Renovation/Repair of District ATMA Offices at Kokrajhar,Dhubri and Goalpara

Amount

ATMA GOALPARA:Civil Works: Dismantling all types of corrugated/ trapezoidal sheet roofing including ridges, hips, valleys and gutters etc. and stacking the materials as directed by the department for all levels

Dismantling wood work in frames, trusses, purlins and rafters including stacking the materials as directed by the department for all levels.

Dismantling all types of ceiling, partition and wall lining and stacking the materials as directed by the department for all levels

Dismantling and removing the existing door and window frame (chowkath) both wooden and steel of different sizes without damaging the walls and removing the frame and necessary repairs to the edges of the walls as directed for all levels. (ii) Area of door/window above 3.00 m2

Demolishing RCC work including stacking of steel bars and disposal of unserviceable material as directed for all levels

Demolishing brickwork including stacking of serviceable materials and disposal of unserviceable materials as directed for all levels

Demolishing CC floors of various thickness including top layer and base course and disposal of debris as directed for all levels.

Earth work in excavation for foundation for trenches of walls ,retaining walls, footing of column, steps, septic tank etc. including refilling A) Upto a depth of 2.00m below the existing ground level (a) In ordinary Soil

Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. A) Brick on flat soiling

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In proportion 1 Cement : 4 Sand : 8 Coarse agg. by volume

Plain cement concrete floor base in prop. 1:3:6 laid in alternate bays as Specified with coarse aggregate of sizes 13mm to 32mm including dewatering if necessary and quring etc. complete

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level)

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) (i) Using mixture machine (A) In Sub-structure upto plinth level (b) M20 grade concrete or Prop. 1:1.5:3

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) (i) Using mixture machine (A) In Super-structure from plinth level upto 1st floor level (b) M20 grade concrete or Prop. 1:1.5:3

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in:Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc.(b) Using 25mm thick plank

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Sides of Tie beam, grade beams etc. at or below ground level (a) Using 25mm thick plank

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in:Columns, Pillars, Posts & Strut(a) Square, Rectangular, polygonal in plan or any shape like Tee/L etc. having plane vertical face(ii) Using 25mm thick plank

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in:Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties.(a) For depth not exceeding 1.0M.(ii) Using 25mm thick plank

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in:Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like.(a) Floors etc. upto 200mm in thickness.(ii) Using 25mm thick plank

Brick work in cement mortar with 1st class brick including racking out joints and dewatering if necessary and curing complete as directed in Prop. 1:4 in sub-structure upto plinth level

Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary. (c) With river sand or silt (Predominantly non plastic) by truck carriage including loading & unloading

Providing and laying 25mm thick damp proof course with cement concrete in prop 1:1.5:3 with graded stone agg. of 10mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacturer including curing etc. complete as directed.

Providing wood work in frame (chowkaths) of doors, windows, clerestory windows and other similar works wrought, framed and fixed in position in contact with C.C or brick masonry wall including supplying, fitting and fixing with M.S. hold fast (40mmx3mmx250mm) as per design embeded in cement concrete block in proportion 1:2:4 and with two coats of kiricide oiling to the timber faces in contact with C.C and masonry as directed and specified. (a) With Sal Wood

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) (A) 112mm thick brick wall a) In cement morter in proportion 1 : 4

Providing fitting, hoisting and fixing of roof trusses including purlins fabricated using MS circular hollow section conforming to relevant I.S. code, as per approved design and drawings including providing M.S. cleats, base plates, bolts and nuts and one coat of red oxide Zinc Chromate primer and two coats of approved enamel paints complete including fitting necessary cleats etc. for fixing ceiling joists as per design and drawing as directed.

Providing corrugated galvenised Iron sheet roofing of TATA SHAKTEE / SAIL including fitting and fixing necessary galvenised J or L hooks, bolts and nuts 8 mm dia with bitumen washer 25 mm dia x 3 mm thick and 1.6 mm thick limpet washer complete excluding cost of roof truss, purlin etc. (Roof trusses and purlin etc.to be measured and paid separately). (d) 0.60 mm thick

Providing galvd iron ridging of TATA SHAKTEE / SAIL including supplying and fixing necessary galvd screws/washers etc. complete as directed.(d) 0.60 mm thick (ii) 230 mm lapping

Providing, fitting and fixing full panelled doors/ windows including oxidised M.S butt hinges (100mm x75 mm x3.55mm) with necessary screws (other fittings to be measured and paid separately ) B) With 1st class local wood (i) 40 mm thick.

Providing, fitting and fixing anodised aluminium sliding windows and ventilators of standard sections of approved brand without horizontal glazing bars, joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handles, angle cleat, rubber gasket, roller, bolting device, locking arrangements, screws etc as required complete as specified and directed for all levels. (b) 3 track sliding window

Providing and fixing M.S. grill of required pattern for windows / C.S windows / opening with M.S. flats at required spacing 1) Plain grill (a) Fixed to wooden frames.

65mm thick cement concreate floor consisting of 50mm under layer of cement concrete in proportion 1:3:6 (1 cement : 3 coarse sand : 6 coarse agg.) and 15mm thick wearing layer in cement conreate proportion 1:1:2 laid in panels and finished with a floating coat of neat cement finish including curing etc. completed as directed

Supplying, fitting and fixing ceiling tiles of 10mm thick made from Duratuff medium density fibre board in size 1200mm x 1200mm x 10mm with Sal wood timber frame (to be measured and paid separately)leaving an expansion gap of 3mm with necessary nails, screws etc. including 1st class local wood (Hollock /Bonsum / Sundi etc.)beading of size 50mm x 12mm complete as directed and specified.

Providing barge board of size 200mm x 20mm with 1st class local Hollock/ Bonsum timber including fitting and fixing with necessary wood screws etc. complete.

