REPAIR TO BLDGS AND PERIODICAL SERVICES IN VARIOUS UNITS AT MENDHAR IN AOR OF AGE B/R-I AND REPAIR/ REPLACEMENT TO E/M INTERNAL FITTINGS/ FIXTURES AND WIRING IN VARIOUS UNITS AT BG, HAMIRPUR, JWG AND MENDHAR UNDER GE 881 EWS

Amount

B&R PORTION:- Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in flooring by maintaining requires gradient/undulation, finished even & fair without using extra cement, complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6 Type C-2 (using 40mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 sqm each) as in plinth protection, finished the surfaces even & fair, including filled the joints with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.

Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.11Sqm but n exc. 0.18Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.11Sqm but n exc. 0.18Sqm in vertical surfaces as skirting/dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 10mm thick screed bed in CM (1:4), complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.18Sqm but n exc. 0.38Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for Vitrified ceramic tiles 10mm thick (square/ rectangular), dark shade, polished, area of each tile not exceeding 0.36 sqms et and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed by Engr-In-Charge.

M&L for glazed ceramic coloured tiles (350x250mm)/ (450x350mm) x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick back coat layer in cement mortar 1:4, complete all as specified and directed by Engr-In-Charge.

Taking down cement plaster of any description on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc. complete all as specified and directed.

M&L for rendering 15mm thick on other than fair faces of brick or stone masonry wall surfaces in cement mortar 1:4 with mixing of liquid water proofing admixture @ 200 ml/kg of cement and finished the surface even and smooth without using extra cement, complete all as specified and directed. Note: WPC shall be measured and paid separately

M&L for 15mm thick rendering in CM 1:6 on other than fair faces of brick or stone masonry wall surfaces & finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 10mm thick rendering in CM 1:4 on fair faces of brick or concrete surfaces & finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 5 mm thick rendering in CM 1:3 on other than fair faces of brick or concrete surfaces of ceiling & finishing the surface even and smooth without using extra cement, complete all as specified and directed.

Supply only liquid water proofing admixture complete all as specified and directed.

M&L for preparation of newly plastered / unplastered surfaces of wall including cornices pilaster etc, and applying two coats of cement base paint over a coat of white wash complete all as specified and directed.

M&L for preparation of new plastered / unplastered surface of wall including cornices pilaster etc, and applying two coats of oil bound distemper over and including 1 mm thick wall care putty, complete all as specified and directed.

M&L for applying three coats of white wash including preparation of newly plastered surfaces of ceiling complete all as specified and directed.

M&L for preparation of old plastered surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M&L for complete removal of existing treatement from wall plaster and applying two coats of oil bound distemper white or any tint, over and including 1 mm thick wall care putty, complete all as specified and directed.

M&L for preparation of old plastered/unplastered surface and applying one coat of oil bound distemper white or any tint, complete all as specified and directed.

M&L for preparation of old plastered/ un-plastered wall surfaces including brooming down or steel wire brushing, scraping down, smoke soot, mould, moss, efflorescent salts, trading oil and greasy spots, and applying one coat of cement base paint, complete all as specified and directed.

Taking down shutters of any description not exceeding 1sqm each and refixing in same opening after easing and adjusting and also refixing builder's hardware as required including replacement of unserviceable screws, complete all as specified and directed.

Taking down shutters of any description exceeding 1sqm but not exc 2 Sqm each and refixing in same opening after easing and adjusting and also refixing builder's hardware as required including replacement of unserviceable screws, complete all as specified and directed.

Taking down shutters of any description area exceeding 1sqm but not exc 2 sqm, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5 Sqm and not exceeding 4 Sqm each, complete all as specified and directed.

S&F factory made pressed steel frames of size 125x60mm made out of PBI sheet 1.25 mm thick for doors with one or more rebates including necessary fixing lugs, hinge,lock strike plate etc. with one shop coat of primer complete all as specified and directed.

