Smart periodical and certain B/R repairs under GE (East) Ferozepur Cantt

Amount

Taking down cement plaster on brick walls or ceiling of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as specified.

M&L 12mm thick rendering cement plaster in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L 15mm thick rendering cement plaster in cement mortar (1:4) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick rendering cement plaster in cement mortar (1:3) on the surface of ceilings and finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new surfaces of wall and applying three coats of lime white wash complete all as specified and directed.

M&L for preparation of newly plastered surface of walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling & applying three coats of white wash complete all as specified and directed.

M&L for preparation of old surface of ceiling & applying one coat of white wash complete all as specified and directed.

M&L for preparation of old decorated surface of wall and applying one coat of cement base paint on old plastered surface of walls complete all as specified and directed.

M&L for preparation of wood or wooden based old surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint of approved shade complete all as specified and directed.

M&L for preparation of old steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for preparing of old decorated surfaces by brooming down and applying one coat of white wash on walls including cornices complete all as specified and directed.

M&L for applying two coat of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification using paint roller technology and providing 2 mm thick water proof based wall putty and sanding the surface to prepare the surface even and smooth complete all as specified and directed.

M&L for complete removal of existing wall finishes, any type by vigorously wire brushing, brooming, dusting & finally washing with water to clean the surface absolutely free from any kind of existing finishes & foreign materials, making good minor surface imperfections such as holes, dents cracks etc in cement mortar 1:3 and applying 02 mm thick water proof wall care putty on the internal surface of wall with uniform thickness incorporating water proof putty @ 2.00 kg/Sqm & making surface absolutely smooth complete all as specified and directed.

M&L for complete removal of existing wall finishes, any type by vigorously wire brushing, brooming, dusting & finally washing with water to clean the surface absolutely free from any kind of existing finishes & foreign materials, making good minor surface imperfections such as holes, dents cracks etc in CM 1:3 and applying 02 mm thick water proof wall putty on the external surface of wall with uniform thickness incorporating water proof putty @ 2.00 kg/Sqm & making surface absolutely smooth complete all as specified and directed.

M&L for applying two coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification using paint roller technology to prepare the surface even and smooth on new surface complete all as specified and directed.

M&L for preapring Old Surface applying one coat of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification using paint roller technology to prepare the surface even and smooth on new surface complete all as specified and directed.

M&L for complete removal of existing wall finishes, any type by vigorously wire brushing, brooming, dusting & finally washing with water to clean the surface absolutely free from any kind of existing finishes & applying two or more coats of textured internal paint of required shade applied @ 3.28 ltr/ 10 Sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 Sqm over 2 mm thick wall care putty over plastered surfaces to prepare the surface even and smooth complete all as specified and directed.

M&L for applying two or more coats of 100% Premium acrylic emulsion paint over completed removed putty treated surface having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm the surface even and smooth upto height 12 mtr including necessary scaffolding complete all as specified and directed NOTES FOR ITEM NO. 13 to 19:- (a) The work pertaining to smart periodical services shall be executed by authorized applicator through manufacturer of which the materials i.e ,acrylic water based exterior grade primer, acrylic emulsion Paint, Distemper, water baesd premium acrylic smooth exterior emulsion, Putty etc. is proposed to be used by the contractor and approved by GE. (b) Cost of scaffolding etc of building shall be included in the quoted rate. (c) Authorised applicator shall have valid authorisation letter from the manufacturer (Minimum regional HQs) and shall have been issued not less than 30 days from the date of commencement of the work. The authorisation letter needs to be valid for the complete period of execution of the painting work. (d) After preparation of the surface, Engr-in-Charge shall approve the same before applying primer and finishing coats through roller.. (e) The equipments to be used in the work shall be certified by the manufacturer with whom the MoU been entered into. (f) Contractor shall submit approved company generated 05 years warranty card at the time of submission of RAR & Final Bill. (g) Primer/Distemper/Texture Paint/emulsion application to be carried out through air less spray machine (Only mechanical application allowed except in paint application on bands/chajja/building edges/borders/projections where contrasting color as specified and directed is to be applied). (h) Sanding of surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer. Proper masking to be carried out before primer and paint application). (h) Quoted rate shall be inclusive of provision of adequate form work and scafolding if required upto height 12 mtr.

