CA NO. GE AF NO.1/GUR-49/2025-26 REPAIR, MAINTENANCE AND REPLACEMENT OF INTERNAL ELECTRIC US POINT WIRING AND FITTINGS, EXHAUST FANS, SERVICING OVERHAULING OF CEILING FANS, SUBMAIN WIRING LED FITTINGS / FIXTURES, E/M WORKS AT 54 ASP GURGAON

Amount

Schedule-A (E/M Work)

Taking down and serviceing of ceiling fan 1200/1400 mm sweep at site and removing of old grease from bearing of ceiling fan and re-filling new grease including replacement of worn out nut bolt, rubber real bush gun metal ball bearing capacitor split and reassembling the fan complete including testing after assembling and connecting to electric system complete all as specified and as directed by Engr-in-Charge. NOTE:- Rates of bearing, capacitor, blades & painting will be paid seperately in the concered item of schedule.

All as per srl item No 1 above but for wall mounting fan plastic type of size 400/450mm sweep complete.

All as per srl item No 1 above but for exhaust fan of any size complete.

Taking down carefully AC single phase 220/230volt wall mounting fan 450mm sweep single phase complete at site for rewinding and replacement of unserviceable parts i.e Capacitor, PVC connector, MS galvanised check nut, ball bearing, rubber pads, PVC strip clamps including servicing such as removing dust & dirt brushing, rubbing with cotton waste, , washing with detergent powder to fan blades, greasing bearing with ball bearing grease & washer packing, checking of bolts/nuts, washer check nuts split pin rubber packing and rubber seal etc including testing after assembling and connecting to electric system complete all as specified and as directed by Engr-in-Charge. Note : 1. Rates of winding and replacement of any unserviceable parts mentioned above required to make the fan in serviceable condition are include in the quoted rate. 2. Old winding of the fans will be destroyed/damaged by the department before handing over the fan to contractor for repair. 3. After repair contractor will be fully responsible for checking of copper winding and thereafter the same will be assembed, re-hanging and electric connection complete. 4. Rates of bearing, bush, capacitor, blades & painting will be paid seperately in the concered item of schedule.

All as per srl item No 4 above but for wall mounting fan plastic type of size 450mm sweep complete.

All as per srl item No 4 above but for exhaust fan of size 250mm sweep plastic type square/round shape complete

All as per srl item No 4 above but for exhaust fan300mm sweep complete.

All as per srl item No 4 above but for exhaust fan 450mm sweep complete.

All as per srl item No 4 above but for exhaust fan 600mm sweep complete.

All as per srl item No 4 above but for air circulator wall mounting fan metallic type 450mm sweep complete.

All as per srl item No 4 above but for air circulator wall mounting fan metallic type 600mm sweep complete

S&F in replacement capacitor 2.5 mfd + 5%, 220/230 volts AC, 50 c/s

S&F in replacement capacitor 3.15 mfd + 5%, 220/230 volts AC, 50 c/s

S&F in replacement capacitor 4 mfd + 5%, 400/440 volts AC, 50 c/s

S&F Electric cable PVC insulated with copper conductor (flexible cable) size 23/0.0076 twin core for connecting fan to electric system, complete all as specified & directed.

Taking down and Spray painting to AC ceiling fan 1200/1400mm sweep any make complete to motor assy, down rods, blades with ISI marked white/brown synthetic enamel paint as approved by Engr-in-Charge after preparation of surface including filling cavities with filler, writing of MES No complete and refixing the same in existing location after painting complete all as specified and as directed by Engr-in-charge

Taking down metallic type wall mounting fan of size 400/450mm sweep in situ for spray painting with ISI marked OG/brown/black synthetic enamel paint as directed by Engr-in-charge after preparation of surface and refixing the same in existing location after painting complete all as specified and as directed by Engr-in-charge

All as per item No 19 but for exhaust fan 300mm.

All as per item No 19 but for exhaust fan exceeding 300mm and upto 450mm.

All as per item No 19 but for exhaust fan exceeding 450mm and upto 600mm.

All as per item No 19 but for air circulator wall mounting fan of size 450 to 600mm .

S&F Canopies for AC ceiling fan of size 1200/1400mm sweep for any make of fancomplete all as specified and as directed by Engr-in-charge.