Providing wood work in frame of false ceiling partitions etc.sawn, wrought, framed hoisted and fixed in positon with spikes, nails, M.S flat,angle/ cleats with bolt and nuts complete including kiricide oiling two coats to unexposed surfaces of the timber (M.S flats, angle cleats, and bolt and nuts required for flat, angle cleats wherever necessary shall be measured and paid separately) (a) With Sal Wood

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side b) In cement mortar 1:5

Cement plaster skirting with cement mortar in prop. 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement including rounding of junctions with floor.(b) 15 mm thick

Providing Ceramic Tiles of approved quality, size, shape and thickness not less than 8 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with fix-A Tile Choksey/ Sika/ Pedelite/ Rouf/ White cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed (coloured pigment should be in conformity with colour of slab and as approved and directed by the Department). a) Normal range ( Somany / Orient / Nitco / Asian Make )(i) Of size 300mm X 300mm and above

Providing polished ceramic wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Walls means both interior and exterior walls). (a) Normal range(i) Of size 300mm X 300mm and above

Applying priming coat over new wood and wood based surfaces over 100mm in girth/width after and including preparing the surface by throughly cleaning oil, grease, dirt snd other foreign matter , sand papering and knotting. (a). With ready mixed paint , Wood primer ( White )

Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matter sand papering and stopping.(i).Surfaces over 100mm in width or girth.a). General purpose (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

b) Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on new wall surface (two coats) to give an even shade after throughly brooming the surfaces to remove all dirt and remains of loose powdered materials.

Providing surface preparation for walls, celling etc.using average 1.50 mm thick plaster of paris including clearing, rubbing with sand paper, filling gaps, depression etc. where necessary, with chalk powder and and plaster of paris paste, making the surface even and smooth complete at all levels as specified and directed.

Wall painting (two coats) with acrylic emulsion paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth.

Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished ) a) Sliding door bolts i) 300mm x 16mm

Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished )b) Tower bolts ii) 250mm x 12mm

Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished )b) Tower boltsc) Door handles iii) 150mm

ELECTRICAL WORKS: Wiring for light/ fan/ call bell point with 2x1.5 sq mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) with flat 19 mm ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in surface system, including 6 Amp flush type switch/ bell push (Anchor Penta/Gold medal /Kolor kany.Kom/ Havells or equivalent make as approved by the Deptt.) GI/ MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover ,ceiling rose (Anchor/Gold medal /Kolor kany.Kom / Havells or equivalent make as approved by the Deptt.) etc. complete as directed and specified by the Deptt. Short point up to 3.00 metre. length.

Wiring for light/ fan/ call bell point with 2x1.5 sq mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) with flat 19 mm ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in surface system, including 6 Amp flush type switch/ bell push (Anchor Penta/Gold medal /Kolor kany.Kom/ Havells or equivalent make as approved by the Deptt.) GI/ MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover ,ceiling rose (Anchor/Gold medal /Kolor kany.Kom / Havells or equivalent make as approved by the Deptt.) etc. complete as directed and specified by the Deptt. Medium point up to 6.00 metre. Length.

Wiring for light/ fan/ call bell point with 2x1.5 sq mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) with flat 19 mm ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in surface system, including 6 Amp flush type switch/ bell push (Anchor Penta/Gold medal /Kolor kany.Kom/ Havells or equivalent make as approved by the Deptt.) GI/ MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover ,ceiling rose (Anchor/Gold medal /Kolor kany.Kom / Havells or equivalent make as approved by the Deptt.) etc. complete as directed and specified by the Deptt. Long point up to 10.00 metre. Length.

Wiring for 5 pin 6 amp plug with 1.5 sq mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) including providing & fixing 5 pin 6 amp socket outlet (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) and 6 amp flush type switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) earthing the 3rd pin of the socket as required on the switch board in flat ISI marked casing 'n' capping system, when fitted on same board of light and fan. Medium point up to 6.00 metre. Length.

Wiring for 5 pin 6 amp plug with 1.5 sq mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) including providing & fixing 5 pin 6 amp socket outlet (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) and 6 amp flush type switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) earthing the 3rd pin of the socket as required on the switch board in flat ISI marked casing 'n' capping system, when fitted on same board of light and fan. Long point up to 10.00 metre. Length.

Wiring to 5 a pin including providing and fixing 5 pin 6 Amps flaush type socket out let 6 Amps flush type (ISI marked) and Iron lad switch board phenolic laminated sheet cover including earth continuty with 2.5 Sqm PVC insulated unhealthed copper wire to the third pin and painting etc. as required Medium point up to 6.00 metre. Length.

Wiring to 5 a pin including providing and fixing 5 pin 6 Amps flaush type socket out let 6 Amps flush type (ISI marked) and Iron lad switch board phenolic laminated sheet cover including earth continuty with 2.5 Sqm PVC insulated unhealthed copper wire to the third pin and painting etc. as required Long point upto 10.00 m length

Wiring Sub main line with PVC insulated single core copper conductor cable complete as directed With 2 X 2.5 Sq. mm + 1 X 2.5 Sq. mm PVC insulated

Wiring Sub main line with PVC insulated single core copper conductor cable complete as directed With 2 X 6 Sq. mm + 1 X 2.5 Sq. mm PVC insulated

Supplying and fixing brass batten holder including connection etc. complete as directed

Supplying and fixing of 11/15 Watt CFL lamp in existing brass baten holder etc.

Providing and fixing ICTP and N link main switch of 240 volt. Grade including drilling board / Iron frame and fixing with bolt and nuts and connection etc. compete a / 30 / Am capacity and P.N.B

Installation of Earth station with 40mm dia and 4.5 mtr. Long G.I. Pipe with necessary G.I reducing socket 40mm X 20mm size ect. Compplete as directed

Extra for using salt (5 Kg) and charocol 64 Kg for pipe Earth electrode as required

Do with 6 SWG G.I Earthwire

Supplying including fitting fixing of high speed A.C celling fan complete as directed

Supllying with fiting and fixing Sheet Steel Phosphates, Pawder painted double door surface mounting, horizental TPN MCB DB incorporated with bas-bar neutral link, earth bar and din rail etc. as directed by the Deptt. a) 20 A Capacity

Supplying, installation, testing and commissioning of the following prewired CFL / Fluorescent luminaries complete with all accessories such as ballast, starter etc directly on wall / ceiling including connection with 1.5 Sq. mm PVC insulated single core copper conductor as required and as directed by the depptt.

Load security, meter security etc. to be paid LAEDCL (Proposed connected load 2 KW)

SANITARY & WATER SUPPLY WORKS: Providing and fitting fixing vitreous china flat back type hipped front urnal basin with standrad flash pipe and CP brass spreader and brass union etc. (A) Parry ware make(a) White(iv) Flat back (Cat. No. C0501 / 72)

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia.

