SPECIAL REPAIR TO BLDG GULMARG MD ACCN AT DSSC WELLINGTON

Amount

Demolition of floor hearth or wall tiling including cement mortor bedding including cutting out brocken tiles complete all as specified and as directed.

Dismantling boarding, any description, fixed in any position with nailscomplete all as specified and directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frames) not exceeding 1.50 Sqm each complete all as specified and directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frames) exceeding 1.50 Sqm and not exceeding 4 Sqm each, complete all as specified and directed.

Demolition of cement concrete (unreinforced ) (below or above ground level) and removing debris off the site complete all as specified and as directed.

Demolition of Concrete of any description and in any position not otherwise specifically provided for drain,sunken floor etc all as directed by the Engr in charge.

Dismantling of single layer mangalore pattern roofing tiles all as directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings all as directed

Taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and as directed.

Demolition for brickwork or stone masonry laid with cement mortar or cement lime mortar

M&L Light shade coloured Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors and skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:4 complete all as specified and as directed. Make : Somany/Kajaria/Rak Ceramics

Dittoall as per item No11 above but set and jointed in neat cement slurry and pointed in coloured cement to match as in vertical surfaces of dado/skirting set in 10mm thick CM 1:3 complete all as specified

S&F second class hardwood plain,solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints, groove for fixing of glass etc complete all as specified and directed.

UPVC windows : Factory made UPVC of any colour as approved sliding Windows with glazing all as per manufacturer's direction and following specifications :- (i) UPVC Window frame shall be made of PVC material confirming to IS 10151, the Window frame shall be made of extruded UPVC section having overall dimension of 112 x 52 having wall thickness 2.5 mm ± 0.2 mm . (ii) Corners of wall frame shall be shall be joined by MS galvanized brackets. Joints shall be mitred and plastic welded. (iii) The hinge side of vertical outer frame shall be reinforced with galvanized MS tube of wall thickness 1 mm ± 0.1 mm and the tie rod shall be provided at the bottom of the frame. (iv) The profiles should be two or three chamber system which shall provide high insulation properties. (v) Glazing shall be provided with 5mm thick Plain / frosted glass fixed with appropriate size beading as per manufacurer's specifications. (vi) Stainless steel wire mesh 0.36mm nominal dia and average width of aperature 1.40mm shall be provided with each window shutter. Make : Madhu Industries / AMD overseas Ltd/ Gadli Industries/ Simta Astrix.

Note for item 14.00 : (I)The unit rate quoted by contractor includes cost of glass/wire netting and all other connected accessories. Net opening will be measured for payment purpose.

M& L for UPVC ventilator of any colour as approved with The profile for costruction of UPVC ventilator frame will be of overall size 60x58 mm with wall thickness 2.7 + or - 0.2 mm extruded sections. The corners will be plastic welded.The hinge side vertical outer frame shall be reinforced with galvanized channel of wall thickness 1.2 mm. The ventilator will be fixed to walls using 8 mm dia 80 mm dia MS screws minimium 2 nos on each sicde. The 3 nos of pinned glass will be placed in slots provided in ventilator. Glazing: The ventilator will be glazed with 5 mm thick pinhead glass. Note: The entire fixing will be done as per manufactures instructions and specification and as directed by Engg in charge. (II) The unit rate quoted by contractor includes cost of glass/wire netting and all other connected accessories. Net opening will be measured for payment purpose. Make : Madhu Industries / AMD overseas Ltd/ Gadli Industries/ Simta Astrix.

Supply and fix UPVC door shutters of any colour as approved with frames of approved make and colour with all necessary fixtures like hinges, handles, bolts etc all as specified and directed.Make : Madhu Industries / AMD overseas Ltd/ Gadli Industries/ Simta Astrix.

M&L for 2nd class hard wood (Sal / Hollock) factory made glazed and skeleton shutters 35 mm thick, open rebated and prepared to receive glass or gauge,etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing gauge sizes of members of shutters as specified in SSR Part-I Section-8, clause 8.24 (a) for door shutter supplying and fitted to chowkats, complete all as specified and directed. Make : CENTURY/GREEN LAM/JAIN

M&L for 35 mm thick flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides including 6 mm thick lipping patty around the shutter complete all as specified and directed. Make : CENTURY/GREEN LAM/JAIN

S&F Mild steel butt hinges 100mm long, medium weight, cold rolled.

S&F 150mm, extruded aluminium alloy handles, fabricated type, anodised complete.

S&F 150 mm long, Aluminum anodised barrel tower bolts, of extruded section complete as specified and as directed.

S&F 300mm long, Aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed complete as specified and as directed.

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Supply and fix in repairs 18mm thick High Density High Moisture Resistant (HDHMR) Board, both side laminated of approved colour as in shutters, back board, vertical support and horizontal shelves of kitchen/bedroom cupboards fixed with screw to timber framed work etc., including dismantling of existing any type of board and complete all as specified and as directed. Note: All exposed edges/surfaces to be finished with same laminated sheet to match with the other surfaces and nothing will be paid extra. Make : Kit Ply/Century/Greel ply/Action Tesa

