Modernization and Upgradation of Govt. High Secondary School Nagrota Gujroo.

Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge All kinds of soil :

Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil :

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres in All kinds of soil

Extra for every additional lift of 1.5 m or part thereof in excavation/banking excavated or stacked material : All kinds of soil :

Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts,struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etcupto floor V level, including curing but excluding the cost of centring, shuttering and finishing with. 1:5:10 (1 cement : 5 coarse sand : 10 graded brick aggregate 40 mm nominal size

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete inclu. curing but excluding the cost of centering, shuttering, finishing & reinforcement. All works upto plinth level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone agg. 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centring and shuttering including strutting propping etc and removal of form work

Foundations, footings, bases of columns etc. for mass concrete

columns, Pillars,Piers, Abutments, Posts and Struts.

Suspended floors, roofs, landing, balconies and access platforms.

Lintel, beams, plinth beams, girders, bressumers and cantilevers.

Stairs (excluding landings) except spiral staircases.

Edge of slabs and break in floors and walls Under 20 cms wide.

Weather shade, chajjas, corbels etc., including edges.

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Clearing jungle including uprooting of rank vegetation grass, bushwood, trees and saplings of girth upto 30 cm measured at height of 1m above the ground level and removal of rubbish outside the periphery of the area cleared including all leads & lifts and average upto 1.5 mtr width should be cleared on both side of the B.T. surface (for complete job).

Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunk and branches, removing the roots and stacking of serviceable material and disposal of unserviceable materials:-

Beyond 30 cm girth upto and including 60 cm girth

Beyond 60 cm girth upto and including 120 cm girth.

Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and curing complete.

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth including all shapes, leads, lifts and carriage of material by MT / H.L. in cement mortar 1:6 ( 1 cement : 6 coarse sand)

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Sal wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately) Second class teak wood 35 mm thick.

Providing and fixing 35mm glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. Second class Kail wood

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : Second class Kail wood

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick Decorative ply wood both side decorative veneer (type 1) conforming to IS 1328 BWR type

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete. Fixed to openings / wooden frames with rawl plugs screws etc.

Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers’ specifications: Painting steel work with deluxe multi surface paint of required shade to give an even shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.80litre/10sqm of approved brand and manufacture

Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers’ specifications: Painting wood work with deluxe multi surface paint of required shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.75litre/10sqm of approved brand and manufacture

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand and manufacturer, in all colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of tile 600x600 mm

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. In colour such as White, Ivory, Grey, Fume Red Brown

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Kota stone slab flooring 25 mm thick over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing, polishing, making of edge moulding & nosing and curing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) :

Kota stone slab 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm ( average) thick cement mortar 1:3 (1 cement:3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing, polishing, making of edge moulding & nosing and curing complete.

Extra for kota stone/sand stone flooring in treads of steps and risers using single length up to 1.05 meter

Extra for pre finished nosing in treads of steps of kota stone/ sand stone slab.

Chequerred precast cement concrete tiles 22mm thick in footpath and courtyard, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing, cleaning and curing complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) Light shade using white cement

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggreagate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement: 3 fine sand) as per standard design. In 75x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement: 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm . This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and laying integral cement based water proofing treatment including preparation of surfaces as required for treatment of roofs, balconies, terraces etc consisting of following operations. a) Applying a slurry coat of neat cement using 2.75kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over the RCC Slab including adjoining walls upto 300mm height including cleaning the surface before treatment.b) Laying brick bats with mortar using broken bricks/ Brick Bats 25mm to 115mm size with 50% of Cement mortar 1:5 (1 Cement : 5 coarsesand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 (1 Cement : 5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer in-charge to required slope and treating similarly the adjoining walls upto 300mm height including rounding of Junctions of walls and slabs)c) After two days of proper curing applying a second coat of cement slurry using 2.75kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge.d) finishing the surface with 20mm thick joint less cement mortar of mix 1:4(1 cement: 4 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300mm/sq 3mm deep.e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by Engineer in-charge. With average thickness of 120mm and minimum thickness at khurra as 65 mm

6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm . This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

15mm Cement plaster on the rough side of single or half brick wall of mix: 1 : 6 ( 1 cement : 6 fine sand)

20mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand)

Add for plaster drip course/groover in plastered surface or moulding to R.C.C Projections

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacture, over the plastered wall surface to prepare the surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface.

