PROVN OF SQUAD POST WALL CLADDING TOILET BLOCK AND OTHER ALLIED WORKS AT GMS UNDER GE I GOS

Amount

Excavation in trenches in soft / loose soil, not exceeding 1.5 metre wide & not exceeding 1.5 metre deep; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sqm on plan including getting out, complete all as specified & directed.

Excavation in trenches in soft / loose soil, not exceeding 1.5 metre wide & depth exceeding 1.5 metre but not exceeding 3.00 metre deep; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sqm on plan including getting out, complete all as specified & directed.

M&L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate in foundations, filling & mass concrete complete all as specified & directed.

M&L for Reinforced Cement Concrete (design mix) M-30 (20 mm graded stone aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles & mass concrete complete all as specified & directed.

M&L for Reinforced Cement Concrete (design mix) M-30 (20 mm graded stone aggregate) in Columns, pillars, piers, posts & struts complete all as specified & directed.

M&L for Reinforced Cement Concrete (design mix) M-30 (20 mm graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified & directed.

M&L for Reinforced Cement Concrete (design mix) M-30 (20 mm graded aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified & directed.

M&L for Reinforced Cement Concrete (design mix) M-30 (20 mm graded aggregate) in Chajjas complete all as specified & directed.

M&L for TMT Bars 10mm dia & over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified & directed.

M&L for TMT Bars 5 mm dia & over upto & including 10 mm dia in stirrups, spaces & binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified & directed.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft & raft beams, sides & soffits (if any) of foundation & plinth beams; & similar work; vertical or to batter for fair finished surfaces complete all as specified & directed.

M&L for Formwork to sides of square, rectangular or polygonal pillars, posts, struts, piers, columns & stanchions for fair finished surfaces complete all as specified & directed.

Formwork to sides and soffits of floor or roof beams, lintels,cantilevers etc complete all as specified & directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs,CB slab, landings and similar work, n.exc 200mm thick (Horizontal or slopping) for rough finished surfaces complete all as specified & directed.

Returning, filling in any type of soil, including spreading, levelling, watering and well ramming in layers not exc 25 cm. Complete all as specified & directed.

Removing surplus excavated material (soil) to a distance not exceeding 50 metre & depositing where directed at a level not exceeding 1.5 metre above the starting point, including spreading. Complete all as specified & directed.

M&L for Brick work with fly ash bricks straight or curved on plan exceeding 6 m mean radius complete built in cement mortar 1:6 complete all as specified & directed.

M&L for Brick work with fly ash bricks straight or curved on plan to any radius in half brick thick walls complete built in cement mortar 1:6 complete all as specified & directed.

M&L for rendering 10 mm thick cement plaster with cement mortar(1:6) on other than fair faces of brick work or concrete surfaces and finished even and smooth without using extra cement complete all as specified & directed.

M&L for rendering 5mm thick cement plaster with cement mortar(1:3) on concrete surface as in ceiling finished even and smooth without using extra cement complete all as specified & directed.

M&L for rendering 15mm thick cement plaster with cement mortar(1:4) on fair faces of brick work or concrete surfaces and finished even and smooth without using extra cement with using water proofing compound complete all as specified & directed.

M&L for preparation of new treated surfaces and applying three coat of white wash to walls complete all as specified & directed.

M&L for preparation of new treated surfaces and applying three coat of white wash to ceilings complete all as specified & directed.

M&L for preparation of new treated surfaces and applying two coat of cement based paint to walls complete all as specified & directed.

M&L for Preparation of new plastered surfaces and applying two coats of OBD over a coat of alkali resistant primer on walls complete all as specified and directed.

M & L for preparation of newly plastered surfaces of ceiling and applying 2 mm thick wall care putty including preparation of new plastered surfaces complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall or concrete surfaces and applying 2 mm thick wall care putty complete all as specified & directed.

M&L Hardcore of gauge n exc 63mm, deposited, spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L 100 mm thick PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in sub floors somplete all as specified and directed.

