PROVN OF COVERED BATHING POINT NEAR BLDG NO T-21 (OR LIVING LINE) (JOB NO 41SA/MINOR/03/2024-25), PROVN OF 05 X GEYSERS OF 25 LTR CAPACITY FOR SINGLE JCOs ACCN (BLDG NO P-33 nd P-34) nd MI ROOM (JOB NO 41SA/MINOR/06/2024-25)

Amount

NOTES :The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates.

Excavating in post holes in soft / loose soil (or similar holes) each n exc 0.5 cu m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and as directed.

Material and labour for plain cement concrete M-10(Nominal Mix) using 20 mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and as directed.

Excavating over areas, n exc 1.5 m deep and getting out as in soft/loose soil etc complete all as specified and as directed.

Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level n. exc. 1.50 m above the starting point.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm as in soft/loose soil.

Material and labour for Hardcore of gauge not exceeding 63 mm of broken stone or boulders , spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface etc complete all as specified and as directed.

Material and labour for Plain Cement Concrete M-15(Nominal Mix) using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for Reinforced Cement Concrete M-25 ( Design Mix ) using 20 mm graded stone aggrgate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete etc complete all as specified and as directed.

Material and labour for Use and waste of formwork for foundations, foundation beams , bases for columns, etc. for rough finished surfaces of concrete complete all as specified and as directed.

S&F rolled mild steel works in compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc.including painted one shop coat of zinc chromate primer paint (including preparation of surface) complete all as specified and as directed.

Material and labour for Plain Cement Concrete M-15(Nominal Mix) using 12.5 mm graded stone aggregate as in fcoping including necessary form work etc complete all as specified and directed.

Material and labour for Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping round for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips confirming to Fe-410-W (Gde.E-250) Part- I quality-A or Fe 290 (Gde -E-65) complete all as specified and as directed.

Material and labour for MS Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc and similar work conforming to Fe-290 Gde E-165 →complete all as specified and as directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with ashers and one hexagonal or square nut, n exc 5cm long dia of neck 5 to 10 mm long etc complete all as specified and as directed.

S&F of aperature size 75 x 75 mm and dia 3.15mm chain ink MS galvanized fencing, any size or type etc all as specified and as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire all as specified and as directed.

S&F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) all as specified and as directed.

Material and labour for preparation of new steel surface and applying two coats of black bituminous paint over on new steel and iron surfaces of any description over exceeding 10 cm in width or girth complete all as specified and as directed.

S&F CONSECZAL super razor punched barb tape (SRPBT) Aluminium base helix coil with and including necessary GI fixing clip for securing complete all as specified and as directed and as directed following specifications (I) dia of coil in stretched 600mm (ii) no of circle - 42 turns per coil (iii) weight of each coil with hessian pack - 12.50kg (iv) coverage per coil - 8rm (v) central core wire made from 2.5mm dia - HTSS wire as per IS - 4454 galvanised as per IS 2629 (vi) RAZAR PUNCHED STRIP RAZOR PUNCHED TAPE consec zal steel comprising of aluminium case with zinc alloy 2150 GM/M2 CONFORMING TO astm a-792/M with additional primer treatment of epoxy polyurethane final paint top coat of caulified green shade bsl 139 by hot dipping process (Running length of wall shall be measured for payment purpose)

Material and labour for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel and iron surfaces of any description over exceeding 10 cm in width or girth complete all as specified and as directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft / loose soil etc complete all as specified and as directed.

Material and labour for 100 mm thick Plain Cement Concrete M-15(Nominal Mix) using 40 mm graded stone aggregate laid in alternate panel , finished fair and even without using extra cement and spike rolling to concrete surfaces or making impressions of expanded metal whilst the concrete is green etc omplete all as specified and directed.

M&L for Brickwork with subclass ‘B’ bricks, old size ,straight or curved on plan exc 6m mean radius built in cement sand mortar 1:6 etc complete all as specified and as directed.

M&L for Rendering 15 mm in Cement Mortar 1:6 on other than fair faces of brick work or concrete surfaces finished even smooth without using extra cement to the plastered surface complete all as specified and as directed.

Material and labour for preparation of new or previously untreated surfaces of wall and applying three coats of white wash etc complete all as specified and as directed..

Material and labour for 75 mm thick plain cement concrete M-10(Nominal Mix) using 20 mm graded stone aggregate as in plinth protection, finished even and smooth without using extra cement complete all as specified and as directed.

S&F rolled mild steel works as in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410- W(Gde-E-250) quality-B etc complete all as specified and as directed.

Material and labour for mild hollow steel sections steel of grade YSt 310 conform to IS 4923 in roof trusses (framed), trussed, purlins, bracing and fastenings including distance pieces, cleats etc including one shop coat of zinc chromate primer after preparation of surface complete all as specified and as directed.

Supply and fixing of pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick and an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Supply and fixing of pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridges, tips, valley, gutters, length & girth as fixed with nail or screws complete all as specified and as directed.

Supply and fixing of bib tap cast copper alloy fancy type CP with crutch or butterfly handle ,screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified.

Supply and fixing of 15mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors complete all as specified and as directed.

Supply and fixing of 20mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors complete all as specified and as directed.

Supplying, hoisted and fixed in position rotational moulded polyethylene water storage tanks in double layers and cylindrical vertical type with manhole lids(closed top) of 1000 litres capacity with ISI marked and all as specified in IS 12701 complete all as specified and directed .

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation etc. or for shafts, wells, cess pits, manholes, pier holes etc. not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out as in soft/loose soil.

