Construction of Barrack, Toilet Block, Remodeling of Corridor and Wire Mesh Fencing at State Hangar Building Campus, Hinoo, Ranchi For the Year 2023-24

Amount

Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I.

Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B)

Earth filling in foundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume)

Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Providing designation 75B brick work in C.M (1:6 ) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Providing designation 75 B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 125 mm thick reinforced designation 75A brick work in CM (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 25 including the cost of screening, carriage of materials, scaffolding , raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form forFoundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ)

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form forWeather shade, Chajjas, corbels etc., including edges

Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush door shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

providing Tor steel reinforcement of 10mm,12mm,16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.

(8mm dia )

(a) 10mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)}

(b) 12mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)})

Supplying fitting and fixing M.S.Grill made of 20x6mm M.S.flat as per approved design and drawing properly fabricated with joints continous fillet welded and finished smooth carriage of grill to work site,hoisting as per building specification and direction of E/I(where materials to not supplied by the deptt)

Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2mm at 100mm centers and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40 x 40 x 6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification and direction of E/I.

Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm .

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by the rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I.

Providing two coats of synthetic enamel paint of approved shade and make over new wooden surface including cleaning the surface after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface throughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement area shall be multiplied by the co-efficient as indicated in building specification)

Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing and fixing 18mm thick Gang saw cut mirror polished, pre molded and pre polish machine cut for platforms, vanity counters windows sills, facials etc of required size shade colour, texture over 20mm thick base cement mortar 1:4(1 cement:4 coarse sand) with joints treated with white cement ,mixed with matching pigment, epoxy touch ups ,including rubbing, curing etc. complete at all levels. Granite any colour,area of slab over 0.50sqmm

Providing edge moulding to 18mm thick marble stone counters venities etc.including maching polishing to edge to give hight gloss finish etc complete as per design approved by E/I.Granite work

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:15622 of (Thickness to be specifed by the manufacturer) of approved make in all colours shades except burgundy,bottle green,black of any size as approved by Engineer-in-charge in skirting,risers of steps and dados over 12mm thick bed of c ement mortar 1:3(1cement:3COARSE SAND) AND JOINTING WITH GREY CEMENT SLURRY @ 3.3KG PER SQM INCLUDING POINTING IN WHITE KCEMENT MIXED WITH PIGMENT OF MATCHING KSHADE COMPLETE. job as per direction of E/I

Providing fixing pressed steel door frame conferming to IS:4351 manufactured from commercial mild steel sheet of 1.25mm thickness including hinges,jamb,lock jamb,bead and if required angle threshold of mild steel angle section 50x25mm or base tiles of 1.25 mm pressed mild steel welded or rigidly fixed together by mechanical means adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards,lock strike plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as direction of E/I. Profile-B

Steel work in built up tubular ( round, square or rectangular hollow tubesetc.) trusses etc., including cutting, hoisting, fixing in position andapplying a priming coat of approved steel primer, including welding andbolted with special shaped washers etc. completeHot finished welded type tubes

Providing and fixing tiled false ceiling of approved materials of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in thegrid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 8 mm thick fully perforated calcium silicate board made with Calcareous & Smanufactured through autoclaving process to give stableiliceous materials reinforced with cellulose fibercrystalline structure with minimum compressive strength 225 kg/ sq. cm, bending strength 100 kg/sq. cm , of size 595x595mm, having perforation of dia. 10 mm with minimum perforatedarea 18 % with non woven tissue on the back side, having an NRC ( Noise Reduction Coefficient) of 0.85, with 50 mm thickrockwool of 48 kg /cum backing.

Providing and fixing 12.5mm thick fully perforated Gypsum Board dia made from plaster board having glass fibre conforming to IS: 2095 Part I of size 595x595mm including all complete job as per dierction of E/I

Providing and fixing precoated galvanised iron profile sheets (size,shape and pitch of corrugation as approved by Engineer-in-charge)0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 micronsepoxy primer on both side of the sheet and polyester top coat 15-18microns. Sheet should have protective guard film of 25 micronsminimum to avoid scratches during transportation and should besupplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tappingscrews of size (5.5x 55 mm) with EPDM seal, complete upto anypitch in horizontal/ vertical or curved surfaces, excluding the cost ofpurlins, rafters and trusses and including cutting to size and shapewherever required.

