Spl repair to carryout roof treatment in certain bldg. of Pawan Vihar and provn of toilet with wash basin at MT area incinerator for main Office complex at Old Cantt under GE (East) Prayagraj.

Amount

Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc., but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed.

M&L for brick work with fly ash (old size) bricks straight or curved on plan to any radius half brick thick wall built in CM (1:4) complete all as specified and directed.

M&L for brick work with fly ash (old size) bricks straight or curved on plan exceeding 6 m mean radius built in CM 1:6 complete all as specified and directed.

Dismantling brick tiles any size laid bedded and pointed in any mortor complete all as specified and directed.

Demolition of mud in roofs any thickness and in any position and leaping over roof terrace, removing the demolished material to a distance exceeding 500mtr & not exceeding 1.5 km and depositing where directed at a level not exceeding 1.5mtr above starting point, complete all as specified and as directed.

M&L for 25 mm average thick PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) in floors/padding mixed with WPC complete all as specified and directed. Note :- water proofing compund measured and paid seprately

M&L for providing cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) in roof kerb or mud stop, gola, rounded or chamfered on edge complete all as specified and directed.

Demolition of roof treatment (all layer i.e. bearing course (mortar) leveling course (PCC) waterproofing membrane etc.) complete including removal of debris outside the MoD land as specified and directed by Engineer-in-charge.

M&L for water proofing treatment over cleaned roof surface with bitumenous membrane comprising of the following and testing complete all as specified and directed.: (a) Preparation of roof surface by wire brush/coir brush and remove all dirt, grit, stone fungus and finely washing with water so as to ready for receiving WPC complete with entire satisfaction of Engineer-in-Charge. (b)Applying One coat of Bitumen primer confirming to IS-3384-1965 @ 0.5 kg per sqm. (c) Applying a tack coat of hot blown bitumen 85/25 @ 1.2 kg/sq.m confirming to IS-702-1998 for water proofing membrane. (d) Providing polymeric waterproofing membrane asphaltic polythene film having weight not less than 3 kg per sq.m with 100 mm wide side or end lap and 75mm along the length from down lamps to upward completely sealed with hot blown lamps. (e) Again applying a tack coat of hot blown bitumen 85/25 @ 1.2 kg/sq.m confirming to IS-702-1998 for water proofing membrane. (f) Spraying binding materials such in dry condition @ 0.5 to 1.0 kg/sqm shall be dusted over bitumen complete with leaking teasing, complete all as specified and directed.

Cement concrete tiles 25cm x 25cm x 22 mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished built with grey cement and no pigment over and including 15 mm thick screed bed in cement mortar 1:4 with water proofing compound complete all as specified. Note :- water proofing compund measured and paid seprately

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) area opening not exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) area of opening exceeding 1.5 Sqm but not exceeding 4.00 Sqm each complete all as specified and directed.

Providing and fixing factory made uPVC white colour sliding window three track made of extruded profiles with wall thickness of 2.3mm(+ - 0.2 mm). Window profile with hollow section with multi chamber.Frame (88 mm x 52 mm),sliding sash (42 mm x 67 mm ).Sliding mesh Sash (42 mm x 57 mm) Slide interlock (One vertical length in each shutters) (45.5 mmx 28 mm ),Glazing bead (24.5 mm x 16 mm) will be mitered cut and fusion welded at all corners, including railing of holes for fixing hardware and drainage of water etc. making arrangement for fising of hardware. EPDM gasket 1.2 + - 0.2mm thick galvanized steel frame (30mmx18 mm) 2 No.s ,sliding sash(30 mm x 18 mm),sliding mesh sash (26 mmx 10 mm) profile to be inserted in required profile, frame will be fixed to wall with 8 mmx100 mm long fasteners.HardwareTouch lock of zinc alloyed (white powder coated),steel roller system ,stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and required accessories. (Note:The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories.Net opening will be measured for payment purpose.) Area exceeding 2.00 Sqm Each

Providing and fixing factory made uPVC white colour sliding window three track made of extruded profiles with wall thickness of 2.3mm(+ - 0.2 mm). Window profile with hollow section with multi chamber.Frame (88 mm x 52 mm),sliding sash (42 mm x 67 mm ).Sliding mesh Sash (42 mm x 57 mm) Slide interlock (One vertical length in each shutters )(45.5 mmx 28 mm ),Glazing bead (24.5 mm x 16 mm) will be mitered cut and fusion welded at all corners,including railing of holes for fixing hardware and drainage of water etc. making arrangement for fising of hardware.EPDM gasket 1.2 + - 0.2mm thick galvanized steel frame (30mmx18 mm) 2 No.s ,sliding sash(30 mm x 18 mm),sliding mesh sash (26 mmx 10 mm) profile to be inserted in required profile ,frame will be fixed to wall with 8 mmx100 mm long fasteners.HardwareTouch lock of zinc alloyed (white powder coated ),steel roller system ,stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and required accessories .(Note:The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories.Net opening will be measured for payment purpose.)Area not exceeding 2.00 Sqm Each

M&L for 5.5 mm thick sheet glass ordinary quality and glazing with beading n exc 0.5 sqm in each pane complete all as specified and as directed.