S&F down rods for ceiling fan 1200/1400mm sweep of size 2.5' long duly painted with white synthetic enamel paint complete all as directed by Engr-in-charge

S & F Hanging clamp suitable for ceiling fan of size 1200/1400mm of any make complete with nuts, bolts, rubber reel and locking pin complete all as directed by Engr-in-Charge.

S&F step type elctronic fan regulator in replacement Modular type, single phase 220 V, All as specified and directed by Engr-in-Charge.

S&F step type elctronic fan regulator in replacement Flush type, single phase 220 V, All as specified and directed by Engr-in-Charge.

S&F louvers for exhaust fan of size 300mm sweep made out of MS sheet 22 gauge complete all as specified and as directed

S&F louvers for exhaust fan of size 450mm sweep made out of MS sheet 22 gauge complete all as specified and as directed

M&L in replacement fan blade (set of 03) suitable for 1200 mm sweep all as specified and as directed by Engr-in-Charge.

M&L in replacement fan blade (set of 03) suitable for 1400 mm sweep all as specified and as directed by Engr-in-Charge.

S&F in replacement wall mounted fans blades (set of 03) suitable for 400/450 mm sweep any make and suitable colour all as specified.

S&F in replacement exhaust fans blades suitable for 300/450 mm sweep any make and suitable colour including taking down all as specified.

Supply and fix Ball bearing suitable size of Exhaust fan any type and size.

Supply and fix Ball bearing suitable size of wall maunted fan any type and size.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, (fittings such as switches, ceiling roses, pendants, regulators, sockets etc. to be measured separately), removing materials to store for keeping in safe custody for re-use at site/Sch of credit and making good disturbed surface of walls, floors, etc., complete all as specified and as directed by Engineer-in-Charge.

M&L for point wiring complete with 1.5 Sqmm (nominal area) PVC insulated, multi stranded, FRLS copper conductor cable unsheathed in and including PVC conduit with all fittings medium grade ISI Marked and PVC insulated FRLS copper conductor cable of size 1.5 sq mm as earth wire, connected to common earth dolly suitable for mounting modular switches including modular metal flush boxes and modular face plate complete all as specified and as directed by Engr-in-charge,(The works includes cutting of chasis and making good disturbed surfaces alongwith finishing the suface with matching the existing paint coat all this work should included in the rate deemed to included in quated rate):-

One light point controlled by one way one switch SP 5 Amps , 240 V.

One ceiling fan / Exhaust point controlled by one way one switch SP 5 Amps, 240 V.

One light point controlled by two 2 way switch SP 5 Amps ,240 V.

One switch socket outlet 3 Pin, 5 Amps, SP on independent board.

One switch socket outlet 3 Pin, 5 Amps, SP on same board.

One bell point controlled by one way one switch SP 5 Amps , 240 V.

All as per the item No 36 here in before but with 2.5 Sqmm cable for 3 pin 15 Amps socket complete all as specified and as directed by Engineer-in-Charge.

S&F modular socket outlet 6A, 2/3 pin combined 2 module, complete all as specified and as directed by Engineer-in-Charge.

S&F modular socket outlet 6A/16A, 2/3 pin combined 2 module, complete all as specified and as directed by Engineer-in-Charge.

S&F modular switch 1 way 6 Amps 1 module, complete all as specified and as directed by Engineer-in-Charge.

S&F modular switch 2 way 6 Amps 1 module complete all as specified and as directed by Engineer-in-Charge.

S&F modular switch 1 way 16 Amps 1 module, complete all as specified and as directed by Engineer-in-Charge.

S&F ceiling rose 3 phase/PVC/ polycarbonate isolated body, complete all as specified and as directed by Engineer-in-Charge.

S&F modular bell push switch 1 way 6 Amps 1 module, complete all as specified and as directed by Engineer-in-Charge.

S&F switch piano flush type single pole one way , 5 Amps , 240V grade ISI marked , complete all as specified and as directed by Engineer-in-Charge.

S&F switch piano flush type single pole one way , 15 Amps , 240V grade ISI marked, complete all as specified and as directed by Engineer-in-Charge.

S&F socket outlet 2 in 1 ,3 pin 5 Amps flush type ISI marked, complete all as specified and as directed by Engineer-in-Charge.

S&F socket outlet 2 in 1 ,3 pin 5 and15 Amps flush type ISI marked, complete all as specified and as directed by Engineer-in-Charge.

S&F switch bell push piano flush type single pole one way , 5 Amps , 240V grade ISI marked, complete all as specified and as directed by Engineer-in-Charge.

