Providing Interior Furnishing, Electrical, Air Conditioning, EPVAX system and other allied works to 6th floor Multi Office Complex at Moti Daman. (E-30018)

Amount

Civil work

Furniture Work Providing and fixing 3/4th full height partition 2"x2" aluminium frame with 1.5mm thick (15 guage) swastik jindal make section placed 2' c/c verticaly as well as horizontaly joint less vertical members bottom of the frame work to be seemed to the floor& slab with concealed hardware & screws, adhesive wherever necessry, frame to be sandwiched in bed with 8mm commercial ply & finished with 1mm thick Laminate on both sides.All visible edges to be finish in teak wood patti with french polish complete including skirting cutout of switch plate,switch box light fittings etc.and making provision to lay electrical conduits and data voice wiring complete with all respects. 8mm Commercial Plywood Green/Sainik/Ecotec make.(Basic Cost - Rs 732 /- per sq.mt and Weight of the Plywood Sheet i.e 2400mm x 1200mm to be around 24kg ).Laminate - GreenLam or Century Make - 107SF or 108SF.(Basic Cost- 1200 per Sheet(2400mm x 1200mm).All Visible edges to be finished in 4mm teak veneer.(Basic Cost -Rs 80/- Per Sq.ft).All Hardware Enox Make in SS finish.

Glass door of Size 1800mm X 2700mm with door frames of 45 x 32mm in extruded tubular aluminimum,duly powder coated/annodized and 12mm thick clear toughened glass door with all necessary hardware and fiitings as complete.

Supplying and Eco wooden storage unit body is made from 18mm PLB with all the edges sealed with 0.8 mm thick PVC Edgeband. The Back panel is 9mm White PLT. The entire construction is ready to assemble unit and is assembled with suitable KD fittings. The shelves and separator panels ( if available ) is made from 18 mm white PLT and edges are sealed with 0.8 mm edge band. The bottom shelf is fixed and other shelves have one step adjustment for optimizing the space. Doors : Door Panels ae made from 18 mm PLB with 2 mm Edge band on all edges ad a flush Plastic handle is fitted vertically at the center of the door. The hinge door has suitable hinges and HDU is fitted with an adjustable fitting for height adjustment. The SDU runs in a PVC track mounted on the TOP and Bottom panel of the Body. HDU has a three point lock and SDU has a push type lock. All the storages are fitted with a 6 mm leveler at bottom for leveling. Size of (A) 1200W x 450D x 2400H.

Supplying and Eco wooden storage unit body is made from 18mm PLB with all the edges sealed with 0.8 mm thick PVC Edgeband. The Back panel is 9mm White PLT. The entire construction is ready to assemble unit and is assembled with suitable KD fittings. The shelves and separator panels ( if available ) is made from 18 mm white PLT and edges are sealed with 0.8 mm edge band. The bottom shelf is fixed and other shelves have one step adjustment for optimizing the space. Doors : Door Panels ae made from 18 mm PLB with 2 mm Edge band on all edges ad a flush Plastic handle is fitted vertically at the center of the door. The hinge door has suitable hinges and HDU is fitted with an adjustable fitting for height adjustment. The SDU runs in a PVC track mounted on the TOP and Bottom panel of the Body. HDU has a three point lock and SDU has a push type lock. All the storages are fitted with a 6 mm leveler at bottom for leveling. Size of (B) 1650W X 450D X 2400H.

Supplying and Eco wooden storage unit body is made from 18mm PLB with all the edges sealed with 0.8 mm thick PVC Edgeband. The Back panel is 9mm White PLT. The entire construction is ready to assemble unit and is assembled with suitable KD fittings. The shelves and separator panels ( if available ) is made from 18 mm white PLT and edges are sealed with 0.8 mm edge band. The bottom shelf is fixed and other shelves have one step adjustment for optimizing the space. Doors : Door Panels ae made from 18 mm PLB with 2 mm Edge band on all edges ad a flush Plastic handle is fitted vertically at the center of the door. The hinge door has suitable hinges and HDU is fitted with an adjustable fitting for height adjustment. The SDU runs in a PVC track mounted on the TOP and Bottom panel of the Body. HDU has a three point lock and SDU has a push type lock. All the storages are fitted with a 6 mm leveler at bottom for leveling. Size of (C) 1800W X 450D X 2400H.

Supplying and Eco wooden storage unit body is made from 18mm PLB with all the edges sealed with 0.8 mm thick PVC Edgeband. The Back panel is 9mm White PLT. The entire construction is ready to assemble unit and is assembled with suitable KD fittings. The shelves and separator panels ( if available ) is made from 18 mm white PLT and edges are sealed with 0.8 mm edge band. The bottom shelf is fixed and other shelves have one step adjustment for optimizing the space. Doors : Door Panels ae made from 18 mm PLB with 2 mm Edge band on all edges ad a flush Plastic handle is fitted vertically at the center of the door. The hinge door has suitable hinges and HDU is fitted with an adjustable fitting for height adjustment. The SDU runs in a PVC track mounted on the TOP and Bottom panel of the Body. HDU has a three point lock and SDU has a push type lock. All the storages are fitted with a 6 mm leveler at bottom for leveling. Size of (A) 1500W x 450D x 1200H.

