SPECIAL REPAIR TO BLDG NO P-298 (COOK HOUSE) P-1229 P-1256 1290 AND P-1295 AT SRI GANGANAGAR MIL STN

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding and rubbish off the premises complete all as specified and directed by Engineer - in - Charge.

M&L glazed ceramic coloured tiles grade, (300x600)x7mm thick as on vertical surfaces like dados or skirting over 10mm thick rendering in CM 1:4, set & jointed in neat cement slurry and pointed in epoxy grout mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer - in - Charge.

Demolition of cement Concrete(un-renforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Roughning of surfaces of old concrete floor by picking,sweeping clean and washing down with water to remove dust etc.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exc 0.18 sqm laid in floor set and jointed in cement slurry including 15 mm thick screed bed or bedding layer of cement mortar 1:4 for laying floor finish even & fair and pointed in epoxy grout mixed with pigment to match the shade of tiles complete all as specified and directed.

M&L for 25 thick cement concrete flooring type B-0 1:2:4 (12.5 mm graded stone aggregate) complete all as specified and directed.

M&L for vitrified coloured tiles 8- 10mm thickness (square/rectangular) polished area of each tile 0.36 sqm(600mmx600mm) but n exc 0.42 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm th screed bed in CM 1:4 complete all as specified and as directed.

All as per item No 7 above but on skirting over 10 mm thick including rendering in CM 1:4 as in backing layers for tiles complete all as specified and as directed.

M&L for double charged vitrified ceramic light shade tiles 8-10mm thickness (square/rectangular) polished area of each tile 0.42 sqm(600mmx1200mm) but n exc 1.0 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm th screed bed in CM 1:4 complete all as specified and as directed.

All as per item No 9 above but on skirting over 8- 10 mm thick including rendering in CM 1:4 as in backing layer of tiles complete all as specified and as directed.

Demolition stone slabs of any description or thickness in floors, apron etc laid bedded and pointed in any mortar

M&L machine cut Kota stone flooring 18-20 mm thick over 20 mm thick screed base in cement 1:4, laid and jointed with grey cement slurry and pointed in epoxy grout mixed with pigments to match the shade of the slabs including rubbing, rounding of edges (moulding of edges) and polishing complete all as specified and directed by Engineer - in - Charge.

All as per above item No-12 but in vertical surfaces like dados or skirting over 10mm thick rendering in CM 1:4, set & jointed in neat cement slurry and pointed in epoxy grout mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer - in - Charge.

M&L for Z Black Telephonic granite (of any type) 20 mm thick machine cut, bedded & jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding, rounding of edges (moulding of edges) and polishing complete laid over and 15 mm thick screed bed in CM 1:4 etc all as specified and directed by Engineer in charge

Demolition of cement concrete of any description and in any position for sunken portion and floor all as specified and directed by Engr-in-charge.

M&L for PCC 1:5:10, type E-2 using 40 mm graded stone aggregate as filling of sunken floors complete all as specified and diredted by Engineer-in- charge..

Dimolition of Brick tiles or terracing tiles , single layer on roofs complete all as specified and directed.

Demolition of old mud phuska, removing rubbish of the premises cleaning surface and preparing to receive new concrete/cement plaster complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:2:4 type B1(20 mm graded stone aggregate) as in roof padding/kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed by Engineer in chgarge.

Provide and apply moisture insensitive primer @ 0.20-0.25 Kg/m2, Allow the primer to cure for 6-8 Hrs to tacky condition. Provide and appy 2 coats single component PU based cold applied seamless waterproofing membrane, coverage at the rate 2.3-2.5 Kg/m2 in 2-3 coats to achieve DFT of 1.5 mm. The PU membrane shall be determined 300mm above FFL, self-curing for 5 days. The Waterproofing material shall have solids > 85%, Tensile strength > 2 Mpa as per ASTM D 412, Elongation > 400% as per ASTM C 1305, crack bridging up to 2mm, Shore A Hardness >70 as per ASTM D 2240, Adhesion to concrete > 2Mpa as per ASTM D 903, Water vapor permeability>14gm / m2 / day as per ISO per ISO 9932:91, Puncture Resistance > 300 N as per, ASTM E154- 2013 Water Head Resistance 50M as per DIN 1048 complete all as specified and directed by Engr-in- charge. Make :- Fosroc /Sika/Bostic/Choksey Note :- (i) All above operations to be done by authorised applicator in order all as specified and directed. (ii) Auth company will submit confirmation of their Auth applicator before execution of Work.

S&F for Heat Resistant Terrace tiles (300mm X 300mm X 8-10mm) with SRI (solar refractive index) more than 78 on waterproof and sloped surface of terrace laid on 20mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio 1:1, including providing skirting upto 150mm height along the parapet walls in the same manner complete all as specified and directed by Engr-in- charge.

Dismantling water tank capacity exc 250 Ltr and n exc 1000 ltr complete all as specified and directed by Engineer - in - Charge.

S&F rotational moulded polyethylene water storage tank white colour 1000 ltrs capacity three layered (Cylindrical vertical with closed top) hoisted and fixed in position including 25mm bore PTMT ball valve, high pressure with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe or brass ferrule (minimum weight 455gms) complete all as specified and directed by Engineer - in - Charge.

S&F rotational moulded polyethylene water storage tank white colour 500 ltrs capacity three layered (Cylindrical vertical with closed top) hoisted and fixed in position including 20mm bore PTMT ball valve, high pressure with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe or brass ferrule (minimum weight 455gms) complete all as specified and directed by Engineer - in - Charge.

Taking down chowkhats or frames (without taking off shutters from the frames) not exceeding 1.5sqm each complete all as specified and directed by Engineer - in - Charge.

S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) abricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: 1. For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 2. Test certificate of manufacturer to be provided by contractor . 3. Embossing with barcode of manufacturer engraved over each door frame and shutter is manadatory. 4. M.S. hold fast/ lugs or SS dash fasteners deemed to be included in quoted rates.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. for fixing MosquitoMesh and XTN aluminium mesh combinely panel area of door except stiles and rails to be panelled wire mesh with self tapping round headed screws at requrd distance, scres and edge covered with feathered pvc edge beading all around mesh and fixing stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer in- Charge. (a) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long -2 nos per leaf (b) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x250mm - 1 nos per leaf (d) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos per leaf Note : 1: Test certificate of manufacturer to be provided by contractor . 2. Embossing with barcode of manufacturer engraved over each door frame and shutter is manadatory.