S&F switch piano flush type single pole two way , 5 Amps , 240V grade ISI marked, complete all as specified and as directed by Engineer-in-Charge.

Taking out old U/S submain wiring of any size and removing from site including making good of existing surfaces complete all as specified and as directed.

M&L sub main wiring with multistranded FR copper conductor cable PVC sheathed in and including concealed suitable size PVC conduit medium grade with fittings and two runs of 6 Sqmm and one run of 4 Sqmm FR copper conductor as earth wire and connected to earth dolly all as specified and as directed by Engr-in-Charge (The works includes cutting of chasis and making good disturbed surfaces alongwith finishing the suface with matching the existing paint coat all this work should included in the rate deemed to included in quated rate).

M&L sub main wiring with multistranded FR copper conductor cable PVC sheathed in and including concealed suitable size PVC conduit medium grade with fittings and two runs of 10 Sqmm and one run of 6 Sqmm FR copper conductor as earth wire and connected to earth dolly all as specified and as directed by Engr-in-Charge. (The works includes cutting of chasis and making good disturbed surfaces alongwith finishing the suface with matching the existing paint coat all this work should included in the rate deemed to included in quated rate).

S&F in replacement of Gong Bell, single phase 12Inch, 230 volt AC, 50 HZ, complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement of Ding Dong Bell, single phase, 230 volt AC, 50 HZ, complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement , Batten holder bakelite AC, 220 V, complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement of sheet metal 2 way DB Box complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement of sheet metal enclosure single pole and neutral 4 way Double door 200 Amps rated bus bar complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement of sheet metal enclosure single pole and neutral 12 way Single door 200 Amps rated bus bar complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement of metal enclosure for MCB's (D.B) 8 way (SPN) 200 Amps rated bus bar complete all as specified and as directed.

S&F in replacement of sheet metal enclosure triple pole and neutral 415 Volts 4 way 200 amp rated double door when MCCB is used, complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs sheet metal enclosure triple pole and neutral vertical Loadline 415 Volts 6 way (TPN) double door when MCCB is used.

S&F MCB 240 volts SPN 06- 32 amp 10KA breaking, capacity, ISI marked, complete all as specified and directed.

S&F MCB 240 volts 2 pole (DP) - 40 amp 10KA breaking, capacity, ISI marked, complete all as specified and directed.

S&F MCB 240 volts 2 pole (DP) - 63 amp 10KA breaking, capacity, ISI marked, complete all as specified and directed.

S&F MCB 240 volts SP 6- 32 amp 10KA breaking, capacity, ISI marked, complete all as specified and directed.

S&F MCB 415volts TPN 40 amp 10KA breaking, capacity, ISI marked, complete all as specified and directed.

S&F MCB 415volts TPN 63 amp 10KA breaking, capacity, ISI marked, complete all as specified and directed.

Supply & Fix in replacement of MCCB 63 Amps, 4 pole 415 V conform to IS/IE60947-2 with breaking capacity 16 KA Adjustable Thermal and Fixed Magnetic complete.

S&Fof MCCB 100 Amps 4 pole 415 Volts conform to IS/IE60947-2 with breaking capacity 16 KA Adjustable Thermal and Fixed Magnetic complete all as specified and directed.

S&F Blanking plates suitable for MCB DB's complete all as specified and directed

Supply and fixing industrial panel mounting Socket Splash proof 16 amp protection degree 44.

Supply and fixing industrial panel mounting Plug Splash proof 16 amp protection degree 44.

S&F in replacement Recess mounted 2X2 high effciency LED luminaires 36 Watt, CCT not less than 6500K, efficacy not less than 120lm/W with inbuilt 4PIR occupancy sensor provided in luminaire for switching as per the movement of person. LED luminaire made in CRCA sheet metal with wider light window and opal polystyrene diffuser for spotless glare-free uniform lighting for offices and modern workspace areas complete all as directed by Engr-in-charge.

S & F in replacement 1X1 recess mounted high effciency luminaires of 18W, CCT not less than 6500K, efficacy not less than 110lm/W made in CRCA E106 sheet metal with wider light window and opal polystyrene diffuser for spotless glare-free uniform lighting for offices and modern workspace areas all as specified and directed

S & F in replacement LED surfase light square 22 watt of size 205mm x 205mm, CCT not less than 4000k and efficacy not less than 100 lm/W with cover.

