

representative of Sr.DSTE/CKP)