M&L PCC 1:2:4 type B1 using 20 mm graded stone aggregate average 25 mm thick as in floors finishes as levelling course complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 type C 2 using 40 mm graded stone aggregate as in plinth protection complete all as specified and directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube, fixing in same opening complete all as specified and directed

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top, bottom and side rails, MS frame shall be covered with heat molded plain colour PVC’C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stile and plain colour PVC sheet for top rail lock rail &bottom rail on either side and as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fixed in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement supplying and fixing in the frame at site complete all as specified and directed.

S&F Butt hinges 100 mm, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S&F Extruded aluminium alloy handles fabricated type anodised of size 150mm complete all as specified and directed.

S&F 150 mm size Aluminium anodized barrel Tower bolts of extruded section and fixed complete all as specified and directed.

S&F factory made UPVC any colour casement openable door made of extruded profile with wall thickness of 2.3mm (+-2mm) door profile with hollow sections frame 60mm x 58mm, sash 60mm x 78mm profile one vertical length will be mitred and fusion welded at all corners incl drilling of holes for fixing haradware and making arrangement for fixing of hardware. EPDM gasket 1.2 (+-0.2mm) thick galvanised steel frame (28mm x 21.5mm) sash (31mm x 27mm), to be inserted in requried profile frame will be fixed to the wall with 8mm x 100mm long fasterners.. Hardware : door handle mad of zinc alloyed powder coated, corner striker, secondary strikers, Cylinder, Door transmission gear made of mild steel with multi point locking system with striker, 3D hinges of zinc alloyed powder coated complete all as specified and directed.

S&F factory made UPVC white colour Slinding Window three track made of extruded profiles with wall thickness of 2.3mm (±0.2mm), Window profile with hollow section with multi chamber, frame (88mm X 52mm), sliding sash (42mm X 67mm), Sliding mesh sash (42x57mm), sliding interlock (one vertical length in each shutter) (45.5mm X 28mm), glazing bead (24.5mm X 16mm) will be mitered, cut and fusion welded at all corners, including railing of holes for fixing hardware and drainage of water etc, making arrangement for fixing of hardware, EPDM gasket 1.2 ± 0.2mm thick galvanised steel frame (30mm x 18mm) 2 Nos, sliding sash (30mm X 18mm) 2 Nos, sliding mesh sash (26mm X 10mm), profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners. Haradware (tough lock of zinc alloyed (white powder coated), steel roller system, stainless steel wire cloth 0.36mm nominal dia of wire and average width of apaerture 1.40mm and required accessories etc complete all as specified and directed. Note : The unit rate includes cost of glass and all other connected accessories)

S&F 7mm thick aluminium grills of make "Decogrill' model DG 104 surrounded by aluminium 'C' channel with mesh size 75 X 75mm complete all as specified and directed.

S&F Full pedestal wash basin with fixing accessories set (excluding pillar tap) of size 560X430X195 mm complete all as specified and directed.

S&F Pillar cock long neck with aerator Chromoium plated cast copper alloy for 15 mm bore complete all as specified and directed.

S & F in repairs sheet Glass Shelf assembly consisting of 5.5 mm glass sheet shelf 12 cm wide with cromium plated bracket guard and railing 60 cm long complete aal as specified and directed.

S&F 600 mm long single towel rail stainless steel, between flanges etc. complete aal as specified and directed.

S&F 15 mm bore angle stop cock, cast copper alloy with long shank and cup (concealed type)/any type screwed down high pressure with crutch & butterfly handle screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F PVC connection 15 mm bore, 450 mm long complete with both ends unions complete all as specified and directed.

S&F CP Soap dish in bathroom complete all as specified and directed

S&F Towel rack 600 mm long without lower hangers but with 3 hooks in bathroom complete all as specified and directed

S&F Overhead shower 100 mm dia round shaped single flow with air effect (ABS Body & Face plate chrome plated) with rubit cleaning system complete all as specified and directed

S&F bib tap Chromoium plated , cast copper alloy 15 mm bore with wall flange complete all as specified and directed.

S&F Wall mixer non telephonic shower arrangement with connecting legs and wall flanges complete all as specified and directed.

S&F Floor mounted coupled WC with PP soft close seat cover, hinges, fixing accessories and accesorries set size 410 x 720 x 800 mm, S trap - 250 mm including cistern with cistern fittings for 81751 P & S complete all as specified and directed.

