SPL REPAIR TO BLDG NO T-23 UNDER GE (EAST) MATHURA

Demolition of cement concrete (unreinforced) in ground floor and pavings not exc 15 cm thick (below or above ground level) including floor tiles of any description complete all as specified & as directed.

Demolition of reinforced cement concrete in roof, floor (other than ground floors), beam, staircases, landing, chajjas and similar suspended work including removing rubbish out side of MoD land (reinforcement cut as required to facilitate demolition) not otherwise specifically provided for in this Schedule, complete all as specified & as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Taking down cement plaster or cement lime plaster, terrazo etc on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc, complete all as specified and as directed.

Dismantling wall and ceiling boards (fiber, pulp, insulation, etc) or insulation board/slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed.

Dismantling timber scantling 40 sqcm and over in section in framed work in any position complete all as specified and directed.

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins etc. under 40 sqcm in section, framed work complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description and from any position not otherwise provided for in this Schedule complete all as specified and as directed and directed.

Taking down chowkat or frame with shutters (including fittings & fixtures) area not exc 1.5 Sqm each (without taking off the shutters from the frame) of door/window including cutting holes for taking out hold fasts and making good the same including disturbed portion of jambs, cills, etc complete all as specified and as directed.

Taking down chowkat or frame with shutters (including fittings & fixtures) area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the shutters from the frame) of door/window including cutting holes for taking out hold fasts and making good the same including disturbed portion of jambs, cills, etc complete all as specified and as directed.

Excavating in trenches, not exc 1.5 metre wide and not exc 1.5 metre in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. laying cables, pipes, etc. not exc 10 Sqm on plan & not exc 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil complete all as specified and as directed.

Removing excavated soil/material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified and as directed.

M&L for cement concrete 1:2:4 type B0, using 12.5mm graded crushed stone aggregate as in roof kerbs or mud stops, coved fillets, lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates and the like including weathering, slightly rounded, chamfered angle and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair complete all as specified & as directed.

M&L for factory made Precast RCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in landings, cover slabs, consisting of size (1.20x0.6m) and (0.50x0.90m) (for man holes, drains etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including placing in position and set in CM (1:6) complete all as specified & as directed.

Supply only integral liquid water proofing compound (ISI marked) complete all as specified & as directed.

M&L for brick work with old size burnt clay sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement and sand mortar 1:4 complete all as specified and as directed.

M&L for 50mm thick sand stone slab set and jointed over supports as in chajjas of ground and first floor's over windows, doors etc and jointed in cement mortar 1:4 complete all as specified and as directed.

M&L Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45x70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-in-Charge.

S&F 12mm thick Rajshri WPC board of plain white (Matt finish) colour fixed with screws, solvent cement/ adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete as per specifications and as directed by the Engineer-in-Charge.

S&F 18mm thick WPC board both side decorative fixed with screws, solvent cement/ adhesive/bolts to make kitchen cabinet sides top and bottom and shelves inside the cabinets etc. complete as per specifications and as directed.

S&F 18mm thick Rajshri WPC board of Single Side Prelam/ Rigidlam color fixed with screws, solvent cement/ adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinets complete as per specifications and as directed by the Engineer-in-Charge.

M&L for built in steel cup board with pressed steel frame of size 75mmx45x1.25mm thick with pressed steel shutter 1mm thick Godrej pattern fixed to masonary wall by hold fast made out of 25x3mm flat iron including MS hanging rod of 10mm dia with bracket fixed on inner side of one leaf of shutter and on the other leaf provision of MS peg set of three pegs including spray incl locking arrangement painting with two coats of synthetic enamel paint over one coat of red oxide primer all around on steel surface of frame and shutter and making good disturbed portion in cement and sand mortar 1:3 or PCC 1:2:4 complete all as specified and directed.

S&F Stainless steel handles of size 150mm, fabricated type anodised complete all as specified and as directed.

S&F 75mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) fixed complete all as specified and as directed.

S&F Stainless steel barrel tower bolts 200mm length of bolt of extruded section and fixed complete all as specified and as directed.