Supplying and Eco wooden storage unit body is made from 18mm PLB with all the edges sealed with 0.8 mm thick PVC Edgeband. The Back panel is 9mm White PLT. The entire construction is ready to assemble unit and is assembled with suitable KD fittings. The shelves and separator panels ( if available ) is made from 18 mm white PLT and edges are sealed with 0.8 mm edge band. The bottom shelf is fixed and other shelves have one step adjustment for optimizing the space. Doors : Door Panels ae made from 18 mm PLB with 2 mm Edge band on all edges ad a flush Plastic handle is fitted vertically at the center of the door. The hinge door has suitable hinges and HDU is fitted with an adjustable fitting for height adjustment. The SDU runs in a PVC track mounted on the TOP and Bottom panel of the Body. HDU has a three point lock and SDU has a push type lock. All the storages are fitted with a 6 mm leveler at bottom for leveling. Size of (B) 2100W X 450D X 750H.

Supplying and Eco wooden storage unit body is made from 18mm PLB with all the edges sealed with 0.8 mm thick PVC Edgeband. The Back panel is 9mm White PLT. The entire construction is ready to assemble unit and is assembled with suitable KD fittings. The shelves and separator panels ( if available ) is made from 18 mm white PLT and edges are sealed with 0.8 mm edge band. The bottom shelf is fixed and other shelves have one step adjustment for optimizing the space. Doors : Door Panels ae made from 18 mm PLB with 2 mm Edge band on all edges ad a flush Plastic handle is fitted vertically at the center of the door. The hinge door has suitable hinges and HDU is fitted with an adjustable fitting for height adjustment. The SDU runs in a PVC track mounted on the TOP and Bottom panel of the Body. HDU has a three point lock and SDU has a push type lock. All the storages are fitted with a 6 mm leveler at bottom for leveling. Size of (C) 1650W X 450D X 750H.

Supplying and Eco wooden storage unit body is made from 18mm PLB with all the edges sealed with 0.8 mm thick PVC Edgeband. The Back panel is 9mm White PLT. The entire construction is ready to assemble unit and is assembled with suitable KD fittings. The shelves and separator panels ( if available ) is made from 18 mm white PLT and edges are sealed with 0.8 mm edge band. The bottom shelf is fixed and other shelves have one step adjustment for optimizing the space. Doors : Door Panels ae made from 18 mm PLB with 2 mm Edge band on all edges ad a flush Plastic handle is fitted vertically at the center of the door. The hinge door has suitable hinges and HDU is fitted with an adjustable fitting for height adjustment. The SDU runs in a PVC track mounted on the TOP and Bottom panel of the Body. HDU has a three point lock and SDU has a push type lock. All the storages are fitted with a 6 mm leveler at bottom for leveling. Size of (A) 4650W x 450D x 750H.

Supplying and Eco wooden storage unit body is made from 18mm PLB with all the edges sealed with 0.8 mm thick PVC Edgeband. The Back panel is 9mm White PLT. The entire construction is ready to assemble unit and is assembled with suitable KD fittings. The shelves and separator panels ( if available ) is made from 18 mm white PLT and edges are sealed with 0.8 mm edge band. The bottom shelf is fixed and other shelves have one step adjustment for optimizing the space. Doors : Door Panels ae made from 18 mm PLB with 2 mm Edge band on all edges ad a flush Plastic handle is fitted vertically at the center of the door. The hinge door has suitable hinges and HDU is fitted with an adjustable fitting for height adjustment. The SDU runs in a PVC track mounted on the TOP and Bottom panel of the Body. HDU has a three point lock and SDU has a push type lock. All the storages are fitted with a 6 mm leveler at bottom for leveling. Size of (B) 4800W X 450D X 750H.

Supplying and Eco wooden storage unit body is made from 18mm PLB with all the edges sealed with 0.8 mm thick PVC Edgeband. The Back panel is 9mm White PLT. The entire construction is ready to assemble unit and is assembled with suitable KD fittings. The shelves and separator panels ( if available ) is made from 18 mm white PLT and edges are sealed with 0.8 mm edge band. The bottom shelf is fixed and other shelves have one step adjustment for optimizing the space. Doors : Door Panels ae made from 18 mm PLB with 2 mm Edge band on all edges ad a flush Plastic handle is fitted vertically at the center of the door. The hinge door has suitable hinges and HDU is fitted with an adjustable fitting for height adjustment. The SDU runs in a PVC track mounted on the TOP and Bottom panel of the Body. HDU has a three point lock and SDU has a push type lock. All the storages are fitted with a 6 mm leveler at bottom for leveling. Size of (C) 3300W X 450D X 750H.