Supplying fiting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.a) In exposed surfaces or in trenches. (i) 160mm dia

Supplying, fitting and fixing PVC single Tee with door of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels a) In exposed surfaces or in trenches. (i) 100mm dia

Supplying, fitting and fixing PVC reducer of (Supreme / Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels a) In exposed surfaces or in trenches. (i) 110mm X 63mm

Filling sunken floor with broken jhama brick bats and sand including compacting and supplying of materials complete as specified and directed for all levels.

ATMA DHUBRI: CIVIL WORKS: 25 mm thick cement concrete topping 1:2:4 (1cement : 2 coarse sand : 4 coarse aggregate of 12 mm nominal size) finished with a floating coat of neat cement finish (base concrete to be measured and paid separately) to be laid in panels including curing complete as directed.

Providing, fitting and fixing PVC Door shutters of 37mm (single panel seamless finish) of Syntex make, at all levels made of extruded sections in the configuration of 'A'.The overall dimension is 37mm x 90mm, with usual process variation having a wall thickness of 2mm with a variation of +0.03mm provided with all plastic reinforcement to avoid rusting. The shutter frame is mitred and joined at the corners by means of stainless steel screws.The corners of the shutter frame are being reinforced by polymeric reinforcement of the size 125mm x 250mm and the lock rail is reinforced by 45 x18 x255 size reinforcement.The lock rail is made of extruded hollow PVC section in the configuratino of 'H' having wall thickness of 2mm with a variation of +0.03mm and effective dimension of 37mm x 105mm. The infill is made of multi-chambered hollow PVC extruded panel having an effective dimension of 762mm x 20mm or less as per requirement with usual process variation having a wall thickness of 1mm +0.03mm.The entire door shutter should be provided with S.S. screws at appropriate places for rust free quality. (Door fixtures and fittings to be measured and paid seperately.)

Providing fitting and fixing anodised aluminium sliding windows and ventil ato rs of standard sections of approved brand (HINDANCO /NALCO /BALCO/ JINDAL /Other equivalent primary producer)Without horizontal glazing bars,joints mitred and welded (manufactured to relevant I.S specifications)and providing and fixing handles,angle cleat, rubber gasket,roller,bolting device,locking arrangements,screws etc. as required comp lete as specified and directed for all levels. b) 3 track sliding window i) 6mm clear glass

Providing fitting and fixing anodised aluminium sliding windows and ventil ato rs of standard sections of approved brand (HINDANCO /NALCO /BALCO/ JINDAL /Other equivalent primary producer)Without horizontal glazing bars,joints mitred and welded (manufactured to relevant I.S specifications)and providing and fixing handles,angle cleat, rubber gasket,roller,bolting device,locking arrangements,screws etc. as required comp lete as specified and directed for all levels. a) 2 track sliding window i) 6mm clear glass

Providing fitting and fixing anodised aluminium windows and ventil ato rs of standard sections of approved brand (HINDANCO /NALCO /BALCO/ JINDAL /Other equivalent primary producer)Without horizontal glazing bars,joints mitred and welded (manufactured to relevant I.S specifications)fitted with 6mmx3.15mm lugs 100mm long CC blocks 150mmx100mmx100mm in 1:3:6 mix including providing and fixind handles,frictions stys joining cleat bolting device,locking arrangements,spring catch as required complete as specified and directed for all levels,(cement conc.to be measured and paid separately. a) Side hung and top hungs window and ventilators i) 6mm clear glass

Providing, fitting and fixing factory made Santro Flush door shutters having core & cross bands fabricated from seasoned 1st class timber, 25mm core battens, 2.5mm to 3.5mm uniformly thick cross bands, styles & rails made from hardwood timber of width not less than 50mm, fixed to the door frames (chowkath) with necessary hinges, screws, bolts etc. as specified and directed at all levels (Door fixtures and fittings to be measured and paid seperately.) (ii) 35 mm thick.

Providing, fitting and fixing M.S. grill of required pattern for windows/ clerestory windows/ opening with M.S. flats at required spacing in frame all round, squre or roundM.S.bars with round headed bolts and nuts or screws. II. Ornamental grill (c) Fixed to Brickwork/P.C.C/R.C.C.

Providing anti-skid Tiles of approved quality size, shape and thickness not less than 8mm on floors, skirtings over a cement mortar bed 15mm thick of 1:3 (1cement : 3 coarse sand)approved make fix with Fix-A tiles (Choksey/Sika/Rouf/Pedelite)/White Cement mixed with approved pigment to match shade of tiles complete at all levels as specified and directed (B) VITRIFIED iii) Executive Range-1(Size 600mmx600mm and above. i) Nitco made b) Imperia series

Providing polished ceramic wall tiles of approved quality,size,shape and thickness not less than 8 mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand) including cutting where necessary finished with flush pointing with FIX-A-Tile(Choksey/Sika/Pedelite /Rouf)/white cement slurry mixed with approved pigments to match shade of tiles complete at all levels as specified and directed.(Cement plastering to be measured and paid separately).( Coloured pigment should be in conformity with colour of tiles and as approved and directedby the Department).(walls means both interrior and exterior walls) .b) Executive range Somani/Nitco i) (sizes 200mm x 300mm and above)

Providing VITRIFIED floor tiles of specified size, shape and thickness not less than 8 mm on floor, skirtings, risers and treads of steps over 15 mm thick cement mortar inprop 1:3 (1cement:3coarse sand) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/ Sika/ Pedelite/ Rouf)White cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). a) Normal range Somani/Orient/Nitco/Varmora ii) (sizes 600mm x 600mm and above)

Providing surface preparation for walls, celling etc.using average 1.50 mm thick plaster of paris including clearing, rubbing with sand paper, filling gaps, depression etc. where necessary, with chalk powder and and plaster of paris paste, making the surface even and smooth complete at all levels as specified and directed.

Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Wall painting (two coats) with Plastic emulsion paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Finishing old/ new wall with waterproofing weather coat smooth anti-fungal exterior painting of approved make of Berger paint of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels (two coats)

Applying priming coat over new wood based surfaces up to 100mm in girth/width after and including preparing the surface by throughly cleaning oil, grease, dirt snd other foreign matter , sand papering and knotting. (b). With ready mixed paint , Wood primer (white)

Applying primary coat over new steel and other metal surface upto 100m in width or girth after preparing the surface by throughly cleaning oil,grease, dirt and other foreign matter and scoured with wire brushes, fine steels, wood scrapers and sand paper. a). With ready mixed "red-lead/ red oxide" primer.

Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matter sand papering and stopping. (i).Surfaces over 100mm in width or girth. a). General purpose (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture(Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter. (i).Surfaces over 100mm in width or girth. a). General purpose (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

Supplying, fitting, fixing anodised aluminium fittings of approved make, reasonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished ) a) Sliding door bolts i) 300mm x 16mm

Supplying, fitting, fixing anodised aluminium fittings of approved make, reasonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished ) b) Tower bolts iii) 200mm x 12mm

Supplying, fitting, fixing anodised aluminium fittings of approved make, reasonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished ) b) Tower bolts i) 300mm x 12mm

Supplying, fitting, fixing anodised aluminium fittings of approved make, reasonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished ) c) Door handles iii) 150mm

SANITARY AND WATER SUPPLY WORKS: Providing fitting and fixing vitreous water closet squatting pan(indian type W.C orissa pattern ) with all fittings and fixtures complete including cutting and making good the walls and floors wherever required.(Flushing cistern to be paid separately)1.1.1---Indian type WC orissa pattern of size 580x40mma) White i) Parryware make.

Supplying fitting and fixing PVC pipes of 6 kgf/cm2 (Supreme/Prince) or other ISI approved including joining, fittings and fixing with clamps etc. as necessary complete at all levels including below G.L. as directed and specified. a) Exposed surfaces or in trenches. ii) 110 mm dia

Supplying fitting and fixing PVC pipes of 6 kgf/cm2 (Supreme/Prince) or other ISI approved including joining, fittings and fixing with clamps etc. as necessary complete at all levels including below G.L. as directed and specified. a) Exposed surfaces or in trenches. iv) 75 mm dia Gas pipe

Supplying fitting and fixing PVC flushing cistern with all internal fitting with CI brackets including fitting and fixing standard size CP flush pipe,union,clamps etc. complete as directed and specified(Pipes will be measured searately) a) White i) Paraware make.ii) Delux single flush.

(Sani) Supplying , fitting and fixing PVC reducer of (supreme/Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) Exposed surfaces or in trenches. iv) 110 mm x 75 mm

Supplying fitting and fixing PVC cross ‘T’ with door of (supreme/Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) consealed. i) 110 mm x110mm

Supplying fitting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining, fittings and fixing with clamps etc. as necessary complete at all levels including below G.L. as directed and specified. b) Consealed by chiselling or breaking brick wall/ C.C./R.C.C. and good to the damages. ii) 110 mm dia

Providing fitting and fixing 63 mm dia . PVC cowel of ISI make complete as directed and specified. (iv) 75 mm dia PVC cowel of ISI make

Providing vitreous china wash basin with CI/MS brackets,CP brass chain with plug,waste coupling of standard pattern , CP brass china with plug , PVC waste pipe including painting of fittings and brackets, cutting and making good the walls and slabs wherever required(Piller cock,wast coupling are to be paid separately). 1.13.1 PEDESTAL BASIN(With pedestal) (A) Parryware make a) White (iv) Cascade NXT 550x440 with long padestal(Cat no Co404/C0380)

Providing fitting and fixing Mirror with plastic frame of size 500x400mm complete as directed and specified.

Supplying fitting and fixing approved uPVC Pipes of different sizes, with necessary 'R' brand or similar approved uPVC. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. (A) Exposed or in trenches SUPREME/PRINCE etc. d) 25mm dia.

Supplying fitting and fixing approved uPVC Pipes of different sizes, with necessary 'R' brand or similar approved uPVC. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. (A) Exposed or in trenches SUPREME/PRINCE etc. e) 15mm dia.

Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately) (I) Essco make (Delux/Sumthing spl./Tropical) (a) Bib cock short body

Supplying fitting and fixing chrome plated (C.P) Pillar-cock of 15mm dia of approved brand as specified and directed. (I) Sona make (b) Heavy type

13/3.3.1 --- stop cock(heavy)of Sant make i) 15 mm dia.

ELECTRICAL WORKS: Wiring for light/fan/call bell point with 2 x 1.5 sq.mm PVC insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electolitic copper conductor for voltage grade up to 1100 volts (Finloex/RR Kabel/Nicco/Anchor or equivalent make as approved by the Deptt.) with flat 19mm ISI marked casing 'n'caping (AGK/Precision/Presto Plast/Polycab/MW or equivalent make as approved by the Deptt.) in surface sysytem, including 6 Amp flush type switch /bell push (Anchor Penta/Gold Medal/Kolor Kany.korn/Havells or equivalent make approved by the Deptt.) GI/MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover ,ceiling rose (Anchor Penta/Gold Medal/Kolor Kany.korn/Havells or equivalent make approved by the Deptt.) etc. complete as directed and specified by the Deptt.- Medium point upto 6.00 meter length

Wiring for light/fan/call bell point with 2 x 1.5 sq.mm PVC insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electolitic copper conductor for voltage grade up to 1100 volts (Finloex/RR Kabel/Nicco/Anchor or equivalent make as approved by the Deptt.) with flat 19mm ISI marked casing 'n'caping (AGK/Precision/Presto Plast/Polycab/MW or equivalent make as approved by the Deptt.) in surface sysytem, including 6 Amp flush type switch /bell push (Anchor Penta/Gold Medal/Kolor Kany.korn/Havells or equivalent make approved by the Deptt.) GI/MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover ,ceiling rose (Anchor Penta/Gold Medal/Kolor Kany.korn/Havells or equivalent make approved by the Deptt.) etc. complete as directed and specified by the Deptt. - Long point upto 10.00 meter length

Wiring for drawing sub-main laine with PVC insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electolitic copper conductor for voltage grade up to 1100 volts (Finloex/RR Kabel/Nicco /Anchor or equivalent make as approved by the Deptt.) PVC conduit (Berlia/AGK/Precision/Presto Plast/Polycab/MW or equivalent make as approved by the Deptt.) including earth continuity in surface recessed 20 mm dia. 2 mm thick/heavy ISI marked IS:9537 PART - III rigid PVC conduit wire system. - With 2 x 2.5 sq.mm + earth continuity

Wiring for drawing sub-main laine with PVC insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electolitic copper conductor for voltage grade up to 1100 volts (Finloex/RR Kabel/Nicco /Anchor or equivalent make as approved by the Deptt.) PVC conduit (Berlia/AGK/Precision/Presto Plast/Polycab/MW or equivalent make as approved by the Deptt.) including earth continuity in surface recessed 20 mm dia. 2 mm thick/heavy ISI marked IS:9537 PART - III rigid PVC conduit wire system. - With 2 x 4 sq.mm + earth continuity

Supplying and fixing of Switch /Socket flush type (Anchor Penta PC CHERRY /Gold medal/Kolor Kany.korn/Havells or equivalent make as approved by the Deptt) on the existing PVC/MS board including connection as approved by the Deptt.

