03/2020-21/EE/TCAG

Amount

Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

1:5:10 (1 cement : 5 fine sand derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:

Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

25mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws.

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets :

20 mm dia (heavy type)

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :

Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete.

250 mm weighing not less than 150 gms.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Single rubber stopper

Providing and fixing to existing door frames.

30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of ‘H’ section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. ‘U’ cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-in-charge.

Taking out damaged W.C. pan, urinal, wash basin with C.C. including cleaning of all area by sweeping with phenol, acid and disposal of un-serviceable material within 50 M lead.

Providing and fixing galvanised wire mesh of average width of aperture 1.40 mm and nominal diameter of wire 0.63 mm in wooden/steel door and windows including wooden fillets/MS flats with nails or nut & bolts etc. complete wherever required and as per direction of the Engineer-in-charge.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Arranging welding machine for welding of Broken steel componants such as Handels, fastners, hinges, grills, etc.as and where required as per the direction of Engineer-in-Charge. (rate includes labour & transportation of machine at site).

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,

(i)Single socketed pipes.

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion.

110 mm bend

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hardwood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

12mm Cement Plaster of mix:

1:6 (1 cement: 6 coarse sand)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work.

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.

Two coats.

White washing with lime to give an even shade :

Old work (Two or more coats) .

Old work (one or more coats) .

Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade :

Old work (one or more coats)

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

One or more coats on old work.

French spirit polishing :

One or more coats on old work.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground , all complete as per directions of Engineer-In-Charge.

With cement mortar 1:4 (1 cement : 4 fine sand).

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty:

Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm).

Re-lettering with black Japan paint of approved brand and manufacture.

Repairs to wooden door or window shutter for smooth closing and opening including necessary chiseling to frame or applying plane on edge of shutter all complete (area upto 2.00 Sqm)

Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineerin-Charge.

(a) Internal Work- Exposed on wall

Providing & fixing White vitreous china water closet squatting pan (Indian type) along with "S" or "P" trap including dismantling of old WC seat and "S" or "P" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge.

a) Orissa pattern W.C Pan of size 580x440 mm

Repairing of Aluminium doors and windows size upto 3 sqm at site by dismembering the members and refixing members with cleats etc. as required for smooth functioning etc as directed by Engineer-in-charge. Any material required for repairing such as cleats and screws and pivots shall be arranged by agency.

Cleaning of drainage manholes and sewer lines by removing the deposited and other rubbish from the manholes and cleaning the sewer lines by rodding and flushing with water as directed by the Engineer -in- charge. (Rate per One manhole and sewer line to next manhole)

Attending repairs to Low level PVC flush tanks by replacing necessary parts as per requirement as directed.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge..

In cement mortar

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead:

Of area 3 sq. metres and below

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge :

15 mm to 40 mm nominal bore

Credit for:

Unserviciable GI Pipes/Fiitings

Unserviciable CI Pipes/Fittings

Unserviciable Brass Bib/stop cocks/pillar tap

Gun metal gate valve with C.I wheel 20mm dia

Gun metal gate valve with C.I wheel 25 mm dia

Gun metal gate valve with C.I wheel 40 mm dia

Brass Ball cock 20 mm nominal bore

Low level PVC flush tanks (10 litres)

Credit of old wooden door shutters of area 3 Sqm or below, recovered from dismantling of partition/door shutters.

Cutting floor of sunken portion (toilet/bath room) upto required length and width for fixing bend for w.c. pan/trap and associated soil/waste pipe and making hole in adjacent brick wall for outlet and repairing same after fixing w.c. pan/trap including cost of required c.c./plaster etc. complete as per direction of the Engineer-in-charge.

Credit of old un-serviceable materials recovered from dismantling/dimolishing from work :

(a) PVC pipe,fittings & PTMT fittings etc.

Credit of old serviceable materials recovered from dismantling/dimolishing from work :

(a) Old Bricks

Credit of old un-serviceable materials recovered from dismantling/dimolishing from work :

(a) Hydralic floor spring

Providing and fixing C.P. brass pillar tap 15mm nominal bore for wash basins as directed.

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.

10 litre capacity - White

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete :

White solid plastic seat with lid

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively.

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings :

Flat back wash basin of size 550x400 mm.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Semi rigid pipe

32 mm dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Rectangular shape 453x357 mm

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.

Waste coupling 31 mm dia of 79 mm length and 62 mm breadth weighing not less than 45 gms.

Providing and fixing 600mm long C.P. brass towel rail with C.P. brass brackets using C.P. brass screws.