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour two course.

Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 liter/10sqm) over and including base coat of exterior primer applied @ 2.20kg/10sqm

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 100x10 mm

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Providing and fixing aluminum tubular handle bar 32mm outer dia, 3.0mm thick & 2100mm long with SS screw etc. complete as per direction of Engineer-in-charge. Powder coated minimum thickness 50 micron aluminum tabular handle bar

Providing and fixing aluminum hanging floor door stopper, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparentor dyed to required colour or shade with necessary screws etc. complete : Twin rubber stopper

Providing and fixing bright finished brass hard drawn hooks and eyes

Providing and fixing door back rubber stopper 75 mm long with necessary nut and bolt.

Providing and fixing aluminum extruded section body tubular type universal hydraulic door closer,(having brand logo with IS: 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete :

Supplying chemical emulsion in sealed containers including delivery as specified. Chlorophriphos/Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL antitermite treatment. (excluding the cost of chemical emulsion): Treatment of soil under existing floors using chemical emulsion (Chlorophriphos/Lindane E.C. 20% with 1% concentration) @ one litre per hole, 300mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floor:

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) For fixed portion Powder coated aluminum (minimum thickness of powder coated 50 microns)

For fixed portion Powder coated aluminum (minimum thickness of powder coated 50 microns)

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately.) Powder coated aluminum (minimum thickness of powder coated 50 microns)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-I type-II) in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in charge Prelaminated particle borad with decorative lamination on both sides.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete

Supplying and fixing C.I. cover without frame for manholes: 455x610mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound@ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670kg./sqm. and coarse sand @1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately) For the purpose of measurement the entire treated surface will be measured.

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with coarse sand etc. all complete as per direction of Engineer-in-charge.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm)

Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm)

Providing and fixing white vitreous china pedestal type water closet (European type W.C . .pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern including flush pipe with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures, complete including cutting and making good the walls and floors wherever requied W.C. pan with lSI marked white solid plastic seat and lid of make Hindware/Cera/Jaquar only:- (incl. All Carriages)

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I. clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required:One urinal basin with 5 liter white P.V.C automatic flushing cistern.

Providing and fixing Rectangular shaped urinal partition with frosted glass of 8 mm thickness having size 900x450 mm fitted with a pair of chrome plated hinges with all necessary screws and nuts all complete of approved brand and make Hindware/Cera/Jaquar or equivalent as approved by engineer in-charge at site

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer with 32 mm C.P. brass waste coupling of standard pattern, of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings of make Hindware/Cera/Jaquar only:- (incl. With Carriages)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink without drain board 470x420mm bowl depth 178mm

Providing and fixing C.P. Brass 3-way Tap/cock/faucet 15 mm nominal bore with necessary screws, brackets, nuts or bolts etc; all complete of make hindware/Cera/Jaguar only:- (With all Carriages)

Providing and fixing P.V.C waste pipe for sink or wash basin including P.V.C waste fitting complete. Flexible pipe 40 mm dia (With Carriages)

Providing and fixing PTMT grating of approved quality and colour circlular type 100 mm noinal dia

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete ISI marked of make Saint Gobin or Modi float or equivalnet brand as approved by Engineer incharge at site:- (With all Carriages)

Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C. P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc. complete of make hindware/Cera/Jaquar only:-

Providing and fixing unplasticised - Rigid PVC PIPES conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap of thermal expansion;with necessary stays / clamps with fasteners having working pressure of 4kg/cm2 of make Supreme or finolex only :- all complete including testing of joints and pipes for leakage etc.:- (Including cost / Carriage of material by Mechanical transport)

50 mm dia

75 mm dia

110 mm dia

160 mm dia

200 mm dia

250 mm dia

Providing and fixing unplasticised - PVC moulded fittings / accessories for unplasticised - Rigid PVC pipes conforming to IS : 13592 Type A including jointing with seal ring & insertion rubber washer 3 mm thick conforming to IS : 5382 leaving 10mm gap for thermal expansion; with necessary stays / clamps with fasteners bolts and nuts complete; having working pressure of 4kg/cm2 of make Supreme or finolex only :- all complete including testing of joints and pipes for leakage etc.:- (Including cost / Carriage of material by Mechanical transport) PVC PLAIN BEND (of required degree):-

50 mm dia.