M&L for Providing Gypsum board False ceiling using 12mm thick Gypsum board panels of size as approved by GE, fixed with staples on powder coated standard galvanized iron snap grid frame work of size suitable to fixing Gypsum board using 'T' and angle sections made out of 0.5mm thick PGI sheet, grade of zinc coating 220, bent to shape required as in main member, secondary member, perimeter angle section including provn of G I channel suspender fixed to roof members at the rate of 1200mm c/c and interspaced at 610mm c/c, the main fixing channel shall be fixed through fasteners clips as per manufacturer's instructions with and including plaster of Paris decorative type cornice all around at the junction of wall and ceiling including taking down and refixing of electrical fittings etc., complete all as specified and as directed. Note: The unit rate quoted shall be deemed to include the cost of taking down and refixing of the electrical fittings such as ceiling fan, light fittings etc., and keep in safe custody of same till refixing. The unit rate includes taking down of existing false ceiling completely.(ii) The unit rate includes taking down of existing false ceiling of any description completely.Make : Armstrong/Aerolite/Gyp Frame /Saint Gobain Gyproc/

M&L for Preparing of gypsum board false ceiling with primer and applying 3 mm thick wall care putty and applying two coats of OBD over one coat of primer complete all as manufacturer instructions and as directed Make : Asian/Berger/Nerolac

M&L for complete removal of existing finish on old gypsum board false ceiling including necessary preperation of surfaces and applying two coats of OBD over one coat of primer complete all as manufacturer's instructions and as directed. Make : Asian/Berger/Nerolac

M&L for non skid ceramic tiles7 to 8 mm thick (square/rectangular) area of each tile exc 0.06sqm but not exc 0.18 sqm, in floors and scantling etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:4 complete all as specified. Make : Somany/Kajaria/Rak Ceramics.

M&L for coloured glazed ceramic tiles of size 300mmx600mmx7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match as in vertical surfaces of dado/skirting set in 10mm thick CM 1:3 complete all as specified. Make : Somany/Kajaria/Rak Ceramics.

M&L for Sand filling using M-Sand under floors or in foundations including watering and consolidation complete all as specified and directed

M&L hardcore of gauge n.exc 63 mm deposited, spread & levelled in layers n. exc 15 cm thick, watered & rammed to a true surface with broken stone or boulders complete as specified and as directed.

M&L 75mm thick PCC 1:4:8 type D2 (40 mm graded aggregate) as in Sub base floor finished fair and even as in sub base of floor etc all as directed by the Engineer In Charge.

M&L Providing 25mm thick cement concrete type B0, 1:2:4 using 12.5 mm graded stone aggregate .as in floors for levelling course including finish the surface

S&F sheet glass ordinary quality 4mm thick in squares n. exc. 0.50 sqm in each pane and glazing with oil putty after hacking out old broken glass panes.

S&F sheet glass ordinary quality 4mm thick in squares n. exc. 0.50 sqm in each pane and glazing with oil putty complete all as spd and directed..

M&L 75mm thick Plain Cement Concrete type C-1, 1:3:6 (20mm graded stone aggregate) as in floors, plinth protection etc. finished fair and even without using extra cement complete as specified and as directed.

Material and labour for providing plain cement concrete 1:3:6 type C2, using( 40mm graded stone aggregate )as in drain / surface channel all as specified and as directed.

M&L for Precast cement concrete block Type C1(1:3:6)(using 20 mm graded stone aggregate) masonry with solid solid blocks exc 10cm width and setting in mortar(1:6) complete.

Material and labour for Rendering in Cement Mortar 1:6, 15mm thick on stone masonry or other than fair faces of brick work wall surfaces, finished even and smooth without using extra cement complete all as specified and as directed..

Material and labour for rendering 20mm thick in Cement Mortar 1:4 mixed with liquid water proofing compound as per manufacturers' instructions on stone masonry surfaces of wall, finished even and smooth without using extra cement complete all as specified and as directed. Note: Liquid water proofing compound shall be measured and paid separately.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,complete as in hard or dence soil all as directed.

Material and labour for providing plain cement concrete 1:3:6 type C2, using( 40mm graded stone aggregate )as in foundation filling and mass concrete all as specified and as directed.

M & L for mild steel work as in tubular roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat, square tube etc sections) including distance pieces, cleats etc. Fe 410-W (Gde-E- 250) quality- A complete all as specified and as directed. Make : TATA/JINDAL/SAIL

M/L preparing new surface of steel and appling two coats of synthetic enamel paint over a coat of primer red oxide Make : Asian/Berger/Nerolac

S & F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet crimped where ever required 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof coverings fixed with self tapping screws complete all as specified and as directed. Make: JSW/TATA/METCO ROOF PVT LTD

S & F for pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof coverings fixed with self tapping screws complete all as specified and as directed. Make: JSW/TATA/METCO ROOF PVT LTD

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove incl brushing neat cement slurry with 3.00kg of cement per sqm.

M&L for 75mm thick cement concrete type D2, 1:4:8 using 40mm graded aggregate as in subbase all as spd and dircected.

M&L for chequered cement concrete tiles of size 30cmx30cmx 25mm thick ,set ,jointed and pointed in neat cement slurry in floors with grey cement and pigments of required colour over 20mm thick thick screed bed in CM (1:6) complete as specified and as directed.

Taking down steel tubing and connections of 15 mm bore including cleaning for refixing or removal to store complete all as specified and as directed.

Taking down steel tubing and connections of 20 mm bore including cleaning for refixing or removal to store complete all as specified and as directed.

