NIT NO: 56 RAIPUR DATED: 13.10.2026

BOQ FOR SOCIETY BUILDING AT BRAHMAN PARA, WARD 43 ZONE 04

S.N PARTICULAR’S QUANTITY RATE UNIT AMOUNT

Providing and laying nominal mix reinforcement cement concrete with crushed stone aggregate using concrete mixer in all work upto floor five level excluding cost of reinforcement and form work.(ii)1:1½:3 (1 cement : 1½ coarse sand :3 graded stone aggregate 20mm nominal size).b) M-20

Providing and placing in position reinforcement for R.C.C work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire in foundation & plinth all complete:thermo Mechanically treated steel bars FE 415

3 Centering & Shuttering

a Providing and fixing formwork ncluding,shuttering,strutting,staging, propping bracng etc. complete and including its removal at levels, for: (i)Foundation, footings, bass of columns and plinth beam in any. Shape and size

b (v) Columns,pillars Piers and likes-rectagular or square in shape

c (viii) Beams,lintels,cantillevers & walls

d (vii) Suspended floors,roofs,access platform,balconies (plain surfaces ) and shelves (cast in stu)

(a) Brick work with modular well burnt clay bricks of crushing strength not less than 25 kg/sqcm and water absorption not more than 20%in foundation and plinth in : Cement Mortor 1:6

(b) Extra for brick work in superstructure:

Above plinth level for every floor or part there of in addition to rate for foundation and plinth

Super structure

5 (B)Half brick thick brick masonry with modular well-burnt clay bricks of crushing strength not less than 25 kg/sqcm and water absorption not more than 20% in superstructure above plinth level .Page No.45,Item No.7.10 (ii)Cement Mortar 1:4 (1Cement :4 coarse sand ) extra for half brick work in super structure above plinth lvl for every story or part there of in addition to rate for upto plinth lvl.

115.85 Per Sqm.

6 Plastering work

Providing & making 12 mm thick cement plaster of mix: (iv) In Cement mortar 1:6 (1 Cement :6 fine sand)

7 Providing & making 15 mm thick cement plaster on the rough of side of single or half brick wall of mix: (iv) In Cement mortar 1:6 (1 Cement :6 fine sand)

8 Providing & making 6 mm thick cement plaster of mix:(i)In Cement mortar 1:3 (1 Cement :3 fine sand)

9 Providing wood work in frames of doors, windows, clearestory windows and other frames wrought framed and fixed in position.b) Sal, bijasal, benteak, khair, haldu

10 Providing and fixing flush door shutters,confirming to IS 2202 (Part -1) interior grade, commercial type, core of block board construction with frame of first class hard wood and well matched commercial ply veneering with vertical grains, cross bands and face veneers on both faces of shutters excluding hinges(ii)35 mm thick(single leaf)

11 Providing and fixing bright finished brass sliding door bolt with nuts and brass polished MS screws complete: (ii)250x16 mm

12 Providing and fiixing bright finished brass tower bolts(barrel type) with brass polished MS screws complete:iii)150x10 mm

13 Providing and fixing bright finished brass door handles with brass polished MS screws complete:(ii)100 mm

14 Glazed window

Providing and fixing factory made ISI marks steel doors, windows and ventilators side/top/center hung made up of standard rolled steel section conforming to IS 1038:1968 (viz F7D,F4B,K11and K12B) joints mitred and flash butt and sash bars tenoned and riveted/weded with 10 cm long lugs of size 15x3mm embedded in cement concrete block 15x10x10 cms of 1:3:6(1 cement :3 rawl plugs and screws or with bolts and nuts as required including providing and fixing of hinges, pivots, handles, pags, stays rolling deviced, locking arrangemnts, spring catch etc. as required complete including applying a priming coat of red oxide zinc chormate primer.

22 kg per sqm 443.52 kg

15 Providing and fixing 3 mm fibre glass pane with steel glazing clips and special metal sash uptty of approve make in steel doors, widiows, ventilators.

75% of window area 14.11 Sqm.

16 Providing and fixing factory made 25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded PVC section of the size of 762 mm X 25mm or less as per requirement with an avarege wall thickness of 1mm ±0.3mm. PVC foam end cap of size 23x10 mm are provided on both vertical edges to ensure the overall thickness of 25mm. An M.S. tube having dimensions 19 mm x19 mm is inserted along the hinge side of the door. Core of the door shutter should be filled with High Density Polyurethane foam. The Top & Bottom rdges of the shutter are covered with an end-cap of the size 25 mm X 11 mm.Door shutter shall be reinforced with special polymeric reinforcements as per manufactures' specification

Providing and fixing M.S. grill of approved pattern made of M.S. flats or square or round bars welded to steel frame of windows etc. including applying a priming coat of red oxide zinc chromate primer. with frame

Preparation of wall surface by applying a cost of putty comprising of chalk mitti, varnish and white lead in ratio 2½:1:1(2½ kg chalk mitti:1 litre varnish : 1 kg white lead) respectively, sand papering and making the surface smooth to proper shape and presentable conditions.

19 Distempering

Wall painting with acrylic luxury emulsion (plastic ) paint (top most approved branded quality ) to give an even shade. On new work (two or more coats)

20 Exterior Paint

Painting new exterior surface with PREMIUM ACRYLIC SMOOTH exterior paint of required shade as per manufacturers specification to give protective and decorative finish including cleaning washing of surface etc complete with: on new work ( two or more coats applied at 1.43ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm)

Providing and laying vitrified floor tiles with double charge/ multi charde printing with water absorption less than 0.5% and conforming to IS : 15622 of approved make in all colours and shades and size mentioned below (+/-10mm), laid on 20mm thick cement mortar 1:4 (1 cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete: (i)Size 600x600mm.

25 mm thick KOTA stone slab flooring over 20 mm (Average ) thick base of cement mortar 1:4 laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding rubbing and polishing etc. compete (Area of slab to be 0.20 sq.m and up to 0.50 sq.m)

24 Painting onnew work (two or more coats) to give an even shade with:(ii)Premium synthetic enamel paint