S & F CP hand shower (health faucet) with 1.0 mtr long easy flex tube for 15 mm bore complete all as specified and directed.

M&L non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangle) area of each tile exc 0.11 sqm but n exc 0.18 sqm jointed in neat cement slurry and pointed in white or colour cement to match the shed of tiles including screed bed or bedding layer 15 mm thick in cement mortar 1:4 complete all as specified and directed

M&L glazed coloured ceramic tiles in vertical surface size 350x250x7mm/ 450x350x7mm thick glazed tiles such as skirting and riser over and including rendering fair faces of brick work 10 mm thick in CM 1:4 complete all as specified and directed

S & F 1000 litre rotational moulded polythylene water storage tanks (cylindrical vertical with closed top) hoistes and fixed in position complete all as specified and directed.

M&L for Cutting into existing manholes for connecting new drains of dia 150 mm, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed

S & F 150 mm salt glazed stone ware drain pipe laid in trenches and jointed complete all as specified and directed

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in concrete bed to drain pipe including packing under, and haunching against the sides of pipes after they are laid and tested for 150mm dia pipe complete all as specified and directed.

S&F in repairs 100 mm dia cast iron floor trap with grating incl jointing waste pipe fixed in CM type B1 1:2:4 complete all as specified and directed.

S&F in repairs 100 mm dia cast iron nahani trap with grating incl jointing waste pipe fixed in CM type B1 1:2:4 complete all as specified and directed.

M & L providing precast cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregates) in landing ,cover slab etc set in cm 1:4 complete all as specified and directed.

M&L 110 mm bore PVC (SWR) pipes, single socketed, in any length, with rubber ring joints fixed on wall Including PVC clamp complete all as specified and directed.

M&L PVC (SWR) bends, 110 mm bore any radius complete all as specified and directed

M&L PVC (SWR) vent cowl, 110 mm bore complete all as specified and directed

S&F in repair 100 mm bore stack clamps out of 50x5mm by flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof etc complete all as specified and directed.

M&L PVC(SWR) gully trap 125/110 mm,setting and jointing with solvent cement complete all as specified and directed

M&L Water proofing treatment on "Non approachable / non accessible and approachable roof" surface (Horizontal & Vertical surfaces) in following sequence through manufacturer / authorized applicator of the manufacturer including taking down of existing roof treatment, properly cleaning & drying the concrete surfaces complete (i) Applying a coat of oxidised bitumen based solvent primer @ 0.3 Kg / Sqm (ii) Applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 kg/ Sqm incl cleaning surfaces. (iii) Laying unrolled over the bitumen coated surface, polymeric water proofing membrane Hyperplas standard wt not less than 3kg /Sqm with 100 mm over laps shall be sealed by flame as per manufacturers instruction. (iv) Applying two coats of bituminous aluminium paint including preparation complete

M&L for PCC 1:2:4 type B0 (Using 12.50 mm graded stone aggregate) in roof padding/kerbs/sunken slab etc complete all as specified and directed.

M&L 10 mm thick rendering on roof surfaces/concrete surface in CM 1:4 complete all as specified and directed.

M & L 40mm thick PCC 1:2:4 damp proof course to horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

M&L Moorum / Red bajri filling in floors or pavings, laid in layers n.exc15 cm thick spread levelled and rammed incl watering etc complete all as specified & directed.

M & L 100 mm thick Cement concrete type C-2, 1:3:6 (using 40 mm graded crushed stone aggreates) as in flooring finished even and fair complete all as specified and directed.

M&L 40 mm thick PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in floor finishes laid in panels & finished even and smooth using extra cement complete all as specified and directed.

S&F rolled mild steel section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connected plates of grade Fe 410-W (Gde E-250) quality A complete all as specified and directed

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L PCC 1:2:4 type B1 using 20mm graded stone aggregate in coping and the like including weathering slightly rounded/chamfered angles & throating with & including necessary formwork use. complete all as specified & directed.

Supply only liquid water proofing compound ISI marked complete all as specified & directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in drains/surface channel complete all as specified & directed.

EXTRA for forming fair finished channel 45 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc.complete all as specified and directed.