S & F factory made uPVC sliding window three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm) with or without provision of opening for cooler as directed including all fittings, steel roller system, locking arrangement etc., making arrangement for fixing of hardware, glass, wiremesh, grill etc all as per manufacture instruction and Drg No BTD-890/R . Note:- The unit rate quoted by contractor excludes cost of glass & wire mesh and includes all other connected accessories. Net Opening will be measured for payment purpose. Wire mesh and Glass Shall be measured and paid Seperatly .Provision of all other items as shown on DWgs & Cutting holes of suitable depth in wall for inserting lugs etc including making good dismantalled portion with PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggreegate and cement mortar (1:3) shall be deemed to be included Note :- 1. Description of items amend accordingly as per manufacturer instructions, 2. Test certificate of manufacturer to be provided by contractor . 3. Embossing with barcode of manufacturer engraved over each door frame and shutter is manadatory.

S & F factory made uPVC window or ventilator side hung/top hung (glazed and gauge both) made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm) including all fittings like hinges, tower blot, peg stay, locking arrangement etc., making arrangement for fixing of hardware all as per manufacture instruction and Drg No BTD-890/R all as specified and directed. Note: The unit rate quoted by contractor excludes cost of glass & wire mesh and includes all other connected accessories. Net Opening will be measured for payment purpose. Wire mesh and Glass Shall be measured and paid Seperatly. Provision of all other items as shown on DWgs & Cutting holes of suitable depth in wall for inserting lugs etc including making good dismantalled portion with PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggreegate and cement mortar (1:3) shall be deemed to be include. Note :- 1. Description of items amend accordingly as per manufacturer instructions, 2. Test certificate of manufacturer to be provided by contractor . 3. Embossing with barcode of manufacturer engraved over each door frame and shutter is manadatory.

M & L toughned glasss, figured glass ordinary quality 5 mm thick and glazing with oil putty in square n exc 0.50 Sqm in each panes fixed to steel, metal or wooden window frames complete as per directed by Engineer-in-charge.

M & L sheet Pin headed glass 4.0mm thick and glazing with oil putty in square n exc 0.50 Sqm in each panes fixed to steel, metal or wooden window frames complete all as specified.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and directed by Engineer - in - Charge.

S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and directed by Engineer - in - Charge.

S&F Aluminum Grill powder coated of approved design/pattern with aperture size 50 mm and wire dia 5 mm fixed with Aluminum Frame complete all as specified and directed by Engr-in-charge.

M&L for mild steel work as in frame work/guard bar for door and window and as similar work including cutting tops to shape, drilling holes, notching for wire etc conforming to Fe-290 grade E-165 complete all as specified and directed by Engineer - in - Charge.

M&L for Mild steel work as ISMB,joists channel,angle or tee section fixed adjacent to ceiling and embedding in floor and brickwork and making including cutting welding and the like including caps.bases,splices etc,built from one or more beam or channel section or angle with plates including all lattice bars, stiffeners,gusset plates including necessary welding,rivetting etc.confirming to Fe 410 (Gde E-250) quality A etc all as specified and directed by Engineer-in-charge.

Taking down chowkhats or frames (without taking off shutters from the frames) exceeding 1.5sqm but n.exc 4.0sqm each complete all as specified and directed by Engineer - in - Charge.

Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm each and removal from site complete all as specified and directed by Engineer - in - Charge.

Taking down wooden shutters only of any description area exceeding 1.0 sqm and not exceeding 2.0 sqm each and refixing in same opening after necessary easing, adjustments, minor repairs, oiling, adjustment with cutting or fixing plain fillets/planks made from second class hard wood etc to remove gap between floor and shutter complete all as specified and as directed by Engineer-in- charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners deemed to be included in quoted rates.)

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners deemed to be included in quoted rates)

M & L for applying two coats of synthetic enamel paint (ordinary tint) over one coat of red oxide primer on new steel surface over 10 cm width or girth, not otherwise described including preparation of surface complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of old steel painted surfaces including as knotting, stopping, Burning off or removing, scraping etc,and then applying two coat of synthetic enamel paint (ordinary tint) on steel surfaces 10cm width or girth complete all as specified and directed by Engineer - in - Charge.

Supply & fixing Factory made prefabricated Pressed steel Door frame made out of mild steel 1.25mm thick girth of frame 185mm including necessary MS rawl plug/bolts and fixing 75mm long butt hinges medium weight cold rolled mild steel etc and shutter including stiffeners made out of mild steel sheet 1.25mm thick cut to size, holes punched and welded seams including bending or turning up all around, mitred angle etc as required with Locking arrangement using mild steel mortise lock 4 levers with 2 Nos of keys of size 100mm including MS chromium plated handle and 2 Nos MS locking rods out of 8 mm dia not exc 1000mm long fixed to mortise lock and handle with necessary bolts and nuts covered by MS sheet 1.25 mm thick complete including two coat of synthetic enamel paint over a shop coat of zinc chromate primer on interior surface (not -visible from front) and hammer tone paint on exterior surface ( visible from front) as per Godrej Pattern complete all as specified and as directed by Engineer-in-charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative type glazed/guage skeleton door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus ofelasticity 850 N/mm2 and resistance to spread of flameof Class A category with property of being termite/borerproof, water/moisture proof and fire retardant and fixingwith stainless steel butt hinges of required size withnecessary full body threaded star headed counter sunk S.S screws,including s&f of stainless steel steel 304 grade (natural finish) wire cloth , all as per direction of Engineer-In-Charge.including S&F including following items:- Note: (a) stainless steel(304 grade) finished butt hinges 100mm -04 Nos per leaf (b) Stainless steel (304 grade ) finished square tower bolt 200mm long -02 Nos per leaf (c) Stainless steel (304 grade) finished handles 200mm -02 Nos per leaf (d) Stainless steel (304 grade) finishedsliding door bolt 300mm -01 Nos per leaf (e) Stainless steel (304 grade) finished floor door stopper -01 Nos per leaf (f) Stainless steel (304 grade) wire cloth fixing as per manufacture. (g) Test certificate of manufacturer to be provided by contractor . (h) Embossing with barcode of manufacturer engraved over each door frame and shutter is manadatory.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus ofelasticity 850 N/mm2 and resistance to spread of flameof Class A category with property of being termite/borerproof, water/moisture proof and fire retardant and fixingwith stainless steel butt hinges of required size withnecessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge Note: (a) stainless steel(304 grade) finished butt hinges 100mm -04 Nos per leaf (b) Stainless steel (304 grade ) finished square tower bolt 200mm long -02 Nos per leaf (c) Stainless steel (304 grade) finished handles 200mm -02 Nos per leaf (d) Stainless steel (304 grade) finished sliding door bolt 300mm -01 Nos per leaf (e) Stainless steel (304 grade ) finished floor door stopper -01 Nos per leaf (f) Test certificate of manufacturer to be provided by contractor . (g) Embossing with barcode of manufacturer engraved over each door frame and shutter is manadatory.

