138WE/L-177/2025-26

Demolition of cement concrete (un reinforced ) in ground floors and pavings not exc 15cm thick (below or above ground level) and removing debris off the premises complete all as specified and as directed by Engr-in-Charge.

Dismantling wall and ceiling boards (Fiber, pulp, insulation, blankets etc.) any thickness including covered fillets and supporting members, complete all as specified and/or directed by Engr-in-Charge.

Dismantling unframed wooden fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling etc. under 40 sqcm in section, complete all as specified and/or directed by Engr-in-Charge.

Demolition of precast cement concrete block walling built in cement mortar including all quoins, arches, pillars etc. complete all as specified and/or directed by Engr-in-Charge.

Dismantling plain or corrugated steel/fibre sheeting any gauge or thickness including nanital or similar pattern complete all as specified and as directed by Engr-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for angle iron or flat iron as in post and guard bars or grating, complete all as specified and/or directed by Engr-in-Charge.

M&L for 9mm thick prelaminated particle board medium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with screws to timber frame work as in wall panelling, shelves/boarding complete all as specified and as directed.

M&L for 9mm thick prelaminated particle board medium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with screws to timber frame work as in ceiling, complete all as specified and as directed.

M&L for 2nd class soft wood clean sawn as in battens for grids of ceiling & lining fixed with nails exc 13 sqcm and not exc 25 sqcm in section, complete all as specified and directed by Engr-in-Charge

M&L for 2nd class soft wood clean sawn as in beading for edges of ceiling, lining or wooden flooring work fixed with nails exc 6 sqcm and not exc 13 sqcm in section, complete all as specified and/or as directed by Engr-in-Charge.

M&L for forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound Grade 'A' in plinth protection, complete all as specified and/or as directed by Engr-in-Charge.

M&L for PCC 1:4:8, type D2 (using 40mm graded crushed aggregate) as in mass concrete and filling of foundation, complete all as specified and/or as directed by Engr-in-Charge.

M&L for precast solid blocks in cement concrete 1:3:6 type C-1 (20mm graded crushed stone aggregate) as in block masonry, exc.10cm in width and set in cement mortar 1:6, complete all as specified and/or directed by Engr-in-Charge.

Supply only integral liquid water proofing compound. Make : Pidilite/Sika/Asian paints.

S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and/or as directed by Engr-in-Charge.

S&F 35mm thick 2nd class hard wood plain framed panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, complete all as specified and/or as directed by Engr-in-Charge.

and/or as directed by Engr-in-Charge.

M&L for preparation of old treated wood or wooden based surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and/or as directed by Engr-in-Charge.

M&L for machine cut kota stone slab flooring 20-25mm thick over and including cement screed bed 20mm thick in cement mortar 1:6, set and jointed in neat cement slurry, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and/or as directed by Engr-in-Charge.

M&L for preparation new steel surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed

M&L for form work to soffits of suspended slabs, flat type such as roof, floor slabs, landings etc not exc. 200mm thick (horizontal or sloping), rough finished concrete surfaces, complete all as specified and/or as directed by Engr-in-Charge.

M&L for reinforced cement concrete 1:2:4, type B1 (20 mm graded stone crushed aggregate) nominal mix as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs etc. complete all as specified and/or as directed by Engr-in-Charge.

S&F in repair 19mm dia mild steel, chromium plated curtain rods, with brackets, end bulbs, complete all as specified and/or as directed by Engr-in-Charge.

S&F mild steel rolled sections in main and cross beams, hip and jack rafters; purlins where connected to common rafters running rails and guids for sliding doors; fixed with angle cleats or other connecting plates and similar work conforming to Fe-290, Gde-E-165, complete all as specified and/or as directed by Engr-in-Charge.

M&L for preparation of old steel surface of any description over 10cm in width or girth and applying two coats of synthetic enamel paint, complete all as specified and/or as directed by Engr-in-Charge.

Point wiring complete with 1.5 sqmm nominal area of copper conductor multi stranded PVC insulated and unsheathed 1100 volts FRLS cable drawn through & including PVC casing & caping with standard accessories such as elbows, tees, junctions etc. and PVC moulded terminal box with top cover of including PVC insulated unsheathed solid 1.5 sqmm copper conductor FRLS cable as continuous earth lead all as specified and directed for the following:-

One light point controlled by one way switch.

One switch socket outlet 6 Amps, 230 volts point on independent board.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth for laying of pipe, cables etc. and getting out in soft / loose soil, complete all as specified and directed.

Removing surplus soil to a distance not exc. 50m and depositing where directed at a level not exceeding 1.5 Mtr above the starting point complete all as specified and directed.

Material & labour for sand cushioning with clean dry sand to cables with layer of sand 8 cm before laying of cable and 15 cm thick after laying of cable complete all as specified. Note : For payment purpose punned thickness of 18 cm shall be measured against spread thickness of 23 cm as mentioned in para 19.75 of SSR part-I.

Material & labour for providing PCC cable cover class LV type-I of size 250x150x40mm laid in perpendicular to the cable abutting each other all as specified and directed at site.

Supply & laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volt grade of cross sectional area 70 Sqmm 3.5 Core complete all as specified and directed.

Supply & laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volt grade of cross sectional area 50 Sqmm 3.5 Core complete all as specified and directed.

Supply & laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volt grade of cross sectional area 120 Sqmm 3.5 Core complete all as specified and directed.

Supply and fix in replacement on load change over of 160 A with enclosure complete all as specified and directed.

M&L for PCC 1:2:4, type B1 (using 20mm graded crushed aggregate) as in mass concrete and filling of foundation, complete all as specified and/or as directed by Engr-in-Charge.