Supply and fixing in replacement Designed with high quality aluminium extrusion these LED battens of 20Watt, CCT not less than 6500K and efficacy not less than 100lm/W have sturdy housing for surface mounting applications and boasts of an improved LED life all as specified and directed .

Supply and fixing in replacementSelf ballasted Led Retrofit Bulbs with PBT Body shell and PC diffuser LED LAMP 7 Watt, Colour Temp not less than 6500 K

Supply and fixing in replacement of indoor decorative LED batten light fitting 1x9/10W, not less than 6500K lumen tube light fitting with 2 feet long LED Tube of 9/10W complete with all accessories internally prewired complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement Self ballasted Led Retrofit Bulbs with PBT Body shell and PC diffuser LED LAMP 14 Watt , CCT not less than 6500 K

S&F in replacement of Gang box for 15 Amps socket complete including 15 Amps switch socket combination complete.

S&F in replacement of Gang box for 5 Amps socket complete including 5 Amps switch socket combination complete.

M&L for checking of Energy Meters single/three phase 2/4 wire of any Make /type including testing , checking and reporting any tempering and intimate meter reading at time of electric meter testing & re-sealing all as specified and directed. (NOTE: Necessary transportation upto building testing and checking arrangements with equipment and metre calibration certificate will be provided by contactor)

M&L for taking down unserviceable energy meter 1 phase from meter box after disconnecting all incoming and outgoing connection and deposite to MES store complete all as specified and as directed by Engr-in-charge

M&L for taking down unserviceable energy meter 3 phase from meter box after disconnecting all incoming and outgoing connection and deposite to MES store complete all as specified and as directed by Engr-in-charge

Supply and fix electronic meters temper proof LCD display with polycarbonate cover 230 V, 10- 60Amp, accuracy class-I 50Hz, conforming to IS 13779, IP-54, with parameters to show data, time, current reading, load, PF, voltage and KWH

As per Item No 86 Ditto but 3 Phase, 415 volt

S & F in repalacement service connection 1100 volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheathing of PVC tape and over all PVC sheathed of size 6 Sqmm, 2 core complete all as specified and directed by Engr-in-Charge.

S & F in repalacement service connection 1100 volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheathing of PVC tape and over all PVC sheathed of size 10 Sqmm, 2 core complete all as specified and directed by Engr-in-Charge.

S & F in replacement of Exhaust fan iron body type 300mm Sweep, speed 1425RPM, air delivery 750CMH, power 50W, colour metallic grey including making necessary civil work and well finished hole for fixing.

S & F in replacement of Exhaust fan PVC body type 300mm Sweep, Speed 1400RPM, Air Delivery 210 CMH, power 52W including making necessary civil work and well finished hole for fixing.

S & F in replacement of Wall mounted fan 400mm speed 1350 RPM , Air delivery 65 CMM, power 65 W, Rust proof body, 100% copper motor, BIS certified.

S& F wall mounting, brushed nickel finish fixture with Opal Glass diffuser suitable with 9 W LED all as specified and directed by Engr-in-charge

S&F Recess and surface/pendant mounting LED flat panel 1'x4' made of CRCA sheet steel with high efficient LEDs & glare free opal diffuser IP 20, CCT not less than 6500k and efficacy not less than 100 lm/W

S&F Exhaust fan Motor copper winding of 18inch size all as specified and direcfed by Engr-in-charge

S&F Exhaust fan Motor copper winding of 12inch size all as specified and direcfed by Engr-in-charge

S&F Exhaust fan Motor copper winding of 9inch size all as specified and direcfed by Engr-in-charge

S&F Projector LED projector lights with high lumens output of 8W, CCT not less than 4000k and efficacy less than 100lm/W all as specified and directed by Engr-in-charge.

S&F energy efficient wall mounted Bulkhead LED 10Watt, CCT not less than 5700K, efficacy not less than 95lm/W light plastic housing and enclosed with cover IP 65 all as specified and directed by Engr-in-charge.

M&L for GI Pipe light grade 40mm for protection of cable/strip etc fixed in wall/trenches etc all as specified and directed

S&F Energy saving and environmental friendly long life LED street light 35 Watt made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having IP65 protection and Impact resistance of IK07 with 10KV Built-in Surge Protection Device alongwith 30mm dia Medium Grade GI Pipe of 1mtr with bracket and stand for fixing in wall complete all as directed and specified by Engr-in-charge

S& F LT/CT digital energy meter current rating 350LT , Voltage 230/240V(P-N), accuracy: class 0.5 , Frequency : 50Hz, Temp : 25degree celcius to 70 degree celius all as specified and directed by Engr-in-charge.