Taking down steel tubing and connections of 25 mm bore including cleaning for refixing or removal to store complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required & pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc; & cutting chases for concealed water tubing or concealed conduit wiring, etc.& making good, cutting not exc 10 cm grith in brick wall

S&F 15 mm bore Galvanised iron tubing, medium grade, with all fittings laid in trenches, floors or fixed to walls etc complete all as specified and as directed.Make: Jindal/Prakash/Tata

S&F 20 mm bore Galvanised iron tubing, medium grade, with all fittings laid in trenches, floors or fixed to walls etc complete all as specified and as directed.Make: Jindal/Prakash/Tata

S&F 25 mm bore Galvanised iron tubing, medium grade, with all fittings laid in trenches, floors or fixed to walls etc complete all as specified and as directed.Make: Jindal/Prakash/Tata

Refixing of old GI steel tubes and connections after cleaning of 15 mm bore in new or old position, any grade, to walls, ceiling, floors, etc complete all as specified and as directed.

Refixing of old GI steel tubes and connections after cleaning of 20 mm bore in new or old position, any grade, to walls, ceiling, floors, etc complete all as specified and as directed.

Refixing of old GI steel tubes and connections after cleaning of 25 mm bore in new or old position, any grade, to walls, ceiling, floors, etc complete all as specified and as directed.

S&F 25mm bore, Ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed,weight 455 gms complete as specified and as directed.

S&F 25mm bore, Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete as specified and as directed.

S&F 20mm bore, Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete as specified and as directed.

Supply and fix in repairs two way Bib cock 15 mm bore, cast copper alloy, chromium plated, fancy type with flange and crutch or butterfly handle conforming to IS as per Cat No.CON-041 of Jaquar or T3534A1 of Parryware or Cat No F730054 of Hindware, screwed down high pressure with fly nuts, screwed for iron pipes or for brass ferrule etc., complete all as specified and as directed.

S&F in repair health faucet Make:Cat No. E8342A1of Parryware /F160001 of Hindware/ ALD-CHR 565 of Jaquar including 1.2m long flexible tube and wall hook complete all as specified and as directed.

S&F in repair over head shower 200 mmx200mm including shower arm 20mm dia & 375 mm long round shape with 90 ° bend for wall mounted showers of with flange of Make: Cat No T9975A1,T-9802A1 of Parryware / F160142,F160024 of Hindware/ OHS-CHR-1619,SHA-479L450 of Jaquar or equivalent all as specified and directed .

S&F in repair toilet paper holder Make: Cat No T6906A1 of Parryware/ F890003 of Hindware/ CAN-1151N of Jaquar fixed to walls with chromium plated (CP) brass screws all as specified and directed .

Supply and fix in repairs stainless steel tubular towel rack 600mm long without lower hangers but with three hooks, Chromium plated as per Cat No.ACN-1181FHS of Jaquar or T6008A1 of Parryware or Cat No F580008 of Hindware fixed on walls complete all as specified and as directed .

Supply and fix in repairs corner glass shelf made out of glass with cp guard rail and wall fixing accessories of 300mm radius matt finished, chromium plated (MCH/Colour CP) with brass brackets as per Cat No.ACN-1173 of Jaquar or T6010A1 of Parryware or Cat No BEA-52 of PRAYAG fixed on walls complete all as specified and as directed .

Supply and fix in repairs Angular stop cock 15mm bore, cast copper alloy, chromium plated, fancy type with long shank conforming to IS as per Cat No.CON-053KN of Jaquar or G3053A1 of Parryware or Cat No F850030 of Hindware, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified and as directed.

S&F in repairs, two piece type stainless steel gratings square or round 100 mm size complete all as specified and as directed..

S&F in repairs 5.50mm thick looking mirror of size 900x600mm mounted on 6mm thick Plywood backing or AC sheet backing including framing with 1st class hard wood of size 40x40mm decorative type polished and fixed to wooden plugs with chromium plated brass screws and cupwashers/or chamferred glass from all sides fixed with steel screws all as specified and directed by Engr-in-Charge.

S&F sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete.Make: Bluestar/Parrware/Prayag

S & F in repair Single lever sink mixer with swinging spout, wall mounted model with connecting legs and wall flanges complete all as spd and directed Make- Cat No G3335A1 of Parryware/Cat No F320027 of Hindware/Cat No DRC-37165 of Jaquar or equivalent all as specified and directed.

Supply and fix in repairs, stainless steel plate racks made of stanless steel 0.80mm thick sheet standard size 24'x36x10" and design as approved by GE, complete all as specified and as directed. Make: Nirali/Parryware as approved by GE. Make : Parryware/Blustar/Prayag

S&F PVC connection 15 mm size with PTMT nuts of length 450 mm.

Taking down Cast iron / PVC pipe 75mm/ 110mm jointed in cement mortar taking out of wall. including all fittings, heads, sheos, bends, swan-necks, etccomplete all as specified and as directed.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/trenches complete all as specified and as directed.Make: Prince/Supreme/finolex

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.Make: Prince/Supreme/finolex

S & F PVC (SWR) bends any radious 110 mm bore provided with acess door.Make: Prince/Supreme/finolex

S & F PVC (SWR) bends any radious 75mm bore provided with acess door.Make: Prince/Supreme/finolex

S & F PVC (SWR)110mm bore branch piece single(single Y) equal or Unequal Make: Prince/Supreme/finolex

S & F PVC (SWR)75 mm bore branch piece single(single Y) equal or Unequal Make: Prince/Supreme/finolex

S & F PVC (SWR)110mm bore branch piece single(single T) equal or Unequal Make: Prince/Supreme/finolex

S & F PVC (SWR)75 mm bore branch piece single(single T) equal or Unequal Make: Prince/Supreme/finolex

S & F PVC (SWR) vent cowl 110 mm bore.Make: Prince/Supreme/finolex

S & F PVC (SWR) vent cowl 75 mm bore.Make: Prince/Supreme/finolex

Dismantling existing tanks exc. 250 lit & n. exc. 500 litres capacity, removing off the site complete all as specified and as directed.