M&L for 5.5 mm thick sheet glass ordinary quality and glazing with beading exc 0.5 sqm in each pane complete all as specified and as directed.

M&L for 5.5 mm thick frosted sheet glass ordinary quality and glazing with beading n exc 0.5 sqm in each pane complete all as specified and as directed.

S&F in repair 500 liters capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and directed.

S&F in repair 1000 litres capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and directed.

S&F in repair 20 mm dia Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipes and fixed complete all as specified and directed.

Taking up or down steel tubing and connection including cleaning for refixing or removal to store 20mm bore pipe complete all as specified and directed.

M&L for 20mm bore GI tubing medium grade with all fittings and fixed to walls/ ceiling or laid in floors complete all as specified and directed.

Taking down cement plaster on brick or stone walls or ceiling etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed..

Supply only Liquid water proofing compound of approved make complete all as specified and directed.

M&L for rendering 10mm thick in CM (1:6) on Brick/ Concrete surfaces of wall, finished surfaces even and fair complete all as specified and directed.

M&L for preparation of new plastered surface and applying two coat of oil bound distemper on walls over a coat of primer including 1 mm thick wall care putty complete all as specified and directed.

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for 1st quality non skid coloured ceramic Heavy duty parking tiles n exc 0.11 Sqm 10 mm thick set and jointed in neat cement slurry & pointed with coloured cement to match in floor over and including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

Excavation in trenches not exceeding 1.50 m in width and not exceeding 1.50m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying of cables etc. not exceeding 10 sqm on plan and not exceeding 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

M&L for soil filling under floors or in foundations including watering and consolidation from the material excavated in Sl item No. 32.

M&L for PCC 1:4:8 type D-2 as in foundation and mass concrete complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming in layers n exceeding 25 cm thick complete all as specified and directed

Removel of surplus soil to a distance n exc 50m and depositing where directed at a level n exc 1.5m above from the starting point complete all as specified and directed.

M&L for 15mm thick rendering on brick wall surfaces in CM 1:4 finished fair and even without using extra cement using WPC as per manufacturer instructions complete all as specified and directed. Note: (WPC will be measured and paid separately).

M&L for preparation of newly plastered surfaces of wall and applying two coats of white wash complete all as specified and directed.

M&L for surface excavation not exceeding 30 cm deep and averaging 18 cm deep and getting out in soil and loose soft complete all as specified and directed.

M&L for hardcore of broken stone or boulders of gauge not exceeding 63mm deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surfaces complete all as specified and direcetd.

M&L for 75 mm thick PCC 1:3:6 Type C-2 (using 40 mm graded aggregate) in floor sub base complete all specified and directed.

M&L for 25 mm thick PCC 1:2:4 Type B-1 (using 20 mm graded aggregate ) in floor finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as in coping & bed blocks etc. including necessary formwork if required complete all as specified and directed.

M&L for Precast reinforced cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in covers etc. complete all as specified and directed by Engineer-in-Charge.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for 100 mm thick cement concrete type-D-2, 1:4:8 using 40mm graded stone aggregate as in sub base complete all as specified and directed.

M&L for sand filling under floors or in foundations incl watering complete all as specified and direcetd

M&L for machine pressed precast conctete interlocking paver block with grey cement & pigment any shape and size confirming to IS 15658-2006, 80 mm thickness, M-40 Grade complete all as specified and direcetd

M&L for Coloured Non - skid Ceramic tiles 7 to 8 mm thick (400X400 square) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bedding in cement mortar (1:4) complete all as specified and as directed.

M&L for coloured Glazed ceramic tiles in vertical surface 450mm X 300mm X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and over and incl 10mm thick plaster in cement mortar (1:3) complete all as specified and directed.

M&L for use & waste of steel form work to soffits of suspended slabs such as roof slabs, floor slab, landing and similar work for flat rough finished surface complete all as specified and directed.

M&L for RCC M-25 grade (Design Mix) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like & similar RCC works all as specified and directed.

