ADDITION ALTERATION AND SPECIAL REPAIRS TO STRUCTURES/HOUSING OF VARIOUS SUB STATION BETWEEN LION GATE AND SOUTH BREAK WATER AT NAVAL DOCKYARD MUMBAI UNDER GE NW KUNJALI

Amount

Taking down chowkats or frame with shutter (without taking off shutter from frame), not exceeding 1.5 Sqm each complete all as specified and directed by Engineer-in-Charge.

All as per item above but exceeding 1.5 Sqm but not exceeding 4 Sqm each.

Dismantling old unserviceable steel windows exceeding 1.5 Sqm each with frame, shutters etc complete all as specified and directed by Engineer-in-Charge

Dismantling old unserviceable aluminium windows exceeding 1.5 Sqm each with frame, shutters complete all as specified and directed by Engineer-in-Charge

Dismantling wall and ceiling boards (fiber, pulp, insulation, etc.) or insulation boards /slabs /blankets, any thickness, including cover fillets complete all as specified and directed by Engineer-in-Charge

Dismantling wrought iron or mild steel work of any description not otherwise specified and complete all as specified and directed by Engineer-in-Charge

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and directed by Engineer-in-Charge

Taking down eaves gutters and rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swanneck, etc. incl. cleaning or refixing or removal to store ( measured over all as fixed along the centre line over fittings and accessories) complete all as specified and directed by Engineer-in-Charge

Taking down 15mm bore, GI tubing and connections including cleaning for refixing or removal to store and complete all as specified and directed by Engineer-in-Charge

All as per item above but 20 mm bore GI Pipe.

All as per item above but 25 to 32mm bore GI Pipe.

Dismantling 100/75 mm bore, cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches if required complete all as specified and directed by Engineer-in-Charge

Demolition of brick work or stone /boulder masonry built in cement mortar, including all quoins, arches, pillars complete all as specified and directed by Engineer-in-Charge

Dismantling boarding, any description, fixed in any position with screws including frames complete all as specified and directed by Engineer-in-Charge

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick/ surfaces built in cement mortar inclu. raking out joints, bedding for key scrubbing down with water and complete all as specified and directed by Engineer-in-Charge

Hacking out old broken glass any thicknesss & size from frames of any description fixed with putty or beads etc complete all as specified and directed by Engineer-in-Charge

Demolition of plain cement concrete of any description and in any position not other wise specifically provided complete all as specified and directed by Engineer-in-Charge

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m depth for foundation, etc or for shafts, wells, cesspits, manholes,pier holes, etc not exceeding 10 Sqm on plan and not exceeding 1.5m in depth and getting out as in hard dense soil complete all as specified and directed by Engineer-in-Charge

Material & labour for PCC (1:4:8) type D 2 using 40 mm graded stone agreegate as in foundation, filling or mass concrete complete all as specified and directed by Engineer-in-Charge

Material & labour for brick work with sub class 'B' bricks (old Size) straight or curved on planot exceeding 6 m mean radius and built in CM (1:6) complete all as specified and directed by Engineer-in-Charge

All as per item No 21 above but half brick thick wall built in CM 1:4.

Material & labour for 20-25mm thick, machine cut, Kota stone slab, as in floors, steps, landing etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of slab, including cutting, polishing etc. with and including 20mm thick screed bed in CM 1:4 complete all as specified and directed by Engineer-in-Charge

All as per item 23 above but as in skirting/ riser/ dado etc with and including 10 mm thick backing coat in CM 1:3 complete all as specified and directed by Engineer-in-Charge

Extra over Kota stone slabs for edge polishing/ chamfering/ noising/ grooves/ bevelling complete all as specified and directed by Engineer-in-Charge

Material & labour for vitrified ceramic tiles 10 mm thick (square /rectangular) polished dark shade, area of each tiles not exceedingeeding 0.36 Sqm, in floor etc set and jointed in neat cement slurry and pointed white or coloured cement to match the dark shade of the tiles, with and including screed bed in CM (1:6), 20mm complete all as specified and directed by Engineer-in-Charge.

All as per item No 26 above but as in skirting including 10mm thick rendering in CM (1:4) as backing coat etc

Material & labour for Non skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11Sqm but not exceedingeeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of the tiles with and including 20mm thick screed bed in CM (1:4) complete all as specified and directed by Engineer-in-Charge.

