PROVN OF DRAINAGE SYSTEM, UPGRADATION OF TRANSFORMER AND SPL REPAIR TO BLDG NO. T-02 UNDER GE SATWARI

Amount

Dismantiling of Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantiling of Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet in roof coverings.

Dismaniting of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete.

Dismantling timber scantlings in fillets, rails, posts, rafters, purlinss, etc, under 40 Sq. cm in section, in any position in framed work.

Dismantling timber scantlings 40 Sq. cm and over in section, in any position in framed work.

Dismantling boarding, any description, fixed in any position with nails.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off premises.

Demolition of brick work built in CM complete all as specified and directed.

M&L for surface excavation n.exc. (Not exceedings) 30 cm deep and averaging 15 cm deep and getting out in any type of soil.

Excavation in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes,cables,pipe line,pole etc. not exceeding 10 Sqm on plan and not exceeding 1.5 mtr in depth and getting out, in any type of soil, complete all as specified and as directed by Engineer-In-Charge.

Description all as item no 11 but exceeding 1.5 mtr and not exceeding 3 mtr depth.complete all as sepecified dirceted by engr-in-charge.

Returning Filling in,including spreading, levelling, watering and well ramming in layers, not exc 25 cm in soft/loose soil complete all as specified and as directed.

Removing excavated material n exc 50 m and depositing where directed at level n exc 1.5m above the starting point complete all as specified and as directed.

Taking down cement plaster of any description on brick work and removing all the demolished material outside cantt area.

Taking down chowkhats or frames with shutter (without taking off shutters from the frame) not exceeding 1.5 sqm each and removing from site complete all as specified.

Taking down chowkhats or frames with shutter (without taking off shutters from the frame) exceeding 1.5 sqm but not exceeding 4 sqm each and removing from site complete all as specified.

Taking down Existing false ceiling board with frame grid and refixing in same position complete all as specified and directed by Engr-in-charge.

Brickwork with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:6.

Brickwork with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:4.

M&L for brick work with subclass 'B' bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:4 complete all as specified and as directed by Engineer-in-charge

Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4.

M&L for extra for forming fair finished drain or drain channel 60 cm inner girth in cement concrete using extra cement including forms moulds mitred stopped ends etc complete all as specified and as directed.

M&L rendering 10mm thick in CM 1:4 on concrete surfacves/ chajja/ ceiling, etc finished even and smooth without using extra cement complete all as specified and as directed.

M&L 25mm thick PCC 1:2:4 type B1 (20mm graded stone aggregate) as in floor and finished rough to recive the floor tiles etc complete all as specified and as directed.

M/L for cement concrete 1:3:6 Type C-2 using 40mm graded crushed stone aggregate to the bed of drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150mm bore complete as all specified and directed by Engineer-in-Charge.

M/L for cement concrete 1:3:6 Type C-2 using 40mm graded crushed stone aggregate to the bed of drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 600 mm bore complete as all specified and directed by Engineer-in-Charge.

Material and labour for rendering 15 m thick on fair faces of brick or concrete surface walls, in cement mortar 1:4 , rendering is to be finished even and smooth without using extra cement complete all as specified.

Material and labour rendering 15 m thick on fair faces of brick or concrete surface walls, in cement mortar 1:6 , rendering is to be finished even and smooth without using extra cement complete all as specifeid.

Material and labour for preparation of new plastered surfaces of walls & applying two coats of oil bound distemper over two coat of wall care putty of 1 to 2 mm thick and one coat of primer complete all as specified.

Preparation of new plastered/ concrete surfaces of walls to achieve smooth and even surface and applying two coats of cement paint over and including one coat of white wash complete all as specified and directed.

Material and labour for preparation of old plastered surfaces of walls & applying two coats of oil bound distemper complete all as specified.

M&L RCC type B1, 1:2:4 (20mm graded aggregate) as in slab supported on walls, beams and columns in floors , roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M/L for PCC (1:4:8) type D-2 using 40mm graded crushed stone aggregate as in foundation filling and mass concrete complete all as specified.

M/L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in stay assy, filling and mass concrete complete all as specified.

M/L for PCC (1:2:4) type B-1 using 20mm graded crushed stone aggregate as in pole pedestal,benching, water troughs and the like including slightly rounded chamfered angle and throughting etc all as specified and directed by Engineer-in-Charge.

M&L Pre-cast PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in manhole cover slab set in CM 1:4 complete all as specified.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1: 2: 4 type B-1 smooth finished, and reforming benching as required

M&L Form work to sides and soffits of floor or roof beams , beam haunchings, girders, bressummers, lintels, cantilevers,shelves including supports, overhangs, etc also splays between floors and beams, etc for rough finished flat surfaces of concrete complete all as specified and as directed.

M&L Form work to soffits of suspended slabs such as roof slabs, floor slabs,landings and similar works : not exceeding 200mm thick (horizontal or sloping) for flat rough finished surfaces of concrete complete all as specified and as directed.

M&L Form work to edges of concrete flats, treads,breaks in floors, window cills, concrete railing, openings in concrete walls, floors and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls,horizontal or sloping and similar work exc 10cm but n exc 20 cm wide for rough finished surfaces of concrete complete all as specified and as directed.