Dismentling of boarding any description fixed in any position with nails/ screws complete all as specified

S&F continuous (piano) hinges 20mm & 12 MM width of flap, mild steel bright finish or electrogalvanised of complete all as specified

S & F hasp and staple, safety type of aluminium anodised100mm size fixed with screw complete all as specified and directed by Engineer - in - Charge

S&F 25 mm size magnetic catches with Plastic body and striking plate including letting in and fixed complete

S&F stainless steel handles, 150 mm long complete all as specified and directed. (back plate staple D type)

Supply & fixing 18mm thick Plywood, grade BWR, type BB, fixed with screws to frame work along with one side laminate and other side plain white 0.9mm thick type-I, colour pattern as approved including PVC lipping, PVC sheet is heat bent as lipping on the edges of doors complete all as specified and as directed by Engineer-in-charge.

S&F second class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed to shelves support complete all as specified and directed by Engineer-in-charge.

M & L for applying two coat of synthetic enamel paint on old wood and wood based surfaces of any description, over 10cm width or girth, not other wise described including preparation of old painted surfaces

S&Fin repairs 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed by Engineer - in - Charge.

S&F 300 mm mild steel sliding door bolts, clip type, stone enameled block with bright bolt not less than 12mm dia with and incl a minimum of 6 bolts and nuts, 4 on bolt plate 2 on staple plate complete all as specified and directed by Engineer - in - Charge.

S&F in repair 300 mm mild steel sliding door bolts, clip type, stone enameled block with bright bolt not less than 12mm dia with and incl a minimum of 6 bolts and nuts, 4 on bolt plate 2 on staple plate complete all as specified and directed by Engineer - in - Charge.

S&F in repairs aluminium handle, 150mm size, cast type, anodized (ISI marked) complete all as specified.(D type Handle and back side staple)

S&F in repair 15 mm dia chromium plated concealed type stop valves, cast copper aloy with crutch or butterfly handles screwed down high pressure, screwed both ends for iron and fixed complete all as specified and directed by Engineer - in - Charge.

S&F in repairs, Angle valves, chromium plated cast screwed down, high pressure copper alloy, with crutch or butterfly handles, screwed both ends for but fancy type 15mm bore iron pipe or complete all as specified and directed by Engineer - in - Charge.

S&F in repairs chromium plated shower rose of any colour with or without swivel joints 125mm square size including shower arm complete all as specified & directed by Engineer in charge.

S&F single liver High flow diverter consisting of exposed parts kit with operating lever, wall flange & button and concealed body , cartidge sleeve and also including bath spout with wall flange chromium plated, screwed down, high pressure all as specified. Make : Cera (exposed part F1020721,concealed part F4030101, Bath spout F1020661) ,Jaquar / Kohler or equivalent as approved by GE.

S&F Brass CP wall Mixer for mixing hot and cold water screwed down for iron pipe and fied complete all as specified and directed by Engineer - in - Charge. Make: Cat No T4635A1 of Claret Collection of Parryware / Jaquar / Cera/ Kohler.

S&F Brass CP basin mixer for mixing hot and cold water screwed down for iron pipe and fied complete all as specified and directed by Engineer - in - Charge.

S&F health faucet to EWC ,CP brass with minimum 1000mm long CP flexible pipe, connection etc., complete all as specified and directed by Engineer - in - Charge.

S&F toilet paper holder, brass chromium plated fixed to walls with chromium plated (CP) brass screws complete all as specified and directed by Engineer - in - Charge.

S&F corner wash hand basin of size 450 x 390 mm vitrous China white flat back including brackets, waste coupling & PVC waste pipe of 32 mm dia etc. complete all as specified and directed by Engineer - in - Charge.

S&F in repairs SS soap dish of any size fixed with screws complete all as specified and directed by Engineer in charge.

S&F Stainless Steel grating 125mm dia with waste hole (Minimium weight 40 grams) complete all as specified and directed by Engineer - in - Charge.

S&F in repairs grating doom 100 mm dia of stailess steel with and without hole complete all as specified and directed by Engineer vin charge.

S & F in repair stainless steel tubular towel rail 20mm dia “D” type 60 cm long between flanges including brackets complete all as specified and directed by Engineer - in - Charge.

S&F glass corner self assembly, fancy type, made of 5 mm thick sheet toughened glass of size 250x250mm, fixed with CP brackets, complete all as specified and directed by Engineer - in - Charge.

S&F 5 mm thick and 600mm long & 250mm width glass shelves fancy type and fixed over CP brass brackets all as specified and directed by Engineer-in-charge.

S & F in repair stainless steel towel ring min 30mm dia including brackets complete all as specified and directed by Engineer - in - Charge.

S&F in repairs fancy type long body bib taps,15 mm cast copper alloy, with crutch or butterfly handles, screwed down, screwed for iron pipe or brass ferrule for 15mm bore complete all as specified and directed by Engineer - in - Charge.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed by Engineer - in - Charge.

S&F in repair water closet vitreous china squatting pan "Orrisa pattern" size 580mmx440mm white with integral foot rests (Excl flushing cistern) including all joints and making good to the floor complete all as specified including CI 'P' trap/S trap all as specified and directed by Engr-in-charge.

S&F in repairs, PVC low level flushing cistern 10 lirs capacity, valve-less, syphonic action type, white, with inlet, ball valve, float, and handle including brackets, PVC connections 15 mm size with PTMT nuts of length 450 mm ,including 32mm bore flush pipe of polyethylene of low or high density of PVC complete all as specified and directed by Engineer - in - Charge.

S&F, in repair vitreous china wash hand basin, white flat back of size 550mmx400mm including brackets, 32mm bore brass chromimum plated waste coupling & 32mm bore low density ployethylene (LDPE) flush pipe of pressure rating 6Kgf/Sq cm (1.00 M long) complete, including 15mm bore 450 mm length PVC connection with PTMT nuts.

S&F in repairs low density polyethylene pipes (LDPE) 32 mm dia and 1000 mm long of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors complete all as specified and directed by Engineer in charge.

S & F fancy type swan neck pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure of 15 mm bore diawith or without lettered Hot or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer in charge.

