PROVN OF TOILET FOR JCOS AND ORS NEAR MANEKSHAW HALL , PROVN OF 40 X TRACK LIGHT ALONGWITH TRACKS, 17 X BLDC FAN AND 03 X ROLLING SHUTTER WITH ACP BOARD INCLUDING 09 LIGHTS AT SHOP NO 18,19, 20 OF STN SHOPPING COMPLEX AND PROVN OF BRICK DRAIN

Amount

Surface dressing n.exc 15cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavating in trenches , n.exc 1.5 m wide and n.exc 1.5 m depth for foundation etc or for shafts, wells, cesspits ,manhole pier hole, laying of cables, pipes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in any kind of soil Note : Manual excavation to be done. During excavation if any damage occured to existing cable any type/ water pipe line, it will be contractor responsibilty to get it repair and make functional by providing jointing kit etc without any extra cost. Contractor has to repair it within 24 hrs so that essential service can not be effected due to such damage.If contractor fails to repair it within 24 hrs penalty @ Rs 500/- will be charged to contractor. In this GE decision will be final, conclusive and binding.

Excavation over areas n. exc1.5m deep and getting out in soft/loose soil complete all as specified and directed.

M&L for 300 mm thick (compacted) in three layers of each 100mm thick in pavings, with mix of fly ash, clinker & stone dust in the proportion of 1:3:6 (ie 10% fly ash, 30% clinker and 60% stone dust ) laying in layers n. exc 10cm thick, watering, ramming and compacted with hand/power roller 8 to 12 tonn roller to required camber and gradient complete all as directed by Engineer-in-Charge.

M&L Hardcore of gauge n exc. 63mm broken stone or boulders, deposited, spread and leveliled in layers n exc. 150mm thick, watered and rammed to a true surface complete all as spd and directed.

M & L Moorum/red bajri/clinker filling in floors or pavings, laid in layers n.exc 15 cm thick, spread, levelled and rammed including watering complete all as spd and directed.

M&L for 50mm thick river sand filling under floors or in foundations including watering and consolidation complete all as spd and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose complete all as spd and directed.

Removing surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as spd and directed.

M&L plain Cement concrete 1:3:6, type C-2 (using 40mm graded crushed stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in bed concrete for foundation filling & mass concrete complete all as spd and directed.

M & L for reinforced cement concrete (Design Mix) M-25 as in foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc. and mass concrete etc complete all as directed.

M & L for reinforced cement concrete (Design Mix) M-25 in columns, pillars, piers, etc. complete all as spd and directed.

M & L for reinforced cement concrete (Design Mix) M-25 in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as spd and directed.

M & L for reinforced cement concrete (Design Mix) M-25 in beams, cantilevers, bressummers, lintels over 1.5m span complete all as spd and directed.

M & L for reinforced cement concrete (Design Mix) M-25 ) as Chajjas complete all as spd and directed.

M & L for providing precast cement rainforced concrete B-1 1:2:4, type (20mm graded crushed stone aggregate) as in cover slab for manhole and similar article with plain face set in cement mortar 1:6 complete all as specified and directed.

M & L Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified as directed.

M & L for plain cement concrete B-0 1:2:4 type (12.5mm graded crushed stone aggregate) in cills, steps, plinth courses, string courses, lacing courses, parapets, copings, kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directed rounded or chamfered on edges all as specified.

M&L for Plain Cement concrete 1:3:6 type C-1(using 20mm graded crushed stone aggregate) in surface channels and drains and Manholes complete all as specified and directed.

M&L for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter for rough finished surfaces of concrete complete all as specified and directed..

M & L for formwork for rough finished surface of concrete (flat surface) to sides of pillars, posts, struts, piers, columns, and stanchions fair finished on concrete surfaces complete all as spd and directed.

M & L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for fair finished surfaces of concrete complete all as spd and directed.

M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work for rough finished surface, not exceeding 200m thick (Horizontal or sloping) for fair finished surfaces of concrete complete all as spd and directed.

M&L for formwork to chullah hoods, chajjas, troughs and similar items including edges for fair finished surfaces of concrete complete all as spd and directed.

M & L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as spd and directed.

M & L TMT bar 10mm dia and over, as in reinforcement, cut to length, bent to shape etc, including binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M & L TMT reinforcement bar, conforming to Fe-500, 6mm to 8mm dia and over cut to length , bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed) not less than 0.9mm dia or securing with chips.