Mild steel Framed work as in door or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Dorrs etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging dooe fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete of Gde Fe 410-O or Fe 310-O.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Refixing of Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Supply and fixing GI snap grid frame work (Grid size 605cm x 605cm) for false ceiling consisting of main runner 'T' of size 24mm x 32mm and 0.3mm thick , Secondary runner 'T' of size 24mmx25mm and 0.3mm thick,GI angle 24mmx24mm and 0.4mm thick,Bottom exposed capping of width 24 mm of all T-sections shall be of 0.25mm thick PPGI, hot dipped galvanised steel with zink coating not less than 120gm / Sqm, ceiling grid system duly suspended by 4mm dia GI wire hanging from existing purlins /roof slab with butterfly clips including Gypsum ceiling tiles of size 595 x 595 x 9 mm laminated with 0.07 mm thick polyvinyl film on the face side and 10 micron metalized polyester film on the back side fixed on GI snap grid including taking down of old us material complete all as specified and directed by Engr-in- Charge.

Material and labour Non - skid Digital Ceramic jointless coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface over 15 mm thick screed bed in CM 1:4. Make Somany, Kajaria , Varmora (Sample as approved & Kept in GE's sample room)

Material and labour Non - skid Digital Ceramic jointless coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface over 15 mm thick screed bed in CM 1:4. Make Somany, Kajaria , Varmora (Sample as approved & Kept in GE's sample room)

Material and labour glazed ceramic coloured Digital tiles in vertical surface 300x450x7 mm thick, set and jointed in neat cement slurry and pointed white or colored cement to match the surface over 10 mm thick CM 1:4 all as specified. Make Somany, Kajaria, Varmora (Sample as approved & Kept in GE's sample room)

Material and labour Vitrified Ceramic(Double Charged) edge cut joint free coloured or printed any shade tiles 10 mm thick (square/ rectangular) polished area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match over 15 mm thick screed bed in CM 1:4. Make Somany, Kajaria, Varmora (Sample as approved & Kept in GE's sample room)

Description all as item no 50 but as in vertical surfaces dado/skirting over a backing coat of CM 1:4, 10 mm thick complete.

S&F 100mm long butt hinges extruded alumn alloy with galvanised mild steel hinge pin, anodized and fixed complete all specified.

S&F extrude aluminium alloy handles, fabricated type, anodized size of 125 mm long complete.

S/F for Al anodised barrel tower bolts of extruded section and fixed of size 150mm complete.

S&F for solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete.

S/F for Solid factory made solid panel PVC door shutter 30 mm thi.k (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width shirk inside with solvent cement for stiles and plan colour PVC sheets for top rail, lock rai & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F in repair Vitreous China, wash basin white, flat back , size 550mmx400 including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32 mm dia, waste coupling of chromium plated brass. complete all as specified and as directed by Engineer-in-charge.. Make :- Cera, Cat No- S2040119 or equivalent in Jaquar/ kohlar/essco.

S&F in repair full pedestal for WHB complete all as specified. Make :- Cera, Cat No- S2090113 or equivalent in Jaquar/ kohlar/essco.

S&F in repair Wall Hung twin flush Cistern with Drainage L-Bend Pipe with Gasket & Installation Kit (Suitable for EWC), complete all as specified. Make:- Cera, Cat No- B1020106 or equivalent in Jaquar/ Kohler/ Artize.

Supply and fixing in repair Vitreous china ware pedestal type water closet white, with 'P' or 'S' trap including self closing seat cover, closed pattern with flat bottom,complete all as directed. Make:- Cera, Cat Part No- S1051103 or equivalent in Jaquar/ Hindware.

S&F in repair for Tubular towel rail, 20mm dia D type 60cm long between flanges of brass chromium plated complete all as specified.

S&F in repair CP Bib taps, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified complete all as specified.

S&F in repair CP Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified.

Supply and fixing CP brass stop cock/angle valve 15mm dia fancy type chromium plated with long sank and cup concealed type complete all as specified.

Material & labour factory made steel windows double shutter box type, outer frame made out of ERW TUBE 'P' section(65x45x25mm) and shutters of ERW TUBE 'P' section (50x35x20mm) operable shutters side hung including pistol hinges with two Nos of MS Tower bolts 150mm size on each shutter steel handle and stopper of 'Z' section as specified complete with sash bars dovetailed or welded ready for glass fixing and wire gauzed fixing with suitable fittings/opening for cooler/AC where required .Steel windows will be double shutter external glazed and internal wire gauzed complete all as specified and as per Drg No CEPZ/TD-324/07 1/3 to 3/3 all as specified and directed by Engr-in-Charge. NOTE: The quoted rate against the above item shall also include (i) for Provn of one coat of coal tar on the ends of steel frame in contact with brick/conc surface (ii) 04 Nos MS Steel lugs of 20x5mm MS flat 20cm long over all welded to frames (iii) PCC block for embedding lugs.