Supplying and fixing of batten holder (Anchor Penta PC CHERRY /Gold medal/Kolor Kany.korn/Havells or equivalent make as approved by the Deptt) including connection as approved by the Deptt.as required (Without lamp).

Supplying and fixing of 3 plate Ceiling Rose (Anchor Penta PC CHERRY /Gold medal/Kolor Kany.korn/Havells or equivalent make as approved by the Deptt) on the existing block including connection as approved by the Deptt.as required.

Supplying and fitting of 11/15 Watt CFL lamp in the existing batten holder/angle holder/decorative bracket/bulk head fitting/pendent holder etc. as specified and directed by the Deptt.

Supplying and fitting of 18/20 Watt CFL lamp in the existing batten holder/angle holder/decorative bracket/bulk head fitting/pendent holder etc. as specified and directed by the Deptt.

Supplying including fitting and fixing bus bar chamber (HPL/GECO/ or equivalent make) with 4 strips bus bar of length 350/450/600/900 mm made of aluminium alloy or wrought aluminium suitable for 100 Amp capacity complete with all accessories including connection etc. as required complete.

Supplying including fitting and fixing of the following star rated A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection cable, as approved by the Deptt. etc. as required complete and as directed by the department ( Without regulator) (ORIENT PSPO make/Usha make/XROMPTON make /Havells/ATC/V GUARD make) ECBC 1.1.2 - Energy specified 5 - star 1200

Supplying including fitting and fixing of the following A.C. Exhaust fanin the existing hole on the wall of following sweeps with making necessary as approved by the Deptt. etc. as required complete and as directed by the department. - Domestic

Supplying including fitting and fixing of the following A.C. Wall fan of 1200mm sweep with making necessary as approved by the Deptt. etc. as required complete and as directed by the department.

Supplying, fitting and fixing of ceiling fan regulator including connections etc. complete and as directed by the Department. - Electronic Type

Supply,Installation and testing of G.I. earth station with perforated 40mm dia and 4.50 meter long heavy duty G.I pipe with necessary 40 mm dia.G I Fitting such as Socket , Tee, Elbow,Nipple and 50 mm x 40 mm G.I. reducing socket for funnel including locking arrangement 300 mm x 300 mm x 6 mm hinged cover C.I. earth plate complete with digging of earth pit,construction of brick chamber and plastering of both inner and outer surface of wall as specified and directed by the Deptt.

Extra for using salt 5 k and charcoal 64 k in pipe Earth Station pit to provide low impedance ground in location of high soil resistivity as and when required specified by the Department.

Supplying and laying of 8 SWG Copper earth from Earth Electrode (below G.L.) to electrical swith gears or electrical machineries including making necessary connectionas approved ,specified and directed by the Deptt.

Supplying and drawing of weather proof aluminium conductor cable of the following size as directed specified by the Deptt. - 10.00 sq.mm twin core

Supplying with fitting and fixing sheet steel,phosphatised ,powder painted Single door surface mounting MCB DB incorporated with basbar,Neutral link,Earth bar and din rail etc. fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved,specified and directed by the Deptt. - (Schneider neo break ,C & S ,Havells,Standard or equivalent as approved by the Deptt.) - 8 Way SPN single door.

Supplying with fitting and fixing Single pole 10KA 240/415 V 50 Hz MCB of the following capacity complete with making necessary connection as approved,specified and directed by the Deptt. - C Series (Schneider neo break ,C & S ,Havells,V -Guard or equivalent as approved by the Deptt.) - 6 to 32 A

Supplying with fitting and fixing DP 10KA 240/415 V 50 Hz MCB of the following capacity complete with making necessary connection as approved,specified and directed by the Deptt. - C Series (Schneider neo break ,C & S ,Havells,V -Guard or equivalent as approved by the Deptt.) - 40 A

Supplying with fitting and fixing 18 S.W.G. Sheet steel metal boxes of the following sizes in surface/recessed wiring sysytem with suitable size of 3 mm thickness phenolic laminated sheet cover on the front face of the boxes including painting etc. as required and specified by the Deptt. - 200 mm x 150 mm x 60 mm deep (nominal size)

Supplying with fitting and fixing 18 S.W.G. Sheet steel metal boxes of the following sizes in surface/recessed wiring sysytem with suitable size of 3 mm thickness phenolic laminated sheet cover on the front face of the boxes including painting etc. as required and specified by the Deptt. - 200 mm x 250 mm x 60 mm deep (nominal size)

Supplying with fitting and fixing 18 S.W.G. Sheet steel metal boxes of the following sizes in surface/recessed wiring sysytem with suitable size of 3 mm thickness phenolic laminated sheet cover on the front face of the boxes including painting etc. as required and specified by the Deptt. - 250 mm x 300 mm x 60 mm deep (nominal size)

ATMA KOKRAJHAR:CIVIL WORKS: Dismantling all types of corrugated/ trapezoidal sheet roofing including ridges, hips, valleys and gutters etc. and stacking the materials as directed by the department for all levels

Dismantling all types of ceiling, partition and wall lining and stacking the materials as directed by the department for all levels

Dismantling and removing the existing door and window frame (chowkath) both wooden and steel of different sizes without damaging the walls and removing the frame and necessary repairs to the edges of the walls as directed for all levels. (i) Area of Door/window up to 3.00 m2

Dismantling wood work in frames, trusses, purlins and rafters including stacking the materials as directed by the department for all levels.