M&L for brickwork with fly ash old size bricks straight or curved on plan to any radius built in CM 1:6 complete all as spd and directed.

M&L for brick work with fly ash old size bricks straight or curved on plan exc 6 m mean radius build in CM 1:4 all as specified as directed.

M&L for brickwork with fly ash old size bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as spd and directed.

M&L for Rendering 15 mm thick cement plaster in CM 1:4 on fair faces of brick/concrete surfaces finished fair and even, mixed wth water proofing compound admixture (if directed) as per manufacturer's instruction, complete all as specified and directed. Note :- WPC will measuered and paid separatly under relevant item of schedule.

Supply only liquid Water proofing compound ISI Marked complete all as spd and directed.

M&L Rendering 15 mm thick cement plaster in CM 1:6 on other than fair faces of brick/concrete work surfaces finished fair and even complete all as specified and directed..

M&L for rendering 5 mm thick in CM 1:3 on fair faces of brick work or concrete wall surfaces & finishing the surfaces fair and even on ceiling complete all as spd and directed.

M&L for grading roof in cement mortar 1:3, 25mm thick in edge and 50mm thick in ridge including necessary curing complete all as specified in SSR Part I clause No 11.42.2

M & L for providing water proofing treatment with a layer of APP based polymeric membrane, 3 mm thick (minimum), weighing not less than 3.60 kg/Sqm reinforced with polymer non woven fabric (weighing not less than 160 gm/ Sqm) shall be applied over one coat of cold bituminious primer @ 0.40 ltr/ Sqm ( membrane shall be laid using butane torch and sealing all joints etc, complete all as specified and directed .( Note: The overlaps shall be of minimum 75 mm on longitudinal direction and 100 mm on transverse direction) complete all as specified and directed.

M&L for one coat of aluminium paint over APP membrane complete all as specified and directed.

S&F for factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows and other frames/chowkhat of size 50x100 mm comprising of virgin PVC polymer of K value 58-60 (suspension grade ), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS scews having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200N (face) and 1100N (Edge), minimum compressive strength of 58 N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in -Charge. (M.S. hold fast/lugs or SS dash fasteners shall be paid for separately) Note :- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile demension on plus side shall be acceptable but no extra payment on this account shall be made. .

S&F for 35mm thick factory made single extruded WPC (wood polymer composite) solid wire gauzed i.e. panel will be of wire gauze in lieu of panel. The comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum frame density of 650 kg/cum, screw withdrawal strength of 1800N (face) and 900N (Edge), minimum compressive strength of 50 N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hings of required size with necessary full body threaded star headed counter sunk S.S screws , all as per direction of Engineer-in -Charge. Note :- Stainless steel butt hinges and necessary SS Screws shall be paid separately).

M&L for anodised powder coated aluminium frame for doors,windows, ventilators and partition with one or more rebates including joining cleat for fixing etc.with power coating (minimum thickness of powder coating 50 micron) complete all as specified.

S&F for powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified.

S&F Sheet glass 5.5 mm thick , ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as spd and directed.

S&F 100mm long stainless steel butt hinges with stainless steel screws complete all as specified and directed.

S&F 200 mm long stainless steel barrel fancy tower bolt of extruded section.

S&F 200mm long stainless steel fancy type handles complete all as specified and directed.

S&F 300 mm long stainless steel fancy type sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolts with rolled or drawn brass bolts and fixed complete all as specified and dirceted.

M & L 75 mm thick plain cement concrete M 7.5 (Nominal Mix) using 40 mm nominal size graded stone aggregates finished surface even and rough as as in sub base floor/paving/hardstanding complete all as specified and directed.

M&L for 75 mm thick cement concrete M10 (Nominal Mix) with 40mm graded crushed aggregate finished even and fair laid to a slope of 1 in 12, laid in alternate bays, each bay not exceeding 3 m length with joint filled with bituminous mastic filling comprising a mixture of 1 part of heated Industrial bitumen 85/25 grade and two parts of heated sand as in plinth protection complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-0, (using 12.5 mm graded stone aggregate) 25 mm thick as in floor for receiving screed bed for floor finishes complete all as specified and directed..

