Construction of Clean Plant Centre Laboratory and Office Building at ICAR-CITH, Srinagar

Amount on Amount on Total Amount

Grand Total (DSR+NDSR) Rs. 19,90,43,747.00

GENERAL ABSTRACT OF COST

DSR 2023 DESCRIPTION Unit Qty Rate Amount

1 CARRIAGE OF MATERIAL

By Mechanical Transport including loading,unloading and

1.1.2 Carriage of earth

Earth work in excavation by mechanical means (Hydraulic

excavator)/ manual means over areas (exceeding 30 cm in

depth, 1.5 m in width as well as 10 sqm on plan) including

getting out and disposal of excavated earth lead upto 50 m and

for all lift, as directed by Engineer-in-charge.

Earth work in excavation by mechanical means (Hydraulic

excavator) / manual means in foundation trenches or drains (not

exceeding 1.5 m in width or 10 sqm on plan), including dressing

2.8 of sides and ramming of bottoms, lift upto 1.5 m, including ₹ 0.00

getting out the excavated soil and disposal of surplus excavated

soil as directed, within a lead of 50 m.

Filling available excavated earth (excluding rock) in trenches,

plinth, sides of foundations etc. in layers not exceeding 20cm in

2.25 depth, consolidating each deposited layer by ramming and Cum 982.91 196.00 ₹ 1,92,650.75

watering, lead up to 50 m and lift upto 1.5 m.

Excavating, supplying, stacking and filling of local earth

(including royalty) by mechanical transport upto a lead of 5km

also including ramming and watering of the earth in layers not

exceeding 20 cm in foundation trenches, plinth, sides of

foundation etc. complete for all lift.

Supplying and filling in plinth with sand under floors, including

2.27 watering, ramming, consolidating and dressing complete. Cum 10.00 2123.75 ₹ 21,237.50

CONCRETE WORK: ₹ 0.00

Providing and laying in position cement concrete of specified

4.1 grade excluding the cost of centering and shuttering - All work ₹ 0.00

up to plinth level

1:4:8 (1 Cement : 4 coarse sand (zone-lll) derived from natural

4.1.8 sources : 8 graded stone aggregate 40 mm nominal size cum 181.57 6812.00 ₹ 12,36,882.09

derived from natural sources)

Centering and shuttering including strutting, propping etc. and

removal of form for all heights :

4.3.1 Foundations, footings, bases of columns sqm 344.08 392.15 ₹ 1,34,930.97

Making plinth protection 50mm thick of cement concrete 1:3:6 (1

cement : 3 coarse sand : 6 graded stone aggregate 20 mm

nominal size) over 75mm thick bed of dry brick ballast 40 mm

4.17 nominal size, well rammed and consolidated and grouted with Sqm 165.60 749.30 ₹ 1,24,084.08

fine sand, including necessary excavation, levelling & dressing

& finishing the top smooth.

RCC WORK ₹ 0.00

Centering and shuttering including strutting, propping etc. and

removal of form for all heights :

Foundations, footings, bases of columns etc. for mass concrete.

Suspended floors, roofs, landings, balconies and access

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Lintels, beams, plinth beams, girders, bressumers and

5.9.6 Columns, Pillars, Piers, Abutments, posts and Struts Sqm 2618.06 961.30 ₹ 25,16,739.54

5.9.7 Stairs, (excluding landings) except spiral-staircases. Sqm 12.10 764.95 ₹ 9,255.90

Reinforcement for R.C.C. work including straightening, cutting,

5.22 bending, placing in position and binding all complete upto plinth ₹ 0.00

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening,

5.22 A cutting, bending, placing in position and binding all complete ₹ 0.00

above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500 D or more.

Providing and laying in position ready mixed or site batched

design mix cement concrete for reinforced cement concrete

work; using coarse aggregate and fine aggregate derived from

natural sources, Portland Pozzolana / Ordinary Portland

/Portland Slag cement, admixtures in recommended proportions

as per IS: 9103 to accelerate / retard setting of concrete, to

improve durability and workability without impairing strength;

including pumping of concrete to site of laying, curing, carriage

for all leads; but excluding the cost of centering, shuttering,

finishing and reinforcement as per direction of the engineer-in-

5.33 charge, for the following grades of concrete.: Note: Extra ₹ 0.00

cement up to 10% of the minimum specified cement content

in design mix shall be payable separately. In case the cement

content in design mix is more than 110% of the specified

minimum cement content, the contractor shall have discretion to

either re-design the mix or bear the cost of extra cement.

5.33.1 All works upto plinth level ₹ 0.00

Concrete of M25 grade with minimum cement content of 330 kg

Concrete of M30 grade with minimum cement content of 350 kg

5.33.2 All works above plinth level upto floor V level ₹ 0.00

Concrete of M25 grade with minimum cement content of 330 kg

Add for using extra cement in the items of design mix over and

above the specified cement content therein.

BRICK WORK ₹ 0.00

Brick work with common burnt clay F.P.S. (non modular) bricks

6.1 of class designation 7.5 in foundation and plinth in: ₹ 0.00

6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 122.38 7132.25 ₹ 8,72,833.34

Brick work with common burnt clay F.P.S. (non modular) bricks

6.4 designation 7.5 in superstructure above plinth level up to floor V ₹ 0.00

all shapes and sizes in:

6.4.2 Cement mortar 1:6 (1 cement: 6 coarse sand) cum 520.72 9105.95 ₹ 47,41,692.17

Half brick masonry with common burnt clay F.P.S. (non

modular) bricks

6.13 of class designation 7.5 in superstructure above plinth level up ₹ 0.00

6.13.1 Cement mortar 1:3 (1 cement :3 coarse sand) sqm 825.24 1150.50 ₹ 9,49,438.62

Extra for providing and placing in position 2 Nos 6mm dia. M.S.

6.15 bars at every third course of half brick masonry. sqm 825.24 104.80 ₹ 86,485.15

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Brick edging 7cm wide 11.4 cm deep to plinth protection with

common burnt clay F.P.S. (non modular) bricks of class

6.44 designation 7.5 including grouting with cement mortar 1:4 (1 Mtr 184.00 59.45 ₹ 10,938.80

cement : 4 fine sand).

WOOD WORK: ₹ 0.00

Providing wood work in frames of doors, windows, clerestory

windows and other frames, wrought framed and fixed in position

9.1 with hold fast lugs or with dash fasteners of required dia & ₹ 0.00

length (hold fast lugs or dash fastener shall be paid for

9.1.1 Second class teak wood cum 3.30 142949.70 ₹ 4,71,734.01

Providing and fixing ISI marked flush door shutters conforming

to IS :2202 (Part |) decorative type, core of block board

construction with frame of 1st class hard wood and well

9.2 matched teak 3 ply veneering with vertical grains or cross bands ₹ 0.00

and face veneers on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges

with necessary screws

Extra for Providing and fixing flush doors with decorative

veneering instead of non decorative ISI marked flush door

shutters conforming to IS: 2202 (Part I)

Extra for providing lipping with 2nd class teak wood battens 25

mm minimum depth on all edges of flush door shutters (over all

area of door shutter to be measured).

Extra for cutting rebate in flush door shutters (Total area of the

shutter to be measured).

Providing and fixing wooden moulded beading to door and

9.4 window frames with iron screws ,plugs and priming coat ₹ 0.00

unexposed surface etc.complete.

9.40.1 2nd class teak wood

Providing and fixing factory made laminated veneer lumber

glazed shutter conforming to IS: 14616 and TADS 15:2001 (Part

B), using 4 mm thick float glass panes for doors, windows and

clerestory windows, fixing with butt hinges of required size with

necessary screws, all as per directions of Engineer-in-charge ₹ 0.00

(Note:- Butt hinges and necessary screws shall be paid

Extra for providing ISI marked Stainless Steel butt hinges

instead of M.S. pressed butt hinges bright finished of required

size with necessary screws. (Shutter area to be measured).

Providing and fixing M.S. grills of required pattern in frames of

windows etc. with M.S. flats, square or round bars etc. including

priming coat with

approved steel primer all complete.

Fixed to openings /wooden frames with rawl plugs screws

Providing and fixing ISI marked, IS : 1341, M.S. heavy weight

finished butt hinges with necessary screws etc. complete :

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Providing 40x5 mm flat iron hold fast 40 cm long including fixing

to frame with 10 mm diameter bolts, nuts and wooden plugs and

embedding in cement concrete block 30x10x15cm 1:3:6 mix (1

cement : 3 coarse sand : 6 graded stone aggregate 20mm

Providing and fixing ISI marked oxidised M.S. sliding door bolts

9.62 with nuts and screws etc. complete (Copper oxidised as per IS ₹ 0.00

Providing and fixing bright finished brass tower bolts (barrel

type) with necessary screws etc. complete :

Providing and fixing bright finished brass 100 mm mortice latch

and lock with 6 levers and a pair of lever handles of approved

quality with necessary screws etc. complete.

Providing and fixing bright finished brass handles with screws

Providing and fixing bright finished brass hanging type floor

9.82 door stopper with necessary screws, etc. complete. Each 40.00 121.65 ₹ 4,866.00

Providing and fixing aluminium extruded section body tubular

type universal hydraulic door closer (having brand logo with ISI,

IS: 3564, embossed on the body, door weight upto 36 Kg. to 80

Kg. and door width from 701 mm to 1000 mm), with double

speed adjustment with necessary accessories and screws etc.

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door

Frames of cross-section 90 mm x 45 mm having single rebate

of 32 mm x 15 mm to receive shutter of 30 mm thickness. The

laminate shall be moulded with fire resistant grade unsaturated

polyester resin and chopped mat. Door frame laminate shall be

2 mm thick and shall be filled with suitable wooden block in all metre 34.80 570.95 ₹ 19,869.06

the three legs. The frame shall be covered with fiber glass from

all sides. M.S. stay shall be provided at the bottom to steady the

9.122 Providing and fixing to existing door frames. ₹ 0.00

30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door

shutter in different plain and wood finish made with fire

retardant grade unsaturated polyester resin, moulded to 3 mm

thick FRP laminate all around, with suitable wooden blocks

inside at required places for fixing of fittings and polyurethane

foam (PUF)/Polystyrene foam to be used as filler material

throughout the hollow panel, casted monolithically with testing

parameters of F.R.P. laminate conforming to table - 3 of IS:

14856, complete as per direction of Engineer-in-charge.

Providing & Fixing decorative high pressure laminated sheet of

plain / wood grain in gloss / matt / suede finish with high density

protective surface layer and reverse side of adhesive bonding

quality conforming to IS : 2046 Type S, including cost of

adhesive of approved quality.

Providing and fixing panic bar / latch (Double point) fitted with a

single body, Trim Latch & Lock on back side of the Panic Latch

9.139 of reputed brand and manufacture to be approved by the each 2.00 8366.15 ₹ 16,732.30

Engineer- in- charge, all complete.

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Providing and fixing fire resistant door frame of section 50 x 60

mm on horizontal side & 35 x 60 mm on vertical sides having

built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating

not less than 120gm/ sqm) suitable for mounting 120 minutes

Fire Rated Glazed Door Shutters. The frame shall be filled with

mineral wool Insulation having density minimum 96Kg/cum. The

frame will have a provision of G.I. anchor FAstners 14 nos ( 5

each on vertical style & 4 on horizontal style of size M10 x 80 ) meter 13.20 2202.90 ₹ 29,078.28

suitable for fixing in the opening along with factory made

template for SS ball bearing hinges of Size 100x89x3mm for

fixing of fire rated glazed shutter . The frame shall be finished

with a approved fire resistant primer or powder coating of not

less than 30 micron in desired shade as per the directions of

Engineer - in- Charge . (Cost of SS ball bearing hinges is

Providing and fixing 60 mm thick glazed fire resistant door

shutters of 120 minutes fire rating confirming to IS:3614 (Part II)

or EN1634-1:1999, tested and certified as per laboratory

approved by Engineer-in-Charge, with suitable mounting on

door frame, consisting of vertical styles, top rail & side rail 60

mm x 60 mm wide and bottom rail of 110 mm x 60 mm made

out of 1.6mm thick G.I. sheet (zinc coating not less than

120gm/sqm) duly filled mineral wool insulation having density

minimum 96 kg/cum and fixing with necessary stainless steel

ball bearing hinges of size 100x89x3mm of approved make,

including applying a coat of approved fire resistant primer or

powder coating not less than 30 micron etc all complete as per

direction of Engineer-in-Charge (panelling to be paid for

Providing and fixing glazing in fire resistant door shutters, fixed

panels & partitions etc., with G.I. beading made out of 1.6 mm

thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20

x 33 mm screwed with M4 x 38 mm SS screws at distance 75

mm from the edges and 150 mm c/c , including applying a coat

of approved fire resistant primer/ powder coating of not less

than 30 micron on G.I. beading, & special

ceramic tape of 5 x 20 mm size etc complete in all respect as

2016, IS 16231 (Part 3):2016 and as per direction of Engineer-

with glass of required thickness having 120 minutes of fire

both integrity & radiation control (EW120) and minimum 20

insulation (EI20). The manufacturer have to give test

report/certification

of fire glass and the glass should have the stamp showing the

E, EW & EI. The glass shall be tested in approved NABL

or by any other accreditation body which operates in

accordance with

ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for

calibration scopes shall be eligible. The maximum glazing size

not be more than 1100x2200 mm (w x h) or 2.42 sqm.

FINISHING: ₹ 0.00

13.1 12 mm cement plaster of mix : ₹ 0.00

18 mm cement plaster in two coats under layer 12 mm thick

cement plaster 1:5 (1 cement : 5 coarse sand) finished with a

top layer 6 mm thick cement

plaster 1:6 (1 cement : 6 fine sand).

13.16 6 mm cement plaster of mix : ₹ 0.00

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Wall painting with acrylic emulsion paint of approved brand and

manufacture to give an even shade :

13.82.1 Two or more coats on new work Sqm 4092.07 137.45 ₹ 5,62,454.75

Providing and applying white cement based putty of average

thickness 1 mm, of approved brand and manufacturer, over the

plastered wall surface to prepare the surface even and smooth

Wall painting with premium acrylic emulsion paint of interior

grade, having VOC (Volatile Organic Compound ) content less

than 50 grams/ litre of approved brand and manufacture,

including applying additional coats wherever required to achieve

even shade and colour.

Flooring ₹ 0.00

25 mm wooden planking, tongued and grooved in flooring,

11.33 including fixing with iron screws complete with : ₹ 0.00

11.33.1 Second class teak wood sqm 274.39 4508.95 ₹ 12,37,225.56

Providing and fixing 10 mm thick acid and/or alkali resistant tiles

of approved make and colour using acid and/or alkali resisting

mortar bedding, and joints filled with acid and/or alkali resisting

cement as per IS : 4457, complete as per the direction of

Engineer-in- Charge.

In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof

11.21.1 cement : 4 coarse sand) 11.21.1.1 Acid and alkali resistant tile sqm 733.81 1738.15 ₹ 12,75,471.50

In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof cement

11.21.2 : 4 coarse sand) 11.21.2.1 Acid and alkali resistant tile sqm 254.21 1884.90 ₹ 4,79,151.00

VITRIFIED FLOOR TILES ₹ 0.00

Providing and laying vitrified floor tiles in different sizes

(thickness to be specified by the manufacturer) with water

absorption less than 0.08% and conforming to IS: 15622, of

approved make, in all colours and shades, laid on 20 mm thick

cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey ₹ 0.00

cement slurry @ 3.3 kg/ sqm including grouting the joints with

white cement and matching pigments etc., complete.

Providing and laying Vitrified tiles in different sizes (thickness to

be specified by manufacturer), with water absorption less than

0.08 % and conforming to I.S. 15622, of approved make, in all

colours & shade, in skirting, riser of steps, over 12 mm thick bed

11.46 of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with ₹ 0.00

grey cement slurry @ 3.3 kg/ sqm including grouting the joint

with white cement & matching pigments etc. complete.

Providing and laying Polished Granite stone flooring in required

design and patterns, in linear as well as curvilinear portions of

the building all complete as per the architectural drawings with

18 mm thick stone slab over 20 mm (average) thick base of

cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed

with cement slurry and pointing with white cement slurry ₹ 0.00

admixed with pigment of matching shade including rubbing ,

curing and polishing etc. all complete as specified and as

directed by the Engineer-in-Charge.

Polished Granite stone slab of colour Black, Cherry/Ruby Red

Cladding ₹ 0.00

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Providing and fixing dry cladding upto 10 metre height with 30

mm thick gang saw cut stone with machine cut edges of uniform

colour and size

upto 1mx1m, fixed to structural steel frame work and/ or with the

8.20 help of cramps, pins etc. and sealing the joints with approved ₹ 0.00

weather sealant as per Architectural drawing and direction of

Engineer-in-charge. (The steel frame work, stainless steel

cramps and pins etc. shall be paid for separately).