M&L for Sand stone slabs of thickness 10cm in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, etc. not exceeding 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4. complete all as specified and directed

S&F PVC solid factory made door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified and directed

S & F factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as shown in SSR Part – II 2004 and as directed by GE/Engineer-in-Charge

S&F 100 mm long butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed.

S&F 150mm Aluminium handles, cast type, anodised complete all as specified and directed.

S&F 200mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

M&L for 4.8 mm thick frosted sheet glass ordinary quality and glazing with beading n exc 0.5 sqm in each pane complete all as specified and as directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished fair & even complete all as specified and as directed.

M&L for preparing new plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:6) on other than fair faces of brick work ,finishing the surface even and fair complete all as specified and directed.

M&L for applying two coats of cement base paint over one coat of alkali resistant primer on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for cutting chases pinning in , making good to facing where reqd. and pointing in CM 1:3 to ends or edges of landing , steps, cills, sunshades,selfs lintels etc. and cutting chases for conceled for water tubing or conceled condute wiring etc and making good, cutting n.exc 10cm girth complete all as specified & as directed

S&F GI tube 15mm bore medium grade with all fittings fixed to walls and ceilings or laid in floor complete all as specified and directed.

S&F in repair Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including setting the trap and pan in concrete and including 10 ltr capacity PVC valveless syphonic action type low level flushing cistern and 32mm dia PVC Flush pipe complete including jointing to socket of flushing rim complete all as specified and as directed.

S&F 15 mm size angular cock, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed both end for iron pipes complete all as specified and as directed.

PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed.

S&F 15 mm size bib taps cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipes complete all as specified and as directed.

S&F vitreous china wash hand basin white flat back size 550 x 400 mm excluding taps waste chain and plug but including bracket, waste coupling complete all as specified and directed by Engineer-in-Charge.

S&F 32mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 and fittings, fixed complete to walls, ceilings or in floors etc. complete all as specified and as directed.

S&F 15 mm bore Pillar taps fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and direcetd.

S&F in repair 75 mm dia PVC (SWR) floor trap with CP grating including jointing with solvent cement all as specified.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F brass chromium plated shower rose 125 mm dia with shower arm and fixed complete all as specified and directed.

S&F 15 mm bore stop valve fancy type chromium plated with long cup and shank (Concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed

S&F brass chromium plated Tubular towel rail, 20mm dia, 'D' type, 60cm long between flanges including brackets fixed to wall complete all as specified and directed

S&F 110mm PVC (SWR) pipes single socketed, excluding fittings in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F 75mm PVC (SWR) pipes single socketed, excluding fittings in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F 110mm PVC (SWR) pipes single socketed, excluding fittings in any length with rubber ring joints, fixed to walls complete all as specified and directed

S&F 110mm PVC (SWR) bends any radius complete all as specified and as directed.

S&F 75mm PVC (SWR) bends any radius complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) junction single, (Single T) complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) junction single, (Single T) complete all as specified and as directed.

S&F 110mm PVC (SWR) vent cowl complete all as specified and as directed.

M&L for PCC 1:3:6 type C2 an in foundation of manhole and sewage pipe complete all as specified and as directed.

M&L for PCC 1:3:6 type C2 as in bed to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested for 100 mm bore complete all as specified and as directed.

M&L for 100 mm dia salt glazed stone ware drain pipes laid in trenches and jointed complete all as specified and as directed.

M&L for TMT bars 6 to 8mm dia, cut to length bend to shape reqd incl cranking and lbinding with mild steel wire (annealed) complete all as specified and as directed.

Cutting into existing manholes for connecting new drains of internal dia of pipe, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished and reforming benching as required complete all as specified and as directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M&L for laying in trenches GI pipe 25mm dia medium grade including all fittings and fixtures complete all as specified and directed.

S&F 20mm dia ball brass valves, high pressure with polythene float and flynut , screwed for iron pipe or brass ferrule and fixe complete all as specified and directed.

M&L for sand cushioning with dry local sand for cable protecting under ground cable (8 cm before laying the cable and 15cm after laying the cable) in trenches including punning the sand upto 18cm thick and consolidated complete all as specified and directed.

Supply and laying dry well burnt locally available brick sub class 'B' old size bricks laid flat with width equal to the length of whole bricks over cable protection complete all as specified and directed.

Supply and laying cable XLPE insulated screened PVC bedded galvanised steel strip or wire armoured, electric power cable(heavy duty) 1100Volts grade with stranded aluminium conductor of size 16 Sqmm 2 core complete all as specified and directed.

Supply and laying GI pipe light grade 40mm bore for cable protection including all fittings such as bend tee etc. complete all as specified and directed.

