Tiruvannamalai Cultural Museum

Earth work excavation for foundation by Mechanical means for Isolated & Combined Footing etc in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 100 mts and clearing and levelling including dressing of sides and raming of bottoms etc., complete complying with standard specification and as directed by the departmental officers.

Earth work Open excavation by Mechanical Means for Open Earthwork in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 100 mts and clearing and levelling including dressing of sides and raming of bottoms etc., complete complying with standard specification and as directed by the departmental officers

Supplying and filling in foundation, basement, etc with filling M-sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supply and filling in foundation and basement with Gravel in layers of not more than 15cm.thick well rammed watered and compacted with surface vibrator, watered and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Providing and laying spreading and compacting graded stone aggregate to Wet Mix Macadam(WMM) specification including premixing the material with water at OMC in machanical mix plant carriage of mixed material by tipper to site laying in uniform layers 250mm thick with pavers in SubBase/Base course on well prepared surface and compacting with vibratory roller to achieve the desired density including cost of material,labour charges, rentals for machinery, fuel and all other incidental charges etc., complete.

Supplying and filling 40mm guauge HBGS stone jelly for dispersion trench including loading conveying and unloading and as directed by the departmental officers etc. complete complying with standard specification.

Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc. complete complying with standard specification and as directed by the departmental officers -Mixing by mechanical means

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, Sill slabs etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner , vertical stiffener , side support and Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid).

Supplying and erecting centering for plane surfaces such as RCC Floor/Roof Beam, Lintels, Cantilever Beams, Bed Blocks etc.. with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over Steel adjustable Span of Size 2m x 2m(expandable upto 3.60m) and Silver Oak Joists of Size 10 x 5 cm spaced at 50cm to 60cm c/c and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) Spaced at not more than 50 to 60cm c/c , etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).

Supplying and erecting centering for plane surfaces such as RCC Floor Slab, Roof Slab, Loft, Landing Slabs, etc with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over steel adjustable span of size 2m x 2m (expandable upto 3.60m) and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) , etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).

Supplying and erecting steel centering including necessary supports For plane surfaces such as rectangular or square RCC columns etc. which require only nominal strutting using mild steel sheets made of 10 gauge thick welded with MS angle size 40mm x 40mm x 5 mm and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick).etc..complete in all floors complying with standard specifcation. Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc. using mild steel sheets of size 1200cm x 60cm and 10 BG stiffened with welded mild steel angles of size 40mm x 40mm x 5 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner, Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals. MS Channel Section (ISMC 100) shall be provided as a vertical support @1.20m C/C and with Lateral support of Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) & steel pipes of 20mm dia @ required level/spacing etc. complete complying with standard specifcation and as directed by the departmental officers. (Payment for centering shall be given after the concrete is laid)

Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part thereof but not less than 30 cm, over the initial 3.00 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers.

Providing and laying in position, Standardised Concrete Mix M-25 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350 kglm3 and maximum water cement ratio of 0.50, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

In foundation and basement

for super structure in Ground floor

for super structure in First floor

for super structure in Second floor

for super structure in Third floor

Providing and laying in position, Standardised Concrete Mix M-35 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 425 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

for super structure in First floor

for super structure in Second floor

Providing and laying in position, standardised concrete Mix M-20 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).

In foundation and basement

for super structure in Ground floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel reinforcement grills of all variety like HYSD/CTD/TMTand all grade like Fe 500, Fe550D, Fe 500 D etc., for all RCC works as per design given including cost of steel reinforcement and G.I. binding wire, wastage etc. complete complying with standard specification and as directed by the departmental officers.(Contractor has to make his own arrangements for the supply of steel reinforcement and binding wire)

Upto plinth/Basement level

For Ground Floor

For First Floor

For Second Floor

Design and execution of post tensioning work, including decoiling, the strands, cutting to the required lengths, supplying, laying of HT strands sheathing (GI corrugated ducts 0.3mm thick) jointing with couplers and inserting the strands, profiling, fixing liveend anchorages, including supply of stressing anchorages, suitable for 5-5 & 5-4 tendons, grout vents, making dead end anchorages, including flowering the strands, fixing tendon support bars, supervising the fixing of antibursting reinforcement, stressing the cables, end trimming, grouting the cables, with cement slurry, mixed with admixtures with required tools, plants, and machineries, and consumables etc.

(Shuttering, concreting & reinforcement steel shall be paid under respective items) at all heights including all leads, lifts, coordination, with the post- tensioning agency, preparation of drawings, obtaining approval from the Employer / Architect etc. Rate to include providing water, power, cement and admixture for grouting, packing of sheathing and anchorages blockings, filling of recess pockets after stressing using grouts (cement slurry mixed with approved admixtures) including providing access to post tensioning at all heights including all leads, lifts etc., all complete and as approved and as directed by the Employer Architect but excluding shuttering, concreting & reinforcement steel which shall be payable under respective items separately.

Brick work in Cement Mortar 1:3 (One cement and Three M-sand) using best quality Burnt Clay Brick of size 9" x 4 3/8" x 2 3/4" with class designation of 7.5 conforming to IS 1077-1992 for foundation and basement including Cost of Mortar Plasticizer curing, etc.,complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally other type of bond shall be done as directed by the Executive Engineer in charge.

a)Foundation & Basement

Brick work in Cement Mortar 1:5 (One cement and Five M-sand) using best quality Burnt Clay Brick of size 9" x 4 3/8" x 2 3/4" with class designation of 7.5 conforming to IS 1077-1992 for foundation and basement including Cost of Mortar Plasticizer curing, etc.,complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally.other type of bond shall be done as directed by the Executive Engineer in charge.

Foundation & Basement

Brick work in Cement Mortar 1:6 (One cement and Six M-sand) using best quality Burnt Clay Brick of size 9" x 4 3/8" x 2 3/4" with class designation of 7.5 conforming to IS 1077-1992 for foundation and basement including Cost of Mortar Plasticizer curing, etc.,complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally.other type of bond shall be done as directed by the Executive Engineer in charge.

Foundation & Basement

For super structure in Ground floor

For super structure in First floor

for super structure in Second floor

for super structure in Third floor

Brick partition walls of 11.50cm thickness using best quality Burnt Clay Brick of size 9" x 4 3/8" x 2 3/4" with class designation of 7.5 conforming to IS 1077-1992 in Cement Mortar 1:3 (One Cement and Three CS Sand) using hoop iron reinforcement if found necessary including Cost of Mortar Plasticizer, curing etc. complete complying with standard specification and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

In Ground Floor

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of following size of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Supplying and fixing in position best approved of BIS quality 160mm dia PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification and as directed by the departmental officers

Paving the floor with best approved quality Heritage Patterned customized cement based designer tiles of size 200mm x 200mm x 20mm including corner & inner border tiles laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best approved quality fine polished Granite Stone Slabs of following size and Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., complete complying with standard speicification and as directed by the departmental officers.(The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work)

Labour charge for finishing the top of working table and staircase step portion with nosing arrangements in Granite Slab/tiles including cutting the edges and polishing including cost of polishing materials etc., complete complying with standrard specification and as directed by the departmental officers.

Flooring with ceramic tiles of following size and variety conforming to IS 15622 laid over cement mortar bed of 20 mm thick in cement mortar 1:3 (One Cement and Three crushed stone Sand) with required Cement Slurry and Mortar Plasticizer including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing walls with following best approved quality, white / colour ceramic tiles of sizes 300 X 600mm conforming to IS 15622 of following sizes in Cement Mortar 1:2 (One Cement and Two crushed stone sand),10 thick with Mortar Plasticizer and pointing the joints with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. neatly in all floors, curing, etc., complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothly with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (water proof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the Departmental Officers.( The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (water proof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coats of putty, scrapping the putty area to level the surface smooth, etc.,complete. The putty should be got approved by the Executive Engineer before use on work

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including mortar plasticizer at 200ml per 50Kg of cement used , hacking the surfaces and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc. complete complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 20mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including mortar plasticizer at 200ml per 50Kg of cement used, finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Providing Polymer Coating (Water Proof Coating) for sunken portion of toilet with following specification and the surface shall be cleaned to remove all dust, foregin, matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier. The mix shall be stirred thoroughly until no bubbles remain in the mix. Any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the departmental officers etc. The rate inclusive of cost of materials and labour, etc., complete.

Supplying and fixing of fine Cuddapah slab of 38 / 40 mm thick for Cup - board arrangements in brick wall including levelling to correct alignment etc complete complying with standard specification and as directed by departmental officers

Paving pre-polished concrete anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in accordance with IS 1443 in Cement Mortar 1:3 (One Cement and Three crushed stone sand), with required Cement Slurry and Mortar Plasticizer, 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Supplying and fixing Teakwood Entrance Door with a size 5.40m x 2.90m with four leaves as per the design approved by the departmental officers. The outer frames are, 1 horizontal and 4 verticals of size 150 x 100mm scantlings. Shutter frames are 100 x 50mm scantlings. The shutter shall have 2.40m hight with two panels having 1/3 at bottom and 2/3 at top. The panels shall be 40mm thick teakwood planks. The shutter shall have 4 leaves of equal size and openable. The top 2/3 shall be MS grill of approved pattern and bottom 1/3 shall be teakwood planks of 40mm thick and finished with approved pattern with skilled carpentar as directed by the departmental officers. The top portion shall be covered with plain glass of 8mm thick. The rate includes cost of best and approved quality of yeakwood, teakwood reeper of 50 x 25mm size, brass hinges, tower bolt, aldrop, locking arrangements, ornamental Handles, brass screws and labour charges for handlings, fixing charges, conveyance charges etc. The door frame and shutters shall be given two coats of best and approved quality of lac polishing etc., complete complying with standard specification.

Stainless Steel (Salem Stainless Steel) Door Frame - Box Section using Stainless Steel Plate with following thickness with the size of 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel Hold fast etc including dismantling,making necessary chipping and holes in RCC columns, walls with power drills to the extent required ,including providing concrete 1:2:4 inside the box curing etc complete complying with standard specification and as directed by the departmental officers - SS Door Frame with thickness of 1mm/1.60mm.

Supplying and fixing solid core flush shutter of following type with thickness with necessary T.W. internal lipping alround conforming to IS 2202-1(1999) including cost of wind appliances and furniture fittings such as 6 Nos of SS 304 Grade Butt Hinges of size (125mm x 30mm) , 3 Nos. 300x12mm aluminium tower bolt 1 No. 200x12mm aluminium tower bolts 1no. 250x16mm aluminium aldrops, 3 nos. 200mm ‘D’ type aluminium door handle and door stopper with bush etc., complete complying with standard specification and as directed by the departmental officers.

single leaf door

Double leaves door

Manufacturing supplying and fixing of Fully panelled steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x6mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of Steel Parliament Hinges of Size 125mm x 150mm in case of single leaf and 6nos. of Steel Parliament Hinges of Size 125mm x 150mm in double leaves shutter to be provided 6nos. of holdfasts 200 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 4nos. One the top of each shutter, one at lock rail and the other at the bottom are provided.

1no. Aldrop is provided at lock rail section in the door 3 Nos of handle are to be provided, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc.,complete complying with standard specification and as directed by the departmental officers. - Double leaves

Providing of 35mm thick factory made Design Pre-laminated ABS (Acrolynitrile Butadiene Styrene) Door Shutter moulded in different designs, consisting of all round frame made out of water proof solid foam PVC bar of size 20 x 32mm, reinforced by 32 x 32mm - 2 Nos., for vertical made out of LVL (Laminated Veneer Lumber), core material of 32mm thick high density craft paper honey comb board, sandwiched on both sides with pre-laminated ABS sheet thickness of 1.5mm. PVC edge banding of size 0.45mm on the vertical sides. Hardware made out of steel coated butterfly hinges - 3 Nos., for each shutter and ISI make SS round lock complete for finished item of work, complete complying with the standard specification. The door shutter and frame should be got approved from the Executive Engineer before use on work.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying and fixing Mild Steel grills for windows, ventilators etc.,complete complying with standard specifications and as directed by the departmental officers.