S&F 35mm thick 2nd class hard wood plain, framed, panelled door shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of 12mm thick veneered particle board medium density, wood particle board with commercial face veneers, complete all as specified and directed.

S&F 35mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of pink primer, complete all as specified and directed.

M&L for preparation of old painted wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint of Ist quality, complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aparture 1.18 mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aparture 1.18 mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) area not exceeding 1.5 Sqm , complete all as specified and directed.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, fixing in opening as per specification & drawing complete all as specified and directed.

S&F factory made solid core PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC sheet, 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified & shown in relevant drawing of item No. 08080 in MES Schedule (Part-II) complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden / steel frames or stone/ concrete, glazed with putty or fixed with beads, complete all as specified and directed.

S&F Sheet glass ordinary quality, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified and directed.

S&F mild steel butt hinges, medium weight, cold rolled,100mm long, complete all as specified and directed.

S&F aluminium anodised, barrel tower bolts of extruded section of size 150mm complete all as specified and directed.

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section of cast aluminium alloy complete all as specified and directed.

S&F aluminium alloy handles, cast type, anodised of size 150mm and fixed, complete all as specified and directed.

S&F 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Taking up or down steel tubing of 15 mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

Refixing old steel water tubing of 15/20 mm bore and connections in new or old position fixed to walls, ceilings and floors etc. including fittings as requiered, complete all as specified.

S&F GI tubing of 15 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified and directed.

Taking up or down steel tubing of 20 mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

S&F GI tubing of 20 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified and directed.

S&F in repair 15mm bore gun metal globe or gate valve (ISI marked) with iron wheel head,screwed both ends for iron pipe complete all as specified and directed.

S&F in repair bib tap 15 mm bore with flange, Brass CP, with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair stop valves/cock cast copper alloy 15 mm dia, chromium plated with wall flange screwed down, high pressure, with capstan handle screwed both ends for iron pipes or for unions complete all as specified and directed. Make-Jaquar Cat Part No:-CON-059KN or Equaivalent cat part of make as specified in P.S.

S&F in repair brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F in repair PVC valve less symphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC. flush pipe for low level cistern including all joints complete all as specified and directed. Make:- Prayag cat part No 501 or Equaivalent cat part of make as specified in P.S.

S&F in repair vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, snow white, with 'P' or 's' trap, front or back inlet and integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe and syphonage pipe etc. including lime concrete bedding, complete all as specified and directed. Make:- Prayag cat part No4054 or Equaivalent cat part of make as specified in P.S.

S&F in repair PVC connection 15mm size with PTMT nuts on both ends of length 600mm complete all as specified and directed.

S&F in repair vitreous china wash hand basin, white, flat back, size 550x400 mm excluding taps, waste, chain & plug and porcelain stopper but exclusive of fixing of supply and waste pipe including cutting for and pinning in ends of brackets or erecting stand etc complete all as specified and directed.

S&F in repair 15mm bore pillar tap cast copper alloy with capstan head, fancy type, chromium plated, screwed down, high pressure, with or without lettered 'Hot or Cold' with long screwed for iron pipe complete all as specified and directed. Make:- Jaquar cat part NoCON-011KN or equivalent cat part of make as specified in P.S.

S&F in repair PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint, laid in floor/walls as soil pipe including clamps, complete all as specified and directed.

S&F in repair PVC (SWR) floor trap of 75mm dia of outlet, plain with grating including jointing to waste pipe with solvent cement fixed, complete all as specified.

S&F in repair PVC soil waste and vent pipe 75 mm dia any length single socketed with rubber ring joint, laid in floor/walls as soil pipe including clamps, complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 500 Ltrs incl with 15mm ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule , including dismantling existing water tank and removing from site complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 1000 Ltrs incl with 20mm ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule, including dismantling existing water tank and removing from site complete all as specified and directed.

S&F in repair 15mm bore ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and directed.

