REPAIR MAINTENANCE OF MAIN RISING OF HIGH LOW RISE BLDGS AND ASSOCIATED WKS AT RASHI COMPLEX AREA NEW AND OLD NAVY NAGAR AND REPAIR MAINTENANCE OF FIRE FIGHTING SYSTEM AND CONNECTED WORKS AT OLD NEW NAVY NAGAR AREA JD BLDGS ASHA BLDGS RASHI AREA UNDE

Amount

Supply and Fixing in repairs steel water tubing, galvanised, Medium grade with all fittings such as nipple, union, socket, elbow, bends, fixed to wall up to 15 th floor in high rise buildings in shafts in short piece/length, including breaking the existing brick wall for replacement of corroded GI pipe in/on wall and making good the disturbed surfaces of following sizes complete all as specified and directed by Engineer-in-charge. Note: (i) Work shall be carried out in high rise buildings, plain wall, in shafts, in terraces, inside the flats for cutting the existing GI pipe line and replacing the same with new GI pipe in short piece or full length. (ii) The cost of providing scaffolding and safety measures to the employees shall be included in quoted rates.

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

80 mm bore

Supply and fixing in repairs gun metal gate valve with iron wheel head screwed both ends for iron pipe including fittings i.e. union, socket etc of following sizes complete all as specified :-

40 mm bore

50 mm bore

80 mm bore

Material and labour for Construction of brick masonary valve chamber of size 1200 mm x 1200 mm x 1200 mm (internal dimension) (above GL 0.30 mtr) suitable for fixing of sluice valves, 15 cm thick foundation using PCC 1:4:8 type D-2 over 15 cm thick hardcore of broken stone, 23 cm thick brick walls built in cement and sand mortar 1:4, 15 mm thick internal and external plaster including top of floor in cement and sand mortar 1:3 finished even and smooth without using extra cement, 8 mm thick MS plate cover on 75mm x 75mm x 8mm MS angle frame embeded in PCC 1:2:4 type B-1 coping of 50mm thick, having rectangular, hinged, opening of size 150mm x 100mm with locking arrangements ,hold fasts including applying one coat of red oxide zinc chrome primer and two coats of synthetic enamel paint to all steel surfaces including excavation and earth work in any type of soil including demolition of existing chamber and disposal of debris outside MoD land complete all as specified and directed by the Engr-in-charge

Supply,Installation Testing & Commissioning of Indoor type Programmable Logic Controller based Valve Automation and communication Panel suitable for control and/or monitoring of 02 Nos. Pumps, 02 Nos Pressure Transmitter, 02 Nos. Priming Motorised Valve, 03 Nos. Solenoid Valves, 7 Nos motorized valves (+02 Spare) and 06 Nos. magnetic sensors PrimingTanks-02(2 Levels), over head tank -04 including suitable number of energy meters and 01 Nos ULitreasonic level sensor, . The panel should be of suitable size fabricated from 2.0 mm thick CRCA sheet duly powder coated. The Panel should comprise the following items:- (a) Water Level Sensing & Display (b) Pump On/Off with switches/Indicators (c) Auto priming (d) Operation of Motor Actuated Butterfly Valves in automatic/manual mode (e) Automatic Toggling of Pumps (f) Auto Change Over In Case of Pump Failure (g) Single Phasing Prevention . (h) Manual Mode Operation of all connected sub systems including all valves (in pump houses and connected buildings / overhead tanks) and pumps from the PLC based Control Panel. The PLC based Panel shall consist of the follwing sub systems:- (a) 01 No.PLC with follwing specifications; (i) Suitable Digital inputs/ outputs (ii) 4 serial ports supporting open communication protocol, 01 No. Ethernet port. (iii) Programming software based on IEC to facilitate building of custom built function blocks. (iv) Expandable upto 192 DI / DOs. (b) 01 No SMPS of 5 A rating (Make: SCHNEIDER / NHP) (c) Suitable No of interposing relays 24 V D.C. coil rating, 4 pole and 2 A contact rating. (Make: OEN / OMRON / IDEC / ALLEN BRADLEY)