Providing and fixing PVC trap of self cleansing design with top tile and strainer complete, including cost of cutting and making good the walls and floors :

100 mm inlet and 75 mm outlet

De-sludge or pumping out the septic water and Cleaning of Septic tank by revoing of sludge from septic tank or pumping out by mechanical means i/c disposal of sludge from outside the compound at authorized municipal dump or out side of the township all complete as per direction of En-in-charge.

Providing and applying cement slurry @ 0.50 Kg/sqm mixed with tapcrete @ 0.15 Kg/sqm on gola, khurras. roof etc. after cleaning the surface by brush, filling joints with cement mortar 1:2 (1 cement: 2 fine sand) mixed with tapcrete 30% by weight of cement etc. complete as per direction of the Engineer-in-charge.

Providing and fixing PVC tank lid to the overhead tank with necessary screws, nails, bolts & nuts complete etc.,as per the directions of Engineer-in-charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall

15 mm nominal outer dia. Pipes.

20 mm nominal outer dia. Pipes.

25 mm nominal outer dia. Pipes.

32 mm nominal outer dia. Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work

40 mm nominal outer dia. Pipes.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall.

15 mm dia. nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : External work

40 mm dia. nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

25 mm dia. nominal bore

Providing and fixing CPVC gate valves of approved brand and manufacture for CPVC pipe lines.

25 mm size

32 mm size

Providing and fixing uplasticised PVC connection pipe with brass unions :

45 cm length

15 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work)

15 mm nomonal bore.

20 mm nomonal bore

25 mm nomonal bore.

40 mm nomonal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Circular Tank

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931:

15 mm nominal bore.

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

15 mm nominal bore.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 :

15 mm nominal bore.

Providing and fixing PTMT bib cock of approved quality and colour.

15mm nominal bore, 86 mm long. Weighing not less than 88 gms.

Providing and fixing PTMT pillar cock of approved quality and colour .

15mm nominal bore, 107 mm long. Weighing not less than 110 gms.

Providing and fixing Stainless Steel grating 0.60mm thick grating for floor traps complete as directed.

100mm dia Circular

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.

20 mm nominal bore, 120 mm long. Weighing not less than 198 gms.

Providing and fixing PTMT angle stop cock 15 mm nominal bore. Weighing not less than 85 gms.

Fixing available G.I. pipes (Internal work) with new fittings wherever required nailing /clamps etc complete

a) 15 mm to 40 mm nominal dia

Replacement of old valve by providing and fixing Upvc Gate valve of approved quality.

20 mm nomonal bore.

25 mm nomonal bore

40 mm nomonal bore.

Arresting leakage through GI pipe by cutting and dismantaling upto length of 6.00 Metre and fixing the same includinmg providing and fixing G.I. Union , cutting and threading the pipe and making long screws, etc complete

15 mm nomonal bore.

20 mm nomonal bore

25 mm nomonal bore.

40 mm nomonal bore

Replacement of old damaged polyethelene cover for water storage tank by providing and fixing polyethelene cover for water storage tank with P.V.C. bolts and nuts and locking arrangement all complete as directed by the Engineer -in -charge.

Periodic cleaning of open drain including removel of garbage and disposal of the same to Municipal dumping ground etc complete as directed by the Engineer in charge.

Of size upto 0.30 x 0.40 Mtr

Providing and fixing abolution jet of approved quality in European type WC seat complete as per direction of the Engineer-in-charge.

Cleaning of choked water supply G.I. pipe line with pressure machine for proper supply of water i/c opening and refixing of bends, sockets etc. whichever necessary complete as per direction of the Engineer-in-charge.

Replacing brass spindle of pillar tap/bib cock etc. of approved quality in order to make the tap in good working order complete as per direction of the Engineer-in-charge.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg., for doors, including cost of cutting floors ,embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.

With stainless steel cover plate minimum 1.25 mm thickness.

Removing and Cleaning of strains dust etc., on ceramic tile flooring / glazed tile dadoing with acid and floor cleaner and grouting the joints with white cement using necessary colour pigment etc., and making good as per the directions of Engineer-In-Charge.

Cleaning of terrace / spouts / khurras / canopies / blocked chajjas and there spout pipe i/c Rain water pipe etc. by removing leaves, grass, dust, rubbish and other deposited and accumulated material etc., including disposal of rubbish to dumping ground up to a distance of 50m.

Terrace, khurras, accessible canopy and like

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all loads including all lifts involved.

Refixing old glass panes with putty and nails .

Providing anf Fixing Red sand stone over manholes and gully trap wherever required as per direction of Engineer incharge.

30 to 40mm mm thick

Cleaning of over head water storage tank 250 to 1000 litre capacity including removing of algee by using the Bleaching Powder,removing silt and all foreign material from the tank etc and after cleaning of tank finally mixing the appropriate qty of potassium permagnet into fresh water all complete as per direction of Engineer-in-Charge.

MRADUL PRATAP SINGH