M&L for shotcreting average thickness 50 mm in RCC columns, beams and slab etc. with cement concrete M-25 (Design Mix). Concrete having the specified minimun characterstic compressive strength (with ordinary portland cement, coarse sand and graded stone aggregates of 6 mm maximum size in proportion as per design criteria and Hardener/ admixture) incl the cost of centering and shuttering at edges and corner etc as directed by Engineer-in-Charge incl chipping of unsound/week concrete mateial 50 mm average thickness from slabs, beams/ columns etc with mannual chiesels or standerd power driven percussion type machine incl tapering of all edges, make square shoulder of cavities incl cleaning the exposed concrete surface and reinforcement with wire brushes and throughly washing with water and allowing it to dry etc incl removal of rust by applying approved rust remover chemical and the coating with Dr Fixit Epoxy zinc primer @ 6 Sqm per Litre at DFT of 100 micron, applying the SBR Latex based bonding agent on each layer of the shootcreting work of Dr Fixit Pidicrete URP on the entire surface complete all as directed including pressure grouting with epoxy injection grout including 5 mm thick cement plaster in CM (1:3) finished even and smooth without using extra cement including removing rubbish material from building and thrown in low lying lying area at any distance upto 500 metres from the site complete as directed by Engineer-in-Charge. Make of chemical : Epoxy bonding agent, Rust remover, Anti corrosive coating, Epoxy grout, Hardener/ admixture shall be of Berger/ Sika/Fosroc/Pidilite or Techno commercial or equivalent make approved by GE. Notes : (i) Complete treatment to be executed by approved applicator (Applicator to be approved by GE). (ii) The Contractor and manufacture of shotcrete shall give the warranty before commencement and also for the strengths achieved in the post completion of work. (iii) The chemicals to be used in the work shall be certified by the manufacturer with whom the MoU been entered into. (iv) Hard drawn steel wire fabric will be measured and paid seperately (v) Design Mix to be carried out from CTL,Chandigarh and approved by GE.

S&F mild steel TMT bars as in reinforcement 6mm to 8 mm dia and over cut to length,bent to shape required including cranking, bending spirally for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Supply and fixing hard drawn steel wire fabric not exc 4 kg/sqm cut to lengths, wire mesh to be fixed and firmly anchored to the concrete surface by means of 'L' shaped mild steel shear key welded with existing reinforcement including cost of material, labour, tools and plants incl welding/L-clip/tying with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and as directed.

M&L for applying bond coat of epoxy bonding agent & cement mortor in 1:1 ratio for bonding old and new concrete on damaged surfaces applying ready mix polymer modified mortar upto 60mm thickness (Chajjas fins, border,slab, beams etc) :- (i) Including application of rust remover on exposed reinforcement and subsequent application of anticorrosive coating. Also, pressure grouting with epoxy injection after application of polymer modified mortar. (ii) Use of electrical mixer to get the homogeneous dough on bond coat surfaces. (iii) To achieve required thickness repeat this step after 24 hrs as required. (iv) Keep the surfaces moist using water forg for 5 to 7 days etc complete all as specified and as directed. (v) Rate shall be inclusive of all necessary scaffolding for building height up to 24 meters complete all as directed by Engineer-in-Charge. Make of Chemicals : - Epoxy bonding agent, Rust remover, Anti corrosive coating, Polymer modified mortar, Epoxy grout shall be of Berger, Krishna, Dr Fixit, MC Bauchemie and M/s Cemistik, Sika or Equivalent as approved by GE. Notes : (i) Complete treatment to be executed by approved applicator (Applicator to be approved by GE). (ii) The Contractor and manufacture of polymer modified mortar shall give the warranty before commencement and also for the strengths achieved in the post completion of work. (iii) The chemicals to be used in the work shall be certified by the manufacturer with whom the MOU been entered into. (iv) Hard drawn steel wire fabric will be measured and paid seperately

M/s Bansi Lal (BID ID -3334344)

AKASH ELECTRICALS (BID ID -3334400)

Karan Engineers (BID ID -3335883)

Bhupindra Traders (BID ID -3335741)

shivam builders (BID ID -3334570)

VK ENTERPRISES (BID ID -3335612)

B.L. Chaudhri and Co. (BID ID -3336015)