Supplying and fixing of rolling shutters Gear Operated Type (from 8 sqm. to 12 sqm. Area) shall be pull and push type made of 18G/3" lathe sections which consist of five main parts such as curtain, lock plate, guide channels rollers and hood cover. These five main parts are made out of special components detailed below: curtain shall be of 18G/3" lath sections cut to required size and filled with heavy cast iron / MS clips. For 8'0"(2.45m) high rolling shutter lath sections provided shall be not less than 37 numbers. Lock plate shall be 10GMS sheet and attached to the side brackets with 20mm square bar.Side brackets shall be of 10G MS plate and cast iron "U" clamps shall be rivetted to the side brackets.

Roller shall be of heavy cast iron pullies fitted with heavy duty "C" class 40mm steel pipe and high tensile high carbon coil springs. 2 springs shall be supplied. Side brackets shall be of 10G MS plate and cast iron "U" clamps shall be rivetted to the side brackets. Roller shall be of heavy cast iron pullies fitted with heavy duty "C" class 40mm steel pipe and high tensile high arbon coil springs - 2 springs shall be supplied. Hood cover shall be of 0.8mm CRCA sheet reinforced with 25mmx25mmx3mm MS angle or gate channel. The rolling shutter in addition to the above should have pulling hook and shall be coated on exposed area with heavy coat of red oxide primer etc., complete.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete

Supply and installation of Anutone (or) Equivalent Brand of Acoustical False Ceiling of subtex nubby, square edge, glass fibre core fully encapsulated ceiling tile of size 595 x 595 x 15mm having volume density 120 Kgs / m3, weight 1.8 / 2.4 / 3 kg / m2 which is suspended by using 0.3mm thick skelet trelis T15 metal grid system. Skelet trelis T15 metal grid system of 600 x 600mm module includes skelet WA15 W30 wall angle with unequal flanges of 15 / 19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the skelet MT15 W36 MainT with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 1200mm centres. Skelet CT15 W12 CrossT with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main T15at 600 mmcenters in the perpendicular direction to the Main T15.

Finally, the skelet CT15W06 CrossT with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in the CT15W12 CrossT in direction parallel to the Main T15 to result in 600 x 600mm module. The subtex nubby square edge of size 595 x 595 x 15mm shall be placed into the grid size of 600 x 600mm. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. The systems to achieve noise reduction coefficient not less than 0.9 NRC, so as to have an neat appearance as directed by the department offices. The cost includes, cost of material, cost of labour, scaffolding, transportation, conveyance, etc. complying to standard specication.

Providing and fixing Acoustic Wall Panelling (equivalent to Armstrong) in channelled wood works perforated panels of width 192mm, thickness of 15mm and length of 2400mm or as per required by the Departmental Engineer made of a high density fibre board with minimum 725 kg./m3 density substrate with a laminated facing as per the approved shade and finish and a melamine balancing layer on the reverse side. The boards shall have a special peforation pattern where the visible surface has a "Helmholtz" fluted perforation of 3mm width and 21mm of visible panel each. The edges of the panels shall be "tongue-and-grooved" to receive special clips for installation. The back of the perforated panel shall have sound absorbing non woven acoustical fleese having NRC of 0.52. The panels shall be mounted on special aluminium splines using clips provided by Armstrong and approved by the Engineer-in-Charge.

Supply and installation on Window and doors jams plywood with laminate etc., complete with standard specifications and as directed by the departmental officers.

Painting two coats of newly plastered wall surface with ready mixed plastic Interior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and painting the walls with two coats of cement paint as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications and as directed by the departmental officers. (The colour and shade of the cement paint shall be got approved by the Executive Engineer before use of work).

Painting two coats of newly plastered wall surface with ready mixed plastic Exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification and as directed by the departmental officers.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and laying of 63mm thick high strength type of interlocking Paver block of approved colour made up of designed concrete mix 1:1:2 using 10-20mm size HBG stone jelly in required shapes and sizes having minimum compressive strength of 40N/mm2 to be laid in fluyring bone pattern with approved non sticking surface at top. The rate is inclusive of levelleing the site, with power compactor and sweeping the sand grouting and also inclusive of transportation charges, loading, unloading and labour charges for laying the paver block etc.,complete and as directed by the departmental officers.

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two crushed stone sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed by the departmental officers. a)50mmdia

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with crushed stone sandcushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two crushed stone sandand Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)

Supply and fixing in position of best Indian make white / colour glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)

Supplying and fixing if marble of 0.61*1.22m.,18/20mm thick in all floors for urinal partition including for labour charges for fixing and polishing etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 5.5mm thick mirror of following size , Shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on works)

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing best approved best quality brass CP soap tray of size 150 x 100mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supplying and fixing position PVC Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing PVC ventilating shaft of 110mm dia (having working pressure 4 kg. / sq.cm) with 3 metre height including cost of PVC cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

75mm dia PVC Soil Pipe

110mm dia PVC Soil Pipe

160mm dia PVC Soil Pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

110mm dia PVC door Tee

75mm dia PVC door Tee

110mm dia PVC Bend

75mm dia PVC Bend

P.V.C Cowl 110mm dia

P.V.C Cowl 75 mm dia

Supplying, laying and jointing UPVC pipes of Class 5 (having working pressure of 10 kg/sq.cm) conforming to IS 4985- 2000 of approved quality and best variety of the following dia including cutting and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) in accordance with IS 7634-3 (2003) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works - External water supply above ground level.

50mm dia UPVC Pipe ( Below GL)

Supplying, laying and jointing UPVC pipes of Class 6 (having working pressure of 12.50 kg/sq.cm) conforming to IS 4985- 2000 of approved quality and best variety conforming to BIS of the following dia including cutting and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) in accordance with IS 7634-3 (2003) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works - External water supply Below ground level.

40mm dia UPVC Pipe

32mm dia UPVC Pipe

Supplying, laying and jointing UPVC pipes of Class 5 (having working pressure of 10 kg/sq.cm) conforming to IS 4985- 2000 of approved quality and best variety of the following dia including cutting, and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) in accordance with IS 7634-3(2003) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works. - Internal water supply - above ground level.

25mm dia UPVC Pipe

20mm dia UPVC Pipe

Supplying UPVC Specials in water supply arrangements (both in internal and external water supply arrangements.Since the labour for cutting, pasting, sundries have already been included under pipe line item of works, no separate provision for fixing UPVC specials needs to be allowed.

50mm dia UPVC Union

40mm dia UPVC Union

32mm dia UPVC Union

25mm dia UPVC Union

50mm dia UPVC Elbow

40mm dia UPVC Elbow

32mm dia UPVC Elbow

25mm dia UPVC Elbow

40mm dia UPVC Hex Nipple

32mm dia UPVC Hex Nipple

25mm dia UPVC Hex Nipple

25x20mm Reducer Elbow

20x15mm Reducer Elbow

40mm dia UPVC Tee

32mm dia UPVC Tee

25mm dia UPVC Tee

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

40mm dia Gate valve

40mm dia Wheel valve

32mm dia Wheel valve

25mm dia Wheel valve

Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap / Swan neck tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Providing Pre construction Anti termite treatment for the building including all chemicals as per standard specifications. Labour charges for preparing the areas for treatment spraying chemicals and other incidential charges etc., complete. The rate shall be inclusive of giving anti-termite treatment to the building for the following four stages including breaking the termite mounds making holes with crow bars at an intervel of 12"to a depth of 8" in the periphery of building and pouring chemicals etc., complete as per ISI 6313-1981 and. The antitermite chemicals used should have 0.5% concentration with 3L solution for the entire operation etc. Stage:1 Spraying Anti-termite treatement chemicals solution for the foundation before laying the foundation concrete bottom and sides of the foundation.

Stage:2 Spraying anti-termite chemicals solution to the grade beams level spraying has to be done for the grade beams brick masonry in the superstructure in contact with back fill earth. Stage:3 Spraying anti-termite chemicals solution on M-Sand for the flooring before laying the flooring concrete. The treatment has to be carried out on the M-Sand filling the basement after leveling operation is over. Stage:4 Spraying anti-termite chemicals solution around the building outside of the building by making crow bar holes at an intervel of 12" to a depth of 8" around the building before laying the plinth projection. This holes has to be be closed after the treatment.

Providing Cup-board Shutter with frame using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work.

Providing and fixing structural glazing fabricated from roll formed sections made of galvanized steel colour coated (Base steel as per IS 513 of ‘D’ quality, galvanized as per IS 277 with Zinc of 120 grams / sqm.) with total coated thickness of 0.72mm. The glass holding section made of 304 grade SS of 0.6mm thick. Galvanized steel sections are to be used as stiffeners inside the colour coated steel / powder coated sections as per the design requirement. Design calculations are made to suit wind pressures as given in IS 875. Paint specifications: Primer coat with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns thick.

Dimensions: The section should be of 37 x 53mm for frame vertical, 37 x 53mm for frame horizontal section and section for reinforcement should be of 31 x 55mm. glass holding section should be of 37 x 37mm for top and bottom grids in between should be of 37 x 18mm. Accessories: Brackets made of CRCA powder coated / electro plated should be used to fix vertical at top and bottom and vertical to slab as per site requirement. Polyurethane brackets should be used to connect horizontal section to vertical sections. Silicone: Natural cure, with good UV resistance to be used. The above frame should be fixed to brick / concrete masonry by using nylon self–expanding cap and driving MS electro plated 80mm long screws into the caps through frames.

Fabrication,Supply,Installation and Handover of 3+mm thick Sintered stone cladding with embedded mesh including all necessary framework. The Sintered Porcelain slabs shall be Supported on Aluminium tube 50X25X1.8mm thick Framing. Our aluminium framing grid size is 500mmX500mm with structural silicone (DC795/995) use to stick the Sintered porcelain slabs to aluminium framework and continuous 3mm VHB tape (12mm width and 3mm thick.) is used for instant adhesion of the Sintered porcelain slab on aluminium frame. Groove 4mmm between the Sintered porcelain slab and these grooves are sealed with weather sealant. The Aluminium frame System shall hold by aluminium angle brackets 50X50X4MM thick every 1 meter c/c with M8X75 SS fasteners for bracket support, SS 304 M8X19 screw used for aluminium framing complete with all other necessary accessories complete complying with standard specification and as directed by the departmental officers.

Supply of cut stone for carrying out Garpagraham, Arthamandapam, Maha Mandapam, Thirumathil and other Temple Structures above 10 feet length upto 14 feet length.

Pillar (Columns)

Supplying and Fixing of Tamil Brass Dye Cast Letters of approved size and colour. The colour treatment process is achieved with MRF colour coat and then the processed coloured layer is set into the kiln for the heat treatment process for the following sizes etc., complete complying with standard specification and as directed by the departmental officers.

Tamil letters of size 25cm

Tamil letters of size 20cm

Supplying and erecting in position of Three phase 5HP Monoblock pumpset with duty of 100lpmx50m, suitable for open well/ sump with ISI mark IS 9079/ 1989 confirming to IS 9079 with 3 phase Panel Board - Star Delta with two level guard and Auto start including Transport charges etc., complete complying with standard specification. The quality and standard of product should be got approved by the Departmental Officers before erecting. Necessary WARRANTY CARD should be produced before erection of Motor.

Labour charges for erection of Motor Pump set in bore well/ open well including fixing and jointing submersible cable with proper clamps up to starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges up to the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, voltmeter, Ammeter, three pilot (indicating) lamps capacitor single phasing preventer, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., complete and testing the pump set and trail run for 10 days.

Providing Rain water harvesting structure with three layers fillter medium 40mm coarse aggregate+ 20mm coarse agg + sand with perfaorated pipe for recharge etc

Drilling of 150mm dia vertical bores in hard rock areas to any required depth as directed by the Departmental Officers including Laboour charges for inserting casing pipes assembling in the drilled including welding thejoints wherever necessary and grouting the casing pipe, and developing the bore etc., the rate shall inclusive of transportations chaargers for the rig and supporting vehicle from one place to another excluding cost of casing pipe etc., complete as directed by the Executive Engineer.