S&F in repair stainless steel sink 1mm thick for kitchen or laboratory wih plugs, washers and wastes including fixing bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mmx420mm bowl size 410mmx330mmx160mm fixed, complete all as specified & directed.

S&F in repair anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F in repair anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed.

S&F in repair anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21, 100mm long (2 No.) suitable handle (1 no.) complete all as specified & directed.

S&F in repair 100mm long mortice lock, vertical type with 4 lever complete all as specified and directed.

S&F sheet glass ordinary quality, 5.5mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane, complete all as specified and directed.

M&L in repair for 9mm thick both sides prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination, fixed with screws to timber frame work acomplete all as specified and directed.

S&F in repair steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and directed.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

M&L for walling of random rubble stone/boulder masonry brought upto course, well bonded, bedded and solidly hearted, built in cement mortar (1:6), complete all as specified and directed.

M&L for walling of random rubble stone/boulder masonry brought upto course, well bonded, bedded and solidly hearted, built in cement mortar (1:6), except stone complete all as specified and directed.

Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surface not exceeding 20mm to face stones (lime and sand stone) and dressing of face beds and joints, complete all as specified

M&L for brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4, complete all as specified and directed.

M&L for cement concrete (1:2:4) using 20mm graded stone aggregate as in lintels upto 1.5 metre clear span, cills, steps, siesmic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm height, copings, bed block, kneelers, apex stones, bed plates, roof kerbs round or chamfered on edges, water troughs and the like including weathering, slightly rounded or chamfered angles and throatings etc.including necessary form work complete all as specified and directed by Engineer-in-Charge.

S&F mild steel TMT bars 10 mm dia and over, cut to length, bent to shape requred, including cranking , bending spirally for columns hooking for columns hooking ends and binding with and including mild steel wire (annealed ) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F TMT bars, 5mm dia and over upto incl 10mm dia, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia as in stirrups, ccomplete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) any thickness including cover fillets complete all as specified and directed.

S&F anodised aluminium snap grid frame work for false ceiling of size 605 x 605mm complete all as specified and directed.

S&F hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

M&L for 4mm thick non asbestos fibre cement building fixed or laid/inserted to timber/GI/aluminium framework fixed in ceiling with screws complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering, complete all as specified and directed.

M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

M&L for pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, valley gutter and similar works fixed with self tapping screws complete all as specified.

M&L for 0.63 mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc with grade of zinc coating 275 as in roof covering, walls, cladding etc complete all as specified.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

M&L for rolled mild steel works as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam,tee,angle, channel or flat sections) including distance pieces, cleats etc Fe 410 W(Gde E 250), quality B complete, complete all as specified

M&L for applying two coats of synthetic enamel paint of Ist quality over a coat of red oxide primer to new or previously untreated steel surfaces over 10cm width or girth including preparation of surfaces, complete all as specified and as directed.

Writing letters or figures (Block, Roman, Italic or Indian) n. exc 30cm high with synthetic enamel paint including oblitering old writing of any description to match existing work, complete all as specified and directed.

M&L for 20mm thick granite (of approved type colour) work (table rubbed & polished) in jambs, pillars, window cills, cooking plateform laid over and including 15mm thick cement screed (1:4) and jointed with grey cement slurry and pointed with white cement (1:2) with admixture of pigment to match the colour of granite stone including cutting and and moulding the edges, corners etc complete all as specified.

M&L for preparation of old painted surfaces of CGI/PGI sheet roofing and applying one coat of synthetic enamel paint in camouflage pattern/single shade, complete all as specified and directed.

S&F in repairs 15 mm dia CP brass mixer for mixing hot and cold water screwed down for iron pipe complete all as specified and directed. Make: Jaguar Cat No ARI-CHR-39051B or equivalent of Make as specified in PS.

S&F in repair vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolt, flushing cistern and flushing pipe) complete all as specified and directed.