Notes for item No. 4 & 5:- To make the system fully functional. all panels shall be consisting of the following :- (a) Rack mountable Web Smart Switch with 28 ports and POE for CPE hardware and following specifications:- (i) Number of Ports 24 10/100Base-TX Ethernet ports 2, 10/100/ 1000BASE-T 2 Combo 10/100/1000BASE-T/SFP. (ii) Port Standard Supply and fixing functions • IEEE 802.3 10BASE-T Ethernet (twisted-pair copper) • IEEE 802.3ab 1000BASE-T Gigabit Ethernet (twisted-pair copper) • IEEE 802.3x Flow Control • IEEE 802.3u 100BASE-TX Fast Ethernet (twisted-pair copper) • IEEE 802.3z Gigabit Ethernet (fiber) ANSI/IEEE 802.3 • IEEE 802.3z Gigabit Ethernet (fiber) ANSI/IEEE 802.3 Switching Capacity • 12.8 Gbps Make : Siemens, Dlink, Ubiquiti, Cisco (b) Hot pluggable 1310 nm multimode/Single mode SFP (mini-GBIC) transceiver, supporting full duplex, Gigabit speeds on multimode/Single mode fiber for distances of up to 550m/550m/10km on 62.5µm/50µm/ 9µm respectively in a metal housing to reduce EMI and to increase durability Make : Dlink, Ubiquiti, Cisco, Siemens, HP (c) Rack Mountable LIU with the following specifications:- (i) Rack Mountable 12 Port Unloaded LIU (ii) Aluminium Base Material (iii) Slim 1 U mounting height (iv) Metal Shelf Aluminium 1.2 mm thick (v) Splice tray Aluminium 0.6mm (vi) Winding Panel – Plastic (vii) Cable Plug – Rubber for minimum 2 cable entries (viii) Adaptor Panel Aluminium 1.5 mm thick (ix) 2 fiber spools built in for 900 um tight buffered fibre storing (x) Capable of storing upto 3 mts of 900 um tight buffered fibre per adaptor Make : Dlink, Ubiquiti, Cisco (d) SC-LC Duplex SM Patch Cord 0.9 mm dia of suitable length (i) Size 0.9mm dia (ii) Insertion Loss <=0.2 db, max 0.3 db (iii) Return Loss PC>=45dB, UPC>=50dB, APC>=60dB (iv) Connector Ferrule Ceramic (v) Apex Offset <50um (vi) Fiber Height +-100nm (vii) End Face Radius of Curvature 7mm<R<25mm (viii) Repeatability <=0.2 dB 1,000 times mating cycles (ix) Working Temp -40deg C to +85 deg C Make : Dlink, Ubiquiti, Cisco

(e) SC Simplex Coupler/Adaptor (i) Insertion Loss <=0.2 dB for Zirconia Sleeve (ii) Sleeve/Ferrule Withdrawl Force 2.0N to 5.9N Make : Dlink, Ubiquiti, Cisco (f) Adaptor Panel (i) 6 port adaptor Panel for SC Adaptors Make : Dlink, Ubiquiti, Cisco (g) SC-SM-Simplex Pigtail of suitable length (i) Insertion Loss <=0.2 db, max 0.3 db (ii) Return Loss PC>=45dB, UPC>=50dB, APC>=60dB (iii) Connector Ferrule Ceramic (iv) Apex Offset <50um (v) Fiber Height +-100nm (vi) End Face Radius of Curvature 7mm<R<25mm (vii) Repeatability <=0.2 dB 1,000 times mating cycles (viii) Working Temp -40deg C to +85 deg C Make : Dlink, Ubiquiti, Cisco (h) CAT6 UTP 24 AWG Patch Cord of suitable length, Plug 30U snag less Make : Dlink, Finolex

Seamless Integration of the above PLC Panels into the Existing SCADA System incorporating (a) Development: (i) SCADA Screens for new Updated Panel configuration (ii) Layout for App new Updated Panel configuration (iii) Report Format new Updated Panel configuration (b) On-site development: (i) Modifications in SCADA Screens (ii) Modifications in reporting format (iii) Modifications in App layout

The quoted cost shall deem to be included the cost of communication for 12 months from the date of completion. Above All automation panel should connected to existing SCADA server and any other leftout devices and accessories require to commissioning should be consider and same should be include in quoted rates and department will not pay extra cost for the same. Make of Control Panel: Cimcon Software Pvt Ltd/ Reckronic Devices and Systems / Sombansi Schneider/Universal Switchgear. Note :- Cost for Synchronising of panel in to existing SCADA system is in contractors scope only and no extra payment shall be given to the contractor by the department.