Supplying and Eco wooden storage unit body is made from 18mm PLB with all the edges sealed with 0.8 mm thick PVC Edgeband. The Back panel is 9mm White PLT. The entire construction is ready to assemble unit and is assembled with suitable KD fittings. The shelves and separator panels ( if available ) is made from 18 mm white PLT and edges are sealed with 0.8 mm edge band. The bottom shelf is fixed and other shelves have one step adjustment for optimizing the space. Doors : Door Panels ae made from 18 mm PLB with 2 mm Edge band on all edges ad a flush Plastic handle is fitted vertically at the center of the door. The hinge door has suitable hinges and HDU is fitted with an adjustable fitting for height adjustment. The SDU runs in a PVC track mounted on the TOP and Bottom panel of the Body. HDU has a three point lock and SDU has a push type lock. All the storages are fitted with a 6 mm leveler at bottom for leveling. Size of (A) 2700W x 450D x 750H.

Supplying and Eco wooden storage unit body is made from 18mm PLB with all the edges sealed with 0.8 mm thick PVC Edgeband. The Back panel is 9mm White PLT. The entire construction is ready to assemble unit and is assembled with suitable KD fittings. The shelves and separator panels ( if available ) is made from 18 mm white PLT and edges are sealed with 0.8 mm edge band. The bottom shelf is fixed and other shelves have one step adjustment for optimizing the space. Doors : Door Panels ae made from 18 mm PLB with 2 mm Edge band on all edges ad a flush Plastic handle is fitted vertically at the center of the door. The hinge door has suitable hinges and HDU is fitted with an adjustable fitting for height adjustment. The SDU runs in a PVC track mounted on the TOP and Bottom panel of the Body. HDU has a three point lock and SDU has a push type lock. All the storages are fitted with a 6 mm leveler at bottom for leveling. Size of (B) 1500W X 450D X 750H.

Supplying and Eco wooden storage unit body is made from 18mm PLB with all the edges sealed with 0.8 mm thick PVC Edgeband. The Back panel is 9mm White PLT. The entire construction is ready to assemble unit and is assembled with suitable KD fittings. The shelves and separator panels ( if available ) is made from 18 mm white PLT and edges are sealed with 0.8 mm edge band. The bottom shelf is fixed and other shelves have one step adjustment for optimizing the space. Doors : Door Panels ae made from 18 mm PLB with 2 mm Edge band on all edges ad a flush Plastic handle is fitted vertically at the center of the door. The hinge door has suitable hinges and HDU is fitted with an adjustable fitting for height adjustment. The SDU runs in a PVC track mounted on the TOP and Bottom panel of the Body. HDU has a three point lock and SDU has a push type lock. All the storages are fitted with a 6 mm leveler at bottom for leveling. Size of (C) 4350W X 450D X 750H.

Providing and fixing of vertical zebra roller blinds 100% dark with ball chain etc. (Basic Rate of Rs. 1500.00/M2) Complete with all required hardware and fitting approved make and colour complete with all respects as directed by architect.

Providing and supplying Centre Table. Width of table= 89.0 cm, Depth=44.5 cm, height=44 cm. OEM should be Green Guard and BIFMA Certified.

Providing and Providing and Supplying 2 Seater Sofa .Width (W): 135.0 CM. Depth (D): 85.0 CM. Height (H): 90.0 CM. Seat Height (SH): 45.0 CM.The seat should be made of PU foam with Density 32 ± 2 kg/cu.mtr having an additional top layer of J PU foam with Density 28 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 23±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood OCP-QLTA-PL14-18 4. Dia 4mm zigzag spring assembly should be mounted in understruCture for support and additional cushioning purpose .t should be a welded assembly made in Stainless steel (grade SS 202) tube & plate. OEM should be Green Guard and BIFMA Certified.

Providing and supplying 3 seater Sofa. Width (W): 186 CM. Depth (D): 85.0 CM. Height (H): 90.0 CM. Seat Height (SH): 45.0 CM.The seat should be made of PU foam with Density 32 ± 2 kg/cu.mtr having an additional top layer of J PU foam with Density 28 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 23±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood OCP-QLTA-PL14-18 4. Dia 4mm zigzag spring assembly should be mounted in understruCture for support and additional cushioning purpose .t should be a welded assembly made in Stainless steel (grade SS 202) tube & plate. OEM should be Green Guard and BIFMA Certified.