8.20.1 Red sand stone - 30 mm thick gang saw cut stone sqm 165.60 2902.65 ₹ 4,80,678.84

Providing and fixing structural steel frame (for dry cladding with

30 mm thick gang saw cut with machine cut edges sand stone)

on walls at all

heights using M.S. square/ rectangular tube in the required

pattern as per architectural drawing, including cost of cutting,

bending, welding etc. The

frame work shall be fixed to the wall with the help of M.S.

brackets/ lugs of angle iron/ flats etc. which shall be welded to

the frame and embedded in

brick wall with cement concrete block 1:2:4 (1 cement :2 coarse

sand :4 graded stone aggregate 20 mm nominal size) of size

including cost of necessary centring and shuttering and with

approved expansion hold fasteners on CC/RCC surface,

including drilling necessary holes. Approved cramps/ pins etc.

shall be welded to the frame work to support stone cladding, the

steel work will be given a priming coat of Zinc primer as

approved by Engineer-in-charge and painted with two or more

coats of epoxy paint (Shop drawings shall be submitted by the

contractor to the Engineer-in-charge for approval before

execution). The frame work shall be fixed in true horizontal &

vertical lines/planes. (Only structural steel

frame work shall be measured for the purpose of payment,

stainless steel

cramps shall be paid for separately and nothing extra shall be

Providing and fixing adjustable stainless steel cramps of

approved quality, required shape and size, adjustable with

stainless steel nuts, bolts and washer (total weight not less than

260 gram), for dry stone cladding fixed on frame work at

suitable location, including making necessary recesses in stone each 1104.00 437.00 ₹ 4,82,448.00

slab, drilling required holes etc complete as per direction of the

Engineer-in-charge.

Providing and fixing copper pins 7.5 cm long 6 mm diameter for

securing adjacent stones in stone wall lining in cement mortar

1:2 (1 cement : 2 coarse sand), including making the necessary

Railing ₹ 0.00

Providing and fixing stainless steel ( Grade 304) railing made of

Hollow tubes, channels, plates etc., including welding, grinding,

buffing, polishing and making curvature (wherever required) and

fitting the same with necessary stainless steel nuts and bolts

complete, i/c fixing the railing with necessary accessories &

stainless steel dash fasteners , stainless steel bolts etc., of

10.28 required size, on the top of the floor or the side of waist slab kg 124.20 772.40 ₹ 95,932.08

with suitable arrangement as per approval of Engineer-

incharge, (for payment purpose only weight of stainless steel

members shall be considered excluding fixing accessories such

as nuts, bolts, fasteners etc.).

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Providing and fixing 18 mm thick gang saw cut, mirror polished,

premoulded and prepolished, machine cut for kitchen platforms,

vanity counters, window sills, facias and similar locations of

required size, approved shade, colour and texture laid over 20

mm thick base cement mortar 1:4 (1 cement : 4 coarse sand),

joints treated with white cement, mixed with matching pigment,

epoxy touch ups, including rubbing, curing, moulding and

polishing to edges to give high gloss finish etc. complete at all

8.2.2 Granite of any colour and shade ₹ 0.00

Providing and fixing chromium plated brass 100 mm mortice

latch and lock with 6 levers and a pair of lever handles of

approved quality with necessary screws etc. complete.

Ceiling ₹ 0.00

Providing and fixing tiled false ceiling of specified materials of

size 595x595 mm in true horizontal level, suspended on inter

locking metal grid of hot dipped galvanized steel sections (

galvanized @ 120 grams/ sqm, both side inclusive) consisting of

main "T" runner with suitably spaced joints to get required

length and of size 24x38 mm made from 0.30 mm thick

(minimum) sheet, spaced at 1200 mm center to center and

cross "T" of size 24x25 mm made of 0.30 mm thick (minimum)

sheet, 1200 mm long spaced between main "T" at 600 mm

center to center to form a grid of 1200x600 mm and secondary

cross "T" of length 600 mm and size 24x25 mm made of 0.30

12.52 mm thick (minimum) sheet to be interlocked at middle of the ₹ 0.00

1200x600 mm panel to form grids of 600x600 mm and wall

angle of size 24x24x0.3 mm and laying false ceiling tiles of

approved texture in the grid including, required cutting/making,

opening for services like diffusers, grills, light fittings, fixtures,

smoke detectors etc. Main "T" runners to be suspended from

ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed

to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4

mm GI adjustable rods with galvanised butterfly level clips of

size 85 x 30 x 0.8 mm spaced at 1200 mm center to center

along main T, bottom exposed width of 24 mm of all T-sections

shall be pre-painted with polyester paint, all complete for all

GI Metal Ceiling Lay in perforated Tegular edge global white

color tiles of size 595x595 mm and 0.5 mm thick with 8 mm

drop; made of GI sheet having galvanizing of 100 gms/sqm

(both sides inclusive) and 20% perforation area with 1.8 mm dia

holes and having NRC (Noise Reduction Coefficient ) of 0.5,

electro statically polyester powder coated of thickness 60 Sqm 82.00 2068.75 ₹ 1,69,637.50

microns (minimum), including factory painted after bending and

perforation and backed with a black Glass fiber acoustical

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Providing and Fixing 15 mm thick densified tegular edged eco

friendly light weight calcium silicate false ceiling tiles of

approved texture of size 595 x 595 mm in true horizontal level,

suspended on inter locking metal grid of hot dipped galvanised

steel sections (galvanising @ 120 grams per sqm including both

side) consisting of main ‘T’ runner suitably spaced at joints to

get required length and of size 24x38 mm made from 0.33 mm

thick (minimum) sheet, spaced 1200 mm centre to centre, and

cross “T” of size 24x28 mm made out of 0.33 mm (Minimum)

sheet, 1200 mm long spaced between main’T’ at 600 mm

centre to centre to form a grid of 1200x600 mm and secondary

cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33

mm thick (Minimum) sheet to be inter locked at middle of the

1200x 600 mm panel to from grid of size 600x600 mm, resting

on periphery walls /partitions on a Perimeter wall angle pre-

coated steel of size(24x24X3000 mm made of 0.40 mm thick

(minimum) sheet with the help of rawl plugs at 450 mm centre to

centre with 25 mm long dry wall screws @ 230 mm interval and

laying 15 mm thick densified edges calicum silicate ceiling tiles

of approved texture in the grid, including, cutting/ making

opening for services like diffusers, grills, light fittings, fixtures,

smoke detectors etc., wherever required. Main ‘T’ runners to be

suspended from ceiling using G.I. slotted cleats of size

25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long

dash fasteners, 4 mm G.I. adjustable rods with galvanised steel

level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre

to centre along main ‘T’. Bottom exposed with 24 mm of all T-

sections shall be pre-painted with polyster baked paint, for all

heights, as per specifications, drawings and as directed by

Engineer-in-Charge. Note :- Only calcium silicate false ceiling

Roofing ₹ 0.00

Steel work in built up tubular (round, square or rectangular

hollow tubes etc.) trusses etc., including cutting, hoisting, fixing

in position and applying

a priming coat of approved steel primer, including welding and

bolted with special shaped washers etc. complete.

10.16.1 Hot finished welded type tubes kg 121795.38 194.40 ₹ 2,36,77,021.87

Providing and fixing precoated galvanised iron profile sheets

(size, shape and pitch of corrugation as approved by Engineer-

in-Charge) of total

coated thickness 0.50 mm (base metal of minimum 0.45 mm

thickness with total coating thickness of 0.05mm) with zinc

coating 120 grams per

sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy

primer on both side of the sheet and polyester top coat 15-18

12.50 microns. Sheet should sqm 4059.85 738.65 ₹ 29,98,805.25

have protective guard film of 25 microns minimum to avoid

scratches during transportation and should be supplied in single

length upto 12 metre or as desired by Engineer-in-charge. The

sheet shall be fixed using self drilling /self tapping screws of

size (5.5x 55 mm) with EPDM seal, complete upto any pitch in

horizontal/ vertical or curved surfaces, excluding the cost of

purlins, rafters and trusses and including cutting to size and

shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing

accessories of total coated thickness 0.50 mm (base metal of

minimum 0.45 mm thickness with total coating thickness of 0.05

mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240

mpa steel grade, 5-7 microns epoxy primer on both side of the ₹ 0.00

sheet and polyester top coat 15-18 microns using self drilling/

self tapping screws complete :

12.51.6 Gutter (600 mm over all girth) metre 180.00 1313.70 ₹ 2,36,466.00

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Providing fixing thermal insulation of ceiling (under deck

insulation) with Resin Bonded Fibre glass wool conforming to IS

: 8183, density 24kg / m3, 50 mm thick, wrapped in 200 G Virgin

12.34 Polythene bags, fixed to ceiling with metallic cleats (50x50x3 sqm 4059.00 703.05 ₹ 28,53,679.95

mm) @ 60 cm and wire mesh of 12.5 mm x 24 gauge wire

mesh, for top most ceiling of building

Painting with synthetic enamel paint of approved brand and

13.62 manufacture of required colour to give an even shade : ₹ 0.00

Two or more coats on new work over an under coat of suitable

13.62.1 shade with ordinary paint of approved brand and manufacture sqm 541.20 226.25 ₹ 1,22,446.50

Providing and laying integral cement based water proofing

treatment including preparation of surface as required for

treatment of roofs, balconies, terraces etc consisting of following

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of

cement admixed with water proofing compound conforming to

IS. 2645 and approved by Engineer-in-charge over the RCC

slab including adjoining walls upto 300 mm height including

cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/brick bats

25 mm to 115 mm size with 50% of cement mortar 1:5 (1

22.7 cement : 5 coarse sand) admixed with water proofing compound

conforming to IS : 2645 and approved by Engineer-in-charge

over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5

coarse sand) admixed with water proofing compound

conforming to IS : 2645 and approved by Engineer-in-charge to

required slope and treating similarly the

adjoining walls upto 300 mm height including rounding of

of walls and slabs.

c) After two days of proper curing applying a second coat of

cement slurry using 2.75 kg/ sqm of cement admixed with water

proofing compound conforming to IS : 2645 and approved by

Engineerin- charge.

(d) Finishing the surface with 20 mm thick jointless cement

mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water

proofing compound conforming to IS : 2645 and approved by

Engineerin- charge including laying glass fibre cloth of approved

quality in top layer of plaster and finally finishing the surface with

trowel with neat cement slurry and making pattern of 300x300

mm square 3 mm deep.

(e) The whole terrace so finished shall be flooded with water for

a minimum period of two weeks for curing and for final test. All

above operations to be done in order

With average thickness of 120mm and minimum thickness at

khurra as 65 mm.

Sub Total of Civil DSR Amount ₹ 10,71,18,169.27

NS items ₹ 0.00

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Supply and fixing openable frame glass door , single leaf or

double leaf as per approve drawing. The door shall consist of

required number of fitting like flap hinges,Track arm door

closer,Lever handle, Mortise lock , door stopper and door jamb

(Reference model no. OMH-33/NSK-980/OZ-2BB-FP-SL 5*3*3

of make ozone or equivalent) Providing Door profile 60x35

having Glass thickness 10mm,12mm toughened Glass Sqm 52.50 52082.00 ₹ 27,34,305.00

Aluminium - material Maximum panel width: 1200mm, subject to

access into building (Reference Model number-OZKL-D60-

101of make ozone or equivalent) Aluminium grade – 6063T6

Frame colour: Black

Supply and fixing Fixed Glaze profile 45x22mm having Glass

thickness 10mm,12mm as toughened Glass (Reference Model

no-K-LITE 45 45x22mm of make ozone or equivalent) inculding

NSC-2 Glass to glass joint treatment: I Joint L-Joint ,T-Joint (8mm on Sqm 1030.27 10326.00 ₹ 1,06,38,588.67

the front face) Aluminium grade – 6063T6 Frame colour: Black

Providing and fixing of Khatambund made out of A-class Budloo

wood including preparation of wooden framing and 12mm

plywood backing all complete. Frame and ply base to be paid

Providing and fixing frosted film for Glass door and partition as

per manufacturer's specifications all complete as per the

satisfaction of Enginner-in-charge.

Providing and fixing 12mm thick plywood over GI Frame work

for Khatumband ceiling/wall clading at all height including

providing and fixing of frame work made of special sections,

power pressed from M.S. sheets and galvanized with zinc

coating of 120 gms/sqm (both side inclusive) as per IS : 277

and consisting of angle cleats of size 25 mm wide x 1.6 mm

thick with flanges of 27 mm and 37mm, at 1200 mm centre to

centre, one flange fixed to the ceiling with dash fastener 12.5

mm dia x 50mm long with 6mm dia bolts, other flange of cleat

fixed to the angle hangers of 25x10x0.50 mm of required length

with nuts & bolts of required size and other end of angle hanger

fixed with intermediate G.I. channels 45x15x0.9 mm running at

the spacing of 1200 mm centre to centre, to which the ceiling

NSC-5 section 0.5 mm thick bottom wedge of 80 mm with tapered Sqmt 300.00 1470.00 ₹ 4,41,000.00

flanges of 26 mm each having lips of 10.5 mm, at 450 mm

centre to centre, shall be fixed in a direction perpendicular to

G.I. intermediate channel with connecting clips made out of 2.64

mm dia x 230 mm long G.I. wire at every junction, including

fixing perimeter channels 0.5 mm thick 27 mm high having

flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed

to wall/partition with the help of rawl plugs at 450 mm centre,

with 25mm long dry wall screws @ 230 mm interval, including

fixing of plywood board to ceiling section and perimeter channel

with the help of dry wall screws of size 3.5 x 25 mm at 230 mm

c/c, as per manufacturer's specification and also including the

cost of making openings for light fittings, grills, diffusers, cutouts

made with frame of perimeter channels suitably fixed, all

Providing and fixing 300x35mm thick eaves boarding fied with

NSC-6 all necessary rquired plates, cleats, bolts etc all complete. (1st mtr 250.00 1000.00 ₹ 2,50,000.00

Providing ridges/hips 600mm overall width with GS plain colour

NSC-7 coated sheets with necessary fittings. mtr 100.00 500.00 ₹ 50,000.00

Providing valleys of 600mm wide over all in plain colour coated

sheets with necessary fittings.

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Providing and fixing 12mm wood plain lining T&G incl. PVC

plugs with screws over 12mm thick plyboard frame work 2'-0"

NSC-9 c/c 50mm wide fixed with friction nails with wall/soffits/ceiling/ sqm 188.00 2500.00 ₹ 4,70,000.00

Sub Total of Civil NDSR Amount ₹ 1,58,16,943.67

DSR 2023 Road Work

SCHEDULE ITEMS: ₹ 0.00

Earth work in excavation by mechanical means (Hydraulic

excavator)/manual means over areas (exceeding 30 cm in

depth, 1.5 m in width as well as 10 sqm on plan) including

getting out and disposal of excavated earth lead upto 50 m and

lift upto 1.5 m, as directed by Engineer-in-charge.

Providing and laying in position cement concrete of specified

4.1 grade excluding the cost of centering and shuttering - All work ₹ 0.00

up to plinth level

1:4:8 (1 Cement : 4 coarse sand (zone-lll) derived from natural

4.1.8 sources : 8 graded stone aggregate 40 mm nominal size cum 3.75 6812.00 ₹ 25,545.00

derived from natural sources)

Centering and shuttering including strutting, propping etc. and

removal of form for:

Foundations, footings, bases of columns etc. for mass concrete.

Steel reinforcement for R.C.C. work including straightening,

5.22A cutting, bending, placing in position and binding all complete ₹ 0.00

above plinth level

Thermo-Mechanically Treated bars of grade Fe-500 D or more.

Preparation and consolidation of sub-grade with power road

roller of 8 to 12 tonne capacity after excavating earth to an

average of 22.5cm depth, dressing to camber and consolidating

16.1 with road roller including making good the undulations etc. and Sqm 2398.75 218.90 ₹ 5,25,086.38

re-rolling the sub-grade and disposal of surplus earth lead upto

16.3 Supplying and stacking at site. ₹ 0.00

16.3.1 90 mm to 45 mm size stone aggregate Cum 239.88 2098.40 ₹ 5,03,364.19

16.3.3 53 mm to 22.4 mm size stone aggregate Cum 179.91 1842.30 ₹ 3,31,448.19

Laying, spreading and compacting stone aggregate of specified

sizes to WBM specifications in uniform thickness, hand picking,

rolling with 3 wheeled road / vibratory roller 8-10 tonne capacity

in stages to proper grade and camber, applying and brooming

requisite type of screening / binding material to fill up interstices Cum 419.78 1046.95 ₹ 4,39,488.67

of coarse aggregate, watering and compacting to the required

Providing and fixing in position pre-moulded joint filler in per cm

expansion per cm joints. joints.

Providing and laying at or near ground level factory made kerb

stone of M-25 grade cement concrete in position to the required

line, level and curvature, jointed with cement mortar 1:3 (1

cement: 3 coarse sand), including making joints with or without

grooves (thickness of joints except at sharp curve shall not to

16.69 more than 5mm), including making drainage opening wherever cum 51.30 10117.60 ₹ 5,19,032.88

required complete etc. as per direction of Engineer-in-charge

(length of finished kerb edging shall be measured for payment).

(Precast C.C. kerb stone shall be approved by Engineer-in-

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Providing and laying 60 mm thick faciory made cement concrete

interlocking paver block of M -30 grade made by block making

machine with strong vibratory compaction, of approved size,

design & shape, laid in required colour and pattern over and

including 50 mm thick compacted bed of coarse sand, filling the sqm 287.50 972.00 ₹ 2,79,450.00

joints with line sand etc. all complete as per the direction of

Engineer-in-charge.

Providing and applying 2.5 mm thick road marking strips

(retroreflective) of specified shade/ colour using hot

thermoplastic material by fully/ semi automatic thermoplastic

paint applicator machine fitted with profile shoe, glass beads

dispenser, propane tank heater and profile shoe heater, driven

16.62 by experienced operator on road surface including cost of sqm 35.00 747.80 ₹ 26,173.00

material, labour, T&P, cleaning the road surface of all dirt, seals,

oil, grease and foreign material etc. complete as per direction of

Engineer-in-charge and accordance with applicable

specifications.