M&L for Excavation over areas, n exc. 1.50 m deep & getting out in soft/ loose soil complete all as specified & directed.

M&L PCC 1:3:6 type C1 using 20mm graded stone aggregate in benching and the like including weathering slightly rounded/chamfered angles & throating with & including necessary formwork use. complete all as specified & directed.

M&L 15mm thick cement plaster in one layer in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified & directed.

M&L for RCC Pipe Class NP3, 300 mm dia laid & jointed complete with collars, complete all as specified & directed.

Taking down cement or cement lime plaster of any description including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for Washed stone grit plaster on exterior wall in two layers, under layer 12 mm cement plaster CM 1:4 owing the under layer with scratching tool, applying cement slurry on the under layer @ 3 kg of cement per sqm, top layer 15 mm cement plaster 1:1/2:2 ( 1 Cement : 1/2 coarse sand : 2 stone chipping 10 mm nominal size) in panels with groove all around as per approved pattern incl scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified and directed.

M&L for point wiring with cable PVC insulated but unsheathed, 1.5 Sqmm, stranded copper conductor in and including PVC concealed conduit incl continuous earthing with cable PVC insulated 1.5 Sq mm copper conductor, MS box , including laminated top sheet cover,washer & screw complete all as specified and directed for the following : (a) One light point controlled by one, one way switch.

(b) One exhaust fan point controlled by one, one way switch.

(c) One 3 pin 5 Amps switch socket outlet point controlled by one switch on the same board.

(d) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

S & F switch piano (Flush type) 5 amps, 240 Volts, single pole one way.

S & F for socket outlet 2 in 1, 6 pin, 5 and 15 amp, 230 Volts complete all as specified and directed.

S & F ceiling rose, bakelite three terminal

S & F LED tube light along with fixture,18W complete all as specified and directed.

S & F sheet metal enclosure double door MCB DB, SPN 4 way complete all as specified and directed.

S & F street light fitting LED type of 45 watt New generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP65 roadway luminaire with high power LEDs (8x2.5 HPLED/LS) as light source and electronic driver. mounting bracket suitable to house the light fittinhg , with its Galvanised Flat Iron clamps conntected nuts bolts etc complete all as specified & directed. (Note : warrenty of PCB @ 3years)

S & F MCB SPN 6-20 Amp 10 KA 240 Volts

S & F MCB, SP 6 to 10 Amp 240 Volts rating

S & F exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver complete all as specified and directed.

M & L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to GI earth wire 4mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia. medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mm dia, PCC Chamber, CI frame and cover, MS funnel with wire mesh all as shown in electrical plate no 3 of SSR part I including excavation and earthwork in any type of soil/strata and testing on completion. Note :- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted.

S & F for lamp holder , PVC / Polycarbonate type with back plate suitable for batten/ slanting fittings complete all as specified and directed.

S& F highly efficient LED Bulb 10 W as ready replcement complete all as spd and directed

S& F water heater storage type electric cap 25 litres BEE 5 star rated for Accn complete all as spd and directed

Supply , laying and testing XLPE insulated, armoured heavy duty electric cable, screened PVC bedded, with aluminium conductor 1100 V grade, laid in trenches/along poles, ducts or through sleeve of size 16 spmm 4 core complete all as specified and directed.

Supply and providing sand cushioning with dry clean sand 15 cm below cable and 8 cm above the cable complete all as specified and directed. Note : Punned thickness shall be measured for the purpose of payments.

Supply and laying flyash building bricks laid in trenches for LT cable protection with length of brick perpendicular to length of cable complete all as specified and directed.

Boring across the road/hard surface horizontally with mechanical boring equipments not less than 50 mm bore complete all as specified and directed.

S&F MCB SPN 6-32 Amps complete with necessary elect connections at the exisitng DB with two way DB Enclosure complete all as specified and directed.

S&F 40 mm bore Galvanised steel tubing light grade including all fittings, laid in trenches , fixed to walls or on poles etc after taking out the rusted out/wornout pipes complete all as specified and directed.

S&F PP-R 3 layer polpropylen random copolymer concealed pipes SDR- 7.4 (PN- 16) unstabilized and antimicorbial fusion welded having thermal stability for hot & cold water supply all PPR plain & brass threaded polypropylene of size 25 mm (OD) and random fittings laid in trenches complete all as specified and directed.