Demolishing brickwork including stacking of serviceable materials and disposal of unserviceable materials as directed for all levels

Demolishing RCC work including stacking of steel bars and disposal of unserviceable material as directed for all levels

Providing wood work in frame (chowkaths) of doors, windows, cleastory window and other similar works wrought, framed and fixed in position in contact with C.C or brick masonry wall including supplying, fitting and fixing with m.S. hold fast (40mmx3mmx250mm) as per design embeded in cement concrete block in proportion 1:2:3 and with two coats of kiricide oiling to the timber faces in contact with C.C and masonry as directed and specified. (a). With sal wood

Providing undressed wood work in roof truss, rafter, purlin, tie and the like including hoisting and fixing in position with necessary spikes, nails including m.S straps with bolt and nuts etc.nails including m.S straps with bolt and nuts etc.complete with kiricide oiling two coats to all timber members and two coats of anticorrosive paint to m.S straps (m.S flats, angle cleats, and bolt and nuts required for flat and angle cleats wherever use shall be measured and paid separately). a) With sal wood

Bamboo slit walling in timber frame with bamboo slit fitted in to the grooves of the timber frame and stiffened by means of double bamboo slits 25mm wide and not less than 6mm thick spaced at intervals of not more than 400mm apart one slit attached on each side and tied together by means of cane slit/galvd tying wire including 20mm thick cement plaster in prop 1 cement : 6 fine sand on both sides in two coats with curing etc complete (measurement for timber frame shall be measured and paid separately.)

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Upto a depth of 2.00 m below the existing G.L (a) In ordinary soil

Providing brick soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete.(a)Brick on flat soling.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (a)In prop 1:3;6

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (upto 1st floor level). b) Other ISI approved TMT bars(SRMB/ SAI/ BISCON/X-TECH) (For Assam type bldg,drain work,retaining wall and boundary wall etc.)

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (upto 1st floor level). C) ISI approved M.S bar 6mm dia.

Providing and laying plain/reinforced cement croncrete works cement with coarse sand & 20 mm down graded stone aggregate including dewatering if necessary,and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) I) Using mixture machine. (A) In sub-structure up to plinth level Foundation, footing, columns with base, tie and plinth beam, grade beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. (b) M20 or prop. 1:1.5:3

Providing and laying plain/reinforced cement croncrete works cement with coarse sand & 20 mm down graded stone aggregate including dewatering if necessary,and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) I) Using mixture machine. (B)-- In Super structure from plinth level up to 1st floor level. (ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing. (b) M20 or prop. 1:1.5:3

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc. ii) Using 25mm thick plank

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: -Sides of tie beam, grade beams etc.at or below G.L.ii) Using 25mm thick plank.

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: .Columns, Pillars, Posts & Strut (a)Square, Rectangular, polygonal in plan or any shape like Tee/L etc. having plane vertical face (ii)Using 25mm thick plank

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties.(a) For depth not exceeding 1.0M. (ii)Using 25mm thick plank

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in: Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like.a) Floors etc. upto 200mm in thickness.

Brick work in cement morter with 1st class brick including racking out joints and dewatering if necessary, and curing complete as directed I) In sub-structure up to plinth level includiong dewatering if necy.(b). In proportion 1:4.

Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary.(c) With silt (predominantly non plastic) by truck carriage including loading and unloading.

Providing and laying 25mm thick damp proof course with cement concrete in prop 1:1.5:3 with graded stone agg. of 10mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacturer including curing etc. complete as directed.

Pre construction anti-termite treatment at the bottom of foundation pits and walls on either side up to a height of 300mm from bottom of the excavation made for column plinth beam, wall, trenches etc. by applying the emulsion @ 5 (five) litres per square meter of the surface area before starting construction work (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. a) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water i.e 1% solution.

Pre construction anti - termite treatment by applying in the entire levelled area after plinth filling and before laying floor,by applying the emulsion @ 5(five) litres per square meter of the surface to be spread with light rodding so as to ensure proper absorption by the filled up earth (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. a) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water. This provides emulsion containing 1% chloropirophose solution (by weight) i.e 1% solution.

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) (A) 112mm thick brick wall (a). In cement mortar in proportion 1:4

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) (B) 75mm thick brick wall (a). In cement mortar in proportion 1:3

Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary.(c) With silt (predominantly non plastic) by truck carriage including loading and unloading.

Providing fitting, hoisting and fixing of roof trusses including purlins fabricated out of M.S. cicular hollow section conforming to relevant I.S. code, as per approved design and drawings including providing M.S. cleats, base plates, bolts and nuts and one coat of red oxide Zinc Chromate primer and two coats of approved enamel paints complete including fitting necessary cleats etc. for fixing ceiling joists as per design and drawing as directed. a) TATA make circular H.Section.-CHS of Grade YST-310 conforming to IS Specification:1161-1998

Providing corrugated galvd. Iron sheet roofing of TATA SHAKTEE / SAIL including fitting and fixing necessary galvd. J or L hooks, bolts and nuts 8 mm dia with bitumen washer 25 mm dia x 3 mm thick and 1.6 mm thick limpet washer complete excluding cost of roof truss, purlin etc.(roof trusses and purlin etc. measured and paid separately) (d) 0.60mm thick.

Providing galvd iron ridging of TATA SHAKTEE / SAIL including supplying and fixing necessary galvd screws/washers etc. complete as directed. b) 0.50 mm thick ii) 230 mm lapping

Providing wood work in frame of false ceilling partitions etc.sawn wrought framed hoisted and fixed in positon with spikes, nails, m.S flat,angle/ cleats with bolt and nuts complete including kiricide oiling two coats to unexposed surfaces of the timber (m.S flats, angle cleats, and bolt and nuts required for flat and angle cleats wherever use shall be measured and paid separately). (b). With Gamari/Bonsum/Sundi.

Providing, fitting and fixing in position false ceiling of 6mm thick Bison panel (cement bonded particle board) on timber frame of 1st class local wood (Hollock/ Bonsum/ Sundi) of 50mm x 50mm spaced at not more than 1.20m apart , fixed to the wall at the end with necessary nails, wood screws, hooks,bolts etc. including painting (one coat primer and two coats of painting) as necessary complete as directed by the Department for all levels. (a) Both sides commercial

65 mm thick cement concrete floor consisting of 50 mm under layer of cement concrete in prop. 1:3:6 (1cement : 3 coarse sand : 6 coarse aggregate of 25mm and down) and 15 mm thick wearing layer in cement concrete in prop. 1:1:2 (1cement :1 coarse sand : 2 coarse aggregate of size 10mm down) laid in panels and finished with a floating coat of neat cement finish (using cement slurry for bond @ 2.75 kg. per square metre of floor area) including curing etc. complete as directed.