Providing and fixing precoated galvanised steel sheet roofing accesories iron profile sheets (size,shape and pitch of corrugation as approved by Engineer-in-charge)0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 micronsepoxy primer on both side of the sheet and polyester top coat 15-18microns.using self driling/selftapping screws complee Gutter (600mm over all girth)

Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete. E/I.

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20kg/ 10 sqm)

Providing and applying white cement based birla putty of average thickness 1mm of approved brand and manufacturer,over the plastered wall suface to prrepare the surface even and smooth complete.job as per direction of E/I.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanicallywherever required including cleat angle, Aluminium snap beading forglazing / paneling, C.P. brass / stainless steel screws, all complete as perarchitectural drawings and the directions of Engineer-in-charge. (Glazing,paneling and dash fasteners to be paid for separately) :Powder coated aluminium (minimum thickness of powdercoating 50 micron

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Polyester powder coated aluminium (minimum thickness of polyesster powder coating50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness

Filling the gap in between aluminium frame &adjacentR.C.C/Brick/stone work by providing weataher sillcon sealantover backer rod of approved quality as per architectural drawings and direction of E/I.Upto 5mm depth and 5mm width.

Supplying of 4mm thick ACP approved quality including all complete job as per direction of E/I.

ProvProviding and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. completeiding and fixing bright finished brass handles with screws etc.compelte. (125mm)

Supply of stainless steel wire guage (Grade-304) aperture 1.4mm and 0.50mm dia wire including all complete job as per direction of E/I.

Dismantling patent stone floor including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Providing and laying vitrified Paring / Industrial tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 4457:2007, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 300x300 x 10 mm sizes.

Providing 250mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

Providing and laying factory made coloured chamfered edge CementConcrete paver blocks of required strength, thickness & size/shape, madeby table vibratory method using PU mould, laid in required colour & patternover 50mm thick compacted bed of fine sand, compacting and properembedding/laying of inter locking paver blocks into the sand bedding layerthrough vibratory compaction by using plate vibrator, filling the joints withjamuna sand and cutting of paver blocks as per required size and pattern,finishing and sweeping extra sand in footpath, parks, lawns, drive ways orlight traffic parking etc. complete as per manufacturer’s specifications &direction of Engineerin-Charge. 60mm thick C.C. paver block of M-35grade with approved colour, design & pattern.

Supplying and installation of moisture resistant/fire resistant cement board as per standard sizes fixed with sell drilling/taping screws,screws shall be of counter sunk rib head of 1.60mm to 4mm thick or 8 to 10 guage of length varying from 25 to 45mm .Cement Fiber Boared 6mm thick as per IS 14862-2000 of type B(High pressure steam cured) including all complete job.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing apes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with12.5 mm thick tapered edge gypsum moisture resistant board

Providing welded mesh(8 to 10 SWG) 100 to 125mm square size including all complete job as per direction of E/I.

Labour for fitting & fixing G.I. woven wire fencing including fixing of post in cement concrete at 2.5 M centres including cost of staples (but excluding the cost of cement concrete angle iron post ,its cutting and making holes,nuts and bolts) all complete as per building specification and direction of E/I.

Providing and fixing stanless steel(Grade 304) railing made of Hollow tubes,channells,plates etcincluding welding,grinding,buffing,polishing and making curvature( wherever required) and fitting the same with necessary stainless steel nuts and bolts complete,I/C fixing the railing with necessary accessories & stainless steel dash fasteners,stainless steel bolts etc,of required sizie,onthe top of the floor or the side of waist slab with suitable arrangment as per approval of Engineer-incharge,(for payment purpose only weight of stainless steel members shall be considered excluding fixing accessoreis such as nuts,bolts,fastners etc)

Carriage of materials from nearest approved sources of supply including loading into trucks and unloading from trucks and stacking properly at work site as directed by the E/I.

Brick lead 8K.M(1K+7P)

sand lead 8K.M.

chips lead 22K.M.

Stone Metal 20 km lead

local sand lead 3K.M

Providing and fixing male ended 15 mm dia brass bib cock of approved quality ( wt not less than 350 gms ) with extra socket all complete as per specification and direction of E/l .