M& L for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6 mm thick, buried directly in ground(earthpit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead with 4mm dia with protection pipe 15mm GI Light grade PIpe by means of bolts, nuts and check nuts and washers of GI or steel all as shown in Electrical plate No 3 including earth work funnel with watering arrangement, wire mesh, GI pipe 20mm internal dia light grade buried directly vertical and adjacent to the electrode for watering , PCC pit 1:3:6 type C1 and RCC chamber cover in 1:2:4 type B1 of size 550 x 550mm with 8 mm dia TMT bar of 100mm C/C both ways including of returning, filling in and removal of surplus soil to a distance not exc 50 m as specified and directed by Engr-in-charge including testing on completion. Note: The strip/wire upto 7.5mtr included in the quoted rate.

S&F Onload Changeover switchs of capacity 630Amps SS operated 415V , 50 Hz conforming IS/IEC 60947-1 & 3 complete all as specified and directed by Engineer-in-Charge.

S&F in replacement Onload Changeover switchs of capacity 200Amps SS operated 415V , 50 Hz conforming IS/IEC 60947-1 & 3 complete all as specified and directed by Engineer-in-Charge.

S&F in replacement Onload Changeover switchs of capacity 160 Amps SS operated 415V , 50 Hz conforming to IS/IEC 60947-1 & 3, complete all as specified and directed by Engineer-in-Charge.

S&F in replacement Onload Changeover switchs of capacity 100 Amps SS operated 415V , 50 Hz conforming to IS/IEC 60947-1 & 3, complete all as specified and directed by Engineer-in-Charge.

S & F in replacement LED Tube light surface and wall mounted LED batten of 20W, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver with industrial grade heavy duty driver having THD<10%.

S&F in replacement sheet metal enclosure for MCB's (D.B) 6 way (SPN)IK 08 provided with 200A insulated phase bus-bar ,neutral bar/s with shroud/s, earth bar/s, sticking saddles, cement spill protector, color-coded interconnecting wire set, cable ties,blanking plates and circuit identification label complete all as specified and as directed.

S&F in replacement sheet metal enclosure for MCB's (D.B) 4 way (TPN) IK 08 provided with 200A insulated phase bus-bar ,neutral bar/s with shroud/s, earth bar/s, sticking saddles, cement spill protector, color-coded interconnecting wire set, cable ties,blanking plates and circuit identification label complete all as specified and as directed.

S&F in replacement of MCB SPN 06- 32 amp ‘C’ Series (In accordance with IS/IEC 60898-1) 240 V/415 V, 50 Hz, 10kA, capacity complete all as specified and as directed.

S&F in replacement of MCB SP 06- 32 amp ‘C’ Series (In accordance with IS/IEC 60898-1) 240 V/415 V, 50 Hz, 10kA, capacity complete all as specified and as directed.

Dismantling and taking up old existing unserviceable GI/copper earth plate with strip earthing and connected items complete all as specified and as directed by Engr in charge.

M&L in replacement for earth continuity conductor or main earthing lead fixed to Floor/wall / roof/Air termination and connecting Machinery to test point with 25x3 mm Copper strip including taking down existing copper strip complete all as specified and directed

S&F in replaement of porcelin viterous white/ brown/ green insulators of sizes 25mm x 25mm having provision of two holes for fixing on roof / wall under strip/ channel on top for running of down conductors to maintain gap between wall and down conductors etc complete all as specified and directed by Engr-in-Charge.

M&L for earthing pit with brick work and PCC 1:3:6 including RCC pit cover of size 300x300mmx50mm thick with provision of opening handle complete including necessary watering, ramming and compact of soil near the earth pit all as specified and as directed by Engr-in-charge

M&L in replacement for earth continuity conductor or main earthing lead fixed to Floor/wall / roof/Air termination and connecting Machinery to test point with 25x3 mm aluminium strip including taking down existing aluminium/GI strip complete all as specified and directed by Engr-in-Charge .Note :- (i) Laying / fixing of strip from air termination to test point shall be in one run i.e. there shall be no joint in between air termination. In case joint is required, it shall be jointed with nut & bolt joint with breezing full contact of strip. ii) Strip shall be fixed on insulator at the interval not more than 900mm in such a manner at any place it shall not touch to wall/ roof / any metalic body. (Cost of insulator shall be measured and paid seprately under respective items of Sch of works as supply only)