Providing and laying design mix cement concrete of M-30

grade, in roads/ taxi tracks/ runways, using cement content as

per design mix, using coarse sand and graded stone aggregate

of 40 mm nominal size in appropriate proportions as per

approved & specified design criteria, providing dowel bars with

sleeve/ tie bars wherever required, laying at site, spreading and

compacting mechanically by using needle and surface vibrators,

levelling to required slope/ camber, finishing with required

texture, including steel form work with sturdy M.S. channel Cum 539.72 11098.45 ₹ 59,90,055.43

sections, curing, making provision for contraction/ expansion,

construction & longitudinal joints (10 mm wide x 50 mm deep)

by groove cutting machine, providing and filling joints with

approved joint filler and sealants, complete all as per direction

of Engineer-in-charge (Item of joint fillers, sealants, dowel bars

with sleeve/ tie bars to be paid separately).

Note:- Cement content considered in M-30 is @ 340 kg/cum.

Excess/ less cement used as per design mix is payable/

recoverable separately. Cement concrete manufactured in ₹ 0.00

automatic batching plant (RMC plant) i/c transportation to site in

Sub Total of Road DSR Amount ₹ 1,08,33,078.48

DSR 2025 Horticulture

Providing & laying of Selection no. 1 Doob grass turf with earth

50mm to 60mm thickness of existing ground prepared with

proper level and ramming with required tools wooden and than

rolling the surface with light roller make the surface smoothen

and light watering the same and maintenance for 30 days or sqm 1000.00 113.70 ₹ 1,13,700.00

more till the grass establish properly, as per direction of the

officer-in-charge

Supplying and stacking of good earth at site including royalty

and carriage upto 5 km lead complete (earth measured in

2.2 stacks will be reduced by 20% for payment). cum 184.00 803.75 ₹ 1,47,890.00

Supplying and stacking of sludge at site including royalty and

carriage upto 5 km lead complete (sludge measured in stacks

will be reduced by 8% for payment)

Supplying and stacking at site dump manure from approved

source, including carriage upto 5 km lead complete (manure

measured in stacks will be reduced by 8% for payment) :

2.4.1 Screened through sieve of I.S. designation 20 mm cum 100.00 391.35 ₹ 39,135.00

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Spreading of sludge, dump manure and/or good earth in

required thickness as per direction of officer-in-charge (cost of

sludge, dump manure and/ or good earth to be paid separately).

Random rubble masonry with hard stone in foundation and

plinth including levelling up with cement concrete 1:6:12 (1

cement : 6 coarse sand : 12 graded stone aggregate 20 mm

nominal size) upto plinth level with

7.1.1 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 90.00 7311.25 ₹ 6,58,012.50

Sub Total of Horticulture NDSR Amount ₹ 10,68,968.65

Providing and Fixing 16 Meter High Mast Flag pole including all

Accessories,Indian Flag,LED Aviation Light,MS Dome etc.

Complete in all Aspect excluding Civil Work For Foundation.

Sub Total of Horticulture NDSR Amount ₹ 4,19,352.40

DSR 2023 Boundary Wall

Earth Work ₹ 0.00

Earth work in excavation by mechanical means (Hydraulic

excavator/ manual means in foundation treanches or drains (not

exceeding 1.5m in width or 10 sqm on plan) including dressing

2.8 of sides and ramming of bottoms, lift upto 1.5m, including ₹ 0.00

getting out the excavated soil and disposal of surplus excavated

soil as directed within a lead of 50 mtr.

Filling available excavated earth (excluding rock) in trenches,

plinth, sides of foundations etc. in layers not exceeding 20cm in

2.25 depth, consolidating each deposited layer by ramming and cum 70.17 196.00 ₹ 13,752.78

watering lead upto 50 mtrs. and lift upto 1.5 mtr.

CONCRETE WORK ₹ 0.00

Providing and laying in position cement concrete of specified

4.1 grade excluding the cost of centring and shuttering - All work ₹ 0.00

upto plinth level:

1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40

mm nominal size)

RCC WORK ₹ 0.00

Centring and shuttering including strutting, propping etc. and

removal of form for:

Foundations, footings, bases of columns etc. for mass concrete.

Lintels, beams, plinth beams, girders, bressumers and

5.9.6 Columns, Pillars, Piers, Abutments, posts and Struts sqm 36.16 961.30 ₹ 34,760.61

Providing and laying in position ready mixed or site batched

design mix cement concrete for reinforced cement concrete

work; using coarse aggregate and fine aggregate derived from

natural sources, Portland Pozzolana / Ordinary Portland

/Portland Slag cement, admixtures in recommended proportions

as per IS: 9103 to accelerate / retard setting of concrete, to

improve durability and workability without impairing strength;

5.33 including pumping of concrete to site of laying, curing, carriage

for all leads; but excluding the cost of centering, shuttering,

finishing and reinforcement as per direction of the engineer-in-

charge, for the following grades of concrete.: Note: Extra

cement up to 10% of the minimum specified cement content

in design mix shall be payable separately. In case the cement

content in design mix is more than 110% of the specified

minimum cement content, the contractor shall have discretion to

either re-design the mix or bear the cost of extra cement.

5.33.1 All works upto plinth level ₹ 0.00

Concrete of M25 grade with minimum cement

content of 330 kg /cum

5.33.2.1 All works above plinth level upto floor five level Cum 9.11 9860.40 ₹ 89,808.52

add for using extra cement in the item for design mix over and

above the specified cement content

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Reinforcement for R.C.C. work including straightening, cutting,

5.22 bending, placing in position and binding all complete upto plinth ₹ 0.00

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening,

5.22 A cutting, bending, placing in position and binding all complete ₹ 0.00

above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500 D or more.

BRICK WORK: ₹ 0.00

Brick work with F.P.S. bricks of class designation 7.5 in

6.4 superstructure above plinth level up to floor V level in all shapes ₹ 0.00

6.4.2 Cement mortar 1:6 (1 cement: 6 coarse sand) Cum 30.43 9105.95 ₹ 2,77,084.95

STEEL WORK ₹ 0.00

Structural steel work in single section, fixed with or without

connecting plate, including cutting, hoisting, fixing in position

and applying a priming coat of approved steel primer all

Steel work welded in built up sections/ framed work, including

cutting, hoisting, fixing in position and applying a priming coat of

approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates

and similar works

FINISHING WORK ₹ 0.00

Finishing walls with Premium Acrylic Smooth exterior paint with

"Silicone additives of required shade

New work (two or more coats applied @1.43 ltr/10 sqm over

13.47.1 and including base coat of water proofing cement paint applied Sqm 264.60 171.10 ₹ 45,273.06

13.4 12 mm cement plaster of mix : ₹ 0.00

Providing and fixing concertina coil fencing with punched tape

concertina coil 600 mm dia 10 metre openable length ( total

length 90 m), having 50 nos rounds per 6 metre length, upto 3

m height of wall with existing angle iron ‘Y’ shaped placed 2.4m

or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed

wire, stud tied with G.I. staples and G.I. clips to retain horizontal,

16.53 including necessary bolts or G.I. barbed wire tied to angle iron, Metre 99.00 375.80 ₹ 37,204.20

all complete as per direction of Engineer-in-charge, with

reinforced barbed tape(R.B.T.) / Spring core (2.5 mm thick) wire

of high tensile strength of 165 kg/ sq. mm with tape (0.52 mm

thick) and weight 43.478 gm/ metre

(cost of M.S. angle, C.C. blocks shall be paid separately)

Painting with synthetic enamel paint of approved brand and

13.62 manufacture of required colour to give an even shade : sqm 29.04 226.25 ₹ 6,570.30

Sub Total of Boundary wall DSR Amount ₹ 15,08,241.28

EARTH WORK ₹ 0.00

1 CARRIAGE OF MATERIALS ₹ 0.00

By Mechanical Transport including loading,unloading and

Earth work in excavation by mechanical means (Hydraulic

excavator)/ manual means over areas (exceeding 30 cm in

depth, 1.5 m in width as well as 10 sqm on plan) including

getting out and disposal of excavated earth lead upto 50 m and

for all lift, as directed by Engineer-in-charge.

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Filling available excavated earth (excluding rock) in trenches,

plinth, sides of foundations etc. in layers not exceeding 20cm in

2.25 depth, consolidating cum 95.43 196.00 ₹ 18,704.28

each deposited layer by ramming and watering, lead up to 50

and for all lift.

Extra for every additional lift of 1.5 m or part thereof in

excavation / banking excavated or stacked materials.

Concrete Work ₹ 0.00

Providing and laying in position cement concrete of specified

4.1 grade excluding the cost of centering and shuttering - All work ₹ 0.00

up to plinth level

1:4:8 (1 Cement : 4 coarse sand (zone-lll) derived from natural

4.1.8 sources : 8 graded stone aggregate 40 mm nominal size cum 4.41 6812.00 ₹ 30,040.92

derived from natural sources)

RCC Work ₹ 0.00

Centering and shuttering including strutting, propping etc. and

removal of form for all heights :

Foundations, footings, bases of columns etc. for mass concrete.

Walls (any thickness) including attached pilasters, butteresses,

plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access

Lintels, beams, plinth beams, girders, bressumers and

5.9.6 Columns, Pillars, Piers, Abutments, posts and Struts sqm 15.88 961.30 ₹ 15,265.44

5.9.16 Edges of slabs and breaks in floors and walls. ₹ 0.00

Reinforcement for R.C.C. work including straightening, cutting,

5.22 bending, placing in position and binding all complete upto plinth ₹ 0.00

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening,

5.22 A cutting, bending, placing in position and binding all complete ₹ 0.00

above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500 D or more.

Providing and laying in position ready mixed or site batched

design mix cement concrete for reinforced cement concrete

work; using coarse aggregate and fine aggregate derived from

natural sources, Portland Pozzolana / Ordinary Portland

/Portland Slag cement, admixtures in recommended proportions

as per IS: 9103 to accelerate / retard setting of concrete, to

improve durability and workability without impairing strength;

including pumping of concrete to site of laying, curing, carriage

for all leads; but excluding the cost of centering, shuttering, ₹ 0.00

finishing and reinforcement as per direction of the engineer-in-

charge, for the following grades of concrete.: Note: Extra

cement up to 10% of the minimum specified cement content

in design mix shall be payable separately. In case the cement

content in design mix is more than 110% of the specified

minimum cement content,

the contractor shall have discretion to either re-design the mix

5.33.1 or bear

All works the costplinth

levelcement. ₹ 0.00

Concrete of M30 grade with minimum cement content of 350 kg

5.33.2 All works above plinth level upto floor V level ₹ 0.00

Concrete of M30 grade with minimum cement content of 350 kg

Brick Work ₹ 0.00

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Brick work with common burnt clay F.P.S. (non modular) bricks

6.4 designation 7.5 in superstructure above plinth level up to floor V ₹ 0.00

all shapes and sizes in:

6.4.2 Cement mortar 1:6 (1 cement: 6 coarse sand) Cum 23.60 9105.95 ₹ 2,14,900.42

Wood Work ₹ 0.00

Providing and fixing ISI marked oxidised M.S. tower bolt black

9.63 finish, (Barrel type) with necessary screws etc. complete ₹ 0.00

(Copper oxidised as per IS 1378)

Providing and fixing ISI marked oxidised M.S. door latches

9.65 conforming to IS:5930 with screws etc. complete (Copper ₹ 0.00

oxidised as per IS 1378)

Providing and fixing ISI marked oxidised M.S. handles

9.66 conforming to 1S:4992 with necessary screws etc. complete ₹ 0.00

(Copper oxidised as perIS 1378)

Providing and fixing bright finished brass hanging type floor

9.82 door stopper with necessary screws, etc. complete. Each 1.00 121.65 ₹ 121.65

Steel Work ₹ 0.00

Providing and fixing 1 mm thick M.S. sheet door with frame of

40x40x6 mm angle iron and 3 mm M.S. gusset plates at the

10.5 junctions and corners, all necessary fittings complete, including ₹ 0.00

applying a priming coat of approved steel primer.

10.5.1 Using M.S. angels 40x40x6 mm for diagonal braces sqm 2.40 5804.35 ₹ 13,930.44

Providing and fixing M.S. Tubular frames for doors, windows,

ventilators and cupboard with rectangular/ L-Type sections,

made of 1.60 mm thick M.S. Sheet, joints mitred, welded and

10.15 grinded finish, with profiles of required size, including fixing of ₹ 0.00

necessary butt hinges and screws and applying a priming coat

of approved steel primer.

Fixing with 15x3 mm lugs 10 cm long embedded in cement

concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse

sand : 6 graded stone aggregate 20 mm nominal size)

Providing & fixing fly proof wire gauze to windows, clerestory

doors with M.S. Flat 15x3 mm and nuts & bolts complete.

Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and

1.4 mm aperture on both sides

Flooring Work ₹ 0.00

62 mm thick cement concrete flooring with concrete hardener

topping, under layer 50 mm thick cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) and top layer 12 mm thick cement hardener

consisting of mix 1:2 (1 cement hardener mix: 2 graded stone

11.5 aggregate, 6 mm nominal size) by volume, hardening Sqm 30.00 1056.15 ₹ 31,684.50

compound mixed @ 2 litre per 50 kg of cement or as per

manufacture’s specifications. This includes cost of cement

slurry, but excluding the cost of nosing of steps etc. complete.

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Kota stone slab flooring over 20 mm (average) thick base laid

jointed with grey cement slurry mixed with pigment to match the

11.26 shade of ₹ 0.00

the slab, including rubbing and polishing complete with base of

mortar 1 : 4 (1 cement : 4 coarse sand) :

Kota stone slabs 20 mm thick in risers of steps, skirting, dado

laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3

sand) and jointed with grey cement slurry mixed with pigment to Sqm 2.25 2354.70 ₹ 5,298.08

the shade of the slabs, including rubbing and polishing

Finishing Work ₹ 0.00

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a

13.9 floating coat ₹ 0.00

of neat cement.

13.16 6 mm cement plaster of mix : ₹ 0.00

Wall painting with acrylic emulsion paint of approved brand and

manufacture to give an even shade :

13.82.1 Two or more coats on new work Sqm. 261.01 137.45 ₹ 35,875.82

Providing and fixing in position pre-cast R.C.C. manhole cover

19.19 and frame ₹ 0.00

of required shape and approved quality

19.19.3.1 Circular shape 560 mm internal diameter Each 3.00 1675.70 ₹ 5,027.10

Water Proofing Work ₹ 0.00

Providing and laying integral cement based treatment for water

proofing on horizontal surface at all depth below ground level

for under ground structures as directed by Engineer-in-Charge

and consisting of :

(i) Ist layer of 22 mm to 25 mm thick approved and specified

rough stone slab over a 25 mm thick base of cement mortar 1:3

(1 cement : 3 coarse sand) including applying of twice ( at base

and top of mortar ) cement slurry @ 2.2kg/m2 (each time) mixed

with water proofing compound conforming to IS:2645 in the

recommended proportion over the leveling

course (leveling course to be paid separately). Joints sealed

and grouted ₹ 0.00

with cement slurry mixed with water proofing compound.

(ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3

mixed with water proofing compound in recommended

(iii) Finishing top with stone aggregate of 10 mm to 12 mm

spreading @ 8 cudm/sqm thoroughly embedded in the 2nd

22.1.1 Using rough kota stone. sqm 103.91 1515.60 ₹ 1,57,486.00

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Providing and laying integral cement based treatment for water

proofing on the vertical surface by fixing specified stone slab 22

mm to 25 mm thick with cement slurry mixed with water proofing

compound conforming to IS:2645 in recommended proportions

with a gap of 20 mm (minimum) between stone slabs and the

receiving surfaces and filling the gaps with neat cement slurry

22.2 mixed with water proofing compound and finishing the exterior ₹ 0.00

of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand)

20 mm thick with neat cement punning mixed with water

proofing compound in recommended proportion complete at all

directed by Engineer-in-charge :

22.2.1 Using rough Kota stone sqm 65.16 2024.70 ₹ 1,31,929.45

Sub Total of UGT DSR Amount ₹ 22,44,069.76

DSR 2023 ESS Building

EARTH WORK ₹ 0.00

1 CARRIAGE OF MATERIAL ₹ 0.00

By Mechanical Transport including loading,unloading and

1.1.2 Carriage of earth ₹ 0.00

1.1.4 Carriage of excavated rock ₹ 0.00

Earth work in excavation by mechanical means (Hydraulic

excavator)/ manual means over areas (exceeding 30 cm in

depth, 1.5 m in width as well as 10 sqm on plan) including

getting out and disposal of excavated earth lead upto 50 m and

for all lift, as directed by Engineer-in-charge.

Earth work in excavation by mechanical means (Hydraulic

excavator) /manual means in foundation over areas (exceeding

30cm in depth , 1.5 m in width or 10 sqm on plan), including

2.7 disposal of excavated earth, for all leads and lifts, disposed ₹ 0.00

earth to be levelled and neatly dressed.

Earth work in excavation by mechanical means (Hydraulic

excavator) / manual means in foundation trenches or drains (not

exceeding 1.5 m in width or 10 sqm on plan), including dressing

2.8 of sides and ramming of bottoms, lift upto 1.5 m, including ₹ 0.00

getting out the excavated soil and disposal of surplus excavated

soil as directed, within a lead of 50 m.

Filling available excavated earth (excluding rock) in trenches,

plinth, sides of foundations etc. in layers not exceeding 20cm in

2.25 depth, consolidating each deposited layer by ramming and Cum 104.95 196.00 ₹ 20,570.20

watering, lead up to 50 m and lift upto 1.5 m.