S& F of PP-R gate valves (Brass inlet) as per requirement of size 25 mm dia complete all as specified and directed.

Making connection of PP-R distribution branch with PP-R main of Size 25 mm OD by providing and fixing tee including cutting and making fusion joint etc complete all as specified and directed.

M & L for construction of brick masonry value pit chamber of size 600mm x 600mm x450mm including necessary excavation and earth work in any type in CM (1.4) complete with valve pit cover (steel) with locking arrangement complete all as specified and directed.

Surface excavation n.exc 30 cm deep and getting out in any type of soil complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

S&F Mild steel TMT bars 8mm dia and over, cut to length, spacers and binders and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for rendering 5mm thick in CM 1:6 on brick or concrete surface, finishing even and smooth without using extra cement complete all as specified and directed.

M&L preparation of newly plastered surface of walls and applying two coats colour wash over one coat of white wash complete all as specified and directed.

Supply only water proofing compound of approved make.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing complete all as specified and directed. Fe 410 -W (Gde- E- 250) quality- A

M&L for preparation of new surfaces of steel and iron surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L plain, solid, 2nd cl hard wood straight Chowkats and frames wrought framed rebated on the solid rounded or chamfered put together with pinned at joint etc complete all as specified and directed.

S&F 30mm thick 2nd class soft wood (Kail) glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc divided into squares with plain chamfered or rounded, mitred and rebated shash bars, any numbers, edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part I, Section 8 , Clause 8.24 (b), complete all as specified and directed.

S&F 35 mm thick 2nd class soft wood (Kail) plain, framed, panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged) or of veneered particle board, medium density, wood particle board with commercial face veneered complete all as specified and directed.

S&F MS flat iron as in hold fast etc and similar work complete all as specified and directed.

S&F 75 mm long mild steel butt hinges, medium weight, cold rolled and fixed complete all as specified and directed.

S&F 75mm long aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 100 mm long aluminium handles, cast type, anodised complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

M&L for preparation of wood and wood based surfaces of any description not otherwise described over 10 cms width or girth and applying 2 coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty complete all as specified and directed.

S&F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aparture 1.4 mm complete all as specified and directed.

Demolition of Cement Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified & directed.

M&L for 10 mm thick heavy duty exterior designer tiles of size 300 mm x 300 mm as in floor set, jointed in neat cement slurry and pointed with grey cement and pigment complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15 mm thick in CM 1:4 for laying floor finishes complete all as specified and directed.

M&L for Rendering on fair faces of brick work or concrete surfaces of wall 15 mm thick in CM 1:6 and to be finished even and smooth without using extra cement complete all as specified and directed.

M & L coloured vitrified tiles Light shade 10 mm thick (square/rectangular) polish area of each tiles n exc 0.36 Sqm coloured cut to required size set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles as in floor incl 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

M & L coloured vitrified tiles 10 mm thick (square/rectangular)polish area of each tiles n exc 0.36 Sqm coloured cut to required size set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles but in vertical surfaces incl 10 mm thick rendering in CM 1:3 complete all as specified and directed.

Cutting holes into or through cement concrete slabs, chajjas, etc reinforced or otherwise superficial area exc 250 Sq cm but n.exc 500 Sq cm complete all as speified and directed.

M&L Drilling holes into existing RCC column/beam to a depth of not less than 100mm, inserting reinforcement bar and grouting with ultimate performance epoxy mortar (HIT-RE 500 V3 epoxy anchor of M/s Hilti or equivalent) for re-bar connections and heavy anchoring complete all as per manufacturer's instructions and directed

S&F 12 mm thick plain Gypsum Board False Ceiling with GI frame including all necessary drilling cutting to fix electric items complete all as specified and directed with following:- (a) GI Grid channel 30x25x20 mm of 24 gauge fixed with rawl plug and screw 450 mm centre to centre alongwith perimeter walls. (b) GI channel made to shape 50x40x40 mm of 24 gauge placed @ 600 mm centre to centre from perimeter at wall except long wall (in one span). (c) GI intermediate runners of size 45x10x10 mm of 24 gauge fixed @ 1200 mm centre to centre leaving frame of one side walls (in other span). (d) GI sheet 25 mm wide and 20 mm gauge suspended fixed with steel fastner to roof ceiling and 1200 mm centre to centre including pluging of RCC Slab. (e) 12 mm thick gypsum board filling joints with POP and finishing complete with two coat of plastic emulsion paint over one coat of primer on ceiling.

S&F Pre- painted galvalume aluminum zinc corrugated steel based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping serews complete all as specified and directed.

M&L for Fe 410-W (Gde E-250 quality A) Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed.

M&L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161- 1979 grade St.-240 complete all as specified and directed.

M&L for preparation of new steel surfaces of any description n exc 10cm in width or girth and priming with red oxide zinc chrome and applying two coat of synthetic enamel paint complete all as specified and directed.

Excavating in post holes (or similar holes) each n.exc 0.5 cum getting out making good the disturbed surface if required in soft/ loose soil complete all as specified and directed.

M&L for PCC 1:3:6 Type C-2 using 40 mm graded stone aggregate in foundation filling and mass concrete complete all as specified and directed.

S&F Angle iron posts and rails,drilled and struts in fencing including cutting tops to shape as directed, driiling holes, notching for wire, etc, flat iron fillets (for secruing wire mesh etc) including all necessary drilling, bolting or riveting, etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F mild Screw bolts (Machine made) with hexagonal or square head at one ends and to fitted with washers and one hexagonal or square n.exc 15cm long, dia of neck 11 to 15mm complete all as specified and directed.

S&F PVC coated chain link of 3.16mm dia mild steel galvanised fencing of mesh size 75 mmx 75mm as per IS : 2721-2003 weight n exc 4.00 kg per sqm complete all as specified and directed.

Supply, laying and testing XLPE insulated, armoured heavy duty electric cable, screened PVC bedded, with aluminium conductor 1100 V grade, laid in trenches/ along poles, ducts or through sleeve for size 10Sqmm 2 core complete all as specified and directed (connection from Tech Block Panel board) : - Note: Earth work, sand cushioning and bricks will be measured and paid separately under relevant items Make:- Havells / polycab / cci / nicco / Gloster

S & F ceiling fan regulator electronic step type complete all as specified and directed. -Make : Anchor/Havells/Standard or equivalent

Supply and fix ceiling fans complete with accessories 230 V , 1200 mm sweep BEE 5 star rated all as specified and as directed. Make cat part No: Premium Summercool 1200mm (white) of Orient/Crompton or equivalent

Supply & fix LED tube light along with fixture,18W complete all as specified and directed

M&L for GI tubing 25-32mm dia medium grade, mounting bracket and end nipple/nozzle of the bracket of size suitable to house the light fittinhg , with its Galvanised Flat Iron clamps with suitable set of nuts, bolts, washers etc complete all as specified and directed

Supply and fix Bldg security light fitting LED type of 20 watt New generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP65 roadway luminaire with high power LEDs (8x2.5 HPLED/LS) as light source and electronic driver. mounting bracket suitable to house the light fitting , with its Galvanised Flat Iron clamps conntected nuts bolts etc complete all as specified & directed (Make C&S / WIPRO / Bajaj / Phillips / Havells) (Note : warrenty of PCB @ 3years)

S&F PP-R 3 layer polpropylen random copolymer concealed pipes SDR- 7.4 (PN- 16) un Stabilized and antimicorbial fusion welded having thermal stability for hot & cold water supply all PPR plain & brass threaded polypropylene of size 32 mm dia (OD) and random fittings laid in trenches complete all as specified and directed.

S& F of PP-R gate valves (Brass inlet) as per requirement of size 32 mm (OD) complete all as specified and directed

Making connection of PP-R distribution branch with PP-R main of Size 63 mm OD by providing and fixing tee including cutting and making fusion joint etc complete all as specified and directed.

M/s Ats Electricals

G.KRISHNA MURTHY AND PARTNERS

M/S JAGANNATH SASMAL

M/s MAA BHAIRABI ENTERPRISES

M/S. KISHAN ENGINEERING