Material and labour for Plain Cement Concrete M-7.5(Nominal Mix) using 40 mm graded stone aggregate as in foundation filling and mass concrete in sub base complete all as specified and directed.

Material and labour for 100 mm thick Plain Cement Concrete M-15(Nominal Mix) using 40 mm graded stone aggregate laid in alternate panel , finished fair and even without using extra cement etc omplete all as specified and directed.

Material and labour for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; etc omplete all as specified and directed.

Supply and fixing of uPVC of type-B for use in soil and waste discharge systems, single socket, 110 mm bore in any length including rubber ring joints and fixed to walls with MS clips 25 mm x 3 mm with suitable nuts and bolts all as specified in IS 13592 complete all as specified and directed.

Supply and fixing of Unplasticized (uPVC )bend for 110 mm bore uPVC pipe complete all as specified and directed.

M&L for Rendering 15 mm in Cement Mortar 1:4 on other than fair faces of brick work or concrete surfaces finished even smooth without using extra cement to the plastered surface complete all as specified and as directed.

Material and labour for 100 mm thick Plain Cement Concrete M-15(Nominal Mix) using 20 mm graded stone aggregate laid in alternate panel , finished fair and even without using extra cement etc omplete all as specified and directed.

M&L for forming 12 mm thick expansion joints 100 mm thick concrete floor , filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ etc complete all as specified and as directed.

Material and labour for Precast Reinforced Cement Concete cover slab type M-20 (Nominal mix) using 20 mm graded stone aggregate, set in Cement Mortar (1:4) complete all as specified and directed.

Material and labour for TMT Bars Fe 500D 10mm dia & over cut to length bent to shape required inculding cranking bending spirally hooping for columns etc and binding with MS wire ennealed less than 0.9mm dia or securing with clip complete all as specified and directed.

Material and labour fo TMT bars Fe 500D of 6 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally and binding with and including mild steel (annealed) wire not less than 0.90 mm dia etc complete all as specified and as directed.

Material and labour for machine pressed and chemically treated , smooth finished exterior graded coloured pre-polished chequered Cement Concrete tiles of 25 mm minimum thick, size of (square/ rectangular) area of each tile exceeding 0.09 Sqm but not exceeding 0.16 Sqm double layer machine pressed set ( as per IS 1237, jointed and pointed in neat cement slurry in floors and cut & polished in white or coloured cement to match over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed.

Subtotal of Sch A part-I

SCHEDULE 'A' PART - II FOR E/M PORTION (Sl No __ to ____)

Material and labour for point wiring with 4.0 Sq. mm (nominal area) PVC insulated and sheathed single core FRLSH copper cable 1100 volts grade with stranded copper conductor in and including PVC rigid concealed conduit (heavy grade) and conduit accessories alongwith continuous earth wire 4.0 Sq mm PVC insulated and sheathed single core FRLSH cable 1100 volts grade with stranded copper conductor and connected to common earth dolly complete for one modular socket outlet 5 Pin , 15/16 amps on independant board etc complete all as specified and as directed.

Supply and fix water heater( Geyser) , storage type , electrically operated , steel body with copper inner tank and heating element 2 KV , capacity 25 litre , BEE 5 star rated , complete with all accessories such as safety valve , thermostat, NRV common piece including suitable fixing arrangement etc complete all as specified and as directed.

Material and labour for sub main wiring with single core PVC insulated , 1100V grade FRLSH copper cable 6 sqmm stranded conductor and drawn through and including PVC rigid non metallic surface casing capping medium duty ( ISI marked) with all accessories such as junction boxes, bends, tees, including continous earth wire , connected to common dolly etc complete all as specified and as directed. Note:- 1.One run of PVC casing capping, 02 x runs of 6 sqmm FRLSH copper cable ( Phase plus neutral ) and 01 x run of 6 sqmm FRLSH copper cable as earth wire shall be measured as one unit and shall be considered for payment. 2. Colour code of cable (s) shall be ensured as per standard engineering practice / norms.

Supply and fix SPN enclosure with a two pin and earth plug and socket complete with DP 20 Amps MCB etc complete all as specified and as directed.

Material and labour for point wiring with 1.5 Sq. mm (nominal area) PVC insulated and sheathed single core FRLSHcopper cable 1100 volts grade with stranded copper conductor in and including PVC rigid concealed conduit (heavy grade) and conduit accessories alongwith continuous earth wire 1.5 Sq mm PVC insulated and sheathed single core FRLSH cable 1100 volts grade with stranded copper conductor and connected to common earth dolly complete for one light/fan point controlled by one way modular switch complete all as specified and as directed.

Supply and fixing ceiling rose surface bakelite 65x50mm three terminals ISI marked complete all as specified and as directed.

Material and labour for Modular switch 6 Amp single pole one way flush type ISI marked complete all as specified and as directed.

Material and labour for Modular fan regulator 6 Amp single pole electronic type ISI marked complete all as specified and as directed.

Supply and Fixing or hanging ceiling fan 230V, 1200 mm sweep,complete with three blades down rods min air delivery 210 CMM with service value 6.00 , BEE 5 star rated with brushless direct current motor ( BLDC) , writing the MES fan numbers with paint and 0.75 Sqmm , 3 core PVC insulated Flexible copper cable for connection from ceiling rose to fan complete all as specified and as directed.

Supply and Fixing wall mounted fan 230V, 450 mm sweep,complete with three blades min air delivery 100 CMM , BEE 5 star rated writing the MES fan numbers with paint including connection ISI marked etc complete all as specified and as directed.

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ₹ ___________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ.

M/S Deep Construction

M/S BARUAH ELECTRICALS

M/S AK SINGH