Dismantling existing tanks exc. 500 lit & n. exc. 1000 litres capacity, removing off the site complete all as specified and as directed.

Supply and Fix, 1000 litres capacity triple layered Rotational Moulded Polyethylene (HDPE) FDA grade materials water storage tanks, (Cylindrical vertical with closed top) screwed lid type conforming to IS 12701-1996 with manhole lid and suitable locking arrangement including making holes for inlet, outlet, washout and over flow pipes, hoisted and fixed in position as specified in SSR Part -I (2009) complete all as specified and as directed. Make: Sintex/Polycon/Vectus

Supply and Fix, 500 litres capacity Rotational Moulded Polyethylene (HDPE) FDA grade materials water storage tanks, three layered (Cylindrical vertical with closed top) screwed lid type conforming to IS 12701-1996 with manhole lid and suitable locking arrangement including making holes for inlet, outlet, washout and over flow pipes, hoisted and fixed in position as specified in SSR Part -I (2009) etc., complete all as specified and as directed.Make: Sintex/Polycon/Vectus

Supply and fix in repairs stainless steel telescopic ball bearing channel, zinc plated finish for drawer including necessary fittings up to length of 600mm fixed with screws complete all as specified and directed.MAKE: EBCO/ GODREJ / KAFF / HETTICH

S & F stainless steel kitchen baskets (SS-304) of size 544mm x 505mm x 200mm complete all as specified and as directed.MAKE : EBCO, Cat No : RA-BCCS1-21-20-8 or equivalent in HETTICH/ KAFF/ GODREJ

S & F stainless steel kitchen baskets (SS-304) of size 544mm x 505mm x 100mm complete all as specified and as directed.MAKE : EBCO, Cat No : RA-BCCS1-21-20-4-CT or equivalent in HETTICH/ KAFF/ GODREJ

S & F stainless steel kitchen baskets (SS-304) of size 530mm x 505mm x 200mm complete all as specified and as directed.MAKE : EBCO, Cat No : RA-21-20-8 or equivalent in HETTICH/ KAFF/ GODREJ

S & F stainless steel kitchen baskets (SS-304) of size 530mm x 505mm x 150mm complete all as specified and as directed.MAKE : EBCO, Cat No : RA-21-20-6-PL or equivalent in HETTICH/ KAFF/ GODREJ

Supply and fix in repairs Stainless steel soft close hinge with 35mm cup dia, full overlay, 110 degree opening suitable for 18mm thick shutters complete all as specified and as directed.MAKE: EBCO/ GODREJ / KAFF / HETTICH

Supply and fix in repairs Gun metal handle of size 150mm for kitchen/bedroom cupboards fixed with screws complete all as specified and directed.MAKE: EBCO/ GODREJ / KAFF / HETTICH

Supply and fix in repairs Magnetic closer of suitable size for kitchen/bedroom cupboards fixed with screws complete all as specified and directed.MAKE: EBCO/ GODREJ / KAFF / HETTICH

Material and labour for Granite work with 18-20mm thick machine cut, Jet Black granite slab in single piece or two piece length, table rubbed and polished, laid over and including 20mm thick cement screed in cement mortar 1:3, bedded and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust and admixture of pigments to match with shade of granite stone as in cooking platforms, microwave platform, WHB counter top in steps, jambs, pillars, window-cills, etc, including cutting, polishing and rounding to edges of stone slabs etc., complete all as specified and as directed.

Mirror polishing on marble/ granite/Kota stone/ stone work as required to give high glossy finish complete all as specified and as directed

M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs, cooking platforms etc for even and smooth finish complete all as specified

M&L for RCC Type B1-1:2:4 (using 20mm graded aggregate )as in slab supproted on walls, beam and columns in floor, roof/cooking platforms etc

Supply only liquid water proofing compound of approved make complete all as specified and as directed.

Supply and fix in repair 50 mm bore Low density poly ethylene pipes (LDPE) of pressure rating 6 kg/sqcm in any length with rubber ring joint complete all as specified and as directed.

Demolition of Reinforced Cement Concrete of any description and in any position not otherwise specifically provided complete all as specified and as directed

S&F TMT Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete as specified and as directed.

M&L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work con- forming to Fe.290.Gde-E-165

M&L 0.63mm Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275.Make : TATA/ JSW/Metco

Labour only for fixing old seriviceable CGI sheet obtained from dismantling vide item No all as specified

M&L 0.80 mm Galvanised, plain mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) complete all as specified. Make : TATA/JSW/Metco

S&F 2nd class hard wood scantling as in rafters, purlins, trusses etc. clear sawn all as specified

M&L for second class hardwood clean sawn battern for MP/tiles exc 5Sqcm and not exc 15 sqcm in sectional area at 30 cm centres

M&L for roof tile, Mangalore pattern, interlocking at side joints, laid dry all as specified

Labour only for laying old roof tile, mangalore pattern, interlocking at side joints, laid dry all as specified

M&L in ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in cement mortar 1:6 all as specified

M&L for preparation of new mangalore pattern tile surfaces and appying two coats of tile guard over one coat of primer all as specified. Make : Asian/Berger/Nerolac

M&L for preparation of old mangalore pattern tile surfaces and appying one coat of tile guard all as specified. Make : Asian/Berger/Nerolac

Dismantling weather boarding of any description fixed in any position with nails.

M&L 2nd class Hard wood decorative Weather boarding, wrought, thickness 20mm to 25 mm and rebated on thick edge to give 20mm laps and fixed

Excavating in trenches, n.exc 1.5m wide and n exc 1.5 in depth; for foundation getting out hard/dense soil.