Material & labour for framed work such as grills grating etc with ends of bars shouldered and /or riveted , or forged into spike; framed guard bars, barred iron doors, leaders, framed balusters, walk ways, railings framework of water tanks and similar work conforming to Fe 290 Gde-E-165

Supply and fixing stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm complete all as specified fixed with stainless steel wire staples.

Supply and fixing Sheet glass ordinary quality 3mm thick and glazed with oil putty or any types of beads in square n.exc 0.5 Sqm each pane in any type of frame of Iron/ Steel/ Wood/ Aluminium as required at site complete all as specified.

Supply and fixing Sheet glass ordinary quality 5.5mm thick and in square n.exc 0.5 Sqm each pane in any type of frame of Iron/ Steel/ Wood/ Aluminium as required at site complete all as specified.

M&L preparation of new steel surface exc 10cm width or girth and applying two coats of synthetic enamel paints over one coat of red oxide primer all as specified.

Material and labour for repairing of concrete surfaces such as chajjas,upward facia,downward facias,ceiling and similar items with plain cement concret 1:2:4 type B-0 or rendering 10mm thick in CM 1:3 includind dubbing coat without using extra cement finished even and fair including necessory formwork and scaffolding complete all as specified and directed.(Up to fourth storey bldg and no extra payment will be paid for formwork and scaffolding)

M&L formwork to soffit of suspended slab such as roof slab, floor slab etc.

M&L MS TMT bars 10 mm and above , cut to length, bent to shape required , including cranking , bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in reinforcement.

Description all as item no 73 but 6 mm to 8 mm dia complete all as specified and as directed.

M&L for providing, cement concrete type B1 1:2:4 (12.5mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed.

M&L for 50 mm thick PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement,laid in bays and including filling of joints with bitumen mastic comprising one part of bitumen 85/25 mixed with three parts of coarse sand by weight complete all as directed.

M&L for 75mm thick PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement,laid in bays and including filling of joints with bitumen mastic comprising one part of bitumen 85/25 mixed with three parts of coarse sand by weight complete all as directed.

Supply and fixing in repair double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty.

M&L for PCC 1:4:8 type D-2 ( 40 mm graded aggregate) as in sub base , 75 mm thickness.

Material and labour for precast factory made designer tiles (Rectified interlocking tiles)300x300mm glazed top made in white cement and pigment base of thickness not less than 19mm in different colour and pattern (compressive strength not less than 250 kg/sqcm) set and jointed in neat cement slurry (colour and pattern as per sample kept in GE office as approved by GE) including 20mm thick screed bed in CM 1:4 all as specified and directed by Engr-in-Charge.

S&F Factory made mild steel box type ventilator with side hung shutters including pintal hinges with 2 nos MS tower bolts of 150 mm size on each shutter , steel handle and stopper of Z section with sash bars dovetailed or welded ready for glass fixing, without guard bars/grills complete all as specified and shown in Drg No CEPZ/TD-325/07 dt 04-12-07 and CEPZ-TD-324/07 dt 4-12-07

S&F Mild steel framed works such as grills, framed guard bars, etc and similar work conforming to Fe 290 Gde E-165, barred iron door,purlin rafter etc complete all as specified and as directed.

S&F 3mm thick sheet glass, ordinary quality glazing with oil putty in square n exc 0.50 sqm in each pane complete all as specified and as directed.

Supply and fixing tubes 'medium grade' galvanised, 15 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing tubes 'medium grade' galvanised, 20 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge.

S&F Pillar cock long neck with aerator 15mm dia cast copper alloy fancy type complete all as specified.Make:- Essco, Cat No-SQT-508KN or equivalent in kohler/ Jaquar.

S&F 110 mm dia PVC (SWR) type 'B' pipes single socketed in any length with rubber ring joints using solvent adhesives fixed to walls with brackets etc complete all as specified and as directed. Make -Astral,Supreme, Finolex

S&F 75 mm PVC (SWR) type 'B' pipes single socketed in any length with rubber ring joints using solvent adhesives fixed to walls with brackets etc complete all as specified and as directed. Make -Astral,Supreme, Finolex

S&F PVC (SWR) type B bends any radius provided with access door of 75 mm dia complete all as specified and as directed. Make -Astral,Supreme, Finolex

S&F PVC (SWR) type B vent cowl of 75mm dia complete all as specified and as directed. Make -Astral,Supreme, Finolex

S&F 75 mm bore PVC (SWR) type B floor trap,plain with grating including jointing to waste pipe, all as specified. Make -Astral,Supreme, Finolex

S&F Urinal (CAPRIANA in white colour, ) half stall with complete accessories Set, CP Waste Coupling, PVC waste pipe, sprader etc. Size: 375 x 390 x 590 mm complete all as specified. Make:- Cera, Cat No- S4020112 or equivalent in Jaquar/ kohlar/essco.

M&L Preparation of new plastered surfaces of wall and applying two coats of cement based paint complete all as specified and as directed.

M&L Preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified amd as directed.

M&L for Preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

Supply and fixing Rotational moulded polyethylene water storage tanks of 500 litres capacity,(cylindrical vertical with closed top) triple layered, white, hoisted and fixed in position all as specified in SSR Part-I including ball brass valves, high pressure with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe, including making connections complete all as specified

Supply and fixing Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe of 20 mm bore pipe including making connections complete all as as specified and fixed (Minimum weight 20mm-210 gms).

