REPAIRS REPLACEMENT OF STREET SECURITY LIGHT PATHWAY LIGHTS HIGH MAST LIGHT GARDEN LIGHT POST TOP LANTERN JUNCTION BOXES AND DISTRIBUTION CABLE OF IN LOW RISE BLDG AREA OF OLD AND NEW NAVY NAGAR UNDER GE NW NAVY NAGAR

Amount

Taking down defective street light fitting of any size/ type/ capacity from height of pole/walls/high mast of any location exceeding 3.0 m height for repair work and re-fixing back after repair work including checking, inspecting, testing and commmissioning complete all as directed by Engr-in-Charge. Note:a) The M/L for Items like electronic drivers,surge protection devices etc shall be measured and paid separately under relevant items here in under this Schedule as supply only. b) Necessary tools like ladders & other T&P required etc shall be arranged by the Contractor. c) The rate quoted deemed to be inclusive for minor parts nut bolts, circle clips, clamps etc if any required at site.d) The M/L for repairs to LED panel is not included in the scope and shall be measured and paid separately.

Supply only the following spares suitable for LED street/Flood light fittings of

Electronic driver suitable for outdoor LED fitting of capacity 200 to 400 Watt.

Electronic driver suitable for outdoor LED fitting of capacity 120 to 180 Watt.

Electronic driver suitable for outdoor LED fitting of capacity 70 to 110 Watt.

Electronic driver suitable for outdoor LED fitting of capacity 30 to 60 Watt.

Surge protection device compatible with industrial & outdoor LED fitting of capacity 10 KV complete all as specified and as directed.

Surge protection device compatible with industrial & outdoor LED fitting of capacity 5 KV complete all as specified and as directed.

Dismantling LED light fitting of of Make:Bajaj /Crompton/ Phillips/ Havells/ Wipro/Orient/C&S/Polycab/Shakti Henolix of capacity 200 to 400 W ,strip opening the elctronic driver, LED panel complete, identifying defective LEDs , replacement of defective LEDs complete including soldering, replacement of pitted control wiring from LED panel to driver etc complete, including testing and commissioning complete. Note : The rate quoted is not inclusive of taking down and refixing of street light fittings and shall be measured and paid separately under relevant schedule items

All as per item No- 3.00 here in before but of capacity 120 watt to 180 watt.

All as per item No- 3.00 here in before but of capacity 70 watt to 110 watt.

All as per item No- 3.00 here in before but of capacity 30 watt to 60 watt.

Taking down old unserviceable security light fittings from any height and Supply & fixing LED security light fittings comprising of epoxy powder coated housing, enclosed with glass cover in frame,(with suitable wattage for efficiency not less than 100 lumens/Watt) min wattage 45 watt, with ingress protection IP 65/66 and SPD of capacity 5 KV etc incl necessary clamps etc complete and testing on completion all as specified and as directed. Note: The GI pipe bracket if required will be measured and paid separately under relevant schedule items.

Taking down old unserviceable security light fittings from any height and Supply & fixing LED security light fittings comprising of epoxy powder coated housing, enclosed with glass cover in frame,(with total lumen output not less than 6000 lumens and suitable wattage for efficiency not less than 100 lumens/Watt) min wattage 60 watt, with ingress protection IP 65/66 and SPD of capacity 5 KV etc incl necessary clamps etc complete and testing on completion all as specified and as directed. Note: The GI pipe bracket if required will be measured and paid separately under relevant schedule items.

Taking down old unserviceable security light fittings from any height and Supply & fixing LED security light fittings comprising of epoxy powder coated housing, enclosed with glass cover in frame,(with total lumen output not less than 7200 lumens and suitable wattage for efficiency not less than 100 lumens/Watt) min wattage 72 watt, with ingress protection IP 65/66 and SPD of capacity 5 KV etc incl necessary clamps etc complete and testing on completion all as specified and as directed. Note: The GI pipe bracket if required will be measured and paid separately under relevant schedule items.

Taking down old unserviceable security light fittings roadway lumanarie type from any height and Supply & fixing LED security light fittings comprising of epoxy powder coated housing, enclosed with glass cover in frame,(with total lumen output not less than 9000 lumens and suitable wattage for efficiency not less than 100 lumens/Watt) min wattage 90 watt, with ingress protection IP 65/66 and SPD of capacity 5 KV etc incl necessary clamps etc complete and testing on completion all as specified and as directed. Note: The GI pipe bracket if required will be measured and paid separately under relevant schedule items.