M&L Non Skid coloured ceramic tiles 8 to 10 mm thick (Square/rectangular) area of each tile exceeding 0.38 sqm but not exceeding 1.00 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cemeent to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in CM 1:6 complete all as specified and directed.

M&L for Glazed ceramic designer coloured tiles 8 to 10 mm thick (Square/rectangular) area of each tile exceeding 0.38 sqm but not exceeding 1.00 sqm in wall/dado etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match rendering over 10 mm thick in CM 1:3 on stone masonry surfaces or surfaces other than fair face of brick work/ concrete surfaces complete all as specified and directed.

Material and labour for machine pressed precast concrete interlocking paver prepolished coloured block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as spd and as directed.

M&L for 16 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 20mm thick screed bed in CM 1:6 complete all as spd and directed.

S&F vitreous china counter top wash hand basin (self rimming) leed NC0483 (Size 600 x 400 x 185mm) colour brilliant / off white including fixing brackets and prepolished granite slab of size 1000 x 600mm size and cutting notch of required size as per the wash hand basin to be fixed in it complete all as specified and directed.

S&F basin mixer without pop up chromium plated complete all as specified and directed.

S&F for PVC waste pipe 32 / 40 mm dia of standard length suitable for WHB as required at site complete all as spd and directed.

Cutting chases, pinning in making good to facing on brick walls where required and pointing in cement mortar (1:3) to ends for concealed water tubing and making good, cutting n. exc. 10cm girth complete all as spd and directed.

S&F for 16 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F for 20 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

Supply and fix for Gun metal gate valve,20 mm bore, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions all as specified and as directed.

S&F vitreous china wash down water closet pan, pedestal pattern Pedestal pan and trap(excluding flushing cistern and flush pipe),connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc and including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel CP or aluminised hinging device all as specified and directed.

S&F 10 litre capacity PVC low level flushing cistern with all accessories complete fixed with WC including syphone pipe, PVC flushing pipe of size complete (with brackets).incl flush pipe of plyethene of low or high density of PVC 32mm dia for low level cistern all as specified and directed.

S&F for Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified

S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white minimum), with grating and union for discharge pipe(back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe.

S&F CP Urinal Spreader of any size and any pattern for fixing with 15 mm dia pipe complete all as spd and directed.

S&F 8MM rectangular shaped urinal partition with frosted glass size 450 mm x 900 mm terminating about 40 cm above floor level and fixed with stainless steel clamp on wall complete all as specified and directed.

S&F 15mm bore chromium plated cast copper alloy 2-IN-1 bib cock tap , screwed down for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F 15mm bore fancy type stop valve/angle valve , chromium plated concealed type cast copper alloy, screwed down , high pressure , with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F in Grating square 150 mm size of PTMT (Minimum weight 100gms) complete all as spd and directed.

S&F in Grating with waste hole square 150 mm size of PTMT (Minimum weight 100gms) complete all as spd and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 450mm complete all as spd and directed.

S&F PVC SWR pipes 75 mm bore single socketed in any length with rubber ring joint , laid in trenches or in floors complete all as specified and directed.

S & F PVC (SWR) bends any radius of 75 mm bore with access door.

S&F for PVC (SWR) vent cowl 75 mm bore complete all as spd and directed.

S&F PVC (SWR) floor trap 75mm dia of outlet plain with grating including jointing with solvent cement

S & F PVC (SWR) junction single, (single T) equal or unequal of 75 mm bore complete all as spd and directed.

Material and labour for complete removal of existing treatment (any layers of existing treatment ) from walls/pillars/cornices by scraping down with using steel patti and mechanical sander machine (including provision of dust sucking) upto entire satisfaction of Engineer-in-charge, brooming and washing down with water including applying 1mm thick wall care putty to filling to depressions to make the surface even and smooth by using sander machine (with provision of dust sucking) as directed by Engineer-in-charge and after preparing the surface smooth applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. over and including a coat of primer by using electric paint roller or roller brush, as per existing or as approved tint/colour complete all as specified and as directed.

M&L for prepration of new plastered surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as spd and directed.

M&L for preparation new plastered surfaces and applying three coat of white washing on ceiling complete all as spd and directed.

Material & Labour for preparation of new surfaces of plastered walls and applying Two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. over and including a coat of primer over plastered surfaces of walls complete all as specified.

Cutting into existing manholes 150mm dia pipe for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required complete all as specified and directed.