Supply & fixing hasp and staple of size 100mm aluminium anodized safety type with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F 100mm long size of hinges, extruded aluminium alloy with galvanised mild steel hings pin anodized and fixed type B-21complete all as specified and as directed.

S&F auto closing hinges 35mm of 0 crank (KH-001) OR 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete all as specified and as directed.

S&F Stainless steel 250mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of stainless steel and fixed complete all as specified and as directed.

Supply and fixing Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

S&F in repairs stainless steel drapery rod of 25mm inner dia & 1.6mm wall thickness (in lengths as directed) with & including stainless steel sockets & decorative finial at both ends and pair of stainless steel brackets & stops fixed at both ends with PVC rawl plug & steel screws on walls/beam complete all as specified & as directed.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, framed signed boards, walk ways, railings, framework of water tanks and similar work including welding conforming to Grade E-165 (Fe 290), complete all as specified & as directed.

M&L for Mild steel work in tubular trusses, purlins, vetical posts including special shaped washer, angle cleats, fish plates, gusset plates, base/ bearing plates, bolts and nuts etc. complete using ERW or induction butt welded tubes conforming to 1161-1979 grade st 240 complete all as specified and as directed.

S&F rolled mild steel as in Joist, channel, angle or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length directed) and similar work conforming to Gde E-250 (Fe 410-W) quality `A’ complete all as specified and as directed.

S&F anodized aluminium frame for doors, windows, ventilators, partitions, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified & as directed.

S&F anodized aluminium door shutters, aluminium section weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminum snap beading screws etc. complete all as specified & as directed.

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116x45mm & sash 46x62mm both having wall thickness of 2.3 ± 0.2mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 Kg), G.I fasteners 100x8mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F Pre-painted galvalume aluminium zinc coating corrugated steel sheet 0.50mm thick with coating AZ-150 gsm of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of old AC asbestos sheet complete all as specified & as directed. Note : Colour of sheet shall be as approved by the GE.

S&F Pre-painted galvalume aluminum zinc coating Plain steel sheet 0.50mm thick with coating AZ-150 gsm of any colour having tensile strength of 550 Mpa as in roof covering/ridge/fascia/cladding to wall, fixed with self tapping screws including dismantling of old AC asbestos sheet complete all as specified & as directed. Note : Colour of sheet shall be as approved by the GE.

S&F for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre complete all as specified and directed.

M&L for Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions including providing two coats of wall care putty over ceiling board and including two coats of distemper oil emulsion complete all as specified and directed. Note:- Rates of wall care putty and distemper included in this item and no extra payment will be made separately

M&L for 100mm thick PCC (1:4:8) type D2 using 40mm graded crushed stone aggregate as in sub base complete all as specified and as directed.

M&L for non skid coloured ceremic ENDURA tiles 400x400x15mm thick set and jointed in neat cement slurry & pointed with coloured cement to match in floor over and including 15mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for 25mm thick PCC (1:2:4) type B0 using 12.5mm graded crushed stone aggregate as in flooring/padding, leveling course, etc, surface finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 16 to 18mm thick Granite slab work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like laid over and including 20mm thick screed bed in cement and sand mortar 1:4 and pointing in white cement (1:2 ) using marble dust with admixture of pigment to match with shade of granite, including rounded/half rounded edge and providing hole for gas pipe in pre-cast slab as well as in granite slab of cooking platform including dismantling of old U/S stone slabs and tiles etc. complete all as specified and directed. Note : The exposed edges of granite stone slab shall be made full round & polished to mirror finish and rate quoted shall deemed to include this provision.

M&L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) size of tile 600x1200mm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:4 including dismantling of old U/s tiles, hearth etc complete all as specified and as directed.

All as per serial item No. 48.00 here-in-before but as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over & including 10mm thick rendering in cement & sand mortar 1:4 including dismantling of old U/s tiles, hearth etc complete all as specified and as directed.

M&L for non skid ceramic tiles (coloured) 10mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:4 including dismantling of old U/s tiles, hearth etc complete all as specified and as directed.

M&L for double charged vitrified ceramic tiles 9-10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 including dismantling of old U/s tiles, hearth etc complete all as specified and as directed.