S&F in repairs PVC (EWC) seat cover white colour with flat bottom including CP hinges complete all as specified and directed.

S&F in repair vitreous china urinals, bowl type of size 465x355x265mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern and waste pipe),complete including poviding and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing with automatic flushing cistern with brackets, flush pipe, waste pipe grating and union for discharge pipe complete all as specified and directed.

S&F in repairs flush pipe of polyethylene of low or high density or PVC 32 mm dia for low level flushing cistern/urinal/WHB complete all as specified and directed.

M&L for preparation of old plastered/ un-plastered wall surfaces including brooming down or steel wire brushing, scraping down, smoke soot, mould, moss, efflorescent salts, trading oil and greasy spots, and applying one coat of weather proof acrylic emulsion paint, exterior grade (100 % acrylic first quality) of approved shade as per manufacturer's instructions, complete all as specified and directed.

Petty repairs for leaking water in bib tap, pillar tap, stop cock, angle valve of any description any size by changing the washer/jumper etc complete all as specified and directed by Engr-in-Charge.

Removal of air lock/blockage of water in GI tubing 15/20mm bore incl taking down (if reqd), cleaning the pipe or fittings etc and refixing the same in position complete all as specified and directed by Engr-in-Charge.

Petty repairs to low level flushing cistern of any size/description for repair of leaking water by adjusting/replacing the washer and adjustment of lever required for making the cistern functional complete all as specified and directed by Engr-in-Charge.

S&F in repair brass CP jet spray with holder including 1.5m long PVC/Chromium plated flexible PVC pipe, necessary nut bolts and PVC washers fixed with PVC seat cover for pedestal pattern water closet, complete all as specified and directed.

S&F in repair 25 mm dia stainless steel curtain rod (16 gauge) complete all as specified and directed.

S&F in repair fancy type decorative brackets for curtain rod complete all as specified and directed.

E&M PORTION:- Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed.

Taking down carefully unsv sub main wiring including earth continuity any type/ size with surface casing/ caping/ TW batten/ PVC conduit surface or recess etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and directed.

M&L for point wiring with two single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable and one single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable as earth continuity to common earth and connecting to earth dolly running in and including PVC casing & caping (ISI marked) of suitable size with PVC boards of appropriate sizes and all requisite accessories such as PVC elbow, Tee, collars, bends etc. with PVC terminals box & cover for mounting swtches, sockets, fan regulator etc for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following :-

One light/fan point controlled by one way switch 6 Amp complete all as specified and directed.

One ligh point controlled by two numbers, two way switch 6 Amp complete all as specified and directed.

One 3/5 pin socket outlet 6 amp on same board complete all as specified and directed.

One 3/5 pin socket outlet 6 amp independent board complete all as specified and directed.

One bell point controlled by one way switch 6 Amp complete all as specified and directed.

All as per srl item No 110 here in before but for one 3 pin socket outlet 16/20 Amp independent with two single core 2.5 Sqmm size cable as phase & neutral and one single core 2.5 Sqmm as in continuous earth wire complete all as specified and directed.

S&F ceiling rose, 3 terminal, surface bakelite 65 mm x 50mm, PVC/poly carbonate, insulated body, complete all as specified and directed.

S&F switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified and directed.

S&F switch piano flush type 6 Amp two way, (ISI marked), complete all as specified and directed.

S&F switch piano bell push flush type 5 Amp single pole one way (ISI marked) complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin, 6 Amp flush type universal, complete all as specified and directed.

S&F Switch socket combination, 5 pin, 5 Amp flush type universal, complete all as specified and directed.

S&F Switch socket multipurpose combination 2 in 1, 5 pin, 5 and 15 Amp flush type universal, complete all as specified and directed.

S&F Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed.

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. for 1200 / 1400mm sweep, complete all as specified and directed.