S&F WC Orissa pattern white with integral foot rest 580x 440 mm including L bend, & PCC bedding in 1:2:4 and making good disturbed floor connecting to trap and flush pipe compete all as specified.(Rate of including in taking out and removal of old WC seat unhygienic condition) Make:- Cera, Cat Part No-S3010109 (COVYNA) or equivalent in Jaquar/ kohlar/essco.

S&F PVC valveless,syphonic action type, flushing cistern, low level,white with inlet, ball valve, float and handle including brackets, PVC 32 mm 'L' bend of capacity 10.0 litres and making good to dismantled/damaged floor/surfaces,complete all as specified and as directed by Engineer-in-charge. Make:- Cera, Cat No- B1010107 ( CABRINA) or equivalent in Jaquar/ kohlar/essco.

S&F stop cocks, cast copper alloy, chromium plated with long shank and cup (concealed type), high pressure with capstan head handle, screwed both ends for iron pipe or for unions of 15 mm dia complete all as specified and as directed.

S&F angle valve with wall flange , cast copper alloy, chromium plated fancy type screwed for 15 mm iron pipe, complete all as specified.

S&F Bib Cock with nozzle, cast copper alloy, chromium plated fancy type Quarter turn fix with iron pipe, 15 mm bore complete all as specified. Make :-Essco, Cat No:-SQT-512KN or equivalent in kohler/ Artize/ Jaquar.

S&FOverhead Shower 80 mm dia Round Shape Single Flow (ABS Body Chrome Plated with Gray Face Plate) with Rubit Cleaning System including shower arm 240 mm long (Light Weight) Round Shape for Wall Mounted Showers with Wall Flange complete. ( For Shower Make:- Essco, Cat No-EOS-541RB.) & ( For Shower Arm Make :- Essco, Cat No- ALE- 536A) or equivalent in kohler/ Artize/ Jaquar/cera.

M/L for salt glazed stone warer drain pipe laid in trenches and jointed in cement mortar 1:2 for 150mm bore of pipe grade 'A' complete as all specified.

M&L for 600 mm dia reinforced concrete pipes, class NP2 , laid and jointed complete with collars complete all as specified and as directed.

Material and labour for cutting of existing GI pipe/CI pipe off size 200/150/100mm bore for insertion of Tee, coller for taking branch connection of suitable size of bore including threading all as required at site.

Supplying, laying, jointing & testing galvanised steel tubing 50 mm bore medium grade with screwed joint together with all fitting such as bends, elbows,tees,short pieces and union etc laid in trenches including taking out old unserviceable,cracked steel tubing including all fittings complete all as specified and directed.

Supplying, laying, jointing & testing galvanised steel tubing 40mm bore medium grade with screwed joint together with all fitting such as bends, elbows, tees, short pieces and union etc to wall, ceiling, floor complete all as specified and directed. Note:- Earth work shall be measured and paid separately under respective item of shedule 'A'.

Supply and fix Valve, globe conforming to IS 9338, 40 mm dia pipe complete all as specified and directed Make - Prakash Surya/TATA/Jindal

Supply and fix Valve, globe conforming to IS 9338, 50 mm dia pipe complete all as specified and directed Make - Prakash Surya/TATA/Jindal

Material and labour for construction of one brick masonary valve pit built in cement mortar 1:6 of size 60cm x 60cm x 60cm (internal dimension) over 15cm thick PCC 1:3:6 type C-2 sub base extended alround 15cm beyond external edge of brick work including plastering 15mm thick in cement mortar 1:4 internally and plus pointing to brick wall surfaces externally as work proceeds complete with MS sheet cover 3.15 mm thick with handle and locking arrangement, angle iron frame (grouting with anchor fashioners length not less than 15cm - 04 Nos) and painting with a coat of synthatic enamel paint over a coat of red oxide, complete all as specified and directed.

Material and labour for road cutting by using drilling machine and repair the road by using plain cement concrete 1:3:6 (40mm graded aggregate) type C-2 with necessary form work alongwith demolition of old PCC all as specified and directed.

Taking down carefully aluminium conductor point wiring (light, fan, light socket, power socket) complete fitting such as swithes, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and as directed.

Taking down of unsv MCB DB SPN along with MCB's

M&L for complete point wiring for One light/fan point controlled by one, one way switch 6 Amp complete with 1.5 Sqmm single core multi stranded copper conductor FRLSH insulated and unsheathed heavy duty cable in colour code including continuous earth wire with cable of size 1.5 sqmm copper conductor flexible FRLSH insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked after cutting chases in wall , plastering after concealing conduit and making good to disturbed surfaces should be matched with existing colour of white wash , terminated into modular galvanised suitable size sunken boxes including white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc complete all as specified and as directed for the following :-

Description all as item no 117 but One 3 pin socket outlet 6 amp independent

Description all as item no 117 but One 3 pin socket outlet 6 amp same board

Description all as item no 117 but One bell/ buzzer point controlled by one, complete all as specified and directed.