Material & labour for Coloured glazed ceramic tiles in vertical surface 450 x 350 x 7mm thick, set and jointed in neat cement paste and pointed in coloured cement to match the shade of the tiles with and including 10 mm thick backing coat in CM (1:3) complete all as specified and directed by Engineer-in-Charge

Material & labour for 50 mm thick PCC 1:2:4 type B1 using 20 mm graded stone aggregates as in floor finished cement concrete surfaces even and smooth using extra cement complete all as specified and directed by Engineer-in-Charge

Material & labour for 30mm thick wearproof toping as specified (incorporating an approved metalic floor hardner) laid on concrete floors and pavings, and finished even and smooth (exceedingept metalic Hardner) complete all as specified and directed by Engineer-in-Charge

Supply & fix glass dividing strips 3mm thick, 28mm wide

Supply only approved metalic hardner.

Material & labour for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types and including 15mm thick screed bed in CM 1:4 complete all as specified and directed by Engineer-in-Charge

Material & labour for granite (of any type) tiles 20mm thick machine cut in skirting/dado laid over cement screed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing of type and including 10 mm thick backing coat in CM 1:3 complete all as specified and directed by Engineer-in-Charge

Material & labour for water proofing plaster for sunken portion in CM 1:3, 15 mm thick in two coats using Pidiproof LW+ water proofing chemical of Dr. Fixit or equvalent as per manufacturer's instruction and finishing the surface even and smooth without using extra cement. (Water Proofing Chemical shall be measured and paid separately) complete all as specified and directed by Engineer-in-Charge

Material & labour for water proofing treatment of sunken floor/wall surfaces by applying two coats of water proofing chemical and cement mix in ratio 1:1.5, (PIDICRETE UPR or equivalent approved water proofing chemicals), complete all as per manufacture's instructions and as directed. Make : Dr. FIXIT, Chemisol, Choksy Chemicals complete all as specified and directed by Engineer-in-Charge

Material & labour for PCC 1:7:12 type F2 using 40 mm graded stone aggregate as in filling (sunken portion) complete all as specified and directed by Engineer-in-Charge

Material & labour for PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate, using Pidiproof LW+ water proofing chemical of Dr. Fixit or equvalent as per manufacturer's instruction , as sub floor, 40mm thick. (Water Proofing Chemical shall be measured and paid separately) complete all as specified and directed by Engineer-in-Charge

Taking down shutters exceeding 1.00 Sqm but not exceeding 2.00 Sqm & refixing in the same opening only after repairing complete all as specified and directed by Engineer-in-Charge

Supply & fix powder coated aluminium frame/shutters for doors, windows, ventilators and partitions with one or more rebates, aluminium nosing patti for steps etc. including joining cleat for fixing, locking arrangement, rubber beading, screws, handles, hinges, tower bolts etc complete all as specified and directed by Engineer-in-Charge

Supply & fix 4 mm thick bakelite sheet with decoratve choice laminated on both side complete all as specified and directed by Engineer-in-Charge

Material & labour for aluminium anodised Deco grill 7.5 mm size DG-102, fixed to E/H frames, 1.5mm th, bar size 6.2mm and 7.5mm thick in required sizes complete all as specified and directed by Engineer-in-Charge

Supply & fix 12 mm thick Medium density fibre board, with decorative laminates on both side interior grade, fixed to timber/ Aluminium frame work with screws complete all as specified and directed by Engineer-in-Charge.

Supply & fix 5.5 mm thick sheet glass, ordinary quality, in any size of pane complete all as specified and directed by Engineer-in-Charge.

Material & labour Solar control film 25 micron reflective fixed to glass panes complete all as specified and directed by Engineer-in-Charge.

Supply & fix 4mm thick figured glass,pin headed type, in squares not exceeding 0.5 Sqm in each pan complete all as specified and directed by Engineer-in-Charge.

Supply & fix stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.4mm complete all as specified and directed by Engineer-in-Charge.

Supply & fix for 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engineer-in-Charge.

Supply & fix 35 mm thick flush shutters, solid core construction, with block board core and ply wood face panels, commercial type on both side complete all as specified and directed by Engineer-in-Charge.

Supply & fix Aluminium anodised sliding door bolt 300m long, with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed by Engineer-in-Charge.

Supply & fix Stainless Steel but hinges 100mm size complete all as specified and directed by Engineer-in-Charge.

Supply & fix aluminium anodised Barrel tower bolts of extruded section, length of bolt 200mm complete all as specified and directed by Engineer-in-Charge.

Supply & fix Extrude aluminium anodised alloy handles, fabricated type 150mm size complete all as specified and directed by Engineer-in-Charge.