Material and labour for attending the water supply breakdowns of any size/type of pipes in any position/location/depth including necessary excavation and earth work in any type of soil, cutting of pipes, welding, replacement of pipes of any nature, flanges, bends, collars, nut bolts, gasket, run lead joint or any other items required for rectification of break downs, testing and making good to the disturbed surfaces after rectification complete all as specified and directed by the Engr-in-charge for the following size of pipe lines :-

300/250 mm bore CI/DI/MS pipe line

200/150 mm bore CI/DI/MS pipe line

100/80/50/40 mm bore CI/DI/MS/GI pipe line

Note :- (a). Items like CI/DI/MS/GI fittings and pipes shall be measured and paid separately under relevant item of schedule 'A'. (b). Remaining items shall be deemed to be included in the rate quoted and no extra payment shall be paid for the completion of break down. (c) After hand over of complaint, contractor shall complete the break down within 24 hrs otherwise panel recovery shall be made for Rs.2500/- per breakdown.

Supply and fixing in repairs PVC water storage Tank with cover two layer, ISI marked, pure anti microbial round type including replacement of new GI fittings i.e. tank nipple, washers, float valves and Gate valves and Pipes for connecting the existing delivery lines hoisted and fixed in position all as specified in SSR Part-I and directed by the Engr-in-charge for the following capacity :- Note :- Gate valves and GI pipe only shall be paid under relevant item of Schedule 'A' remaining items shall be deemed to be included in the quoted item rate.

5000 Litre capacity

3000 Litre capacity

2000 Litre capacity

1000 Litre Capacity

Supply and fixing in repair including Installation, Testing & Commissioning of Motor Actuated Butterfly Valve consisiting of Quarter turn single phase Actuator and Wafer type butterfly valve of size 50 mm dia with appropriate bracket/mounting arrangement including two nos. limit switches for open and closed condition and splash proof enclosure complete all as specified and directed by the Engr-in-charge with following Specifications & Features Input Voltage: 230 V, A.C. Designed line pressure: 10 kg/sq cm. Operating Angle: 90 degrees Disc Material: CI with nylon coating Limit Switches : 02 Nos.For open and close status Mounting : On existing pipe Make: EMTORK / HASEL HOFENER / RITETORK /SIEMENS/ HONEY WELL

Supply and laying in repairs spigot and socket ductile iron water tubing,class K-9, cement mortar lining on inner surface and one coat of bituminous paint over exposed surface ISI marked conforming to IS No. 8329: 2000, including rubber joint of suitable size laid on roof/floor/trenches with proper alignment as per site requirement and carrying out testing against leakage before filling the trenches complete all as specified and directed by the Engr-in-charge

300mm bore

200 mm bore

150 mm bore

100 mm bore

Supply and fixing in repairs for CI or DI specials conforming to IS - 1538 or 9523, spigot /socket or flanged fitting i.e. bend, tee, collar, flanged/ socket /spigot, Tappers, flanges and tail pieces etc suitable for 100/150/ 200/ 250/ 300 mm bore CI/DI pipes complete all as specified and directed by the Engr-in-charge Note - Joints and jointing material shall be measured and paid seperately.