Description all as item no 117 but for one 3 pin socket outlet 16 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire.

Description all as item no 117 but for one AC Plug in Socket independent with cable of size 4.0 Sqmm for point wiring and 4.0 sqmm as in continuous earth wire.

M&L modular type switch, one way 6 Amps , 1 module complete all as specified and directed.

M&L modular type socket 5 pin, 6 Amps combined 2 module complete all as specified and directed.

M&L modular type switch, one way 16 Amps, 1 module complete all as specified and directed.

M&L modular type socket 5 pin, 6 A/16 Amps combined 2 module complete all as specified and directed.

M&L modular type fan regulator step down 120 Watt, 2 module complete all as specified and directed.

Supply and fix moudlar Bell push made of polycarbonate piano flush type 6 amps , 240 V

S & F musical door bell, AC 230 volt single phase.

Supply and fixing ceiling rose surface, backelite, three terminal, 240 volts complete all as specified and directed.

Supply and fixing LED tubelight fitting 18-20 W LED, 230V, Batten type complete in all respect . Cat part No DMLN1LT8-16 of Crompton or equivalent Wipro , Havells alongwith LED tubeRod with heat dissipation capability suitable for G-13 base tubelights base fluorescent T8/T12 luminaire , 20 watt LED wattage with colour temp of 5700 K 1800 lumens and with surge arrestor complete in all respect. Cat Part No LTT8-20 of Crompton or equivalent in Wipro , Havells . Note:- The LED batten and LED tube rod shall be of same make.

S & F complete energy saving new generation 10W LED IP65 bulk head luminary with opal diffuser complete all as specified and directed .make: Crompton Cat part LBHE-10-CDL ,or equivalent in Havells ,Wipro

S & F of lamp holder,PVC /Polycarbonate type with back plate for batten fitting .

S & F LED lamp suitable for B22 holder of capacity 10 Watt. Make: havells model ADORE Ball lamp cat part no LHLDERUEMD8X010 equivalent in crompton/ bajaj

S&F sheet metal enclosure for MCB's DBs single pole & neutral 240V AC with 200 Amp rated neutal bus bar suitable for 4 ways outgoing MCBs with IP - 42 protection complete all as specified & directed.

S&F E-lite LED 18 watt tube light fitting with tube rod including its connection with 2 core flexible copper conductor cable with suitable size complete with all accessories all as specified & directed.

S & F Decorative Edge Lite linear and compact LED fixture with in-built electronic driver, luminaires 9 watt LED 4000K mirror light with decorative grey ends caps, polycorbonate body and ribbed opal diffuser and connection with 2 core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F Distribution Board (SPN) double door 8 Way and should be IP 43 protected with Copper Bus bar,Earth Bar ,neutral Bar Door Earthing .Makes: IndoAsian Optipro Cat Part No 811807 or equivalent in Havells/ Seimens/C & S Electric

MCB SPN complete 40 Amp with rupturing capacity 10 KA 'C' series, complete all as specified and directed.

MCB single pole 63 Amp with rupturing capacity 10 KA 'C' series,ISI Marked complete all as specified and directed.Make:- IndoAsian Optipro or equivalent in Havells/ Seimens/C & S Electric

MCB single pole 6 to 32 Amp with rupturing capacity 10 KA 'C' series,ISI Marked complete all as specified and directed.Make:- IndoAsian Optipro or equivalent in Havells/ Seimens/C & S Electric

S&F sub main wiring with single core cable 2x 10 sq mm FRLSH insulated Unsheathed stranded copper conductor cable 1100 Volts grade in rigid PVC conduit (Concealed) medium grade alongwith 1x10 Sq mm FRLSH insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including chesing, cutting & making good to match with the existing surface complete all as specified and directed.

M&L for complete earthing with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironl including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube flor watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion.

Supply and fixing of PVC Exhaust fan 250mm Sweep complete incl taking down of the old unsv exhaust fan and depositing the same in MES Store Yard.

Supply and fixing exhaust fan heavy duty 300/305 mm sweep, 900 RPM, 240 volt, AC, with & including louvers, mounting ring, MS rag bolts, nuts, washers etc and connected from ceiling rose/ connector with & including suitable size flexible copper conductor PVC insulated sheathed cord, complete.

Supply and fixing AC single phase 240 Volts 50 HZ ,ceiling fan of size 1200mm Sweep incl taking down and depositing old UNSV ceiling fan in MES store complete in white colour with canopy with all accessories incl nuts,bolts,clamps etc. Make :- Havells Cat Part No ES-50 Premium ,Crompton Cat Part No Entrust 50 or equivalent in BAJAJ.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps rating complete all as specified and directed.Make:- IndoAsian /Havells/ Seimens/C & S Electric

S&F Distribution Board (VTPN MCCB 125A DB Double Door) IP-43 and IK-08 protected fitted with fully insulated copper busbars assembly,insulated neutral bar ,earth bar ,door earthing, Blanking plates double door suitable for 4 pole MCCB upto 125,16 KA as incommer and out going MCBs 4 ways complete all as specified and directed.Note:- Rate includes MCCB.(MCBs shall be measured and paid separately.) Make:- INDOASIAN OPTIPRO Cat Part No: 811888 or Equivalent in Havells/Crompton/Legrand