Supply & fix false ceiling with powder coated exposed GI grid suspension system (E-Grid T-2430 or equvalent load carrying capacity with mid span deflection not exceeding. 1/360 span with hanger spacing of 1200mm c/c) consisting of main runner 3600mm long of size 35mm x 23.5mm x 1.5mm thick, cross Tee 1200mm /600 mm long and wall angle of size 23.5mm x 23.50mm x 1.5mm thick. The main runners to be placed @ 1200 mm, the cross Tee 1200mm will be inserted in the pre cut slots of main runner at a regular interval of 600mm to form a modular grid of 1200 mm x 600mm. Additional cross Tees of 600mm shall be placed perpendicular to the cross tee 1200mm long to finally form a grid of 600 mm x 600 mm. Grid of modular size 600mmX600mm shall be supported by 2 mm dia G.I. wire from purlins/soffit with and including 4 mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber /GI / Aluminium framework with screw complete all as per manufacturer's instruction .

Supply & fix Door closer, Aluminium (die cast) body,hydraulically regulated, designation No. 3, unversal type suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg complete all as specified and directed by Engineer-in-Charge.

Supply & fix steel rolling shutters, 1.25mm laths thickness, without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated complete, push-pull or manual type complete all as specified and directed by Engineer-in-Charge.

Supply & fix pre-painted galvalume aluminium zinc coating GI baseds corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

All as per item No. 58 above but plain galvalume sheets for ridges/ Flashings complete all as specified and directed by Engineer-in-Charge.

Material & labour for 1.5 mm thick galvanised steel sheet as in Valley gutters fixed with rivets or other suitable arrangements over MS brackets trapezoidal shape of required profile with desired slope etc complete all as specified and as directed by Engr-in-Charge.

Material & labour for PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate, as roof kerbs/pading, using Pidiproof LW+ water proofing chemical of Dr. Fixit or equ. as per manufacturer's instruction, (Water Proofing Chemical shall be measured and paid seperately) complete all as specified and directed by Engineer-in-Charge.

Roughening Surfaces of old Concrete Floor by picking, sweeping clean and washing down with water to remove dust etc brussing neat cement slurry with 3.0 Kg of cement per Sqm complete all as specified and directed by Engineer-in-Charge.

Material & labour for the roof surface thoroughly wire brushed, washed and dried up and cleaned of all foreign matter and dust to receive bituminous primer, apply bituminous based cold applied primer @ 270 to 300 gms/ Sqm manufactured by the same agency as that of APP all as per manufacturers instructions. Laying 5 layered, 4 mm thick APP (A tactic poly propylene) modified membrane reinforced with 180 GSM (Gms/ Sqm) of non woven polyester mat, applied by thermo fusion using LPG torch on the bottom portion of the membrane with an overlap of 75mm in longitudinal direction & aluminium paint over it complete all as specified and directed by Engineer-in-Charge.

Material & labour for cement concrete tiles 25cm x 25cm x 22mm thick, machine pressed, (with grey cement & no pigments), set jointed and pointed in neat cement slurry in floors over and including 15 mm thick bedding layers in CM 1:3 complete all as specified and directed by Engineer-in-Charge.

Cutting chases in brick work/concrete for inserting water proofing membrane in to the parapet walls/column & making good to facing where required and pointing in CM 1:3 to the groves, cutting not exceeding. 10 cm girth complete all as specified and directed by Engineer-in-Charge.

All as per item No 65 above but cutting in concrete not exceeding. 10 cm girth.

Disconnecting existing tanks, exceeding. 500 & not exceeding. 1000 litres capacity, setting aside (or lowering if required) for repair, cleaning, etc and hoisting if required reconnecting and re-fixing in position complete all as specified and directed by Engineer-in-Charge.

All as per item No 67 above but exceeding. 1000 & not exceeding. 2000 litre capacity.

All as per item No 67 above but tanks, 5000 litre capacity.

Supply & fix 15 mm dia medium grade galvanized steel tubing with all fittings fixed to walls, ceilings or laid under floors complete all as specified and directed by Engineer-in-Charge.

All as per item No 70 above but 20 mm bore pipe.

All as per item No 70 above but 25 mm bore pipe.

Cutting chases in brick work for concealed water tubing and making good, cutting exceeding 10 cm but nexceeding. 20 cm girth complete all as specified and directed by Engineer-in-Charge.