75 mm dia.

110 mm dia

160 mm dia.

200 mm dia.

Providing and fixing unplasticised - PVC moulded fittings / accessories for unplasticised - Rigid PVC pipes conforming to IS : 13592 Type A including jointing with seal ring & insertion rubber washer 3 mm thick conforming to IS : 5382 leaving 10mm gap for thermal expansion; with necessary stays / clamps with fasteners bolts and nuts complete; having working pressure of 4kg/cm2 of make Supreme or finolex only :- all complete including testing of joints and pipes for leakage etc.:- (Including cost / Carriage of material by Mechanical transport) PVC DOOR BEND( of required degree):-

50 mm dia.

75 mm dia.

110 mm dia

160 mm dia.

200 mm dia.

Providing and fixing unplasticised - PVC moulded fittings / accessories for unplasticised - Rigid PVC pipes conforming to IS : 13592 Type A including jointing with seal ring & insertion rubber washer 3 mm thick conforming to IS : 5382 leaving 10mm gap for thermal expansion; with necessary stays / clamps with fasteners bolts and nuts complete; having working pressure of 4kg/cm2 of make Supreme or finolex only :- all complete including testing of joints and pipes for leakage etc.:- (Including cost / Carriage of material by Mechanical transport) PVC PLAIN TEE:-

50 mm dia.

75 mm dia.

110 mm dia

160 mm dia.

200 mm dia.

Providing and fixing unplasticised - PVC moulded fittings / accessories for unplasticised - Rigid PVC pipes conforming to IS : 13592 Type A including jointing with seal ring & insertion rubber washer 3 mm thick conforming to IS : 5382 leaving 10mm gap for thermal expansion; with necessary stays / clamps with fasteners bolts and nuts complete; having working pressure of 4kg/cm2 of make Supreme or finolex only :- all complete including testing of joints and pipes for leakage etc.:- (Including cost / Carriage of material by Mechanical transport) PVC DOOR TEE:-

50 mm dia.

75 mm dia.

110 mm dia

160 mm dia.

200 mm dia.

Providing and fixing unplasticised - PVC moulded fittings / accessories for unplasticised - Rigid PVC pipes conforming to IS : 13592 Type A including jointing with seal ring & insertion rubber washer 3 mm thick conforming to IS : 5382 leaving 10mm gap for thermal expansion; with necessary stays / clamps with fasteners bolts and nuts complete; having working pressure of 4kg/cm2 of make Supreme or finolex only :- all complete including testing of joints and pipes for leakage etc.:- (Including cost / Carriage of material by Mechanical transport) PVC REDUCER PLAIN TEE:-

110 mm x 75 mm

160 mm x 110 mm

200 mm x 160 mm

Providing and fixing unplasticised - PVC moulded fittings / accessories for unplasticised - Rigid PVC pipes conforming to IS : 13592 Type A including jointing with seal ring & insertion rubber washer 3 mm thick conforming to IS : 5382 leaving 10mm gap for thermal expansion; with necessary stays / clamps with fasteners bolts and nuts complete; having working pressure of 4kg/cm2 of make Supreme or finolex only :- all complete including testing of joints and pipes for leakage etc.:- (Including cost / Carriage of material by Mechanical transport) PVC REDUCER DOOR TEE:-

110 mm x 75 mm

160 mm x 110 mm

200 mm x 160 mm

Providing and fixing unplasticised - PVC moulded fittings / accessories for unplasticised - Rigid PVC pipes conforming to IS : 13592 Type A including jointing with seal ring & insertion rubber washer 3 mm thick conforming to IS : 5382 leaving 10mm gap for thermal expansion; with necessary stays / clamps with fasteners bolts and nuts complete; having working pressure of 4kg/cm2 of make Supreme or finolex only :- all complete including testing of joints and pipes for leakage etc.:- (Including cost / Carriage of material by Mechanical transport) PVC OFFSETS:-

