PROVN OF COVERED SHED TO EXISTING HARDSTANDING FOR 12 X LT VEHICLES PARKING NEAR MT GARAGE, COVERED SHED FOR B VEHICLES OF ASC BN AND OTHER SANCTIONED WORKS IN THE AREA OF AGE B/R-I UNDER GE PANAGARH

Amount

Excavating in trenches, n.exc 1.5 m wide and n.exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10 sqm on plan and getting out as in soft/loose soils complete all as specified and directed.

M&L for moorum/red bajri filling in floors or pavings, laid in layers n.exc. 15 cm thick spread, levelled and rammed including watering complete all as specified and directed.

M&L for cement concrete (1:4:8) Type D2 (using 40 mm graded stone aggregates) as in foundations, filling and mass-concrete complete all as specified and directed.

M&L for PCC (1:2:4) 100 mm thick Type B2 (using 40 mm graded stone aggregate) used as in sub base floor/pavings and finishing cement concrete surface without using extra cement complete all as specified and directed.

M&L for sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigments complete all as specified and directed.

M&L for brickwork with flyash bricks, straight or curved on plan exc 6m mean radius, built in CM (1:4) complete all as specified and directed

M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surfaces of wall, surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for PCC (1:2:4) Type B0 (using 12.50 mm graded stone aggregate) used as in copings complete all as specified and directed.

M&L for fixing PVC (SWR) pipes of 110 mm bore diameter single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

Removing excavated spoil to a distance n.exc.50m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 cm as in soft/loose soil complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No 13.00 mentioned here-in-above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for flat rough finished surfaces of concrete complete all as specified and directed.

M &L for RCC (design mix) M-25 (using 20 mm graded stone aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment using Fe 410 -W (Gde E- 250) quality A complete all as specified and directed.

M&L for preparation of painting of new steel surfaces over 10 cm in width or girth over a coat of primer using red oxide and applying two coats of synthetic enamel paint complete all as specified and directed.

S&F pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based Plain steel as in ridges sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

Excavating over areas, n.exc 1.5 m deep and getting out soft/loose soil complete all as specified and directed.

Brickwork with fly ash old sized bricks, straight or curved on plan exc 6 m mean radius, built in CM (1:6) complete all as specified and directed.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM (1:6) and finishing fair even and smooth without using extra cement complete all as specified and directed.

M&L for hardcore using broken stone or boulders of gauge n.exc. 63 mm, deposited, spread and levelled in layers n.exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 100 mm thick cement concrete 1:4:8 type C2 (using 40 mm graded stone aggregates) as in sub base of floor complete all as specified and directed.

M&L for 100 mm thick cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) fair finished even and smooth with using extra cement complete all as specified and directed.

M&L for 75 mm thick cement concrete type C-1, 1:3:6 (using 20mm graded stone aggregate) as in plinth protection finished even and smooth without using extra cement complete all as specified and directed.

Forming Construction joint 30mm deep x 10mm wide filled with sealing compound grade A complete all as specified and directed.

M&L for formwork for rough finished surface of concrete (flat surface) to sides of pillars, posts, struts, piers, columns, and stanchions complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for fair finished surfaces of concrete complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work for rough finished surface, n.exc 200m thick (Horizontal or sloping) complete all as specified and directed.

M&L for reinforced cement concrete (Design Mix) M-25 (using 20mm graded stone aggregate) in columns, pillars, piers, etc complete all as specified and directed.

M&L for reinforced cement concrete (Design Mix) M-25 (using 20mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for reinforced cement concrete (Design Mix) M-25 (using 20mm graded stone aggregate) in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Supply only Integral water proofing compound complete all as specified and directed.

S&F powder coated anodised aluminium frames for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified and directed

S&F powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No). hinges type B-21 100mm long (2 no.) suitable handle (1 No) complete all as specified and directed.

S&F anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in- charge.

S&F 5.5 mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane complete all as specified and directed.

M&L for prelaminated particle board 18/19 mm thick, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to aluminium frame work complete all as specified and directed.

M&L for rendering 15 mm thick cement plaster in CM (1:4) on external fair faces of brick/concrete work surfaces finished even and smooth (without using extra cement) incl WPC complete all as specified and directed (Note: WPC will be measured and paid separately).

M&L for rendering 5 mm thick in CM (1:3) on fair faces of brick work or concrete wall surfaces & finishing the surfaces fair and even on ceiling complete all as specified and directed.

M&L for new plastered surfaces of wall & applying two or more coats of 100% premium acrylic emulsion (Exterior Weather Coat) paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004 , alkali & fungal resistance, dirt resistance exterior paint of required shade (Company depot tinted) with silicon additives@ 1.43 litre/10sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over old surfaces complete all as specified and directed. (Make: M/s Apex Ultima of Asian/ Weather Coat all guard of Berger/Xtra Tough of Shalimar)

M&L for preparation new plastered surfaces and applying three coat of white washing on ceiling complete all as specified and directed

M&L for cement concrete type C-2, 1:3:6 (using 40 mm graded stone aggregate) 100 mm thick as in sub base of floor for receiving floor finishes complete all as specified and directed.

M&L for cement concrete reinforced type B-1, 1:2:4 (using 20 mm graded stone aggregate) 25 mm thick as in floor for receiving screed bed for floor finishes complete all as specified and directed.

M&L for acid resistant tiles 15mm thick vitreous ceramic, unglazed, set, jointed and pointed in chemical resistant mortar, resin type, in floors complete all as specified and directed.

Excavating in trenches, n.exc 1.5 m wide and n.exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10 sqm on plan and n.exc 1.5 m in depth and getting out in hard /dense soil complete all as specified and directed.