Taking down old unserviceable security light fittings roadway lumanarie type from any height and Supply & fixing LED security light fittings comprising of epoxy powder coated housing, enclosed with glass cover in frame,(with total lumen output not less than 11000 lumens and suitable wattage for efficiency not less than 100 lumens/Watt) min wattage 120 watt, with ingress protection IP 65/66 and SPD of capacity 10 KV etc incl necessary clamps etc complete and testing on completion all as specified and as directed. Note: The GI pipe bracket if required will be measured and paid separately under relevant schedule items.

Taking down old unserviceable flood light fittings from any height and Supply & fixing LED flood light fittings comprising of epoxy powder coated housing, enclosed with glass cover in frame,(with total lumen output not less than 12000 lumens and suitable wattage for efficiency not less than 100 lumens/Watt) min wattage 120 watt, with ingress protection IP 65/66 and SPD of capacity 10 KV etc incl necessary clamps etc complete and testing on completion all as specified and as directed.

Taking down old unserviceable flood light fittings from any height and Supply & fixing LED flood light fittings comprising of epoxy powder coated housing, enclosed with glass cover in frame,(with total lumen output not less than 20000 lumens and suitable wattage for efficiency not less than 100 lumens/Watt) min wattage 200 watt, with ingress protection IP 65/66 and SPD of capacity 10 KV etc incl necessary clamps etc complete and testing on completion all as specified and as directed.

Taking down old unserviceable flood light fittings from any height and Supply & fixing LED flood light fittings comprising of epoxy powder coated housing, enclosed with glass cover in frame,(with total lumen output not less than 25000 lumens and suitable wattage for efficiency not less than 100 lumens/Watt) min wattage 250 watt, with ingress protection IP 65/66 and SPD of capacity 10 KV etc incl necessary clamps etc complete and testing on completion all as specified and as directed.

Taking down old unserviceable flood light fittings from any height and Supply & fixing LED flood light fittings comprising of epoxy powder coated housing, enclosed with glass cover in frame LED type (with total lumen output not less than 35000 lumens and suitable wattage for efficiency not less than 100 lumens/Watt) min wattage 350 watt, with ingress protection IP 65 and surge protection device of 10 KV capacity etc incl necessary, angle iron supports , clamps etc complete and testing on completion all as specified and as directed.

Taking down old unserviceable flood light fittings from any height and Supply & fixing LED flood light fittings comprising of epoxy powder coated housing, enclosed with glass cover in frame LED type (with total lumen output not less than 40000 lumens and suitable wattage for efficiency not less than 100 lumens/Watt) min wattage 400 watt, with ingress protection IP 65 and surge protection device of 10 KV capacity etc incl necessary, angle iron supports , clamps etc complete and testing on completion all as specified and as directed.

Supply & fix replacement decorative path way light lighting LED decorative post top lantern for 360 degree 40 watts 230 volts, 50 HZ, maple shaped in sothing opal/ prismatic finish made up of polycarbonate,including all accessories prewired complete.Note :- (i) Minimum 2 years gaurntee period of LED fittings (ii) Driver shall be IP 66 degree of protection potted seal type. (iii) Power factor more than 0.9.

Supply and erect steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-31 (9.0 metres long) all as directed incl dismantling old one. NOTE :- Earth work, Cement concrete in foundation, coping etc will be measured and paid separately under relevant item.

Supply and erect steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-55 (11.0 metres long) all as directed incl dismantling old one. NOTE :- Earth work, Cement concrete in foundation, coping etc will be measured and paid separately under relevant item.

Supply, laying and commissioning, testing armoured heavy duty electric cable with copper conductor, 1100 volts grade of size 4 sqmm 4 core laid in trenches, passing through pipes, fixed on walls complete including connecting properly by means of thimbles/bottle lugs and taking out old u/s damaged cables.

All as per item No- 20.00 here in before but of size 2.5 sqmm 3 core including taking out old u/s damaged cables.

All as per item No- 20.00 here in before but of size 1.5 sqmm 2 core including taking out old u/s damaged cables.

M&L for PCC 1:4:8 type D2 with 40 mm graded aggregate as in foundation complete.

M&L for PCC 1:3:6 type C1 with 20 mm graded aggregate for coping of poles and stay including form work.

S & F as in repair astronomical Timelite distribution board IP-54 with contactor, relay and prewired, 32A, 3 pole, 230 Volt , and Astronomical programmable time switch with backup of 6 years, 28 memory locations, current capacity 16 A with one CO time switches for street light complete.