Excavating, supplying, stacking and filling of local earth

(including royalty) by mechanical transport upto a lead of 5km

also including ramming and watering of the earth in layers not

exceeding 20 cm in foundation trenches, plinth, sides of

foundation etc. complete for all lift.

Supplying and filling in plinth with sand under floors, including

2.27 watering, ramming, consolidating and dressing complete. Cum 45.00 2123.75 ₹ 95,568.75

Supplying chemical emulsion in sealed containers including

delivery as specified.

Chlorpyriphos/Lindane Emulsifiable concentrate of 20%.

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Diluting and injecting chemical emulsion for POST-

CONSTRUCTIONAL anti-termite treatment:

Along the external wall below concrete or masonry apron using

chemical emulsion @ 2.25 litres per linear metre including

2.35.2 drilling and plugging holes etc.: With Chlorpyriphos/ Lindane metre 50.00 53.45 ₹ 2,672.50

E.C. 20% with 1% concentration

CONCRETE WORK: ₹ 0.00

Providing and laying in position cement concrete of specified

4.1 grade excluding the cost of centering and shuttering - All work ₹ 0.00

up to plinth level

1:4:8 (1 Cement : 4 coarse sand (zone-lll) derived from natural

4.1.8 sources : 8 graded stone aggregate 40 mm nominal size cum 24.36 6812.00 ₹ 1,65,940.32

derived from natural sources)

Centering and shuttering including strutting, propping etc. and

removal of form for all heights :

4.3.1 Foundations, footings, bases of columns sqm 25.90 392.15 ₹ 10,156.69

Making plinth protection 50mm thick of cement concrete 1:3:6 (1

cement : 3 coarse sand : 6 graded stone aggregate 20 mm

nominal size) over 75mm thick bed of dry brick ballast 40 mm

4.17 nominal size, well rammed and consolidated and grouted with Sqm 30.11 749.30 ₹ 22,561.42

fine sand, including necessary excavation, levelling & dressing

& finishing the top smooth.

RCC WORK ₹ 0.00

Reinforced cement concrete work in beams, suspended floors,

roofs having slope up to 15° landings, balconies, shelves,

chajjas, lintels, bands, plain window sills, staircases and spiral

stair cases above plinth level up to floor five level, including the

cost of centering, shuttering, finishing and excluding cum 6.44 11505.50 ₹ 74,095.42

reinforcement with 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded

stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and

removal of form for all heights :

Foundations, footings, bases of columns etc. for mass concrete.

Suspended floors, roofs, landings, balconies and access

Lintels, beams, plinth beams, girders, bressumers and

5.9.6 Columns, Pillars, Piers, Abutments, posts and Struts Sqm 162.60 961.30 ₹ 1,56,307.38

5.9.16 Edges of slabs and breaks in floors and walls. ₹ 0.00

5.9.19 Weather shade, chajjas, corbels etc. including edges. sqm 5.81 951.10 ₹ 5,525.89

Reinforcement for R.C.C. work including straightening, cutting,

5.22 bending, placing in position and binding all complete upto plinth ₹ 0.00

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening,

5.22 A cutting, bending, placing in position and binding all complete ₹ 0.00

above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500 D or more.

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Providing and laying in position ready mixed or site batched

design mix cement concrete for reinforced cement concrete

work; using coarse aggregate and fine aggregate derived from

natural sources, Portland Pozzolana / Ordinary Portland

/Portland Slag cement, admixtures in recommended proportions

as per IS: 9103 to accelerate / retard setting of concrete, to

improve durability and workability without impairing strength;

including pumping of concrete to site of laying, curing, carriage

for all leads; but excluding the cost of centering, shuttering,

5.33 finishing and reinforcement as per direction of the engineer-in-

charge, for the following grades of concrete.: Note: Extra

cement up to 10% of the minimum specified cement content in

design mix shall be payable separately. In case the cement

content in design mix is more than 110% of the specified

minimum cement content, the contractor shall have discretion

to either re-design the mix or bear the cost of extra cement.

5.33.1 All works upto plinth level ₹ 0.00

Concrete of M25 grade with minimum cement content of 330 kg

5.33.2 All works above plinth level upto floor V level ₹ 0.00

Concrete of M25 grade with minimum cement content of 330 kg

Add for plaster drip course/ groove in plastered surface or

moulding to R.C.C. projections.

BRICK WORK ₹ 0.00

Brick work with common burnt clay F.P.S. (non modular) bricks

6.1 of class designation 7.5 in foundation and plinth in: ₹ 0.00

6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 13.64 7132.25 ₹ 97,283.89

Brick work with common burnt clay F.P.S. (non modular) bricks

of class designation 7.5 in superstructure above plinth level up

to floor V level in all shapes and sizes in:

6.4.2 Cement mortar 1:6 (1 cement: 6 coarse sand) cum 56.01 9105.95 ₹ 5,10,024.26

Half brick masonry with common burnt clay F.P.S. (non

6.13 modular) bricks of class designation 7.5 in superstructure ₹ 0.00

above plinth level up to floor V level.

6.13.1 Cement mortar 1:3 (1 cement :3 coarse sand) sqm 33.24 1150.50 ₹ 38,242.62

Extra for providing and placing in position 2 Nos 6mm dia. M.S.

6.15 bars at every third course of half brick masonry. sqm 33.24 104.80 ₹ 3,483.55

Brick edging 7cm wide 11.4 cm deep to plinth protection with

common burnt clay F.P.S. (non modular) bricks of class

6.44 designation 7.5 including grouting with cement mortar 1:4 (1 Mtr 100.00 59.45 ₹ 5,945.00

cement : 4 fine sand).

MARBLE WORK: ₹ 0.00

Providing and fixing 18 mm thick gang saw cut, mirror polished,

premoulded and prepolished, machine cut for kitchen platforms,

vanity counters, window sills, facias and similar locations of

required size, approved shade, colour and texture laid over 20

mm thick base cement mortar 1:4 (1 cement : 4 coarse sand),

8.2 joints treated with white cement, mixed with matching pigment, ₹ 0.00

epoxy touch ups, including rubbing, curing,

moulding and polishing of edges to give high gloss finish etc.

complete at all levels.

8.2.2 Granite stone slab of colour black, Cherry/Ruby red ₹ 0.00

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Providing edge moulding to 18 mm thick marble stone counters,

Vanities etc., including machine polishing to edge to give high

8.3 gloss finish etc. complete as per design approved by Engineer- ₹ 0.00

WOOD WORK: ₹ 0.00

Providing wood work in frames of doors, windows, clerestory

windows and other frames, wrought framed and fixed in position

9.1 with hold fast lugs or with dash fasteners of required dia & ₹ 0.00

length (hold fast lugs or dash fastener shall be paid for

9.1.1 Second class teak wood cum 0.25 142949.70 ₹ 35,737.43

Providing and fixing ISI marked flush door shutters conforming

to IS :2202 (Part |) decorative type, core of block board

construction with frame of 1st class hard wood and well

matched teak 3 ply veneering with vertical grains or cross bands

and face veneers on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges

with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25

mm minimum depth on all edges of flush door shutters (over all

area of door shutter to be measured).

Providing and fixing wooden moulded beading to door and

9.4 window frames with iron screws ,plugs and priming coat ₹ 0.00

unexposed surface etc.complete.

9.40.1 2nd class teak wood ₹ 0.00

Providing 40x5 mm flat iron hold fast 40 cm long including fixing

to frame with 10 mm diameter bolts, nuts and wooden plugs and

embedding in cement concrete block 30x10x15cm 1:3:6 mix (1

cement : 3 coarse sand : 6 graded stone aggregate 20mm

Providing and fixing ISI marked oxidised M.S. sliding door bolts

9.62 with nuts and screws etc. complete (Copper oxidised as per IS ₹ 0.00

Providing and fixing bright finished brass tower bolts (barrel

type) with necessary screws etc. complete :

Providing and fixing bright finished brass 100 mm mortice latch

and lock with 6 levers and a pair of lever handles of approved

quality with necessary screws etc. complete.

Providing and fixing bright finished brass handles with screws

Providing and fixing bright finished brass hanging type floor

9.82 door stopper with necessary screws, etc. complete. Each 4.00 121.65 ₹ 486.60

Providing and fixing aluminium extruded section body tubular

type universal hydraulic door closer (having brand logo with ISI,

IS: 3564, embossed on the body, door weight upto 36 Kg. to 80

Kg. and door width from 701 mm to 1000 mm), with double

speed adjustment with necessary accessories and screws etc.

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Providing & Fixing decorative high pressure laminated sheet of

plain / wood grain in gloss / matt / suede finish with high density

protective surface layer and reverse side of adhesive bonding

quality conforming to IS : 2046 Type S, including cost of

adhesive of approved quality.

STEEL WORK ₹ 0.00

Structural steel work riveted, bolted or welded in built up

sections, trusses and framed work, including cutting, hoisting,

fixing in position and applying a priming coat of approved steel

primer all complete.

Supplying and fixing rolling shutters of approved make, made of

required size M.S. laths, interlocked together through their

entire length and jointed together at the end by end locks,

mounted on specially designed pipe shaft with brackets, side

guides and arrangements for inside and outside locking with

push and pull operation complete, including the cost of

providing and fixing necessary 27.5 cm long wire springs

manufactured from high tensile steel wire of adequate strength

conforming to IS: 4454 - part 1 and M.S. top cover of required

thickness for rolling shutters.

10.6.1 80x1.25 mm M.S. laths with 1.25 mm thick top cover sqm 9.00 3653.20 ₹ 32,878.80

10.7 Providing and fixing ball bearing for rolling shutters. each 4.00 492.35 ₹ 1,969.40

Extra for providing grilled rolling shutters manufactured out of 8

10.9 M.S. bar instead of laths as per design approved by Engineer-in- sqm 2.70 768.25 ₹ 2,074.28

(area of grill to be measured).

FLOORING ₹ 0.00

62 mm thick cement concrete flooring with concrete hardener

topping, under layer 50 mm thick cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) and top layer 12 mm thick cement hardener

consisting of mix 1:2 (1 cement hardener mix : 2 graded stone

aggregate, 6 mm nominal size) by volume, hardening

11.5 compound mixed @ 2 litre per 50 kg of cement or as per sqm 138.99 1056.15 ₹ 1,46,794.29

specifications. This includes cost of cement slurry, but excluding

of nosing of steps etc. complete.

Cement plaster skirting up to 30 cm height, with cement mortar

11.6 1:3 (1 cement : 3 coarse sand), finished with a floating coat of ₹ 0.00

Crazy marble stone flooring, including filling the gaps with light

shade pigment with white cement marble powder mixture (3

parts of white cement: 1 part of marble powder) by weight in

proportion of 4:7 (4 cement marble powder mix : 7 white, black

or white and black marble chips of sizes from 1 mm to 4 mm

11.15 nominal size by volume), with under layer 25 mm thick cement ₹ 0.00

concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate 12.5 mm nominal size), including rubbing, polishing

andcement slurry etc. complete :

18 mm thick crazy marble stone white, black or as specified

ROOFING ₹ 0.00

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement :

2 coarse sand : 4 stone aggregate 10mm and down gauge)

12.21 including finishing with cement mortar 1:3 (1 cement : 3 fine metre 52.50 305.15 ₹ 16,020.38

sand) as per standard design : In 75x75mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5

cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded

stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m

x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1

cement : 3 coarse sand) and a coat of neat cement, rounding each 3.00 298.25 ₹ 894.75

the edges and making and finishing the outlet complete.

FINISHING: ₹ 0.00

13.1 12 mm cement plaster of mix : ₹ 0.00

18 mm cement plaster in two coats under layer 12 mm thick

13.11 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm ₹ 0.00

plaster 1:6 (1 cement : 6 fine sand).

13.16 6 mm cement plaster of mix : ₹ 0.00

Distempering with 1st quality acrylic distemper (ready mixed)

having VOC content less than 50 gram/litre, of approved

manufacturer and of required shade and colour all complete to

achieve even shade and colour :

New work (two or more coats) over and including water

13.41.1 thinnable priming coat with cement primer having VOC content sqm 394.00 185.65 ₹ 73,146.10

less than 50 gram/litre

Finishing with Epoxy paint (two or more coats) at all locations

prepared and applied as per manufacturer’s specifications

13.52 including appropriate priming coat, preparation of surface, etc. ₹ 0.00

Wall painting with acrylic emulsion paint of approved brand and

manufacture to give an even shade :

13.82.1 Two or more coats on new work Sqm 312.42 137.45 ₹ 42,942.13

Providing and applying white cement based putty of average

thickness 1 mm, of approved brand and manufacturer, over the

plastered wall surface to prepare the surface even and smooth

ALUMINIUM WORK: ₹ 0.00

Providing and fixing aluminium work for doors, windows,

ventilators and partitions with extruded built up standard tubular

sections/ appropriate Z sections and other sections of approved

make conforming to IS: 733 and IS: 1285, fixing with dash

fasteners of required dia and size, including necessary filling up

the gaps at junctions, i.e. at top, bottom and sides with required

EPDM rubber/ neoprene gasket etc. Aluminium sections shall

21 be smooth, rust free, straight, mitred and jointed mechanically ₹ 0.00

wherever required including cleat angle, Aluminium snap

beading for glazing / panelling, C.P. brass / stainless steel

screws, all complete as per architectural drawings and the

directions of Engineer-in-charge. (Glazing, paneling and dash

fasteners to be paid for separately) :

21.1.1 For fixed portion ₹ 0.00

Anodised aluminium (anodised transparent or dyed to required

21.1.1.1 shade according to IS: 1868, Minimum anodic coating of grade kg 144.00 495.05 ₹ 71,287.20

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

For shutters of doors, windows & ventilators including providing

and fixing hinges/ pivots and making provision for fixing of

fittings wherever required including the cost of

EPDM rubber / neoprene gasket required (Fittings shall be paid

for separately)

Anodised aluminium (anodised transparent or dyed to required

21.1.2.1 shade according to IS: 1868, Minimum anodic coating of grade kg 43.20 598.60 ₹ 25,859.52

Providing and fixing glazing in aluminium door, window,

ventilator shutters and partitions etc. with EPDM rubber /

neoprene gasket etc. complete as per the architectural drawings

and the directions of engineer-in-charge . (Cost of aluminium

snap beading shall be paid in basic item):

With float glass panes of 5.5 mm thickness (weight not less

than 12.50 kg/ sqm)

Filling the gap in between aluminium frame & adjacent RCC/

Brick/ Stone work by providing weather silicon sealant over

21.8 backer rod of approved quality as per architectural drawings ₹ 0.00

and direction of Engineer-in-charge complete.

21.8.1 Upto 5 mm depth and 5 mm width metre 57.60 96.75 ₹ 5,572.80

Providing and fixing aluminium casement windows fastener of

21.15 required length for aluminium windows with necessary screws ₹ 0.00

21.15.1 Anodized (AC 15) aluminium each 12.00 89.40 ₹ 1,072.80

Sub Total of ESS Building DSR Amount ₹ 42,55,003.34

Supply and application of 2-component acrylic polymer modified

cementitious waterproofing coating over prepared

insulation/screed concrete laid to required slope on terrace, wet

areas and lift pit, comprising surface preparation,

crack/undulation treatment.

Sub Total of ESS Building NDSR Amount ₹ 1,64,429.61

NS Item Furniture

Reception table : The overall size of the reception table shall be

2400 mm length, 750 mm depth & 1050 mm height. On the front

side both ends shall be provided with groove design strips to

enhance the overall look. At the centre of the front side L shape

surface shall be provided fixed up with hinges to paste logo of

the University. The entire table shall be made up of 25mm /

18mm thick pre laminated particle board of E1 norms. Inside of

table a working height shelf should be provided or height 750

mm to keep desktop/ laptop and normal working with sitting. the

edges of the visible surface shall be sealed with 2mm thick PVC

NSF-01 lipping on automatic machine. Unless specified tolerance of +/- each 1.00 145360.00 ₹ 1,45,360.00

5mm to be considered for product dimensions Length, Depth &

height and tolerance of 5% to be considered in thickness & size

of material & components used. The OEM shall have ISO 9001,

BIFMA Level 2, Green Guard UL Gold Certification, AIOTA,

IGBC Gold rated factory certification and India Design Mark.

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

The overall size of Chair shall be height 1020 to 1120 +/-5 mm,

width should be 595 +/-5mm and depth should be 640 +/-5mm.

Back Width 435 mm at Top and 490mm at bottom, Seat Width

500 +/-5 mm, Seat Depth 465+/-5 mm and Seat height 450mm

to 550 mm +/-5mm range. Seat should be made up of foam pre

moulded at 55 kg/m3 density. hardness of 25+ 3kgf at 50%

deflection conforming to IS 3400. Seat shall be upholstered with

micro fabric 100% polyster 180 GSM abrasion > 50000 cycles.

No flamming or progressive smoldering within one hour of

placement of the cigarettes. Fire rated fabric confirming to BS

EN 1021 (match) should be used. The chair shall be supplied

with Mesh at the back rest. The back frame shall be made up of

injection molded nylon GF 3. Adjustable Lumbar Support of size

300 mm lenght, 150 mm height and 3mm thickness travel upto

65mm. The Chair should be provided with Snchyro mechanism

with single lever with one position lock. The mechanism shall

allow360 degree revolving feature along with height

adjustablility one Way with height adjustment button made of

Delrin P 500 & arm top shall be PU material. The mechansim

shall possess seat to back recline ratio of 3:7. The Gas Lift used

shall be class 4 tested as per ANSI BIFMA standards. Nylon

Base to be provied. Twin castors 50 mm dia with PA6 material

complying to ANSI/ BIFMA X 5.1 2017 standards. The base

shall be 660 mm PCD (26 inches) five pronged bases made up

of PA6, 30% glass filled reinforced with bottom ribbing for

additional buttress and strength. Tolerance of +/- 5mm to be

considered for product sizes i.e Length, Depth & height and

tolerance of 5% to be considered in pipe thickness & Pipe sizes.