M&L for glazed ceramic tiles (coloured) 7mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm (i.e 600mm x 300mm or as directed), on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 including dismantling of old U/s tiles, hearth etc complete all as specified and as directed.

Supply and laying 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified & as directed.

M&L for 50mm thick PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate as in plinth protection surface finished even and smooth without using extra cement complete all as specified and directed. Note :- Plinth protection shall be of width as directed and shall be laid with an outward slope of 1:30 in alternative bays not exceeding 3 meter in length and grooves at corner. Joints of 6mm wide and 10mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

M&L for rendering 15mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, mixed with integral liquid water proofing compound as per manufacturer’s instructions, finished even & smooth without using extra cement, complete all as specified and directed. Note : Supply only integral liquid water proofing compound shall be measured and paid for separately.

M&L for preparation of newly plastered / unplastered surfaces of walls & applying one coat of alkali resistant priming paint on walls complete all as specified and directed.

M&L for providing one coat of wall care putty complete all as specified & as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil Bound distemper (OBD) of approved shade/tint over a coat of alkali resistant primer on wall complete all as specified & as directed.

M&L for complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including smooth finish white wall care putty on walls complete all as specified & as directed.

M&L for applying two coats of exterior emulsion exterior paint Apex over a coat of 2mm thick wall care putty as approved by GE complete all as specified and directed.

S&F 5mm thick sheet glass, ordinary quality and fixing with rubber beading area n exc. 0.5 square metre in each pane etc complete all as specified and as directed.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified & as directed.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, including taking up or down steel water tubing and connections of 15mm bore complete all as specified and as directed.

M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, including taking up or down steel water tubing and connections of 20mm bore complete all as specified and as directed.

M&L for galvanized steel water tubing medium grade of 25mm bore with & including all fittings, fixed to walls and ceilings or laid in floors, including taking up or down steel water tubing and connections of 25mm bore complete all as specified and as directed.

M&L for cutting chases, pinning in, making good to facings as original where required and pointing in cement and sand mortar 1:3 to end to edges of landings, steps, cills, sunshedes, shelves, lintels and cuttings chases for concealed water tubing etc. and making good, cutting not exc 10 cm girth in brick walls. complete all as specified and as directed.

Disconnecting & taking down the existing unserviceable water tank and Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed. Note : (i) The water storage tanks shall be 3 layers, HDPE tanks moulded to seem-less perfection of rotational process. The tanks shall be manufactured only from FDA approved special grade of polyethylene and shall be certified fit for potable water. (ii) The tanks shall white coloured and ISI marked. Also refer paras 18.6 and 18.6A of MES Schedule Part-I. (iii) Payment for inlet, outlet and over flow pipes and ball valve shall be made separately. Howerver cost of providing necessary GI fittings such as nipples with check nuts for inlet and outlet pipes, GI plug with check nut for over flow pipe and 30cm long wash out pipe, GI 20mm nominal bore, medium grade and check nut for wash out pipes of size as per actual requirements as directed by Engineer-in-Charge shall be deemed to be included in the unit rates of this item.

Disconnecting & taking down the existing unserviceable water tank and Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed. Note : (i) The water storage tanks shall be 3 layers, HDPE tanks moulded to seem-less perfection of rotational process. The tanks shall be manufactured only from FDA approved special grade of polyethylene and shall be certified fit for potable water. (ii) The tanks shall white coloured and ISI marked. Also refer paras 18.6 and 18.6A of MES Schedule Part-I. (iii) Payment for inlet, outlet and over flow pipes and ball valve shall be made separately. Howerver cost of providing necessary GI fittings such as nipples with check nuts for inlet and outlet pipes, GI plug with check nut for over flow pipe and 30cm long wash out pipe, GI 20mm nominal bore, medium grade and check nut for wash out pipes of size as per actual requirements as directed by Engineer-in-Charge shall be deemed to be included in the unit rates of this item.

S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, ‘P’ trap setting the trap and pan in cement concrete and including 10 litre capacity PVC valveless syphonic action type low level flushing cistern having dual control flushing system and 32mm dia PVC flushing pipe complete including jointing to socket of flushing rim complete all as specified and as directed.