M&L for submain wiring with three RUNS of single core 4 sqmm stranded copper conductor FRLS PVC insulated cables for phase, neutral and earth drawn through and makeing good distrubed surface to match the existing surface including rigid PVC conduit ISI marked (not less than 20 mm dia) and all accessories and including concealed in wall and necessary cutting and chasing complete all as specified & directed. Note : Three run of 4 Sq mm single core for Phase /neutral/Earth wire and one run of PVC conduit will be measured as 1 RM unit.

M&L for point wiring in existing PVC/mild steel conduit with PVC insulated unsheathed, 1100 volts grade cable 1.5Sqmm (nominal area) FRLS type multi stranded copper conductor, single core drawn in existing PVC/mild steel for one light/fan/bell/ exhaust fan point controlled by one, one way switch on independent board including 3mm thick plastic laminated top cover sheet of required size of white colour, painting of existing pressed steel terminal box with a coat of black bituminous paint and 1.5 Sqmm FRLS type PVC insulated unsheathed cable multi-stranded copper conductor as continuous earth wire and connected to earth dolly as required at site & including chases cutting & making good disturbed surface & applying finishes to match existing surface complete all as specified and directed.

All as per item No. 100 above but one 5 pin, 5amp socket out let on independent board with 2.5 Sqmm cable multi-stranded copper conductor & 2.5 Sqmm cable FRLS type PVC insulated unsheathed cable multistranded copper conductor as continuous earth wire .

All as per item No. 100 above but one 5 pin, 15 Amps socket outlet on independent board with 2.5 Sqmm cable multi-stranded copper conductor & 2.5 Sq mm cable FRLS type PVC insulated unsheathed cable multi-stranded copper conductor as continuous earth wire.

S&F switch piano, single pole one way 5 Amps 240 Volt capacity flush type complete all as specified and directed.

S&F 3 pin 5 Amps socket outlet flush type complete all as specified and directed.

S&F switch piano, single pole one way 15 Amps 240 Volt capacity flush type complete all as specified and directed.

S&F socket outlet 2 in 1, 5 pin 5 and 15Amps flush type complete all as specified and directed.

S&F sheet metal enclosure for MCB (DB) double door type, single pole and neutral 4 way 240 Volts with 200Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB but with enclosure blank plates for unused way complete all as specified and directed.

S&F MCB, 6 to 32 Amps, SPN (single pole & neutral), 240 volt , 'C' curve, with rupturing capacity 10 KA , inculding providing thimble for out going cable complete all as specified and directed .

S&F MCB, 6 to 32 Amps, SP (single pole), 240 volt, 'C' curve, with rupturing capacity 10 KA, inculding providing thimble for out going cable complete all as specified and directed .

S&F for aesthetically designed LED linear mirror light fitting 1 x 09 watt, provided with high output PMMA diffuser for glare free light, decorative, environmental friendly, energy efficient complete with all accessories, prewired and making connection and in repairs, including 23/0.0076 flexible copper wire three core from connector to ceiling rose not more than 1.2 mtr, fixed on wall firmly complete all as specified and directed.

S&F for LED bulk head light fitting 10 W LED 600 Lumen enclosed in polycarbonate body, weather proof, LED lighting fixture with co extruded polycarbonate body, environmental friendly, energy efficient complete with all accessories, prewired and making connection and in repairs, including 23/0.0076 flexible copper wire three core from connector to ceiling rose not more than 1.2 mtr, fixed on wall firmly complete all as specified and directed.

S&F exhaust fan, 300mm sweep PVC body, single phase 240 Volts with all assessories including making hole on wall complete all as specified and directed.

S&F 1 X 18 W LED wall mounted tube light fitting, LED 6000K, Decorative ultra slim linear LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient complete with all accessories, prewired and making connection with and including flexible copper cable from ceiling rose to connector of required length including LED lamp complete all as specified and directed.

M&L for Earthing complete with steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized iron and steel earthwire protected by provision of GI medium grade pipe 15mm bore including provision of concrete pit made from PCC (1:2:4) type B-1(using 20mm graded stone aggregates) with 17mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 Kg/Sqm) and frame of angle iron 25 x 25 x 6mm with lugs 02 No and with 6mm dia MS bar handle made to shape, GI medium grade 20mm bore pipe for watering perforated at bottom, 1.75 metre long placed on top edge of earth plate, common salt & charcoal filling, test point made out of 17mm x 8mm FI with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No.5 of SSR Part-I connected to earth test point all as specified or indicated including testing on completion complete all as specified and directed.

M/S JAI DURGA CONSTRUCTION

Shivagya Engineering

Hi-Tech Constructions

vs construction

Vibha Enterprises