The OEM shall have ISO 9001, BIFMA Level 2, Green Guard

UL Gold Certification, AIOTA, IGBC Gold rated factory

SIZE:2820Lx400Dx1805H

The horizontals and Verticals of the frame structure shall be

made from Aluminium extrusions of 6063 grade alumalloy,

confirming to DIN ISO -2768-1 and connected each other by

high pressure aluminum diecast connectors using counter sunk

screws to ensure stability, high strength & safety. Aluminium

profiles shall be used to fix the racks made up of 20x20Sq.mm

profile, sledge profile for 18.0mm thk shelf panel, sledge profile

for 5.0mm thk glass panel and sledge profile with two opposite

sides to fix 18.0mm thk panels on two sides parallelly. The

connectors used shall be 02-way, 03-way (2D), 03-way (3D), 04-

way & 05-way as required. All the connectors shall be pressure

diecast connectors in ADC-12 material confirming to ASTM E

composition and IS 1608 – 2005 for UTS & Ys. All connectors

shall be provided with M5 threads to fix M5x0.8P CSK screw.

The wooden planks used for shelves, back panels & planter box

shall be made up of 18mm thk prelam particle board on both

sides (PLT) with edge banding finish. Length & width / depth of

these planks shall be based on product size & design. Each

such shelf should be able to take weight upto 15.0Kgs UDL.

Height of Planter box shall be 120mm H, out of which about

19mm shall fit in the frame work. Visible height of planter box

shall be about 100 mm. Glass used shall be of 5mm thk clear

float glass. The leg height from ground shall be 75mm, each leg

shall be fitted with a leg bush injection moulded part in tough

engineering plastic material, ABS. Aluminium extrusions and

Diecast connectors shall be black matt powder coating finish

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

The overall size of the sofa shall be 2050 L x 790 D x 790 H.

Sofa inner frame structure shall be made mainly from the

combination of treated pine wood of 20-25mm thick & neem

based plywood sheets. The polyurethane (PU) foam of density

32 and 40 shall be used in seat constructions and 32 density

foam used in back construction along with the webbing belts.

Seat height should be 440mm (+/- 10mm) and seat depth shall

be 525mm (+/- 20mm). Each sofa individual set type shall

consist of 4 metal legs of 200 mm height that shall be laser cut

and press formed in 2mm thick CR steel in complaince with IS

513: 2008. The legs shall be formed in V-shape with 125 x

125mm length flanges on its top face and moulded leg bush

shall be fixed at its bottom that shall support height adjustment

of upto 10mm. To suppor thte sofa two nos wide flanges of the

leg shall be be provided. Legs shall be pretreated through nano

ceramic process that shall be environment friendly to enable

powder coating to the thickness of 50-80 microns. The fabric

used shall be 450-475 gms per meter having abrasion

resistance of more than 50K rubs high quality polyester fabric.

The OEM shall have ISO 9001, BIFMA Level 2, Green Guard

UL Gold Certification, AIOTA, IGBC Gold rated factory

certification and India Design Mark.

The overall size of the table shall be 1050 L x 525 D x 450 H

mm. The top surface of the table shall be in boat shape design

having maximum size at the middle & lesser at the ends to form

this unique shape. The table top shall be made up of 18mm

thick Prelaminated particle board of E1 norms. The edges shall

be sealed properly with 2mm thick PVC edge banding on

automatic machine. The understructure of the table shall be

made from solid wood i.e properly treated & seasoned kiln dried

beach wood, finished with clear synthetic PU coating for the

best resilence and high durability. The legs and the frame shall

be joined together by method of tenon and mortise for durability

and better aesthetics. Four legs shall be provided and the cross

NSF-05 section of leg at the bottom shall be 35x35 and top shall be each 3.00 16052.00 ₹ 48,156.00

55x35 provided in tappered finish for better looks. The outer

side of the legs shall be rounded & inner side shall be corner

edges. The wooden frame shall be of size 55mm x 22mm thick

with visible face of 55 mm front and 22mm shall be below the

table top running at all four ends as well as one support in the

middle. The OEM shall have ISO 9001, BIFMA Level 2, Green

Guard UL Gold Certification, AIOTA, IGBC Gold rated factory

certification and India Design Mark.

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

The overall size of the table shall be 600 L x 600 D x 450 H mm.

The top surface of the table shall be in boat shape design

having maximum size at the middle & lesser at the ends to form

this unique shape. The table top shall be made up of 18mm

thick Prelaminated particle board of E1 norms. The edges shall

be sealed properly with 2mm thick PVC edge banding on

automatic machine. The understructure of the table shall be

made from solid wood i.e properly treated & seasoned kiln dried

beach wood, finished with clear synthetic PU coating for the

best resilence and high durability. The legs and the frame shall

be joined together by method of tenon and mortise for durability

and better aesthetics. Four legs shall be provided and the cross

NSF-06 section of leg at the bottom shall be 35x35 and top shall be each 3.00 12672.00 ₹ 38,016.00

55x35 provided in tappered finish for better looks. The outer

side of the legs shall be rounded & inner side shall be corner

edges. The wooden frame shall be of size 55mm x 22mm thick

with visible face of 55 mm front and 22mm shall be below the

table top running at all four ends as well as one support in the

middle. The OEM shall have ISO 9001, BIFMA Level 2, Green

Guard UL Gold Certification, AIOTA, IGBC Gold rated factory

certification and India Design Mark.

Cabin Table in size of 2100W X 900D X 750H, Side unit of

1050W X 450D X 750H Table Top: 25mm thick Pre laminate

particle board E1 norms with 2mm PVC edge lipping on all

exposed edges. Two Long sides of the work surface shall be

provided with reverse tapered edge design created by

chamfering the board at 45 degree inside for 17mm length &

keeping 8mm straight & then edges sealed with 2mm thick PVC

Lipping on automatic machine. Leg: shall be made up of high

pressure aluminum die casted 20 degree tapered, number “7”

shape & oblong cross section of about 55mm on top, 45mm at

bottom and of 725mm length to get 750mm table height, it acts

as vertical structural support member, connected by a horizontal

cross beams 50x25x1.6thk (16g) ERW tube & connected to the

Aluminium diecast vertical legs through a high pressure

Aluminium diecast 90deg – 02 way connectors. The connector

should have “V” / “U” shape tapered groove for sliding a

Aluminium diecast slider nut. The slider nut shall be an

Aluminium diecast part that has same taper as of “V” / “U”

shape in the diecast connector. Modesty Panel: 18mm thk pre

lam board with 2mm PVC edge lipping of 450mm Ht. Wire

Management: 350mm Aluminium Flip Up and provision to

mount swicthes and sockets on PVC cable dump and Vertical

wire entry cover. Cross Beam: Leg to Leg shall be connected

using cross beams made from 50x25x1.60mm (16g)

Rectangular tube and to give floating look & to connect the table

top with cross beams injection moulded polycarbonate spacers

should be used of dia 61mm x 42.50mm H insert moulded with

M6x1P zinc blue plated bolt of 22mm L.Spacer height including

bolt should be 64.50mm. Side Composite Storage (Openable

Shutter +2D+1F) Top & Sides : 18mm Thk pre laminated

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Back Unit: Back Storage (Openable Shutter +2 Open

Compartments + 2 Half shutters + Single Open Compartment +

2 Openable Shutters) Top & Sides : 18mm Thk pre laminated

particle board Back E1 norms: 9mm Thk pre laminated particle

board Shutters : 18mm Thk pre laminated particle board

Handle. Handless Finger groove shall be created on top edge of

shutter doors by providing a reverse tapered profile edge of

6mm straight surface & 12 mm tapered towards inside at 45

degree & then sealed with minimum 2mm thick PVC lipping on

NSF-08 automatic machine. Suitable cam lock shall be provided. The each 4.00 92852.00 ₹ 3,71,408.00

overall unit shall be comes with powder coated metal legs. The

entire metal understructure shall be powder coated to 40-60

microns thickness. The OEM shall have ISO 9001, BIFMA Level

2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated

factory certification and India Design Mark.

The overall size of Chair shall be : Total height 1200 to 1300 +/-

5 mm, overall width 580mm , overall depth shall be 650mm,

Seat Width 480 +/-5 mm, Seat Depth 460+/-5 mm,Seat height

475-575 +/-5 mm, Back Width 425+/-5 mm at lumber support,

Back Width 480+/-5 mm at shoulder, Back height from seat 570

+/-5 mm. and the headrest size shall be 250WX150Hmm.

comes with 40mm of cushion thickness. Seat should be made

up of foam pre moulded at 55 kg/m3 density. hardness of 25+

3kgf at 50% deflection conforming to IS 3400. headrest shall be

upholstered with Leatherette 75% PVC & 25% polyester – 640

GSM, Abrasion-100000 cycles over PU faom. and the Seat shall

be upholstered with micro fabric 100% polyster 180 GSM

having abrasion > 50000 cycles fire rated fabric confirming to

BS EN 1021. Plywood used shall be 12mm thick 9 ply hot

pressed. The chair shall be supplied with high quality Mesh at

the back. The chair is provided with a Dynaflex dual-frame back

support system wherein the inner flexible back frame is

connected to the outer structural frame through a pivoted

coupling joint mechanism. The coupling joint dynamically

responds to the user’s body weight and posture movement,

enabling controlled flex and adaptive reclining support for

enhanced ergonomic comfort and spinal alignment. headrest

cushion made by 35mm thick foam at 55kg/m3 density.

Hardness of 25+3kgf at 50% deflection conforming to IS 3400.

The Chair should be provided with Synchro tilt Mechanism with

three Multi lock features. The mechanism shall allow 360

degree revolving feature along with height adjustablility. One

Way Adjustable Arms (Height) upto 9 step. Armrest shall be

provied with height adjustment button made of Delrin P 500.

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

The overall size of Chair shall be : Total height 1100 to 1200 +/-

5 mm, overall width 580mm , overall depth shall be 650mm,

Seat Width 480 +/-5 mm, Seat Depth 460+/-5 mm,Seat height

475-575 +/-5 mm, Back Width 425+/-5 mm at lumber support,

Back Width 480+/-5 mm at shoulder, Back height from seat 570

+/-5 mm. Seat should be made up of foam pre moulded at 55

kg/m3 density. hardness of 25+ 3kgf at 50% deflection

conforming to IS 3400. the Seat shall be upholstered with micro

fabric 100% polyster 180 GSM having abrasion > 50000 cycles

fire rated fabric confirming to BS EN 1021. Plywood used shall

be 12mm thick 9 ply hot pressed. The chair shall be supplied

with high quality Mesh at the back. The chair is provided with a

Dynaflex dual-frame back support system wherein the inner

flexible back frame is connected to the outer structural frame

through a pivoted coupling joint mechanism. The coupling joint

dynamically responds to the user’s body weight and posture

movement, enabling controlled flex and adaptive reclining

support for enhanced ergonomic comfort and spinal alignment.

The Chair should be provided with Synchro tilt Mechanism with

three Multi lock features. The mechanism shall allow 360

degree revolving feature along with height adjustablility. One

Way Adjustable Arms (Height) upto 9 step. Armrest shall be

provied with height adjustment button made of Delrin P 500.

The mechansim shall possess seat to back recline ratio of 3:7.

The Gas Lift used shall be class 4 tested as per ANSI BIFMA

standards. Nylon Base to be provied. Twin castors 60 mm dia

with PA6 material complying to ANSI/ BIFMA X 5.1 2017

standards. the axle pin shall be rust protected zinc passivated.

The base shall be 660 mm PCD (26 inches) five pronged bases

The overall size of workstation shall be 1200L x 600D x

750H.The worktop shall be made of 25mm thick pre laminate

partical boards with E1 norms dully finish with 2mm pvc edge

band all the side of worktop. Modesty shall be made of 18mm

thick pre laminate partical boards with E1 norms with 2mm pvc

edge band all the visible side and connected with 2 nos L-

shape pressure aluminium die casted connector. The height of

the modesty shall be 450mm. The understructure shall be made

up of MS powder coated legs having enhanced look trapezoidal

cross section size 52mm x 52mm x 52mm x 26mm with

chamfered corners and thickness of 1.6mm. Edges of the leg

should not have sharp edges. For safety of users a radius of

R3.20 mm should be provided. The Trapezoidal tube shall be

connected with die cast connectors at top, leg shoe & levelers at

bottom. High pressure aluminum die cast connectors shall of

ADC-12 material confirming to ASTM E 1251-2011, IS 7658-

1990 & IS 11035 – 1190. The vertical legs shall be connected

by horizontal beams with the help of aluminum die cast

connector that joints the legs vertically and horizontally with pipe

of cross section 50 x 25 mm x 1.6 mm thickness. The die cast

connect size shall be L shaped having angle of 10 degrees for

vertical leg side. The Diecast connector will have same shape

as of Trapezoidal vertical leg at one side and another side

matching to horizontal cross section 50x25. The spacers shall

be made of Polycarbonate (PC). For ease of wire management,

a 300 mm length & 142mm breadth flip up cover made up of

aluminum having soft closure should be provided. A flip down

mechanism enabled cable tray shall be provided below the

worktop to mount switches and sockets. Metal cable tray shall

be made of 0.8mm thick CRCA sheet with separator for data

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

The overall size of workstation shall be 1500L x 900D x

750H.The worktop shall be made of 25mm thick pre laminate

partical boards with E1 norms dully finish with 2mm pvc edge

band all the side of worktop. Modesty shall be made of 18mm

thick pre laminate partical boards with E1 norms with 2mm pvc

edge band all the visible side and connected with 2 nos L-

shape pressure aluminium die casted connector. The height of

the modesty shall be 450mm. The understructure shall be made

up of MS powder coated legs having enhanced look trapezoidal

cross section size 52mm x 52mm x 52mm x 26mm with

chamfered corners and thickness of 1.6mm. Edges of the leg

should not have sharp edges. For safety of users a radius of

R3.20 mm should be provided. The Trapezoidal tube shall be

connected with die cast connectors at top, leg shoe & levelers at

bottom. High pressure aluminum die cast connectors shall of

ADC-12 material confirming to ASTM E 1251-2011, IS 7658-

1990 & IS 11035 – 1190. The vertical legs shall be connected

by horizontal beams with the help of aluminum die cast

connector that joints the legs vertically and horizontally with pipe

of cross section 50 x 25 mm x 1.6 mm thickness. The die cast

connect size shall be L shaped having angle of 10 degrees for

vertical leg side. The Diecast connector will have same shape

as of Trapezoidal vertical leg at one side and another side

matching to horizontal cross section 50x25. The spacers shall

be made of Polycarbonate (PC). For ease of wire management,

a 300 mm length & 142mm breadth flip up cover made up of

aluminum having soft closure should be provided. A flip down

mechanism enabled cable tray shall be provided below the

worktop to mount switches and sockets. Metal cable tray shall

be made of 0.8mm thick CRCA sheet with separator for data

The overall size of workstation shall be 2400L x 900D x

750H.The worktop shall be made of 25mm thick pre laminate

partical boards with E1 norms dully finish with 2mm pvc edge

band all the side of worktop. Modesty shall be made of 18mm

thick pre laminate partical boards with E1 norms with 2mm pvc

edge band all the visible side and connected with 2 nos L-

shape pressure aluminium die casted connector. The height of

the modesty shall be 450mm. The understructure shall be made

up of MS powder coated legs having enhanced look trapezoidal

cross section size 52mm x 52mm x 52mm x 26mm with

chamfered corners and thickness of 1.6mm. Edges of the leg

should not have sharp edges. For safety of users a radius of

R3.20 mm should be provided. The Trapezoidal tube shall be

connected with die cast connectors at top, leg shoe & levelers at

bottom. High pressure aluminum die cast connectors shall of

ADC-12 material confirming to ASTM E 1251-2011, IS 7658-

1990 & IS 11035 – 1190. The vertical legs shall be connected

by horizontal beams with the help of aluminum die cast

connector that joints the legs vertically and horizontally with pipe

of cross section 50 x 25 mm x 1.6 mm thickness. The die cast

connect size shall be L shaped having angle of 10 degrees for

vertical leg side. The Diecast connector will have same shape

as of Trapezoidal vertical leg at one side and another side

matching to horizontal cross section 50x25. The spacers shall

be made of Polycarbonate (PC). For ease of wire management,

a 450 mm length & 142mm breadth flip up cover made up of

aluminum having soft closure should be provided. A flip down

mechanism enabled cable tray shall be provided below the

worktop to mount switches and sockets. Metal cable tray shall

be made of 0.8mm thick CRCA sheet with separator for data

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

The overall size of workstation shall be 1200L x 600D x

750H.The worktop shall be made of 25mm thick pre laminate

partical boards with E1 norms dully finish with 2mm pvc edge

band all the side of worktop. Modesty shall be made of 18mm

thick pre laminate partical boards with E1 norms with 2mm pvc

edge band all the visible side and connected with 2 nos L-

shape pressure aluminium die casted connector. The height of

the modesty shall be 450mm. The understructure shall be made

up of MS powder coated legs having enhanced look trapezoidal

cross section size 52mm x 52mm x 52mm x 26mm with

chamfered corners and thickness of 1.6mm. Edges of the leg

should not have sharp edges. For safety of users a radius of

R3.20 mm should be provided. The Trapezoidal tube shall be

connected with die cast connectors at top, leg shoe & levelers at

bottom. High pressure aluminum die cast connectors shall of

ADC-12 material confirming to ASTM E 1251-2011, IS 7658-

1990 & IS 11035 – 1190. The vertical legs shall be connected

by horizontal beams with the help of aluminum die cast

connector that joints the legs vertically and horizontally with pipe

of cross section 50 x 25 mm x 1.6 mm thickness. The die cast

connect size shall be L shaped having angle of 10 degrees for

vertical leg side. The Diecast connector will have same shape

as of Trapezoidal vertical leg at one side and another side

matching to horizontal cross section 50x25. The spacers shall

be made of Polycarbonate (PC). For ease of wire management,

a 300 mm length & 142mm breadth flip up cover made up of

aluminum having soft closure should be provided. A flip down

mechanism enabled cable tray shall be provided below the

worktop to mount switches and sockets. Metal cable tray shall

be made of 0.8mm thick CRCA sheet with separator for data

The overall size of Chair shall be width 600 +/-5mm, depth 640

+/-5mm. Total height shall be 980 to 1080 +/-5 mm, Back Width

425 mm at Top and 500mm at bottom, Seat Width 500 +/-5 mm,

Seat Depth 470+/-5 mm and Seat height 470mm to 570 mm +/-

5mm range. Seat shall be made up of foam pre moulded at 55

kg/m3 density. hardness of 25+ 3kgf at 50% deflection

conforming to IS 3400. Seat shall be uplhostered with micro

fabric 100% polyster 180 GSM abrasion > 50000 cycles. Fire

rated fabric confirming to BS EN 1021 (match) should be used.