S & F in repalacement service connection 1100 volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheathing of PVC tape and over all PVC sheathed of size 6 Sqmm, 2 core complete all as specified and directed by Engr-in-Charge. Make :-Plaza/Polycab/Havells

S&F in replacement of XLPE insulated heavey duty electric cables with aluminium conductor, 1100volts grade, cross-sectional area 16sqmm 4core all as specified and directed

S&F in replacement of XLPE insulated heavey duty electric cables with aluminium conductor, 1100volts grade, cross-sectional area 10sqmm 2core all as specified and directed

S&F in replacement of XLPE insulated heavey duty electric cables with aluminium conductor, 1100volts grade, cross-sectional area 25sqmm 4core all as specified and directed

S&F in replacement of XLPE insulated heavey duty electric cables with aluminium conductor, 1100volts grade, cross-sectional area 35Sqmm 3.5core all as specified and directed

S&F in replacement of XLPE insulated heavey duty electric cables with aluminium conductor, 1100volts grade, cross-sectional area 50Sqmm 3.5core all as specified and directed

S&F in replacement of XLPE insulated heavey duty electric cables with aluminium conductor, 1100volts grade, cross-sectional area 70Sqmm 3.5core all as specified and directed

S&F in replacement of XLPE insulated heavey duty electric cables with aluminium conductor, 1100volts grade, cross-sectional area 95Sqmm 3.5core all as specified and directed

S&F in replacement of XLPE insulated heavey duty electric cables with aluminium conductor, 1100volts grade, cross-sectional area 120Sqmm 3.5core all as specified and directed

S&F in replacement of XLPE insulated heavey duty electric cables with aluminium conductor, 1100volts grade, cross-sectional area 400Sqmm 3.5core all as specified and directed

Supply and fixing in replacement of galvanized iron tubing 100mm bore medium grade with all fittings with all its fittingsi.e union ,tee, elbow etc used for connection complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of galvanized iron tubing 80mm bore medium grade with all its fittingsi.e union ,tee, elbow etc used for connection complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of galvanized iron tubing 50mm bore medium grade with all its fittingsi.e union ,tee, elbow etc used for connection complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement galvanized iron tubing 40mm bore medium grade with all its fittingsi.e union ,tee, elbow etc used for connection complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement galvanized iron tubing 25mm bore medium grade with all its fittingsi.e union ,tee, elbow etc used for connection complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement galvanized iron tubing 20mm bore medium grade with all its fittingsi.e union ,tee, elbow etc used for connection complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement galvanized iron tubing 15mm bore medium grade with all its fittingsi.e union ,tee, elbow etc used for connection complete all as specified and directed by Engineer-in-Charge.

M&L complete for drilling hole through machine under hard standing /road in different location as per site requirement (between 03 mtr to 40mtr maximum) for laying of pipe for protection of cable etc by means of bookle and without disturbing the top surface and making good the disturbed surface if any complete all as specified.

Excavation in trenches not exceeding 1.5M wide and not exceeding 1.5M in depth for foundation etc or for shafts wells, cesspits, mahnoles, pier holes ect not exc 10 Sqm on plan and not exc 1.5M in depth and getting only out in Hard/dense soil complete all as specified

Excavation in trenches in soft/loose soil , not.exc 1.5 mtr wide and not.exc 1.5 mtr deep and getting out in soft/loose soil for laying of cable/foundation of pole and stay etc in complete as sepecified.

Removing excavated materials not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above ground level from starting point.

Returning, filling including spreading, levelling, watering and well ramming in layers n.exc 25 cm complete all as specified and directed

M&L for sand cushioning in trenches/floor for protection including watering and consolidation all as specified and directed

Supply and Laying Bricks old size sub class 'B', of class designation 10, for the protection of cable laid flat dry across the cable complete all as specified.

S&F Bricks, sub class B, laid flat, in floors, old size bricks laid dry complete all as specified and directed

S&F in replacement of switch flame proof rotary type with termination box in LM6 , 16 Amps , single pole 240 volts complete all as specified.