Providing & Supplying BIFMA certified Cubicle. Main table work top size is 1500W1 x 600D1 & Side table work top size is 1050W2 x 400D2 mm. Panel thickness-52.4mm. Uprights and horizontals shall be made of aluminum extrusion having material AL96063-T6 & have average wall thickness of 1.2 mm & powder coated with epoxy-polyester powder. Fabricated bottom frame for 52.4mm shall comprise of L- Channels made of 2mm thick CRCA steel (IS:513), formed plates of 3mm thick HR steel (IS:2062) & ERW steel tube of size 35x15x1.6mm in oval cross section (IS:7138) welded together. This shall be coated with average 50 to 60 micron thickness of epoxy powder coating. This shall be bolted to the uprights with M6 screws. A block for 52.4mm panel’s thickness shall comprise of 38mm thick paper honeycomb with 3mm MDF on each sides and 0.6mm decorative laminate or fabric on both sides. Particle board framing shall be used on outer boundary of these blocks as well as intermediately at certain locations forming conduit for passing cables. These blocks (2nos.) will be located in the middle bands of the panels. The panel legs used for supporting panels. The height of a panel leg shall be 126mm. Panel legs shall be fabricated by CO2 welding MS Tube of section 38 mm x 25 mm (IS: 7138 ERW Tube) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler shall be fitted, which allows for adjustment of the height by 50mm. It will be coated with min. 45 micron thickness of epoxy powder coating. The single side legs shall be used for supporting panels & work surface on one side only. Single side legs shall be fabricated by CO2 welding MS Tube of section 38 mm x 25 mm (IS: 7138 ERW Tube) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler shall be fitted, which shall allow for adjustment of the height by 50mm. this shall be coated with min. 45 micron thickness of epoxy powder coating. Gable end panel shall be made of 18mm thick both side Pre laminated particle board of interior grade of approved shade conforming to IS: 12823. All the edges of panel shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. Cable duct shall be made from 0.8 mm thick M.S. CRCA Grade D as per IS: 513 - 1994. It is constructed with two parts, one is body & another is cover. It holds the cables & gives aesthetic appearance by covering all cables entry, which are moving upward to the panels. Size of Cable duct is 107mm W X 154 mm H X 21 mm D. TOP TILES: These tiles shall be slid in to the panels from top before fixing the top horizontal. These tiles shall be supported from top & bottom side with clips made from PP co polymer fitted in horizontal extrusion. Fabric magnetic tiles shall be fabric upholstered metal tiles in 0.6 mm thick G.I. Grade O as per IS: 277. The fabrics shall be upholstered with adhesives. Fabric tackable tiles shall be upholstered metal tiles in 0.6mm thick G.I. grade O as per IS: 277, with P.E. foam in the tile for tackablity. The fabric shall be upholstered with adhesives. White board tiles shall be made of 8.0 mm thick particle board conforming to IS: 12823 laminated with 0.6mm thick white glossy high pressure laminate on outer side & 0.6mm backing laminate on inner surface and will be having all its edges with minimum 0.5 mm thick PVC edging. BOTTOM TILES: All bottom tiles shall be press fitted on to the assembly frame of the panel with the help of snap on clips made of nylon-66 and support clips made from PP polymer. Plain Metal tiles shall be powder coated metal tiles in 0.8 mm thick M.S. CRCA Grade D as per IS: 513. ALUMINUM EXTRUSIONS: The top trims and end trims for 52.4 mm & 22.8 mm shall be made from aluminum extrusion having material AL96063-T6. All kinds of extrusions for 52.4 mm and 22.8 mm shall have average wall thickness of 1.2 mm & having finish of powder coating. Top trim in 52.4mm thick panel shall be press fitted on the horizontal extrusion & in 22.8mm thick panel it shall be slide fitted with the help of top trim connector made from PP copolymer 3530 grade. End trim for 52.4mm thick panel shall be slide fitted with the help of end trim connector made from 2.0mm thick M.S. CRCA Grade D as per IS: 513. End trim for 22.8 mm thick panel shall slide with the help of end trim connector made from nylon-66. STABILITY POST: End stability post shall be fitted at the end of the free panel, to avoid movement of freestanding panels. The post shall be made in two parts. 1. The MS post which shall be grouted to the floor with Hilti make anchor bolts. 2. A cover extrusion of aluminium alloy shall cover the grouted MS stability bracket. The top end of the extrusion shall be covered with a powder coated aluminum cap. PANEL JOINERY POST: The panels shall be joined to each other directly with 180O joinery or with the help of post to form different layouts. The types available are 90° 2 way, 3 way & 4 way, 120° 2 way, 3way & fin post 2way, 3way & 4way. The panel joinery post shall be made up of aluminium extrusion having material AL-96063-T6. It shall have average wall thickness of 1.2mm. It shall be coated with 50 to 60 micron thickness of epoxy powder coating. These joineries will be covered with die cast caps of powder coated aluminium alloy ADC 12. All the caps shall be press fitted on the respective extrusions. WORKTOP: Work top shall be made of 25mm thick prelaminated particle board interior grade (As per IS: 12823). Bottom shall have a backing laminate of minimum 0.6mm thickness. All the edges of work surface shall be provided with machine pressed 2 mm thick PVC Edge band glued with hotmelt EVA glue. Work top shall be mounted onto the partition panels for work stations by means of cantilever brackets made from 2.0 mm thick CRCA grade D steel as per IS:513-1994 duly pretreated and powder coated. The work surface shall be provided with circular (grommet) cut out of Dia.65mm as per the requirement, for passing of wires. These cut outs shall be provided with ABS covers. The Penta Return work surface shall be supported by the stiffener. The stiffener shall be fabricated from 2mm thick CRCA steel (IS: 513), plates of 5 mm & 3 mm thick HR steel (IS: 2062) & ERW steel tube of size 50X30X1.5 mm welded together. This stiffener shall connect to panel on one side and to Double Sided penta return leg on the other side. Work surface bracket shall be mounted on to the Horizontal extrusion. Work surface bracket shall be made from 2.0 mm thick CRCA grade D steel as per IS: 513-19. Ribs shall be provided in the bracket for strengthening purpose. All the work surface are mounted on the work surface brackets. Holder bracket shall be made from 2.0 mm thick CRCA grade D steel as per IS: 513-19. It shall slid in between end trim & vertical extrusion, & mounted on work surface with the help of pop rivet. Seating arrangement includes metal key board tray, CPU trolly and Nova free standing pedestal with central locking and flat metal front of size 390W x 435D x 646HT, 3dr=2box+1file. Approved Make: Godrej / Herman Miller / Haworth / Knoll / Equivalent