S&F fixed in repairs vitreous china wash down water closet pan (Pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified & as directed.

S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, including pillar tap, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified & as directed.

Supply and fixing in replacement of PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified & as directed.

S&F sink with drainage board made of stainless steel 1mm thick for Kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to brick wall, connecting union to pipe, overall minimum size 915mm x 460 mm with bowl size 410mm x 330mm x160 mm including 40mm dia waste pipe of polythelene of low or high density, 40mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete all as specified and as directed including taking down old unserviceable sink with fittings.

S&F in repairs stainless steel Kitchen plate rack of overall minimum size 28"x 32"x18" deep, with partitions for small/large plates etc, made out of stainless steel sheet 0.63mm, fixed with rawl plug and CP steel screws complete all as specified and as directed.

S&F in replacement of PVC connection 450mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified & as directed.

S&F in repairs 20mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete all as specified & directed.

S&F in replacement of bib taps cast copper alloy, chromium plated, fancy type long body with half turm handle having weight of bib tap should not be less than 450 gms or as per SSR Part-I specification for iron pipes15mm bore complete all as specified and as directed. Make : Jaquar, Cat Part No. KUP-CHR-35037/Cera Cat Part No. F-1003151/Kohler Cat Part No. K-16093 IN-4-CP.

S&F in replacement of two way angle cock cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipes 15mm bore dia weight of two way angle cock should not be less than 450 gms or as per SSR Part-I specification complete all as specified and as directed.

S&F in replacement of fancy type 15mm bore long body angular cock, cast copper alloy, chromium plated, fancy type with capstan head having weight of angular cock should not be less than 450 gms or as per SSR Part-I specification, screwed down, screwed both end for iron pipes complete all as specified and directed. Make:-Jaquar Cat PArt No. KUP-CHR-350553PM/CERA Cat Part No F-1014201/Kohler Cat Part No. K-801541N-4AV-CP.

S&F in replacement of 15mm size stop valve , cast copper alloy, chromium plated with long shank and cup concealed type , fancy type with capstan head, screwed down, screwed both end for iron pipes complete all as specified & directed.

S&F Swivel shower of size 200mm for fixing with 15mm pipe (minimum weight 40gms) including shower arm, 195mm long with bend of 45 degree with flange of PTMT any colour (minimum weight 40gms) complete all as specified and as directed.

S&F in repairs brass chromium plated Hand Shower (Health Faucet) with 8mm dia & 1.20m long stainless steel braided flexible tube and wall hook suitable for fixing to supply pipe of 15mm bore complete all as specified and as directed.

S&F in repairs stainless steel towel rack fixed with steel screw etc complete all as specified and as directed.

S&F in repair PVC glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

S&F in repairs PVC corner of 3 piece set size 300mmx300mmx8mm thick, bevelled on edges with two brackets CP complete all as specified and as directed.

S&F in replacement of 110mm bore PVC (SWR type A) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified & as directed.

S&F in replacement of 75mm bore PVC (SWR type A) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified & as directed.

S&F in replacement of 110mm bore PVC (SWR type A) pipes single socketed in any length with rubber ring joints / solvent cement joints fixed to walls complete all as specified & as directed.

Supply and fixing 110mm bore PVC (SWR) plain bends any radius complete all as specified & as directed.

Supply and fixing 75mm bore PVC (SWR) bends any radius complete all as specified & as directed.

Supply and fixing 75mm bore PVC (SWR) bends with access door any radius complete all as specified & as directed.

S&F 110mm bore PVC (SWR) single junction (single 'T' ) equal or unequal provided with access door complete all as specified.

Supply and fixing 110mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F in replacement of PVC floor trap plain 75mm dia of outlet with grating including jointing with solvent cement complete all as specified and as directed.

S&F 32mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 Kgf/cm2 and fittings, fixed to WHB, complete all as specified and directed.

M&L for 150mm bore, grade 'A' reinforced concrete pipe, class NP-2, laid in trenches and jointed with cement and sand mortar (1:1) complete with collars including demolition and breaking up drain pipes 150mm bore drain pipe set in cement mortar complete all as specified and as directed.