Material and labour for run lead joint with pig lead including pumping out / bail out water and necessary excavation and earth work in any type of soil to repair the joints including taking out existing joint carefully from following sizes of pipes complete all as specified and directed by the Engr-in-charge :-

300 mm bore

200 mm bore

150 mm bore

100 mm bore

Material and labour for Cutting existing cast iron/DI pipes and reducing for insertion of CI/DI fittings to required length in position for following sizes complete all as specified and directed by the Engr-in-charge :- Note :- Pipe fittings used shall be measured and paid under relevant items of schedule 'A' remaining items like welding and other items required shall be deemed to be included in the quoted item rate

300 mm bore

200 mm bore

150 mm bore

100 mm bore

Supply and fixing in repairs MS pipe heavy grade for suction and delivery for pump including necessary fitting welding, painting with 2 coats of synthetic enamel paint over a coat of red oxide zinc chrome primer and providing necessary PCC support as per existing for following size complete all as specfied and directed by Engineer-in-charge of following sizes :-

300 mm bore

200mm bore

150mm bore

100 mm bore

80 mm bore

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth and getting out in soft/loose soil complete all as specified and directed by the Engr-in-charge

Returning filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cms in any type of soil complete all as specified and directed by the Engr-in-charge

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15 cm thickness (below or above ground level) including removing debris out side MoD land complete all as specified and directed by the Engr-in-charge

Material and Labour for cement concrete 1:2:4, type B-2 (using 40 mm graded crushed stone aggregate) as in support of CI pipes, foundation and hardstanding including finishing surface even and fair including necessary formwork complete all as specified and directed by the Engr-in-charge

Removing excavated material exc 250 m but n.exc 500 m and depositing where directed complete all as specified and directed by the Engr-in-charge

Supply and fixing in repair mild steel Compound girders and stanchions, lattice girders, aerial masts,staging for water tanks and the like including caps, bases, ladders, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars,stiffeners, gusset plates, nuts, bolts, washers etc. including necessary fabrication work with hinges, handle and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified and directed by the Engr-in-charge.

Repair/Routine maintenance including carrying out daily check of fire alarm/fire fighting system complete with electronic control panel in the following buildings including personnel to attend the fire alarm system faults, testing, checking and replacement of unserviceable minor components ie nuts, bolts, washers etc other than mentioned in schedule here-in after and fire alarm system consisting the following complete all as specified and directed by the Engr-in-charge :- (a) Indicator (b) Electronic hooter (c) Manual call point (d) Smoke detector (e) Heat detector (f) Electronic fire control panel (g) Main/Zone cards (h) Battery of Fire panel DC supply (j) All wiring and cable connections (k) Control/Monitor module Details of buildings are as under :- (i) Dhanush, Vrishabh, Tula, Makar, Mesh, "G" block, 'H' block, Kumbh (G+14 floors) (ii) Jyesta & Dhanista (G+15 floors) (iii) G block, F1 block, AQ block, AR Block and 200 Sailors accn (G+6 floors) (iv) Asha 2 to Asha 5 (G+5 floors) (v) R-41 & R-42 bldgs (G+21 floors) and (vi) SHO building (G+2 floor) Note :- 1. Contractor shall also to provide adequate skilled manpower for testing of fire fighting system of buildings as per schedule to be issued by the user section. The cost of testing shall be deemed to be included in the quoted item rate. 2. Minor Items like fuses, loop cards, detectors circuits are required at site to make functional are included in the quoted item rate. 3. One Technician and one helper shall report daily to JE E/M regarding maintenance of work at site and quoted rate shall include the same.

Supply and fixing in repairs including installation, testing & commissioning of micro processor based 2 wire fault tolerant loop, required loop net workable type 2 loop (each loop accessing maximum 99 detectors and 99 modules) fire alarm/detection control panel. The panel shall be able to give location of all fire/fault signal with address. The panel shall have rectifier, loop cards, 80 character LCD unit to indicate Fire/Fault signal with address. The panel shall have a built in power supply and battery charger alongwith maintenance free 7.2 AH, 2x12 volt SMF lead acid batteries capable of running for a minimum of 48 hours with battery charger complete as required and as per specifications duly approved by EN 54 complete including of all 15 Amp power point connection from meter room to fire control panel complete all as specified and directed by Engr-in-Charge. Make :- Morley IAS by Honey well model No DXC2/714-001-225 or Bosch Model No FPA-1000-V2 of Schneider Cat No FFSULH 1002 model No ESM Ultima.

Supply & fixing in repair detectors Complying with and type certified to EN - 45 Addressable type multisensor detector with heat and smoke combination Photoelectric /Optical with base with self built intelligence as per IS: 11360 complete all as specified and directed. Make :- Bosch/Morley/Appollo/GST/Agni/Ravel/Schneider Note :- Loop cards, circuits as required to make functional is deemed to be included in the item rate and no extra shall be paid to the contractor.