Supply,installed , testing and commissioning outdoor type,step down transformer 11000/433 volts (at no load) AC, 3 phase 50 Hz capacity 250 KVA, core type, double copper wound,oil immersed,naturally cooled,oil natural, Air natural (ONAN) with external cooling fins, delta connected on primary side (HV) star connected on secondary side (LV) in accordance with vector symbol, DYN 11 (vector group) with neutral brought out on secondary side (LV side) and having tapping at + 2.5% to +7.5% HV side to be changed by means of hand operated off load tap change gear. The maximum temperature rise should not exceed 45 degree celcius in oil and 55 degree celcius in HV.LV winding when measured by resistance method after continuous full load run on an ambient temp of 40 degree celcius. The transformer shall be IS:1180 Part-1:2014 (Level-II) and BEE Certified and shall comprise of the followings:- (a) 03 Nos porcelain bushing with arcing horn on HV side suitable for 11 KV complete withbushing,copper rods, nuts and washers. (b) One cable box on LT side ( Secondary side) consisting of four Nos porcelain bushing with copper rods, complete with nuts and washers, with two Nos cable gland suitable for reception/taking out of XLPE insulated heavy duty armoured cable including gland, joint and jointing materials complete. (c ) Oil conservator with filter type frain valve and oil level gauge. (d) De- hydrating breather with first fill dehydrating agent (silica gel). (e) Explosive vent. (f) Thermometer pocket on tank cover. (g) One Nos 100 mm dia, dial type thermometer , vapor pressure type, having range 0 - 120 degree celsius with metal guard having maximum perimeter reading temperature indicator with resisting device for transformer.

(h) Two earthing terminals on tank cover to facilitate fixing of 32 X 6 mm galvanised iron earth strip for earthing of neutral & body. (i) Rating plate and terminal making plate. (j) Oil level gauge. (k) Oil drain/ fillter valve. (l) Lifting lugs. (m) Oil filling hole with cap/plug with connecting plate complete. (n) Air release valve plug. (o) Four plain solid cast steel detachable rollers. (p) Extra bushing for neutral , outside the LT cable box for providing independent earthing for neutral. (q) First filling of new and unused transformer oil IS-35/93 (fourth revision) marked (Make - savita/Power Oil) filtered and tested up to 40 KV dielectric strength at 2.5 mm air gap between testing Note:- (i) Certificate of dielectric strength shall be submitted by the contractor after filling the oil.

Supply, laying and testing XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty earthed) with aluminium conductor, 11 KV, grade cross sectional area 95 Sqmm 3 Core laid in trenches/road crossing/on wall etc complete and all as specified directed by engr-in-charge.

Supply, laying for underground LT cable 1100 Volts grade heavy duty electric cable XLPE insulated & PVC outer sheathing with aluminium stranded conductor, Armoured confirming to IS-7098 Part-I (1988) with latest ammendments of size 240 sqmm 3.5 core

Supply, laying for underground LT cable 1100 Volts grade heavy duty electric cable XLPE insulated & PVC outer sheathing with aluminium stranded conductor, Armoured confirming to IS-7098 Part-I (1988) with latest ammendments of size 95 sqmm 3.5 core

Supply, laying for underground LT cable 1100 Volts grade heavy duty electric cable XLPE insulated & PVC outer sheathing with aluminium stranded conductor, Armoured confirming to IS-7098 Part-I (1988) with latest ammendments of size 50 sqmm 3.5 core

Supply, laying for underground LT cable 1100 Volts grade heavy duty electric cable XLPE insulated & PVC outer sheathing with aluminium stranded conductor, Armoured confirming to IS-7098 Part-I (1988) with latest ammendments of size 300 sqmm single core

M&L for providing dry river sand as in sand cushioning to under ground cable including punning down of sand inlayers as specified and as directed.

Supply and laying dry bricks over cable laid in trenches as mechanical protection to cable with width equal to the length of bricks with well burnt sub class 'B' bricks complete all as specified

Supply and fixing galvanized steel stay assembly complete with stay rod 20mm dia including stay strand 7/4 mm fixed for stay of poles including necessary MS clamp of 50x6mm flat iron nuts and bolts, loop insulators complete all as specified and directed by Engr-in-Charge. Note:- Earth work, PCC shall be measured and paid separately.

M & L cross arms bracing support clamps, back plate etc fabricated from structural steel section with bolts, nuts, washers,welding, bending cold or hot,drilling holes for bolts in any shape and size as directed or indicated and painted with one coat of red oxide and two coats of aluminium paints.complete all as sepecified directed by engr-in-charge.

S& F Anti climbing device, spikes type, fabricated out of MS bars (round, square or flat) including nuts, bolts, washers and welding in two halves made to shape to suit the cross section of the poles, spike welded to flat iron, including on primer coat, one under coat and two finishing coats of silver aluminium paint including preparation of surfaces..complete all as sepecified dirceted by engr-in-charge.