Supply of 160mm PVC casing pipe of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers. The pipe should be got approved by the Executive Engineer before use on works

With Slotted pipe

Without Slotted pipe

Supplying and fixing of suitable PVC end cap (6Kg/cm2) for 6" dia bore well of best quality with ISI mark. (The PVC end cap should be got approved by the departmental officers before execution)

Supplying, Fixing and connecting of 2x32 sq.mm seathed cable wire for the sub-mergible motor from pannel board to sub-mergible pump.

Supplying and fixing of nylon rope for bore well etc,. Complete.

Supplying and fixing 3.00 HP / 3 Phase, 9 Stage sub mergible pump of approved make and quality with ISI mark with necessary accssories and fixed with delivery pipe errected in the borewell with necessary clamp etc., with following additional accssories i) 1 No of 3 Phase Star Delta Starter of 63 AMPS of approved quality and make with ISI mark ii)1 No of 3 Phase 63 AMPS Main Switch of approved quality and make with ISI mark.iii) 1 No of priventor of approved quality and make with ISI mark iv) 1 No of pannel board of required size with indicator fuse unit voltmeter with necessary provision to accomodate the starter and mini starter etc.

Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm – dia with oblique type instantaneous coupling with rotating wheel to open and close the valve including MS flange of table “E”, bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers.

Supply, Installation of Fire fighting application 180 degree swinging type, hose reel drum with 20 mm dia braided thermoplastic hose of 30 meters long so as to extent to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve & open & close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers. Make:OMEX/KARTAR/LIFEGUARD/SAFE GUARD/EQUIVALENT.

Supply, and fixing in position of Fire fighting application Hose of 63mm dia of 15mts length binded by copper wire with 63mm dia Stainless steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the department officers Near every hydrant points including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers. (Make:OMEX/KARTAR/LIFEGUARD/SAFE GUARD/EQUIVALENT.

Supply, and fixing in position of Fire fighting application 63mm dia stainless steel short length Branch Pipe with hexagonal type spray nozzle of 15mm (or) 20mm jet bore. Near every hydrant points including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers.

Supply and Fire fighting application M.S. Hose Box to keep two numbers of Hoses and one number of branch pipes with nozzle. having proper glass window type double door with universe open key, painted inside white and outside PO red. Near every hydrant point including conveyance, all incidental charges, necessary scaffolding and re- doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers. departmental officers.

Supply and fixing in position of Fire Fighting Duct Window having proper glass window type double door with universe open key, painted inside white and outsid post office red for the sizes of 1300 x 900 x 500mm (L x B x D) fabricated using 25 x 3mm MS 'L' Angle and all sides covered with 2mm thick MS sheets, suitable arrangements to kept 2 Nos. of Fire Fighting Hoses and 1 No. Branch Pipe, mounted in fire duct using anchor fasteners, etc., as per standard specifications and as per directed by the Departmental Officers.

Supply and fixing nominal bore quartized bulb type sprinkler bulb 68 Deg C fast response pendent type including GI collar for each sprinkler bulb, mounted in MS pipe line using suitable size MS threaded coupling, thread, Shellac etc.,as per standard methods and including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers.

Supply, erection, testing and commissioning of MS ‘C’ Class heavy duty pipe as per IS 1239,to withstand a developing pressure of 10kg/sq.cm including necessary fittings like MS flange of table ‘E ‘ Elbows, reducers, gaskets, both, nuts with washers & Joints as per standard method of arc welding.Including one coat metal primer and two P.O RED painting including conveyance ,all incidental charges ,necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers.

150 mm dia

100 mm dia

80 mm dia

65 mm dia

50 mm dia

40 mm dia

25 mm dia

Wrapping and coating anti-corrosive treatment for underground MS pipe having one coat of anti-corrosive metal primer ,one layer of Asphalt Tar tape wound over the M.S Pipe as per standard methods as per standard specification as directed by the departmental officers

150 mm dia

100 mm dia

80 mm dia

Supply, erection, testing and commissioning of following sizes heavy duty foot valve including all accessories such as MS flange of table ‘E’ gaskets, bolts &nuts, etc., installed at end of 150/200 mm dia suction pipeline at sump including conveyance ,all incidental charges ,necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers

150mm dia

100 mm dia

Supply ,erection, testing and commissioning of Cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water including necessary MS flange of table ‘E’ gaskets , bolts & nuts including conveyance all incidental charges ,necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers.

150 mm dia

100 mm dia

80 mm dia

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Non-return valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead, tank at terrace level near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312. including conveyance, all incidental charges, necessary scaffolding and re-doing dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers.

150 mm dia

100 mm dia

80 mm dia

Supply, erection, testing and commissioning of Gun metal Gate valve of size 50mm dia including necessary MS flange of table ‘E’ gaskets, blots & nuts, etc. installed at pump house delivery line for the purpose of priming water to suction line including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers.

50 mm dia

Supply and providing 1000 litres capacity Priming Tank made up of PVC. Make: SINTEX / EQUIVALENT

priming tank ( Pump Room)

Priming Tank mounted with the supporting arrangement fabricated using MS angle for the height of 3 metres from the floor level, inlet, outlet, and drain arrangements inside the fire fighting pump room, as directed by the Departmental Officers.

Providing, fixing pipe supports from columns / wall or suspenders from roof slab to suit various dia of pipes made out of GI / MS adjustable rods threaded for a sufficient length to adjust the height of support along with clamping arrangement for holding pipes of anchor fastening, arrangement design of hanger and should confirm with specification.100mm

Supply, Installing, testing and commissioning of Stainless Steel Corrugated Flexible Braided Pipe (Hose) for dropping sprinklers below false ceiling. Pipe shall be 16 bar pressure rating and 1000mm long, 25mm dia with union / reducer, collar, clamps, etc. It shall have UL listed and FM approved.

Supplying and installing of approved type Rosette Plates (Recessed Type in Two Pieces) for sprinklers below false ceiling area. The Rosette shall be fabricated by MS plate of 2mm thick and the finish shall be powder coated and colour, as directed by the Departmental Officers.

Supply and laying of following sizes of Armoured Aluminium Cables for electrical motor, control panel, pressure switch, jockey motor etc.. The rate inclusive of all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: POLYCAB / PARACON / FINOLEX / EQUIVALENT.

3 core 10 sqmm armoured copper cable (Pump Room)

2 core 2.5 sqmm armoured copper cable (Pump Room)

Supply and laying of following sizes of Armoured Aluminium/Copper Cables for electrical motor, control panel, pressure switch, jockey motor etc., all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: POLYCAB / PARACON / FINOLEX / EQUIVALENT.

10 core 2.5 sqmm armoured copper cable (Pump Room)

Earthing arrangements with GI earth plate including charcoal and salt with necessary excavation in all soils and to full depth as may be required and masonry work. Refilling the sides of foundation with excavated earth as per the standard specification and as directed by the department officers.

Earthing Arrangements

Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14 kg. range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: H-GURU / ISI MAKE / EQUIVALENT.

Pressure Gauge

Supply, erection, testing and commissioning of suitable Pressure switch of reputed make line indfoss or Donfoss including necessary values, couplings etc. connected with electrical main control panel and setup at proper differential so as to auto start & auto stop the electrical motor. Jokey motor including conveyance. all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary metering protections & indications complete as per standard specification and as directed by the departmental officers.

Pressure Switch

Main Control Panel (Pump Room)

Supply erection testing and commissioning of fire fighting application horizontal centrifugal type pump rated for 2280 LPM at 70 mtrs head with electrical motor of 60 HP of 415V,3 phase connection, complete with base plate and accessories. (Make: Kriloskar or Equivalent).The rate is inclusive of necessary vibration bed mounting, etc as per standard method as directed by departmental officers.

Electric motor driven fire pump set (Pump Room)

Supply, Installation, Testing and commissioning of Diesel engine driven main Fire Pump suitable for automatic operation and consisting of following complete in all respects as required. (a) 1 No. Horizontal split Casing centrifugal type fire pump capable of delivering 2280 LPM against a total head of 70 mtrs so as to ensure a minimum pressure of 3.5 Kg per sq cm at the farthest top most hydrant/ Outlet with pump casing of cast iron to grade FG 200, IS 1520 and parts like Impeller, shaft sleeve, bearing ring etc of non-corrosive metal either like Bronze, brass or Gun Metal and shaft stainless steel. b) 68 BHP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant BS & IS standard complete. c) Auto starting mechanism, 12 volts 24 volts electric starting equipment like self Motor, Dynamo, Solenoid switches etc. d) 110 ltrs capacity Diesel tank mounted over stand fabricated using 25mmx25mmx6mm size MS angle, providing with level indicator, inlet port, outlet port, drain port and diesel return line port and fuel pre filter etc.

e) exhaust system having flexible metallic muffler, 100mm dia MS heavy pipe extended upto 1m. Outside pump house duly insulated with 50mm thick glass wool with 1.00mm thick aluminium sheet cladding, residential silencer with necessary MS support arrangements from wall or ceiling as per site condition. f) Dash Board consisting the Instruments like Temperature Gauge, Galvano type DC Ammeter, Lub oil Pressure Gauge, Ignition switch, Emergency Stop and all other protection equipment as per specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc as required. g) 12 V / 24 V, storage battery, maintenance free tape, 180 AH rating. h) M.S fabricated common base plate, Coupling guard, foundation bolts etc as required. i) Positioning the Diesel Engine driven Fire Pump over cement concrete foundation using suitable size Anti Vibration mounting arrangements. All works including conveying, fixing and incidental charges etc complete as per standard specification and as directed by the departmental officers. Make: KIRLOSKAR/ EQUIVALENT

Diesel engine driven main Fire Pump (Pump room)

Supply, erection, testing and commissioning Mono Block type Fire Fighting Pressurisation Pump of 180 LPM 110 metres head at 10 HP with suitable base frame including necessary vibration bad mounting etc., including conveying, fixing and incidental charges., etc., complete as per standard specification and as directed by the Departmental Officers. (Make: Kirloskar / Equivalent)

Diesel engine driven main Fire Pump (Pump room)

Supply, erection, testing and commissioning of fire fighting application monoblock motor pumpset of 900 LPM at 40 metres head to develop 3.5 kg/sq.cm at the heightest and farthest hydrant point to make 30 m water jet at the time of fire fighting emergency cicumstances, coupled with 11 KW / 15 HP rated three phase 414 volts, 50 Hz, 2880 rpm electrical motor the pump with cast ron body, bronze impeller, rope gland packaging, suction size of 80 mm dia. delivery size of 65 mm dia., including the cost of foundaton concrete anti vibration mounting, rain safety hood and etc. complete as directed by the Departmental Officers (Kirloskar make KDS 1555+ or Equivalent)

Supply, erection, testing and commissioning of Fire fighting 4 way fire brigade inlet with necessary Gun metal 63 mm dia non return spring shutter arrangements so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry, including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers.

4 way fire brigade inlet (Yard - Entrance)

Supply and fixing in position of 12 Volt 180 AH Lead Acid, Sealed Maintenance Free (SMF) batteries with connecting leads, lugs terminal post, etc., as per standard methods and including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT.

Supply, erection , testing and commissioning of Air release valve of 20mm dia so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers.

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) powder type Fire Extinguisher of 6 kgs capacity as per IS: 15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc complete as per standard specification and as directed by the departmental officers.

Supply, installation, testing and commissioning of Micro Processor based conventional 12 Zone Fire Alarm Control Panel having the rating of 24 volt DC power supply, consisting 230 / 24 volt SMPS unit, 2 Nos. of 12 volt 7 AH standby batteries, suitably mounted on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers.

Supply, installation, testing and commissioning of Conventional Smoke Detector suitably mounted on ceiling with MS juction box / false ceiling using fixing accessories ike screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers. (Make: Apollo / Equivalent)

Supply, installation, testing and commissioning of Manual Call Point (MCP) providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers. (Make: Ravel / Equivalent)

Supply, installation, testing and commissioning of Electronic Hooter / Sounder providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers (Make: Ravel / Equivalent)

Supply and laying of FRLS PVC insulated 2 core 1.5 sq.mm. Armoured Copper Cable on ceiling / wall using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers.