Supplying and laying of PVC underground drainage sewer system pipe bearing 160 mm dia SN 4 including jointing with couplar, bend tee as per site requirement complete laid in trenches or floors complete all as specified and directed.

Material and labour for plain cement concrete 1:3:6, type C2 (using 20mm crushed graded stone aggregate) bed to drain pipe for 150mm bore of pipe including forming cradles complete all as specifiedand and as directed.

Demolition of cement concrete in ground floor & paving n. exc 15 cm thick (below or above GL) unreinforced complete all as specified and directed.

M&L 6mm thick any colour ACP board (Aluminium composite panel), exterior grade, (approved colour) fixed with aluminium tapperd clip to aluminium frame /other similar frame work all as specified and as directed. Note :- all necessary fittings including aluminium section where reqd included in this rate.

M & L for concealed point wiring for fan/light point controlled by one one way switch complete with 1.5 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red/yellow/blue wires for phases and black wire for neutral),drawn into and including non metalic PVC rigid conduit medium grade of suitable size and conduit accessories fixed on wall, floor, roof etc. and including PVC FRLSH insulated 1.5 sq mm copper conductor for earth continuity (Green Colour) and connected to common earth dolly including sunken in GI terminal box 2.8 mm thick bakelite hylam sheet cover, ISI marked with CM/L no. for mounting switch & sockets ect. Note : a) Note :- Cost of PVC conduit, cutting chases of wal/ceilingl, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

M & L for concealed point wiring complete with 1.5 sq mm FRLSH ,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral),drawn into and including non metalic PVC rigid conduit medium grade of suitable size and conduit accessories fixed on wall, floor, roof etc. and WITHincluding of FRLSH PVC insulated 1.5 sq mm copper conductor for earth continuity (Green Colour) and connected to common earth dolly and including pressed steel terminal flush boxes made out of 1.6 mm thick MS sheet suitable for modular switches concealed in wall , with and including modular cover plate with frame (suitable module) for housing the switches socket,outlet etc.,all as specified and directed by Engineer-in-Charge for one light point controled by one one way 5/6 Amp switch Note:- (a) Note :- Cost of PVC conduit, cutting chases of wall, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

Supply and fixed switch piano flush type, single pole , 5/6 Amps, one way complete all as specified and directed.

Supply and Fixing Modular switch 6 Amp 1 way 1 module size complete all as specified and as directed by Engr-in-Charge.

Supply and Fixing Modular Fan regulator step type 120 watts 2 Module size complete all as specified and as directed by Engr-in-Charge.

Supply & fixed ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified.

S&F LED 20 Watt tube light fitting intregated type, including LED retrofit tube lamp 20 W , LED tube light nominal power 20 Watt, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 110 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 life span of minimum 50000 working hours and LED batten with aluminium housing and polycarbonate diffuser complete fitting including connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fitting complete all as specified & directed. . Note (i) Make of batten and LED tube lamp should be of same make.

S&F LED 9/10 Watt tube light fitting mirror intregated type, including LED retrofit tube lamp 9/10 W , LED tube light nominal power 9/10 Watt, L LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 115 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 extruded aluminium LED battens life span of minimum 50000 working hours complete fitting including connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fitting including taking down old unserviceable complete all as specified & directed. Note : Make of batten and LED tube lamp should be of same make.

S&F 18W - 1260lm - 6500K - CRI>80 Ra - Beam Angle 24° Slim Magnetic Track Light , Die Cast Aluminium & Polycarbonate Clear Diffuser with Lens Surface mounted with Magnetic Track Channel

S & F in repair LED street/security lights nominal power 35 Watt, LED of Make Osram; Everlight; Philips; Nicha; Cree; Samsung, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, lumen efficacy of minimum 110 lumens per watt, built-in integrated electronic LED driver, output open /short circuit protection, phase to phase protection, over voltage protection, surge voltage protection upto 4 KVs, protection grade IP 66, CRI greater than 80%, CW available CCT of 5700K, power factor of minimum 0.95, pressure die-cast aluminium alloy housing with epoxy powder coated metallic silver finish after phosphochromate treatment, life span of minimum 50000 working hours including fixing at any height and including wiring using three core PVC insulated, PVC sheathed, flexible stranded copper conductor FR-LSH cables suitable for outdoor use, 1.5 sqmm as per IS 694: 2010 complete all as specified and as directed.

supply and fixing ventilating metalic body exhaust fan 300 mm sweep 230 volt AC, heavy duty

S & F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 Amps rated busbar, Confirming to IS as per IEC 61439-3, 4 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 , IK 09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match as the existing with all as specified and directed by Engr-in-charge.

