SPECIAL REPAIR TO BLDG NO P-111 (TROOPS LIVING) AT MIL STN KALKA UNDER GE (I) JUTOGH

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (below and above ground level) complete all as specified and as directed.

M&L for 25mm thick PCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in floor, complete all as specified and directed.

M&L for machine cut Kota stone slab flooring 18-20 mm thick over cement screed bed lad and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 15mm thick screed bed in CM 1:6 complete including taking out existing kota stone slab in floor etc including rubbering surface complete all as specified and directed.

Taking down cement plaster on brick or stone walls incl raking out joints hacking for key & scrubbing down with water etc complete all as specified and directed.

M&L for kota stone slab 16-18mm thick in riser of steps, skirting, dado and pillar laid over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 10mm thick backing coat plaster with CM 1:4, complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 5mm thick on brick/ concrete surfaces in CM 1:3 on ceiling and finishing the surface even and smooth incl taking down old cement plaster, complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying two coat of OBD over 1-2mm (av-1.5mm) thick wall care putty to achieve smooth and even surfaces and complete all as specified and directed .

M&L for preparing new plastered surfaces of ceiling and applying three coat of white wash on ceiling, complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coats of oil bound distemper on wall over 2 mm thick wall cared putty over a coat of primer incl preparation of surface complete all as specified and directed.

M&L for preparation of old plastered surfaces and applying two coat of white wash on ceiling, complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) on brick or concrete surfaces finished even and smooth without using extra cement complete for internal surface complete all as specified and directed.

M&L for providing and applying 2 mm thick wall care putty over external plastered surface to prepare the surface even and smooth. complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of Acrylic smooth exterior weather coat paint of required shade, New work applied @1.67ltr/10 sqm over and including priming coat of exterior primer applied @ 2.2kg/10Sqm) complete all as specified and directed.

M&L for PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate finished even & smooth without using extra cement 75 mm thick as in plinth protection, complete all as specified and directed.

in cement mortar including all quoins arches pillars etc but excluding ashlars facing dressed stone work and precast concrete block, complete all as specified and directed.

M&L for Sub main wiring with two single core 2x6 sqmm FRLS insulated and unsheathed stranded copper conductor along with earth wire 6.0 sqmm drawn in FRLS-H rigid conduit connected to main board complete all as specified and directed. Note: Two runs cable and one number earth wire and suitable FRLS-H conduit shall measured together as unit length.

M&L for cleaning of roof slab surfaces including sweeping clean & washing down with water to remove dust & providing water proofing treatment with polymeric standard water proofing membrane, complete all as specified and directed. (a) M&L preparation of plaster surfaces /RCC roof surfaces and applying one coat of oil bound bituminous primer @0.03 ltr/Sqm (b) M&L applying blown type bitumen @1.20Kg/Sqm of grade 85/25 (c) Supplying and laying modified polymeric water proofing membrane super thermo lay 3mm thick of weight not less than 3.00kg /sqm reinforced with polyester non woven fabric weight not less than 150gm/sqm center core including coping on the surfaces with torch application of membrane with 10cm over laps as required all. (d) Applying two coats of aluminium paint @ 0.2 kg/sqm.

Demolition of mud phuska/ lime concrete in roof any thickness incl. plastering and leaping (whether full thickness removed or only a part thereof) incl of old WPT etc, complete all as specified and directed.

M&L for 40mm thick brick tiles laid on and including 15 mm thick bedding in cement mortar (1:6) and joints grouted flush in cement mortar (1:3) complete all as specified and directed.

M&L for PCC 1:3:6, type C-1, using 20mm graded mechanically crushed stone aggregate as in filling pressed steel frame /hold fast blocks etc., complete all as specified and directed.

Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290 Gde E-165, complete all as specified and directed.

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe 290 Gde E-165, complete all as specified and directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length , complete all as specified and directed. Note: i) M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately. ii) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made, for cupboards.

S&F PVC (SWR) junction single, (Single T 110mm), equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) junction single, (Single T 75mm), equal or unequal with access door, complete all as specified and directed.

S&F PVC (SWR) bends, for 110mm bore pipes, with access doors, complete all as specified and directed.

S&F PVC valve less, symphonic action type, flushing cistern, low level, white, with intel, ball valve, float and handle including brackets, complete all as specified and directed.

S&F PVC (SWR) bends, for 75mm bore pipes, with access doors, complete all as specified and directed.

S&F for PVC heavy duty waste pipes of 40/32 mm dia suitable for wash basin of length 1.0m, complete all as specified and directed.

S&F in repair, Soap dish stainless steel , fixed to plugs with chromium plated brass screws, complete all as specified and directed.

S&F PVC (SWR) vent cowl 110 mm dia, complete all as specified and directed.

S&F in repair 8mm dia, brass chromium plated health faucet with 1 meter long flexible hose and wall hook, complete all as specified and directed.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended item complete all as specified and directed.

M&L for cement concrete 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in surface channels and drains etc complete, including cement concrete surface even and smooth, complete all as specified and directed.