Supply and laying of 4 core 10 sq.mm. armoured copper cable for power wiring to the Terrace Pump Motor with runs of 14 SWG TC wire for earthing, providing in wall with suitable size GI clamps, screws, wooden plug, end termination by using suitable size cable glands, copper sockets and etc., as directed by the Departmental Officers.

Supply and laying of 2 core 1.5 sq.mm. armoured copper cable for control wiring to the Terrace Pump Motor with runs of 14 SWG TC wire for earthing, providing in wall with suitable size GI clamps, screws, wooden plug, end termination by using suitable size cable glands, copper sockets and etc., as directed by the Departmental Officers.

Supply & Installation of Gun Metal Ball Valve of size 25mm dia size including necessary Fittings

3c x 35Sqmm Aluminum Armoured Cable for Main Electrical Pump

Supply & Installation of in position the sign board of "EXIT " with arraow to be placed at walking pathways by fixing on walls to direct occupants to outside the buliding in an emergency. The Exit sign board will be autoglow photoluminiscent type which will glow at dark.(Single Side indication)

Supply & Installation of Fire Escape Route Plan Laminated Board Auto Glow Print to be placed at each floor by fixing on walls to direct occupants to outside the buliding in an emergency. The Fire Escape Route Plan will be autoglow photoluminiscent type which will glow at dark.(Single Side indication)

Supplying and fixing conference type public address system, projector and motorized screen-Higher end etc., complete complying with standard specifications and as directed by the departmental officers.

Wall speaker 15W

PA Mixer Amplifier 120W

Cordless mic UHF

Supplying and erecting in position of 250 liters capacity Industrial Model Reverse Osmosis Water-cum- Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact.

Supply, Installation & Providing of Tip-up recliner chair of center to center 533mm,1020mm height, Plywood (hardwood) with induction heating and high pressure pressed. ABS moulded housing for seat & back cushions,armrest made of PP/PPCP/ABS or semi rigid PU foam. Polyurethane injection moulded flexible foam seat and back density 50 – 55 kg/m3, Fabric to be 100% polyester synthetic fabric with 4 mm polyurethane foam lamination.Fire retardant standard ISO3795, FMVVSS302, Water repellent - Standard -AATCC193. Torsion spring/spring steel IS:4454 1981 Grade III. HRCA/CRCA Sheet metal IS:1079 1994, Electrostatic epoxy powder coating thickness:70 - 80 microns. Seat numbering at side of the chair with LED lights on sides along with aisles.The chairs should be installed to the flooring with the anchor fasteners 12mmx100mm pin type. Fabric colour to customer choice etc., complete

Making up Clay models of cave temple Landscape. The mold is taken in Plaster of Praise Material over the formed Figer. The place where the mold is taken is filled with 2-layer fiberglass material and then the model is made with a thickness of 4mm. The model will be Rubbed with Fine Sand Paper. The model is Clean washed with Soap oil, and Painted with 1 Coat of Duco Primer. The Model is Painted with an Acrylic multi-color paint finish with a spray gun and the Artist's Manual work. Water Effect provide in Epoxy Resin Materials. 3-D printing technique shall be used as required in the model. Make a Leaves in Fabric Cloth Materials by Manual and Stencil Cut. Provide Fabric Dye Colours in Leaves, and Acrylic multi-paint finish with a spray gun. Leaves are arranged by Manual Work.The Rate included Material, Model Maker Charges, Transportation, Fixing, and Labor Charge Ext., Complete. Size - 7' x 4' x 12 Inch height

Making up Clay models of Gopuram, Statues, and Pillars. The mold is taken in Plaster of Praise Material over the formed Figer. The place where the mold is taken is filled with 2-layer fiberglass material and then the model is made with a thickness of 4mm. The model will be Rubbed with Fine Sand Paper. The model is Clean washed with Soap oil, and Painted with 1 Coat of Duco Primer. The Model is Painted with an Acrylic multi-color paint finish with a spray gun and the Artist's Manual work. The water Effect is provided in Epoxy Resin Materials. 3-D printing techniques shall be used as required in the model. Other materials including metal, wooden plastic boards, foam boards, acrylic sheets, cardboard, sponges, etc. shall be used as needed for the model. Provide LED Lights in the Model. The Rate included Material, Model Maker Charges, Transportation, Fixing, and Labor Charge Ext., Complete. Size - 7' x 4' x 12 Inch height

New 3D Mural Panel to Display Museum Artifacts in Thiruvannamalai District. Making up Clay models. The mold is taken in Plaster of Praise Material over the formed Figer. The place where the mold is taken is filled with 2-layer fiberglass material and then the model is made with a thickness of 4mm. The embossed figure is approximately 8 inches. The model will be Rubbed with Fine Sand Paper. The model is Clean washed with Soap oil, and Painted with 1 Coat of Duco Primer. The Model is Painted with an Acrylic multi-color paint finish with a spray gun and the Artist's Manual work. Provide All over 4 side 3-inch Carnish Boarder in the Panel. Bakside the panel Provide 12mm plywood. The Rate included Material, Model Maker Charges, Transportation, Fixing, and Labor Charge Ext., Complete. Size — 6’ x 3' - 18' x 2 NO

Providing and fixing of Digitally Printed Retro Reflectorized Overhead Gantry Informatory sign Board made of cube corner Micro Prismatic grade sheeting conforming to Type XI standards of IRC 67 - 2022 and ASTMD4956 – 09, specification and fixed over 2mm thick aluminum sheet fixed on back supporting frame mild steel L angle of size 50mm x 50mm x 6mm. The Vertical support post for the installation of overhead sign Gantry shall be made of 300NB (Nominal Bore) MS Pipe with 12mm thick with a ground clearance of 6 meters along with 80NB (Nominal Bore) MS Pipe with 4mm thick and 40NB (Nominal Bore) MS Pipe with 3.20mm thick support posts. MS Base plate of size 1200mm x 1200mm x 25mm and MS Top plate of size 900mm x 1650mm x 16mm to be used to hold the sign board at the top and bottom respectively. MS Stiffener plates 8mm thick of sizes 420x420, 682x420, 288x288, 288x927 & 44x130 are to be used. Anchor bolts of dimension 25mm dia and 1000mm length are to be used as fixtures.

The approved direction information should be digitally printed and should have 70% of the co-efficient of Retroreflection values against the values as mentioned in Table 6.9 of IRC 67 – 2022. The Latex printer used for digital printing should use inks with low VOC emissions and have green guard, eco logo certificates as per UL 2801 standards. The retro-reflective sheeting shall be covered under 10 years warranty issued for field performance and a certified copy of three years Outdoor exposure report shall be obtained as per IRC 67-2022 (As per MoRT&H specification No.801). Cantilever sign shall be installed at the site as per the approved structural and foundation drawing provided in the tender document and including cost and conveyance of all materials, equipment, machineries to worksite, including all labour charges for fixing the gantry in position with all leads and lifts, loading charges and necessary for satisfactory completion of the work as directed by the engineer-in-charge etc., complete. of size 12.00 m X 1.8 m

Providing and fixing of Digitally Printed Retro Reflectorized Overhead Cantilever Informatory sign Board of Size 5.00m x 1.80m made of cube corner Micro Prismatic grade sheeting conforming to Type XI standards of IRC 67 - 2022 and ASTMD4956 – 09, specification and fixed over 2mm thick aluminum sheet fixed on back supporting frame mild steel L angle of size 50mm x 50mm x 6mm. The Vertical support post for the installation of overhead sign Gantry shall be made of 300NB (Nominal Bore) MS Pipe with 12mm thick with a ground clearance of 6 meters along with 80NB (Nominal Bore) MS Pipe with 4mm thick and 40NB (Nominal Bore) MS Pipe with 3.20mm thick support posts. MS Base plate of size 1200mm x 1200mm x 25mm and MS Top plate of size 900mm x 1650mm x 16mm to be used to hold the sign board at the top and bottom respectively. MS Stiffener plates 8mm thick of sizes 420x420, 682x420, 288x288, 288x927 & 44x130 are to be used. Anchor bolts of dimension 25mm dia and 1000mm length are to be used as fixtures.

The approved direction information should be digitally printed and should have 70% of the co-efficient of Retro-reflection values against the values as mentioned in Table 6.9 of IRC 67 – 2022. The Latex printer used for digital printing should use inks with low VOC emissions and have green guard, eco logo certificates as per UL 2801 standards. The retro-reflective sheeting shall be covered under 10 years warranty issued for field performance and a certified copy of three years Outdoor exposure report shall be obtained as per IRC 67-2022 (As per MoRT&H specification No.801).Cantilever sign shall be installed at the site as per the approved structural and foundation drawing provided in the tender document and including cost and conveyance of all materials, equipment, machineries to worksite, including all labour charges for fixing the gantry in position with all leads and lifts, loading charges and necessary for satisfactory completion of the work as directed by the engineer-in-charge etc., complete.

Providing and fixing of Digitally Printed Retro Reflectorized Sign Board using UV Inkjet Printer made out of cube corner micro prismatic grade sheeting of Type-XI standards of IRC 67-2022 and ASTM D 4956 – 09 specification, Digitally Printed using UV Inkjet Printer (UVIJ) for traffic colour, images/ logos/ text and laminated with clear electro- cuttable film and applied to properly prepared sign substrates, fixed over 2mm Aluminium sheet with back supporting frame of 50x50x6mm Mild Steel ‘L’ angle and supported on a 150NB (Nominal Bore) pipe with 4.50mm thick with an overall height from top of the board to foundation. The sign board should be of 2.10m clear height from the ground level to the bottom of the sign board and 1.10m below ground level.

The sign post should be painted as per IRC 67-2022 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete of size 450x 450 x 1100mm including cost and conveyance of all materials, equipment, machineries to worksite, including all labour charges for fixing the gantry in position with all leads and lifts, loading charges and necessary for satisfactory completion of the work as directed by the engineer-in-charge etc., complete. The Micro prismatic sheeting should have minimum 70% coefficient of Retro-reflection values as per table 6.90 of IRC 67-2022. The retro- reflective sheeting shall be covered under 10 Years warranty issued for field performance and a certified copy of 3 years outdoor exposure report shall be obtained as per IRC 67-2022. The warranty shall be inclusive of digitally printed images/ logos/ test/ legends and their bonding to the retro-reflective sheeting (as per MoRT&H specification no.801) of Size – 3.64m x 2.42m

ELECTRICAL WORKS

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) ( 4 points /Coil) Higher End

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End

Supply and fixing of 40W UNECO Fixed Cob Downlight Fitting with LED Round type Recessed fitting with LED ( Make : UNECOFIXDLR40WLED857S60-G2 Havells / Equivalent ) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 2'x2' 40w LED 4000K Square type Recessed fitting with Complete and PVC unsheathed Copper leads from terminals to the fitting ( Make :VENUSTREND2X2 PLR40W LED857SWH Havells / Equivalent )

Supply and fixing of 20 W 4 Feet LED fitting complete with TW round blocks on wall or ceiling with with PVC unsheathed Copper leads from terminals to the fitting (Higher End).

Supply and fixing of 2 x 22W 4 Feet LED Fitting with 20W LED Tube Light for T8 Fitting (Single Side) with TW round blocks on wall or ceiling with PVC unsheathed copper leads from terminals to the fitting with LED tube (Higher End).

Supply and fixing of polycab Superia / Equivalent SP02 Star Rated Premium BLDC 1200mm Ceiling Fan for home with Remote | Clip-On Underlights, 100% Copper, Energy Saving complete with 3mtr down rod on the existing fan clamp.

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan

Supply and fixing of WT bulk head fitting with guard suitable for 15 W LED Bulb

Supply and fixing of Smartway / Equivalent 26W Beverly LED Ceiling Light | Modern Decorative | Natural White Focused Light | Bedroom, Living Room, Dining, Office(track light)

Supply and fixing of Grace Fountain Chantlier 9LS E14 Black on ceiling suspended with PVC unsheathed leads from terminals to the fitting ( Make: LHFHCHCBTE1K005 Grace Chandelier Grace Fountain Chandelier 9LS E14 Black Havells / Equivalent.