Dismantling of 100mm dia cast iron, PVC or reinforced concrete pipes jointed in cement mortar and taking out of trenches, if required all as directed by Engr-in-charge following bore of pipe

Dismantling of 75mm dia cast iron, PVC or reinforced concrete pipes jointed in cement mortar and taking out of trenches, if required all as directed by Engr-in-charge

Supply & fixing 75mm bore uPVC pipes grade 'B' single socketed in any length with rubber ring joints, fixed along walls with and including suitable size clamps/brackets (interval of 1m and pipe keeping 100mm away from wall ) fixed with fasteners/nut bolts, joints fixed with pipe joint lubricant complete all as specified and as directed by Engineer-in- charge. Note:- Bracket, clamp, nut bolt, fastner, slotted channel etc shall be made of deep drawn low carbon steel material with hot dip zinc aluminium flake coated and fixed all as shown on BTD drawing cost for same shall deemed to be included in the quoted unit rate and nothing extra shall be admissible on this account.

Supply & fixing 110 mm bore uPVC pipes grade 'B' single socketed in any length with rubber ring joints, fixed along walls with and including suitable size clamps/brackets (interval of 1m and pipe keeping 100mm away from wall ) fixed with fasteners/nut bolts, joints fixed with pipe joint lubricant complete all as specified and as directed by Engineer-in- charge. Note:- Bracket, clamp, nut bolt, fastner, slotted channel etc shall be made of deep drawn low carbon steel material with hot dip zinc aluminium flake coated and fixed all as shown on BTD drawing cost for same shall deemed to be included in the quoted unit rate and nothing extra shall be admissible on this account

S&F of 110mm dia PVC junction single 'Tee' ISI marked jointed with solvent cement fixed in walls and the dia of pipes complete all as specified and directed by Engineer - in - Charge.

S&F of 110mm dia uPVC bend equal ISI marked jointed with solvent cement fixed in walls and the dia of pipes complete all as specified and directed by Engineer - in - Charge.

All as per srl item No. 87 here-in-before but size of 75mm dia complete all as specified and directed by Engineer - in - Charge.

M&L uPVC (SWR) 75 mm P Trap complete all as specified and directed by Engineer-in-Charge.

Taking down eaves gutters and rain water pipes (any size or pattern) including all fittings, heads, shoes, bends, swan – necks, etc. including cleaning of any description complete all as specified and directed by Engineer - in - Charge.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed by Engineer - in - Charge.

S & F 75 mm bore of pipe PVC (SWR) bends of any radius / shoe fixed to PVC pipes complete all as specified and directed by Engineer - in - Charge.

M&L uPVC junction 110 mm branch piece equal or unqual complete all as specified and directed by Engineer-in-Charge.

M&L uPVC branch pieces, 75 mm bore, (equal or unqual), complete all as specified and directed by Engineer-in-Charge.

M&L uPVC junction 110 mm (Single T), equal or unqual complete all as specified and directed by Engineer-in-Charge.

Taking up or down for 15 mm bore steel water tubing galvanised with connection including cleaning for refixing complete all as specified and directed by Engineer - in - Charge.

Taking up or down for 20mm bore steel water tubing galvanised with connection including cleaning for refixing complete all as specified and directed by Engineer - in - Charge.

Taking up or down for 25mm bore steel water tubing galvanised with connection including cleaning for refixing complete all as specified and directed by Engineer - in - Charge.

S&F CPVC ISI SDR 11 pipes 20 mm dia with all fitting, including all Brass Fitting and fixed to walls & ceilings or laid in floors, bore of pipe 20 mm complete all as specified

S&F CPVC ISI SDR 11 pipes 25 mm dia with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 25 mm complete all as specified

S&F CPVC ISI SDR 11 pipes 32 mm dia with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 32 mm complete all as specified

S&F hat pegs and hooks (cloth hanger with five peg set each) complete all as specified and directed by Engineer - in - Charge.

S&F in repairs Vitreous china premium/1st quality wash down water closet wall hung EWC white (closed pattern incl all necessary like rag bolts/gel gasket, PVC (SWR) WC connector benty type etc.) Plastic water closet soft slim seat cover, white, closed pattern with flat bottom, and cover with aluminised hinging device complete all as specified and as directed. Make :- Model No. S1043171 of Cera / Jaquar / Parryware / Kohler / Hindware

S&F in repairs concealed cistern set with full frame compatible with wall hung type water closet complete all as specified and drected by engineer in charge. Make: Cat No B1190104, B1190105, B1190106, B1190107 Cera / Jaquar / Parryware / Hindware / Kohler

S&F Harrison rails mild steel chromium plated with fixing brackets, stops, rollers etc 20mm bore dia complete all as specified and directed by engr-in-charge.

M&L for 75mm thick Cement concrete type C-2 , 1:3:6 (40 mm graded aggregate) as in plinth protection laid in bay n.exc 2.5m length complete all as specified and directed by Engineer - in - Charge.

Demolition of RCC as in Roofs, floors ( other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed by Engineer - in - Charge.

Demolition of brick work built in cement mortar of any description complete all as specified and directed by Engineer - in - Charge.

M&L brick work with sub class 'B' Bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 complete all as specified and directed by Engineer - in - Charge.

M&L half brick work with sub class B bricks straight or curved on plan exceeding 6 mtr mean radius in cm 1:6 etc.complete all as specified and directed by Engineer - in - Charge.

M&L Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick (horizontal or sloping) complete all as specified and directed by Engineer - in - Charge.

Form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide rough finished complete all as specified and as directed by Engineer-in- charge.

M&L for RCC nominal mix 1:1 1/2: 3 (using 20mm graded stone aggregate ) as in slabs suppotred on walls, beams and columns complete all as specified and directed by Engineer - in - Charge.

S & F for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia complete all as specified and directed by Engineer - in - Charge.

Taking down cement plaster of amy description on bricks or concrete surfaces of walls including racking out joints, hacking for keys scrubbing down with water etc. complete all as specified directed by Engr-in-Charge.

M&L 15mm thick, rendering in cement mortar 1:6 to brick/concrete wall surfaces finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L 15mm thick, rendering in cement mortar CM 1:4 to brick/concrete wall surfaces in two layers first layer 10mm thick and second layer 5mm thick with WPC 3% by wt of cement finished even & smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L 5mm thick, rendering in cement mortar 1:3 to ceiling surfaces on patches finished even and smooth without using extra cement in patches complete all as specified and directed by Engr-in-Charge.