S&F electric bell ding dong type 230 volts AC supply 50 Hz complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair decorative LED tube light fittings, suitable for and incl retrofit LED tube 20 watt incl LED tube light connecting up with with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing in repair inverter LED batten 1x 20W, with square profile and polycarbonate channel, lithium iron battery with charging time of 8 to 10 hours and backup tile upto 04 hours with driver, holder incl LED tube light connecting up with with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make : Havells cat part No. LHEXACP7FN1W020 or equivalent make as specified in PS

S & F in repair inverter LED bulb 9 watt including all connected items complete. all as specified and directed. Make :- Havells (Cat Part No. LHLDEGEDML8C009) or equivalent. Make as specified in ps.

S & F in repair surface mounted square/round type LED light fittings 18 watt connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing in repair LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

S&F in repair gate light fittings, outdoor type, high power , 25 watt, IP65 luminaire, prewired with suitable pole for mounting complete all as specified and directed. Make: Havells cat part No. RUBYPT25WLED830SSYMTOPC IP65 or equivalent make as mentioned in PS

Supply and fixing in repair LED street light fitting 30 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver including suitable bracket fixed to wall/ pole complete with IP 65/66 protection complete all as specified and directed.

S&F in repair LED driver suitable for 34 watt LED ceiiling light fittings and making connection to fitting complete all as specified and directed. Make:-Havells cat part No-LEDDRIVER36V36WS or Equivalent cat part of make as specified in Appx 'A' to P.S.

S&F in repair single pole and neutral enclosure with a two pin and metal earth plug and socket complete with & incl one single pole MCB of 20 Amps complete all as specified and directed.

S&F in repair sheet metal enclosure for DBs, vertical TPN double door (IP43), 4 ways built in bus bars suitable for 415 volts, AC, 50 Hz and suitable for FP MCCB as incommer and out going SP/TP MCBs complete all as specified and directed. Note:- MCBs shall be measured and paid separately.

S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 4 ways built in bus bars suitable for 240 volts, AC, 50 Hz , including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed.

S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 8 ways with 200 amps rated bus bar suitable for 240 volts, AC, 50 Hz, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed.

S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 12 ways with 200 amps rated bus bar suitable for 240 volts, AC, 50 Hz, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed.

S&F in repair MCB TPN 40-63 amps 415 volts 10 KA 'C' series, complete all as specified and directed. Make:-Havells cat part No- DHMGCTNF040 - DHMGCTNF063 or Equivalent cat part of make as specified in P.S.

S&F in repair MCB SPN 40-63 amps 415 volts 10 KA 'C' series, complete all as specified and directed. Make:-Havells cat part No- DHMGCSNF040 - DHMGCSNF063 or Equivalent cat part of make as specified in P.S.

S&F in repair MCB single pole 6 to 32 amps 240 volts 10 KA 'C' series complete all as specified and directed. Make:-Havells cat part No-DHMGCSPF006-032 or Equivalent cat part of make as specified in P.S.

Taking out old unsv exhaust fan from site and replacement of exhaust fan made up of sturdy engineering plastic complete with louvers shutter, voltage 230 V, 50 Hz, 1200 RPM, copper winding of sweep 300mm incl all connecting accessories complete all as specified and directed by Engineer-in-charge.

S&F in repair PVC conduit non metallic rigid of size 25 mm dia (external) incl all fixing accessories and fixing of conduit to wall and ceiling etc complete all as specified and directed.

S&F in repair PVC casing caping of size 25 mm incl all fixing accessories complete all as specified and directed.

S&F in repair flexible PVC conduit of approved quality of size 25 mm dia bore incl all fixing accessories complete all as specified and directed.

S&F Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron wire 4.0mm dia by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI light grade water pipe 20mm dia with funnel all as shown in electric plate No. 3 of 2009 SSR Pt-I and testing complete including earth work in any type of soil, PCC 1:2:4 type B-1 as in earthing pit and cover 50mm thick reinforced with 6mm dia MS round bar @ 10cm C/C both way and MS frame, common salt, charcoal and testing on completion including dismantling unsv earthing, complete all as specified and directed.