Supply and fixing of 30W Uneco Laser Linear LED Ceiling Light | Modern Decorative | Natural White Focused Light | Bedroom, Living Room, Dining, Office (Haveels / Equivalent).

Supply and fixing of Architectural street light post with following dimensions : Height 20 (Feet) Pole Section 139X114X88.9,Arm - 1500 MS base plate duly welded at the bottom with concerting with construction of Masonary pedestal with suitable MS box to house the 10A DP MCB two way connector on suitable hylem sheet and supply and fixing of Decorative Type 60W Street light fitting (Make : T-lite ) complete with necessary cowl arrangements on the above post and coil earthing with PVC unsheathed leads with painting of suitable colour ( Make : T-Lite /K lite / Equivalent).

Supply and fixing of 4 pole sheet enclosure with 63A FP MCB in flush with wall with earth connection The MCB DB and MCB's should be Legrand/ Hage make (Higher End).

Supply and fixing of 3nos.6A two module 5 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections (Higher End).

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections (Higher End).

Supply and fixing of 60W LED street light fitting with LED with 32mm dia. GI pipe (class B) with 1no.32 mm dia GI bend complete on the existing post/ on wall with PVC unsheathed FRLS copper leads with MS clamps and with painting

Copper plate Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 600mm x 600mm x 3mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and fixing of 200 A Three phase 500V 4 Pole Change over Switch on suitable angle iron frame work with MS cable entry boxes with earth connection only.

Supply and fixing of 20A Flush type Wall Socket 32A DP MCB completeset for AC Plug in flush with wall with earth connection (For AC Plug)

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB as incoming and 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 7 segment 6 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 63A 4 pole incoming MCB and another seperate 4 way provision for accomodating 1 No 63A 4P 30MA RCCB/ELCB and 3 Nos 63A DP MCB Isolator as sub incomers and seperate provision for 18 Nos 6A to 32A SP MCB for outgoing in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only.

Supply and fixing of 4 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board (with MCCB incomer) with IP 43 Protection double door (metal door) with 1 no. 125A 4P MCCB switch as incoming and 4 nos. 63A 3P MCB as outgoing with suitable cable end box in flush with wall with earth connection only (Higher End).

Supply and fixing of 6 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board ( with MCCB incomer) with double door (metal door) with 1 No 160A 4P MCCB as incoming and 4 Nos 63A 3P MCB, 6 Nos 6A to 32A SP MCB as outgoing with suitable cable end box in flush with wall with Earth connection only (Higher End).

Supply and run of 2 of 4sq.mm. PVC in sulated SC unsheathed FRLS copper conductorof 1100V grade insuitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 4sq.mm copper wire and mak in good of the concealed portion with suitable colour (For 5A -3Nos ,15A plug ,3 nos 15A and AC box)

Supply and run of 2 of 6sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade insuitable PVC rigid pipe concealed in wall and ceiling with contiinuous earth wire connection of 6sq.mm copper wire and making good of the concealed portion with suitable colour (for LDB)

Supply and Run of 4 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigd pipe on wall and ceiling with continuous earth wire connection of 10 sq.mm copper wire with painting of suitable colour.

Supply and Run of 4 of 25 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in 50mm PVC rigd pipe on wall and ceiling with continuous earth wire connection of 25 sq.mm copper wire with painting of suitable colour.

Supply and clarnping of 31/2 x 95 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps.

Supply and fixing of brass cable gland for 3-1/2 x 95 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 95 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete .

Supply and clarnping of 3-1/2 x 120 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps .

Supply and fixing of brass cable gland for 3-1/2 x 120 sq.mm. PVC LTUG aluminium armoured cable with earth connection .

Supply and providing cable end termination of 3-1/2 x 120 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and Laying of 4 x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clarnping of 4 x 16 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of 32A TPNMC switch on suitable angle iron frame work with MS cable entry box with earth connection only

Supply and fixing of 5Mtr LED FLEXI STRIP(Modal:FLEXISTRIP5 MIP2024V/ 2ALED865MOD V1) with CVDRIVER24V2A ( Make : Havells / Equivalent ) with optimum brightness & uniformity of light for perfect cove lighting.

Supply and fixing of 50W Gate light Fitting (CORALMAXIPT50WLED757PSYMTOPC MAKE: HAVELLS / Equivalent ) with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of 5KVA automatic Inverter with input voltage 180V - 260V and output voltage 200V - 230V 50Hz with 18 nos 12V 100AH tubular battery and testing complete with connection. (Make: Exide / Equivalent).

Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in rigid pipe concealed in wall and ceiling with making good of the concealed portion with suitable colour (For UPS)

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply and run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall and ceiling for earth connection

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection

Supply and erection of 200 Amps Capacity dust and vermin proof floor mounting cubical panel board of Size 7'x4.5'x1' fabricated out of 16 SWG MS sheet for outer body, stiffness and doors and with supply and fixing of following interior switches with Horizontal bus bar chamber and Switches Fixced on the tob and bottom of the bus bar chember with cable adopter chamber of the extreme wnd of one side with two coats of quality paint over one coat of zinc oxide primer superscription of incoming and outgoing feeding cable details, capacity of switches etc., with white paint and 2 nos metallic danger board affixed complete on base channel supports to satisfy the latest CEIG rules with the following switches

1] 200A FP switch disconnector fuse interior only with HRC fuses double break - 1Nos [L & T / Siemens] (1 no- incoming

2]160 A TPN switch disconnector fuse interior only with HRC fuses double break-6Nos [L & T / Siemens].

Spilt AC arrangements

Supply and erection of Indoor units of 2.0 Ton capacity (3 Star Rated) Split type Airconditioner unit confirming to ISI 1301 (Part-2) 1992 with amendment No.1 fitted with Hermetically sealed compressor operation on 230 V 50Hz AC Supply system with energy efficient operating system with refrigerant gas R-22 suitable for high wall mounting evaporator and specification as under general requirement interconnection of pipes and cables. (Make : Blue Star, Carrier, Voltas / Equivalent).

Supply and erection of 5 KVA Capacity Automatic voltage stabilizer suitable to operation on 230 Volts, single phase, 50Hz, AC supply system with time delay relay and High/Low voltage cut off, input voltage range 170V to 270V single phase, wall mounting type stabilizer with necessary clamp.. (Make : V-Guard)

Supply and laying of 5/8" and 3/8" Copper Pipe (Extra beyond 3 metres supplied with AC unit .

Supply and fixing of water drain pipe line (1" PVC pipe).

Supply and fixing of Ms stand for fixing outdoor unit.

DUCT AC

FOR DUCT:Supply 5.5 TR norminal capacity ceiling suspended ductable air conditioner with the following components. 5.5 TR capacity ceiling suspended Ductable Air conditioner high tech,low height,low noice level indoor unit with fin and tube type cooling coil,Detachable type drier provided in refrigerant cicuit to reduce moisture content multi stage type distributor for feeding equal quantities of the refrigerant mixture to all the section of the coil,with required valves,directly coupled blower to reduce troubles and wear & tear compared to belt drive blower.Thermostatic expansion valve lift and pull type aluminum framed durable,washable air filter.Integrated electrical panel with complete microprocessor control with display for easy operation and maintenance of unit common operating conditions of 45 F suction temperature Auto reset type HP/LP safety cut to improve reliability of compressor.(At stage)

Supply of 5.5 TR capacity ceiling suspended ductable air conditioner high tech Outdoor unit with power saving high efficiency sturdy and rugged 1 No of scroll comprssor for each circuit with inbuilt internal thermal protector,internal pressure relief valve,Auto reset type HP/LP safety cut out to improve reliability of compressor and condenser shell be made of super slit high efficient aluminum fins mechanically banded to copper tubes condenser 'L' type coil to be rigidly fixed to unit frame with fasteners.imported condenser fan & fan blades to be statically and dynamically balanced to reduce noise and vibration.The fans are direct driven 3 or single phase motor with protection.Condencing temperature 130' F for the system operations.

FOR DUCT:Supply 8.5 TR norminal capacity ceiling suspended ductable air conditioner with the following components. 8.5 TR capacity ceiling suspended Ductable Air conditioner high tech,low height,low noice level indoor unit with fin and tube type cooling coil,Detachable type drier provided in refrigerant cicuit to reduce moisture content multi stage type distributor for feeding equal quantities of the refrigerant mixture to all the section of the coil,with required valves,

directly coupled blower to reduce troubles and wear & tear compared to belt drive blower.Thermostatic expansion valve lift and pull type aluminum framed durable,washable air filter.Integrated electrical panel with complete microprocessor control with display for easy operation and maintenance of unit common operating conditions of 45 F suction temperature Auto reset type HP/LP safety cut to improve reliability of compressor.(At stage)

Supply of 8.5 TR capacity ceiling suspended ductable air conditioner high tech Outdoor unit with power saving high efficiency sturdy and rugged 1 No of scroll comprssor for each circuit with inbuilt internal thermal protector,internal pressure relief valve,Auto reset type HP/LP safety cut out to improve reliability of compressor and condenser shell be made of super slit high efficient aluminum fins mechanically banded to copper tubes condenser 'L' type coil to be rigidly fixed to unit frame with fasteners.imported condenser fan & fan blades to be statically and dynamically balanced to reduce noise and vibration.The fans are direct driven 3 or single phase motor with protection.Condencing temperature 130' F for the system operations.

FOR DUCT:Supply 11 TR norminal capacity ceiling suspended ductable air conditioner with the following components. 11 TR capacity ceiling suspended Ductable Air conditioner high tech,low height,low noice level indoor unit with fin and tube type cooling coil,Detachable type drier provided in refrigerant cicuit to reduce moisture content multi stage type distributor for feeding equal quantities of the refrigerant mixture to all the section of the coil,with required valves,directly coupled blower to reduce troubles and wear & tear compared to belt drive blower.Thermostatic expansion valve lift and pull type aluminum framed durable,washable air filter.Integrated electrical panel with complete microprocessor control with display for easy operation and maintenance of unit common operating conditions of 45 F suction temperature Auto reset type HP/LP safety cut to improve reliability of compressor.(At stage)

Supply of 11 TR capacity ceiling suspended ductable air conditioner high tech Outdoor unit with power saving high efficiency sturdy and rugged 1 No of scroll comprssor for each circuit with inbuilt internal thermal protector,internal pressure relief valve,Auto reset type HP/LP safety cut out to improve reliability of compressor and condenser shell be made of super slit high efficient aluminum fins mechanically banded to copper tubes condenser 'L' type coil to be rigidly fixed to unit frame with fasteners.imported condenser fan & fan blades to be statically and dynamically balanced to reduce noise and vibration.The fans are direct driven 3 or single phase motor with protection.Condencing temperature 130' F for the system operations.

FOR DUCT:Supply 25 TR norminal capacity ceiling suspended ductable air conditioner with the following components. 25 TR capacity ceiling suspended Ductable Air conditioner high tech,low height,low noice level indoor unit with fin and tube type cooling coil,Detachable type drier provided in refrigerant cicuit to reduce moisture content multi stage type distributor for feeding equal quantities of the refrigerant mixture to all the section of the coil,

with required valves,directly coupled blower to reduce troubles and wear & tear compared to belt drive blower.Thermostatic expansion valve lift and pull type aluminum framed durable,washable air filter.Integrated electrical panel with complete microprocessor control with display for easy operation and maintenance of unit common operating conditions of 45 F suction temperature Auto reset type HP/LP safety cut to improve reliability of compressor.(At stage)

Supply of 25 TR capacity ceiling suspended ductable air conditioner high tech Outdoor unit with power saving high efficiency sturdy and rugged 1 No of scroll comprssor for each circuit with inbuilt internal thermal protector,internal pressure relief valve,Auto reset type HP/LP safety cut out to improve reliability of compressor and condenser shell be made of super slit high efficient aluminum fins mechanically banded to copper tubes condenser 'L' type coil to be rigidly fixed to unit frame with fasteners.imported condenser fan & fan blades to be statically and dynamically balanced to reduce noise and vibration.The fans are direct driven 3 or single phase motor with protection.Condencing temperature 130' F for the system operations.