The chair shall be supplied with Mesh Back rest. The back

frame shall be made up of Injection molded PPGF 20% in light

grey shade, armest support also in light grey shade. PPGF

Frame thickness shall be minimum 4.8mm. Adjustable Lumbar

Support made up of PU having size 365 mm x 110 mm x 25mm

thick shall be provided for better comfort. Lumbar Support

material Integrated one-piece Molded PU. The Chair should be

provided with Self Calibrating Multilock Mechanism (Bio

Snchyro mechansim) that should adjust the tension of the back

sensing weight of the user. The mechanism shall allow 360

degree revolving feature along with height adjustablility. One

Way Adjustable Arms (Height) to be provied with height

adjustment button of size 73mm x 18mm made of Delrin P 500.

Armrest Height shall be 170mm to 260mm adjustable from Seat

The mechansim shall possess seat to back recline ratio of 3:7.

The Gas Lift used shall be class 4 tested as per ANSI BIFMA

standards. Metal base shall be provided of light grey color

matching the chair back & armrest.The base shall be made up

of mild steel powder coated in grey shade to match the entire

grey theme of chair.Metal base powder coated made up of

sheet thickness 2mm.Tolerance of +/- 5mm to be considered for

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

The overall size of Low height storage shall be 1200 x 450 x

750 (WDH) mm. Top shall be made up of 18mm thick pre

laminated particle board E1 norms and Back shall be made up

of 9 mm thick pre laminated particle board with 2mm PVC edge

lipping, Shutters shall be made up of 18 mm thick pre laminated

particle board. Shutters to be provied for compartment. The

storage shall have adjustable shelf. Edge: All exposed shall be

sealed with 2mm thick PVC edge lipping. The hinged doors top

shall be provided with finger groove handle-less design for a

NSF-16 streamlined look. Finger gAroove shall be created by providing each 6.00 16376.00 ₹ 98,256.00

a reverse tapered profile edge of 6mm straight surface & 12 mm

tapered towards inside @ 45 degree & then sealed with

minimum 2mm thick PVC lipping on automatic machine. Cam

Lock faciltity should be provided for safe storage of documents.

The OEM shall have ISO 9001, BIFMA Level 2, Green Guard

UL Gold Certification, AIOTA, IGBC Gold rated factory

certification and India Design Mark.

Metal Almirah : Overall Size shall be 900 x 400 x 1981 (WDH)

mm. The complete storage shall have metal shutter and metal

top. The construction and material of storage body shall be of

0.8mm thick CRCA and skirting shall be of 0.8mm thick CRCA

sheet. The storage top shall be of 0.8mm thick CRCA sheet and

shutters shall be of 0.8mm thick CRCA sheet. Shelf shall be

mounted with the Metal shelf support made of 2mm thick CRCA

sheet with Nickel or Chrome plating. The construction shall be

aesthetically appealing completely welded/ knockdown. Hinges

of Hettich/Ebco make shall be used for shutter support. Legs

shall be fitted with M10 screw leveler with height adjustment

NSF-17 upto 12mm to 15mm. 3 point lock of Ebco/hettic make shall be each 26.00 53987.00 ₹ 14,03,662.00

used. Recessed handles of Hettich/ebco make shall be

provided. Finish shall be powder coated with the thickness of 50-

60 μ.Tolerance of +/- 10mm to be considered for product sizes

i.e Length, Depth & height and tolerance of 5% to be considered

in thickness & sizes of pipe. The OEM shall have ISO 9001,

BIFMA Level 2, Green Guard UL Gold Certification, AIOTA,

IGBC Gold rated factory certification and India Design Mark.

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Overall size of table shall be of size 2400 L x 1200D x 750 H

(mm). The main worktop size shall be made of 25mm thick pre

laminate partical boards with E1 norms dully finish with 2mm

pvc edge band all the side of worktop. The understructure shall

be made up of MS powder coated legs having enhanced look

trapezoidal cross section size 52mm x 52mm x 52mm x 26mm

with chamfered corners and thickness of 1.6mm. Edges of the

leg should not have sharp edges. For safety of users a radius of

R3.20 mm should be provided. The Trapezoidal tube shall be

connected with die cast connectors at top, leg shoe & levelers at

bottom. High pressure aluminum die cast connectors shall of

ADC-12 material confirming to ASTM E 1251-2011, IS 7658-

1990 & IS 11035 – 1190. The vertical legs shall be connected

by horizontal beams with the help of aluminum die cast

NSF-18 connector that joints the legs vertically and horizontally with pipe each 2.00 46373.00 ₹ 92,746.00

of cross section 50 x 25 mm x 1.6 mm thickness. The die cast

connect size shall be L shaped having angle of 10 degrees for

vertical leg side. The Diecast connector will have same shape

as of Trapezoidal vertical leg at one side and another side

matching to horizontal cross section 50x25. Understructure shall

powder coated upto 40 to 60microns. The OEM shall have ISO

9001, BIFMA Level 2, Green Guard UL Gold Certification,

AIOTA, IGBC Gold rated factory certification and India Design

The overall size of Chair shall be Total height 840+/-3 mm, Over

all chair width should be 535 +/-5mm and Overall chair depth

should be 535 +/-5mm. Back Width 360mm at Top and 440mm

at bottom, Seat Width 420 +/-3 mm, Seat Depth 425+/-3 mm

and Seat height 450mm +/-5mm. Seat and back shell should

made by injuction moulding process with plastic material of

PPGF20%. Seat and back shall be provided with cushion with

fabir Upholstered. The Chair understructure should be provided

with 12 mm thickness MS rod loop legs with rod conforming to

NSF-19 IS – 7887. Injuction moulded Polycarbonate Leg shoes shall each 12.00 7780.00 ₹ 93,360.00

assembled to understructure. seat assembled shall be with

silicon bushes to ensure stratch free when chairs stached.

Understructure shall powder coated upto 40 to 60microns. The

OEM shall have ISO 9001, BIFMA Level 2, Green Guard UL

Gold Certification, AIOTA, IGBC Gold rated factory certification

and India Design Mark.

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Single Side Book Rack : The overall size of the book rack shall

be 950 L X 350 D X 1950 (LDH)mm.The Top and Side Panel

shall be made of 18mm thick pre laminated partical boards with

E1 norms and all visible side 2mm pvc edge bending. 40mm

skirting shall be provided at bottom fo size 18mm thick pre

laminated partical boards with E1 norms and all visible side

2mm pvc edge bending. Back Side Covered with Powdercoated

CRCA sheet of 0.8mm thickness. with both side MS Vertical

Pole of size 40 x 40 x 1.6. These pole comes with slotted cuts

for holding the adjustable shelves. Powder Coated Adjustable

shelves comes of size 900LX315D of 1.2mm thick sheet with

20mm straight edges of all side. all the shelves comes with u

NSF-20 shape center support at bottom side of the shelf of each 4.00 34637.00 ₹ 1,38,548.00

20WX10HX800L. 2.2 mm thick CRCA l bracket shall be

provided for supporting the shelves.Levelar shall be provided at

bottom. Tolerance of +/- 5mm to be considered for product sizes

i.e Length, Depth & height and tolerance of 5% to be considered

in pipe thickness & Pipe sizes. The OEM shall have ISO 9001,

BIFMA Level 2, Green Guard UL Gold Certification, AIOTA,

IGBC Gold rated factory certification and India Design Mark.

The worksurface of the table shall be made up of 25mm thick

Pre-laminate particle board as per E1 norms and its edges duly

sealed with 2mm PVC Lipping on automatic machine at visible

sides. Two Long sides of the work surface shall be provided

with reverse tapered edge design created by chamfering the

board at 45 degree inside for 17mm length & keeping 8mm

straight & then edges sealed with 2mm thick PVC Lipping on

automatic machine. Leg: shall be made up of high pressure

aluminum die casted 20 degree tapered, number “7” shape &

oblong cross section of about 55mm on top, 45mm at bottom

and of 725mm length to get 750mm table height, it shall acts as

vertical structural support member, connected by a horizontal

cross beams 50x25x1.6thk (16g) ERW tube & connected to the

Aluminium diecast vertical legs through a high pressure

Aluminium diecast 90deg – 02 way connectors. The

Intermediate leg: Two Verticals of Intermediate leg will have to

be with 60x40mm rectangular ERW tubes and both legs are

joined using a beam section of 40x40x1.6mm thk at the top

side. The 60x40 verticals to have through “U” notch or through

cut out of 40x41mm size at the top side to locate 40x40 cross

beam. Understructure shall powder coated upto 40 to

60microns. Wire Management: 450mm Aluminium Flip Up and

provision to mount swicthes and sockets on PVC cable dump

and Vertical wire entry cover made up of steel sheets. The OEM

shall have ISO 9001, BIFMA Level 2, Green Guard UL Gold

Certification, AIOTA, IGBC Gold rated factory certification and

India Design Mark.

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

The overall size of The Board room table shall be

4200LX1200DX750H. The main table size shall be

2400LX600X750Hmm. The main(Head) table shall be provided

on both side. and add on table size shall be

1500LX600DX750H. Add on table shall be provided 02 nos. on

each sides. The main table worktop size shall be 2400x600

made of 25mm thick pre laminate partical boards with E1 norms

dully finish with 2mm pvc edge band all the side of worktop.The

addon table Top size shall be 1500Lx600made of 25mm thick

pre laminate partical boards with E1 norms dully finish with 2mm

pvc edge band all the side of worktop. Modesty shall be made

of 18mm thick pre laminate partical boards with E1 norms with

NSF-23 2mm pvc edge band all the visible side. The height of the each 1.00 149178.00 ₹ 1,49,178.00

modesty shall be 450mm.And the gable end shall be made of

25mm thick pre laminate partical boards with E1 norms dully

finish with 2mm pvc edge band all the side.Wire Management:

450mm Aluminium Flip Up and provision to mount swicthes and

sockets on Metal cabletray and Vertical wire entry cover made

up of steel sheets. The OEM shall have ISO 9001, BIFMA Level

2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated

factory certification and India Design Mark.

The overall size of Chair shall be : Total height 1050 to 1150 +/-

5 mm, Back Width 480 mm at Top and 470mm at bottom, Seat

Width 490 +/-5 mm, Seat Depth 460+/-5 mm and Seat height

440mm to 540 mm +/-5mm range. And over all chair width

should be 560 +/-5mm and Overall chair depth should be 660 +/-

5mm. Seat and back should be made up of foam pre moulded

at 55 kg/m3 density. hardness of 25+ 3kgf at 50% deflection

conforming to IS 3400. Seat and back shall be upholstered with

100% polyster fabric of 295 GSM abrasion > 50000 cycles. No

flamming or progressive smoldering within one hour of

placement of the cigarettes. Fire rated fabric confirming to BS

EN 1021 (match) should be used. The Chair should be provided

with synchro mechanism with single lever with one position lock.

The mechanism shall allow 360 degree revolving feature along

with height adjustablility. One Way Adjustable Arms (Height) to

be provied with height adjustment button made of Delrin P 500.

The mechansim shall possess seat to back recline ratio of 3:7.

The Gas Lift used shall be class 4 tested as per ANSI BIFMA

standards. Nylon Base to be provied. Twin castors 50 mm dia

with PA6 material complying to ANSI/ BIFMA X 5.1 2017

standards. the axle pin shall be rust protected zinc passivated.

The base shall be 660 mm PCD (26 inches) five pronged bases

made up of PA6, 30% glass filled reinforced with bottom ribbing

for additional buttress and strength. Tolerance of +/- 5mm to be

considered for product sizes i.e Length, Depth & height and

tolerance of 5% to be considered in pipe thickness & Pipe sizes.

The OEM shall have ISO 9001, BIFMA Level 2, Green Guard

UL Gold Certification, AIOTA, IGBC Gold rated factory

certification and India Design Mark.

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

The overall size of Chair shall be : Total height 950 – 1050 +/-5

mm, Back Width 480 mm at Top and 470mm at bottom, Seat

Width 490 +/-5 mm, Seat Depth 460+/-5 mm and Seat height

440mm to 540 mm +/-5mm range. And over all chair width

should be 560 +/-5mm and Overall chair depth should be 660 +/-

5mm. Seat and back should be made up of foam pre moulded

at 55 kg/m3 density. hardness of 25+ 3kgf at 50% deflection

conforming to IS 3400. Seat and back shall be upholstered with

100% polyster fabric of 295 GSM abrasion > 50000 cycles. No

flamming or progressive smoldering within one hour of

placement of the cigarettes. Fire rated fabric confirming to BS

EN 1021 (match) should be used. The Chair should be provided

with synchro mechanism with single lever with one position lock.

The mechanism shall allow 360 degree revolving feature along

with height adjustablility. One Way Adjustable Arms (Height) to

be provied with height adjustment button made of Delrin P 500.

The mechansim shall possess seat to back recline ratio of 3:7.

The Gas Lift used shall be class 4 tested as per ANSI BIFMA

standards. Nylon Base to be provied. Twin castors 50 mm dia

with PA6 material complying to ANSI/ BIFMA X 5.1 2017

standards. the axle pin shall be rust protected zinc passivated.

The base shall be 660 mm PCD (26 inches) five pronged bases

made up of PA6, 30% glass filled reinforced with bottom ribbing

for additional buttress and strength. Tolerance of +/- 5mm to be

considered for product sizes i.e Length, Depth & height and

tolerance of 5% to be considered in pipe thickness & Pipe sizes.

The OEM shall have ISO 9001, BIFMA Level 2, Green Guard

UL Gold Certification, AIOTA, IGBC Gold rated factory

certification and India Design Mark.

Sub Total of Furniture NDSR Amount ₹ 71,20,255.00

DSR 2025 Electrical work

SUB HEAD-I:CIRCUIT CUM POINT WRING. ₹ 0.00

Supplying, installation, testing & commissioning of Race way

made from minimum 2.0 mm thick GI raceway, factory

fabricated, with internal partition of the following sizes including

providing removable double folded cover of 2.0 mm thick ,

knock out holes and fixing accessories & coupling, earthing stud

for terminating 8 SWG copper earth wire complete Supports,

NSEL-1 bends, access boxes, tap off boxes and cross over as per site ₹ 0.00

requirement. (overhead / wall mounted recovery & junction

boxes shall be 2.0 mm thick). The pregalvenised sheet shall be

as per IS 277 or BS 2989 having tensile strength of minimum

500 N/sq.m. and minimum zinc coating of 275 GSM & coupler

plate. as required

NSEL- 1.1 100 mm wide x38 mm deep in ceiling/floor Metre. 100.00 616.00 ₹ 61,600.00

NSEL- 1.2 225 mm wide x38 mm deep in ceiling/floor Metre. 80.00 1100.00 ₹ 88,000.00

NSEL- 1.3 300 mm wide x38 mm deep in ceiling/floor Metre. 10.00 1391.00 ₹ 13,910.00

JUNCTION BOX : ₹ 0.00

Supplying, installation, testing & commissioning of floor/ceiling

recessed 2 mm thick pregavanised sheet outlet junction box

including providing cover with provision to adjust overall height,

knock outs on four sides to accept raceways of specified sizes

and cutouts to fix required outlets for following size of race ways

with painted GI plate ( Colour as approved

Architect/Consultant).

EXTERNAL LIGHT FIXTURES. ₹ 0.00

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Supply, Installation, Testing and Commissioning of 5m Conical

Pole with single arm. Material for pole section: Hot rolled

product of non alloy structural steel grade S355, Other parts:

MS as per IS 2062. Material as per BS EN 10025 equivalant to

Indian standard.. Bottom (O.A.F.) 130mm and top (O.A.F.)

NSEL-3 70mm. Size of Base Plate: 220 SQ, thickness of base plate Each 22.00 13245.00 ₹ 2,91,390.00

should be minimum 12mm, hole PCD 220, Fdn. bolt of M16.

Tolerance on material thickness as per IS:1852/85. Pole shall

be hot dip galvanized as per IS: 2629. 5mtr. octagonal pole with

single arm of 500mm length and 48.3mm dia .as required .