Providing & Supplying BIFMA certified Penta workstation of size 1800W1 x 1500W2 x 600D. Panel thickness-52.4mm. Uprights and horizontals shall be made of aluminum extrusion having material AL96063-T6 & have average wall thickness of 1.2 mm & powder coated with epoxy-polyester powder. Fabricated bottom frame for 52.4mm shall comprise of L- Channels made of 2mm thick CRCA steel (IS:513), formed plates of 3mm thick HR steel (IS:2062) & ERW steel tube of size 35x15x1.6mm in oval cross section (IS:7138) welded together. This shall be coated with average 50 to 60 micron thickness of epoxy powder coating. This shall be bolted to the uprights with M6 screws. A block for 52.4mm panel’s thickness shall comprise of 38mm thick paper honeycomb with 3mm MDF on each sides and 0.6mm decorative laminate or fabric on both sides. Particle board framing shall be used on outer boundary of these blocks as well as intermediately at certain locations forming conduit for passing cables. These blocks (2nos.) will be located in the middle bands of the panels. The panel legs used for supporting panels. The height of a panel leg shall be 126mm. Panel legs shall be fabricated by CO2 welding MS Tube of section 38 mm x 25 mm (IS: 7138 ERW Tube) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler shall be fitted, which allows for adjustment of the height by 50mm. It will be coated with min. 45 micron thickness of epoxy powder coating. The single side legs shall be used for supporting panels & work surface on one side only. Single side legs shall be fabricated by CO2 welding MS Tube of section 38 mm x 25 mm (IS: 7138 ERW Tube) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler shall be fitted, which shall allow for adjustment of the height by 50mm. this shall be coated with min. 45 micron thickness of epoxy powder coating. Gable end panel shall be made of 18mm thick both side Pre laminated particle board of interior grade of approved shade conforming to IS: 12823. All the edges of panel shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. Cable duct shall be made from 0.8 mm thick M.S. CRCA Grade D as per IS: 513 - 1994. It is constructed with two parts, one is body & another is cover. It holds the cables & gives aesthetic appearance by covering all cables entry, which are moving upward to the panels. Size of Cable duct is 107mm W X 154 mm H X 21 mm D. TOP TILES: These tiles shall be slid in to the panels from top before fixing the top horizontal. These tiles shall be supported from top & bottom side with clips made from PP co polymer fitted in horizontal extrusion. Fabric magnetic tiles shall be fabric upholstered metal tiles in 0.6 mm thick G.I. Grade O as per IS: 277. The fabrics shall be upholstered with adhesives. Fabric tackable tiles shall be upholstered metal tiles in 0.6mm thick G.I. grade O as per IS: 277, with P.E. foam in the tile for tackablity. The fabric shall be upholstered with adhesives. White board tiles shall be made of 8.0 mm thick particle board conforming to IS: 12823 laminated with 0.6mm thick white glossy high pressure laminate on outer side & 0.6mm backing laminate on inner surface and will be having all its edges with minimum 0.5 mm thick PVC edging. BOTTOM TILES: All bottom tiles shall be press fitted on to the assembly frame of the panel with the help of snap on clips made of nylon-66 and support clips made from PP polymer. Plain Metal tiles shall be powder coated metal tiles in 0.8 mm thick M.S. CRCA Grade D as per IS: 513. ALUMINUM EXTRUSIONS: The top trims and end trims for 52.4 mm & 22.8 mm shall be made from aluminum extrusion having material AL96063-T6. All kinds of extrusions for 52.4 mm and 22.8 mm shall have average wall thickness of 1.2 mm & having finish of powder coating. Top trim in 52.4mm thick panel shall be press fitted on the horizontal extrusion & in 22.8mm thick panel it shall be slide fitted with the help of top trim connector made from PP copolymer 3530 grade. End trim for 52.4mm thick panel shall be slide fitted with the help of end trim connector made from 2.0mm thick M.S. CRCA Grade D as per IS: 513. End trim for 22.8 mm thick panel shall slide with the help of end trim connector made from nylon-66. STABILITY POST: End stability post shall be fitted at the end of the free panel, to avoid movement of freestanding panels. The post shall be made in two parts. 1. The MS post which shall be grouted to the floor with Hilti make anchor bolts. 2. A cover extrusion of aluminium alloy shall cover the grouted MS stability bracket. The top end of the extrusion shall be covered with a powder coated aluminum cap. PANEL JOINERY POST: The panels shall be joined to each other directly with 180O joinery or with the help of post to form different layouts. The types available are 90° 2 way, 3 way & 4 way, 120° 2 way, 3way & fin post 2way, 3way & 4way. The panel joinery post shall be made up of aluminium extrusion having material AL-96063-T6. It shall have average wall thickness of 1.2mm. It shall be coated with 50 to 60 micron thickness of epoxy powder coating. These joineries will be covered with die cast caps of powder coated aluminium alloy ADC 12. All the caps shall be press fitted on the respective extrusions. WORKTOP: Work top shall be made of 25mm thick prelaminated particle board interior grade (As per IS: 12823). Bottom shall have a backing laminate of minimum 0.6mm thickness. All the edges of work surface shall be provided with machine pressed 2 mm thick PVC Edge band glued with hotmelt EVA glue. Work top shall be mounted onto the partition panels for work stations by means of cantilever brackets made from 2.0 mm thick CRCA grade D steel as per IS:513-1994 duly pretreated and powder coated. The work surface shall be provided with circular (grommet) cut out of Dia.65mm as per the requirement, for passing of wires. These cut outs shall be provided with ABS covers. The Penta Return work surface shall be supported by the stiffener. The stiffener shall be fabricated from 2mm thick CRCA steel (IS: 513), plates of 5 mm & 3 mm thick HR steel (IS: 2062) & ERW steel tube of size 50X30X1.5 mm welded together. This stiffener shall connect to panel on one side and to Double Sided penta return leg on the other side. Work surface bracket shall be mounted on to the Horizontal extrusion. Work surface bracket shall be made from 2.0 mm thick CRCA grade D steel as per IS: 513-19. Ribs shall be provided in the bracket for strengthening purpose. All the work surface are mounted on the work surface brackets. Holder bracket shall be made from 2.0 mm thick CRCA grade D steel as per IS: 513-19. It shall slid in between end trim & vertical extrusion, & mounted on work surface with the help of pop rivet. Seating arrangement includes metal key board tray, CPU trolly and Nova free standing pedestal with central locking and flat metal front of size 390W x 435D x 646HT, 3dr=2box+1file. Approved Make: Godrej / Herman Miller / Haworth / Knoll . / Equivalent