M&L for earthing complete with galvanized steel plate electrode of size 60cmx60cmx6.3 mm thick buried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts , nuts, check nuts and washers of galvanized iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically up to top level of earth pit and then taken horizontally to the earth pit. Cement concrete chamber of PCC 1:3:6, type C-2, using 40 mm graded stone aggregate. The chamber shall be constructed one meter away from edge of earth pit. 50 mm thick pre cast cover of cement concrete 1:2:4, type B-1, using 20 mm graded stone aggregate and MS angle iron 50 x 50 x 6 mm frame including two coats of painting over a red oxide to exposed steel surfaces. excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009), complete all as specified and directed.

M&L for PCC 1:2:4, type B-0, using 12.5mm graded mechanical crushed aggregate for roof kerbs, benching, coping, rounded or chamfered on edges, complete all as specified and directed.

M&L for rolled sections Fe 410 as in main and cross beams, hip and jack rafters; purlins where connected to common rafters, post and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, complete all as specified and directed.

M&L for Keyed pointing to brick wall in CM 1:4, complete all as specified and directed.

All as per Srl item No 127.00 above but for one 15 Amps socket outlet point controlled by one single pole switch one way and wiring with 2.5 Sqmm PVC insulated, stranded, unsheated copper conductor on independent board with continuous earth wire of size 2.5 Sqmm green colours PVC insulated, unsheathed, stranded copper conductor cable, complete all as specified and directed.

S&F stainless steel grating open able 100mm dia size with/without hole including fixing with white cement, complete all as specified and directed.

Excavation in trenches not exc. 1.50m wide and not exc. 1.50m depth for foundation, etc or for manholes/sewage lines etc, n.exc 10 sqm on plan and getting out in hard/ dense soil, complete all as specified and directed.

S&F in repair fancy type shower rose 30cm long CP brass pipe with swivel joint, complete all as specified and directed.

Removing excavated material n exc.50m and deposited where directed at a level n exc 1.5 m above the starting point in soils, complete all as specified and directed.

M&L for 150mm dia Reinforced concrete pipes, class NP-3, laid and jointed complete with collars, complete all as specified and directed.

M&L for concrete bed to drain pipes of 150mm dia including packing under, and hauncing against the sides of pipes after they are laid and tested in cement concrete 1:3:6, type C-2, complete all as specified and directed.

M&L for precast cement concrete 1:2:4, type B-1, using 20mm graded crushed stone aggregate as in cover slabs placed in position over manholes etc including use and waste of necessary formwork, complete all as specified and directed. Note:- Reinforcement and handles shall be measured and paid separately.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm in hard/dense soil, complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4, type B-1, smooth finished and reforming benching as required, complete all as specified and directed.

M&L for TMT bars 10 mm dia and over cut to length bent to shape required and binding with ms wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M&L for PCC 1:2:4, type B-0, using 12.5mm graded mechanical crushed stone aggregate for benching, coping shall be 150mm in radius mixed with acrylic based polymer water proofing compound, complete all as specified and directed. Note: WPC shall be measured and paid separately.

M&L for 100mm thick PCC 1:4:8, Type D-2, using 40mm graded crushed stone aggregate as in sub base of floor, complete all as specified and directed.

M&L for 75mm thick cement concrete 1:4:8, type D-2, using 40mm graded crushed stone aggregate as in sub base, complete all as specified and directed.

M&L for chequered cement concrete tiles pre polished 30cmx30cmx25mm thick, set ,jointed and pointed in neat cement slurry with grey cement and pigment in floors incl 15mm thick screed bed or bedding layer in CM 1:6, complete all as specified and directed.

M&L for continuous brick edging; with width equal to the depth of the brick, laid dry, on edge with burn and clay brick of sub class B old size, complete all as specified and directed.

S&F in repair Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for 15mm bore iron pipe, complete all as specified and directed.

S&F gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed 20mm bore, complete all as specified and directed.

M&L for PCC 1:3:6, type C-1, 20mm graded crushed stone aggregate as in MH PCC incl fair finished drain or channel using extra cement including forms, moulds, mitered/stopped ends etc., complete all as specified and directed.

Taking down carefully unserviceable main switches and distribution boards with fuses/ MCB's (single phase or three phase) of any capacity complete all as specified and directed.

Taking down carefully old unserviceable sub main wiring including meters and making good disturbed surfaces and matching with existing complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 100mm thickness, M-50 Grade with grey cement and pigment, laid over and including 40 mm thick (average) sand cushioning and joints filled with sand complete all as specified and directed.

Removing demolished/ excavated material /soil .n exc 50m depositing were directed at a level n.exc 1.5m above the starting point, complete all as specified and directed.

All as per Srl item No 127.00 above but for one 3 pin 5 Amp socket outlet point controlled by one switch on Independent board, complete all as specified and directed.