Returning filling including spreading leveling watering and well ramming in layers not exc 25 cm hard and dense soil

Material and labour for providing plain cement concrete 1:3:6 type C2, using( 40mm graded stone aggregate )as in foundation filling and mass concrete for manhole&Septic tank all as specified and as directed.

M&L for Walling of random rubble,uncoursed, well bonded, bedded and solidly hearted, built in cement mortar in CM(1:4) as in retaining wall etc complete.

M & L for PCC (1:3:6) type C-1 (using 20 mm graded stone aggregate) as in padding, coping, bed plates, hold fast blocks, etc., including formwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

M&L flush pointing to random rubble masonary uncoursed brought up to courses in CM 1:4 complete.

S&F in repairs double coat hook with brass brackets Make.Cat No 6905A1 of Parryware/ F580007 of Hindware / ACN -1161N of Jaquar or equivalent all as specified and directed by Engr-in-Charge

Complete removal of existing treatment on external walls by wire brushing, crack filling & Bio-wash to fight microbial growth and applying exterior wall putty of 3mm thick for smoothness, one coat of exterior wall primer and two coats of Exterior Emulsion anti fungal weather proof paint APEX ULTIMA OF Asian Paint or WEATHER COAT SMOOTH of Berger or Nerolac Excel Top Guard of Nerolac complete all as per manufacturer instruction as directed.Note:The painting work to be executed by authorised applicator of the manufacturer

M&L Preparing newly plastered surfaces/RMM surface of external walls and applying exterior wall putty of 3mm thick for smoothness, one coat of exterior wall primer and two coats of Exterior Emulsion anti fungal weather proof paint complete all as per manufacturer instruction as directed.Make:APEX ULTIMA OF Asian Paint / WEATHER COAT SMOOTH of Berger or Nerolac Excel Top Guard of Nerolac.

M&L for complete removal of existing treatment on surfaces of wall and applying with white putty of average thickness 3mm and making the surface to an even and smooth finish by rubbing with sand paper of different grade etc and applying two coats of Oil bound distermper over a coat of primer by approved applicator of the manufacturer of the paint and all as specified and as approved Make : Asian/Berger/Nerolac

M&L for preparation of new surfaces of walls and applying with white putty of average thickness 3mm and making the surface to an even and smooth finish by rubbing with sand paper of different grade etc and applying two coats of Oil bound distermper over a coat of primer by approved applicator of the manufacturer of the paint and all as specified and as approved. Make : Asian/Berger/Nerolac

M&L for preparation of old or previously treated wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats paint over one coat of pink primer complete all as specified and directed. Make : Asian/Berger/Nerolac

M&L for complete removal of existing treatment on surfaces of wall and ceiling surface of new or old and applying three coats of white wash complete all as specified and as directed. Make : Asian/Berger/Nerolac

Material and labour for Aluminium designer powder coated decorative curtain rods (Drapery rods) 20mm dia, exterior grade 3mm thick with and including side caps, holding clamps and 'F' and 'L' brackets, fixed to wall with PVC rawl plug and brass screws etc., complete all as specified and as directed.

Taking down old, unsv aluminium/copper point wiring (light, fan, socket or power) complete, incl fixture & fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit & making good the disturbed surfaces of walls, floors, etc. complete all as specified and directed by Engr-in-Charge. Note:Old existing Surface Mounting 4 ft/2ft ftg/ Wall mounting/down light/ Bulk Head/Bldg Security light fittings of any type taken down/dismantled to be deposited to MES E/M Storeyard and cost of transportation of the same from site of work to MES E/M Storeyard is deemed to be included in the unit quoted rates.

Taking down old sub-main wiring incl fixture & fittings etc. removing materials to store for keeping in safe custody or for taking credit & making good the disturbed surfaces of walls, floors, etc. complete all as specified and directed by Engr-in-Charge.

Disconnecting/dismantling of old existing un serviceable DB's any type/way 240/415 Volts with their old/un serviceable burnt MCCB/MCB's etc. complete all as specified and directed by Engr-in-Charge. Note-Old Exiting L&T DB incl MCBs to be submitted to MES Store yard ,Rate Quoted by the Contractor is deemed to be included the tranportation and Submitting DB

NOTE for Item Nos 134 to 136 : Cost of making good the disturbed surfaces is deemed to be included in the unit quote rates.

M & L for concealed point wiring with two single core 1.5 sqmm PVC insulated, unsheathed, FRLS cable, 1100 volts grade, ISI marked with multi stranded copper conductor drawn through and including non-metallic PVC rigid conduit (medium grade) with all fittings and accessories ISI marked incl provision of 1.5 sqmm PVC insulated, multistranded, unsheathed, copper conductor cable, FRLS, ISI marked as earth continuity conductor (green in colour) & incl fixing of modular metal flush boxes of appropriate size & thickness fixed flush to wall for mounting switch, sockets etc. with including cutting chases for conduits & sinkings for modular boxes & making good the disturbed surfaces, matching to the existing one etc. complete all as specified & as directed for the following : Make of cable : Havells/Polycab/Finolex.Make of conduit-Precision/Bajaj plast/finolex (a) One Light/fan/Call Bell etc. point controlled by one switch 5/6 Amps.

(b) Description all as per Item No-137 above but One switch socket outlet point 5/6 Amps on independent board.

Description all as per Item No-137 above but with FRLS PVC insulated copper conductor cable of size 2.5 Sqmm and 2.5 Sqmm for earth continuity conductor green in colour for 16A switch socket complete.