Supply & fix 15 mm bore dia of pipe, brass chromium plated fancy type bib tap, fixed in repairs complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs 15 mm size Stop Valves fancy type chromium plated screwed down high pressure with crutch or butterfly handle handle screwed both ends complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repair 15 mm dia fancy type pillar tap cast copper alloy with capston heads chromium plated screwed down high pressure with or without hot or cold with long screws shanks and fly nuts screwed for iron pipes complete all as specified and directed by Engineer-in-Charge.

Supply & fix conclusive push button taps of cast copper alloy, screwed for PPR pipe 15 mm bore and fixed in repairs complete all as specified and directed by Engineer-in-Charge.

Supply & fix PVC Connections 15 mm size with PTMT nuts of length 600mm complete all as specified and directed by Engineer-in-Charge.

Supply & fix brass chromium plated shower rose 125mm size, fixed in repairs complete all as specified and directed by Engineer-in-Charge.

Supply & fix 10 litres capacity PVC low level flushing cistern of approved make including ball valve,syphon set, inlet and outlet pipe complete all as specified and directed by Engineer-in-Charge.

Supply & fix brass chromium plated, tubular towel rail 20 mm dia, D type, 60 cm long between flange, fixed in repairs complete all as specified and directed by Engineer-in-Charge.

Supply & fix Soap dish, vitreous china white, approximat size 160 x 160 x 90 mm fixed in repairs complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repair white vitreous china squatting pan, 'orissa' pattern, water closet of size 580x440mm with integral foot rest, P/S trap complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs white vitreous china washed down water closet pan, (pedestal pattern), white, with and including P/S trap, PVC solid type seat cover complete all as specified and directed by Engineer-in-Charge.

Supply & fix vitreous china urinals,half stall type, flat back, white, with grating and union for discharge pipe, complete including providing and fixing plugs, bedding urinal against wall in CM 1: 2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement , fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe.(exceedinglusive of fixing supply pipe to flushing cistern , trap and waste pipe) complete all as specified and directed by Engineer-in-Charge.

Material & labour Urinal spreader of PTMT any colour for fixing with 15mm dia pipe (Minimum weight 60gms) complete all as specified and directed by Engineer-in-Charge.

Supply & fix white glazed vitreous china wash hand basin of size 550x400mm with and including CI brackets, 32mm bore brass CP waste fitting, inlet/ outlet, PVC flexible pipe, 600mm size for 15 mm bore pipe with PTMT nut and washers etc complete, fixed in repairs complete all as specified and directed by Engineer-in-Charge.

Supply & fix vitreous china urinal partitions white of size 310X700mm, slabs, terminating about 40 cm above floor line, fixed in repairs complete all as specified and directed by Engineer-in-Charge.

Supply & fix 110mm dia PVC ( SWR) grade pipes, single socketed in any length with rubber ring joints fixed to walls and laid in flloors/trenches complete all as specified and directed by Engineer-in-Charge.

Supply & fix 75mm dia PVC ( SWR) grade pipes single socketed in any length with rubber ring joints fixed to walls and laid in flloors/trenches complete all as specified and directed by Engineer-in-Charge.

Supply & fix 110mm dia PVC ( SWR) grade single/double T/Y, bends etc. with or without access doors including fixing clips complete all as specified and directed by Engineer-in-Charge.

All as per item No 92 above but 75mm dia

Material & labour PVC SWR floor trap 75mm, plain with grating including setting and jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.

Supply & fix 50 mm, low density polyethylene pipes (LDPE) of pressure rating 6 kgf/Sqcm fixed complete to walls, ceilings or in floors etc complete all as specified and directed by Engineer-in-Charge.

Supply & fix 160 mm dia PVC (SWR) grade pipes single socketed in any length with rubber ring joints fixed to walls with and including fixing clips, bends, elbow, shoes bends etc. (Note:- Measurment shall be taken along the centre line of the pipes.) complete all as specified and directed by Engineer-in-Charge.

Material & labour for rendering 15 mm thick in CM (1:6) on fair faces of brick work or concrete surfaces finishing the surface fair and even complete all as specified and directed by Engineer-in-Charge.

Material & labour for rendering 5 mm thick in CM 1:3 on fair faces of brick work or concrete surfaces in ceiling finishing the surface even and smooth complete all as specified and directed by Engineer-in-Charge.

Material & labour for plastering in CM 1:4, 20 mm thick in two coats (15 mm under coat plus 5mm finishing coat) using Pidiproof LW+ water proofing chemical of Dr. Fixit or equvalent as per manufacturer's instruction and finishing the surface even and fair. (Water Proofing Chemical shall be measured and paid seperately) complete all as specified and directed by Engineer-in-Charge.