Supply & fixing danger notice plate 250 mm x 200 mm made of mild steel sheet 1.6mm thick & vitreous enamelled white on both sides and with letters, figures and conventional skull and bones in signal red colour and fixed with MS clamps, bolts and nuts of approved size for HT 11 KV as required.complete and all as specified directed by engr-in-charge.

Supply & Install,including of Air break, gang operated switch with 15 Nos insulators, outdoor type pole, mechanically operated, suitable for vertical operations, single break, provided with locking arrangement (including 50mm Godrej lock with two keys) mounted on and including steel frame and HT post type insulators copper alloy, high pressure, with operating mechanism having operating rod of 20 mm dia GI pipe (medium grade) operating from 1.2m above GL complete including drop out fuses conforming to IS-1318 of 1972, rated voltage 11 KV and for current rating 400 Amp all as specified.

Supply & Errecting truelly vertical position steel tubular swaged poles complete with CI base plate, finial taper plug bolts, nuts & screws 11.0 mtr long type 410 SP-55 conforming to IS 2713 (Part 1 to 3, 1980 including two coat of synthetic enamelled aluminium paint over a coat of primer. Five strips of 300mm thick alternate black and white paint of approved make should be provided on pole from the PCC bad complete all as specified and directed.

S&F Lightning arrestors (set of three), expulsion type, HT metal oxide surge arrestor polymeric type, complete with all fittings, transmission class rated voltage 125 KV contionous operating voltage at 8/20 impulse, 75 KV discharge capacity 65 Kilo amp suitable for 11000 volts complete all as specified and directed

S&F outdoor type cable end termination jointing kit heat shrinkable complete with all accessories and jointing materials suitable mounting on channel/angle iron with and incl cable pieces of suitable size length and line type vice for 3 core 95 Sqmm XLPE HT cable (kit shall be not older than 3 months from the date of manufacture) complete all as specified and directed

M&L For Earthing complete with galvanized steel earth plate electrode 60cm x60cmX6 mm thick buried directly in ground to a depth not less than 3 mtr below normal ground level with top edge of earth plate at a depth not less than 2.25 mtr below ground level, earth plate surrounded by 15 cm thick packed layer of charcoal, magnicium sulphate, common salt and connected with in and including GI strip of size 32x6mm by means of stainless steel bolts, nuts, check nuts and washers connected to Transformers / panels. 40mm bore of GI pipe (light grade) from earth plate up to testing point for protection of GI strip and 20 mm bore GI pipe (medium grade) with wire mesh and funnel for watering including necessary excavation and earth work, (in any type of soil) PCC chamber (1:3:6) type C-2 with RCC cover with suitable size of handle made out of 8mm dia MS bars and angle iron 40 x 40x 3mm frame for cover complete all as shown in electrical plate No 3 of MES schedule Part I of SSR Part-I 2009 complete all as specified. RCC cover shall be painted with red paint over a primer coat and the rate include in the unit rate of item.

M&L For Earthing complete with galvanized steel earth plate electrode 60 cm x60cmX6 mm thick buried directly in ground to a depth not less than 3 mtr below normal ground level with top edge of earth plate at a depth not less than 2.25 mtr below ground level, earth plate surrounded by 15 cm thick packed layer of charcoal, magnicium sulphate, common salt and connected with in and including GI wire of 4mm dia by means of stainless steel bolts, nuts, check nuts and washers connected to Transformers / panels. 40mm bore of GI pipe (light grade) from earth plate up to testing point for protection of GI strip and 20 mm bore GI pipe (medium grade) with wire mesh and funnel for watering including necessary excavation and earth work, (in any type of soil) PCC chamber (1:3:6) type C-2 with RCC cover with suitable size of handle made out of 8mm dia MS bars and angle iron 40 x 40x 3mm frame for cover complete all as shown in electrical plate No 3 of MES schedule Part I of SSR Part-I 2009 complete all as specified. RCC cover shall be painted with red paint over a primer coat and the rate include in the unit rate of item.

Supply, installation, testing & commissioning of totally enclosed feeder pillar outdoor type fabricated out of 3.15 mm thick CRCA sheet dust and vermin proof powder coated double door type (independent cabin including locking arrangement for each MCCBs, bus bar chamber enclosed complete suitable for operating on 415 Volt 50 Hz AC supply internally wired with copper conductor having legs 90 cms made out of 50x50x6 mm angle iron grouted on brick masonary platform upto 45 cms. Brick masonary platform should be 60 cms above the Ground Level. Comprising the following:- .Note:- (i) The panel shall be front operated with cable entry from the bottom with cable glands. Earth bus shall be part of the main feeder pillar. (ii) Fabrication of feeder pillar box to be approved by CPRI width of the panel not less than 75 cms. (iii) Cost for construction of platform for panel of brick masonary work in CM 1:6 with foundation PCC 1:4:8 type D-2 including plaster work, PCC copping 1:2:4 (40 mm thick stone aggerate), deemed to be included in the item rate. No Extra payment will be made. (iv) MCCB's should be connected with extensions terminals at both side (incoming and outgoing). (a) 01 set of 600 Amps TPN aluminium bus bar of suitable length and of crossection as per design with colour codding. Bus bars shall be designed to with stand a fault level of 36 KA at 415 volts. (b) MCCB 400 Amp 4 pole 36 KA, thermal and magnetic releases with Ics=100%Icu. conforming to IS/IEC 60947-2 and IEC 60947-2 with short circuit and over load protection. Makes: Legrand(DPX^3) Cat No.422007 or equivalent to Schneider(NSX)/Siemens(3VL) - 01 No as incoming