Supply & fixing in repair Maintenance free battery duly charged 12 V 7.2 AH, ISI marked complete all as specified and directed by the Engr-in-charge

Supply and fixing in repair Addressable manual call point resettable type complete all as specified and directed by the Engr-in-charge Make :- Bosch/Morley/Appollo/GST/Agni/Ravel/Schneider

Supply and fixing in repair Addressable sounder with strobe complete all as specified and directed Make :- Bosch/Morley/Appollo/GST/Agni/Ravel/Schneider

Material and Labour for carefully opening existing unserviceable electronic sounder cum strobe with manual call point including soldering of circuits, cleaning, replacement of glass and painting as per existing and making serviceable and testing complete all as specified and directed by the Engr-in-charge

Supply and fixing in repair PVC insulated PVC sheathed armoured copper conductor cable of size 4Core x 1.5 Sqmm fixing on walls with saddles complete all as specified and directed by the Engr-in-charge

Supply and fixing in repair PVC insulated PVC sheathed armoured copper conductor cable of size 2 Core x 1.5 Sqmm fixing on walls with saddles complete all as specified and directed by the Engr-in-charge

Material and labour for factory fabricated Hose box made of 18 gauge MS Sheet 800mm X 600mm X 250mm with double door with 4 mm thick glasses and door frame made of 16 gauge MS sheet painted fire red out side and brilliant white inside yard fixed on wall with necessary nuts/bolts or welding to existing MS pipe by supporting angle complete all as specified and directed by the Engr-in-charge

Supply & fixing in repair rubber hose pipe 30 mtr,20mm dia plain 2 ply rayon confirming IS-12585 braided high pressure complete all as specified and directed by the Engr-in-charge. Make:-Minimax / Safex /DUNLOP

Supply & fixing in repair canvas fire hose 63mm bore 15 m long confirming to IS 636-1988 having male/ female brass coupling both end complete all as specified and directed by the Engr-in-charge. Make:-Minimax/Safex/DUNLOP

Supply & fixing in repair Gun metal Nozzle 15 mm bore, ISI marked suitable for 63mm dia canvas pipe complete all as specified and directed by the Engr-in-charge Make:-Minimax/Safex/DUNLOP

Supply & fixing in repair hose Reel drum suitable for and including 30 mtrs X 20 mm dia rubber hose pipe confirming to IS-884 complete all as specified and directed by the Engr-in-charge Make:-Minimax/Safex/DUNLOP / Jyothi

Supply & fixing in repair 100 mm bore ERW MS pipe heavy grade including MS fittings confirming IS-1239 and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer to pipe including welding, supporting brackets as required at site complete all as specified and directed by the Engr-in-charge Make:- Jindal /Tata /Zenith/BST/Sail

Supply & fixing in repair gun metal Two way fire brigade inlet , ISI marked conection with adaptor of size 80 mm dia X 63 mm dia , ISI marked complete all as specified and directed by the Engr-in-charge. Make :- Minimax / Safex / DUNLOP

Supply & fixing in repairs Branch pipe gun metal 63mm, ISI marked, instantaneous inlet, made threaded outlet, 15mm bore nozzle , ISI Marked complete all as specified and directed by the Engr-in-charge Make :- Minimax / Safex / DUNLOP

Supply & fixing in repair double headed outlet hydrant valve 100mm having 65mm outlet with lock pin wheel , ISI Marked complete all as specified and directed by the Engr-in-charge Make:-Minimax/Safex/DUNLOP

Supply & fixing in repair single headed outlet hydrant valve 100mm, ISI marked, having 65mm outlet with lock pin wheel complete all as specified and directed by the Engr-in-charge Make:-Minimax/Safex/DUNLOP

Supply & fixing in repair sluice valve 150mm size both ends flanged with high tensile stainless steel spindle, CI body as per IS-14846, ISI Marked,PN-1.6 including all joints with rubber or fibre board, nuts, bolts, washers complete all as specified and directed by the Engr-in-charge