Material & labour for sagol finish on newly plastered surfaces of wall/ ceiling, to a thickness not less than 1mm trowlled to an even and smooth finish complete all as specified and directed by Engineer-in-Charge.

Material & labour for providing 12 mm dia holes of 75mm deep @0.6 m c/c at junction of beams and columns as co-ordinal points for inserting/ pouring mixture of resin base latex polymer and cement slurry by pressure grouting for column, beams and slabs, including sealing the holes with CM 1:3 complete all as specified and directed by Engineer-in-Charge.

Material & labour for taking down, chipping and removing the loose, spoilt, damaged cement concrete, cement mortor surfaces of RCC Columns, beams, walls, chajjah etc and exposing the reinforced cement , wire brushing and cleaning the exposed steel reinforced bar, applying rust remover over the cleaned re-bar surface wash the re-bar with clean water for removing all rusts from the old re-bar surfaces, fixing new reinforcement for strengthen the members as required, applying two coats of epoxy zinc primer on new and old steel surfaces, saturate the substrate with water applying one coat of polymer modified bond coat on affected concrete surfaces and finally providing polymer modified cement/ microconcrete and quartz sand mortor in CM 1:3 mix, 40mm thk in two coats, using polymer @ 10 to15% by weight of cement complete all as specified and directed by Engineer-in-Charge. Make : Dr. Fixit/ Sunanda/ chemestik/ Fosrok. Note :-(New reinforcement and MS Sections will be measured and paid separately)

Supply only Water proofing chemical Pidiproof LW+ of Dr. Fixit or Equvillant complete all as specified and directed by Engineer-in-Charge.

Supply only readymix microconcrete mixture complete all as specified and directed by Engineer-in-Charge.

Supply & fix welded steel wire fabric, cut to length, fixed to steel members /reinforcement steel, weigh per Sqm nexceeding. 4 Kg complete all as specified and directed by Engineer-in-Charge.

Material & labour for TMT mild steel bars, 10 mm dia and over, cut to length bent to shape required, including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-410-S or Fe-410-0 complete all as specified and directed by Engineer-in-Charge.

All as per item above but but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

Supply & fix for rolled mild steel Sections of Grade Fe 410-W, (Gde- E-250) quality-A, as in post, runners, rafters, purlins steps etc fixed with connecting plates including bending, welding complete all as specified and directed by Engineer-in-Charge.

All as per item No 108 above but MS Plain Plates

All as per item No 108 above but MS chequered Plates

Material & labour for preparation of newly plastered surfaces of wall, applying two coats of oil emlusion distemper over a coat wall care putty of 3mm thick and alkali primer complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of newly plastered surfaces of walls, applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.

All as per Item No 112 above but in ceiling

Material & labour for preparation of newly plastered or un plastered wall surfaces, over 10cm girth, applying two coats of 100% acrylic, weather resistant emlusion over a coat of exterior wall primer complete all as specified and as per manufacturer's instruction

Material & labour complete removal of existing plastered wall surfaces, over 10cm girth, preparation of surfaces, applying two coats of 100% acrylic, weather resistant emlusion over a coat of exterior wall primer complete all as specified and as per manufacturer's instruction.

Material & labour for complete removal of existing treatment on wall surfaces and applying a coat wall care putty 3mm thick on plastered surfaces, preparatory to distempering and applying two coats of oil bound distemper over a coat of wall primer complete all as specified and directed by Engineer-in-Charge.

Material & labour for complete removal of existing treatment in ceiling surfaces and applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of new steel surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

Material & labour for complete removal of old decorated steel surfaces of any description over 10 cm width or girth, applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of old decorated wooden surfaces of any description over 10 cm width or girth, applying a coat of synthetic eanmel paint complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of new wooden surfaces of any description over 10 cm width or girth, applying two coats of synthetic enamal paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Supply & fix for 4mm dia galvanised steel wire, 150x100mm mesh, made up into mattresses or cages, lapped, wired and laid in position, including closing after filling complete all as specified and directed by Engineer-in-Charge.

Material & labour 100 mm thick Cement concrete type B-2, 1:2:4 (40mm graded aggregate) as in hardstanding complete all as specified and directed by Engineer-in-Charge.

Material & labour Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade over 50 mm thick sand cushioning complete all as specified and directed by Engineer-in-Charge.