Supply and filling of R-22 Refrigerant gas.

Supply and fixing of suitable MS angle frame for mounting the Indoor units.

Supply and fixing of suitable MS angle frame for mounting the Outdoor units.

Supply and fixing of hard drawn cooper refrigerant piping of 5/8" dia, inter connecting indoor and oudoor units with necessary fittings,supports etc

Supply and fixing of hard drawn cooper refrigerant piping of 7/8" dia,inter connecting indoor and oudoor units with necessary fittings,supports etc.

Supply and fixing of flexible canvas connection between indoor unit and ducting

Supply,Fabrication and erection of fabricated ducting made up of 24 Gauge thickness

Supply and fixing of extruded aluminum powder coated supply and return air grilles with volume control damper

Supply and fixing of water drain pipe line (1" PVC Pipe)

Supply and Providing of insulation for copper refrigerant piping and water drain pipe line

Supply and fixing of Duct mouth Dampers

Supply and providing acoustic for initial portion of ducting with 12mm thick fiber glass rigid board covered with tissue paper and aluminum perforated sheet

Supply and providing thermal insulation of 9mm thick vidoflex with aluminium foil.

Supply and providing Civil concrete block for mounting the airconditioning unit

Supply and providing of power supply for indoor to outdoor unit motors for 10Sq mm copper flexible single cable

Supply and providing of control supply for indoor to outdoor unit Hp and Lp cut outs for 1.5Sq mm copper flexible cable

Supply and providing of signal cable for indoor to outdoor unit sensor controls for 0.5Sq mm 4 core flexible signal cable

20 PERSON PASSENGER LIFT

Design, Engineering, Fabrication, Supply, Erection, Testing, Commissioning and Handing over of 1No 20 Persons Passenger Lift as per following technical specifications which includes all taxes and duties.(without Machine room -MRL ) Technical Specifications: Location: Museum in Tiruvannamalai 1. No of lift: One No. 2. Type of lift: Passengers Lift (Geared) 3. Capacity of lift: 20 Persons (1360 Kgs) 4. Speed: 1.50mtr / sec 5. Type of drive: Microprocessor based specific variable voltage variable frequency (V3F) drive with enhanced ride comfort and near zero leveling functions. 6. No of floors: Ground+1 floors.

7. Total travel: 12Mts Servicing Ground+1 floor 2stops, 2 levels & 1 opening. 8. Leveling accuracy: High level accuracy with smooth and jerk free stopping. 9. Construction of Car: Special car made of stainless steel hairline finish panels complete with single tile false ceiling with direct LED lighting, tubular handrail, 300mm sweep fan, stretcher impact guard at all three side to prevent the SS damages and for better aesthetics. 10. Position of machine: Directly above the lift well. 11. No of Car entrance – Side opening door with stainless steel No.4 finish with full height infra red door sensor. 12. No of Landing entrance: Side opening door with stainless steel No.4 finish complete with SS frames.(SS 304 grade) 13. No of Entrance: One in front only. 14. Car size:2000 mm wide x 1550 mm deep x1600mm height. Clear opening: 1000mmX2000mm height

15. Lift well size :2700 mm wide x 2400mm (existing)deep RCC construction with brick masonry . 16. Lift pit depth :1600 mm 17. Power supply: 415V, Three phase and 230 V 50 Hz single phase AC supply for light. 18. Control: Micro computer based full- collective logic system with / without attendant mode. 19. Car Indicator: Digital 7 segment 1.1mm Height direction & position indicator with height intensity indication in Red color. 20. Landing Indicator: Digital 7 segment 1.1mm Height direction & position indicator with height intensity indication in Red color 21. Emergency alarm bell: Battery operated alarm bell to be provided with automatic charging .

22. Emergency light: Battery operated light to be provided with automatic charging device. 23. Fire man’s switch: To be provided at ground floor. 24. Minor builders work: To be provided by lift contractor. 25. Scaffoldings: To be provided by lift contractor. 26. Steel for lift machinery: To be provided by lift contractor. 27. Stainless steel sill angles and facial plates: To be provided by lift contractor.

28. Servicing and maintenance: Free comprehensive servicing and maintenance should be provided by lift contractor during the guarantee period of one year. 29. Automatic Rescue Device: To facilitate the landing of the nearest floor at the time of power failure. This shall consist of suitable type battery system with charger, inverter under voltage protection system etc. 30. Lift license: Preparation of drawing, payment of charges to CEIG and insurance policy and obtaining CEIG safety certificate as per lift act should be done by the lift contractor. 31. Floor annunciate with music 32. Special features a) Inverter based battery operated emergency light & alarm bell. b) Stainless steel signal fixtures. c) Aluminum checkered plate flooring. d) Call Registering Type Micro push button.

e) Automatic rescue device. f) Full Collective Logic control g) PCB control push button h) Separate fan switch in the car i) Constant voltage Transformer for control system. j) In built brake release lever k) Pit ladder l) Stretcher impact guard at all three side m) Intercom n) Load weighing device o) Lift floor announcement p) Minor civil works q) Scaffolding,r) Obtaining Lift License 33.Special features to be added in the Lifts for people with wide range of abilities should be as per annexure I enclosed.

34. Over speed governor, phase failure and phase reversal relay, alarm bell, T guide brackets for car and counter weight. Rubber padding under winding unit. Motor of adequate capacity electromagnetic brake with compression springs, car safety gears, buffers, electro mechanical door locks. Emergency key, side supporting angles, motor over load protection devices, final limit switch, main suspension ropes, counter weights etc,. 35. Guarantee: Guarantee for the materials & workmanship of equipments complete should be offered by the lift firm for a period of not less than one year. 36. Site testing in accordance with IS 14665 should be carried out at the time of handing over. (Make: Johnson/Kone/OTIS/ Equivalent). 37. Two hour fire rated doors. 38. All diffferently abled features are included as per Differently Abled Act.

Supply and erection of 30 KVA Three phase Microprocessor controled air cooled unbalanced electronic servo stabilizer with High / Low Voltage Cut off and Single phase preventer with built in Manual Bypass arrangements . Like MakeMATRIXmx Model :MPLASS 4500,Input Volts 290v-– 470v

, Output volts - 400v, voltage regulation ± 1%, output volt adjust 395v-405v, input frequency 47hz– 52hz, output frequency 50hz ± . 5%, voltage correction 40v / sec, controll circuits fully micro processor controlled Digital controlled advanced circuit boards, lcd display , input voltage reading

, Output voltage reading , frequency reading, 3phase voltage reading, load current reading, r,y,b input indicator , l.e.d indicator for inupt on/ output on, low voltage /highvoltage trip, mccb for overload / short circuit protection, overload trip, builtin manual bypass arrangement (for lift)

Supply and fixing of 63A TPNMC switch on suitable angle iron frame work with MS cable entry box with PWD earthing. (For Lift)

160 KVA DG

Supply, erection, commissioning, testing and handing over of 1No 160 KVA (128 Kw) Diesel Generator Set with acoustic enclosure conforming to CPCB IV+ Norms and BIS Specifications canopy, fuel tank battery charging alternator with Standard Panels developing 3phase electrical output 160 KVA powered by diesel engine of 0.8P.F Three phase 415/420Volts, 50c/s, 115BHP at 1500RPM as detailed below.

a]. ENGINE: odel 6SL 8800 TA turbo charged vertical inline 6 cylinders. Liquid cooled diesel engine developing 200 HP at 1500 RPM conforming B.S 5514 / 6490 or IS 10000 incorporating the following accessories.

The engine shall comprise the following standard fittings Flexible coupling with guard, Flywheel, Air cleaner, Fan blower type with guard, Radiator with guard, water pump engine mounted, Fuel pump, Fuel filter , Lubrication oil filter, Lubrication oil pump, Governor (mechanical/hydraulic) Exhaust silencer residential type.

b]. Electric starting equipment, complete with starter motor, dynamo and battery with cables, flexible exhaust piping of 50cms length

c].ENGINE INSTRUMENT PANEL MOUNTED: Starting push button with key, lubricating oil temperature gauge, lubricating oil pressure gauge, water temperature gauge, safety control for low lubricating oil pressure, safety control for high water temperature, safety control for over speed, hour meter and RPM meter indicator, battery. charging ammeter. The engine should be capable of providing 10% overload for one hour for every 11 hours continuous running at full load.

d]. ALTERNATOR: KIRLOSKAR GREEN make / Equivalent Alternator rated at 160 KVA, 415V, 0.8PF, 50Hz, 3phase , 4wire self regulated and self exited with voltage regulation of + or 1% class “H” insulation in SPDP enclosure and confirming to IS 4722/BS 2613, suitable for close coupling. trip proof with IP21 protection as per ISI.

1) Low lubrication oil pressure 2) Over speed 3)High water temperature The panel should be complete with bus bars internal connections and with necessary fuses, cables and other accessories and with tapping for the incoming supply from the alternator and for the outgoing supply to the load

f].FUEL TANK: Fuel tank of 400 liters capacity to generator with inlet and outlet connection filling cap drain plug level indicator etc., complete.

g].BASE FRAME: The base frame should be fabricated with MS channel of rigidly welded constructed for mounting the generator set. The engine and alternator should be coupled by suitably designed diaphragm type flexible coupling with guard and mounted on the base frame with proper alignment. The supply of generator set includes loading, unloading and transportation charges.

h]. Supply of maintenance and operating manual with list of engine parts and alternator parts. j]. Erection Testing and Commissioning The erection shall comprise of I].Providing suitable concrete foundation with plain cement concrete 1:2:4 with stand cushion all around the foundation -1Job II]. Providing ISI earthling with earth electrode of 2.1 meter length, 1 ½ ” diameter class ‘B’ GI pipe for the alternator and control panel including masonry work with cover slabs for earth pits -2 Nos III]Providing earth connection and interconnection of earth pit by 1”x1/8” copper conductor - 30 meters

BATTERY:1 No's 25 plate 100 AH 12V battery with one set of connecting leads of 75 Sq.mm copper cable with sockets etc.,

MANUALS & DOCUMENTATION : Operation and maintenance manual for engine, maintenance manual for alternator, engine test certificate, alternator test certificate, circuit diagram for control panel, DG set test certificate, CPCB compliance label fixed on canopy.

Supply of ACOUSTIC ENCLOSURE suitable for 160KVA Diesel Generator set. The acoustic enclosure should be free standing floor mounting type with modular construction with the provision to assemble and dismantle easily and designed to suit all weather conditions

The construction details / specification: Acoustic Modules: Outer body: 2mm thick CRCA sheet Door: 2mm thick CRCA sheet Inner surface:0.8mm thick GI perforated sheet / Perforation area should be > 2 / 3 of total area Insulation:100mm thickRockWool (Density: 65kg / cub.m or as approved by competent authority) to suit CPCB norms Skeleton structure Channels: should not be less than ISMC75 and ISMC 100.Cleats: should not be less angle 40x6mm and 50x 6mm.

The sheet metal competent shall be pre-treated by seven tank process. The joints should be designed in such a way the airborne noises are prevented. For larger panels, special care should be taken to prevent deformation. Adequate ventilators should be provided so that the generator performance is not affected and also the temperature inside is limited.

The maximum permissible sound pressure level should be as per the norms prescribed by the central Pollution Control Board/ State Pollution Control Board / Competent Authority concerned or should be 75db(A) at 1meter from the enclosure surface, whichever is advantageous to the department The emergency stop and suitable meter with digital display to indicate inside ambient temperature of the enclosure should be available on the enclosure panel. The enclosure should be only poly polished based coated inside and outside The enclosure provided shall be duly approved by the Engine Manufacture of the Engine provide for Diesel Generator sets mounted inside and should be to the satisfaction of Inspection / Testing Authority concerned.

Suplly and installation of exhaust piping of sufficient length with suitable MS pipes so asa to extenf\d outside the generator room with necessary thermal insulation (SR)

Providing fuel oil to run the set for 8 hours on load testing and commissioning using water rheostat or suitable loading elements.