Providing and fixing brass / C.I. Stop cock of approved quality all complete as per specification and direction of E/l . A) BRASS STOP COCK

(b) 20 mm dia

Providing and fixing N.P/C.P brass/P.V.C porcelain shower rose of 15mm inlet etc. all complete as per specification and direction of E/l (A) C.P. SHOWER

(b) 125 mm dia.C.P. SHOWER

Providing and fixing Gun metal full way valve of approved qualtiy, all complete as per specification and direction of E/l

(a) 15 mm dia wt not less than 300 gms

(a) 20mm dia wt not less than 400 gms

Making holes in walls for laying G.I pipes and restoring the same after pipe laying as per specification and direction of E/l

(b) 250 mm thick wall.

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/l. (a) Glass shelf with C.P brass rail

1) 600x125 mm glass shelf complete

(b) Mirrors of 6mm thick plate glass bevelled edge mirror including C.P brass revolving fittings, 3 mm plywood board and C P hinges to fix with mirror (1) 600x450 mm size

( c) C.P brass towel rail 20 mm x 600 mm with bracket container

(2) C.P brass shop dish container medium quality with screw and hinges etc.

Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of Parry Hindustan or any other I.S.S. approved make with 100 mm H.C.I., "p" trap 15 litres C.I.. or C. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32 mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.

(a) 580mm longwith 10.0 lit. low level P.V.C. cistern

Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.

(b)10/12.5lit. low level P.V.C. cistern

Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed c.l. or R.S. brackets 32m C.I. brass waste 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms., 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/l.

Providing and fixing white vitreous china pedestal for wash basin completelyrecessed at the back for the reception of pipes and fitting including all complete job as per direction of E/I.

Earth work in excavation for laying of different types and sizes of R.C.C. spun pipes with disposal of excavated earth within initial lead and lift as per specification and direction of E/l.

(a) For classification of soil item- A

Labour for laying, fitting and fixing NP2 R.C.C. spun pipe with collars in lines, level and grade and providing approved jointing materials and joints properly filled to make them leak proof including providing sight rails, bonning rod, night guard, red light and barrier etc. all complete as per specification and direction of E/l.

150 mm dia R.C.C. spun pipe Upto 3.0 meter depth of invert below G.L.

Supplying materials and labours for constructing inspection chamber of designation class 75 B bricks size 750 mm deep, 600 x 450 internal dimension having 250 mm wall thickness in cement mortar ( 1:6 ) including 12 mm cement plaster ( 1:4 ) with punning on inside and cement plaster (1:6 ) with 600 x 475 mm G.I. cover with frame (Weight not less than 36 Kg.) in foundation and refilling all complete as per specification and direction of E/l.

Supply of NP2 R.C.C.Hume pipe with collour including allcomplete job as per direction of E/I.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion(i)single socketed pipes.

75mm dia

110mm diameter

Providing and fixing on wall face unplasticised PVC moulded fittings, accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring confirming to I:5382 leaving 10mm gap for thermal expansion.

Single Tee with door 75x75x75mm

Single Tee with door 110x110x100mm

Single Tee with out door 75x75x75mm

Single Tee with out door 110x110x100mm

Bend 75mm dia

Bend 110mm

Providing and fixing Chlorinated polyvinyl chloride (CPVC)pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i.e. fixing the pipe with clamps at 1.m.spacing.This included jointing of the pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. concealed work including cutting chases and making good the walls etc.(Internal work)(Exposed on wall)

20mm nominal outer dia pipes

25mm nominal outer dia pipes

Providing and fixing stainless steel A ISI 304(18/8) kitchn sink with drain board as per IS 13983 with C.I. brackets and stainless steel plug 40mm including painting of fittings and brackets ,cutting and making good the walls wherever required(610x460x200mm)

Providing and fixing 8mm dia C.P/S.S.Jetwith flexible tube upto1meter long with S.S.triangular plaate to Eureopean tyhpe W.C.approved quality and make as approved by E./I.

Providing and fixing Chlorinated polyvinyl chloride (CPVC)pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i.e. fixing the pipe with clamps at 1.m.spacing.This included jointing of the pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. concealed work including cutting chases and making good the walls etc.(Internal work)(Concealeld work)

15mm nominal outer dia pipes

20mm dianominal outer dia pipes

Providing and placing on terrace(at all floor levels) polyethylene water storage tank ISI 12701 marketed with cover and suitable locking arrangement and making necessary holes for inlet ,outlet and overflow pipes but without fillings and the base supported for tank.

Providing and fixingPTMT Grating of appoved quality and colour

C.P.Gratings circular type-125 mm dia

Making soak pit 2.5m diameter 3.0metre deep with 45x45cm dry brick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100mm diameter,1.8m long complete as per standard design .with F.P..S.Bricks.