Material & labour for Stainless steel decorative railings (design and pattern as approved) made out of SS pipes, SS flats, SS plates etc. complete with and including necessary welding, buffing/ polishing and fixing complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, levelling , watering and well ramming in layers not exceeding 25 cm in hard/dense soil complete all as specified and directed by Engineer-in-Charge.

Removing debris and exceedingavated material exceeding. 1.50 Km but not exceeding. 15 Km and depositing where directed, in soil complete all as specified and directed by Engineer-in-Charge.

Taking down carefully old U/S point wiring copper/Aluminum (light/ fan /sockets/power) complete with switches, sockets, fan regulators, ceiling roses, lamp holders, brackets,PVC casing caping and PVC/steel conduit complete etc removing material to store for keeping in safe custody and making good to disturbed surfaces complete all as specified and directed by Engineer-in-Charge.Charge

Taking down Submain wiring any size and any run complete and making good the distrubed surface matching with existing surface all as directed by Engineer-in-Charge.

Material & labour for sub-main wiring with 2 runs of 6.0Sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and including heavy grade PVC conduit not less than 25mm dia (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 6.0Sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including making good the distrubed surfaces/locationcomplete all as specified and directed by Engineer-in-Charge.Note: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) Make of wire : Polycab/ Havells/ Finolex

Material & labour in replacement Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed as required, size 3 x 2.5 Sqmm (Phase, Neutral, Earth) through medium grade PVC conduit, not less than 25mm dia, complete all as specified and directed by Engineer-in-Charge.

Material & labour for sub-main wiring with 4 runs of 10.0Sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and including heavy grade PVC conduit not less than 25mm dia (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 10.0Sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including making good the distrubed surfaces/location complete all as specified and directed. Note: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) Make of wire : Polycab/ Havells/ Finolex

Dismantling/Taking down old U/S light fittings removing from site and making good the distrubed surface matching with existing surface all as per directed by Engineer in charge.

Supply and fixing suspension mounted 28W LED 4F WH pendant luminaires and high translucent diffuser provides high quality ecomonic energy saving lighting incl suspension of 1.5mtr (set of 02 Nos) complete fixing arrangement all as specified and directed. Make : Bajaj Cat No 112228 /wipro/CG.

Supply & fix in repair LED light battan fitting 40W prewired complete with all accessories including connecting to ceiling rose with PVC insulated cable 3 core 0.5 Sqmm multistranded copper conductors complete all as specified & directed by Engineer-in-Charge. Make: CG/Wipro/Bajaj cat No

Supply and fixing in repair suspension mounted 2 x 18W LED pendant Luminaires and high translucent diffuser provides high quality ecomonic energy saving lighting incl suspension of 1.5mtr (set of 02 Nos) complete fixing arrangement all as specified and directed. Make : CG/wipro/Bajaj cat No 112182 & 112432

Supply & fix LED bulk head light fitting, 1x10 W luminaries protected to IP65, with front toghened glass including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V, 50 HZ complete all as specified and directed by Engineer-in-Charge. Make : Bajaj Cat No 112334/wipro/CG

Dismantling and taking down highbay/security/flood light fittings of any wattage or size /building security lights accessories etc all as per directed by Engineer in charge.

Supply & fix in replacement industrial highbay luminaire 240V 150W, LED type with die cast anodized aluminium housing with necessary fixture all as specified and directed by Engineer-in-Charge. Make : C&S /Wipro/CG

Supply and fixing LED 120W building security light fittings with high pressure die cast housing with toughened glass and individual LED with secondary optics and IP66 protection complete all as specified and directed by Engineer-in-Charge. Make : C&S /Wipro/CG

Supply & fix MS arms bracket (BEST-Pattern) for mounting one in Nos Street/Building security light fitting 40 mm medium grade GI at an angle of 30 degree including clamp/nut/bolts & washers to brace the same properly with duky painted in synthetic enamel paint of two coat in silver colour complete all as specified & directed by Engineer-in-Charge. Note : The rate quoted deemed to be included the making the good to the disturbed surfaces to match with the existing surfaces.

Taking down old u/s MCB DBs complete with MCBs of any type and capacity & making good to the disturb surfaces all as directed by Engineer in charge all as specified.

Supply & fix of double door type SPN DB 08 Way ,240V with 100A copper busbar each phase , double door type IP-54 IK 09 protection suitable for housing MCB's all as specified and directed by Engineer-in-Charge. Make: Legrand cat No 507641 /Seimens/GE. Note : MCB DBs shall be concealed in wall where ever posible including making good the surface to match with surrounding.