S & F in repairs digital time switch 3 phase of current capacity 16 Amps incl any type of accessories with suitable capacity of contactor after taking out unserviceable one.

S & F in repair 3 pole power contactor with coil voltage 230 volt AC of current carrying capacity 32 to 40 Amps complete including control wiring thimbles etc complete all as directed.

M&L for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using 4 mm dia GI earth wire bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth wire encased in and including 15 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion. Note :- If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department.

S&F loop-in/loop-out box of outer size size 225mmx295mmx122mm made out of FRP(Hot moulded type) with weather proof canopy and locking screws along with with 5/6 Amps MCB - 01 No, 50 Amps rated 3 pole connector- 01 Nos, neutral link mounted and Din rail suitable size for mounting MCB/Connector etc complete in the box, duly fixed to to steel tubular/rail/PCC/RCC pole using 25 x 3mm aluminium clamp not less than, including suitable gland and lugs for connecting cable complete all as directed including dismantling old one.

S&F in repair thermoplastic cable junction water proof boxes of 130x130x77mm, with metric knockouts for cable entry and suitable size of gland for 4 to 10 Sqmm cable out door type with clamp for mounting on pole complete all as specified and as directed.

S&F street light bracket bend to shape made as required of 32/40mm dia 1 mtr long GI pipe light grade fixed to pole/wall with flat iron clamp of size 40x6mm two number with the help of nuts and bolts for fixing of street light fitting including making all electric connection including taking out old one complete all as specified and as directed.

M&L for preparation of old painted steel surfaces of 9 m long steel poles incl removing oily/greasy spots and applying one coat of aluminium paint complete including applying a coat of white wash on pole coping and lettering the pole details with white letters/ blackground etc complete all as directed

Repairs to High Mast/mid mast pole motor of Capacity 1.0 HP/0.75 KW 415 Volts 50 Hz 3 Phase 930 RPM and necessary rewinding with super enamelled copper wire all as per existing and servicing/greasing of reduction gear box complete all as specified and as directed by Engr-in-Charge.

Decarbonising of the control panel of High mast/Mid mast and including sevicing of parts such as contactors/timers including replacement of pitted lugs,thimbles, control wiring etc complete including painting with a coat of synthetic enamel paint

Excavation in trenches not exc 1.5 mtr wide and not exc1.5 mtr in depth for laying of cables etc. in any type of soil and getting out all as specified and directed by Engineer-in-Charge. Note : Rate includes removing of paver blocks carefully and stack properly for refixing after laying of cables .

All as per above item No.35 above but exceeding depth 1.5 mtr and n exceeding 3 mtrs.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm in soils.

Removing excavated material from the site of work and transporting out of Station/site of work suitable to the contractor all as specified.

Material and labour for 60 mm thick coloured interlocking paver tiles/ blocks, lacquer finish of size 250x250 mm having compressive strength of 35N/Sqmm, zig-zag (uni-paver) shape in flooring tested as per IS : 15658-2006, with and including layer of 50 mm thick natural river sand bed compacted complete as specified and directed.

Cutting existing road surfaces or hard standing 0.45 mtr depth (22 thick comprising bituminuous topping) and width upto 45 cm for laying of pipes/cables and making good disturbed surfaces to match with existing surfaces.

Material and labour for cement concrete type C-2, 1:3:6 (40mm graded stone aggregate), for coping and finished surface without using extra cement.

Supplying and laying with commissioning and testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade of size 50 sqmm 3.5 core laid in trenches, passing through pipes, fixed on walls complete including connecting properly by means of thimbles and taking out old u/s damaged cables.

All as per Item No-42.00 here in before but of sizes, 35 sqmm, 3.5 core.

All as per Item No-42.00 here in before but of sizes, 25 sqmm, 3.5 core.

All as per Item No-42.00 here in before but of sizes, 16 sqmm, 4 core.

All as per Item No-42.00 here in before but of sizes, 10 sqmm, 4 core.

All as per Item No-42.00 here in before but of sizes, 10 sqmm, 2 core.

M&L for 50mm dia High density poly-ethylene pipes (HDPE) of pressure 6 kgf/cm2 pipe, for cable protection laid in trenches or above ground surface including taking down all as specified and directed.

All as per Item No-48.00 here in before but of sizes, 75mm dia

M&L for GI pipe ,light grade 50mm dia for road crossing or in hard standing for protection of cable above or under ground surface including taking out old one all as specified and directed.