Supply, Receiving, Unloading, Shifting, Installation, Testing &

commissioning of 35W LED Post top luminaire consisting of a

high-pressure powder coated die-cast aluminium housing, a

canopy made of plastamid and a UV resistant high impact

polycarbonate protector. The luminaire emits a pleasant, glare-

free light due to the highly efficient white reflector (symmetrical

NSEL-4 light distribution). The complete luminaire is sealed to IP 66 & Each 2.00 12057.00 ₹ 24,114.00

Impact resistance of IK08. Electronic temperature monitoring

prevents overheating of LEDs and power supply within the LED

compartment (ThermiX®). It is designed for LED light sources of

25W having a neutral white light. Surge protection of 10kV. (For

Entrance Gate).as required .

Supply, Installation, Testing & commissioning of IP65 8W LED

Bollard with dark grey polyester coated rust proof Die cast

Aluminium housing, with symmetrical dual optics and PC

diffuser The luminaire shall have initial system lumen of 400lm

with System efficacy of >50Lumen/W. The LED shall have a

CCT of 3000K with LEDs shall be LM80 Compliant with TM21

report for life of 25000 hrs at 35 Deg C. and CRI 80 with beam

angle of 360°.The Fixture shall have IP65 potted driver with

THD<25%, PF>0.9, with operating volatge range of 180-270V.

The fixture shall comply with IS 10322 part 5/Sec 1 1987 and

LM79 LM80 reports are tested and certified by NABL accredited

Lab. (for landscaped area).as required .

Supply, Installation, Testing & Commissioning of Energy saving,

15 watt decorative UP-down Luminaire with wall surface

mounting using COB LED as light source. The fixture shall

NSEL-6 comply with IS 10322 part 5/Sec 1 1987 and LM79 LM80 Each 10.00 1800.00 ₹ 18,000.00

reports are tested and certified by NABL accredited Lab. (for

building outer wall façade).as required .

Supply, Installation, Testing and Commissioning of 10 w LED

Bulkhead with a nominal system lumen output of 1000 lumens

and a minimum system efficacy of 100 lm/W. The luminaire

shall have a rated system lifetime of 25,000 burning hours at

L70. The luminaire should have a color temperature of 5700K

NSEL-7 and CRI > 80. The luminaire shall meet IP65 rating and IK 08 Each 4.00 1663.00 ₹ 6,652.00

rating with THD < 20% and PF > 0.9. The luminaire housing

should made of pressure die cast Aluminium with

polycarbonate front diffuser. The total power consumption

should not exceed 6.5W (including driver). as required

Supply, Installation, Testing and Commissioning of HD Metal

Exhaust Fan heavy duty 230V A.C 50 cycles, 450 mm sweep,

NSEL-8 1400 rpm, energy efficient, complete erected in position with all Each 6.00 8019.00 ₹ 48,114.00

accessories, as per specification. as required .

Supply, Installation, Testing and Commissioning of heavy duty

450 mm Wall Fan .as required .

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

LED Smart Street light fixture, powder coated pressure die cast

aluminium (System. System lumen efficacy ≥105 and <120

Supplying, installation, Testing & Commissioning of Smart

Street light LED fixture, powder coated pressure die cast

aluminium body with built in or separate driver as per the

requirement ( < 700ma), Input voltage: 140-270 Volt AC,

frequency 50/60 hz, Operating temp range -5 0C to 50

0C, internal surge protection of 5 KV L,N,E as per IEC

61000-4-5, Driver efficiency >85%,THD < 10% as per IEC

61000-3-2, P. F.≥0.95, IP-66,IK 08, CRI >70, under voltage

and over voltage protection, EMI- EMC as per CISPR-15,

lenses for beam angle as per IESNA type I/II/III as per the

width of the road and the project requirement., suitable to fit in

up to 65mm dia pipe, life time of minimum 50000 Burning

Hours with 70% of initial Lumen maintained till life ends as

per LM80 extrapolation IES TM-21-11 report, CCT 3000°K /

4000°K / 5700°K /6500°K (As per ANSI Bin), Maximum

power consumption should not more than the specified rating

and Fixture shall be of relevant BIS standard complete in all

respect i/c external connections with 1.5 sq.mm

FRLS/HFFR, PVC insulated copper conductor single core

cable and earthing etc. as required with Minimum 5 year OEM

warranty. System lumen efficacy ≥105 and <120 lm/Watt

output . LM79 & LM80 Test report and all testing required for

LED fixtures as per BIS shall be submitted. Shape size and

CCT shall be as approved by Engineer-in-Charge as per

requirement. (Thermal management: heat sink of aluminium

housing such that LED junction temperature shall not rise above

90°C). Smart inbuilt controller shall have following features.

8.21.3 35 Watt (System lumen efficacy >120 lm/Watt) Each 7.00 29329.00 ₹ 2,05,303.00

NSEL-10 SUB HEAD-VI- H. T & L.T. CABLES. ₹ 0.00

Supply of following sizes of XLPE insulated Aluminum

conductor strip/ wire Armoured, overall PVC sheathed 1.1 KV

NSEL-10 grade cables conforming to relevant IS-7098 Code and ₹ 0.00

technical specifications.

Laying of one number PVC insulated and PVC sheathed /

DSR-2025- XLPE power cable of 1.1 KV grade of following size in the

10.6 existing masonry open duct as required.

10.6.2 Above 35 sq. mm and upto 95 sq. mm Meter 200.00 58.00 ₹ 11,600.00

10.6.4 Above 185 sq. mm and upto 400 sq. mm Meter 500.00 146.00 ₹ 73,000.00

Supplying and making end termination with brass compression

gland and aluminium lugs for following size of PVC insulated

and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV

grade as required.

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

NSEL-11 L.T. COPPER CABLES.

Supplying, laying & termination of following 1.1 kV grade, heavy

duty XLPE insulated PVC Sheathed Copper Conductor FRLS

type armoured cables suitable for 415V, 50Hz,AC system, with

inner and outer PVC sheath, outer sheath provided with FRLS

NSEL-11 insulation, galvanised steel armouring (roundor

flatasmentioned) and with all components as mentioned in

BOQ, specifications and schedule,completeetc. as required.

NSEL-12 H.T. CABLES. ₹ 0.00

Supply & Testing of following 11 KV( UE) grade multicore

Aluminium conductor XLPE insulated cable, insulation

screening with extruded semi conducting compound in

combination with copper tape armoured cores laid up, inner

NSEL-12 sheath of PVC tape, galvanised steel flat strip armoured and ₹ 0.00

overall PVC sheathed cable conforming to IS: 7098 (Part - II)

and complete with all latest amendments etc. complete as

HT CABLE LAYING ₹ 0.00

NSEL-13 H T PANEL & L T PANEL.

11KV HT PANEL (SINGLE BOARD INCOMING CUM

11 kV, 31.5kA 3Sec 630A VCB with motorized spring charge

closing mechanism with inbuilt antipumping protection (with out

seperate relay )and trip free features, Floor rolled VCB, internal

arctypetested design 31.5kA for 1Sec. with inbuilt earth

switch,motor voltage 230V AC and tripping / closing coil voltage,

110V DC and VCB complete with 4 NO + 4 NC auxiliary switch

contact as spare complete with

i 230 V AC spring charge meter.

ii 110 V DC shunt trip coil.

Sets of three phase draw out type PTof ratio 11kV/√3 :110V/√3,

Class.0.5 per phase with control fuses.

Sets of 100-50/5-5A, class 0.5 accuracy, burden 7.5 VA current

iv transformer (cast resin) for metering, ISF<5 .

Sets of 100-50/5-5A, class 5P10 accuracy, burden 7.5 VA

Current Transformer for protection, ISF<5.

(0-300) digital Ammeter with selector switch and required CTs.

(0-11kV) digital Voltmeter with selector switch and required

One (1) No. Multifunction meter with RS-485 Port suitable for

measurement of voltage, currents, power factor, frequency,

viii Energy (KWH, KVARHKVAH), Power (KW, KVA andKVAR),

harmonics and maximum demand indication

One (1) Set of Multifunctional protection relay with RS485

Communication Compatibility & protection. 50,51,50N,51N

x Mater Trip Relay - 86

xi U/V & O/V Relay - 27-58

xii Trip Circuit Supervison relay - 95

xiii Ground fault Relay - 63X

xiv Breaker control switch : (Trip-Neutral- Close)

xv Sets of phase & breaker ON/OFF indicating lamps.

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

xvi 5/15 A five pin socket +15A switch.

Sets of circuit breaker ON /OFF /Trip / Spring charged /

Tripcircuithealthy indicating lamps

xviii 100 W anticondensation space heater control by thermostat

xix Mechanical ON/OFF/Trip indication.

NSEL-13.1 11 KV panel VCB Switchboard as described above Set 1.00 719823.00 ₹ 7,19,823.00

NSEL-13.2 MAIN LT Panel

Supplying, installation, testing & commissioning of cubical type

LT panel suitable for 415V, 3 Phase, 4 Wire 50 Hz Ac supply,

fabricated in compartmentalized (preferably) design from CRCA

sheet steel of 2mm thick for frame work and covers, 3mm thick

for gland, plates i/c cleaning & finishing complete with 9 tank

process for powder coating in approved shade, having TPN

aluminium alloy bus bars of hight conductivity, DMC / SMC bus

bars of high conductivity, DMC/ SMC bus bar supports, with

short circuit withstand capacity of 31 MVA for 1 Sec., bottom

base channel of MS section not less than 100mmx 50mm x

5mm thick, fabrication shall be done in transportable sections,

entire panel shall have a common copper earth bar of size

25mm x 5mm at the rear with 2 Nos. earth stud, solid

connections from main bus bar to switch gears with required

size of Al. bus bars and control wiring with 2.5 sq. mm. PVC

insulated coppr conductor S/C cable, cable alleys, cable gland

plates in two half, i/c providing following switch gears :-

(Note:The contractor may select the next higher fault rating of

MCCB if it is not readily available ,without any extra cost ,as the

figure indicated within the bracket are required maximum fault

level of the panel).

A From 250 KVA Transformer

1No. 500 A, 4P MCCB (50 KA )having Mircroprocessor based

releases for O/L, S/C & E/F protection.

1 No. SPD Type 1

1Set-digital multi function meter (showing harmonics along

withall other electrical parameters such as voltage, current,Hz,

KW, KWHr, PF.) with RS 485 port with matching cast resin CT's

1Set-0-500V, digital Voltmeter with selector switch, 3No. Phase

indicating LED lamp to show the incoming power with control

1Set indicating LED lamps for MCCB On /Off/ Trip with

protective SP MCB's.

1 Set of CTs of the ratio 500/5A, Class-1 for APFC Relay,

1Set of CTs of the ratio 500/5A with Class1 Accuracy for

Metering, burden 15 VA

1 No. 500/5A , 15 VA, Class-5P10 CT's for Protection

1 No. Under Voltage relay

1 No. over Voltage relay

B INCOMER FROM DG Set

From 250 KVA DG Set

1No. 500 A, 4P MCCB (50KA )having Mircroprocessor based

releases for O/L, S/C & E/F protection.

One set Solar provision shall be made as per site conditions.

1 No. SPD Type 1

1Set-digital multi function meter (showing harmonics along

withall other electrical parameters such as voltage, current,Hz,

KW, KWHr, PF.) with RS 485 port with matching cast resin CT's

1Set-0-500V, digital Voltmeter with selector switch, 3No. Phase

indicating LED lamp to show the incoming power with control

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

1Set indicating LED lamps for MCCB On /Off/ Trip with

protective SP MCB's.

1 Set of CTs of the ratio 500/5A, Class-1 for APFC Relay,

1Set of CTs of the ratio 500/5A with Class1 Accuracy for

Metering, burden 15 VA

1 No. 500/5A , 15 VA, Class-5P10 CT's for Protection

1 No. Under Voltage relay

1 No. over Voltage relay

TPN aluminium bus bars of minimum of 600 Amps capacity with

heat shrinkable coloured sleeves and i/c DMC /SMC bus bar

cross section, size supports & their spacing etc. for with

standing fault level of 31MVA for 1 sec.

D INTERLOCKING.

Electrical through advance contacts in MCCB/ACB's (Incomer

&bus couplers)&mechanical (castel key) interlocking should be

provided to ensure that only one supply is available at a time on

each section of bus & to eliminate any possibility of accidentally

approaching two supplies at one bus section.

EACH OUTGOING FEEDER SHALL HAVE DUAL SOURCE

DIGITAL MFM & ON-OFF INDICATION LAMP

2 Nos. 200A TP+N Moulded Case Circuit Breaker with

microprocessor based adjustable over current, short circuit,

earth fault protections, ON /OFF indication (Isc=35kA).

3 Nos. 100A TP+N Moulded Case Circuit Breaker with

microprocessor based adjustable over current, short circuit,

earth fault protections, ON /OFF indication (Isc=20kA).

2 Nos. 40A TP+N Moulded Case Circuit Breaker with

microprocessor based adjustable over current, short circuit,

earth fault protections, ON /OFF indication (Isc=20kA).

3 N0.Space for 63 A MCCB

100 KVAR CAPACITOR - SHALL BE PART OF MAIN L.T.

1 No 250 Amp FP Moulded Case Circuit Breaker. (To be

considered in Main L.T. Panel)

1 Nos. 0 to 500 Volt digital voltmeter with Voltmeter Selector

Switch & Protective SP MCB (96mm square).

1 No. 0 to 500 Amp digital ammeter (96mm square) with CT's)

1 Sets of phase indicating lights (RYB) with protection fuses.

1 Sets breaker 'ON' & 'OFF' indicating lamp.

10 Step Automatic Power Factor Correction relay (APFC relay).

2 Nos. capacitor duty contactor (one for each 10KVAR capacitor

4 Nos. capacitor duty contactor (one for each 20KVAR capacitor

2 Nos. 10 KVAR Capacitor Bank 525 Volt with 14% reactor.

4 Nos. 20KVAR Capacitor Bank 525 Volt with 14% reactor.

6 sets of push button stations Red and Green for manual

operation of capacitor units with auto/manual selector switches.

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

1 No. Indicating lamp for each 50 / 25 KVAR capacitor unit to

indicate that the unit is 'ON'.

1 No. Toggle switch for changing automatic to manual operation

of capacitor units.

NSEL-13.2 Main LT Panel describe as above Set 1.00 1714619.00 ₹ 17,14,619.00

NSEL-13.3 M V PANEL FOR MAIN BUILDING FLOOR PANEL .

A INCOMER FROM EXISTING MAIN LT PANEL

1 Nos. of 200 A, 4P MOTORISED type MCCB with

Ics=Ics=35KA having Mircroprocessor based releases for O/L,

S/C & E/F protection.

1 Nos. SPD Type 1

1 Sets - digital multifunction meter (showing harmonics along

with all other electrical parameters such as voltage, current, Hz,

KW, KWHr, PF.) with RS 485 port with matching cast resin CT's

1 Sets - 0-500V, digital Voltmeter with selector switch, 3 No.

phase indicating LED lamp to show the incoming power with

control SP MCB.

METERING & INDICATION

1 set of R,Y,B phase indicating lamps

1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP

1 No. (0-400A) Ammeter with ASS with 3 nos. 300/5A CT's

1 Set of 300 A TPN Aluminium Bus Bar with colour coded PVC

i) 2 No. 63A 4P MCCB (20 KA)

ii) 4 No. 40A 4P MCCB (10 KA)

iii) 2 No. 63A 4P MCCB (20 KA) (SPARE)

iv) 2 No. 40A 4P MCCB (10 KA) (SPARE)

NSEL-13.3 Main LT Panel describe as above Set 1.00 408860.00 ₹ 4,08,860.00

NSEL-13.4 M V PANEL FOR HVAC PANEL .

A INCOMER FROM EXISTING MAIN LT PANEL

1 Nos. of 200A, 4P MOTORISED type MCCB with

Ics=Ics=35KA having Mircroprocessor based releases for O/L,

S/C & E/F protection.

1 Nos. SPD Type 1

1 Sets - digital multifunction meter (showing harmonics along

with all other electrical parameters such as voltage, current, Hz,

KW, KWHr, PF.) with RS 485 port with matching cast resin CT's

1 Sets - 0-500V, digital Voltmeter with selector switch, 3 No.

phase indicating LED lamp to show the incoming power with

control SP MCB.

METERING & INDICATION

1 set of R,Y,B phase indicating lamps

1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP

1 No. (0-250A) Ammeter with ASS with 3 nos. 300/5A CT's

1 Set of 300 A TPN Aluminium Bus Bar with colour coded PVC

i) 4 No. 63A 4P MCCB (20 KA)

ii 4 No. 40A 4P MCCB (10 KA)

iii) 2 No. 63A 4P MCCB (20 KA) (SPARE)

iv) 2 No. 40A 4P MCCB (10 KA) (SPARE)

NSEL-13.4 Main LT Panel describe as above Set 1.00 436213.00 ₹ 4,36,213.00

M V PANEL FOR ELECTRICAL VEHICLE CHARGER PANEL

A INCOMER FROM EXISTING MAIN LT PANEL

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

1 Nos. of 100 A, 4P MOTORISED type MCCB with

Ics=Ics=20KA having Mircroprocessor based releases for O/L,

S/C & E/F protection.

1 Nos. SPD Type 1

1 Sets - digital multifunction meter (showing harmonics along

with all other electrical parameters such as voltage, current, Hz,

KW, KWHr, PF.) with RS 485 port with matching cast resin CT's

1 Sets - 0-500V, digital Voltmeter with selector switch, 3 No.

phase indicating LED lamp to show the incoming power with

control SP MCB.