NOTE for Item Nos 137 to 139 1) Modular metal flush boxes shall be measured & paid separately. 2) Cutting chases & making good the disturbed surfaces is deemed to be included in the unit quoted rates.

M & L for concealed sub-main wiring alongwith earth wire of size (4x 6.00) sq. mm + (1 x 6.00) sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including non-metallic PVC conduit (medium grade) with all fittings and accessories ISI marked for conduits & sinkings for modular boxes & making good to walls, floors etc. complete all as specified & as directed. Make of cable : Havells/Polycab/Finolex, Make of conduit-Precision/Bajaj plast/finolex..

M & L for concealed sub-main wiring alongwith earth wire of size (2 x 6.00) sq. mm + (1 x 6.00) sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including non-metallic PVC conduit (medium grade) with all fittings and accessories ISI marked for conduits & sinkings for modular boxes & making good to walls, floors etc. complete all as specified & as directed. Make of cable : Havells/Polycab/Finolex, Make of conduit-Precision/Bajaj plast/finolex..

M & L for concealed sub-main wiring alongwith earth wire of size (2 x 4.00) sq. mm + (1 x 4.00) sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including non-metallic PVC conduit (medium grade) with all fittings and accessories ISI marked for conduits & sinkings for modular boxes & making good to walls, floors etc. complete all as specified & as directed. Make of cable : Havells/Polycab/Finolex, Make of conduit-Precision/Bajaj plast/finolex.NOTE for item No 6 to 8 : 1) Two/Four runs of PVC wire, one run of earth wire & one run of PVC rigid conduit (medium grade) will be measured as one length. 2) Modular metal flush boxes (if req) shall be measured & paid separately.2) Cutting chases & making good, including necessary Putty work of the disturbed surfaces is deemed to be included in the unit quoted rates.

S & F Modular switch, one way, 6 Amp, 1 Module, 240 volt complete all as specified and as directed. Cat No : ACVSXXW061, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor Roma

S & F Modular Bell Push switch, one way, 6 Amp, 1 Module, 240 volt complete all as specified and as directed. Cat No : ACVSBXW061, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor Roma

S & F Modular switch, one way, 16 Amps with indicator, 1 Module, 240 volt complete all as specified and as directed. Cat No : ACVSXIW161, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor Roma

S & F Modular shuttered socket outlet 3 Pin, 6 Amp, 2 Module, 240 volts, ISI marked complete all as specified and as directed. Cat No : ACVKSWW063, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor Roma

S & F Modular shuttered socket outlet 3 Pin, 6/16 Amp, 2 Module, 240 volts, ISI marked complete all as specified and as directed. Cat No : ACVKCWW163, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor Roma

Supply & Fixing and concealing modular metal flush box suitable for fixing switches/sockets of 1/2 modules all as directed. Cat No : ACTXMIIX01/02, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor Roma

Supply & Fixing and concealing modular metal flush box suitable for fixing switches/sockets of 3 modules all as directed. Cat No : ACTXMIIX03, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor Roma

Supply & Fixing and concealing modular metal flush box suitable for fixing switches/sockets of 4 modules all as directed. Cat No : ACTXMIIX04, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor Roma

Supply & Fixing modular cover plate suitable for fixing switches/sockets of 1/2 modules all as directed. Cat No : ACVPPCWV01/02, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor Roma

Supply & Fixing modular cover plate suitable for fixing switches/sockets of 3 modules all as directed. Cat No : ACVPPCWV03, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor

Supply & Fixing modular cover plate suitable for fixing switches/sockets of 4 modules all as directed. Cat No : ACVPPCWV04, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor

S & F TV coaxial socket,1 module complete all as specified and as directed. Cat No.-ACVKTOW001 Make : Legcus of Legrand or Verona of Crabtree(Havells) or Livia of Schneider

S & F internet socket RJ-45, suitable for CAT 6 cable, shielded, folded metal 1 module complete all as specified and as directed. Cat. No. ACVKJWW451 Make : Legcus of Legrand or Verona of Crabtree(Havells) or Livia of Schneider

NOTE for Item Nos 143 to 155 : The make/model of modular metal flush boxes & modular cover plates shall be same as that of modular switches & sockets.

Supply and fix Coaxial TV cable, RG-6 with less signal losses all as per Cat No.WHOJTTKARG06 of Havells fixed with necessary accessories complete all as specified and as directed

S&F ceiling rose surface PVC/ Polycarbonate, Isolated body with face Bakelite three terminal complete all as specified and directed. Make: Havells/CG/Anchor

S&F in repairs call Bell, AC, Buzzer Ding Dong type 230 Volt.Make: Anchor, Code-8432 or techno-commercially equiv in Legrand/Havells

S&F Surface and wall mounted LED batten 10 watts 2 feet long, extruded aluminium housing provided for efficient heat dissipation & integrated electronic driver including connecting up with and including twin/three core twisted flexible cable of suitable size in flexible conduit all as specified and as directed incl taking down old/unsv fittings. Make : Havells, CatNo:ENDURALINEARNEOBS10WLED865SPCSS or techno-commercially equiv In Jaguar/ Philips/ Luker

S&F Surface and wall mounted LED batten 20 watts 4 feet long, extruded aluminium housing provided for efficient heat dissipation & integrated electronic driver including connecting up with and including twin/three core twisted flexible cable of suitable size in flexible conduit all as specified and as directed incl taking down old/unsv fittings. Make :Havells, Cat No:ENDURALINEARNEOBS20WLED865SPCSS or techno-commercially equiv In Jaguar/ Philips/ Luker

S&F wall mount bed side decorative warm white fixture of 3W SS finish with opal glass diffuser complete all as specified and directed. Make : Luker, Cat No LWL 127-1 or techno-commercially equiv in Jaguar/Philips/ Havells.