All as per Item No-50.00 here in before but of sizes, 80mm dia

Supply and fixing LED Column Light 50 watt, 4 mtr height with die-cast aluminum pipe housing with cylindrical opal polycarbonate diffuser designed for rugged outdoor usage & IP 65 protection with Tricolor and tratic white output switch mounted on PCC block including connection copper wire of required length (not more than 2 mtr), connector and thimble/lugs etc including taking down old one complete all as specified and directed.

S&F Decorative Ornamental Cast iron Pole of height 3 Mtr with base dia of 200mm, bottom-210mmx450mm above the foundation top level fabricated with cast iron embellishment, joints, column sections etc re-inforced internally with a MS pipe inside and inbuilt looping box for incoming and outgoing UG cable. The pole shall have cast iron design for double arm bracket . The pole shall be painted with polyurethane paint of approved colour finish including fixing and grouting to old existing foundation with the help of Nuts, bolts and washer, making all electrical conection to light fitting after taking out old CI pole and necessary PCC work, all as directed. Make- EYE-Lite luminaires or equivalent as per sample

S&F CI casted two way bracket with centre hub for mounting on 3 mtr deco ornamental pole suitable for fixing LED decorative lantern fitting of 14/15 Watt and making all electrical connection to the light after taking out old U/S.

S&F Post type LED decorative lantern fitting 19"x11" of 14/15 Watt IP 65 with spun aluminium housing and reflector assembly with polycarbonate/Glass cover with protection for optical compartment complete including taking out old U/S.

S&F Decorative Ornamental Cast iron Pole of height upto 2.5 Mtr with base dia of 200mm, bottom-210mmx450mm with cast iron embellishment, joints, column sections with cross cutting groves etc cast iron design with cast iron designed double arm bracket for lantern. The pole shall be painted with polyurethane paint of approved colour finish including fixing and grouting on round PCC plateform of 60cm above ground level with the help of Nuts, bolts and washer, making all electrical conection to light fitting after taking out old CI pole and necessary PCC work, all as directed.

S&F Decorative Alluminium casted, powder coated lantern of size 21"x9" for decorative ornamental poles with holder for LED Lamp and with 6 Nos of Polycarbonate/frosted Glass for optical compartment as per sample and reconnecting all electrical connection to light complete including taking out old U/S.

S&F in replacement with new LED pin type lamp of 14 watt warm white after opening of post type lantern fitting from deco pole and checking of all electrical connection and refixing the lantern cover on its existing arm of deco pole.

S&F Aluminium casted pole of 1 Mtr long, powder coated with foundation bracket and holder for mounting of decorative Garden light including necessary PCC plateform for grouting pole and reconnecting all electrical connection to light complete including taking out old U/S.

Supply and fixing as in repair Frosted Glass suitable for optical compartment of Decorative light fittings (As per sample) approved by Engr-in-Charge.

Supply and fixing LED based bollard light 9 watt with MS pipe housing with glare free PMMA diffuser,IP-65 complete with necessary PCC foundation and PCC block of 60cm height above ground including taking out old, U/S complete all as directed.

S&F Integral decorative LED 45 Watts Post Top with opal acrylic with IP65 Protection mounted on 1 Mtr GI pole complete with necessary PCC foundation and PCC block of 60cm height above ground including taking out old, U/S complete all as directed.

All as per item No - 62.00 above but LED Post Top lantern 20 watt.

S&F in replacement of 20 watt LED RGB under water light IP68 luminaire, size - 190mmx250mm with stainless steel housing with driver including necessary stand for fixing of fountain light with mounting base including making all electrical connection complete.

All as per item No - 64.00 above but LED RGB under water, 12 watt.

S&F in replacement with LED fasad batten light of 36 watt, 4 feet with RGB wall washer made up of pressure die cast housing with aluminium LED with lense, IP-65, with stand and cover including driver and remote control operated including frame for mounting of light as required and making all electrical connection complete all as directed.

All as per item No - 66.00 above but LED fasad batten light of 2 feet, 18 watt.

S&F manual operated security search light complete with brass body including LED 200 watt lamp with lens, handle for rotation of search light luminous flux 26000, operating temperature 20 deg C to 60 deg C, IP-65 protection, working humidity 5% to 95% RH of range cover 250 Mtr, THD<10%, power factor>0.95, CRI>70, mounting base cap, reflector complete system including taking out U/S complete all as directed.

Sri Krishna Construction (BID ID -3467288)

SUNRISE CONSTRUCTION CO (BID ID -3469621)

shubham construction (BID ID -3469277)

S S ENTERPRISES (BID ID -3465536)