Providing fitting and fixing full pannel doors and windows including oxidised M.S. butt hinges (100mm x75 mm x3.55 mm)with necessay screws(Other fittings to be measured and paid separately) B) With Ist class local wood(Gamari). (ii) 35 mm thick.

Providing, fitting and fixing fully glazed window with sash bars including oxidised m.S butt hings (75mmx60mmx3.15mm) 2nos.on each leaf and 3 nos. on single leaf (glass to be measured and paid separately) B) With Hollock/Gamari ii) 35mm thick.

Providing fitting and fixing anodised aluminium sliding windows and ventil ato rs of standard sections of approved brand (HINDANCO /NALCO /BALCO/ JINDAL /Other equivalent primary producer)Without horizontal glazing bars,joints mitred and welded (manufactured to relevant I.S specifications)and providing and fixing handles,angle cleat, rubber gasket,roller,bolting device,locking arrangements,screws etc. as required comp lete as specified and directed for all levels. a) 2 track sliding window i) 6mm clear glass

Providing fitting and fixing anodised aluminium windows and ventil ato rs of standard sections of approved brand (HINDANCO /NALCO /BALCO/ JINDAL /Other equivalent primary producer)Without horizontal glazing bars,joints mitred and welded (manufactured to relevant I.S specifications)fitted with 6mmx3.15mm lugs 100mm long CC blocks 150mmx100mmx100mm in 1:3:6 mix including providing and fixind handles,frictions stys joining cleat bolting device,locking arrangements,spring catch as required complete as specified and directed for all levels,(cement conc.to be measured and paid separately. a) Side hung and top hungs window and ventilators i) 6mm clear glass

Providing fitting and fixing M.S grill of required pattern for window/ C.windows/ openings with with M.S flat of required spacing in frame all round or squre .S bars with round h bolts and nuts or screws. II.Ornamental grill (c) Fixed to brick work/pcc.

15 mm thick Cement plaster in single coat on single or brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. B) On rough side (b). In cement mortar 1:4

15 mm thick Cement plaster in single coat on single or brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. B) On fair side (b). In cement mortar 1:4

Cement plaster skirting with cement mortar ( 1 cement : 3 coarse sand ) finished with a floating coat of neat cement including rounding of junctions with floor. (a) 15mm thick

Providing and fixing clear sheet glass beded in putty and fixed with/without wooden bidding including necessary cutting and glass to be required sized(payment for wooden bead shall be made separately) (1) Area of glass panes not exceeding 0.15sq.m. (a) 3.00 m thick.

Supplying, fitting, fixing anodised aluminium fittings of approved make, reasonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished ) a) Sliding door bolts i) 300mm x 16mm

Supplying, fitting, fixing anodised aluminium fittings of approved make, reasonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished ) b) Tower bolts ii) 250mm x 12mm

Supplying, fitting, fixing anodised aluminium fittings of approved make, reasonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished ) b) Tower bolts iv) 150mm x 10mm

Supplying, fitting, fixing anodised aluminium fittings of approved make, reasonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished ) c) Door handles iii) 150mm

Providing barge board of size 200mm x 20mm with 1st class local Hollock/ Bonsum timber including fitting and fixing with necessary wood screws etc. complete.

Removing white or colour wash by steel wire brushing and/ or scraping, sand papering and preparing the wall surface smooth including necessary repairs to scratches complete.

Providing two coats of J.K Wall Putty ( White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)

Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Wall painting (two coats) with Plastic emulsion paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Finishing old/ new wall with waterproofing weather coat smooth anti-fungal exterior painting of approved make of Berger paint of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels (two coats)

Applying priming coat over new wood based surfaces up to 100mm in girth/width after and including preparing the surface by throughly cleaning oil, grease, dirt snd other foreign matter , sand papering and knotting. (b). With ready mixed paint , Wood primer (white)

Applying primary coat over new steel and other metal surface upto 100m in width or girth after preparing the surface by throughly cleaning oil,grease, dirt and other foreign matter and scoured with wire brushes, fine steels, wood scrapers and sand paper. a). With ready mixed "red-lead/ red oxide" primer.

Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matter sand papering and stopping. (i).Surfaces over 100mm in width or girth. a). General purpose (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture(Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter. (i).Surfaces over 100mm in width or girth. a). General purpose (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

Providing plinth protection 50mm thick tocement concrete 1 : 3 : 6 with coarse agg.of 20mm nominal size including finishing thesurface with 10mm thick cement plaster in proportion 1:3 with a floating coat of neat cement finished.

Providing drain with brick work in cementmortar in proportion 1:5 with half brick thickside walls and 100mm thick C.C (1:3:6) baseover one brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with afloating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refillingthe sides after completion of work etc. as specified. i)300mm wide and average 150mm deep with bed slope 1 in 150 with initial depth of 100mm.

ELECTRICAL WORKS: Wiring for light/fan/call bell point with 2 x 1.5 sq.mm PVC insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electolitic copper conductor for voltage grade up to 1100 volts (Finloex/RR Kabel/Nicco/Anchor or equivalent make as approved by the Deptt.) with flat 19mm ISI marked casing 'n'caping (AGK/Precision/Presto Plast/Polycab/MW or equivalent make as approved by the Deptt.) in surface sysytem, including 6 Amp flush type switch /bell push (Anchor Penta/Gold Medal/Kolor Kany.korn/Havells or equivalent make approved by the Deptt.) GI/MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover ,ceiling rose (Anchor Penta/Gold Medal/Kolor Kany.korn/Havells or equivalent make approved by the Deptt.) etc. complete as directed and specified by the Deptt. 1.1.1- Short point upto 3.00 meter length

Wiring for light/fan/call bell point with 2 x 1.5 sq.mm PVC insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electolitic copper conductor for voltage grade up to 1100 volts (Finloex/RR Kabel/Nicco/Anchor or equivalent make as approved by the Deptt.) with flat 19mm ISI marked casing 'n'caping (AGK/Precision/Presto Plast/Polycab/MW or equivalent make as approved by the Deptt.) in surface sysytem, including 6 Amp flush type switch /bell push (Anchor Penta/Gold Medal/Kolor Kany.korn/Havells or equivalent make approved by the Deptt.) GI/MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover ,ceiling rose (Anchor Penta/Gold Medal/Kolor Kany.korn/Havells or equivalent make approved by the Deptt.) etc. complete as directed and specified by the Deptt. 1.1.2- Medium point upto 6.00 meter length