Demolition of Cement Concrete (unreinforced) in ground floors and pavings exc 15 cm thickness (below or above ground level) and removing rubbish off from the premise complete all as specified and directed.

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in hard/dense soil complete all as specified and directed

M&L for cement concrete 1:3:6, Type D-2 (using 40 mm graded stone aggregates) in foundations etc complete all as specified and directed.

Excavation in post holes n.exc 0.50 cum, getting out, returning filling in and ramming earth, watering and removing surplus soil n.exc 50 m in soft/loose soil complete all as specified and directed

M&L for chequered cement tiles 300X300x25mm thick set and jointed and pointed in neat cement slurry with gray cement and pigment and over and including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and directed

S&F 2nd class clean sawn hard-wood as in scantlings complete all as specified and directed.

M&L for preparation of newly plastered surfaces and three coats of white washing on wall of brickwork complete all as specified and directed.

S&F hangers 6 mm dia. GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed

S&F anodised aluminium snap grid (605X605mm ) frame work for false ceiling with all necessary aluminium angle & Tee arrangement with and incl fixing cleats complete all as specified in SSR and directed by the Engr-in-charge.

S&F non asbestos fibre cement design building boards 6 mm thick fixed or laid/ inserted to timber/GI/Aluminium framework with screws complete all as specified and directed. (Note : Pattern and design shall be approved by GE)

M&L for point wiring for light point/ fan point, one light/fan/exhaust fan point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including pressed steel terminal switch boxes, 3 mm thick bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers and 1.5 sqmm nominal cross sectioanl area multistranded copper conductor FRLSH PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed. (Note: Quoted rate deemed to be included for necessary chasing/cutting and making good the surface)

M&L for wiring for 5 Amps socket out let on independent Boards controlled by one, one way switch using 2.5 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes, 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 2.5 sqmm nominal cross sectioanl area multistranded copper conductor, PVC insulated unsheathed FRLSH cable earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified. (Note: Quoted rate deemed to be included for necessary chasing/cutting and making good the surface)

M&L for wiring for 15 Amps socket out let on independent Boards controlled by one, one way switch using 4.0 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes, 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 4.0 sqmm nominal cross sectioanl area multistranded copper conductor, PVC insulated unsheathed FRLSH cable earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified. (Note: Quoted rate deemed to be included for necessary chasing/cutting and making good the surface)

S&F switch piano flush type, single pole , 5/6 Amps, one way complete all as specified and directed.

S&F switch socket combination, 2 in 1 multipurpose 5 pin , (5/6 Amps) complete all as specified and directed.

S&F switch socket combination, 5/16 Amps 5 in 1 flush type controlled by one switch complete all as specified and directed

S&F ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified and directed.

S&F 01x 18 W LED batten light fittings, with T-8 tube, lighting fixture complete with all accessories and connection from ceiling rose with twin core twisted flexible copper conductor cable with suitable size and earthing complete all as specified and directed

S&F security light fittings 25 watts, minimumm lumen output 100 lumen/ watt, made up of pressure dia cast housing with prismatic polycarbornate diffuser and individual LED with secondary optic and IP65 including necessary connection complete suitable for pole dia 25mm complete with all accessories including connected with twin core twisted flexible copper conductor of suitable size complete all as specified and directed. (Make - Bajaj/Crompton/Phillips)

S&F lamp holder, PVC/polycarbonate type with back plate straight or angular suitable for batten fittings complete all as specified and directed

S&F exhaust ventilation fan of sweep 300mm, steel body with louvers, 240 volts, BEE 5 star rated, steel body, ISI marked complete all as directed by Engr-in-Charge.

S&F epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), Single pole and neutral 240 V, 8 ways with mounting fitted with bus bar, DIN channel, neutral link and incoming contact complete all as specified and directed.

S&F MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Voltsand to be housed in DBs including necessry connection complete all as specified and directed. (Note : Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

S&F MCB SP, 40 to 63 Amps, 'C' series 10kA, 240 Voltsand to be housed in DBs including necessary connection complete all as specified and directed. (Note : Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

S&F MCB SPN 63 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessary connection all as specified and directed. (Note : Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating).

S&F XLPE armoured cable 35 sqmm 4 core,1100 volts grade heavy duty cable,ISI marked passing through pipe, with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed complete all as specified.

S&F XLPE armoured cable 10 sqmm 2 core,1100 volts grade heavy duty cable,ISI marked passing through pipe, with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed complete all as specified.

Excavation in trenches n.exc 1.5m wide and n.exc. 1.5m depth and getting out in hard/dense soil complete all as specified and directed.

Returning, filling, including spreading, levelling, watering and well ramming in layers n.exc. 25cmin soft/loose soil complete all as specified and directed.

Removal of excavated soil to a distance n.exc 50 m and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as directed.

Supply and lay for dry river sand filling for cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified and directed. (Note : Punned thickness shall be measured).

M&L for sub class B bricks locally available of size 25 x 12.5 x 7.5 cm laid dry width wise across the line of cable in trenches for protection of UG cable complete all as specified and directed.

M&L for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth wire electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth wire encased in and including 15 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments, 20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion. (Note :- (i) If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department. (ii) Testing to be carried out by the contractor in presence of Engr- in- Charge , entered in the earth testing register, prepared and to be maintained by the contractor & submited to concerned JE E/M. (iii) T&P and testing instrument(Meger) to be provided by the contractor at own cost).

subash chander bahl

MS ROYAL CONSTRUCTION INDEX NO 158 2010 BKP

M/S S M ENTERPRISE

SUPARNA TRADING

Hooghly Construction Co.

M/S TRIVENI BUILDERS