S&F ultra modern, Surface mounted, 18W, 6500K LED Elegant surface panel complete with electronic driver & high brightness LED of Make: Luker cat No: LNPSRR18 or techno-commercially equiv in Philips/Havells all as directed by the Engr- in- charge.

S&F decorative wall mounting fixture luminaire with PC diffuser suitable for lamps with B22 with all accessories internally prewired and including necessary wiring/cabeling alterations of auto make the fitment completely capable for use as Engagement light & connecting up complete all as specified and as directed. Make: Havells, Cat No:LHFOAJE1TZ1I060, Model - Florentine or techno-commercially equivalent in Philips/Jaguar

Supply and fixing in repairs LED lamps 9W, 3000K with B-22 base cap all as directed by the Engr-in-Charge Cat No: LHLDDEBIA5R009 of Make Havells or techno-commercially equiv In Jaguar/Philips

Supply and fix Environment friendly, energy saving, surface mounted, decorative bulk head edge lit LED luminaire 10W or min 800 lumens with IP 66 with suitable fixing arrangement complete with all accessories internally prewired and including connecting up with and including twin core twisted flexible copper conductor cable of suitable size in flexible conduit all as specified and as directed. Make:Havells, Cat no HEXAFT10WLED857SSYMBOPC or techno-commercially equiv In Jaguar/Philips

Supply and fix energy saving high power LED building security light of 30W made up of pressure die cast aluminum housing with embedded PC cover having TOP Opening seperate driver compartment with IP66 protection including 40mm dia bracket bended into 120 degree angle and making connections in flexible conduit all as directed. Make: Cat no ENDURASUNDOWNSL30WLED757PASYBOPC Endura Sun Down of Havells or techno-commercially equiv In Jaguar/Philips

Imp Note for Item Nos 160 to 167 : 1) Design/Drawing/Technical catalogue/specifications along with comparative Rate Analysis to be submitted to the Engr-In-Charge/GE for Make/Sample approval of items whereever equivalency of Item(s) is concerned other than specified Make/Model/Cat/Part Ref concerned before placing order to the Manufacturer/Supplier. 2) Anything missed out in the technical specifications but technically required for efficient working is deemed to be included in the quoted rates.

S&F single pole and neutral enclosure with a two pin and earth plug and socket complete suitable for fixing one single pole MCB 20A C Series with Breaking capacity 10KA all as directed.Make: L&T, Cat No : DBMPS120SD or techno-commercially equiv in Legrand/ABB

Supply, Installing and Testing Vertical type Storage electric water heater (Geysers) of 25 Ltrs capacity, Tank made of ultra thick super cold rolled steel plates with high density PUF insulation,2 KW, 230 V, Single Phase, 50 Hz, AC, BEE 4 Star rated including multifuntion safety valve and 2 Nos anchor fasteners of size as per manufacturer instructions grouting and fixing and making good the disturbed surface complete and connecting electrical and water supply connection using steel braided hose 2 Nos complete all as specified and directed by the Engr-in-Charge. Make: Havells Model: Monza-DX,Cat No: GHWAMGSWH025 or techno-commercially equivalent in Racold/ Bajaj Note : (i)Installed Geyser's warrenty card duly signed by the user should be submitted to the Engr-in-Charge (ii) The cost of making good the disturbed surface & fixing arrangements required is deemed to be included in the quoted rate.(iii)Old unserviceable gyser to be submitted in MES Store yard (ii) The cost of transportation & Submitting old unsv geyser to MES storeyard is deemed to be included in unit quoted rates.

Supply, install, testing & commissioning of Exhaust fan, PVC body with connected accessories 250 mm sweep, single phase, 240 Volts, AC, 50 Hz,800RPM, Air delivery not less than 860 CMH, noise level less than 45 dB and connecting up complete including louvers and provision of cable 3/2 core of suitable size from ceiling rose to fan in flexible hose and making of suitable sized hole in the wall/existing window/ventillator etc. for fixing of the exhaust fan & making good the disturbed surfaces (if any) complete all as specified & as directed. Make : Havells, Cat No: Ventil Air DX or techno-commercially equivalent in Usha/Crompton. Note :- (i) The cost of making hole in walls/other surfaces & making good the disturbed surfaces incl any framework/cement work/wood work/welding work etc. required for proper fixing of the exhaust fan & matching to the existing surface is deemed to be included in the unit quoted rates.(ii) The cost of transportation & Submitting old unsv Exfan to MES storeyard is deemed to be included in unit quoted rates.

Supply, install, commissioning & testing of Exhaust fan, metal body with automatic back shutter louvers 300 mm sweep, 1400 RPM or more, Air Delivery not less than 1850 CMH, single phase, 240 Volts, AC, 50 Hz and connecting up complete including louvers and provision of cable 3/2 core of suitable size from ceiling rose to fan in flexible hose and making of suitable sized hole in the wall/existing window/ventillator/other surfaces etc. for fixing of the exhaust fan & making good the disturbed surfaces (if any) complete all as specified & as directed. Make : Havells, Cat No: Ventil Air - DB or techno-commercially equivalent in Usha/Crompton. Note :- (i) The cost of making hole in walls/other surfaces & making good the disturbed surfaces incl any framework/cement work/wood work/welding work etc. required for proper fixing of the exhaust fan & matching to the existing surface is deemed to be included in the unit quoted rates.(ii) The cost of transportation & Submitting old unsv Exfan to MES storeyard is deemed to be included in unit quoted rates.