Supply and fixing in replacement of LED flameproof fitting 2x18Watt , Degree of Protection : IP-66 Protection As per IS/IEC 60529:2001, Material of Construction : Aluminium Alloy LM-6, Area classification -GAS Group I, IIA & IIB & IIC As per IS/IEC 60079-1:2007, Gas group -I, IIA & IIB & IIC, Glass : Heat Resistant & Stress Free, Borosilicate Type clear Glass, Cable Entry : 3/4"ET - 02 Nos.complete

M&L Preperation of old painted Steel surface of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of Red oxide primer all as specified and directed by Engineer -in-charge

Supply and fixing in replacement of new generation energy saving environemental friendly long life exclusive innovative die cast aluminium IP65 LED flood light with high power LEDs as light source of capacity 120 Watt complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement LED Street Lights 72 Watt, CCT not less than 5700k and Efficacy not less than 110lm/W with Potted Driver of pressure die-cast aluminium housing street lights have clear toughened glass diffuser and bottom opening driver compartment. It comes up with secondary optics and individual high power LEDs for better light distribution and control. K08 street light with IP66 degree of protection and Potted Driver with 5KV internal and 10KV external surge protection alongwith 40mm dia Medium Grade GI Pipe of 1mtr with bracket and stand for fixing in wall complete all as directed and specified by Engr-in-charge.

S& F in replacement of MCCB 63Amp, 4Pole,415V ,36KA (Conforms to IS/IEC:60947-2) MCCB with Thermal Magnetic Protection Unit , Range – 16A to 630A , Ics = 100% Icu ,Thermal Adjustable – 0.8 to 1 In, Magnetic Adjustable – 5 to 10 In starting from 50A all as specified and directed by Engr-in-charge

S& F in replacement of MCCB 100Amp 4Pole,415V ,36KA (Conforms to IS/IEC:60947-2) MCCB with Thermal Magnetic Protection Unit , Range – 16A to 630A , Ics = 100% Icu ,Thermal Adjustable – 0.8 to 1 In, Magnetic Adjustable – 5 to 10 In starting from 50A all as specified and directed by Engr-in-charge

S& F in replacement of MCCB 160Amp 4Pole,415V ,36KA (Conforms to IS/IEC:60947-2) MCCB with Thermal Magnetic Protection Unit , Range – 16A to 630A , Ics = 100% Icu ,Thermal Adjustable – 0.8 to 1 In, Magnetic Adjustable – 5 to 10 In starting from 50A all as specified and directed by Engr-in-charge

S& F in replacement of MCCB 250Amp 4Pole,415V ,36KA (Conforms to IS/IEC:60947-2) MCCB with Thermal Magnetic Protection Unit , Range – 16A to 630A , Ics = 100% Icu ,Thermal Adjustable – 0.8 to 1 In, Magnetic Adjustable – 5 to 10 In starting from 50A all as specified and directed by Engr-in-charge

M&L for Cleaning of pump house from inside and outside in every month duly taking out unwanted material grass/vegetation/roots etc all as specified and directed by Engr-in-charge. Note : Rate include cleaning of 5 pump house to be treated as a one job. Tools required for cleaning will be provided by the Contractor

M&L for spraying of chemical (roundup) around pump house in the ration 1:3 for burning of grass as an when required complete all as specified and directed by Engr-in-charge

M&L for PCC in foundations, filling and mass-concrete 1:3:6 type-C2 using 40 mm graded stone aggregate complete all as specified and directed

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft & raft beams, sides & soffits of foundation & plinth beams; and similar work; verticle or to batter fair finished surfaces of concrete flat complete all as specified and directed.

S& F of Double Walled Corrugated Pipe (DWC) conforming to IS:14930 (Part-II) /IS 16205 Part II of Size 160/136 colour of pipe outer & Inner is of orange all as specified and directed by Engr-in-charge. Make : Dutron / Supreme / SFMC/ Tirupati or equivalent approved in MES by any Command.

S& F of Double Walled Corrugated Pipe (DWC) conforming to IS:14930 (Part-II) /IS 16205 Part II of Size 110/95 , colour of pipe outer & Inner is of orange all as specified and directed by Engr-in-charge. Make : Dutron / Supreme / SFMC/ Tirupati or equivalent approved in MES by any Command.

S& F of Double Walled Corrugated Pipe (DWC) conforming to IS:14930 (Part-II) /IS 16205 Part II of Size 300/260, colour of pipe outer & Inner is of orange all as specified and directed by Engr-in-charge. Make : Dutron / Supreme / SFMC/ Tirupati or equivalent approved in MES by any Command.