Wiring for light/fan point/exhaust fan point/call bell Point with 1.5 sq.mm FRPVC insulated copper Conductor single core cable in surface/recessed PVC conduct with Modular type switchmodular plate, Suitable size G.I Box etc. as required.

group C

Wiring for light / Power plug with 2×4 sq mm FRPVC in insulated copper conductor single core cable in surface / recessed PVC conduit along with 1 nos 4 sqmm. FR PVC insulated copper conductor single core cable for loop earthing as required .

Wiring for circuit/submain wiring along with wiring with the following sizes PVC insulated copper conductor, single core cable in surface/recessed PVC conduit as required.

2x1.5sqmm+1x1.5sqmm earth wire

2x2.5sqmm+1x2.5sqmm earth wire

4x10sqmm+2x10sqmm earth wire

S/F Modular type switch/socket supplying and fixing following modular type switch/socket on the existing modular plate and switch box including connections but excluding modular plaate etc as reqd.

5/6 Amps 3pin 5/6 Amp socket

15/16 amps,one way switch

5/6 amps,3 socket outlet

15/16amps,6pin socket outlet

S/F Modular type electronic fan regularor_Supplying and fixing stepped type fan regulator on the existing modular plate swith box including connections but excluding modulalr plate etcas required.

S/F Suitable size G.I.Box on surface/Recess with suitable size ofr phenolic laminated sheet cover in front including providing 3pin 5/6 Amp socket outlet and 5/6 amp. Piano type switch connection as painting etc. as req.

S/F Suitable size G.I.Box on surface/Recess with suitable size ofr phenolic laminated sheet cover in front including providing 6 pin 15/16 Amp socket outlet and 15/16 amp. Piano type switch connection as painting etc. as req.

S/F 2 Pin 5 Amp ceiling rose on the existing junction Box wooden block incuidng connection etc as reqd

S/F Brass batton / Angle Holder including connection etc as reqd

I.T.C.of exhaust Fan up to 450mm sweep in the existing 0pening including making the hole to suit the size of the above fan making good the damage connection testing commissioning etc. as reqd.

S/F the following way SP & N sheet steel M.C.B. D.B. 240 V on surface/recess complete with tinned copper busbar neutral bus bar earth plate dinbar hinged front acrylic cover from MCB knob datachable gland plate inter connection phosphatied and powder painted including earthing etc as required ( without MCB/RCCB/Insolator)

12 way,Double door

S/F”C” series SPMCB: supplying and fixing 6 amps to 32amps rating,240 volts ,10KA,"C" curve, ,miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections ,testing and commissioning etc as required.

6/32 amps , single pole

40 amps,DP

Supplying and fixing 20 amps,240 volts,SPN industrial type,socket outlet,with2 pole and earth,metal inclosed plug ,top along with 20 amps,"C" curve,SP,MCB, in sheet steel enclosure,on surface or in recess,with chained metal cover for the socket out let and complete with connections,testing and commissioning etc as required.

S.I.T.C of floowing rating LEDstreet lighting luminate with pressure die cast housing and toughenee glass cover(IP 66 protection) in existing pole/pipe for supply voltage 100-270V AC.50Hz Luminarie shall be confirm to IS:10322 Part 5/section-3 and shall be complete with all neccssary accessories as required

45/48W LED Street light

Supply Installation,testing and commissioning of follwing size ceiling fan 3 Bleades confirming to IS:374:2019 including wiring the down rods of standard length(upto 30cm) with 1.5 sqmm FR PVC insulated ,copper wire suitable for 230V 50Hz,single phase supply etc.complete as required.

1200mm(48")BI DC 5 star rating 32W ceiling Fan

S.I.T.C of floowing rating surface mounted LED tube light fitting suitable for 230 V 50Hz,single phase supply etc.complete as required.

20/32 W LED Tube light

Supply and fixing 15/16 watt LED Bulb including all complete job as per direction of E/I.

Supply of metal Exaust Fan 12"(300mm) including all complete job as per direction of E/I.

Supply of wall mounted Fan 16"(400mm) including all complete job as per direction of E/I.

Add 18 % GST (in Basic Rate must fill 12)

Add 1% Labour Cess (in Basic Rate must fill 1)

Ms Gokul Construction