S&F Sub main wiring with single core cable 2x 6 Sqmm FRLS insulated unsheathed stranded copper conductor cable 1100 Volts grade including surface PVC casing caping medium grade alongwith 1x 6 Sqmm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly, complete all as specified and directed. Note:-Three wire of 6 sqmm and one run of PVC conduit/casing caping shall be measured as one unit.

S&F Sub main wiring with single core cable 2x 4 Sqmm FRLS insulated unsheathed stranded copper conductor cable 1100 Volts grade including surface PVC casing caping medium grade alongwith 1x 4 Sqmm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly, complete all as specified and directed. Note:-Three wire of 4 Sqmm and one run of pvc conduit/casing caping shall be measured as one unit.

S&F 1100 volts grade heavy duty cable PVC insulated solid aluminium conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 m apart including 4mm dia GI suspension wire, one twin core cable flat or circular of size 6 Sqmm 2 core & including taking down old old unsv service cable connection, complete all as specified and directed.

S&F 1100 volts grade heavy duty cable PVC insulated solid aluminium conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 m apart including 4mm dia GI suspension wire, one twin core cable flat of circular of size 10 Sqmm 2 core including taking down existing old service connection, complete all as specified and directed.

Repair and maintenance of unserviceable ceiling fan of 1200mm/1400mm sweep at contractor's work shop, incl dismantling complete the ceiling fan parts, inspecting serviceability of all the parts, refixing of serviceable parts after cleaning and replacement of unserviceable parts with company's genuine parts i.e. capacitor, bearing, bushes, shaft, bracket, rubber bush, connecting wire, PVC connector, aluminium clamp for rod, bracket, bush rod, greasing/oiling etc assembling, cleaning and testing of ceiling fan complete all as specified and directed. Note: (i) Unserviceable parts as above shall be measured and paid separately under relevant items of Sch 'A' item No 131 to 136 as supply only. (ii) Rewinding of stator will be measured & paid for separately under relevant item of Sch 'A'. (iii) Cost of minor part i.e. Cotter pin, screws shall be deemed to included in the cost of quoted rate.

Supply only bearing good quality for ceiling fan 1200mm/1400mm sweep ISI marked complete all as specified and directed.

Supply only Gun metal bush for ceiling fan 1200mm/1400mm sweep complete all as specified and directed.

Supply only capacitor 2.5 mfd ISI marked complete all as specified and directed.

Supply only brass bracket assy for hanging the ceiling fan 1200mm/1400mm sweep complete all as specified and directed.

Supply only 3 core flexible wire 40/.0076, white colour from ceiling rose to fan connector complete all as specified and directed.

Supply only stator shaft for ceiling fan complete all as specified and directed.

Supply only fan blade for ceiling fan 1200 mm sweep all as per existing make complete all as specified and directed.

Supply only fan blade for ceiling fan 1400 mm sweep all as per existing make complete all as specified and directed.

Supply only canopy (top/bottom) of ceiling fan 1400 mm sweep all as per existing make complete all as specified and directed.

M&L for removing of old burnt winding of ceiling fan any size , type and rewinding of stator winding with superior quality copper wire with insulation complete all as specified and directed.

M&L for painting to ceiling fans complete on site with one coat of synthetic enamel paint by spraying including filling cavities with filler after cleaning all dust etc complete all as specified and directed.

S&F in replacement of down rod of ceiling fan with down rod of 15 mm bore medium grade GI pipe 0.45 metre long with clamps, bolts, nuts, split pins washers of suitable size of approved quality etc complete all as specified and directed.

S&F in replacement of down rod of ceiling fan with down rod of 15 mm bore medium grade GI pipe 0.60 metre long with clamps, bolts, nuts, split pins washers of suitable size of approved quality etc complete all as specified and directed.

