Renovation of CCR Toilet at 9 M elevation at Plant area of AGBPS NEEPCO Bokuloni Dist Dibrugarh Assam

Amount

Wall Painting with plastic paint emulion paint of approved brand and manufacture to give an even shade. One or more coats on old work.

12 mm cement plaster of mix 1:4 1 cement : 4 fine sand

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved brand and manufacturer , in all colours and shade, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, levelling system and rubber mallet for placing the tiles gently and easily Glazed Vitrified tiles Matt / Antiskid finish of size Size of Tile 600 x 600 mm

Providing Kajaria bathroom wall tiles, 8 mm thick and fitting fixing in position at site in all respect.

Providing and fixing tiled false ceiling of specified materials of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grms / sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24 x 38 mm made from 0.30 mm thick (minimum sheet), spaced at 1200 mm centre to centr and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum sheet), 1200 mm long spaced between main "T" at 600 mm long centre to centre to form a grid of 1200 x 600 mm and secondary cross "T" of length 600 mm and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlockedat middle of the 1200 x 600 mm panel to form grids of 600 x 600 mm and wall angle of size 24x24x0.3mm and laying false ceiling tiles of approved texture in the grid including, required cutting / making, opening for services like diffusers, grills, light fittings, fixtures smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasterners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x30x0.8 mm spaced at 1200 mm centre to centre along main T, bottom exposed width of 24 mm of all T-Sections shall be prepainted with polyster paint, all complete for all heights as per specifications, drawings and as directed by the Engineer-in-Charge. 12.5 mm thick fully Perforated Gypsum Board tile made from plaster board having glass fibre conforming to IS : 2095 Part I , of size 595 x 595 mm, having perforation of 9.7 x 9.7 mm at 19.4 mm c/c with centre borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing.

Providing vitreous China wash basin with CI/MS brackets, CP brass chain with plug, PVC waste e pipe including painting of fittings and brackets, cutting and making good the walls wherever required (Pillar cock, stop cock waste coupling are to be paid separately) Table top Basin Hindware Rubbic Table Top Wash Basin

Providing fitting and fixing vitreous china division plate including fitting and fixing complete as directed and specified.as directed and specified. Hindware Make (a) White (i) New Division Plate (Cat No. 61005)

Providing fitting and fixing vitreous China Dual Flush / Floor Mounted Coupled / Extended water closer (European type W.C. Pan 400 mm high) with seat and lead, CP brass hinges and rubber buffers, CI/MS brackets, 40 mm dia flush band with fittings including painting of fittings and brackets required (Flushing Cistern to be paid separately). Make: Hindware White One Piece water closet Cataloge No - ID - 92085 Size 69 x36 x74

Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe.

Providing, fitting fixing flush valve for Urinal basin complete as directed and specified Neo Flush Valve - 32 mm single Flush (Round) Make: Hindware Cat No.: F860037 CP

Providing fitting and fixing white vitreous china flat back type lipped front urinal basin with standard flus pipe and CP brass spreader and brass unions, complete including painting of fittings and brackets, cutting and making good the wall and floor wherever required. Hindware Make (i) White Riva (Cat No 9003)

Providing and fixing Chlorinated Polyvinyl Choride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one ste[p CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in- Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal dia pipe

Providing fitting and fixing Decorative Mirror complete as directed and specified. Make: Shreeji Glass (i) Model L43 (a) Size 800 x 600 mm

Providing and fixing P.T. MT Waste Coupling for wash basin and sink, of approved quality and colour. Waste Coupling 38 mm dia of 83 mm length and 77 mm breath, weighing not less than 60 gms.

Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fitting complete. Flexible pipe 40 mm dia

Providing and fixing C. P. Brass long nose bib cock of approved quality conforming to IS standard and weighing not less than 810 gms. 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS: 8931. 15 mm nominal bore

Supplying and fitting fixing C.P pillar cock of 15 mm dia of approved brand as specified and directed. Make: Jaquar Alive Pillar Tap Deck Mount

Providing fitting and fixing C.P. soap tray / soap dish complete as directed and specified. Jaquare Soap Dish Holder AKB CHR 35731

Providing fitting and fixing CP towel ring complete as directed and specified Jaquare Make Towel ring Square Kubix prime Code: AKP-CHR-35721P

Providing fitting and fixing Automatic hand Drier as directed and specified. Automatic Hand Dryer EH22NWABS Make: EURONICS

Providing fitting and fixing Liquid soap dispenser and liquid soap container complete as directed and specified. Jaquar Make Kubix Prime Akp - 3573p soap Dispenser with Glass.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10mm to 25 mm

Providing and fixing 100 mm sand cast Iron grating for gully trap

Providing and fixing stone slab with table rubbed, edges rounded and polished of size 75 x 50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-Charge and finished smooth Granite stone of approved shade

Providing and laying in position specified grade of rinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Centering and shuttering including strutting, proppings etc. and removal of form for Walls (any thickness) including attached plasters, butteresses, plinth and string courses etc.

Providing and fixing toilet paper holder CP brass

Steel Reinforcemnet for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Mild steel and Medium Tensile steel bars

Providing and fixing aluminium work for doors, window, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other section of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust freee, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. (Glazing, paneling and dash fasterners to be paid for separately): For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powdre coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade I Type II, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides

Half brick masonry with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundation and plinth in : Cement mortar 1:4 (1 cement : 4 coarse sand).

Providing and fixing stainless steel pipe and fitting of grade 316L a per IS 6911:2017and conforming to EN - 10312 standards complete with press type fitting (fitting shall be paid for separately ) i/c fixing with the pipe with clamps at 1.00m spacing including cutting and making good the walls including testing of joints complete as per direction of Engineer-in-Charge (The pipe length inserted in the fitting shall not be measured for payment) 54 mm outer dia pipe

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction Engineer-in-Charge. Anodized (AC 15) aluminium

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete. i) Sliding Door bolts (a) 300 x 16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary scres etc. complete. etc. complete 200 x 10 mm

Bidder Name

Amount in Words

R M ASSOCIATE

DHIREN SAIKIA

KESHAB PHUKAN

M/S H G ENTERPRISE

DHIREN SAIKIA

R M ASSOCIATE

M/S H G ENTERPRISE