Material and labour PCC 1:4:8 type D-2 using 40mm graded stone aggregate in bedding to drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150mm bore pipe complete all as specified and as directed.

M&L for cement concrete (1:2:4) type B1 using 20mm graded crushed stone aggregate as in surface channels and drains and benching including finishing the top of benching even and smooth using extra cement complete all as specified & as directed.

Taking down carefully existing unserviceable/perished surface conduit/concealed conduit/ batten/casing caping aluminium/copper point wiring any type for light, fan, bell, socket, power point etc complete including all fixtures and fittings such as batten/conduit/casing caping, switches, sockets, ceiling rose, pendent holder, lamp holders, bracket holders, light fittings, top sheet covers, fan regulators, wooden boxes, MS sunken boxes, etc and making good the disturbed surfaces of wall, floors, ceiling, etc to match with the adjoining surfaces, complete all as specified and as directed.

M&L for Modular point wiring for one light/fan/bell/buzzer point controlled by one, one way switch with 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including non-metallic rigid PVC concealed conduit (medium duty, ISI marked, not less than 20mm dia) with all fittings such as tee, bends, etc all as per IS, terminated in & including new modular metal flush boxes of requisite module concealed in wall for mounting fittings like modular switches, sockets, regulators etc with and including modular cover plates with frame of requisite module, complete all as specified and as directed. Notes : (i) Cost of cutting/leaving forming chases for conduits, sinking for modular metal flush boxes and making good in CM 1:4 shall deemed to be included in quoted rate of this item. (ii) The quoted rates of this item shall deemed to include for modular metal flush boxes of requisite module and modular cover plates with frame of requisite module of colour as approved by GE.

All as per serial item No. 101.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board with other switches complete all as specified and directed.

All as per serial item No. 101.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board complete all as specified and directed.

All as per serial item No. 101.00 here-in-before but for one 3 pin/5 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 4 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) including 4 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour complete all as specified and directed.

S&F Modular switch 1 way 6 Amp, 1 module, complete all as specified and as directed.

S&F Modular switch, 1 way 16 Amp, 1 module, complete all as specified and as directed.

S&F Modular Socket, 6 Amp - 2 in 1, 5 pin combined 2 module, complete all as specified and as directed.

S&F Modular Socket 6 Amp/16 Amp - 2-in-1, 3 and 5 pin combined 2 module, complete all as specified and as directed.

S&F Modular Fan step regulator, 120 Watt - 2 module, complete all as specified and as directed.

S&F ceiling rose, PVC/Polycarbonate insulated body, 65mmx50mm with three terminals, ISI marked, complete all as specified and as directed.

S&F lamp holder, PVC/Polycarbonate insulated body with back plate suitable for conduit/casing caping fittings, ISI marked, complete all as specified and as directed.

Supply & fixing in replacement of indoor decorative ultra slim surface /Wall mounted LED batten tube light complete fitting 1x20 watt LED Tube fitting with polycarbonate channel housing & integrated electronic driver,energy efficient, 140 Volt-270 Volt, co-related colour temperature (CCT) of 6500 K, >100 Lm/Watt complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing in replacement of indoor decorative ultra slim surface/ wall mounted LED batten tube light fitting complete, 1 x 10 watt with polycarbonate channel housing & integrated electronic driver, energy efficient, 140V-270V volts, corated colour temperature (CCT) of 6500K, > Lm/Watt complete with all accessories internally pre-wired and including connecting up with PVC insulated PVC sheathed twin core flexible copper conductor cable of suitable size complete all as specified and directed by Enginee-in-Charge.

Supply and fixing LED retrofit lamp 9 Watt complete all as specified and as directed.