Wiring for light/fan/call bell point with 2 x 1.5 sq.mm PVC insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electolitic copper conductor for voltage grade up to 1100 volts (Finloex/RR Kabel/Nicco/Anchor or equivalent make as approved by the Deptt.) with flat 19mm ISI marked casing 'n'caping (AGK/Precision/Presto Plast/Polycab/MW or equivalent make as approved by the Deptt.) in surface sysytem, including 6 Amp flush type switch /bell push (Anchor Penta/Gold Medal/Kolor Kany.korn/Havells or equivalent make approved by the Deptt.) GI/MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover ,ceiling rose (Anchor Penta/Gold Medal/Kolor Kany.korn/Havells or equivalent make approved by the Deptt.) etc. complete as directed and specified by the Deptt. 1.1.3 - Long point upto 10.00 meter length

Wiring to 5 a pin 6 Amps plug point with 1.5 sq.mm PVC insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electolitic copper conductor for voltage grade up to 1100 volts (Finloex/RR Kabel/Nicco/Anchor or equivalent make as approved by the Deptt.) with flat 19mm ISI marked casing 'n'caping (AGK/Precision/Presto Plast/Polycab/MW or equivalent make as approved by the Deptt.) in surface sysytem, including 5 pin 6 Amp flush type plug socket and 6 Amps F/T switch (Anchor Penta/Gold Medal/Kolor Kany.korn/Havells or equivalent make approved by the Deptt.) GI/MS switch board (ISI marked) with phenolic laminated sheet cover including earth continuity with 1.5 sq.mm cable to third pin of the plug cocket etc as required complete,when placed elsewhere.- Medium point upto 6.00 meter length

Wiring for drawing sub-main laine with 2 x 1.5 sq.mm PVC insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electolitic copper conductor for voltage grade up to 1100 volts (Finloex/RR Kabel/Nicco /Anchor or equivalent make as approved by the Deptt.) in surface flat 19 mm ISI marked casing 'n'caping (AGK/Precision/Presto Plast/Polycab/MW or equivalent make as approved by the Deptt.) system including continuity connection as required complete as directed and specified by the Deptt. - With 2 x 1.5 sq.mm cable in flat 19 mm ISI.

Wiring for drawing sub-main laine with 2 x 1.5 sq.mm PVC insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electolitic copper conductor for voltage grade up to 1100 volts (Finloex/RR Kabel/Nicco /Anchor or equivalent make as approved by the Deptt.) in surface flat 19 mm ISI marked casing 'n'caping (AGK/Precision/Presto Plast/Polycab/MW or equivalent make as approved by the Deptt.) system including continuity connection as required complete as directed and specified by the Deptt. - With 2 x 2.5 sq.mm + earth continuity

Wiring for drawing sub-main laine with 2 x 1.5 sq.mm PVC insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electolitic copper conductor for voltage grade up to 1100 volts (Finloex/RR Kabel/Nicco /Anchor or equivalent make as approved by the Deptt.) in surface flat 19 mm ISI marked casing 'n'caping (AGK/Precision/Presto Plast/Polycab/MW or equivalent make as approved by the Deptt.) system including continuity connection as required complete as directed and specified by the Deptt. - With 2 x 6 sq.mm + earth continuity.

Supplying and fixing of Switch /Socket flush type (Anchor Penta PC CHERRY /Gold medal/Kolor Kany.korn/Havells or equivalent make as approved by the Deptt) on the existing PVC/MS board including connection as approved by the Deptt.

Supplying and fixing of batten holder (Anchor Penta PC CHERRY /Gold medal/Kolor Kany.korn/Havells or equivalent make as approved by the Deptt) including connection as approved by the Deptt.as required (Without lamp).

Supplying and fitting of 18/20 Watt CFL lamp in the existing batten holder/angle holder/decorative bracket/bulk head fitting/pendent holder etc. as specified and directed by the Deptt.

Supplying with fitting and fixing sheet steel ,phosphatised,power painted Single door surface mounting MCB DB incorporated with basbar,Neutral link,Earth bar and din rail etc. fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved,specified and directed by the Deptt.15.3.1 - (Schneider neo break ,C & S ,Havells,Standard or equivalent as approved by the Deptt.)15.3.1.2 - 6 Way SPN Single door

Supplying with fitting and fixing Single pole 10KA 240/415 V 50 Hz MCB of the following capacity complete with making necessary connection as approved,specified and directed by the Deptt.16.30.2 - C Series (Schneider neo break ,C & S ,Havells,V -Guard or equivalent as approved by the Deptt.)16.30.2.1 - 6 to 32 A

Supplying with fitting and fixing DP 10KA 240/415 V 50 Hz MCB of the following capacity complete with making necessary connection as approved,specified and directed by the Deptt.16.32.2 - C Series (Schneider neo break ,C & S ,Havells,V -Guard or equivalent as approved by the Deptt.)16.32.2.1 - 6 to 32 A

Supply,Installation and testing of G.I. earth station with perforated 40mm dia and 4.50 meter long heavy duty G.I pipe with necessary 40 mm dia.G I Fitting such as Socket , Tee, Elbow,Nipple and 50 mm x 40 mm G.I. reducing socket for funnel including locking arrangement 300 mm x 300 mm x 6 mm hinged cover C.I. earth plate complete with digging of earth pit,construction of brick chamber and plastering of both inner and outer surface of wall as specified and directed by the Deptt.

Extra for using salt 5 k and charcoal 64 k in pipe Earth Station pit to provide low impedance ground in location of high soil resistivity as and when required specified by the Department.

Supplying and laying of 8 SWG Copper earth from Earth Electrode (below G.L.) to electrical swith gears or electrical machineries including making necessary connectionas approved ,specified and directed by the Deptt.

Supplying including fitting and fixing of the following star rated A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection cable, as approved by the Deptt. etc. as required complete and as directed by the department ( Without regulator) (ORIENT PSPO make/Usha make/XROMPTON make /Havells/ATC/V GUARD make) ECBC 1.1.2 - Energy specified 5 - star 1200

Supplying, fitting and fixing of ceiling fan regulator including connections etc. complete and as directed by the Department. - Electronic Type

M/S Infratech Associates