S&F factory made single phase and neutral sheet steel made out of CRCA 1.2mm thick, powder coated double door vertical DB 8way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing MCBs and the second for protection of MCBs fitted with colour bus bar of capacity 200 Amps, neutral link, earth bar and din rail. suitable for use on 240V, 50Hz supply, partly immersed in wall and making good disturbed surfaces with matching colour, complete all as specified and directed.

S&F 6 amps, single pole, one way switch urea back piece (IP20), 240V, 50Hz, white in colour, duly ISI marked, complete all as specified and directed.

S&F switch piano flush type 20 amps, single pole one way, white in colour, duly ISI marked complete all as specified and directed.

Taking down carefully existing copper/ alumn point wiring for light/ fan/ bell/ socket 5/15 Amp points complete with fitting an

S&F Socket outlet, UNI, 2 in one 10 Amps & 20 Amps, white in colour, duly ISI marked complete all as specified and directed.

d fixtures such as switches, sockets, ceiling roses, holders and bracket fittings with battens/ conduits/ wires, tube light fittings and making good the disturbed surfaces of walls and roofs etc.and to match with existing colour complete all as specified and directed.

S&F batten holder, 240 volts, 50 Hz, 6Amp, white in colour, duly ISI marked complete all as specified and directed.

S&F rotary stepped type electronic fan regulator for ceiling fan 1200/1400mm size, 240 volts, 6 Amps, 100W, deluxe, white in colour, compatible for BLDC Fans duly ISI marked with fan hook if reqd complete all as specified.

S&F LED light fitting 1 x 20 Watt, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed.

S&F LED bulb of 9/ 10 watts, B-22 CDL, 3 star, 6500K, complete all as specified and directed.

M&L for point wiring complete with 1100 volts grade PVC FRLS-H insulated unsheathed cable of copper conductor, multi stranded of size 1.5 Sqmm, single core, drawn through & including PVC rigid concealed conduit, medium grade of suitable size (not less than 20mm dia) duly ISI marked with all accessories such as bends, reducers, spacers, saddles, junction boxes, Bakelite sheets, sizes for mounting switch/ sockets, fan regulators etc complete with and including continuous earth wire of size 1.5 Sqmm, single core, PVC FRLS-H copper conductor, insulated, unsheathed, stranded (Green colour) connected to common earth dolly, One light/fan/bell/Bldg security light point controlled by one single pole one way switch, complete all as specified and directed.

S&F 6 Amps Socket 2 in 1, Urea back piece (IP20), white in colour, duly ISI marked complete all as specified and directed.

S&F MCB SPN, 40 - 63Amps, 240 volts, 10KA duly ISI marked, in MCB DB, complete with connection testing and commissioning, complete all as specified and directed.

S&F MCB SP, 6-32 Amps, 240 volts, 10KA duly ISI marked, in the MCB DB, complete with connection testing and commissioning, complete all as specified and directed.

S&F ceiling rose surface type, 240 volts, 50 Hz, 6Amp, Pilot 3 plate, white in colour, Bakelite 65 x 50mm, 3 terminals duly ISI marked complete all as specified and directed.

S&F LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/ 66 protection, complete all as specified and directed.

S&F exhaust fan heavy duty steel body with louvers complete of sweep size 300 mm, single phase with bolts, nuts and washers, size of the bolt 15 cm long 12mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection, complete all as specified and directed.

Cutting holes making good the distributed surface, grouting nuts for fixing of Exhaust fans complete all as specified and directed.

S&F factory made three phase and neutral sheet steel made out of CRCA 1.2 mm thick, powder coated double door vertical DB 4way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing MCBs and the second for protection of MCBs fitted with colour bus bar of capacity 200 Amps, neutral link, earth bar and din rail suitable for use on 240/ 415V, 50Hz supply, VTPN DB, partly immersed in wall, including of MCCB 4 pole adjustable thermal & fixed magnetic type 63 Amps, 50Hz, 415 Volts with rupturing capacity 16 KA and making good disturbed surfaces with matching colour, complete all as specified and directed.

Supply, laying, jointing and testing of cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured heavy duty electric cable with multistranded aluminium conductor, 1100 volts grade of size 25 Sqmm, 4 core, confirming to IS:7098 (Part-1) laid in trenches, under road or passing through pipes/ ducts or fixed to walls/ poles complete with proper thimbles complete all as specified and directed.

Supply, laying, jointing and testing of cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured heavy duty electric cable with multistranded aluminium conductor, 1100 volts grade of size 10 Sqmm, 2 core, confirming to IS:7098 (Part-1) laid in trenches, under road or passing through pipes/ ducts or fixed to walls/ poles complete with proper thimbles complete all as specified and directed.

M&L for Sand filling under floors or in foundations including watering and consolidation for UG cable complete all as specified and directed.

M&L for sub class 'B' old size of Brick in trenches for cable protection of LT Cables complete all as specified and directed.

Excavation in trenches in soft/loose soil n.exc 1.5 Mtr deep and n.exc 1.5 mtr wide for laying of HT cable and getting out including dressing/trimming of sides and leveling, grading and ramming of bottom of excavation complete all as specified and directed.