M&L for prepration of New plastered Internal wall surface complete applying the following :- (a) Applying two coat 1.5 mm wall care putty on wall surface and smoothening the surface with sand papers / Mechanised sanding etc prepatory to paint as directed coomplete all as specified (b) Applying one coat of internal Wall Primer by using Roller over complete all as specified (c) Applying two coat of interior Apcolite Premium Emulsion Roller over complete all as specified Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible

M&L for prepration of New plastered ceiling surface complete applying the following :- (a) M&L 1.5 mm wall care putty in two coats on ceiling surface and smoothening the surface with sand papers / Mechanised sanding etc prepatory to paint as directed complete all as specified. (b) M&L two coat of interior acrylic emulsion over a coat of chalk whitening priming by using Airless spray / Roller over complete all as specified .

M&L for prepration of New plastered External wall surface complete applying the following :- (a) Applying two coat 1.5 mm wall care putty on wall surface and smoothening the surface with sand papers / Mechanised sanding etc prepatory to paint as directedcoomplete all as specified (b) Applying one coat of Exterior Wall Primer by using Roller over complete all as specified (c) Applying two coat of Apex Advcanced Dust Proof Emulsion using Roller over complete all as specified Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible

M&L for complete removal of existing treatment including filling depression of scraped surface (a) Applying one coat wall care putty 115mm thick on wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directedcoomplete all as specified (b) Applying one coat of internal Wall Primer by using Roller over complete all as specified (c) Applying two coat of interior Apcolite Premium Emulsion Roller over complete all as specified Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible

M&L two coat of Acrylic emulsion on old pastered ceiling surfaces over and including one coat of wall care putty(1.5mm thick) with complete removal of existing treatment of ceiling surface complete all as specified and directed by Engineer - in - Charge

M&L for complete removal of existing treatment including filling depression of scraped surface on Old external wall surfaces (a) Applying one coat 1.5 mm wall care putty on wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directedcoomplete all as specified (b) Applying one coat of Exterior Wall Primer by using Roller over complete all as specified (c) Applying two coat of Apex Advcanced Dust Proof Emulsion using Roller over complete all as specified Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible

M&L for Obliterating old writing of any description, n exc 0.1 sq. m, with paint to match existing work etc complete all as specified and directed by Engineer - in - Charge.

M&L for Writing letters or figures with fluorecent paint ( Block. Roman, Italic or Indian) n exc. 30 cm high etc complete all as specified and directed by Engineer - in - Charge.

S&F 25 mm bore gate valve with handle, screwed both ends for inlet & outlet pipe and fixed complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth. In brick walls complete all as specified and directed by Engineer - in - Charge.

M&L for welding in repairs Thickness of metal to be welded will be Exc 9 mm but not exc 20mm complete all as specified and directed by Engineer - in - Charge.

Cutting holes in brick walls built in cement mortar including making good dismantled portion in CM (1:3) or cement concrete (1:2:4) type B-1 exc half brick but n.exc one brick complete all as specified and directed by Engineer - in - Charge.

S&F GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists etc. in walls ceilings stanchions, beams etc. including all laps, cutting and waste as per specified and directed by Engineer-in-Charge.

S&F in repair fancy type SS curtain rod 25 mm dia with brackets knob rings(20 cm c/c) etc complete all as specified and directed by Engineer - in - Charge.

M&L for 75mm thick Cement concrete type D-2 , 1:4:8 (40 mm graded stone aggregate) as in sub base of floor all as specified and directed.

M&L precast machine pressed rubber moulded coloured concrete interlocking paver blocks any shape and sizeconfirming to IS 15658-2006 of 60 mm thickness, M -35 grade,set,jointed & pointed in neat cement slurry in floor/pavings/path etc with grey cement and pigment including 25mm thick sand cushioning complete all as specified and directed by Engineer - in - Charge.

M&L providing precast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in block masonry with solid blocks exceeding 10 cm width and setting as in kerb stone complete all as specified and directed by Engineer-in-Charge.

M&L Chequered cement concrete tiles with grey cement and no pigments 20cmx20cmx25 mm thick, set , jointed and pointed in neat cement slurry in floors including Screed bed or bedding layer of mortar 15 mmt hick in CM 1:4 for laying floor finishes complete all as specified and directed by Engineer - in - Charge.

Dismantling wall & ceilling boards(fibre pulp insulation etc) or insulation boards/ slabs/blankets, any thickness including cover fillets complete all as specified and directed by Engineer - in - Charge.

S&F for Hangers 3mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long as in hook and expansion hold fasteners 12.5mm dia 40mm long complete all as specified.

Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate

Providing and fixing 12mm thick Seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish (Frame work for ceiling shall be measured and paid separately) complete all as specified and directed. Note :- Design of ceiling approved by GE

Dismantling of Plain or corrugated/ semicorrugated steel sheeting, any guage, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed by Engineer - in - Charge.

Dismantling of wrought iron or mild steel work any description and fixed in any position complete all as specified and directed by Engineer - in - Charge.

M &L for MS work as in wind tie for roof including securing bolt or any other work incl cutting, drilling holes and similar works conforming to Fe 290 Gde e-165 etc complete all as specified and directed by Engineer - in - Charge.

S&F tee,angles,channel or flat section including distances cleats for roof trusses (framed),trussed,purlinn,crane gantries,rails and fastening and heavy brackets framing etc conforming to Fe 410-W(Gde-E-250) complete all as specified and directed by Engr-in-charge.

S & F Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws complete all as per manufactures instructions with all fittings and accessories etc complete all as specified and directed by Engineer - in - Charge.

Taking down and refixing of aluminium partition board with glass,rubber and aluminium beading and necessry accessories complete all as specified and directed by Engineer-in-charge. (Note: Contractor will pay for any damage during taking down and refixing of aluminium partition board .)

Material and labour for water proofing treatment to RCC sunken slab and adjoining vertical slab as described following any one complete as per dirns of GE. Note :- Plan area only measured of toilets for payment purpose. Method (A) Supplying and applying two component elastomeric acrylic polymer modified cementitious waterproofing coating, Smart Care Damp proof 2K, having 100% elongation as per ASTMD412, resisting 5 bars hydrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per DIN 1048, crack bridging upto 1.2mm as per ASTM 4548.5 clean all working surface and made free from dirt, grease laitance etc. After inspection for all working area ough surface, cracks and construction joints are treated by polymer modified mortar 1:4:4(1 Cement: 1Polymer: 4 Sand). Making Gola of size 75 x 75m at junction of vertical & horizontal with the polymer modified mortar of 1:1:4 (1 cement : 1 Polymer : Sand ). The coating shall be 2 parts of powder and 1 part of liquid without any water addition in he mixing and shall have consumption of 1.5Kg/Sqm per coat, etc, complete as per manufacturers specifications. (B) Bore packing:- All the borehole gaps between concrete surface and PVC pipe of various surface of various dia upto the neck of lvel of shall be filled with non-shrink free grout. – Smart Care GP Grout having dual shrinkage compensation property. Before the bore packing, surface of the PVC pipe and concrete surface will be made rough and sand sand will be sprinkled with polymer bonding agent. (C) Apply 12-15mm plaster on slab and vertical surface admixed with water proofing compound @200ml per bag of cement before treatment.