Supply and demonstration of the following safety accessories: a) 1metre x 1metre x ½ inch 11KV rubber mat – 2 Nos. b) One set of 4 Nos. 9 litre fire buckets with metal stand frame – 1 set.c) First aid box with medicines – 1 No. d) 11 KV rubber hand gloves – 2 Nos. e) 2kg capacity dry powder type fire extinguishers – 2Nos. f) Hand operated pump to transfer fuel from standard barrel to fuel tank – 1No. g) First aid chart in Tamil and English – 1 No. h) Battery water acidity tester – 1 No. i) Earth Discharge Rod - 1No. j) Danger Board - 1 No. Set

Preparation of site plan, physical layout, electrical line schematic diagram in 10 sets, getting drawing approval from CEIG, preparation of completion report, rectification report and arranging CEIG Inspection and obtaining safety certificate from CEIG, preparation of 1set of approved drawing and a copy of safety certificate in a neat frame work to be fixed in Generator room and payment of CEIG inspection fees.

Supply and Laying of 3 1/2 x 150 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clarnping of 3-1/2 x 150 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps.

Supply and fixing of brass cable gland for 3-1/2 x 150 sq.mm. PVC LTUG aluminium armoured cable with earth connection.

Supply and providing cable end termination of 3-1/2 x 150 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

CCTV Arrangements

Supply and Installation of IP Bullet Camera 4MP (1280 x 960) high resolution IR Bullet• HD video output • Low illumination 3D DNR & DWDR & BLC • IP66 rating• IR range: up to 30m • True day / night 1/3" Progressive CMOS, ICR, 0.01lux/F1.2 | 1280x 960: 25fps(P)/30fps(N) 6mm/F2.0 lens (4mm) | H.264/MJPEG | dual-stream, DWDR | 3D DNR | BLC | IR range: up to 30m | DC12V & PoE | IP66 | (DS-2CD2020-I IR Bracket included Make :Hikvision-Eq

Supply and Installation of NVR 16 Channel Third-party network cameras supported Up to 5 Megapixels resolution recordingHDMI and VGA output at up to 1920×1080P resolution HDD quota and group management Connectable to the third-party network cameras like ACTI, Arecont, Make: Hikvision-Eq

Supply and Installation of POE Switch NETGEAR-SWITCH-FS116P WIRED/24PORT SW

Supply and Laying of Cat 6 Cabling 0.5mm . armoured cables Make : Dlink -Eq

Supply and laying of 1” 25mm PVC pipe With accessories

Supply of fixing of 8TB hard disk

Renewal by supply and fixing of Samsung 163 cm (65 inches) Vision AI 4K Ultra HD Smart QLED TV QA65QEF1AULXL

Supply and Laying of HDMI cable20Mtrs

Supply and installation of following 4U inch width rack for ethernet switches with A.C. distribution box, wire manager, fan tray, lockable front tinted glass door and two pair angle to support the switch

Video conferencing system Arrangements

Supply and installation of Interactive panel with following specificationssize: PANEL 218.44 cm (86) IPS 16:9 Native Resolution 3840 x 2160 (UHD) Refresh Rate 60 Hz Brightness 40 nits Dynamic CR 5,000:1 Color Gamut NTSC 68 % Viewing Angle (H x V)178 º x 178 º Color Depth (Number of Colors) 1.07 Billion colors Response Time 8 ms (G to G) Surface Treatment (Haze) Haze 28 % Operation Hours (Hours/Day) 16/7 Portait / Landscape NO / YES CONNECTIVITY HDMI In YES (3 ea) HDMI In (HDCP Ver.) 2.2 RGB In YES Audio In YES RS232C In YES RJ45(LAN) In YES (1 ea) USB In USB3.0 Type A (4 ea), USB2.0 Type A (1 ea), USB Type C (1ea) HDMI Out YES Audio Out YES Touch USB USB 2.0 Type B (2 ea) RJ45(LAN) Out YES MECHANICAL SPECIFICATION Bezel Color Black Bezel Width T/R/L/B : 15/15/15/44 mm Weight (Head) 58.6 Kg Packed Weight 75.9 Kg Monitor Dimension (W x H x D, mm) 1957 × 1160 × 100 mm Handle YES VESA™ Standard Mount Interface (mm)800 x 600 mm

Carton Dimensions (W x H x D, mm) 2110 × 1283 × 225 mmFEATURE - HARDWAREInternal Memory (eMMC)64 GBWi-Fi/BT (Built-in), Auto Brightness Sensor,Power IndicatorFEATURE - SOFTWAREBooting Logo Image,PIP,,PBP,Screen Share,Smart Energy Saving,Wake on LANENVIRONMENT CONDITIONS,Operation Temperature,0 °C to 40 °C,Operation Humidity,10 % to 90 %,Power SupplyAC 100-240 V~, 50/60 Hz,Power TypeBuilt-in Power,POWER CONSUMPTIONMax.580 W,Typ.385 W,Power off0.5 W,DPM0.5 W,Others-BTU (British Thermal Unit)1314 BTU/Hr(Typ.), 1979 BTU/Hr(Max.),SOUNDSpeaker (Built-in) (15 W x 2)CERTIFICATIONSafetyCB / NRTL,EMCFCC Class "A" / CE,ERP / Energy Star,OPS COMPATIBILITY (Slot)OPS Power Built-in,SOFTWARE COMPATIBILITYConnected CareLANGUAGEOSD,Power Cord 3 M*1, USB Cable (Type A-Type B) 5 M*1, HDMI Cable 3 M*1, Writing Pen*2 pcs, User Manual, QSG, Carton Box,

Remote Controller(include battery 2 ea), Wifi moduleOptionalWall Mount(WM-L000S), Floor Stand(ST-000F, ST-860F)SPECIAL FEATUREConformal Coating (Power Board)DEDICATED FEATURE - TOUCHAvailable Object Size for TouchØ2 mm ↑Response Time ('Paint' app on Windows 10 PC)5 ms ↓Accuracy (Typ.)±1 mmInterfaceUSB 2.0Protection Glass Thickness3 mm (Anti-Glare)Protection Glass Transmission88 %Operating System SupportWindows 7/8/10/Linux/Mac/Android (Linux/Mac Support one point touch)Multi Touch PointMax. 40 Points(Windows), Max. 32 Points(Android)DEDICATED FEATURE - CREATE BOARDCPUQuad core A55GPUMail G52 Multicore 2Memory(RAM)8 GBStorage64 GBWi-Fi802.11a/b/g/n/ac/ax (WiFi 6)LANGigabit LANBluetoothBluetooth 5.0OS ver. (Android)Android 13make::LG PANEL

Supply and installation of cpu Model KEi5012 Euro Intel Core i5 12th Generation 8GB DDR4 RAM 512GB SSD WIFI BT Windows 11 Pro License Pre-Loaded"

Supply and installation of mic with following specifications :Poly Trio C60 IP Conference Phone for Microsoft Teams and PoE-enabled No DECTPoly Trio C60 Power Supply with Power Cord and CAT-5Poly Trio C60 Expansion MicrophonesPoly Trio USB-A to Micro USB Cable (1.2M)1yr Partner Poly+ Trio C60Poly Studio E60 Smart Conf Camera Poly Studio E60 Power Adapter 1yr Partner Poly+ Poly Studio E60

PA system Arrangements

Supply and Installation of chairman unit Long flexible 18 inch gooseneck, Internal Loudspeaker automatically mutes LED Indicator, Headphones output.(Make: Bosch / Equivalent).

Supply and Installation of Delegate unit Long flexible 18 inch gooseneck, Internal Loudspeaker automatically mutes LED Indicator, Headphones output.(Make: Bosch / Equivalent).

Supply and Installation of Digital central control unit for conference system with monitor ,speaker and equalizer.

Supply and Installation of 20w RMS bidirectional speaker

Supply and Installation of 240.PA mixer amplifier

Supply and Installation of male female 13 M 8 pin digital extension cable

Renewal by Supply and Laying of HDMI 20mtrs cable with suitable PVC pipe.

Renewal by Supply & Installation of Multimedia Projector: 4300 ANSI Lumens , 1024 x 786 WXGA Resolutions with HDMI, USB, VGA, RCA input, (Make: BenQ/ Hitachi / Equivalent).

Renewal by Supply & Installation of 10’x 8’ feet Motorized Screen with Remote Control. (Make: Logic /Libert / Equivalent).

supply and Laying of 8 core 7/36 shielded conference cable with PVC pipe and accessories etc.

supply and Laying of 2 core 1.5 sq.mm shielded copper speaker wire

Super Conductor Lightning Diverter

Super Conductor Lightning Diverter Type: Single Stage /Serial No: JR-SC1/d2 Designation: Single Stage Silver Code Super Conductor Lightning diverter with Silver tipped Receiver, Diffuser, H.T Divider With discharging diverter.Certified by : CPRI [Positive & negative current inpulesshots of 8/20uS wave as per IEC 60099-4 with magnitude of 40kA+10%.

supplying and Fixing of 33 K.V – H.T Insulator including materials.(33KV SOLIDCORE POST INSULATOR / C6-170)Test Specification : IS: 2544-1973/ICE -60168-2001.Lightning impulse withstand voltage:(1.1/50u sec. wave)

Supplying and Laying the Copper Wire 6 SWG for open air network system.

Mini – Cylindrical Tower with Base platform.

Supplying and Fixing G.I centre sturdy pole.

Supplying and Fixing porcelain wall insulator with PVC pipe, clamps &screws etc.

Supplying and Fixing 11KV Porcelain Insulator with spike and holders, for Open air – net work system.

Supplying and Digging (Earth cell) and providing earth chemicals, earth discharging units with copper base plate.

Providing Scalp holding for the building bottom to top of the building rented and minor civil work.

RMG Unit Supply, Erection, testing and commissioning of 11KV 25 KA 630Amps 3 Panel HT OUTDOOR RING MAIN GEAR Switch board suitable comprising two incomer panels with Air Break/ load Breaks switches and one outgoing panel with Vacuum Circuit Breaker complete as per specification with Mechanical inter lock between incomers 1. Supply and Erection of draw out type 11KV 25 KA 630 Amps Horizontal draw out./Horizontal Isolation VACCUM CIRCUIT BREAKER fitted with motor ( 230 V AC) operated spring charged Mechanism, with ON and Off indicator Anti pumping Device, 110V DC shunt trip and closing coils ( DC source of supply to be derived from a power pack suitable for three Tripping and two closing operations incorporated on Incoming panel only) Mechanical Operation counter, 4 No + NC spare Aux contact with contact multiplication contractor for customer use. Automatic safety shitter, Mechanical close/Trip Knob, Mechanical ON/OFF Indication, operating Handle, 230V AC to 110V DC power pack operating handle

Indoor Three Panel Consumer VCB: Supply, erection, testing, commissioning and of 11KV 25KA HT Three panel Vacuum Circuit Breaker Switch, Indoor type for installation, board comprising one Incomer VCB and 2 Nos Outgoing 630A 500MVA VCB.1.Draw out type 11KV 500MVA 630A Horizontal Draw out/ Horizontal Isolation VCB operated with spring charged mechanism.Anti Pumping device ,110V DC Shunt Trip and closing Coils (DC source of supply to be derived from a Power pack suitable for 3 Tripping and Two closing operation counter, 4NO + 4NC spare Aux. Contact for customer use, Automatic safety shutter, Mechanical Close/ Trip knob, Mechanical ON/OFF indication,

Operating Handle, 110V AC-110V DC Power Pack etc. (Incom-1 & Outgoing-2Nos) Core(Core 1-15VA class 1 for metering and core 2-15VA 5P 10 for Protection) Incoming 1 No, Current Transformers of 30/5-5 Amps Dual Core (Core 1-15VA Class 1 for Metering and Core 2-15VA 5P 10 for Protection)(Outgoing-1) 4.Meters: 2. 11KV/Root 3/ 110V/ Root3- Three Phase, 3 Limb 200VA Class 1 Resin Cast Draw out type Potential transformers complete with HT and LT HRC fuses. (Incoming-1 No)

8. Phase Indication Lamps R,Y,B(Incomings 3Nos) 9. Control Wiring 10. 800Amps Copper Bus bar PVC Sleeved and required panel copper earthing. 11. Control switch TNC (Incoming-1 No, Outgoing -1No) 12.Trip Circuit healthy Push Button(Incoming-1 No, Outgoing -1No) 13. Common for Switch gear, MCB's for AC DC Control, Heater ON/OFF Switch with space Heater and thermostat Single phase switch socket, cubicle illumination lamp, Disconnecting type terminal Block.etc., 14. MS Sheet enclosure for Indoor Installations Powder.