Supply and Fixing in replacement of Light Emitting Diode (LED) based street/security light fitting, 30 Watt with & including LED lamp, housing made up of LM6 pressure die cast aluminium alloy with effective thermal management, sturdiness, monolithic construction, totally enclosed, dust and water proof, minimum system efficiency of more than 100 lumens per watt and a minimum system lumen output of not less than 2500 lumens, correlated colour temperature shall be minimum 5700 degree Kelvin, Colour Rendering Index (CRI) shall not be less than 70, fitting shall be designed for a system life of 50,000 hours @ 70% lumen maintenance, ingress protection of IP-65 (minimum), mechanical impact resistance rating of IK ≥ 07, operating voltage range 140 V to 270 V, AC, frequency 50-60Hz, potted type for humming free operation, driver shall withstand upto 400 V for 08 hours, surge protection not less than 10 KV, Power factor > 0.95, Total Harmonic Distortion (THD) shall be less than 15%, double phase protection, no load, open circuit and short circuit protection, suitable for ambient temperature from (-)10°C to 50°C and humidity level 10% to 90% RH, cool white colour and lamp starting time shall not be more than 10 second, PMMA/ polycarbonate/toughened glass heat resistant cover, prewired and connecting up to street light feeder/junction box with & including 2.5 Sqmm 3 core PVC insulated, weather proof, multistranded copper conductor cable of 1100 Volt grade (ISI marked), complete all as specified and as directed.

Supply and Fixing in replacement of Light Emitting Diode (LED) based recessed type panel light, (600x600) colour, 35/36 Watt with warm/white complete with fittings intergrated electronic driver, energy efficient 230 Volt, 50 Hz, corelated colour temperature (CCT) of 6500K, complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of 1100 Volt grade (ISI marked), fixed complete all as specified and as directed.

NOTES FOR LED LIGHT FITTINGS : (i) All LED light/luminare shall meet the provision laid down in IS - 16101, 16102 Part-I/II, 16103 Part-I, 16104, 16105, 16106, 16108/2012 and 15885 Part -II / Section 13. (ii) Contractor shall submit test report of LED street light fitting from Government accredited test laboratory for LM-79 and LM-80. (iii) Contractor has to furnish a replacement warranty of 05 years for LED light fittings complete including lamps from the date of completion of contract. The product will be replaced on site free of cost in the following case :- (a) Manufacturing defects. (b) Failure due to mechanical and electrical impact. (c) Drop in lumen (or lux at 1 m) below 90% of claimed values of lumen (or lux at 1 m) of the LED /Luminaries.

M&L for building security light bracket made out of 40mm dia light grade GI pipe of 1.20m length bent to required shape suitable for fixing street light fitting on Steel tubular pole/wall including two Nos clamps made out 40mmx6mm flat with suitable nuts and bolts including two coats of aluminium paint over a coating of red oxide primer complete all as directed.

S&F in replacement of Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp, 230 Volt, 10 kA, ‘C’ Curve, fixed, complete all as specified and as directed.

S&F sheet metal enclosure for distribution boards flushed in wall, double door type, IP-43 protection, IK-09 with metal door suitable for fixing MCBs/MCCBs, 415 Volts with 200 Amps rated bus bar, load line DB fitted with bus bar neutral links blank plates, VTPN, DB, vertical load line, 6 way, 415 Volts, suitable for G frame MCCB 160 Amp as incomer, fitted with and accessories, including taking down old existing unserviceable DB with fixtures of any type complete all as specified and as directed. Note : Cost of cutting/leaving forming chases for sinking for DB and making good in CM 1:4 shall deemed to be included in quoted rate of this item.

S&F sheet metal enclosure for distribution boards flushed and surface mounting, double door type (IP-43 IK 09 with metal door), suitable for fixing MCBs, 240 Volts with 200 Amps rated bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar, DB fitted with bus bar neutral links blank plates, SPN, 12 way, suitable for MCBs, fitted with and accessories, including taking down old existing unserviceable DB with fixtures of any type complete all as specified and as directed. Note : Cost of cutting/leaving forming chases for sinking for DB and making good in CM 1:4 shall deemed to be included in quoted rate of this item.

S&F sheet metal enclosure for distribution boards flushed and surface mounting, double door type (IP-43 IK 09 with metal door), suitable for fixing MCBs, 240 Volts with 200 Amps rated bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar, DB fitted with bus bar neutral links blank plates, SPN, 8 way, suitable for MCBs, fitted with and accessories, including taking down old existing unserviceable DB with fixtures of any type complete all as specified and as directed. Note : Cost of cutting/leaving forming chases for sinking for DB and making good in CM 1:4 shall deemed to be included in quoted rate of this item.