Material and labour for water proofing treatment to walls surfaces of toilets/baths/WC's (1600mm in toilet and 2100mm in bathroom on vertical wall surface) with following applications complete all as specified and as directed by Engineer-in-Charge :- (a) Applying first coat of chemical on cleaned surfaces @ 0.86 Kg/Sqm (Minimum) and drying for 24 Hours (b) Applying second coat of chemical @ 0.86 Kg/Sqm (minimum) over first coat.

Supply only Water proofing compound complete all as specified and directed by Engineer - in - Charge.

M&L 40 mm GI pipe medium grade, made to shape as in spout pipe in sunken/ verandah/ Balcony complete all as specified

Providing & Applying corrosion resistance single component, Polimer modified cement mortar to patch up the damaged concrete section in planks of 25mm thickness. Providing and applying corrosion resistance single component, polimer modified, fibre reinforced cementitious repair mortar having water powder ratio in the range of 0.12-0.14 and the mixed density of around 2300+50 kg/m3. The repair mortar shall achieve a minimum compressive strength of 60 N/mm2 @ 7days when tested as per BS :6319: Part 2 and a flexural strength of 19 N/mm2 when tested as per BS :6319 part 3. It shall achieve a minimum adhesionb bond strength of 5 N/mm2 when test on standard electometer as per ASTM C 881 . The tensile strength shall be a minimum of 6N/mm2 when tested as per BS6319: part7. Make: Sika-Sikadur 32LP/Fosroc-Nitobond SBR(EP)/Pidilite Dr Fixit Super Latex(EP), Asian paint repair polymer or Techno commercial equivalent make approved by GE in writing from E-in-C branch approved list height upto as per site complete all as specified and directed.

Supply for Pipe supporting clamping - single pipe of dia 110mm(4'') down take pipe fixing done with clamping system consists of profile bracket+continuous slotted C channel +U bolt rubber sleeve mounted system running vertically with wall distance 75mm (3'') pipe support clamping made of : 1. Profile bracket having wall distance 75mm(3'') made of low carbon Hot roll guage corrected oil pickled and drawn(HROPD) Steel (IS 1079): material size 32mm X3mm with ribbs and notch are hot dip galvanized+ Zn Al flake coated having salt spray test(test method-ASTM B-117-2019) results 2000hrs with SS304 Hex flange bolt with serration 5/16x3/4 (A/F 13mm) as per DIN 6921 and SS304 Hex flange nut BSW 5/16X18X8X13 with serration as per DIN 6923 .2. Continuous slotted "C' Channel with ribs to be used of size 250mm (10'') made of low carbon hot roll guage corrected oil pickled and drawn(HROPD) sTEEL (is 1079) are hot dip galvanized+Zn Al flake coated with material thickness of 3mm. 3. U bolt rubber sleeve mounted are made of low carbon mild steel with rod diameter 7mm approx: Zn Al flake coated with noise absorbing semitransparent ribbed silicon rubber sleeve; with Hex flange nut BSW5/16X18X8X13 with serration set as per DIN 6923-Zn Al flake coated.Hotdip galvanizing: as per IS 2629(1985)-610grams/m2(>85 microns). Material grade: IS 1079 used as per MTC confirms to EN 10204 3.1. Material qty: for one unit: 1. Profile bracket wall distance 75mm(3'')-02 Nos. 2. Continuous slotted C channel of size 250mm(10"). 3. U bolt rubber sleeve mounted for 110mm(4")CI or PVC pipe dia-01 No: and 4. Fixing nail Zn coated of thickness 6.5mm and length 63mm(2.5'')-04Nos. Fixing detail: Pipe support clamping unit to be fixed at every metre distance in the duct as specified in Chief Engineer Bathinda ZoneTechnical drawing(TD) of factory made pipe supporting system:DRG NO-BTD-916.

Supply for Pipe supporting clamping - single pipe of dia 75mm(3'') down take pipe fixing done with clamping system consists of profile bracket+continuous slotted C channel +U bolt rubber sleeve mounted system running vertically with wall distance 75mm (3'') pipe support clamping made of : 1. Profile bracket having wall distance 75mm(3'') made of low carbon Hot roll guage corrected oil pickled and drawn(HROPD) Steel (IS 1079): material size 32mm X3mm with ribbs and notch are hot dip galvanized+ Zn Al flake coated having salt spray test(test method-ASTM B-117-2019) results 2000hrs with SS304 Hex flange bolt with serration 5/16x3/4 (A/F 13mm) as per DIN 6921 and SS304 Hex flange nut BSW 5/16X18X8X13 with serration as per DIN 6923 .2. Continuous slotted "C' Channel with ribs to be used of size 250mm (10'') made of low carbon hot roll guage corrected oil pickled and drawn(HROPD) sTEEL (is 1079) are hot dip galvanized+Zn Al flake coated with material thickness of 3mm. 3. U bolt rubber sleeve mounted are made of low carbon mild steel with rod diameter 7mm approx: Zn Al flake coated with noise absorbing semitransparent ribbed silicon rubber sleeve; with Hex flange nut BSW5/16X18X8X13 with serration set as per DIN 6923-Zn Al flake coated.Hotdip galvanizing: as per IS 2629(1985)-610grams/m2(>85 microns). Material grade: IS 1079 used as per MTC confirms to EN 10204 3.1. Material qty: for one unit: 1. Profile bracket wall distance 75mm(3'')-02 Nos. 2. Continuous slotted C channel of size 250mm(10"). 3. U bolt rubber sleeve mounted for 110mm(4")CI or PVC pipe dia-01 No: and 4. Fixing nail Zn coated of thickness 6.5mm and length 63mm(2.5'')-04Nos. Fixing detail: Pipe support clamping unit to be fixed at every metre distance in the duct as specified in Chief Engineer Bathinda ZoneTechnical drawing(TD) of factory made pipe supporting system:DRG NO-BTD-916.