50 mm PVC off sets

75 mm PVC off sets

110 mm PVC off sets

160 mm PVC off sets

200 mm PVC off sets

Providing and fixing unplasticised - PVC moulded fittings / accessories for unplasticised - Rigid PVC pipes conforming to IS : 13592 Type A including jointing with seal ring & insertion rubber washer 3 mm thick conforming to IS : 5382 leaving 10mm gap for thermal expansion; with necessary stays / clamps with fasteners bolts and nuts complete; having working pressure of 4kg/cm2 of make Supreme or finolex only :- all complete including testing of joints and pipes for leakage etc.:- (Including cost / Carriage of material by Mechanical transport) PVC COUPLER/COLLAR:-

50 mm dia

75mm dia

110mm dia

160 mm dia

200 mm dia

Providing and fixing unplasticised - PVC moulded fittings / accessories for unplasticised - Rigid PVC pipes conforming to IS : 13592 Type A including jointing with seal ring & insertion rubber washer 3 mm thick conforming to IS : 5382 leaving 10mm gap for thermal expansion; with necessary stays / clamps with fasteners bolts and nuts complete; having working pressure of 4kg/cm2 of make Supreme or finolex only :- all complete including testing of joints and pipes for leakage etc.:- (Including cost / Carriage of material by Mechanical transport) PVC VENT COWL:-

75mm dia

110mm dia

160 mm dia

Providing and fixing unplasticised - PVC moulded fittings / accessories for unplasticised - Rigid PVC pipes conforming to IS : 13592 Type A including jointing with seal ring & insertion rubber washer 3 mm thick conforming to IS : 5382 leaving 10mm gap for thermal expansion; with necessary stays / clamps with fasteners bolts and nuts complete; having working pressure of 4kg/cm2 of make Supreme or finolex only :- all complete including testing of joints and pipes for leakage etc.:- (Including cost / Carriage of material by Mechanical transport) PVC FLOOR/NAHANI TRAP:-

110 mm x 75 mm

110 mm x 100 mm

Providing and fixing unplasticised - PVC moulded fittings / accessories for unplasticised - Rigid PVC pipes conforming to IS : 13592 Type A including jointing with seal ring & insertion rubber washer 3 mm thick conforming to IS : 5382 leaving 10mm gap for thermal expansion; with necessary stays / clamps with fasteners bolts and nuts complete; having working pressure of 4kg/cm2 of make Supreme or finolex only :- all complete including testing of joints and pipes for leakage etc.:- (Including cost / Carriage of material by Mechanical transport) PVC P/Q/S TRAP:- 100 mm dia.

Providing and fixing Soap dish (C.P. brass) with brackets ,nuts & screws complete etc. of make hindware/Cera/Jaquar only:- (With all Carriages)

Providing and fixing (C.P. Brass ) towel ring trapezoidal shape 215 mm long, 200 mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangements of approved quality and colour, weighing not less than 88 gms.

Providing and fixing towel rail 600mm long (C.P. brass) with total length of 645 mm, 78 mm wide and effective height of 88 mm, weighing not less than 190 gms.with brackets ,nuts & screws complete etc. of make hindware/Cera/Jaquar only:- (With all Carriages)

Providing and fixing C.P. brass bib cock of approved quality conforming to IS : 8931 of make hindware/Cera/Jaquar only:- 15 mm nominal bore (With all Carriages)

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms of make hindware/Cera/Jaquar only:- 15 mm nominal bore (With all Carriages)

Providing and fixing C.P. brass angle valve for basin/wall mixer and geysers points of approved make conforming to IS : 8931 15 mm nominal bore of make hindware/cera/jaquar or as approved by site incharge (With all Carriages)

Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm length 15 mm nominal bore (With all Carriages)

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge all complete of make hindware/Cera/Jaquar only:-. (With all Carriages)

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-in- charge.(Incl. all carriages) Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc.

PN-16 pipe, 16mm OD(SDR-7.4)

PN-16 pipe , 20mm OD(SDR-7.4)

PN-16 pipe , 25mm OD(SDR-7.4)

PN-16 pipe , 32mm OD(SDR-7.4)

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-in- charge External work including trenching, refilling etc.

PN-16 pipe , 32mm OD (SDR-7.4

Providing and fixing PPR Union 20mm

Providing and fixing PPR Union 25mm

Providing and fixing PPR Union 32 mm

Providing and fixing PPR Union 50 mm

Providing and placing on terrace (at all floor levels) polyethylene water storage tank lSI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid lSI license] (incl. cost / carriage of material upto roof top).

Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour:- 25 mm nominal bore, weighing not less than 62gms

Providing & fixing BRASS BALL VALVE of approved quality conforming to IS : 8931 of make UNIK or DRP or as approved by site incharge (incl. all carriages)

25 mm nominal bore

32 mm nominal bore

Providing and fixing BRASS FLOAT BALL VALVE; High or low pressure with plastic floats:- of approved quality conforming to IS : 8931 of make UNIK or DRP or approved by engineer incharge at site:- 32 mm nominal bore (incl. all carriages)

Providing and fixing Gun metal gate valve with C.l. wheel of approved quality (screwed end) conforming to IS : 8931 of make UNIK or DRP or as approved by site incharge:- 25 mm nominal bore (incl. all carriages)

Providing and fixing Brass Foot valve with strainer/filter of approved quality (screwed end) conforming to IS : 8931 of make UNIK or DRP or as approved by site incharge:- 25 mm nominal bore (incl. all carriages)

Providing and fixing of stainless steel Rainwater Khurra JALI to be placed at roof and mumty levels of make CHILLY or CAMRY or equivalent all complete:- square or circular in shape of dia/size:- 150 mm (incl. all carriages)

Providing & Installation of 2.0 H.P. three phase water pump of make Crompton with all fittings, connecting inlet & outlet, fixtures, electrical connection and starter all complete:- (incl. all carriages)

Cutting holes up to 30x30 cm in walls including making good the same: With common burnt clay F.P.S. (non modular) bricks (Including cost / Carriage of material by Mechanical transport)

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 gradedstone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. (Including cost / Carriage of material by Mechanical transport)

Providing and fixing square- mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design. 100 x 100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) R.C.C. top slab with 1 :2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement: 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finsihed with a floating coat of neat cement complete as per standard design (Including cost / Carriage of material by Mechanical transport)

Inside size 90x80 cm and 45 cm deep including C.l. cover with frame (light duty) 455x610 mm. internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg):- With F.P.S. bricks with class designation 75 & with Crushed stone aggregate

Inside size 90x80 cm and 60 cm deep including C.l. cover with frame (light duty) 455x61 0 mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :- With F.P.S. bricks with class designation 75 & with (a) Crushed stone aggregate

Extra for depth for brick masonry manholes:- Size 90x80cm:- With F.P.S. bricks with class designation 75 (Including cost / Carriage of material by Mechanical transport)

Supplying & fixing C.I cover with frame for manhole in sump / septic tank 455x610mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg.

Making soak pit 2.5 m diameter 3.0 metre deep with 45x45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design by way of earth excavation by mechanical means; laying of 100 mm thick P.C.C. bed in 1:4:8 mix ratio & R.C.C. Slab on top in 1:1.5:3 mix ratio; providing and fixing of Manhole with MS frame and cover having passing of 50 mm dia. Vent air pipe through it for foul gases; brick masonry in 1:6 cement mortar mix with providing of pores; and filling of brick bat aggregates around the dry brick honey comb shaft; P/F of pvc bend/tee at the S.W. Drain pipe; all complete etc:- With F.P.S. bricks and Crushed (Including cost / Carriage of material by Mechanical transport)

Providing structural design/drawing duly vetted DIQC/IIT/NIT/GEET Jammu after due Geotechical investigations for Architectural,Structural, Plumbing, electrucal, Fire Fighting , Supervision, placement of building at site. condition Structural design as per safe bearing capacity of soil, wind pressure etc

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Extra for providing opening of required size and shape for wash basin/ kitchen sink in kitchen platform, vanity counters and similar location in marble/granite / stone work including necessary holes for pillar taps etc. including moulding, rubbing and polishing ofcut edges etc. complete.

Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite Work

carriages of materials by mechinical trancsport incl. loading, unloading and stacking complete

Earth for an lead of 3 kms (disposal of surplus earth)

Bricks for an lead of 35 kms

Sand for a lead of 25 kms.

stone agg above 40 mm size av. lead of 35 kms

stone agg below 40 mm size av. lead of 35 kms

Please Enable Macros to View BoQ information