S & F SPN DB, 12 Way, IP43, IK09, Metal double door type 240 volts fitted with busbar and blanking plates, neutral link and making good making good the disturbed surfaces with all other accessories including necessary connection all as specified and directed by Engr-in-Charge.Make: L&T, Cat No: DBSPN012DD or techno-commercially equiv in Legrand/Siemens

S & F SPN DB, 8 Way, IP43, IK09, Metal double door type 240 volts fitted with busbar and blanking plates, neutral link and making good making good the disturbed surfaces with all other accessories including necessary connection all as specified and directed by Engr-in-Charge.Make: L&T, Cat No: DBSPN008DD or techno-commercially equiv in Legrand/Siemens

S&F MCCB, 4 pole,63 A rating (Ics=100% of Icu),415Volts,36 KA Breaking capacity with adjustable overload & adjustable Short circuit setting complete all as specified & as directed by the Engr-in-Charge.Make: L&T, Cat No CM97919OOH2OG or techno-commercially equiv in Legrand/ABB/Siemens.

S&F 4 Way,IP43,IK-09 Metal Double Door,TP&N vertical DB fitted with Busbar and blanking plates, Neutral link with 4 pole MCCB as Incomer and SP/TP MCBs as outgoings,without MCCB, flushing to wall/fixing inside enclosure and making good the disturbed surfaces with all other accessories including necessary connection complete all as specified and directed by Engr-in-Charge.Make: L&T, Cat No: DBVTL004DD or techno-commercially equiv in Legrand/ABB/Siemens. Note:- (i) The cost of making good the disturbed surfaces is deemed to be included in the unit quoted rates.

S&F Miniature circuit Breakers, SPN,C-Series 240 Volts of capacity 6-32 Amps with breaking capacity 10 KA all as specified and dircted by Engr-in-Charge. Make-L&T, Cat No-AU10S20(06-32)3C or techno-commercially equivalent in Legrand/ABB/Siemens.

S&F Miniature circuit Breakers, SPN,C-Series 240 Volts of capacity 40 Amps with breaking capacity 10 KA all as specified and dircted by Engr-in-Charge. Make-L&T, Cat No-AU10S20403C or techno-commercially equivalent in Legrand/ABB/Siemens.

S&F Miniature circuit Breakers, SP,C-Series 240 Volts of capacity 40 Amps with breaking capacity 10 KA all as specified and dircted by Engr-in-Charge. Make-L&T, Cat No-AU10S10403C or techno-commercially equivalent in Legrand/ABB/Siemens.

S&F Miniature circuit Breakers, single pole,C-Series 240 Volts of capacity (6-32 Amps) as ordered with breaking capacity 10 KA. Make-L&T, Cat No-AU10S10(06-32)3C or techno-commercially equivalent in Legrand/ABB/Siemens.

S & F MCB, DB, TPN, 04ways, DOUBLE DOOR, IP-43, Ik-09 with metal door, rated bus bars, earth bar, neutral links complete including blanking plates as required and fixed flush to wall/other surface complete all as specified and as directed. Make : L & T, Cat No : DBTPN004DD or techno-commercially equivalent in Siemens/Legrand.

S & F MCB, TP, 10KA, 415V, "C" curve, 63 A, ISI marked complete all as specified and as directed. Make : L & T, Cat No : BB30630C or techno-commercially equivalent in Siemens/Legrand.

S & F MCB, TPN, 10KA, 415V, "C" curve, 63 A, ISI marked complete all as specified and as directed. Make : L & T, Cat No : BB40630C or techno-commercially equivalent in Siemens/Legrand.

S & F in repairs Sheet metal enclosure for DBs when MCCBs to be used, 4 Pole, 415 Volt, Single Door with 100Amps rated bus bar and blanking plates of Make : L&T, Cat No CM90996OOOO or techno-commercially equiv in Legrand/ABB. Note:- (i) The cost of making good the disturbed surfaces is deemed to be included in the unit quoted rates.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2.25mtrs deep below ground level) with top edge of plate not less than 1.5mtrs below normal ground level, connected to GI strip of size 32X6 by means of bolts,nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 connected to earthing test point on completion with and including 40mm bore medium grade GI protection pipe (upto 7.5mtr long) for earth and 20mm GI medium grade for watering including PCC chamber pit & cover with suitable lifting hooks, with funnel, wire mesh, common salt, charcoal filling, necessary excavation and earth work in any type of soil complete all as specified including taking out the existing u/s earthing accessories. Note: On testing after completion, if the desired earth resistance is not obtained the earthing shall be redone at no extra cost till the entire satisfaction of Engr-in-Charge. . Make of GI Pipe : TATA/Jindal/Prakash

S & F FRP enclosure of size 1000(L) x 690(W) x 215(D) approx or next higher size with locking arrangement and making flush to the wall, fixing MCCB DB inside with suitable accessories and fixing the energy meters 04/06 Nos inside incl taking down the old enclosure complete all as specified and directed by Engr-in-Charge. Make: Sintex, Model No GSMB-10069 or techno-commercially equivalent in Hensel/Rittal/OBO. Note : (i)The cost of making good the disturbed surface and matching to the existing surface is deemed to be included in the unit quoted rates. (ii) The cost of making cut or hole to the enclosure as per site requirements is deemed to be included in the unit quoted rates.

SRIBALAJI AND CO