S& F of Double Walled Corrugated Pipe (DWC) conforming to IS:14930 (Part-II) /IS 16205 Part II of Size 90/76 colour of pipe outer & Inner is of orange all as specified and directed by Engr-in-charge. Make : Dutron / Supreme / SFMC/ Tirupati or equivalent approved in MES by any Command.

S&F Insulation mat long-lasting, easy to install, clean an anti-skid a strong grip mat which is resistant to oils, acids, alkalis . low temperature and are flame retardant as per the provisions of IS 15652:2006.of thickness 2.5mm, Class B having 100% shock proof under leakage current 10 mA all as specified and directed by Engr-in-charge. Make :- Jyoti / Aicon / Vardhman or equivalent confirming to IS specification. Note: Test certificate from a Govt registered company should be submitted before installation.

S&F Insulation mat long-lasting, easy to install, clean an anti-skid a strong grip mat which is resistant to oils, acids, alkalis . low temperature and are flame retardant as per the provisions of IS 15652:2006.of thickness 2mm,mat size , Class A having 100% shock proof under leakage current 10 mA all as specified and directed by Engr-in-charge. Make :- Jyoti / Aicon / Vardhman or equivalent confirming to IS specification. Note: Test certificate from a Govt registered company should be submitted before installation.

Taking out old steel tubler poles 9 mtr by breaking PCC foundation, and all related work and making the site well finished and Shifting of Pole to another location within 54 ASP area (i.e.Tech Area/G Block/admin area/H-block, D-camp etc) complete all as specified and as directed by Engr-in-charge.

M&L for Fixing steel tubular pole single arm type 9 M retrieved from item No 73 hereinbefore including excavation in trenches in soft/ loose soil n exc1.5 M wide and net exc 1.8 M in depth and triming the sides , boring bottom surfaces to required level, providing PCC (1:3:6) type D-2 using 40mm stone agregate in foundation, 1.5 mtr GI pipe medium grade of 40mm dia for cable protection and PCC 1:2:4 type B-1 coping of pole including neccessory frame work complete all as specified and as directed by Engr-in-charge.

S&F Casing Caping PVC Size 25 mm alongwith nails complete all as speciified and directed by Engr-in-charge

M& L for laying of Gravels/stone of size 40mm each complete all as specified and directed by Engr-in-charge Note: Gravels/stone should not be plane,cut or broken. All Stone/Gravels must be clean.

Supply, installing, testing and commissioning factory made and tested in replacement of LT panel of any type to LT Panel Outdoor type of size 1050 X 450 X 1200 mm ( LxWxH ), platform mounted, suitable for 415 Volts 3 Phase and neutral, 4 wire, 50Hz AC supply system having bus bar chamber with insulated electrolytic Aluminium bus bars TPN of capacity 200 Amps rating installed on DMC insulators with bus bar chamber. The panel shall be dust and vermin proof, and made out of 3.15 mm thick CRCA mild steel sheet and mild steel & Angle frame work of 50 X 50 X 6 mm ), front opening type with proper ferrule & cable gland, internal wiring with PVC insulated multistranded copper conductor FRLS cable of adequate size but not less than 1.5 sqmm complete. All steel metal works including frame shall be with anticorrosive coating with seven tank process and finally epoxy polyester powder coating of Siemens grey RAL- 7035 shade complete with necessary PCC 1:3:6 foundation work as directed at site. The scope of work also comprising of the following:- Make of Panel: Unilac/ Schneider / Advance Switch Gear Control/ Tricolite.

Sevicing & Replacement of parts of Air blower complete all as specified and directed by Engr-in-charge Note:-Parts is included in separate sch of work

Bearing Serial No 6307-2Z-C3

Bearing Serial No 6306-2Z-C3

Oil Seal

Safety relief Valve

Lubrication Oil

Note :- The amount of Rs 100834/- against Schedule of Credit on Srl Page 151 & 152 shall be deducted from the total amount quoted against Sch 'A'

A B K Enterprises (BID ID -3392324)

M/S PARKASH ENTERPRISES (BID ID -3390120)

M/S Anand Enterprises (BID ID -3390652)

Sumit Enterprises (BID ID -3391322)

SM CONSTRUCTION COMPANY (BID ID -3393608)

PARAS ENTERPRISES (BID ID -3392882)

S.R. Constructions (BID ID -3393101)