Taking down carefully aluminium point wiring (light, fan, socket or power, bell complete fitting such as sockets, ceiling roses, pendants, batten holders, regulators and making good the disturbed surfaces of wall, floors, ceiling in CM 1:3 etc complete all as specified and directed by Engineer - in - Charge.

M & L for concealed conduit point wiring complete for light/ fan on independent /combine board with cable 2.5 sqmm (Nominal area) FRLSH PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC Concealed conduit pipe medium grade 20 mm dia, pipe hooks , elbows, juction covers and junction boxes , after cutting in wall chasing for conduits and sinking's for modular metal flush boxes suitable length and Min 1.6 mm thickness, Min 51 mm depth for mounting, switches, sockets,fan regulator with modular cover plate with frame and making the good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth continuity conductor along with point wiring of 1.5 sqmm copper PVC insulated cable for one light/ fan point controlled by one switch and connected to common earth dolly, complete all as specified and direced by the Engineer in charge.

All as per Srl item No -157 here in before but for one switch socket combination 5/6 amp on independent board complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No -157 here in before but for one three pin socket outlet 5 Amp on same board with other switches complete all as specified and directed by Engineer - in - Charge.

All as per Srl item No. 157 here in before but for one switch socket combinationt 6 pin 5/ 15 Amps on independent board with copper conductor 2.5 Sqmm complete all as specified and directed by Engineer - in - Charge.

All as Srl item No. 157 here in before but for one light point controlled by two 2 ways switches with cable 1.5 Sqmm size complete all as specified and directed by Engineer - in - Charge.

All as Srl item No. 157 here in before but for call bell point complete all as specified and directed by Engineer - in - Charge.

S&F switch piano flush type single pole one way 5/6 Amps, 230 volts complete all as specified & directed by Engineer-in- charge.

S&F Switch socket combination 2 in 1, 5 pin, 5/6 Amps, flush type complete all as specified & directed by Engineer-in-Charge.

S&F Switch socket combination 2 in 1, 6 pin, 15/16 Amps, flush type complete all as specified & directed by Engineer-in-Charge.

S&F switch piano flush type single pole two way 5/6 Amps, 230 volts complete all as specified & directed by Engineer-in- charge.

SS&F socket outlet two-in-one, 3 pin, 5 Amp flush type complete all as specified & directed by Engineer-in- charge.

S&F bell push 5/6 Amps 230 V AC complete all as specified and directed by Engineer - in - Charge.

S & F modular switch 5/6 Amps single pole two ways complete all as specified and directed by Engineer – in - Charge.

S & F in replacement modular switch 5/6 Amps single pole one way,one module including modular cover plate with frame and metal flush box complete all as specified and directed by Engineer - in - Charge.

S & F modular Socket, 16A - 2/3 pin combined 2 Module complete all as specified and directed by Engineer - in - Charge.

S & F in repair modular socket 5 pin, type 5/6 Amps5 in 1 flush type 2 modular complete all as specified and directed by Engineer - in - Charge.

S & F in repair Modular switch 1 way 16A, complete all as specified and directed by Engineer - in - Charge.

Supply and fix in industrial socket metal clad plug and socket with MCBs single pole 20 Amp complte all as specified and directed by Engineer - in - Charge.

S&F ceiling rose polycarbonate surface bakelite 65 x 50mm size three terminals complete all as specified and directed by Engineer-in-Charge.

S & F in repair compact & decorative energy efficient LED mirror light fitting with antiglare diffuser and decorative end caps suitable for 1X10 watt fitting 2 ft version including LED lamp 10 watt complete all as specified. (Make : Havells cat part no LUMILINEPLUSBS10WLED865SPCSS, Bajaj cat part no. BCLSB 10 WH, Crompton cat part no. LDL-10-CDL)

S & F stepped type, fan Modular regulator not less than 120 watt for ceiling fan 1200/1400mm sweep complete all as specified and directed by Engineer - in - Charge

S&F Buzzer AC 230 single poleVolt ding dong type complete all as specified and directed by Engineer - in - Charge.

S & F in replacement of existing light fitting with LED batten 20 W LED batten with 'Eye Soft' technology & glarefree diffuser for perfect application in modern homes or aliminium housing and integrated electronic driver, 20 watt, 50 Hz , 6500K, and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connector complete all as specified and directed by Engineer - in - Charge.

S&F in replacement security light fitting LED TYPE 25 watt with all necessary acessories, Clear transparent acrylic cover, prewire suitable to operated on 230 volt 50 HZ AC & Supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe “light grade” brackets 2 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed by Engineer - in - Charge

S&F in replacement recess mounting 2 x 2 feet 36 watt LED luminaire with powder coated CRCA housing with LEDs, seamless front from frame with high transmission acrylic cover and fixed electronic driver (surge protector) complete all as specified and directed by Engineer - in - Charge.

S & F Water tight bulk head fitting (New pattern),comprision of connector, weather proof enamelled gallery ,including 10 watt LED llight with separate driver all as specified and directed by Engineer - in - Charge.

S & F decorative wall light fixture made up of polycarbonate, suitable for 9W retrofit LED lamp B22 base three core flexible copper conductor cable of suitable size all as specified and directed by Engineer - in - Charge.

S & F in replacement angle holder insulated body with back plate for conduit fittings complete all as specified and directed by Engineer - in - Charge

S&F LED lamp 9W for angle holder complete all as specified and directed by Engineer - in - Charge.

S & F in replacement of sub-main wiring with two single core cables PVC insulated and un-sheathed 6 sqmm (Nominal Area) FRLSH stranded copper conductor drawn in concealed PVC conduict dia 20mm “medium quality” conduit including 6.00 Sq mm (Nominal Area) copper cable as earth continuity conductor after chasing in wall and making good the disturbed surfaces and white wash or existing colour , necessary junction box and covers including necessary connections, PVC flexible pipes are used in pannel board while connecting the cable complete all as specified and directed by Engineer - in - Charge. Note : Two run of wire, one run of earth wire and conduit shall be measured as one unit.

S & F in replacement of sub-main wiring with two single core cables PVC insulated and un-sheathed 4 sqmm (Nominal Area) FRLSH stranded copper conductor drawn in concealed PVC conduict dia 20mm “medium quality” conduit including 4.00 Sq mm (Nominal Area) copper cable as earth continuity conductor after chasing in wall and making good the disturbed surfaces and white wash or existing colour , necessary junction box and covers including necessary connections, PVC flexible pipes are used in pannel board while connecting the cable complete all as specified and directed by Engineer - in - Charge. Note : Two run of wire, one run of earth wire and conduit shall be measured as one unit.