Supply & fixing in repair sluice valve 100mm size both ends flanged with high tensile stainless steel spindle, CI body as per IS-14846, ISI Marked,PN-1.6 including all joints with rubber or fibre board, nuts, bolts, washers complete all as specified and directed by the Engr-in-charge

Supply & fixing in repair Non return valve 100mm size, ISI marked, both ends flanged with high tensile stainless steel spindle, CI body including all joints with rubber or fibre board, nuts, bolts, washers complete all as specified and directed by the Engr-in-charge

Supply and fixing in repair Foot valve 150 mm dia ball type10/15Kg/sqcm (MODEL B-5) of (ISI marked) in position at location including M&L for making flanged joints and making good to existing PCC surface complete all as specified and directed by the Engr-in-charge

Material and labour for Disconnecting carefully motor from pump of any Make, model and remove Bearing using bearing puller gear and fix new bearings at DE /NDE including necessary greasing ,check for proper shaft alignments such that no vibratiobn produce during opertion of following capacity Motors complete all as specified and directed by the Engr-in-charge.

Pump coupled with 60 HP motor (Bearing size 6312 ZZ & 6311ZZ)

Pump coupled with up to 15 HP motor (Bearing size 6307 ZZ & 6309ZZ)

Supply and fixing self lubricated asbestoes non metallic and non graphite gland packing of sizes 8 to 12 mm complete all as specified and directed by the Engr-in-charge Make : Champion or techno and commercial as approved by GE

Material and labour for scrapping of paint from pump, motor, base frame and accessories complete and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer , motor capacity 15 HP to 75 HP complete all as specified and directed by the Engr-in-charge

Supply and fixing in repair mild steel work in frames, ladders, tank stagings of size and thickness as per existing on site including nut, bolts, washers,welding and fabrication and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed by the Engr-in-charge

Supply and fixing in repair rubber vibration pads heavy duty for base frame as per sample suitable for the following size of pumpsets complete all as specified and directed by the Engr-in-charge :-

Supply and laying in repairs PVC insulated unarmoured power cable copper conductor, 1100 Volts grade, conforming to IS 7098 (Part 1) 1988 of sizes given below laid through and including HDPE pipe of suitable size fixing on walls with saddles complete all as specified and directed by the Engr-in-charge:-

35 Sqmm Single core

25 Sqmm Single core

16 Sqmm Single core

Material and labour for disconnecting motor power cables of various sizes from electrical motor of different capacities and decoupling from the pump sets,removing and taking down carefully and transporting to authorised workshop ,Dismantaling startor and rotor carefully and rewinding stator assembly with supper enamelled copper winding wire of suitable gauge matching to existing gauge and cleaning of slots ,core with carbon tetra chloride solution and applying two coats of insulation varnish and keeping stator assembly in heating chamber to improve insulation strength ,reassemble motor completey and transporation to site ,coupling pump to motor and check for proper shaft alignments such that no vibration is produced during operation coupling to pump with exact alignment ,connecting power cables to motor and testing of following capacity motor complete all as specified and directed by the Engr-in-charge

up to 15 HP

Supply and fixing in repair fully automatic Star delta starter pre-wired with Sheet metal enclosure company made, suitable for 75 HP/55 KW Pump set having contactors, relays, timers of suitable size, relay range 45-75 Amp complete all as specified and directed by the Engr-in-charge Make :- L&T Cat No.SS94022 or equivalent make given in Appx 'B'

Supply and fixing in repair fully automatic Star delta starter with Sheet metal enclosure company made, suitable for 17.5 HP/13 KW Pump set having contactors, relays, timers of suitable size, relay range 09-15 Amp complete all as specified and directed by the Engr-in-charge. Make :- L&T Cat No.SS94362 or equivalent make given in Appx 'B'

Material and labour for preparing surfaces by rubbing with emery papers for removing of rust from fire fighting Pipe lines , fittings, motors, pumps, cabinet boxes, valve chamber covers, fire brigades and other items relating to complete fire fighting system in buildings up to (G+21 floors), cleaning and applying two coats of red colour synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed by the Engr-in-charge

Shetty Construction Co