S&F in replacement of MCB, 6 to 32 Amps, Single Pole (SP), 240 Volts, rupturing capacity not less than 10 kA, ‘C’ Curve, with over load and short circuit protection, complete all as specified and as directed.

S&F in replacement of MCB, 40 Amps, Single Pole (SP), 240 Volts, rupturing capacity not less than 10 kA, ‘C’ Curve, with over load and short circuit protection, complete all as specified and as directed.

S&F in replacement of MCB, 32 Amps, Single Pole with neutral (SPN), 240 Volts, rupturing capacity not less than 10 kA, ‘C’ Curve, with over load and short circuit protection, complete all as specified and as directed.

S&F in replacement of MCB, 40-63 Amps, Single Pole with neutral (SPN), 240 Volts, rupturing capacity not less than 10 kA, ‘C’ Curve, with over load and short circuit protection, complete all as specified and as directed.

S&F MCCB 4 Pole 160 Amps, thermal magnetic having, breaking capacity 25 KA, 415 Volt in the existing position new MCCB & making connections with 25x3 mm copper strip as required, making necessary and connections including disconnecting & taking down old unserviceable MCCB, complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 7.50 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40 mm thick RCC pit cover, etc including dismantling & taking out old existing unserviceable earthing complete all as specified & as directed. Note : PCC chamber shall be constructed at least 1.5 mtr away from the earth electrode and pipe for watering shall be provided in slanting manner.

Supply and fixing Exhaust Fan made of sturdy Engineering plastic complete with louvers shutter, 250mm sweep, 230 Volts, 50 Hz, 1200 RPM, copper winding and connecting with & including 1 Sqmm, three core, flexible multi stranded copper conductor cable and connected from ceiling rose to exhaust fan including cutting holes for air ducting of exhaust fan in circle/square shape or as per site complete all as specified & as directed.

Supply, assembling, hanging, fixing & testing Ceiling Fan of size 1200mm sweep, single phase, AC supply, 230 Volt, with & including complete accessories, down rod, canopies, three number blades, capacitor 2.5 mfd, hook, rubber reel, safety pins, nuts, bolts, washers, cable connector and making connection with PVC insulated & sheathed 1 Sqmm three core flexible copper multistranded conductor cable (ISI marked) from ceiling rose to connector of ceiling fan including marking of SM / MES number with thick synthetic enamel paint of approved tint complete all as specified and as directed. Note :- The font, style & place of writing SM/ MES number with synthetic enamel paint on ceiling fan shall be as directed by the Engineer-in-Charge and cost thereof shall deemed to be included in quoted rates.

M&L for sub main wiring with two runs of 10 sqmm (nominal area) size main cable & one run of 10 sqmm size earth continuity conductor, single core, PVC insulated, unsheathed, FRLS with multi-stranded copper conductor, 1100 Volts grade, ISI marked cables, drawn through & including suitable size of heavy duty non-metallic rigid PVC concealed conduit ISI marked not less than 25mm dia & conduit fittings/accessories, fixed concealed in wall/ceiling including dismantling & taking down old unserviceable sub main wiring complete all as specified and directed. Notes :- (i) 02 runs of 10 sqmm size main cable, 01 run of 10 sqmm size earth continuity conductor cable & conduit with accessories shall be measured as one run length for payment purpose. (ii) Cost of cutting/leaving forming chases for conduits and making good in CM 1:4 shall deemed to be included in quoted rate of this item.

Supply, laying, jointing and testing LT XLPE insulated screened, bedded, galvanised steel strip or wire armoured heavy duty electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 50 sqmm 4 core laid in trenches/ducts, through HDPE double wall corrugated pipe (out dia should not be less than 40mm), including connecting with suitable lugs, glands, nuts and bolts in existing panel from pole/ main panel box and testing complete all as specified and directed. Notes :- (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately. (ii) Road cutting/floor cutting/cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing and HDPE pipe rate shall be deemed to be included in quoted rate. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions.