Renovation of Saryu Drainage Khand-2, Balrampur Division Office

Amount

RENOVATION OF SARYU DRAINAGE KHAND-2, BALRAMPUR, DIVISION OFFICE (CIVIL WORK, PHE WORK, ELECTRICAL WORK)

Earth work in digging foundation of masonry work in all type of soil; including all lead and lift with disposal of earth as per direction of Engineer in charge

Laying C.C. M-10 (1:3:6) mix in floor with Dala shingle 4.75 to 40 mm size coarse sand of F.M. not less than 2.0, including all cost of material, labour, T & P etc. required

First class brick work in 1:4 C:M with coarse sand of F.M. not less then 2.0, including all cost of material, labour, T & P etc. required for proper completion of work.

Dismentling existing plaster including distposal of refuse as directed by the engineer-in -charge with in a distance of 60 mtr. (200 feet).

12 mm. thick plaster with cement mortar in proportion of 1:4 cement &fine sand of 1.25 F.M.

P/L vitrified floor Tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make in all colours and shade, laid on 20 mm thick cement mortar 1:4(1cement 3 course sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc. complete.(over all rate) Size of Tile 600 x 600 mm

P/L vitrified Tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make in all colours and shade, in skirting, riser of steps over 12mm thick bed of cement mortar 1:3(1cement 3 course sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc. complete.(over all rate) size of Tile 600 x 600 mm

Scraping old white or color wash including disposal of refuse as directed by the engineer-in -charge with in a distance of 60 mtr. (200 feet)

Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete.

Painting two coat of superior quality of synthetic enamel paint approved make as per item No.12 on new wooden surface (excluding cost of primary) including cost of all material, labour T&P etc. required for proper completion of work

Writing letter on sign board above 50 mm size but below 80 mm size

Finishing wall with water proofing cement paint of approved make such as super snowcem, Durocem, robiecem, Guttu cem, Super cem quality and of required shade on new wall surface (two coats) over one coat of white cement primer to give an even shade after thoroughly brushing the surface to remove powdered materials including curing and cost of all materials.

Fabrication of Angle Iron truss including cutting, drilling holes, riveting/welding as necessary with one coat of red oxide primer and its carriage upto site including cost of all material, labour, T&P etc. required for proper completion of work.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GISUB HEAD : 12- ROOFING 878 adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T?sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge (a )GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.

Providing & fixing 12mm. (1/2") thick and 100mm. (4") wide blackboard pelmets with 19 mm.dia. Aluminum curtain rod and brackets, including fixing with 25x3mm. (1"xl/8") M.S. flat 10cm. (4") long and plug etc. complete with painting, polishing or oiling as required including cost of materials.

Dismantling door or window including chaukhat with holdfast and including stacking of materials as directed by Engineer-in- charge within a distance of 60M

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) Second class teak wood(35 mm thick shutters )

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing ISI marked Stainless Steel butt hinges instead of M.S. pressed butt hinges bright finished of required size with necessary screws. (Shutter area to be measured).

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : (Size 250x16 mm)

Providing and fixing chromium plated brass handles with necessary screws etc. (a) 125mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : (a )200x10mm

(b) 100x1ommm

Dismantling of G.I. sheet roofing/ Wall partition including stacking within 100 M.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12873 SUB HEAD : 12- ROOFING metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : (Ridges plain (500 - 600mm)

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm)

Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x1.6 mm hollow MS tube, placed along the walls, ceiling and floor in a grid pattern with spacing @ 60 cm centre to centre both ways (vertically & horizontally) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge.

Providing and fixing Pre -laminated medium density fibre board exterior grade (Grade-I) IS:14587:1998 marked, to frame, backing or studding with screws etc. complete ( Frames, backing or studding to be paid separately). Pre-laminated with decorative lamination on both side exterior Grade - I MDF Board 12 mm thick confirming to IS:14587

Removing old paint from steel/wooden surface with paint remover of approved brand or with caustic soda and making the surface even including cost of all material.

Painting one coat of synthetic enamel paint on old surface with superior quality approved make as mentioned in item No.12 including cost of all material labour T&P etc. required for proper completion of work.