TRANSFORMERS: Design, Supply, unloading, handling, safe keeping, Installation, testing and commissioning of 250kVA, 11KV/433V, DYN11 Outdoor, ONAN type transformer with OLTC & RTCC panel which consisting PT, AVR etc. The tapping on HV for HV variation shall be of (+5)% to (-15)% in step of 1.25% by OLTC. Necssary CTs including NCT, control switches and transformer Protection relays should be provided in transformer such as transformer Buchholz relay, OLTC surge relay, Oil temperature relay, winding temperature relay, magnetic oil level gauge and pressure relief valve with NO/NC, Auxiliary relays for alarm & tripping as per standards. The transformer should be complied Energy efficiency Level-2 as per IS-1180. The primary and secondary winding material shall be of copper.

All hardware shall be hot dipped galvanised. The copper flexible strip shall be provided at every gasketted joint for earthing continuity purpose. The Transformer shall be provided with cable termination box on primary side to terminate with all accessories as per the detailed specification and drawing enclosed.

Design, Supply, erection, testing and commissioning of 630A 4 pole MCCB of Microprocessor board EDO Type panel board suitable for operation on 415 V 3 phase, 50 Hz A.C supply, dust and vermin proof and accommodating the following ACB as Incomer unit with the following items of work complete to satisfy the CEA Rules and CEIG guidelines with Bus bar chambers, Main switches chambers and cable entry chambers. Bus bar chamber: Supply and fixing of suitable bus bar chamber made up of 16SWG MS sheet steel(1.8mm) with 2” X 1/2” tinned copper bus bar for 3 phases and neutral (50mm x 12mm) and 2 Nos. of earth bus of size 1” X 1/4 tinned copper bus(25mm x 6mm) on suitable bus bar insulator(Epoxy insulator) with maximum creepage distance and supported on MS Base channel frame work of size 10*3*2–1Set

Main Switches Chamber: Incoming 1)Supply and fixing of 2 No. 630A 4pole MCCB of Microprocessor board basic rating 4 pole 433V LT MCCB confirming to IS13947–2 IEC 60947–2 with suitable capacity and breaking capacity of drawout 65 KA breaking capacity with all accessories for standard horizontal manual draw out type ACB equipped with auxiliary contacts and all accessories for closing and opening operation with Microprocessor Based SR 18 G relay, over current trip device adjustable to LTD, STD and release for over current protection UV release with time delay, EF release short circuit protection, Mains CTs for 3 phases lockout, features, separate mold base for each pole for easy maintenance all relevant protection safety accessories as per CEIG, CEA ( MSES) 2023 Regulations in force with inter connection and terminations as required in specification

Providing ON/OFF switch, emergency lockable push button, Demand controller with RS485, Ammeter, Voltmeter, ,MD Controller, Earthfault relay , CTs, control MPCB/MCB/ ELCB/RCBOs, RYB Indication lamps and “ON/OFF/Trip" indicating lamp, Class "B" surge protection device with control fuses etc. and also refer the specification and SLD.

Buscoupler :800 Amps 4Pole 50kA electrical draw out type Air circuit breaker with shunt release shutter assembly, door interlock and other accessories - 1 No.

Outgoing 1) Supply and fixing of 250A TPN Double break switch with HRC Fuse- 8 Nos

Inter connecting the all LT MCCB and Switches to bus bar with suitable insulated tinned copper flats and painting/PVC sleeve color coding of phases and neutral indication. Double Earth connection of the switches and ACB’s to earth bus using suitable tinned copper flats by 2 runs of 1” X 1/4”. Supply and fixing of RYB LED lamp arrangements with toggle switches to control each phases and with rigid connection in suitable separate compartments within the cubicle as per CEIG rules with 1set, supply and fixing Electronic Trivector meter EC,300N class 0.5 flush mounting L&T or equivalent make–ModelER300N.

Supply and fixing of danger board with Siemens grey powder coating with super scribing the names of places to which supply is fed feeder sizes of cables direction of cables etc. Erection of panel board complete with suitable foundation bolts and nuts including suitable M.S Channel, concreting ,testing and commissioning (L&T,C&S,SIEMENS,ABB/Equivalent) ( Essential Panel )

Supply and erection of 100 KVAR 415/440Volts 50Hz 3 Ph automatic power factor correction panel, 8 stage, (at 0.95 lag), made up of powder coated, 14/16 SWG CRCA sheet steel enclosure with 1 1/2" x 1 1 1/2" x 1/2" AI Frame work with RCC concreting foundation and bolted to masonry pedestal with 250A triple pole MCCB as incoming (L&T/Siemens/C&S) with Delta Connected capacitors (BCH/EPCOS) MOO Type operating in multiple stage with 3 current and Voltage Transducers (CVT) at the phases simultaneously to activate the desired power factor switching time between steps 120 seconds, switching off time in case of fault 3 seconds with a LCD display to show the following Parameters.

A. Vr – R phase Line Voltage B. Vy – Y phase Line Voltage C Vb – B phase Line Voltage D. Ir – R phase Line current E. Iy – Y phase line current F. Ib – B phase Line Current G. KW – Present Kilo Watts H. RKVA – Present KVAR Demand I. KVA – Present KVA j. PF – Present Power Factor K. Number of Capacitor bank ON/OFF L. Provision to indicate the imbalanced load

Provision to indicate the change in phase Sequence The APFC Panel Should also with built in protection For high Voltage/Low Voltage cut off, single phase Preventer in current line surge line surges, Current Limiters, Current Sensor, etc., with connection complete and as per the relevant IE Rules. Eight Stages of Automatic Power Factor control panel is necessary connection.

Supply and Clamping of 3 C x 240 Sq.mm. 11 KV HT XLPE cable in a suitable 6" duro pipe to be excavated at a depth of 0.75 metre and covering the cable completely and refiling the earth to make good.(Make Gloster/Havells/ Polycab / Equivalent). (From VCB to Tr1 and Tr2)

Supply and Laying of 3 C x 240 Sq.mm. 11 KV HT XLPE PVC cable with aluminium conductors on wall with MS clamp with necessary supports or in a existing trench including removing and relaying the cement slab. (From RMG to VCB) (Make Gloster/Havells/ Polycab / Equivalent).

Supply and Providing cable end termination for 11KV 3 core 240 Sqmm XLPE HTUG cable with necessary Indoor type heat shrinkable joint kit and accessories (Make: Raychem or Equivalent).

Supply and Providing cable end termination for 11KV 3 core 240 Sqmm XLPE HTUG cable with necessary Outdoor type heat shrinkable joint kit and accessories (Make: Raychem or Equivalent).

Supply, fixing and demonstration of the following safety accessories and tools: Safety Accessories for 11 KV-substation AC chargeable emergency lamp 2x11w PL lamp lamp with all connected accessories.Rubber Mat 1m X 2m - 5 Nos.First Aid Box-3 Nos,shock treatment chart fixed in glass frame, 4 Fire Bucket 40x40x6mm ms angle with stand -3 Set. Hand Gloves in glass frame- 4 Nos. (2 pair) .Metallic danger board as required by the electrical authorities Fire Extinguisher-DCP- 5 Kg’s - 6 Nos. Earth Discharge Rod-1 No

Preparation of site plan, physical layout, electrical line schematic diagram 10 sets, getting drawing approval from CEIG, preparation of completion report, rectification report, etc., and arranging CEIG inspection and obtaining safety certificate from CEIG, payment of CEIG inspection fees and preparation of one set approved drawing and copy of safety certificate in a neat frame work and like fixed as HT substation.

Supply and Laying of 2 Run of 3 1/2 x 185 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good (From TF to MV Panel)

Supply and fixing of brass cable gland for 3-1/2 x 185 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 185 sq.mm.PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and fixing of aesthetically designed decorative IP 54, 18w Aluminium die cast, silver grey, garden light of dimenfon 600 mmx210 mm with terminal connections ( DUNE B5 LOBRD 60 LUKER MAKE/Equivalent)

Design, Engineering, supply, fabrication. Erection, Testing commissioning and handing over of 1 No. Goods (Dump) Lift (Gear with machine Room) as per the following Technical Specification. 1.Type of Lift : Dump waiter lift 2. Capacity of Lift : 500 Kg 3. Speed : 1.0 Meter/Sec 4. Type of Drive: specific Variable Voltage Variable Frequency V3F Drive with Enhanced ride comfort and levelling functions. 5. No. of Floors/Stops : Ground+1 Floors/ 2 Stop 6. Total Travel : 12 Metres 7. Levelling Accuracy: High Level Accuracy with Smooth and jerk free stopping. 8. Construction of Car: High quality and suitable thickness S.S.car and MS false ceiling 9. Position of Machine: Directly above the Lift shaft. 10. No. of Landing Entrance : 2 (Ground +First ) 11. No. of car Entrance: One in Front only. 12. Car Entrance Door: Power Operated V3F drive side Opening Sliding Precoated Decorative laminated Doors with VF operation.

13. Landing Entrance Door: Power Operated V3F driver Side Opening S.S Doors with provision emergency key opening at all Landings. 14. Lift Well Existing: 3.14 m (width) X 3.69 m (depth). 15. Lift Pit Depth required: 1250 mm 16. Car Size : 1000 mm (Width) X 1000 mm (Depth) X 1200mm (Height) 18. Power Supply: 400 / 440 V, 3 Phase, 50Cycles / Sec AC supply for power and 230V 50HZ single phase AC Supply for light at machine room with proper two distinct earth flat of adequate size from ISI earthing at ground floor. 19. Control: Microcomputer (Microprocessor) based Simplex, Collective control with or without attendant. 20. Car Fittings: Compact Fluorescent Lighting with 2 Nos.300 mm Sweep Cabin Fan. 21. Lift Well: R.C.C Construction with Brick Masonry. 22. Indication: UP/DOWN Digital Direction and position indicator for all landing and inside the car. 23. Emergency Alarm Bell: Battery Operated alarm bell with Automatic Charging Device.

24. Emergency Light: Battery operated Light with Automatic Charging Device. 25. Fire Man’s Switch: Include at Ground Floor.26. Scaffolding: Included. 27. M.S. Sill angels and facis Plates: Included 28. Steel for Lift Machinery: Included 29.Servicing and maintenance: Free comprehensive servicing and maintenance during the guarantee period of one year.30. Automatic Rescue Device: To facilitate the landing of the lift to the nearest floor at the time of Power Failure. This shall consists of suitable type of Battery system with charger, invertor, under Voltage Protection system etc., Complete with all Accessories.31. Provision of Intercom with phone: Included 32. Lift Licence: Preparation of Drawing, payment of Charges to CEIG / Lift inspectorate and insurance policies if any and obtaining CEIG safety certificate as per Lift Act. 33. Floor Annunciator with music: Included

. 34. SPECIAL FEATURE: A.) Infra-Red colour Sensor with Height Screen. B.) Stainless steel signal fixtures. C.) Vandal Proof Button with S.S Cover. D.) S.S door frames for landing doors. E.) VF Door operator. F.) Calls register Signal. G.) Precoated decorative laminated sheet for car operating Panel and landing fixtures. H.) ON-OFF Switch for Light. 35. Lift Duty motor of adequate capacity reduction worm gear, electromagnetic brake with compression springs, over speed Governor, Phase failure and phase reversal relay, alarm Bell, T Guide Brackets for car and Counter weight, Rubber padding under winding unit, car safety Gears, Buffer, Electro Mechanical Door Locks, Emergency Key, Side supporting angles motor Over Load Protection Devices. Final limit Switch, main suspension ropes, Counter weights, Lifting Joist for Mounting the Machineries. 36. Site testing in accordance with IS 14556 should be carried out at the time of handing over. (JOHNSON/OTIS/Kone)

Please Enable Macros to View BoQ information