Supply, installation, testing & commissioning of totally enclosed feeder pillar outdoor type fabricated out of 3.15 mm thick CRCA sheet dust and vermin proof powder coated double door type (independent cabin including locking arrangement for each MCCBs, bus bar chamber enclosed complete suitable for operating on 415 Volt 50 Hz AC supply internally wired with copper conductor having legs 90 cms made out of 50x50x6 mm angle iron grouted on brick masonary platform upto 45 cms. Brick masonary platform should be 60 cms above the Ground Level. Comprising the following:- .Note:- (i) The panel shall be front operated with cable entry from the bottom with cable glands. Earth bus shall be part of the main feeder pillar. (ii) Fabrication of feeder pillar box to be approved by CPRI width of the panel not less than 75 cms. (iii) Cost for construction of platform for panel of brick masonary work in CM 1:6 with foundation PCC 1:4:8 type D-2 including plaster work, PCC copping 1:2:4 (40 mm thick stone aggerate), deemed to be included in the item rate. No Extra payment will be made. (iv) MCCB's should be connected with extensions terminals at both side (incoming and outgoing). (a) 01 set of 500 Amps TPN aluminium bus bar of suitable length and of crossection as per design with colour codding. Bus bars shall be designed to with stand a fault level of 36 KA at 415 volts. (b) MCCB 320 Amp 4 pole 36 KA, thermal and magnetic releases with Ics=100%Icu. conforming to IS/IEC 60947-2 and IEC 60947-2 with short circuit and over load protection. Makes: Legrand(DPX^3) Cat No.422006 or equivalent to Schneider(NSX)/Siemens(3VL) - 01 No as incoming

Supply, installation, testing & commissioning of totally enclosed feeder pillar outdoor type fabricated out of 3.15 mm thick CRCA sheet dust and vermin proof powder coated double door type (independent cabin including locking arrangement for each MCCBs, bus bar chamber enclosed complete suitable for operating on 415 Volt 50 Hz AC supply internally wired with copper conductor having legs 90 cms made out of 50x50x6 mm angle iron grouted on brick masonary platform upto 45 cms. Brick masonary platform should be 60 cms above the Ground Level. Comprising the following:- .Note:- (i) The panel shall be front operated with cable entry from the bottom with cable glands. Earth bus shall be part of the main feeder pillar. (ii) Fabrication of feeder pillar box to be approved by CPRI width of the panel not less than 75 cms. (iii) Cost for construction of platform for panel of brick masonary work in CM 1:6 with foundation PCC 1:4:8 type D-2 including plaster work, PCC copping 1:2:4 (40 mm thick stone aggerate), deemed to be included in the item rate. No Extra payment will be made. (iv) MCCB's should be connected with extensions terminals at both side (incoming and outgoing). (a) 01 set of 300 Amps TPN aluminium bus bar of suitable length and of crossection as per design with colour codding. Bus bars shall be designed to with stand a fault level of 36 KA at 415 volts. (b) MCCB 200 Amp 4 pole 25 KA, thermal and magnetic releases with Ics=100%Icu. conforming to IS/IEC 60947-2 and IEC 60947-2 with short circuit and over load protection. Makes: Legrand(DPX^3) Cat No. 420218 or equivalent to Schneider(NSX)/Siemens(3VL) - 01 No as incoming

Supply & laying GI pipe light grade 100mm bore under road, path or along poles as cable protection.Make:-TATA/JINDAL/PRAKASH SURIYA complete and all as specified directed by engr-in-charge.

-ditto- but size 40mm bore complete and all as specified directed by engr-in-charge.

M&L for Framed work of steel structure GDE Fe410-0 or Fe 310-Oas in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled or weilded for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete and all as specified directed by engr-in-charge.

S&F chainlink fencing pvc coated green colored 4mm dia galvanised steel wire, 150x100mm mesh, made up into mattresses or cages, lapped, wired and laid in position, including closing after filling complete all as specified and directed by engr-in-charge.

M&L hardcore of broken stone of gauge exc 63mm & n.exc 100mm deposited spread and leveled in layers n.exc 15cm thick watered and well rammed to a true surface. complete and all as specified directed by engr-in-charge.

Material and labour for HDPE pipe of size 40 mm dia grade PE 63 rating PN 10 suitable for protection of strip.

Supply and fixing 1100 volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheathing of PVC tape and over all PVC sheathed in service connection suspended by insulating hangers not more than 1 metre apart incl 4mm dia GI suspension wire one twin core cable flat or circular 6 sqmm 2 core multistranded. complete all as specified by Engr-in-charge.

CELMAC REGD

M/S TRIKUTA BUILDERS