Supply, fixing, testing & commissioning of electric chimney (90cm) with feature of baffle filter, inbuilt light, touch sensor screen control panel, noise level 58 dB, stainless steel body, air suction capacity 12CMH, speed level 3, motor power 180 watt, input vol 220-240 V/50Hz remote controlled and fitting in wall as concealed or duct complete all as specified and directed by Engr-in-Charge.

Supply, fixing, of MS powder coated fly catchers machine with dimensions (L 24.5"x D 5.5"x H 17"), light source philips actinic UV tubes (two tubes), capacity of 18 watt each of tube complete all as specified and directed by Engr-in-Charge.

S&F in replacement Sheet metal enclouser for doble door Vertical DBs made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mouting VTPN 4 Way 415 Volt ISI marked 250Amps busbar stove enameled dust and vermin proof,IP:43 protection suitable for incorporation FP MCCB(V-Tech) N3 Frame upto 125A ,Isolators and including give connection with wire and cable etc complete all as specified and directed by Engineer-in-Charge.

S & F in replacement sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 8 ways, 240 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S & F in replacement sheet metal enclosure for double door DB made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 12 ways, 240 Volts, ISI marked 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S&F in repairs MCCB TP&N pole 63 Amps with breaking capcity 16kA ,Fixed TM and 415 volts AC Supply ISI marked complete all as specified and directed by Engineer - in - Charge.

S & F in replacement MCB ‘C’ series type suitable for 240 volts, AC supply 32 Amps, S P & N with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S & F in replacement MCB ‘B’ series type suitable for 240 volts,10 KA, AC supply 6 to 32 Amps , single pole (SP) with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S &F storage type water heater (geyser) electrical operated 230/240 volts 25 ltr capacity, BEE 5 star rated complete with all safety equipment and accessories such as safety valve, thermostat, fusible plus etc required for proper functionality & including electric/earth connections and carrying out grouting & complete installations with mounting bolts , nuts including testing after installation complete all as specified and directed by Engr-in-Charge.

M & L for Earthing complete with GI earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 Mtr deep below ground level ) with top edge of plate not less than 1.5 Mtr below ground level , connecting to GI earth lead 4 mm dia GI earth wire ,by means of bolts,nuts and washers of GI and protection by provision of GI medium grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20 mm grade stone aggregate with 40 mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 gs /Sqmm ) and frame of angle iron 25mmX25mmX6mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape ,GI light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed ontop edge of earth plate common salt and charcoal filling test point made out of 40 mmX 8 mm FI with fixing arrangement ,funnel, wire mesh and earth work inhard dense soil ,returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs all as per electric plate no.3 of SSR part 1 and connecting to earth test point including taking out unserviceable earthing with all acessories all as specified or indicated including testing on completion all as specified and directed by Engr -In - Charge

M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth not less than 1.5 metre below ground level, earth plate surrounded by 15cm thick packed layer of charcoal dust and common salt, connected to galvanized iron strip 32mm x 6mm thick as earth lead by means of bolts, nuts and washers of galvanised iron or steel and thimbles and other end of the earth strip connected to earthing test point/equipment and protected by galvanised iron pipe light grade 40mm dia upto earthing test point/equipment fixed with 2 Nos of mild steel clamp made out 25mm x 3mm flat iron and perforated water pipe 20mm dia GI medium grade and top with socket & plug and bottom connected to earth plate by slit and two bolts/nuts/washers, PCC chamber in cement concrete (1:3:6) type C-1 and CI cover with frame all as shown in electrical plate No. 3 of MES Schedule Part-I of SSR-2009. Note:- (i) Outer edge of earth pit shall be 1 metre away from the outer edge of PCC chamber. (ii) GI strip upto earth test point/equipment is included in this item. (iii) Water pipe shall be provided in slantling position.

S&F heavy duty metal body exhaust fan of 300mm sweep , 240 volt , 5 star rating complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to disturbed wall in CM (1:4) white washing matching with existing color etc.

S&F heavy duty metal body exhaust fan of 250mm sweep , 240 volt , complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to disturbed wall in CM (1:4) white washing matching with existing color etc.

Taking down fan, ceiling cable and dismantling blades, painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified and directed.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and directed by Engineer - in - Charge.

M & L for Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. complete all as specified and directed by Engineer - in - Charge.

Hanging only ceiling fan (M.D. supply) and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed by Engineer - in - Charge.

Excavation in trenches not exceeding 1.5 mtr wide and not ecxceedinf 1.5 mtr depth for laying of cables complete all as specified and directed by Engineer - in - Charge.

Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25cm complete all as specified and directed by Engineer - in - Charge.

Removal of Excavated material n exceeding 50 mtr and depositing where directed complete all as specified and directed by Engineer - in - Charge.

Supply and filling in Sand for Cable protection complete all as specified and directed by Engineer - in - Charge.

Supplying and laying reinforced precast concrete cable cover, Class LV, Type I, flat, size 250 mm x 150mm x 40mm complete all as specified and directed by Engineer-in-Charge.

M & L for brick protection with old size sub class 'B' bricks laid flat , length of bricks across the route of underground cable complete all as specified and directed by Engineer-in-Charge.

Supply and lay jointing and testing and commissioning in replacement of 25 Sqmmx4 core XLPE insulated, screened , PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty multi stranded aluminium conductor & PVC sheathed LT cable 1100 V grade conforming to IS-7098 laid in trenches/ducts/fixed on poles wall/laid under roads/paths/drain/culverts or passing through pipes complete all as specified and directed by engineer in charge.

Supply and lay jointing and testing and commissioning in replacement of 35 Sqmmx4 core XLPE insulated, screened , PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty multi stranded aluminium conductor & PVC sheathed LT cable 1100 V grade conforming to IS-7098 laid in trenches/ducts/fixed on poles wall/laid under roads/paths/drain/culverts or passing through pipes complete all as specified and directed by engineer in charge.

Supply and lay GI pipe 50 mm light grade for cable protection in walls trenches or any situation including clamp nut bolt etc complete all as specified and directed by Engineer-in-Charge.

S & F Rigid non-metallic PVC conduit 20 mm dia inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. complete all as specified and directed by Engineer - in - Charge.

S&F TV socket having holes for 20mm conduit entry for tv connection all as specified and directed by Engr-in-Charge.

Akarsha Enterprises (BID ID -3344170)

AYUSH BUILDERS (BID ID -3336607)