METERING & INDICATION

1 set of R,Y,B phase indicating lamps

1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP

1 No. (0-150A) Ammeter with ASS with 3 nos. 300/5A CT's

1 Set of 150A TPN Aluminium Bus Bar with colour coded PVC

i) 4 No. 63A 4P MCCB (20 KA)

ii) 2 No. 40A 4P MCCB (10 KA)

iii) 2 No. 63A 4P MCCB (20 KA) (SPARE)

iv) 2 No. 40A 4P MCCB (10 KA) (SPARE)

NSEL-13.5 Main LT Panel describe as above Set 1.00 390144.00 ₹ 3,90,144.00

NSEL-13.6 FRONT OPERATED FEEDER PANEL

Supply, installation, testing and commissioning of outdoor front

operated, front access, totally enclosed, free standing, dust and

vermin proof Panel with IP65 ingress protection, fabricated from

2 mm thick CRCA sheets, with hinged, gasketted and lockable

doors including the cost of interconnections, copper crimping

lugs, brass glands, bonding to earth and painting, suitable for

use at 415 volts, 3 phase 4 wire 50 Hz system with 31 MVA

rupturing capacity at 415 volts complete as per specifications,

as required and as below.

External lighting Feeder piller

1 No. 40A,4P MCCB (25kA) and ON/OFF indicating lamps.

1 No. 40A, 3 phase Timer Switch for automatic operation.

B METERING & INDICATION

i) 1 set of R,Y,B phase indicating lamps.

1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP

1 No. (0-40A) Ammeter with ASS with 3 nos. 160/5A CT's.

1 Set of 100A TPN Aluminium Bus Bar with colour coded PVC

12 nos 16 Amp 4P MCB, 10 KA.

Main LT Panel describe as above

SUB HEAD - IV:- COMMUNICTION CABLE & DRAIN PIPE.

COMMUNICTION CABLE. ₹ 0.00

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Supplying following 1.1kV grade,Communition Cables armoured

cables suitable for 415V, 50Hz, AC system, with inner and outer

PVC sheath, outer sheath provided with FRLS insulation,

galvanised steel armouring (round or flat as mentioned) and ₹ 0.00

with all components as mentioned in BOQ, specifications and

schedule, complete etc. as required.( use for VRV System).

DRAIN PIPE ₹ 0.00

Supply, installation, testing and commissioning of UPVC

condensate drain water piping of density 20Kg/m³ completewith

fittings likeelbows, tees, reducers, bends, flanges, supports &

dulyinsulated with "O" class Closed Cell Elastomeric Nitrile ₹ 0.00

Rubber of specified pipe section of specified thickness etc. as

required and of following sizes.

NS-14.2 25 mm dia pipe, with 6 mm Insulation. Meter. 450.00 360.00 ₹ 1,62,000.00

NS-14.3 32 mm dia pipe, with 6 mm Insulation. Meter. 250.00 457.00 ₹ 1,14,250.00

NS-14.4 40 mm dia pipe, with 6 mm Insulation. Meter. 100.00 554.00 ₹ 55,400.00

NSEL-15 SUB HEAD - V:- INLINE FAN & AXIL FLOW FAN. ₹ 0.00

Accoustically Insulated Box Type Inline Fans ₹ 0.00

Supplying, installing, testing and commissioning of INLINE

FANS suitable for installing in any position in vertical or

horizontal ducts. The casing shall be double skin, internally

acoustically lined and constructed of galvanised steel. with

efficient motor, fire retardent double layer canvass connection ₹ 0.00

etc complete in all respect & of following capacities. The casing

shall be selected for lower noise level. Fan motor shall have

inbuilt speed controller.

NSEL-15.1 750 CFM (15mm static pressure, single phase) Nos. 2.00 35714.00 ₹ 71,428.00

NSEL-16 Axial Flow Fan ₹ 0.00

Supply, installation, testing and commissioning of ceiling

mounted axial flow fans complete with adjustable pitch cast

aluminium alloy impeller, heavy gauge MS/GI long casing,

TEFC squirrel cage induction motor (minimum IE3 efficiency)

with Class H insulation, support frame, antivibration mountings,

fire-retardant flexible canvas connectors, bird screens and all

associated accessories. Fan performance shall be AMCA ₹ 0.00

certified in accordance with AMCA 210 and AMCA 300. Fan

discharge velocity shall not exceed 16 m/s based on net outlet

area at scheduled airflow. Sound pressure level shall not

exceed 80 dBA at 3 m distance at duty point.

4000 CFM (15mm static pressure, Axial Fan, 960 / 1450 RPM,

NS-16.1 2.2 Kw Fan Motor or as required, 500 MM Fan Dia) Nos. 2.00 69103.00 ₹ 1,38,206.00

3500 CFM (15mm static pressure, Axial Fan, 960 / 1450 RPM,

NS-16.2 2.2 Kw Fan Motor or as required, 500 MM Fan Dia) Nos. 2.00 65000.00 ₹ 1,30,000.00

Supplying, installation, testing and commissioning of GI volume

control duct damper complete with neoprene rubber gaskets,

DSR-30.13 nuts, bolts, screws linkages, flanges etc in confirmation to sq. m. 30.00 7580.00 ₹ 2,27,400.00

SMACNA/IS and as per specifications complete etc. as

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Supply, installation, testing and commissioning of Motorized

(ON-OFF Type) duct mounted GI volume control damper with

enthalpy sensor and necessary control wire for integration

DSR-30.14 within AHU room complete with neoprene rubber gaskets, nuts, ₹ 0.00

bolts, screws linkages, flanges etc in confirmation to

SMACNA/IS and as per specifications complete etc. as

Supplying, Fixing,testing and commissioning of fire dampers in

supply air duct/main branch and return air path as and where

required of required sizes i/c control wiring,the damper shall be

motorized and spring return so as to close the damper in the

event of power failure automatically and open the same in case

of power being restored. The spring return action shall be inbuilt ₹ 0.00

mechanism and not externally mounted. The damper shall also

be closed in the event of fire signal complete as required and as

per specifications.

Supplying, Fixing, installation, testing and commissioning of

powder coated extruded aluminium Supply Air Grills with

DSR-30.15 aluminium volume control dampers in confirmation to sq. m. 20.00 9623.00 ₹ 1,92,460.00

SMACNA/IS and as per specifications complete etc. as

Supplying & fixing of powder coated extruded aluminium

Return Air Grills with louvers but without volume control

DSR-30.16 dampers complete in confirmation to SMACNA/IS and as per sq. m. 20.00 6285.00 ₹ 1,25,700.00

specifications complete etc. as required.

Supplying, Fixing, installation, testing and commissioning of

supply air diffusers of powder coated aluminium with aluminium

volume control dampers with anti smudge ring & removable

core in confirmation to SMACNA/IS and as per specifications

complete etc. as required.

Supplying, Fixing, installation, testing and commissioning of

Return air diffusers of powder coated aluminium without

volume control dampers with anti smudge ring & removable

core in confirmation to SMACNA/IS and as per specifications

complete etc. as required.

Supplying, Fixing, installation, testing and commissioning of

thermal insulated flexible duct of following sizes duly supported

DSR-2025- at regular interval as per site requirement etc. in confirmation to

30.19 SMACNA/IS and as per specifications complete etc. as

Supply, fixing and commissioning of Fresh/ exhaust air louvers

with section comprising of powder coated Aluminium louvers &

bird screen as required or its equivalent specifications.

Supply, fixing and commissioning of powder coated extruded

aluminium Door Transfer Grill complete with nuts, bolts, SS

screws etc. complete as required or its equivalent

specifications.

SUB HEAD-VII - ELECTRICAL WORK & CABLE TRAYS ,

RACEWAY , JUNCTION BOX.

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Supplying and installing following size of perforated pre-painted

M.S. cable trays with perforation not more than 17.5%, in

convenient sections, joined with connectors, suspended from

the ceiling with M.S. suspenders including bolts & nuts, painting

suspenders etc as required.

4.1.2 150 mm width X 50 mm depth X 1.6 mm thickness Metre. 100.00 686.00 ₹ 68,600.00

4.1.3 200 mm width X 50 mm depth X 1.6 mm thickness Metre. 50.00 775.00 ₹ 38,750.00

4.1.4 300 mm width X 50 mm depth X 1.6 mm thickness Metre. 10.00 866.00 ₹ 8,660.00

Hot Dipped Galvanized Iron Cable Tray ₹ 0.00

Supplying and installing following size of perforated Hot

DippedGalvanised Iron cable tray (galvanisation thickness not

less than 50 microns) with perforation not more than 17.5%, in

DSR 4.6 convenient sections, joined with connectors, suspended from ₹ 0.00

the ceiling with G.I. suspenders including G.I. bolts & nuts, etc.

4.6.2 150 mm width X 50 mm depth X 1.6 mm thickness Metre. 100.00 803.00 ₹ 80,300.00

4.6.4 200 mm width X 50 mm depth X 1.6 mm thickness Metre. 50.00 1062.00 ₹ 53,100.00

4.6.5 300 mm width X 50 mm depth X 1.6 mm thickness Metre. 10.00 1322.00 ₹ 13,220.00

NS-17 ISOLATOR SWITCHES WITH METAL ENCLOSURE. ₹ 0.00

Supplying, installation, testing & commissioning of 63ARCCB

(300mA),4pole switch for VRVOutdoor unitswith sheet metal

enclosure, rain protectionetc. as required tosuit thesitecondition.

NSEL-17.1 (Enclosureshall besuitable for out door installation.).Complete Each 7.00 2146.00 ₹ 15,022.00

as required as per site conditions.

Supplying, Installation, Testing and commissioning of 24-Port

1U Unloaded Universal Modular Straight Patch Panel preloaded

with cable support Bar (with slots to tie individual cable properly

at the Support Bar), Stainless Steel Rear Metal Frame,

Individual Port Transparent Shutter and Labelling, Preloaded

earthing plug for surge protection, UL 1863 Complied, CRC

NSEL18 Metal with Black Powder Coated, RoHS Compliant, Individually Each 6.00 21275.00 ₹ 1,27,650.00

Replaceable Port IO, (Shuttered IO not recommended, because

when shutter gets malfunctioned then entire IO is of no use.as

Supply, Installation, Testing & Commissioning of 4 or 6 Meter

NSEL-19 G.I Pole with foundation complete. as required. Each 5.00 21275.00 ₹ 1,06,375.00

SUB HEAD - II:- IP-EPABX SYSTEM . ₹ 0.00

Supplyiing, installation, testing and Commissioning of IP at its

core with IP switching technology and 100% non blocking

communication system with 04 Port Voicemail, 04 Port FXS, 04

Port FXO, 1 PRI Trunk lines (30 Channels) Circuit with CLIP

Facility, min 100 IP users License with provision for further

additions, 100 analog users, 01 Number IP based Operator

Console, 45 Party Conference, Speed Dial, Music on Hold,

DSR-2025- Internal/ External ring difference, Call Barring, Call Pickup. The Each 1.00 1246949.00 ₹ 12,46,949.00

38.2 system should be redundant which offer 100% duplication of

power supply and CPU card and to match the hybrid IP-PBX as

per technical specification including supporting accessories etc

complete as required. The system should have valid TEC GR

approval from DoT. as required.

Supplying, Installation, Testing & Commissioning of Type 1 IP

Phone having 2 VoIP account, 120 x40 DOT matrix screen with

38.3 backlight, Full HD duplex speaker phone, IPV6, Gigabit Each 40.00 11582.00 ₹ 4,63,280.00

Etherent, PoE etc. complete. as required.

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

SUB HEAD - III:LOCAL AREA NETWORK ( LAN ) SYSTEM.

Supplying, installation, Testing and commissioning of following

capacity 24 port Layer 2 indoor Network Switch having features

and specifications etc. as mentioned here under: At least 24 X

RJ-45 Gigabit Ethernet Ports and additional 2 X 10G Base -T

with 4 X SFP Ports with non-blocking architecture by having

Switching capacity of min. 168Gbps and packet forwarding rate

of 125Mpps or higher, 16K MAC table. Console Port, USB

port, Stacking support of min. 8 units per stack. Internal dual

AC Power supply, STP, RSTP, MSTP, BPDU Filter, BPDU

Restriction, Min. 9K Jumbo Frame, LBD, IGMP Snooping

V1/V2/V3, MLD Snopping V1/V2. IGMP /MLD Groups 1K or

more, IPv4/IPv6 Loopback Interface, 16 L3 IP Interface, Ipv6

ND, VRRPv3, UDP Helper, ECMP. VLAN: 802.1Ǫ, Port based,

Ǫ-in-Ǫ, Multicast VLAN, Protocol VLAN, VLAN Trunking,

DHCP Snopping, Server, server Screening. RADIUS ,

TACACS+ Authentication, ǪoS: 802.1P, 8 queues per port,

ǪoS : WRR, Strict+WRR, WRED, 802.1p. ACL: MAC based,

IPv4C IPv6, TCP/UDP Port number, time based ACL, TFTP

Client, SNMP V1, v2c, v3, SNMP traps, RMON, DHCP server,

relay, client, LLDP, LLDP-MED, OAM, Dying Gasp, 802.3ah,

sflow, RIP, OSPF v2/v3, policy based route, SSL, SSH. 6 kV

surge protection on all Gigabit Ethernet ports and on all GE RJ-

45 access ports. Certifications: UL, CE, FCC, RoHS, MTCTE,

OEM/Product must be on Trusted Telecom Portal of

Department of Telecommunication, Government of India etc.

complete as required.

24 port PoE Layer 2 Network Switch with PoE Support of 370W

39.3.1 or higher with each copper port supporting 802.3at PoE+ min. Nos. 6.00 125393.00 ₹ 7,52,358.00

Supplying, Installation, Testing and commissioning of indoor

Wireless Access Point for Low Density use having features and

specifications etc. as mentioned here under - Dual-band Wi-Fi6

(802.11ax) 574Mbps (2.4GHz) + 1200Mbps (5GHz), WI-FI 6

Certified, 1 x RJ45 console port, 1G LAN POE Port, factory

reset, WPA/WPA2/WPA3™ Personal/Enterprise, WEP 64/128-

bit, SSID broadcast disable, MAC address access control,

Internal RADIUS server, SNMP, Customizable Captive Portal,

Auto Channel, Works as Access Point, WDS, WDS with AP,

Wireless Client, Web (HTTP), Secure Socket Layer (SSL),

Traffic control, Support ATF/Fast Roaming/Band Steering,

Supports enhanced security – WPA-PSK/WPA2 PSK/WPA3-

PSK and RADIUS client, and Cipher negotiation, and MAC/ IP

ACL for networks, Certifications: MTCTE, CE, FCC. Should

also work as Standalone and must be Compatible with S/W &

H/W Controller with addtional features like - Real-Time

Monitoring and Alerts, Rich Advanced Features, Centralized

Device Management, Role-Based Administration, Real-Time

Monitoring, VLAN and Access Control, Auto RF Management

and Bandwidth Optimization, Multi-SSID and Captive Portal

Authentication.OEM/Product must be on Trusted Telecom

Portal of Department of Telecommunication, Government of

India etc. complete. as required.

SUB HEAD - IV:-IP CCTV SYSTEM. ₹ 0.00

Digitally signed by Om Prakash

DSR 2023 DESCRIPTION Unit Qty Rate Amount

Supplying Installation Testing and Commissioning of 5/6MP IP

DSR-2025- IR Dome Camera Having following specifications and features

1 Type of Camera: Dome Camera

Image Sensor: 1/2.8" or better progressive Scan CMOS get

color image even at night condition

3 Signal System: PAL/NTSC

Minimum Illumination: 0.008Lux@ F1.4, AGC ON, 0 lux with IR

Imaging: 1/3s to 1/30000s Shutter Support, Auto Gain Control ,

White Balance- Auto, Back Light Compensation, Multi zone

Privacy Masking, HLC, Digital Watermarking.

On Screen Display: Camera should display Camera title, Date &

Time in live & recorded video both.

7 Signal to Noise Ratio: > 50 Db.

Day & Night: True Day & Night High Performance Mechanical

IR cut filter with auto switch, IR Source Inbuilt IR LED's with

8 effective distance upto 50 Mtrs integrated IR 30 Mtrs for colour

Video Compression (Minimum): H.265 or better, Audio:-

G.711U/A, G.711Mu, G.726, AAC, G.723

10 Wide Dynamic Range: WDR (120dB or more) .

11 Digital Noise Reduction: DNR (2D/3D) On/Off .

12 Streaming: Triple streaming, configurable.

Video Streaming & Frame Rates: Triple streaming ,

13 configurable Main stream: 5/6MP @25/30 fps, Sub streams:

D1@25/30 fps or better.

Image Setting: Rotate Mode, saturation, brightness, contrast,

14 sharpness adjustable through client software or web browser

15 Profile Management: User configuration import, export

16 Security: User Authentication, Water Marking.

Onboard Storage: Camera should support built-in Micro

SD/SDHC/SDXC Card slot upto 512 GB. It should be supplied

with minimum 128GB memory Card.

Recording Management: Format SD, overwrite, storage

management, video to NAS device.

19 Edge Analytics : Tripwire, Intrusion, Motion Detection.

Alarm Trigger : Motion/tampering detection; network

20 disconnection detection; IP conflict detection; memory card

state detection; memory space detection

21 Alarm Support: It should have 1/1 Alarm In/ Out Port.

Audio Support: It should have 1x Built-In Mic and 1/1 Audio In/

Out Port for external Mic. and Speaker (As per site requirement)

22 with G.711U/A/ G.711Mu/ AAC/ G.726 audio compression.