Supply & fix sheet metal enclosure TPN DB 8 Way,415V with 200A busbar, double door type IP-54 protection suitable for housing MCB's all as specified and directed by Engineer-in-Charge. Make: Siemens/Legrand/GE Note : DBs shall be conceeled in wall where ever posible including making good the surface to match with surrounding.

Supply & fix in repair of sheet metal enclosure single pole box,without bus bar 240V suitable for housing SP MCB all as specified and directed by Engineer-in-Charge. Make: Siemens/Legrand Cat No 607712/ABB/C&S . Note : MCB DBs shall be conceeled in wall where ever posible including making good the surface to match with surrounding.

Supply & fix MCCB 415 volts, 125Amp 4 pole of 16 KA ICS= 100% ICU with fixed thermal magnetic setting including spreader terminal of suitable size and making connections complete all as specified & directed. Make : Legrand Cat No 420016/Seimens/GE

Supply & fix MCB SP 6-32 Amps,10KA, 'C' series 240V complete all as specified and directed. Make : Legrand/Seimens/GE

Supply & fix MCB SP 40 Amps,10KA MAKE: C&S/Legrand / seimens/GE

Supply & fix MCB SPN 63 Amps,10KA 'C' series 240V complete all as specified and directed. Make : Legrand/Seimens/GE

Supply & fix MCB TP 40 Amps,10KA 'C' series 415V complete all as specified and directed. Make : Legrand/Seimens/GE

Disconnecting & taking down, strip opening, cleaning all parts of ceiling fan of any make and size after greasing ball bearing with specified quilty grease painting with sythetic enamal paint refixing in original porition, connecting electrically and testing complete all as specified and directed

Disconnecting & taking down, strip opening, cleaning all parts of exhaust fan of any make and size after greasing ball bearing with specified quilty grease painting the frame & lower with sythetic enamal paint refixing in original porition, connecting electrically and testing complete all as specified and directed

Refixing only exhaust fan in position same including making electric connection complete all as specified & directed at the item No .

Supply & fix Ceiling fan 1200mm sweep, suitable for operation on 230 / 240 V. 50 Hz, single phase, A.C, supply complete including connecting up with 3 core flexible cord of size 23/0.0076mm from ceiling rose to fan all as specified and directed. Make : HAVELLS/ Bajaj & Crompton

Material & labour for fabrication and fixing of ceiling fan hooks and clamp with nuts ,bolts and washers and down rod at site required size complete all as specified and directed.

Supply & fix exhaust fans in metalic body with powder coated paint , Single piece plastic blade AC Single Phase 230 V capacitor run motor of size 380mm sweep (Heavy duty), including louvers/shutter and connecting up 3 core flexible cord of size 23/0.0076mm from ceiling rose to exhaust fan all as specified and directed. Make : HAVELLS/ Bajaj & Crompton

Supply & fix wall mounted fan, 450mm sweep, heavy duty single phase oscillating complete fixing accessories required at site and making good the distrubed surface & connection copper cable from ceiling rose to exhust fan complete all as specified and directed by Engineer-in-Charge. Make: model No Havells (D'zire')/Usha/CG/Orient/BAJAJ/CG.

Material & labour for point wiring complete with proper colour coding using PVC insulated unsheathed multistranded copper conductor cable 1.5 Sqmm size, 1100 volts ISI marked, FRLS grade drawn through and including non metalic rigid, double lock, ISI marked, PVC conduit with all accessories such as tee, bends, elbow, reducers, junction box etcfixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 1.5Sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuty conductor connected to common earth dolly with and including modular box with cover plate frame in any module complete for One light/fan/bell point controlled by one 5A switch complete all as specified and directed. Note: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) Make of wire : Polycab/ Havells/ Finolex/Plaza (c) Electrical wiring above false ceiling shall be drawn through medium grade PVC conduit.

Material & labour for point wiring complete with proper clour coding using PVC insulated unsheathed multistranded copper conductor cable 1.5 Sqmm size, 1100 volts ISI marked, FRLS grade drawn through and including non metalic rigid, , ISI marked, PVC conduit with all accessories such as tee, bends, elbow, reducers, junction box etcfixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 1.5Sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuty conductor connected to common earth dolly with and including modular box with cover plate frame in any module complete for One 5 pin, 5A switch socket combination on the independent board complete all as specified and directed. Note: (a) Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) Switch socket measured & paid separately. (c) Make of wire : Polycab/ Havells/ Finolex/Plaza

Material & labour for point wiring complete with proper clour coding using PVC insulated unsheathed multistranded copper conductor cable 1.5 Sqmm size, 1100 volts ISI marked, FRLS grade drawn through and including non metalic rigid, double lock, ISI marked PVC conduit with all accessories such as tee, bends, elbow, reducers, junction box etcfixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 1.5Sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuty conductor connected to common earth dolly with and including modular box with cover plate frame in any module complete for One 5A switch socket combination on the same board complete all as specified and directed. Note: (a) Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) Switch socket measured & paid separately.