Providing and supplying Godrej Topaz Work Surface-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Gromet provided on work surface for wire management.Modesty Panel-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Under-structure-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconfirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Hinge Door Storage-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconfirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Handle is provided for ease of opening.Storage is provided with cam lock for security. OEM should be Green Guard and BIFMA Certified Providing and Supplying Godrej Aristo Back unit Top Panel-Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Slide Door Unit-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves.Shutters are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening.Storage is provided with lock for security. Display/Storage Unit-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side,back and shelves.Doors are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Top panel of display unit Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. OEM should be Green Guard and BIFMA Certified. Table (1650x1950x750)

Table (1800x900x750)

Reparing of Chair

Repairing of Executive Chair

Core Cutting 75mm Dia ,Depth Upto 300mm etc complete as directed.

Dismantaling & Repairing With Finishing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointingcompound.

Celling & Wall painting (three coats) with one coat of BIRLA WHITE primer & BIRLA WHITE putty & with plastic emulsion paint of Asain royale, ICI velvet touch brand, Berger , Nerolac or equivalent and manufacture on wall surfaces to give an even shade including thouroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth at all floor level and as directed by Engineer-in-charge etc. complete including all material and labour.

I. T. Work Supply, Installation, Testing and Commissioning MATRIX IP PBX MODAL .NO = EXTERNITY PE 6 S CONFIGURATION = 4X24 as per direction executive in charge.

Providing , supplying and fixing One time Installation Charge etc as complete as directed.

Supply and Fixing decorative 3mm thick S.S. Name Plate With CNC Cutting Size of 30" x 9".

Providing and fixing name/sign plate of thicness 1.5mm thick digital Eco Night Glow Printing with UV Matt Lamination & Acrylic Sheet and size (12" x 6")with text and graphics made of Acrylic including fixing with gum etc complete as per design given by the architect and approved by the engineer in charge.

Providing , supplying and fixing HDMI Extender(HDMI Extender transmits digital video and audio signals up to 150 feet .

Providing , supplying and fixing Firewall Router make of Cisco or ASUS, Model No. RV042-EU Dual fast ethernet wan Port for load balancing and/ or business continuity, High' capacity VPN Capabilities, strong security.

Supply, Installation, Testing and Commissioning 5 PORT DESKTOP SWITCH of approved make and model etc as directed.The D-Link DGS-1005A 5-Port Gigabit Desktop Switch provides a convenient way to share a home or small office network connection with up to four other.

Supply, Installation, Testing and Commissioning CAT-6-(2PAIR) WIRE etc as directed. (A standardized twisted pair cable for Ethernet and other network.).

Supply, Installation, Testing and Commissioning HDMI SPLITTER etc of standard make and model as directed.(An HDMI splitter allows you to plug two devices into one HDMI input and switch between them without the hassle of unplugging cables.).

Providing , supplying and fixing 20 PAIR TELEPHONE CABLE(12MM) etc as directed.(Polyester taped and sheathed with high oxygen index Fire compound • High density polyethylene insulated • Solid annealed high conductivity bare copper).

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as directed.

Providing , supplying and fixing D-Link Cat-6 Wire 302 mtr/box etc. of approved make and model etc as directed.

Providing, supplying and fixing D-LINK 16 PORT LAN SWITCH of approve make and model etc as directed.(The 16-Port Unmanaged Gigabit Switch brings the speed of Gigabit Ethernet to each and every port for a truly high-speed network.).

Providing, supplying and fixing 50 MBPS lease line Internet 760 per MB of standard approved brand etc. and service for six floor for 12th months after completion of work as directed by engineer in charge.

HVAC Supply, Installation, Testing and commissioning (SITC) normal size( as directed by Engineer In Charge) Cassete type room/indoor unit having Four sides air flow 2.8 TR capacity suitable to work with cordless/Centralised Remote arrangement VRF system having motorised Drain water arrangement working on 230 V, 50 cycles, A.C. supply complete at position as per drection. The Cassete type indoor units shall be ceiling mounted suspended with required size/capacity Full threaded Solid GI Rod Anchor Fastner Arrangement at four corners. The indoor unit must have electronic expansion valve operated by microprocessor thermostat based tempreture control to deliver cooling as per manufacturers standard specifications. Make : Bluestar / Daikin / Mitsubishi.

Supply, Installation, Testing and commissioning (SITC) normal size( as directed by Engineer In Charge) Cassete type room/indoor unit having Four sides air flow 2.0 TR capacity suitable to work with cordless/Centralised Remote arrangement VRF system having motorised Drain water arrangement working on 230 V, 50 cycles, A.C. supply complete at position as per drection. The Cassete type indoor units shall be ceiling mounted suspended with required size/capacity Full threaded Solid GI Rod Anchor Fastner Arrangement at four corners. The indoor unit must have electronic expansion valve operated by microprocessor thermostat based tempreture control to deliver cooling as per manufacturers standard specifications. Make : Bluestar / Daikin / Mitsubishi.

Supply, Installation, Testing and commissioning (SITC) of fully Indiginous factory assembled variable refrigerant flow (VRF) unit. The unit shall be complete with the following capacity outdoor unit - Multiple(minimum two) Inverter scroll compressors with both Compressors are controlled by DC inverter Technology - Micro processor based unit mounted compressor starter/ control panel with suitable rain protection covers -Built in oil seperator, accumulator & oil receiver, -Suitable for longer piping length upto 1000 m -sutable to work on 3 phase 415 volts 50HzA.C Supply - Complete with necessary R410A Refrigerent Gas Charging as per the site condition for satisfactory operation entire system complete with testing for leakages as per OEM Specs. 22 hp - Air cooled condenser coil-Squore shaped heat exchanger to increase heat transfer area, high COP & lower power consumption with fan, motor and starter. - Controls comprising HP/ LP cutout, cooling thermostats etc. -Remote Monitoring Facility for all recording the Parameters/Performnace of the System in OEM's Service Centre & attending breakdown calls accordingly - Interconnecting copper piping, valves, power wiring, control wiring and earthing. -constructed from polysterpowder coated sheet metal housing Equipment supplied shall be of non chinese make origin -The ODu's are designed so that at 42Deg Centigrade Ambient Temperature the unit shall able to work at 100%capacity Make : Bluestar / Daikin / Mitsubishi. (A) 22 Hp

Supplying, erecting, Testing & commissioning Centralised programmable Remote contol Panel which controls minimum 16System of 64 ODU's can be controlleed & up to 992 IDU's can be individually mounted & controlled indoor units having colour min 200mm size LCD touch panel,yearly schedule, Power propotional distribution function,temperature limitation, History function complete erected on wall integrated with Fire Alarm System.

Supplying, erecting, Testing & commissioning wireless Remote contol having colour LCD panel, Real Time Clock,temperature limitation(16 to 30Deg Cent., Functions Like Filter Clean reminder Timer suitable to communicate with wired controller complete.

Supply, Installation of high pressure grade required size Copper Connection Y/T-Joints/refnut complete with brazing Testing for leakages, erected on wall/ceiling with supports/raceways, Nitrile rubber insulation, painting etc. For Indoor Units.

Supply, Installation of high pressure grade required size Copper Connection Y/T-Joints/refnut complete with brazing Testing for leakages, erected on wall/ceiling with supports/raceways, Nitrile rubber insulation, painting etc. For Outdoor Units.

Supply and laying of high pressure grade Hard drawn Copper refrigeration pipe, having minimum 1mm thickness with required size Nitrile rubber insulation complete with brazing Testing for leakages, erected on wall/ceiling with GI Hanger supports/raceways, with, painting etc. ( Pipe Sizes as per manufactures designs.. Vendor to Obain Manufactur's Approval on sizing before starting the work) .

Supplying & erecting PVC cable 2 core 1 sq mm copper conductor with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/CU FOR Corded Remote.

Supplying, and charging Addl fresh eco-friendly refrigrent gas R410A to the VRF/VRV System in an approved manner .

Supplying Laying and testing of rigid UPVC conduit 25 mm dia. with PVC accessories on wall /ceiling as per specification for Drain Pipe complete with Elastomeric Nitrile rubber / foam tube type sleeves for over coating and insulating on provided copper pipes having 9 mm thickness and inner diameter / sizes 25 mm as per specification no ESD-ENR.

Supplying and erecting rigid UPVC conduit 32 mm dia. with PVC accessories on wall /ceiling as per specification for Drain Pipe complete with Elastomeric Nitrile rubber / foam tube type sleeves for over coating and insulating on provided copper pipes having 9 mm thickness and inner diameter / sizes 32 mm as per specification no ESD-ENR.

Supplying and erecting rigid UPVC conduit 40 mm dia. with PVC accessories on wall /ceiling as per specification No: WG-MA/CON, para no. 1.1.1 for Drain Pipe complete with Elastomeric Nitrile rubber / foam tube type sleeves for over coating and insulating on provided copper pipes having 9 mm thickness and inner diameter / sizes 50 mm as per specification no ESD-ENR.

Supplying & Providing thermal UnderDeck insulation Elastomeric foam CLASS-O - 32mm Thk.

Electrical Work Supplying and erecting Iron work consisting of Various sections of MS and including Plates, Chequered Plates, Rods, Bars, MS pipes, etc. for panel board or any other purposes complete with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority for ODU .

Supplying erecting testing and commissioning of LT MCCB cubicle control panel for VRF Out door systems load distribution made up of CRCA sheet of 16 SWG for housing with IP65 grade as per drawing attached or instructions of engineer in-charge Or specification given by Manufacturer.

Supplying erecting testing and commissioning of LT MCCB cubicle control panel for VRF AC system load distribution made up of CRCA sheet of 16 SWG for housing with IP65 grade protection 01 nos. with 4P MCCB with cable alleys as per drawing attached or instructions and specification to be approved by engineer in-charge. incorporating the following of componants

Supplying & erecting PVC copper armoured cable 4 core 6 sq mm complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/CU .

Supplying & erecting PVC copper armoured cable 4 core 16 sq mm complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/CU.

Supplying & erecting PVC cable 3 core 1.5 sq mm copper conductor with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/CU FOR Corded Remote.

Supplying and erecting G.I. strip 25* 3 mm of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint in an approved manner with joint required. as per specification No (EAEP)

G.I. 10 Gage earthing wire draw with each and every cable.

Supply Installation of MCCB'S near ODU as per manufacturer specification.

Supply Installation of MCB'S near IDU as per manufacturer specification.

Minor civil work such as wall Opening and chasing, chislling etc.

Supplying & erecting UPVC Mini trunking (PVC Casing-n-Capping) having double-locking arrangement with grooves, trunking of size not below 12.5 mm in height as per IS with accessories of PVC/Resin polypropylene not below 1.8 mm thick duly sealed in joint & erected on wall/celling of following size. (4) 40 mm

Mains with 1.1 KV grade FRPVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in / flushed on wall/ ceiling, with 1.5 sq. mm. copper conductor FR PVC insulated stranded wire of green colour for earth continuity of following size. a) with medium class Rigid PVC pipe and accessories. (a) 2 wire 1.5 sq. mm.

Supplying & erecting approved make Telephone Cable electrolytic copper conductor PE insulation twisted in two pairs & wrapped with FR PVC tape & sheathed with FR PVC or HFFR outer jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following size of conductors & nos. of pairs. With necessary connections. A Conductor Size 0.5 mm. (a) Unarmoured. (b) Two Pairs.

Providing following type of Modular Type Accessories mounted with pvc / metallic box covered with appropriate front plate modules erected with necessary connection. As desired by Engineer In charge. (1) One No. SP 6 Amp Cat. III

Providing following type of Modular Type Accessories mounted with pvc / metallic box covered with appropriate front plate modules erected with necessary connection. As desired by Engineer In charge. (2)One No. 5 pin plug Cat. III

Providing following type of Modular Type Accessories mounted with pvc / metallic box covered with appropriate front plate modules erected with necessary connection. As desired by Engineer In charge. (3) Two Pin/RJ - 11 Telephone Socket (A) For One Gang

Providing following type of Modular Type Accessories mounted with pvc / metallic box covered with appropriate front plate modules erected with necessary connection. As desired by Engineer In charge. (7) Blank plate single.

Providing following type of Modular Type Accessories mounted with pvc / metallic box covered with appropriate front plate modules erected with necessary connection. As desired by Engineer In charge. (8) Modem Jack for Computer Open RJ-45

Providing & erecting Switch board for Computer or electric apparatus consisting of following items in single board erected on PVC / Metal board with 3mm thick PC (Polycarbonate) / Acrylic sheet erected as directed “1 no. 6A/16A universal plug – switch combined 4 nos. 6A switch 4 nos. 6A 5 pin Plug.[B] For Modular Type Accessories CAT. III

Providing & erecting 415V MCD Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS: 8828 in existing box having following capacity. (b) 40 Amp Cat. III.

Supplying and erecting testing and commissioning of LT MCCB cubicle main control panel for VRF AC System load distrivbution made up of CRCA sheet of 16 SWG for hopusing with IP - 54 grad protection 01 nos. 300A micro processor based 4P, ACB, 15 KA MDO with cable alleys as per drawing attached or instruction of engineer in charge and specification given by the manufacturer.

Anand Associates

SUPER CONSTRUCTION

Dharmik Construction

SHIRISH RAMANLAL SHARMA