Repair and maintenance of unserviceable exhaust fan of any cap and sweep by dismantling the exhaust fan parts, inspecting the serviceability of parts, refixing of serviceable parts after cleaning, replacement of unerviceable parts i.e. beaing, bush, capacitor, connecting wires, fan blade, locknut, rubber pad etc, oiling/greasing, cleaning and testing of exhaust fan complete all as specified and directed. Note: (i) Unserviceable parts replaced shall be measured and paid separately under relevant items of Sch 'A' item No 140 to 141 & 144 as supply only. (ii) Rewinding of stator winding shall be measured & paid for separately under relevant item of Sch 'A'. (iii) Cost of minor part i.e. screws shall be deemed to included in the cost of quoted rate.

Supply only double ball bearing (ISI marked) for exhaust fan of 200 mm sweep to 450 mm sweep fan complete all as specified and directed.

Supply only gun metal bush for Exhaust fan of any capacity. complete all as specified and directed.

M&L for rewinding of 450mm sweep exhaust fan motor with superior quality copper winding wire with insulation complete all as specified and directed.

M&L for rewinding of 300mm sweep exhaust fan motor with superior quality copper winding wire with insulation complete all as specified and directed.

Supply only blade of exhuast fan of 200 mm sweep to 450 mm sweep as per existing make complete all as specified and directed.

M&L Preparation of painted surfaces of exhaust fan of any make and size by scrubbing old surfaces and applying one coat of synthetic enamel paint by spray painting complete all as specified and directed.

M&L for Disconnecting electric & water connection to geyser of capacity 25/35/50 litr, taking down from existing position, dismantling and inspecting all the parts for its serviciability, cleaning of serviceable parts i.e. base assembly, connecting lead, thermostat, electric contact, electric wiring, indicators, safety valves etc re-fixing in the same in position, testing complete all as specified and directed by Engr-in-Charge. Notes: (i) The defective parts to be replaced shall be measured and paid separately under relevant item No. 57 to 69 of Sch 'A' as supply only (ii) Cost of minor items i.e. screws, nuts, bolts etc shall be deemed to be included in this item

Supply only heating element of capacity 2 KW, ISI marked suitable for existing size, type & make of geyser complete all as specified and as directed.

Supply only heating element of capacity 1.5 KW, ISI marked suitable for existing size, type & make of geyser complete all as specified and as directed.

Supply only thermostat, ISI marked suitable for existing size, type & make of geyser complete all as specified and as directed.

Supply only indicator lamp suitable for existing size, type & make of geyser complete all as specified and as directed.

Supply only geyser safety valve suitable for existing size, type & make of geyser complete all as specified and as directed.

Supply only PVC pipe connection of heavy duty for inlet, outlet connection suitable to withstand the pressure and temperature complete all as specified and as directed.

Supply only aluminium/chromium type flexible connection, heavy duty for inlet, outlet connection suitable to withstand the pressure and temperature complete all as specified and as directed.

Supply only inner tank made out of steel sheet conforming to IS, suitable for 25 litres capacity of geyser, vertical type complete all as specified and as directed.

Supply only inner tank made out of steel sheet conforming to IS, suitable for 35/50 litres capacity of geyser, vertical type complete all as specified and as directed.

Supply and fixing in replacement of non return valve made out of brass fixed in vertical complete all as specified and as directed.

Supply only new base assembly with inlet and outlet pipe made out of steel sheet with gasket and proper size of nuts, bolts and washer etc suitable for 25 litres capacity of geyser complete all as specified and as directed.

Supply only new base assembly with inlet and outlet pipe made out of steel sheet with gasket and proper size of nuts, bolts and washer etc suitable for 35/50 litres capacity of geyser complete all as specified and as directed.

VIKAS ENTERPRISES

NATIONAL TRADING COMPANY

M/S BHATT TRADERS