Supply and fixed MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Voltsand to be housed in DBs including necessry connection complete all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating) complete all as specified and directed..

Supply and fixed MCB SPN 32 Amps, 'C' curve, 240 Volts,ISI marked and to be housed in DBs complete including necessry connection all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating) complete all as specified and directed..

Supply and fixing soundless Ceiling fan of capacity 1200 mm, 240 volts, ISI mark, BEE rated 5 star Brushless direct current(BLDC) without remote including all connected items and accessories complete all as directed by Engr-In-Charge.

S&F of Magnetic track slim 2mtr track Recess Mounted with and including driver Extruded Aluminium with Black Powder Coated housing, internal track made of Copper Stick Mounted with PVC Strips and MSStrip for Magnet One Side Black Finish, Protection Class II complete all as specified and directed.

Material and labour for earthing complete with Galvanised steel earth plate electrode 600x600x6 mm mm buried directly in ground (Earth pit not less than 2.25m below ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to GI wire 4 mm as earth lead by means of bolt, nuts, check nuts and washers of galvanised iron or steel, upto 7.5m length, earth strip protected by and including 15 mm dia GI pipe (light grade) and connected to main test point or body of pole/pannel or lightening arrester of main controlling switch as directed including concrete pit in PCC (1:3:6) type C1 , Precast RCC (1:2:4) Type B1 cover slab of size 54x54x5 cm reinforced with 8 mm dia TMT bars @ 100 mm C/C both ways with one handle for lifting made out of 10 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm bore GI Pipe (Medium Grade) for watering, Charcoal and salt in alternate layers of 15 cm (Compacted Thickness) around the earth electrode including necessary excavation, earth work in any type of soil and disposal of spoil to a distance n.exc 50 m and necessary testing complete all as shown in Electrical Plate No 3 of SSR Part-I. NOTE : 1. The unit rare includes for protectionh GI pipe of 15mm and watering pipe of 20mm bore including excavation for earth pit in any type of soil/disintegrate rock. 2. Contractor has to bring agriculture soil from outside of defence land and fill in earth pit to acheive desired result as the soil resisitivity is very high. 3. The cost of GI wire including protection pipe, from top of earth plate upto 7.5 meter above/below ground level is deemed to be included in the unit rate. 4. All the joints in GI wire and connectgion with earth plate to be welded through brazing and in addition by providing double brass nut bolt and washer. 5.Costing of welding and nut bolts are deemed to be included in the unit rate

Supply, Laying and testing cable LT XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip armoured electric power cable heavy duty with solid aluminium conductor 1100 volt grade, laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,including brass cable glands,clamps,etc of 2 core 6 sqmm.

M&L Sand Cushioning (dry) in trenches for protection of UG Cables (below, above and around the UG Cable laid in Trenches) of 230mm Spread thickness and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. (NOTE : For the purpose of Payment, Punned thick-ness of Sand Cushioning only shall be Measured and Paid )

Supply and laying well burnt Bricks , locally available best quality (sub class "B" bricks) laid in trenches perpandicular to U/G cable for cable protection complete all as specified.

S & F rotational moulded polyethylene ISI marked (vertical cylindrical with close top) as per IS 12701: 1996 of 100 litres capacity water storage tank hoisted and fixed in position with and including Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for 25mm bore dia iron pipe, provision of 20 mm /25 mm dia medium grade GI pipe for connecting inlet, outlet, over flow and washout pipes including dismantling the existing one and removing to store complete all as specified and as directed.

Supply & fix 25mm bore GI tubing medium grade in trenches / Floor / pillar connetion in new postion including GI fittings all as specified & as directed .

Supply and fix 25 mm bore dia pipe gun metal globe or gate valves, yoke type, full opening with iron wheel head, screwed both ends heavy duty, ISI marked complete for iron pipes complete all as specified and directed.

M&L cutting existing steel tubing for alteration or addition of size 40 to 50mm dia GI pipe including necessary threading, oiling etc complete all as directed by EIC.

SPS TRADING (BID ID -3467018)

Intime Commotrade Pvt Ltd (BID ID -3466862)