Painting one coat of red oxide primer on steel surface after sand papering and cleaning of surface including cost of all material, labour T&P required for proper completion of work

Painting two coat of superior quality of synthetic enamel paint approved make as peitem No.12 on new wooden surface (excluding cost of primary) including cost of all material, labour T&P etc. required for proper completion of work.

Providing and injecting chemical emulsion for pre-constructional antitermite treatment and creating a chemical barrier under and allround the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the external perimeter of binding expansion joints, surrounding of pipes and conduit etc. complete (Plinth area of the building at ground floor only shall be measured as per I.S.:6313 (Part II 1981) Aldrine emulsifiable concentrate or any other approved material such as Heptachlor or chlordane will be used. The rate of application of chemical emulsion shall be as follows: Treatment of top surface of plinth filling (5 Liters per Sqm.)

Providing and fixing brass bib cock of approved quality :

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Wiring point for light with 1.5 Sq. mm. PVC insulated single core cable in heavy gauge PVC conduit pipe concealed in the wall complete with 8 SWG G.I. earth continuity wire and piano type switch etc. complete in all-respect.

Wiring point for fan/fresh air fan (light duty exhaust fan) with 1.5 sq.mm. PVC insulated single core cable in heavy gauge PVC conduit Pipe concealed in the wall complete with 8 SWG Gl earth continuity wire and piano type switch etc. complete in all respects.

Wiring point for plug with 1.5 sq.mm. PVC insulated single core cable in heavy gauge PVC conduit concealed in the wall complete with 8 SWG Gl wire earth continuity wire and piano type switch and socket etc. complete in all respects.

Wiring point for call bell with 1.5 sq.mm. PVC insulated single

Wiring point for light and fan with 1.5 sq. mm. PVC insulated single core cable in heavy gauge PVC conduit pipe partly concealed in wall and partly laid in slab along with the reinforcement before concreting, complete with 8 SWG Gl earth continuity wire and piano type switch etc. complete in all respects.

Erection & testing of ceiling fan and regulator etc. excluding supply of down rod, complete in all respects.

Erection & testing of exhaust fan on the exiting hole with suitable size or rag bolts, nut & washer etc. complete in all respects.

S/F of power plug with 15A/250V flush type switch and 3 pin 15A/250V flush type socket in suitable M.S. box of 175x100x50 mm. size with Bakelite sheet cover 3mm thick fixed with brass machine screws and cum washer.

S/F of fire bucket, round bottom made of G.I. sheet 9-11 liters capacity duly painted as per fire brigade design, supported on hanging bracket, chained and locked, initially filled with fine river sand, water as per directions of Engineer?in-charge.

S/F fire extinguisher, dry chemical types 5.00Kg. capacity (ISI Mark) complete with initial charge & wall bracket along with supply of all materials & labour for proper completion of work.

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required Size 300 mm width X 50 mm depth X 1.6 mm thickness

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. (a )2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

(b )2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

(c )2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required (a) 1 x 1.5 sq. mm

(b )2 x 2.5 sq. mm

(c) 2 x 4 sq. mm

S/F of factory wire H.P.F. box type fluorescent tube light fitting suitable for 1x40 watt fluorescent tube complete including tube etc. on surface, complete in all respect of Philips/Bajaj/G.E.C. or Crompton make.

Same as above for 2 x 40 watt fluorescent tube.

S/F of 16A. 415V metal clad T.P.N. rewirable type switch fuse unit on teak wood board, complete in all respect

Supplying and fixing of 33A. 415V metal clad T.P.N. rewirable type switch fuse unit on teak wood board complete in all respect.

M/S RAJESH KUMAR MISHRA CONTRACTOR

M/S DHARMENDRA KUMAR THEKEDAR

VINAY PRAKASH SHUKLA

m/s kanihya lal yadav

M/S RAM PAYRE MISHRA CONTRECTOR

AMRENDRA KUMAR TRIPATHI

M/S RAM KRISHAN MISHRA CONTRECTOR

RAMRAJ MISHRA CONTRACTOR