Material & labour for point wiring complete with proper clour coding using PVC insulated unsheathed multistranded copper conductor cable 4.0 Sqmm size, 1100 volts ISI marked, FRLS grade drawn through and including non metalic rigid, double lock, ISI marked, not less than 25mm casing caping with all accessories such as tee, bends, elbow, reducers, junction box etcfixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 2.5Sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuty conductor connected to common earth dolly with and including modular box with cover plate frame in any module complete necessary electric connection for each workstation point comprising of 03 Nos 6A sockets and 01 No 15A socket on same board complete all as specified and directed. Note: (a) Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) Switch socket measured & paid separately (c) Make of wire : Polycab/ Plaza/Havells/ Finolex

Material & labour for point wiring complete with proper clour coding using PVC insulated unsheathed multistranded copper conductor cable 2.5 Sqmm size, 1100 volts ISI marked, FRLS grade drawn through and including non metalic rigid, double lock, ISI marked PVC conduit with all accessories such as tee, bends, elbow, reducers, junction box etcfixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 2.5Sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuty conductor connected to common earth dolly with and including modular box with cover plate frame in any module complete for One 5 pin, 15A switch socket combination on the independent board complete all as specified and directed. Note: (a) Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) Switch socket measured & paid separately (c) Make of wire : Polycab/Plaza/ Havells/ Finolex

Supply & fix ceiling rose surface bakelite 65 x 50mm, flush type, 3 terminals complete all as specified and directed by Engineer-in-Charge. Make : Anchor/Cona/Plaza

Supply & fix modular switch 1 way 6A complete all as specified and directed by Engineer-in-Charge. Make: Roma/Legrand

Supply & fix modular socket, 6A - 2/3 pin combined 2 modules complete all as specified and directed by Engineer-in-Charge. Make: Anchor/Roma/Legrand.

Supply & fix modular switch 1 way 16A,1 module complete all as specified and directed by Engineer-in-Charge. Make: Anchor/Roma/Legrand.

Supply & fix modular socket 6/16A,2/3 pin, combined 2 module complete all as specified and directed by Engineer-in-Charge. Make: Anchor/Roma/Legrand.

Supply & fix for modular fan step regulator, 120W - 2 modular complete all as specified and directed by Engineer-in-Charge. Make: Anchor/Roma plus/Legrand

Supply & fix in replacement of epoxy insulator suitable for earthing strip complete including bolts, washers complete all as specified and directed by Engineer-in-Charge.

Supply & fix in replacement of air termination copper rod single pointed 300 mm long and 12 mm dia complete all as specified and directed by Engineer-in-Charge.

Material & labour in replacement of test point terminal block made out of gun metal of phospharus bronze fixed in 75 x 75 x 25mm MS/polycarbonate enclosure drilled & screwed including 3 Nos of 8mm dia 25mm long screw complete all as specified and directed by Engineer-in-Charge.

Earthing complete with galvanised steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2.25 mtr below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to galvanised earth strip 32x6mm fixing on wall by means of bolts, nuts check nut & washers of galvanised iron or steel & other end of the earth strip connected to earthing test point including complete exceedingavation and earth work in soft/loose soil and disposal of surplus soil to a distance not exceeding 50 meters, PCC Chamber (1:3:6) type C-2 precast RCC cover with frame, funnel wire mesh, 20mm bore light grade galvanised iron or steel pipe for water, charcoal or coke and salt in alternative layers of 15cm compacted thickness all round the earth electrode complete alll as shown in electrical plate No 5 of SSR part-I including welding with suitble electrode and testing complete all as specified and directed by Engineer-in-Charge.

Material & labour for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire complete all as specified and directed by Engineer-in-Charge.

Supply & fix in replacement of earth continuity conductor with adequate size saddle fixed to wall on batten or recess or any other indicated situation for loop earthing etc as required 32mm x 6mm GI strip complete all as specified and directed by Engineer-in-Charge.

Garima Construction Co

Shetty Construction Co

Darpan Construction

Star Construction Co.